NTWS-TRAP-MIB

All MIBs › NTWS-TRAP-MIB

Organization: Nortel Networks

Last Updated: 2008-05-15

Category: Nortel WLAN

Description: Defines SNMP traps for AP state changes, client events, and controller fault conditions on Nortel NTWS platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NTWS-TRAP-MIB?

NTWS-TRAP-MIB is the fault/event notification MIB for Nortel's NTWS wireless LAN platform, defining the SNMP traps the Access Controller and its Access Points emit for state changes, client events, and controller fault conditions. Its varbind objects carry contextual data for these traps, including device and mobility-domain identifiers, AP and client MAC addresses, detected rogue-transmitter MAC address, port and radio number, RSSI, BSSID, username, authentication server IP, and client session state. As a notification-focused MIB it is squarely about software/operational status monitoring: it is how the controller proactively alerts a management station to AP up/down transitions, client authentication or session-state changes, RF/rogue detection events, and other fault conditions, rather than requiring constant polling. It is designed to work hand-in-hand with the data-oriented NTWS MIBs in this family (NTWS-AP-STATUS-MIB, NTWS-CLIENT-SESSION-MIB, and NTWS-INFO-RF-DETECT-MIB), since its trap varbinds reference the same identifiers (AP serial/MAC, client MAC, RF transmitter MAC) defined there. It is deployed on Nortel NTWS wireless controllers as the real-time alerting layer of an enterprise WLAN deployment. Engineers can download the NTWS-TRAP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in NTWS-TRAP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel NTWS wireless LAN controllers (Access Controllers) and managed Access Points

Monitoring Examples

A trap carrying ntwsAPMACAddress and ntwsPortNum together with a state-change indication would alert an operator that a specific AP just went down, while a trap including ntwsClientMACAddress, ntwsUserName, and ntwsClientSessionState would signal a client authentication or session event needing attention. A burst of traps referencing ntwsRFDetectXmtrMacAddr and ntwsRadioRssi in a short window would reveal a wave of newly detected RF transmitters, prompting investigation into a potential rogue AP incident.

What Can Be Monitored

AP state-change events
client authentication/session events
rogue/RF transmitter detection events
client RSSI at time of event
controller fault conditions
mobility domain and device identifiers in alerts

Imported Objects

From NTWS-AP-TC

NtwsAccessType
NtwsApAttachType
NtwsApConnectSecurityType
NtwsApFailDetail
NtwsApFingerprint
NtwsApNum
NtwsApPortOrDapNum
NtwsApSerialNum
NtwsApServiceAvailability
NtwsApTransition
NtwsApWasOperational
NtwsChannelChangeType
NtwsCryptoType
NtwsPowerLevel
NtwsRadioChannelWidth
NtwsRadioConfigState
NtwsRadioMimoState
NtwsRadioMode
NtwsRadioNum
NtwsRadioPowerChangeType
NtwsRadioType

From NTWS-CLIENT-SESSION-TC

NtwsClientAccessMode
NtwsClientAuthenProtocolType
NtwsClientDot1xState
NtwsClientSessionState
NtwsUserAccessType

From NTWS-RF-DETECT-TC

NtwsRFDetectClassificationReason

From NTWS-ROOT-MIB

ntwsMibs	OBJECT-IDENTITY
ntwsTemporary	OBJECT-IDENTITY
ntwsTraps	OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
OID ntwsDeviceId	1.3.6.1.4.1.45.6.1.2.1	OBJECT IDENTIFIER	accessible-for-notify	Enumeration of devices as indicated in registration MIB. This object is used within notifications and is not accessible.
IP ntwsMobilityDomainIp	1.3.6.1.4.1.45.6.1.2.2	IpAddress	accessible-for-notify	IP address of the other switch which the send switch is reporting on. This object is used within notifications and is not accessible.
MAC ntwsAPMACAddress	1.3.6.1.4.1.45.6.1.2.3	MacAddress	accessible-for-notify	MAC address of the AP of interest. This object is used within notifications and is not accessible.
MAC ntwsClientMACAddress	1.3.6.1.4.1.45.6.1.2.4	MacAddress	accessible-for-notify	MAC address of the client of interest. This object is used within notifications and is not accessible.
MAC ntwsRFDetectXmtrMacAddr	1.3.6.1.4.1.45.6.1.2.5	MacAddress	accessible-for-notify	Describes the transmitter's MAC address. This object is used within notifications and is not accessible.
INT ntwsPortNum	1.3.6.1.4.1.45.6.1.2.6	INTEGER	accessible-for-notify	Port number on the AC which reported this rogue during a detection sweep. This object is used within notifications and is not accessible.
NTW ntwsAPRadioNum	1.3.6.1.4.1.45.6.1.2.7	NtwsRadioNum	accessible-for-notify	Radio number of the AP which reported this rogue during a detection sweep. This object is used within notifications and is not accessible.
INT ntwsRadioRssi	1.3.6.1.4.1.45.6.1.2.8	INTEGER	accessible-for-notify	The received signal strength as measured by the AP radio which reported this rogue during a detection sweep. This object is used within notifications and is not accessible. Not used by any notification.
OCT ntwsRadioBSSID	1.3.6.1.4.1.45.6.1.2.9	OCTET STRING	accessible-for-notify	The basic service set identifier of the rogue from the beacon frame reported by the AP during a detection sweep. This object is used within notifications and is not accessible.
STR ntwsUserName	1.3.6.1.4.1.45.6.1.2.10	DisplayString	accessible-for-notify	The client user name as learned from the AAA process. This object is used within notifications and is not accessible.
IP ntwsClientAuthServerIp	1.3.6.1.4.1.45.6.1.2.11	IpAddress	accessible-for-notify	The client authentication server ip address. This object is used within notifications and is not accessible.
NTW ntwsClientSessionState	1.3.6.1.4.1.45.6.1.2.12	NtwsClientSessionState	accessible-for-notify	The state for a client session. This object is used within notifications and is not accessible.
INT ntwsDAPNum	1.3.6.1.4.1.45.6.1.2.13	INTEGER	accessible-for-notify	The DAP number on the wireless switch. This object is used within notifications and is not accessible.
IP ntwsClientIp	1.3.6.1.4.1.45.6.1.2.14	IpAddress	accessible-for-notify	The client ip address. This object is used within notifications and is not accessible.
STR ntwsClientSessionId	1.3.6.1.4.1.45.6.1.2.15	DisplayString	accessible-for-notify	The unique global id for a client session. This object is used within notifications and is not accessible.
NTW ntwsClientAuthenProtocolType	1.3.6.1.4.1.45.6.1.2.16	NtwsClientAuthenProtocolType	accessible-for-notify	The authentication protocol for a client. This object is used within notifications and is not accessible.
STR ntwsClientVLANName	1.3.6.1.4.1.45.6.1.2.17	DisplayString	accessible-for-notify	The vlan name a client is on. This object is used within notifications and is not accessible.
TIK ntwsClientSessionStartTime	1.3.6.1.4.1.45.6.1.2.18	TimeTicks	accessible-for-notify	The start time of a client session, relative to the sysUptime. This object is used within notifications and is not accessible. Obsolete. Do not use it because it's not vital information and often cannot be implemented to match the declared semantics: a client session might have been created on another wireless switch, before the current switch booted (the local zero of sysUptime).
STR ntwsClientFailureCause	1.3.6.1.4.1.45.6.1.2.19	DisplayString	accessible-for-notify	Display string for possible failure cause for a client session. This object is used within notifications and is not accessible.
INT ntwsClientRoamedFromPortNum	1.3.6.1.4.1.45.6.1.2.20	INTEGER	accessible-for-notify	The port number on the AC a client has roamed from. This object is used within notifications and is not accessible.
NTW ntwsClientRoamedFromRadioNum	1.3.6.1.4.1.45.6.1.2.21	NtwsRadioNum	accessible-for-notify	The radio number of the AP the client is roamed from. This object is used within notifications and is not accessible.
INT ntwsClientRoamedFromDAPNum	1.3.6.1.4.1.45.6.1.2.22	INTEGER	accessible-for-notify	The DAP number on the AC which reported this rogue during roam. This object is used within notifications and is not accessible.
STR ntwsUserParams	1.3.6.1.4.1.45.6.1.2.23	DisplayString	accessible-for-notify	A display string of User Parameters for client user authorization attributes learned through AAA and/or used by the system. Note that the syntax will be (name=value, name=value,..) for the parsing purpose. This object is used within notifications and is not accessible.
INT ntwsClientLocationPolicyIndex	1.3.6.1.4.1.45.6.1.2.24	INTEGER	accessible-for-notify	Index of the Location Policy rule applied to a user. This object is used within notifications and is not accessible.
NTW ntwsClientAssociationFailureCause	1.3.6.1.4.1.45.6.1.2.25	NtwsAssociationFailureType	accessible-for-notify	The client association failure cause. This object is used within notifications and is not accessible.
NTW ntwsClientAuthenticationFailureCause	1.3.6.1.4.1.45.6.1.2.26	NtwsAuthenticationFailureType	accessible-for-notify	The client authentication failure cause. This object is used within notifications and is not accessible.
NTW ntwsClientAuthorizationFailureCause	1.3.6.1.4.1.45.6.1.2.27	NtwsAuthorizationFailureType	accessible-for-notify	The client authorization failure cause. Note that if it is the user-param, we would additionally expect the failure cause description to list the user attribute value that caused the failure. This object is used within notifications and is not accessible.
STR ntwsClientFailureCauseDescription	1.3.6.1.4.1.45.6.1.2.28	DisplayString	accessible-for-notify	Display string for describing the client failure cause. This object is used within notifications and is not accessible.
IP ntwsClientRoamedFromWsIp	1.3.6.1.4.1.45.6.1.2.29	IpAddress	accessible-for-notify	The system IP address of the AC (wireless switch) a client roamed from. This object is used within notifications and is not accessible.
NTW ntwsClientRoamedFromAccessType	1.3.6.1.4.1.45.6.1.2.30	NtwsAccessType	accessible-for-notify	The client access type (ap, dap, wired) that a client roamed from. This object is used within notifications and is not accessible.
NTW ntwsClientAccessType	1.3.6.1.4.1.45.6.1.2.31	NtwsAccessType	accessible-for-notify	The client access type (ap, dap, wired). This object is used within notifications and is not accessible. For new traps, use ntwsClientAccessMode instead of this object.
MAC ntwsRadioMACAddress	1.3.6.1.4.1.45.6.1.2.32	MacAddress	accessible-for-notify	AP Radio MAC address. This object is used within notifications and is not accessible.
NTW ntwsRadioPowerChangeReason	1.3.6.1.4.1.45.6.1.2.33	NtwsRadioPowerChangeType	accessible-for-notify	The type of event that caused an AP radio power change; occurs due to auto-tune operation. This object is used within notifications and is not accessible.
INT ntwsNewChannelNum	1.3.6.1.4.1.45.6.1.2.34	INTEGER	accessible-for-notify	New channel number of the AP radio used after an auto tune event. This object is used within notifications and is not accessible.
INT ntwsOldChannelNum	1.3.6.1.4.1.45.6.1.2.35	INTEGER	accessible-for-notify	Old channel number of the AP radio used before an auto tune event. This object is used within notifications and is not accessible.
NTW ntwsChannelChangeReason	1.3.6.1.4.1.45.6.1.2.36	NtwsChannelChangeType	accessible-for-notify	The type of event that caused an AP radio channel change; occurs due to auto-tune operation. This object is used within notifications and is not accessible.
OCT ntwsRFDetectListenerListInfo	1.3.6.1.4.1.45.6.1.2.37	OCTET STRING	accessible-for-notify	The RF Detection Listener list info including a list of (listener mac, rssi, channel, ssid, time). There will be a maximum of 6 entries in the list. Formats: MAC: 18 bytes: %2.2X:%2.2X:%2.2X:%2.2X:%2.2X:%2.2X RSSI: 10 bytes: %10d CHANNEL: 3 bytes: %3d SSID: 32 bytes: %s TIME: 26 bytes: %s Maximum size per entry is 89+4+2 = 95 bytes. Maximum size of the string is 6*95= 571 bytes (include NULL). This object is used within notifications and is not accessible.
STR ntwsRadioSSID	1.3.6.1.4.1.45.6.1.2.38	DisplayString	accessible-for-notify	The radio SSID string This object is used within notifications and is not accessible.
NTW ntwsNewPowerLevel	1.3.6.1.4.1.45.6.1.2.39	NtwsPowerLevel	accessible-for-notify	New power level of the AP radio used after an auto tune event. This object is used within notifications and is not accessible.
NTW ntwsOldPowerLevel	1.3.6.1.4.1.45.6.1.2.40	NtwsPowerLevel	accessible-for-notify	Old power level of the AP radio used before an auto tune event. This object is used within notifications and is not accessible.
STR ntwsRadioPowerChangeDescription	1.3.6.1.4.1.45.6.1.2.41	DisplayString	accessible-for-notify	The radio power change description. In the case of reason being dup-pkts-threshold-exceed(1), and retransmit-threshold-exceed(2), clientMacAddress will be included in the description. This object is used within notifications and is not accessible.
STR ntwsCounterMeasurePerformerListInfo	1.3.6.1.4.1.45.6.1.2.42	DisplayString	accessible-for-notify	A list of information for APs performing Counter Measures including a list of performer mac addresses. This object is used within notifications and is not accessible. Not used by any notification.
NTW ntwsClientDot1xState	1.3.6.1.4.1.45.6.1.2.43	NtwsClientDot1xState	accessible-for-notify	The state for a client 802.1X. This object is used within notifications and is not accessible.
NTW ntwsClientDot1xFailureCause	1.3.6.1.4.1.45.6.1.2.44	NtwsDot1xFailureType	accessible-for-notify	The client 802.1X failure cause. This object is used within notifications and is not accessible.
NTW ntwsAPAccessType	1.3.6.1.4.1.45.6.1.2.45	NtwsAccessType	accessible-for-notify	The access point access type (ap, dap,). This object is used within notifications and is not accessible. Not used by any notification.
NTW ntwsUserAccessType	1.3.6.1.4.1.45.6.1.2.46	NtwsUserAccessType	accessible-for-notify	The user access type (MAC, WEB, DOT1X, LAST-RESORT). This object is used within notifications and is not accessible.
TIK ntwsClientSessionElapsedTime	1.3.6.1.4.1.45.6.1.2.47	TimeTicks	accessible-for-notify	The elapsed time for a client session. Obsoleted because session time is usually reported in seconds. This object is used within notifications and is not accessible.
INT ntwsLocalId	1.3.6.1.4.1.45.6.1.2.48	INTEGER	accessible-for-notify	Local Id for the session. This object is used within notifications and is not accessible.
NTW ntwsRFDetectDoSType	1.3.6.1.4.1.45.6.1.2.49	NtwsRFDetectDoSType	accessible-for-notify	The type of denial of service (DoS) attack. This object is used within notifications and is not accessible.
IP ntwsSourceWsIp	1.3.6.1.4.1.45.6.1.2.50	IpAddress	accessible-for-notify	IP address of another AC (wireless switch). This object is used within notifications and is not accessible.
INT ntwsClientVLANid	1.3.6.1.4.1.45.6.1.2.51	INTEGER	accessible-for-notify	VLAN ID used by client traffic. This object is used within notifications and is not accessible.
INT ntwsClientVLANtag	1.3.6.1.4.1.45.6.1.2.52	INTEGER	accessible-for-notify	VLAN tag used by client traffic. This object is used within notifications and is not accessible.
STR ntwsDeviceModel	1.3.6.1.4.1.45.6.1.2.53	DisplayString	accessible-for-notify	The model of a device in printable US-ASCII. If unknown (or not available), then the value is a zero length string. This object is used within notifications and is not accessible.
NTW ntwsDeviceSerNum	1.3.6.1.4.1.45.6.1.2.54	NtwsApSerialNum	accessible-for-notify	The serial number of an AP in printable US-ASCII. If unknown (or not available), then the value is a zero length string. Should NOT be used to identify other devices, for example an AC (wireless switch). This object is used within notifications and is not accessible.
NUM ntwsRsaPubKeyFingerPrint	1.3.6.1.4.1.45.6.1.2.55	NtwsApFingerprint	accessible-for-notify	The hash of the RSA public key (of a key pair) in binary form that uniquely identifies the public key of an AP. This object is used within notifications and is not accessible.
INT ntwsDAPconnectWarningType	1.3.6.1.4.1.45.6.1.2.56	INTEGER	accessible-for-notify	The type of DAP connect warning. The values are: not-configured-fingerprint-connect(1)...a DAP, which has an RSA keypair but did not have its fingerprint configured on the AC, has connected to the AC when 'dap security' set to 'OPTIONAL' secure-handshake-failure(2).............a DAP tried to connect to the AC with security, but the handshake failed not-configured-fingerprint-required(3)..a DAP tried to connect to the AC with security, but 'dap security' set to 'REQUIRED', and no fingerprint was configured for the DAP fingerprint-mismatch(4).................a DAP tried to connect to the AC with security and its fingerprint was configured, but the fingerprint did not match the computed one This object is used within notifications and is not accessible.
MAC ntwsClientMACAddress2	1.3.6.1.4.1.45.6.1.2.57	MacAddress	accessible-for-notify	MAC address of the second client of interest. This object is used within notifications and is not accessible.
NTW ntwsApAttachType	1.3.6.1.4.1.45.6.1.2.58	NtwsApAttachType	accessible-for-notify	How the AP is attached to the AC (directly or via L2/L3 network). This object is used within notifications and is not accessible.
NTW ntwsApPortOrDapNum	1.3.6.1.4.1.45.6.1.2.59	NtwsApPortOrDapNum	accessible-for-notify	The Port Number if the AP is directly attached, or the CLI-assigned DAP Number if attached via L2/L3 network. This object is used within notifications and is not accessible. Obsoleted by ntwsApNum. (In 6.0, direct- and network-attached APs were unified.)
STR ntwsApName	1.3.6.1.4.1.45.6.1.2.60	DisplayString	accessible-for-notify	The name of the AP, as assigned in AC's CLI; defaults to AP (examples: 'AP01', 'AP22', 'AP333', 'AP4444'); could have been changed from CLI to a meaningful name, for example the location of the AP (example: 'MeetingRoom73'). This object is used within notifications and is not accessible.
NTW ntwsApTransition	1.3.6.1.4.1.45.6.1.2.61	NtwsApTransition	accessible-for-notify	AP state Transition, as seen by the AC. This object is used within notifications and is not accessible.
NTW ntwsApFailDetail	1.3.6.1.4.1.45.6.1.2.62	NtwsApFailDetail	accessible-for-notify	Detailed failure code for some of the transitions specified in 'ntwsApTransition' object. This object is used within notifications and is not accessible.
NTW ntwsRadioType	1.3.6.1.4.1.45.6.1.2.63	NtwsRadioType	accessible-for-notify	Indicates the AP Radio Type, as seen by AC. This object is used within notifications and is not accessible.
NTW ntwsRadioConfigState	1.3.6.1.4.1.45.6.1.2.64	NtwsRadioConfigState	accessible-for-notify	Indicates the Radio State, as seen by the AC. This object is used within notifications and is not accessible.
NTW ntwsApConnectSecurityType	1.3.6.1.4.1.45.6.1.2.65	NtwsApConnectSecurityType	accessible-for-notify	Indicates the security level of the connection between AP and AC. This object is used within notifications and is not accessible.
NTW ntwsApServiceAvailability	1.3.6.1.4.1.45.6.1.2.66	NtwsApServiceAvailability	accessible-for-notify	Indicates the level of wireless service availability. This object is used within notifications and is not accessible.
NTW ntwsApWasOperational	1.3.6.1.4.1.45.6.1.2.67	NtwsApWasOperational	accessible-for-notify	Indicates whether the AP was operational before a transition occured. This object is used within notifications and is not accessible.
U32 ntwsClientTimeSinceLastRoam	1.3.6.1.4.1.45.6.1.2.68	Unsigned32	accessible-for-notify	The time in seconds since the most recent roam of a given client. This object is used within notifications and is not accessible.
NTW ntwsClientIpAddrChangeReason	1.3.6.1.4.1.45.6.1.2.69	NtwsClientIpAddrChangeReason	accessible-for-notify	Indicates the reason why client IP address changed. This object is used within notifications and is not accessible.
MAC ntwsRFDetectRogueAPMacAddr	1.3.6.1.4.1.45.6.1.2.70	MacAddress	accessible-for-notify	Describes the MAC address of the Rogue AP the transmitter is connected to. This object is used within notifications and is not accessible.
U32 ntwsBlacklistingRemainingTime	1.3.6.1.4.1.45.6.1.2.71	Unsigned32	accessible-for-notify	The time in seconds remaining until a given transmitter could be removed from the Black List. This object is used within notifications and is not accessible.
NTW ntwsBlacklistingCause	1.3.6.1.4.1.45.6.1.2.72	NtwsBlacklistingCause	accessible-for-notify	Indicates the reason why a given transmitter is blacklisted. This object is used within notifications and is not accessible.
U32 ntwsNumLicensedActiveAPs	1.3.6.1.4.1.45.6.1.2.73	Unsigned32	accessible-for-notify	Indicates the maximum (licensed) number of active APs for this AC. This object is used within notifications and is not accessible.
IP ntwsClientDynAuthorClientIp	1.3.6.1.4.1.45.6.1.2.74	IpAddress	accessible-for-notify	The dynamic authorization client IP address which caused the change of authorization. This object is used within notifications and is not accessible.
NTW ntwsChangedUserParamOldValues	1.3.6.1.4.1.45.6.1.2.75	NtwsUserAttributeList	accessible-for-notify	A display string listing the changed AAA attributes and their values, before the change of authorization was executed. This object is used within notifications and is not accessible.
NTW ntwsChangedUserParamNewValues	1.3.6.1.4.1.45.6.1.2.76	NtwsUserAttributeList	accessible-for-notify	A display string listing the changed AAA attributes and their values, after the change of authorization was executed. This object is used within notifications and is not accessible.
NTW ntwsClientDisconnectSource	1.3.6.1.4.1.45.6.1.2.77	NtwsSessionDisconnectType	accessible-for-notify	The external source that initiated the termination of a session. This object is used within notifications and is not accessible.
STR ntwsClientDisconnectDescription	1.3.6.1.4.1.45.6.1.2.78	DisplayString	accessible-for-notify	Display string for providing available information related to the external source that initiated a session termination. This object is used within notifications and is not accessible.
IP ntwsMobilityDomainSecondarySeedIp	1.3.6.1.4.1.45.6.1.2.79	IpAddress	accessible-for-notify	The secondary seed IP address to which the Mobility Domain has failed over. This object is used within notifications and is not accessible.
IP ntwsMobilityDomainPrimarySeedIp	1.3.6.1.4.1.45.6.1.2.80	IpAddress	accessible-for-notify	The primary seed IP address to which the Mobility Domain has failed back. This object is used within notifications and is not accessible.
NTW ntwsRFDetectClassificationReason	1.3.6.1.4.1.45.6.1.2.81	NtwsRFDetectClassificationReason	accessible-for-notify	Indicates the reason why a RF device is classified the way it is. This object is used within notifications and is not accessible.
STR ntwsConfigSaveFileName	1.3.6.1.4.1.45.6.1.2.82	DisplayString	accessible-for-notify	Display string listing the name of the file to which the running configuration was saved. This object is used within notifications and is not accessible.
NTW ntwsConfigSaveInitiatorType	1.3.6.1.4.1.45.6.1.2.83	NtwsConfigSaveInitiatorType	accessible-for-notify	Indicates the source that initiated a configuration save. This object is used within notifications and is not accessible.
IP ntwsConfigSaveInitiatorIp	1.3.6.1.4.1.45.6.1.2.84	IpAddress	accessible-for-notify	The IP address of the source that initiated a configuration save. This object is used within notifications and is not accessible.
STR ntwsConfigSaveInitiatorDetails	1.3.6.1.4.1.45.6.1.2.85	DisplayString	accessible-for-notify	Display string listing additional information regarding the source that initiated a configuration save, when available. This object is used within notifications and is not accessible.
C32 ntwsConfigSaveGeneration	1.3.6.1.4.1.45.6.1.2.86	Counter32	accessible-for-notify	Indicates the number of configuration changes since the last system boot. The generation count is used to track the number of times the running configuration has been changed due to administrative actions (set/clear), SNMP requests (SET), XML requests (e.g. WMS). This object is used within notifications and is not accessible.
NTW ntwsApNum	1.3.6.1.4.1.45.6.1.2.87	NtwsApNum	accessible-for-notify	The administratively assigned AP Number, unique on same AC (switch), regardless of how APs are attached to the AC. This object is used within notifications and is not accessible. Obsoletes ntwsApPortOrDapNum. For clarity, use this object to identify an AP since in 6.0 directly attached APs and DAPs were unified.
NTW ntwsRadioMode	1.3.6.1.4.1.45.6.1.2.88	NtwsRadioMode	accessible-for-notify	Indicates the administratively controlled Radio Mode (enabled/disabled/sentry). This object is used within notifications and is not accessible.
NTW ntwsMichaelMICFailureCause	1.3.6.1.4.1.45.6.1.2.89	NtwsMichaelMICFailureCause	accessible-for-notify	Indicates the Michael MIC Failure cause / who detected it. This object is used within notifications and is not accessible.
NTW ntwsClientAccessMode	1.3.6.1.4.1.45.6.1.2.90	NtwsClientAccessMode	accessible-for-notify	The client access mode (ap, wired). This object is used within notifications and is not accessible. Intended to replace ntwsClientAccessType. (In 6.0, direct- and network-attached APs were unified.)
NTW ntwsClientAuthorizationReason	1.3.6.1.4.1.45.6.1.2.91	NtwsClientAuthorizationReason	accessible-for-notify	Indicates the reason why client performed AAA authorization. This object is used within notifications and is not accessible.
U32 ntwsPhysPortNum	1.3.6.1.4.1.45.6.1.2.92	Unsigned32	accessible-for-notify	Physical Port Number on the AC. Zero means the port is unknown or not applicable (for example, when ntwsClientAccessMode = 'ap'). This object is used within notifications and is not accessible.
IP ntwsApMgrOldIp	1.3.6.1.4.1.45.6.1.2.93	IpAddress	accessible-for-notify	The IP address of the AP's former primary manager switch. This object is used within notifications and is not accessible.
IP ntwsApMgrNewIp	1.3.6.1.4.1.45.6.1.2.94	IpAddress	accessible-for-notify	The IP address of the AP's new primary manager switch. This address was formerly the AP's secondary backup link. This object is used within notifications and is not accessible.
NTW ntwsApMgrChangeReason	1.3.6.1.4.1.45.6.1.2.95	NtwsApMgrChangeReason	accessible-for-notify	Indicates the reason why the AP's primary manager changed. This object is used within notifications and is not accessible.
NTW ntwsClientClearedReason	1.3.6.1.4.1.45.6.1.2.96	NtwsClientClearedReason	accessible-for-notify	Indicates the reason why client was cleared. This object is used within notifications and is not accessible.
NTW ntwsMobilityDomainResiliencyStatus	1.3.6.1.4.1.45.6.1.2.97	NtwsMobilityDomainResiliencyStatus	accessible-for-notify	Indicates the current resilient capacity status for a mobility domain. This object is used within notifications and is not accessible.
U32 ntwsClientSessionElapsedSeconds	1.3.6.1.4.1.45.6.1.2.98	Unsigned32	accessible-for-notify	Indicates the time in seconds elapsed since the start of the Client Session. This object is used within notifications and is not accessible.
NTW ntwsRadioChannelWidth	1.3.6.1.4.1.45.6.1.2.99	NtwsRadioChannelWidth	accessible-for-notify	Indicates the administratively controlled Channel Width (20MHz/40MHz). This object is used within notifications and is not accessible.
NTW ntwsRadioMimoState	1.3.6.1.4.1.45.6.1.2.100	NtwsRadioMimoState	accessible-for-notify	Indicates the Radio MIMO State, as seen by the AC (1x1/2x3/3x3). This object is used within notifications and is not accessible.
NTW ntwsClientRadioType	1.3.6.1.4.1.45.6.1.2.101	NtwsRadioType	accessible-for-notify	Indicates the Client Radio Type, as detected by an attached AP and reported to the AC. This object is used within notifications and is not accessible.
NTW ntwsRFDetectXmtrRadioType	1.3.6.1.4.1.45.6.1.2.102	NtwsRadioType	accessible-for-notify	Indicates the Radio Type of the Transmitter, as detected by an attached AP and reported to the AC. The Transmitter may be a wireless client or an AP. This object is used within notifications and is not accessible.
NTW ntwsRFDetectXmtrCryptoType	1.3.6.1.4.1.45.6.1.2.103	NtwsCryptoType	accessible-for-notify	Indicates the Crypto Type used by the Transmitter, as detected by an attached AP and reported to the AC. This object is used within notifications and is not accessible.
NTW ntwsClusterFailureReason	1.3.6.1.4.1.45.6.1.2.104	NtwsClusterFailureReason	accessible-for-notify	Indicates the reason why cluster configuration failed to apply. This object is used within notifications and is not accessible.
STR ntwsClusterFailureDescription	1.3.6.1.4.1.45.6.1.2.105	DisplayString	accessible-for-notify	Display string for describing the cluster configuration failure cause. This object is used within notifications and is not accessible.
ntwsTrapMib	1.3.6.1.4.1.45.6.1.4.1			Notifications emitted by Nortel Networks wireless switches. AP = Access Point; AC = Access Controller (wireless switch), the device that runs a SNMP Agent implementing this MIB. Copyright 2008 Nortel Networks. All rights reserved. This Nortel Networks SNMP Management Information Base Specification (Specification) embodies Nortel Networks' confidential and proprietary intellectual property. This Specification is supplied 'AS IS' and Nortel Networks makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
ntwsTrapsV2	1.3.6.1.4.1.45.6.1.5.0
NTF ntwsDeviceFailTrap	1.3.6.1.4.1.45.6.1.5.0.1			The device has a failure indication
NTF ntwsDeviceOkayTrap	1.3.6.1.4.1.45.6.1.5.0.2			The device has recovered
NTF ntwsPoEFailTrap	1.3.6.1.4.1.45.6.1.5.0.3			PoE has failed on the indicated port
NTF ntwsApTimeoutTrap	1.3.6.1.4.1.45.6.1.5.0.4			The AP entering the AC at port ntwsPortNum with MAC ntwsRadioMacAddress and of the access type (ap or dap) has not responded. Replaced by ntwsApNonOperStatusTrap2, with ntwsApTransition = 'timeout'.
NTF ntwsAPBootTrap	1.3.6.1.4.1.45.6.1.5.0.5			The AP entering the AC at port ntwsPortNum with MAC ntwsRadioMacAddress and of the access type (ap or dap) has booted. Replaced by ntwsApNonOperStatusTrap2, with ntwsApTransition = 'bootSuccess'.
NTF ntwsMobilityDomainJoinTrap	1.3.6.1.4.1.45.6.1.5.0.6			The mobility domain member has received an UP notice from the remote address.
NTF ntwsMobilityDomainTimeoutTrap	1.3.6.1.4.1.45.6.1.5.0.7			The mobility domain member has declared the remote address to be DOWN.
NTF ntwsMpMichaelMICFailure	1.3.6.1.4.1.45.6.1.5.0.8			Two Michael MIC failures were seen within 60 seconds of each other. Obsoleted by ntwsMichaelMICFailure.
NTF ntwsRFDetectRogueAPTrap	1.3.6.1.4.1.45.6.1.5.0.9			This trap is sent when RF detection finds a rogue AP. XmtrMacAddr is the radio MAC address from the beacon. ListenerListInfo is a display string of a list of listener information. Obsoleted by ntwsRFDetectRogueDeviceTrap2.
NTF ntwsRFDetectAdhocUserTrap	1.3.6.1.4.1.45.6.1.5.0.10			This trap is sent when RF detection sweep finds a ad-hoc user. ntwsRFDetectXmtrMacAddr is the MAC address of the ad-hoc user. ntwsRFDetectListenerListInfo is a display string of a list of listener information.
NTF ntwsRFDetectRogueDisappearTrap	1.3.6.1.4.1.45.6.1.5.0.11			This trap is sent when a rogue has disappeared. Obsoleted by ntwsRFDetectRogueDeviceDisappearTrap.
NTF ntwsClientAuthenticationFailureTrap	1.3.6.1.4.1.45.6.1.5.0.12			This trap is sent if a client authentication fails.
NTF ntwsClientAuthorizationFailureTrap	1.3.6.1.4.1.45.6.1.5.0.13			This trap is sent if a client authorization fails.
NTF ntwsClientAssociationFailureTrap	1.3.6.1.4.1.45.6.1.5.0.14			This trap is sent if a client association fails.
NTF ntwsClientAuthorizationSuccessTrap	1.3.6.1.4.1.45.6.1.5.0.15			This trap is sent when a client authorizes. Obsoleted by ntwsClientAuthorizationSuccessTrap4.
NTF ntwsClientDeAssociationTrap	1.3.6.1.4.1.45.6.1.5.0.16			This trap is sent if a client de-association occurred.
NTF ntwsClientRoamingTrap	1.3.6.1.4.1.45.6.1.5.0.17			This trap is sent if a client roams from one location to another.
NTF ntwsAutoTuneRadioPowerChangeTrap	1.3.6.1.4.1.45.6.1.5.0.18			This trap is sent if a radio's power level has changed based on auto-tune.
NTF ntwsAutoTuneRadioChannelChangeTrap	1.3.6.1.4.1.45.6.1.5.0.19			This trap is sent if a radio's channel has changed based on auto-tune.
NTF ntwsCounterMeasureStartTrap	1.3.6.1.4.1.45.6.1.5.0.20			This trap is sent when counter measures are started against a rogue. ntwsRFDetectXmtrMacAddr is the mac address of the rogue we are doing counter measures against. ntwsRadioMACAddress identifies the radio performing the countermeasures.
NTF ntwsCounterMeasureStopTrap	1.3.6.1.4.1.45.6.1.5.0.21			This trap is sent when counter measures are stopped against a rogue. ntwsRFDetectXmtrMacAddr is the mac address of the rogue we were doing counter measures against. ntwsRadioMACAddress identifies the radio performing the countermeasures.
NTF ntwsClientDot1xFailureTrap	1.3.6.1.4.1.45.6.1.5.0.22			This trap is sent if a client failed 802.1X.
NTF ntwsClientClearedTrap	1.3.6.1.4.1.45.6.1.5.0.23			This trap is sent when a client session is cleared. Obsoleted by ntwsClientClearedTrap2.
NTF ntwsClientAuthorizationSuccessTrap2	1.3.6.1.4.1.45.6.1.5.0.24			This trap is sent when a client authorizes. Obsoleted by ntwsClientAuthorizationSuccessTrap4.
NTF ntwsRFDetectSpoofedMacAPTrap	1.3.6.1.4.1.45.6.1.5.0.25			This trap is sent when RF detection finds an AP using the MAC of the listener. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by ntwsRFDetectDoSTrap and ntwsRFDetectRogueDeviceTrap2. One of the two traps will be sent depending on the type of AP MAC spoofing detected.
NTF ntwsRFDetectSpoofedSsidAPTrap	1.3.6.1.4.1.45.6.1.5.0.26			This trap is sent when RF detection finds an AP using the SSID of the listener, and the AP is not in the mobility domain. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by ntwsRFDetectRogueDeviceTrap2 and ntwsRFDetectSuspectDeviceTrap2. One of the two traps will be sent, depending on RF detection classification rules.
NTF ntwsRFDetectDoSTrap	1.3.6.1.4.1.45.6.1.5.0.27			This trap is sent when RF detection finds a denial of service (DoS) occurring. ntwsRFDetectDoSType specifies the type of DoS. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectListenerListInfo is a display string of a list of listener information.
NTF ntwsRFDetectClientViaRogueWiredAPTrap	1.3.6.1.4.1.45.6.1.5.0.28			This trap is sent when a client is detected that connected via a rogue AP that is attached to a wired port. ntwsSourceWsIp is the IP address of the AC (switch) with the wired port. ntwsPortNum is the port on the AC. ntwsClientVLANid is the VLAN ID of the client's traffic. ntwsClientVLANtag is the VLAN tag of the client's traffic. ntwsRFDetectXmtrMacAddr is the MAC address of the client. ntwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by ntwsRFDetectClientViaRogueWiredAPTrap3.
NTF ntwsRFDetectInterferingRogueAPTrap	1.3.6.1.4.1.45.6.1.5.0.29			This trap is sent when RF detection finds an interfering rogue AP. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by ntwsRFDetectSuspectDeviceTrap2.
NTF ntwsRFDetectInterferingRogueDisappearTrap	1.3.6.1.4.1.45.6.1.5.0.30			This trap is sent when an interfering rogue has disappeared. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. Obsoleted by ntwsRFDetectSuspectDeviceDisappearTrap.
NTF ntwsRFDetectUnAuthorizedSsidTrap	1.3.6.1.4.1.45.6.1.5.0.31			This trap is sent when RF detection finds use of an unauthorized SSID. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by ntwsRFDetectRogueDeviceTrap2 and ntwsRFDetectSuspectDeviceTrap2. One of the two traps will be sent if the device having an unauthorized SSID is classified as rogue or suspect because of this.
NTF ntwsRFDetectUnAuthorizedOuiTrap	1.3.6.1.4.1.45.6.1.5.0.32			This trap is sent when RF detection finds use of an unauthorized OUI. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by ntwsRFDetectRogueDeviceTrap2 and ntwsRFDetectSuspectDeviceTrap2. One of the two traps will be sent if the device having an unauthorized OUI is classified as rogue or suspect because of this.
NTF ntwsRFDetectUnAuthorizedAPTrap	1.3.6.1.4.1.45.6.1.5.0.33			This trap is sent when RF detection finds operation of an unauthorized AP. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by ntwsRFDetectRogueDeviceTrap2.
NTF ntwsDAPConnectWarningTrap	1.3.6.1.4.1.45.6.1.5.0.34			A DAP, tried to connect to the AC. ntwsDeviceModel provides the model of the DAP. ntwsDeviceSerNum provides the serial number of the DAP. ntwsRsaPubKeyFingerPrint provides the computed fingerprint of the DAP. ntwsDAPconnectWarningType provides the type of connect warning. Replaced by ntwsApNonOperStatusTrap2, with ntwsApTransition = 'connectFail'.
NTF ntwsRFDetectDoSPortTrap	1.3.6.1.4.1.45.6.1.5.0.35			This trap is sent when RF detection finds a denial of service (DoS) occurring. This has port and AP info instead of 'Listener info'. ntwsRFDetectDoSType specifies the type of DoS. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsClientAccessType specifies whether wired, AP, or DAP. ntwsPortNum (for wired or AP), the port that is used. ntwsDAPNum (for a DAP), the ID of the DAP.
NTF ntwsMpMichaelMICFailure2	1.3.6.1.4.1.45.6.1.5.0.36			Two Michael MIC failures were seen within 60 seconds of each other. Object ntwsClientMACAddress is the source of the first failure, and object ntwsClientMACAddress2 source of the second failure. Obsoleted by ntwsMichaelMICFailure.
NTF ntwsApNonOperStatusTrap	1.3.6.1.4.1.45.6.1.5.0.37			This trap is sent when the AP changes state and the new one is a non-operational state. Obsoleted by ntwsApNonOperStatusTrap2.
NTF ntwsApOperRadioStatusTrap	1.3.6.1.4.1.45.6.1.5.0.38			This trap is sent when the Radio changes state. It also contains aggregate information about the AP in operational state - security level and service availability. Obsoleted by ntwsApOperRadioStatusTrap3.
NTF ntwsClientIpAddrChangeTrap	1.3.6.1.4.1.45.6.1.5.0.39			This trap is sent when a client's IP address changes. The most likely case for this is when the client first connects to the network.
NTF ntwsClientAssociationSuccessTrap	1.3.6.1.4.1.45.6.1.5.0.40			This trap is sent if a client association succeeds. WARNING: DO NOT enable it in normal use. It may impair switch performance! Only recommended for debugging network issues.
NTF ntwsClientAuthenticationSuccessTrap	1.3.6.1.4.1.45.6.1.5.0.41			This trap is sent if a client authentication succeeds.
NTF ntwsClientDeAuthenticationTrap	1.3.6.1.4.1.45.6.1.5.0.42			This trap is sent if a client de-authentication occured.
NTF ntwsRFDetectBlacklistedTrap	1.3.6.1.4.1.45.6.1.5.0.43			This trap is sent if an association, re-association or de-association request (packet) is detected from a blacklisted transmitter (identified by MAC: 'ntwsRFDetectXmtrMacAddr'). If 'ntwsBlacklistingCause' is 'configured', then 'ntwsBlacklistingRemainingTime' will be zero, meaning indefinite time (depending on administrative actions on the Black List). Otherwise, 'ntwsBlacklistingRemainingTime' will indicate the time in seconds until this transmitter's requests could be allowed.
NTF ntwsRFDetectClientViaRogueWiredAPTrap2	1.3.6.1.4.1.45.6.1.5.0.44			This trap is sent when a client is detected that connected via a rogue AP that is attached to a wired port. ntwsSourceWsIp is the IP address of the AC (switch) with the wired port. ntwsPortNum is the port on the AC. ntwsClientVLANid is the VLAN ID of the client's traffic. ntwsClientVLANtag is the VLAN tag of the client's traffic. ntwsRFDetectXmtrMacAddr is the MAC address of the client. ntwsRFDetectListenerListInfo is a display string of a list of listener information. ntwsRFDetectRogueAPMacAddr is the MAC address of the Rogue AP (wired) the client is connected to. Obsoleted by ntwsRFDetectClientViaRogueWiredAPTrap3.
NTF ntwsRFDetectAdhocUserDisappearTrap	1.3.6.1.4.1.45.6.1.5.0.45			This trap is sent when RF detection sweep finds that an ad-hoc user disappeared. ntwsRFDetectXmtrMacAddr is the MAC address of the ad-hoc user.
NTF ntwsApRejectLicenseExceededTrap	1.3.6.1.4.1.45.6.1.5.0.46			This trap is sent when an AC (wireless switch) receives a packet from an inactive AP and attaching that AP would make the AC exceed the maximum (licensed) number of active APs.
NTF ntwsClientDynAuthorChangeSuccessTrap	1.3.6.1.4.1.45.6.1.5.0.47			This trap is sent when the authorization attributes for a user are dynamically changed by an authorized dynamic authorization client.
NTF ntwsClientDynAuthorChangeFailureTrap	1.3.6.1.4.1.45.6.1.5.0.48			This trap is sent if a change of authorization request sent by an authorized dynamic authorization client is unsuccessful.
NTF ntwsClientDisconnectTrap	1.3.6.1.4.1.45.6.1.5.0.49			This trap is sent when a client session is terminated administratively.
NTF ntwsMobilityDomainFailOverTrap	1.3.6.1.4.1.45.6.1.5.0.50			This trap is sent when the Mobility Domain fails over to the secondary seed.
NTF ntwsMobilityDomainFailBackTrap	1.3.6.1.4.1.45.6.1.5.0.51			This trap is sent when the Mobility Domain fails back to the primary seed.
NTF ntwsRFDetectRogueDeviceTrap	1.3.6.1.4.1.45.6.1.5.0.52			This trap is sent when RF detection finds a rogue device. XmtrMacAddr is the radio MAC address from the beacon. ListenerListInfo is a display string of a list of listener information. ClassificationReason indicates the reason why the device is classified as rogue. Obsoleted by ntwsRFDetectRogueDeviceTrap2.
NTF ntwsRFDetectRogueDeviceDisappearTrap	1.3.6.1.4.1.45.6.1.5.0.53			This trap is sent when a rogue device has disappeared. This trap obsoletes the ntwsRFDetectRogueDisappearTrap.
NTF ntwsRFDetectSuspectDeviceTrap	1.3.6.1.4.1.45.6.1.5.0.54			This trap is sent when RF detection finds a suspect device. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectListenerListInfo is a display string of a list of listener information. ClassificationReason indicates the reason why the device is classified as suspect. Obsoleted by ntwsRFDetectSuspectDeviceTrap2.
NTF ntwsRFDetectSuspectDeviceDisappearTrap	1.3.6.1.4.1.45.6.1.5.0.55			This trap is sent when a suspect device has disappeared. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. This trap obsoletes the ntwsRFDetectInterferingRogueDisappearTrap.
NTF ntwsRFDetectClientViaRogueWiredAPTrap3	1.3.6.1.4.1.45.6.1.5.0.56			This trap is sent when a client is detected that connected via a rogue AP that is attached to a wired port. ntwsSourceWsIp is the IP address of the AC (switch) with the wired port. ntwsPortNum is the port on the AC. ntwsClientVLANid is the VLAN ID of the client's traffic. ntwsClientVLANtag is the VLAN tag of the client's traffic. ntwsRFDetectXmtrMacAddr is the MAC address of the client. ntwsRFDetectListenerListInfo is a display string of a list of listener information. ntwsRFDetectRogueAPMacAddr is the MAC address of the Rogue AP (wired) the client is connected to. ClassificationReason indicates the reason why the AP is classified as rogue. This trap obsoletes the ntwsRFDetectClientViaRogueWiredAPTrap and ntwsRFDetectClientViaRogueWiredAPTrap2.
NTF ntwsRFDetectClassificationChangeTrap	1.3.6.1.4.1.45.6.1.5.0.57			This trap is sent when RF detection classification rules change.
NTF ntwsConfigurationSavedTrap	1.3.6.1.4.1.45.6.1.5.0.58			This trap is sent when the running configuration of the switch is written to a configuration file.
NTF ntwsApNonOperStatusTrap2	1.3.6.1.4.1.45.6.1.5.0.59			This trap is sent when the AP changes state and the new one is a non-operational state. Obsoletes ntwsApNonOperStatusTrap.
NTF ntwsApOperRadioStatusTrap2	1.3.6.1.4.1.45.6.1.5.0.60			This trap is sent when the Radio changes state. It also contains aggregate information about the AP in operational state - security level and service availability. Obsoleted by ntwsApOperRadioStatusTrap3.
NTF ntwsMichaelMICFailure	1.3.6.1.4.1.45.6.1.5.0.61			Two Michael MIC failures were seen within 60 seconds of each other. Object ntwsClientMACAddress indicates the source of the first failure, and object ntwsClientMACAddress2 indicates the source of the second failure. Service is interrupted for 60 seconds on the radio due to TKIP countermeasures having commenced. The radio is identified by ntwsApNum and ntwsAPRadioNum. An alternative way to identify the radio is ntwsRadioMACAddress. Obsoletes ntwsMpMichaelMICFailure and ntwsMpMichaelMICFailure2.
NTF ntwsClientAuthorizationSuccessTrap3	1.3.6.1.4.1.45.6.1.5.0.62			This trap is sent when a client authorizes. If ntwsClientAccessMode = 'ap': ntwsApNum, ntwsAPRadioNum, ntwsRadioSSID identify the AP/radio/BSS providing wireless service to this client at the time this trap was sent. If ntwsClientAccessMode = 'wired': ntwsPhysPortNum identifies the physical port on the AC used by this wired-auth client. Obsoleted by ntwsClientAuthorizationSuccessTrap4.
NTF ntwsApManagerChangeTrap	1.3.6.1.4.1.45.6.1.5.0.63			This trap is sent when the AP's secondary link becomes its primary link.
NTF ntwsClientClearedTrap2	1.3.6.1.4.1.45.6.1.5.0.64			This trap is sent when a client session is cleared. Obsoletes ntwsClientClearedTrap.
NTF ntwsMobilityDomainResiliencyStatusTrap	1.3.6.1.4.1.45.6.1.5.0.65			This trap is sent by a mobility domain seed to announce changes in resilient capacity status.
NTF ntwsApOperRadioStatusTrap3	1.3.6.1.4.1.45.6.1.5.0.66			This trap is sent when the Radio changes state. It also contains aggregate information about the AP in operational state - security level and service availability. Obsoletes ntwsApOperRadioStatusTrap and ntwsApOperRadioStatusTrap2.
NTF ntwsClientAuthorizationSuccessTrap4	1.3.6.1.4.1.45.6.1.5.0.67			This trap is sent when a client authorizes. If ntwsClientAccessMode = 'ap': ntwsApNum, ntwsAPRadioNum, ntwsRadioSSID identify the AP/radio/BSS providing wireless service to this client at the time this trap was sent; ntwsClientRadioType gives the type of radio used by this client. If ntwsClientAccessMode = 'wired': ntwsPhysPortNum identifies the physical port on the AC used by this wired-auth client. Obsoletes ntwsClientAuthorizationSuccessTrap, ntwsClientAuthorizationSuccessTrap2, ntwsClientAuthorizationSuccessTrap3.
NTF ntwsRFDetectRogueDeviceTrap2	1.3.6.1.4.1.45.6.1.5.0.68			This trap is sent when RF detection finds a rogue device. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectXmtrRadioType indicates the Type of Radio used by the transmitter (rogue device). ntwsRFDetectXmtrCryptoType indicates the Type of Crypto used by the transmitter (rogue device). ntwsRFDetectListenerListInfo is a display string of a list of listener information. ntwsRFDetectClassificationReason indicates the reason why the device is classified as rogue. Obsoletes ntwsRFDetectRogueAPTrap, ntwsRFDetectUnAuthorizedAPTrap, ntwsRFDetectRogueDeviceTrap.
NTF ntwsRFDetectSuspectDeviceTrap2	1.3.6.1.4.1.45.6.1.5.0.69			This trap is sent when RF detection finds a suspect device. ntwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. ntwsRFDetectXmtrRadioType indicates the Type of Radio used by the transmitter (suspect device). ntwsRFDetectXmtrCryptoType indicates the Type of Crypto used by the transmitter (suspect device). ntwsRFDetectListenerListInfo is a display string of a list of listener information. ntwsRFDetectClassificationReason indicates the reason why the device is classified as suspect. Obsoletes ntwsRFDetectInterferingRogueAPTrap, ntwsRFDetectSuspectDeviceTrap.
NTF ntwsClusterFailureTrap	1.3.6.1.4.1.45.6.1.5.0.70			This trap is sent when the cluster configuration failed to apply. If ntwsClusterFailureReason = 'validation-error': The validation error is reported by the receiving end of the configuration updates. The receiving end can be any AC (switch) in the mobility domain: member, secondary seed or primary seed. - Primary seed will be the receiving end of configuration updates when Primary seed is joining the cluster and Secondary seed has preempt mode enabled. - Both Secondary seed and member will be at the receiving end when Primary seed is active.

RFC description

Nortel wireless switch MIB for access point and client notifications and traps.

Start monitoring Nortel NTWS wireless LAN controller and managed Access Points (fault/event notifications) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NTWS-TRAP-MIB

What Is NTWS-TRAP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description