ONEACCESS-JITTER-MIB

All MIBs › ONEACCESS-JITTER-MIB

Organization: OneAccess

Last Updated: 2011-10-27

Category: CPE/Router

Description: Measures and reports network jitter and delay variation on OneAccess CPE routers for SLA monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ONEACCESS-JITTER-MIB?

ONEACCESS-JITTER-MIB is an enterprise MIB from OneAccess (a CPE/branch-router vendor later absorbed into ADTRAN/Ekinops product lines) for measuring network jitter and delay variation on customer-edge routers. It exposes performance/QoS metrics rather than inventory data, focused on delay-variation measurements typically tied to a WAN interface or measurement flow. Its monitoring purpose is squarely on network performance quality rather than physical hardware health: it lets an operator track jitter trends to detect degrading real-time traffic quality, rather than reporting CPU, memory, temperature, or power status. It likely depends on standard interface indexing conventions (IF-MIB) to associate jitter results with the correct WAN interface. It is deployed on OneAccess CPE routers at branch or customer sites to validate VoIP/real-time-traffic SLA compliance over the WAN link, and an ONEACCESS-JITTER-MIB download supplies the object definitions needed to poll those delay-variation metrics.

IPNetwork Monitor allows you to monitor SNMP objects defined in ONEACCESS-JITTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

OneAccess CPE routers
branch-office WAN routers

Monitoring Examples

No object or table names were provided in the source excerpt for this module, so a concrete object-level scenario cannot be grounded here. In general, a jitter MIB of this kind would expose per-interface or per-flow delay-variation statistics that an administrator polls periodically. A rising jitter value on a branch router's WAN interface would signal congestion or a degrading access-link path affecting VoIP call quality before end users notice dropped or garbled calls.

What Can Be Monitored

network jitter / delay variation
WAN link performance trend

Imported Objects

From IF-MIB

OwnerString

From INET-ADDRESS-MIB

InetAddress

From ONEACCESS-GLOBAL-REG

oacExpIMManagement	OBJECT-IDENTITY
oacMIBModules	OBJECT-IDENTITY
oacRequirements	OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DateAndTime
RowStatus
TEXTUAL-CONVENTION
TimeStamp

OIDs

OID symbolic	OID numeric	Type	Access	Description
oacExpIMJitter	1.3.6.1.4.1.13191.10.3.4.5
oacJitterCompliance	1.3.6.1.4.1.13191.5.2000.2.1			The compliance statement for agents that support the ONEACCESS-JITTER-MIB.
oacJitterCompliances	1.3.6.1.4.1.13191.5.2000.2
oacJitterConformance	1.3.6.1.4.1.13191.5.2000
oacJitterControlEntry	1.3.6.1.4.1.13191.10.3.4.5.1.1.1		not-accessible	List of objects defining a conceptual JITTER probe.
INT oacJitterControlFrequency	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.4	INTEGER	read-create	Defines the time in seconds between two probes.
INT oacJitterControlIndex	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.1	INTEGER	not-accessible	Identifies a row (session number) in the control table.
I32 oacJitterControlInterval	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.9	Integer32	read-create	Time interval between each packet of a probe.
STR oacJitterControlOwner	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.2	OwnerString	read-create	Use as a comment field.
I32 oacJitterControlPacketCount	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.11	Integer32	read-create	Number of packets to send for a probe.
I32 oacJitterControlPktDataRequestSize	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.10	Integer32	read-create	Specifies the size of the packet to send.
IP oacJitterControlSourceAddress	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.8	InetAddress	read-create	Specifies the source IP address.
ROW oacJitterControlStatus	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.13	RowStatus	read-create	The status of the jitter probe (see definition from SNMPv2-TC module).
oacJitterControlTable	1.3.6.1.4.1.13191.10.3.4.5.1.1		not-accessible	Config Table for JITTER probe.
IP oacJitterControlTargetAddress	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.6	InetAddress	read-create	Specifies the IP address of the target.
I32 oacJitterControlTargetPort	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.7	Integer32	read-create	Specifies the port number of the target.
INT oacJitterControlTimeout	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.5	INTEGER	read-create	Defines the maximum time of waiting a response to a packet.
I32 oacJitterControlTos	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.12	Integer32	read-create	This object represents the type of service in an IP header.
OAC oacJitterControlType	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.3	OacJitterControlJitterType	read-create	Specifies the protocol used by the probe.
OCT oacJitterControlVrfName	1.3.6.1.4.1.13191.10.3.4.5.1.1.1.14	OCTET STRING	read-write	VRF name
oacJitterGeneralGroup	1.3.6.1.4.1.13191.5.2000.1.1			This group is mandatory for Jitter entity.
oacJitterGroups	1.3.6.1.4.1.13191.5.2000.1
oacJitterMIBModule	1.3.6.1.4.1.13191.1.100.2000			Contact updated
oacJitterObjects	1.3.6.1.4.1.13191.10.3.4.5.1
I32 oacJitterStatsAvgRTT	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.6	Integer32	read-only	The average value of the Round Trip Time measures.
OAC oacJitterStatsCompleted	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.2	OacJitterResponseSense	read-only	The status of the last measure.
I32 oacJitterStatsDeviationDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.36	Integer32	read-only	Standard jitter measures deviation (Source <- Target).
I32 oacJitterStatsDeviationSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.35	Integer32	read-only	Standard jitter measures deviation (Source -> Target).
oacJitterStatsEntry	1.3.6.1.4.1.13191.10.3.4.5.1.2.1		not-accessible	List of objects defining the results for JITTER probe.
I32 oacJitterStatsHistoryAvgRTT	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.6	Integer32	read-only	The average value of the Round Trip Time measures.
OAC oacJitterStatsHistoryCompleted	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.2	OacJitterResponseSense	read-only	The status of the last measure.
I32 oacJitterStatsHistoryDeviationDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.36	Integer32	read-only	Standard jitter measures deviation (Source <- Target).
I32 oacJitterStatsHistoryDeviationSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.35	Integer32	read-only	Standard jitter measures deviation (Source -> Target).
oacJitterStatsHistoryEntry	1.3.6.1.4.1.13191.10.3.4.5.1.3.1		not-accessible	List of objects defining the history results for JITTER probe.
I32 oacJitterStatsHistoryIndex	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.1	Integer32	read-only	The index of the entry.
I32 oacJitterStatsHistoryMaxNegDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.30	Integer32	read-only	The maximum measure of negative jitter measures (Source <- Target).
I32 oacJitterStatsHistoryMaxNegSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.28	Integer32	read-only	The maximum measure of negative jitter measures (Source -> Target).
I32 oacJitterStatsHistoryMaxPosDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.29	Integer32	read-only	The maximum measure of positive jitter measures (Source <- Target).
I32 oacJitterStatsHistoryMaxPosSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.27	Integer32	read-only	The maximum measure of positive jitter measures (Source -> Target).
I32 oacJitterStatsHistoryMaxRTT	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.9	Integer32	read-only	The maximum value of the Round Trip Time measures.
I32 oacJitterStatsHistoryMinRTT	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.8	Integer32	read-only	The minimum value of the Round Trip Time measures.
I32 oacJitterStatsHistoryNumNegDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.21	Integer32	read-only	The number of negative jitter measures (Source <- Target).
I32 oacJitterStatsHistoryNumNegJitter	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.13	Integer32	read-only	The number of negative jitter mesures (Source Target).
I32 oacJitterStatsHistoryNumNegSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.17	Integer32	read-only	The number of negative jitter measures (Source -> Target).
I32 oacJitterStatsHistoryNumPosDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.19	Integer32	read-only	The number of positive jitter measures (Source <- Target).
I32 oacJitterStatsHistoryNumPosJitter	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.11	Integer32	read-only	The number of positive jitter measures (Source Target).
I32 oacJitterStatsHistoryNumPosSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.15	Integer32	read-only	The number of positive jitter measures (Source -> Target).
I32 oacJitterStatsHistoryNumRTT	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.4	Integer32	read-only	The total number of probe operations that have been done.
I32 oacJitterStatsHistoryPacketLateArrival	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.25	Integer32	read-only	The number of packets that arrived after the timeout.
I32 oacJitterStatsHistoryPacketLoss	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.26	Integer32	read-only	The number of packets that are lost for which we cannot determine the direction.
I32 oacJitterStatsHistoryPacketLossDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.23	Integer32	read-only	The number of packets lost when sent from target to source.
I32 oacJitterStatsHistoryPacketLossSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.22	Integer32	read-only	The number of packets lost when sent from source to target.
I32 oacJitterStatsHistoryPacketOutOfSequence	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.24	Integer32	read-only	The number of packets arrived out of sequence.
I32 oacJitterStatsHistoryPacketRecv	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.5	Integer32	read-only	The number of received packets during a probe test.
I32 oacJitterStatsHistorySum2NegDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.34	Integer32	read-only	The sum of squared negative jitter measures (Source <- Target).
I32 oacJitterStatsHistorySum2NegSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.32	Integer32	read-only	The sum of squared negative jitter measures (Source -> Target).
I32 oacJitterStatsHistorySum2PosDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.33	Integer32	read-only	The sum of squared positive jitter measures (Source <- Target).
I32 oacJitterStatsHistorySum2PosSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.31	Integer32	read-only	The sum of squared positive jitter measures (Source -> Target).
I32 oacJitterStatsHistorySumNegDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.20	Integer32	read-only	The sum of negative jitter measures (Source <- Target).
I32 oacJitterStatsHistorySumNegJitter	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.12	Integer32	read-only	The sum of negative jitter measures (Source Target).
I32 oacJitterStatsHistorySumNegSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.16	Integer32	read-only	The sum of negative jitter measures (Source -> Target).
I32 oacJitterStatsHistorySumPosDS	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.18	Integer32	read-only	The sum of positive jitter measures (Source <- Target).
I32 oacJitterStatsHistorySumPosJitter	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.10	Integer32	read-only	The sum of positive jitter measures (Source Target).
I32 oacJitterStatsHistorySumPosSD	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.14	Integer32	read-only	The sum of positive jitter measures (Source -> Target).
I32 oacJitterStatsHistorySumRTT	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.7	Integer32	read-only	The sum of the Round Trip Time measures.
oacJitterStatsHistoryTable	1.3.6.1.4.1.13191.10.3.4.5.1.3		not-accessible	Statistics History Table for JITTER probe.
DAT oacJitterStatsHistoryTime	1.3.6.1.4.1.13191.10.3.4.5.1.3.1.3	DateAndTime	read-only	The date of the last measure.
I32 oacJitterStatsMaxNegDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.30	Integer32	read-only	The maximum measure of negative jitter measures (Source <- Target).
I32 oacJitterStatsMaxNegSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.28	Integer32	read-only	The maximum measure of negative jitter measures (Source -> Target).
I32 oacJitterStatsMaxPosDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.29	Integer32	read-only	The maximum measure of positive jitter measures (Source <- Target).
I32 oacJitterStatsMaxPosSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.27	Integer32	read-only	The maximum measure of positive jitter measures (Source -> Target).
I32 oacJitterStatsMaxRTT	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.9	Integer32	read-only	The maximum value of the Round Trip Time measures.
I32 oacJitterStatsMinRTT	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.8	Integer32	read-only	The minimum value of the Round Trip Time measures.
I32 oacJitterStatsNumNegDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.21	Integer32	read-only	The number of negative jitter measures (Source <- Target).
I32 oacJitterStatsNumNegJitter	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.13	Integer32	read-only	The number of negative jitter mesures (Source Target).
I32 oacJitterStatsNumNegSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.17	Integer32	read-only	The number of negative jitter measures (Source -> Target).
I32 oacJitterStatsNumPosDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.19	Integer32	read-only	The number of positive jitter measures (Source <- Target).
I32 oacJitterStatsNumPosJitter	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.11	Integer32	read-only	The number of positive jitter measures (Source Target).
I32 oacJitterStatsNumPosSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.15	Integer32	read-only	The number of positive jitter measures (Source -> Target).
I32 oacJitterStatsNumRTT	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.4	Integer32	read-only	The total number of probe operations that have been done.
I32 oacJitterStatsPacketLateArrival	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.25	Integer32	read-only	The number of packets that arrived after the timeout.
I32 oacJitterStatsPacketLoss	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.26	Integer32	read-only	The number of packets that are lost for which we cannot determine the direction.
I32 oacJitterStatsPacketLossDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.23	Integer32	read-only	The number of packets lost when sent from target to source.
I32 oacJitterStatsPacketLossSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.22	Integer32	read-only	The number of packets lost when sent from source to target.
I32 oacJitterStatsPacketOutOfSequence	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.24	Integer32	read-only	The number of packets arrived out of sequence.
I32 oacJitterStatsPacketRecv	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.5	Integer32	read-only	The number of received packets during a probe test.
I32 oacJitterStatsSum2NegDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.34	Integer32	read-only	The sum of squared negative jitter measures (Source <- Target).
I32 oacJitterStatsSum2NegSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.32	Integer32	read-only	The sum of squared negative jitter measures (Source -> Target).
I32 oacJitterStatsSum2PosDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.33	Integer32	read-only	The sum of squared positive jitter measures (Source <- Target).
I32 oacJitterStatsSum2PosSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.31	Integer32	read-only	The sum of squared positive jitter measures (Source -> Target).
I32 oacJitterStatsSumNegDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.20	Integer32	read-only	The sum of negative jitter measures (Source <- Target).
I32 oacJitterStatsSumNegJitter	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.12	Integer32	read-only	The sum of negative jitter measures (Source Target).
I32 oacJitterStatsSumNegSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.16	Integer32	read-only	The sum of negative jitter measures (Source -> Target).
I32 oacJitterStatsSumPosDS	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.18	Integer32	read-only	The sum of positive jitter measures (Source <- Target).
I32 oacJitterStatsSumPosJitter	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.10	Integer32	read-only	The sum of positive jitter measures (Source Target).
I32 oacJitterStatsSumPosSD	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.14	Integer32	read-only	The sum of positive jitter measures (Source -> Target).
I32 oacJitterStatsSumRTT	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.7	Integer32	read-only	The sum of the Round Trip Time measures.
oacJitterStatsTable	1.3.6.1.4.1.13191.10.3.4.5.1.2		not-accessible	Statistics Table for JITTER probe.
DAT oacJitterStatsTime	1.3.6.1.4.1.13191.10.3.4.5.1.2.1.3	DateAndTime	read-only	The date of the last measure.

RFC description

OneAccess jitter measurement and statistics MIB; provides configuration and statistical monitoring for network jitter testing probes.

Start monitoring OneAccess CPE router (WAN jitter/delay-variation measurement) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ONEACCESS-JITTER-MIB

What Is ONEACCESS-JITTER-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description