All MIBs › NNC-ATM-STATISTICS-MIB
Organization: Newbridge Networks Corporation
Last Updated: 1998-07-21
Category: ATM
Description: Monitors Newbridge Networks ATM interface traffic statistics including cell rates and utilization.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is NNC-ATM-STATISTICS-MIB?
NNC-ATM-STATISTICS-MIB is a Newbridge Networks proprietary MIB for ATM switching equipment that provides performance statistics at the virtual path link (VPL) and virtual channel link (VCL) circuit layers. It exposes tiered time-series tables — 15-minute current/interval and 1-hour current/interval — plus generic stat and stat-counter tables for both VPL and VCL circuits, covering traffic volume and utilization at the ATM circuit level. As a performance-monitoring MIB it is used to watch bandwidth utilization and traffic trends on individual ATM virtual circuits rather than chassis hardware health, helping detect circuit-level congestion or abrupt traffic pattern changes. It relies on the same per-interface indexing conventions used elsewhere in ATM MIBs (e.g., ATM-MIB) to associate VPL/VCL identifiers with physical interfaces. It was typically deployed on legacy Newbridge (later Alcatel) ATM switches in carrier and enterprise networks needing granular per-circuit traffic accounting, relying on NNC-ATM-STATISTICS-MIB SNMP monitoring to track VPL/VCL utilization trends.
IPNetwork Monitor allows you to monitor SNMP objects defined in NNC-ATM-STATISTICS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Newbridge Networks / Alcatel ATM switch
Monitoring Examples
An operator polls nncAtmVplStatCounterTable, keyed by nncAtmVplStatCounterIndex, to read nncAtmVplStatCounterValue for a specific virtual path, and similarly reads nncAtmVclStatCounterTable's nncAtmVclStatCounterValue for a virtual channel, comparing cell counts against provisioned bandwidth; a VCL stat counter value approaching the circuit's contracted rate signals imminent congestion on that virtual channel.
What Can Be Monitored
- ATM VPL traffic statistics
- ATM VCL traffic statistics
- 15-minute and 1-hour interval counters
- per-circuit stat counter values
This MIB depends on
Related MIBs
Imported Objects
From ATM-MIB
| atmVclVci | OBJECT-TYPE |
| atmVclVpi | OBJECT-TYPE |
| atmVplVpi | OBJECT-TYPE |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From NNC-INTERVAL-STATISTICS-TC-MIB
| NncExtAbsIntvlNumberType | |
| NncExtIntvlStateType | |
| NncExtRelIntvlNumberType |
From NNCGNI0001-SMI
| NncExtCounter64 | |
| nncExtensions | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter64 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| RowStatus |
How to Use in IPNetwork Monitor
Example using nncVpa15MinCurrentClp0And1OutCells OID:
Select a Newbridge Networks/Alcatel ATM switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type nncVpa15MinCurrentClp0And1OutCells into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the total CLP0 and CLP1 cells transmitted on all constituent VCs of a particular VPA. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| nncAtmStatistics | 1.3.6.1.4.1.123.3.29 | This module contains definitions for performance monitoring of the ATM layer and it's circuits. This MIB module contains the following tables: ATM VPL 15 Minute Current Table ATM VPL 15 Minute Interval Table ATM VPL 1 Hour Current Table ATM VPL 1 Hour Interval Table ATM VPL Stat Table ATM VPL Stat Counter Table ATM VCL 15 Minute Current Table ATM VCL 15 Minute Interval Table ATM VCL 1 Hour Current Table ATM VCL 1 Hour Interval Table ATM VCL Stat Table ATM VCL Stat Counter Table nncDepthOfHistoricalStrata These tables are heavily influenced by the definition of VPL/VCL described in rfc1695, and by the statistic table definitions described for Sonet in rfc1595. The number of intervals supported is dependent upon resource availibility on any given product, but should nominally be 32. To avoid building in massive amounts of storage, some products may adopt a bulk collection scheme. Intervals: Statistics on the performance of VPL/VCLs are collected over a historical stratum of up to a maximum of M intervals. The value of M is a function of a product's storage capability. The intervals can be either 15 minutes or 1 hour and are aligned to the quarter or one hour, respectively, of a wall clock. The current interval spans back to the last 15 minute or 1 hour tick on the wall clock. Continuing along the timeline from that point is the most recently completed interval and has an index of 1. The previous interval has an index of 2 and so on. Note that the oldest interval may be incomplete since the statistic collection may have been enabled offset to the quarter or one hour tick. t 0 -1i -2i -3i ===========|===========|===========|===========|=========== current N = 1 N = 2 N = 3 N = 4 ... N = M interval Counters: The following is understood for each counter in this MIB: - OAM cells are included in counts - idle and unassigned cells are not counted - valid cells are those that have passed HEC and have assigned VPI/VCI - admitted cells have a connection This module also contains definitions for performance monitoring of Virtual Path Aggregation (VPA) - also known as VCC to VPC Traffic Aggregation - and implemented as Shaped Trunk Group. Only egress VPA statistics are provided. The following tables have been added : ATM VPA Short (15 minutes) Current Table ATM VPA Short (15 Minutes) Interval Table ATM VPA Long (1 Hour) Current Table ATM VPA Long (1 Hour) Interval Table Intervals: two 15-minute intervals are provided : current and previous two 1-hour intervals are provided : current and previous. | ||
| nncAtmStatisticsObjects | 1.3.6.1.4.1.123.3.29.1 | |||
| nncVpl15MinCurrentTable | 1.3.6.1.4.1.123.3.29.1.1 | not-accessible | The nncVpl15MinCurrentTable contains objects for monitoring the performance of a VPL during the current 15 minute interval. | |
| nncVpl15MinCurrentEntry | 1.3.6.1.4.1.123.3.29.1.1.1 | not-accessible | An entry in the 15 minute current statistics table. Each conceptual row contains current statistics for a particular VPL. | |
| NUM nncVpl15MinCurrentState | 1.3.6.1.4.1.123.3.29.1.1.1.1 | NncExtIntvlStateType | read-only | The state of the current interval. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| NUM nncVpl15MinCurrentAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.1.1.2 | NncExtAbsIntvlNumberType | read-only | The absolute interval number of this interval. |
| NUM nncVpl15MinCurrentClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.1.1.3 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVpl15MinCurrentClp0InCells | 1.3.6.1.4.1.123.3.29.1.1.1.4 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0, including those with header errors corrected. |
| NUM nncVpl15MinCurrentDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.1.1.5 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl15MinCurrentDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.1.1.6 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl15MinCurrentTaggedInCells | 1.3.6.1.4.1.123.3.29.1.1.1.7 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl15MinCurrentClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.1.1.8 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0 or 1. |
| NUM nncVpl15MinCurrentClp0OutCells | 1.3.6.1.4.1.123.3.29.1.1.1.9 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0. |
| nncVpl15MinIntervalTable | 1.3.6.1.4.1.123.3.29.1.2 | not-accessible | The nncVpl15MinIntervalTable contains objects for monitoring the performance of a virtual path link over a historical stratum of M 15 minute intervals. | |
| nncVpl15MinIntervalEntry | 1.3.6.1.4.1.123.3.29.1.2.1 | not-accessible | An entry in the 15 minute interval statistics table. Each conceptual row contains statistics for a particular VPL and interval. | |
| NUM nncVpl15MinIntervalNumber | 1.3.6.1.4.1.123.3.29.1.2.1.1 | NncExtRelIntvlNumberType | not-accessible | The interval number (N) of the statistics in this row. |
| NUM nncVpl15MinIntervalState | 1.3.6.1.4.1.123.3.29.1.2.1.2 | NncExtIntvlStateType | read-only | The state of the interval represented by this row. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| NUM nncVpl15MinIntervalAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.2.1.3 | NncExtAbsIntvlNumberType | read-only | The absolute interval number of this interval. |
| NUM nncVpl15MinIntervalClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.2.1.4 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVpl15MinIntervalClp0InCells | 1.3.6.1.4.1.123.3.29.1.2.1.5 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0, including those with header errors corrected. |
| NUM nncVpl15MinIntervalDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.2.1.6 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl15MinIntervalDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.2.1.7 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl15MinIntervalTaggedInCells | 1.3.6.1.4.1.123.3.29.1.2.1.8 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl15MinIntervalClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.2.1.9 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0 or 1. |
| NUM nncVpl15MinIntervalClp0OutCells | 1.3.6.1.4.1.123.3.29.1.2.1.10 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0. |
| nncVpl1HourCurrentTable | 1.3.6.1.4.1.123.3.29.1.3 | not-accessible | The nncVpl1HourCurrentTable contains objects for monitoring the performance of a VPL during the current 1 hour interval. | |
| nncVpl1HourCurrentEntry | 1.3.6.1.4.1.123.3.29.1.3.1 | not-accessible | An entry in the 1 hour current statistics table. Each conceptual row contains current statistics for a particular VPL. By default, 1 Hour statistics are not gathered. In order to enable gathering of these statistics, a row must be created. The semantics of nncVpl1HourCurrentRowStatus is the same as the definition of RowStatus in rfc1443 with the following constraints. 1. Creation is done in one step, that is, by setting the nncVpl1HourCurrentRowStatus column to createAndGo. Setting the column to createAndWait will return wrongValue. 2. The VPI specified in the instance must be an endpoint that is currently used in a VPL otherwise the agent will return return inconsistentValue and no row is created. 3. If the maximum number of rows (an agent limitation) has been reached, resourceUnavailable is returned and no row is created. 4. Creation of a current row will also enable the corresponding interval table whose rows will be created when intervals are completed. 5. Statistics collection is disabled by setting the column to destroy. This will also remove all corresponding rows in the interval table. | |
| NUM nncVpl1HourCurrentState | 1.3.6.1.4.1.123.3.29.1.3.1.1 | NncExtIntvlStateType | read-only | The state of the current interval. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| NUM nncVpl1HourCurrentAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.3.1.2 | NncExtAbsIntvlNumberType | read-only | The absolute interval number of this interval. |
| NUM nncVpl1HourCurrentClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.3.1.3 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVpl1HourCurrentClp0InCells | 1.3.6.1.4.1.123.3.29.1.3.1.4 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0, including those with header errors corrected. |
| NUM nncVpl1HourCurrentDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.3.1.5 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl1HourCurrentDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.3.1.6 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl1HourCurrentTaggedInCells | 1.3.6.1.4.1.123.3.29.1.3.1.7 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl1HourCurrentClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.3.1.8 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0 or 1. |
| NUM nncVpl1HourCurrentClp0OutCells | 1.3.6.1.4.1.123.3.29.1.3.1.9 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0. |
| ROW nncVpl1HourCurrentRowStatus | 1.3.6.1.4.1.123.3.29.1.3.1.10 | RowStatus | read-write | This object is used to create and delete rows in this table. The following sets are invalid: createAndWait, active, and notInService. Such sets will return wrongValue. |
| nncVpl1HourIntervalTable | 1.3.6.1.4.1.123.3.29.1.4 | not-accessible | The nncVpl1HourIntervalTable contains objects for monitoring the performance of a virtual path link over a historical stratum of M 1 hour intervals. | |
| nncVpl1HourIntervalEntry | 1.3.6.1.4.1.123.3.29.1.4.1 | not-accessible | An entry in the 1 hour interval statistics table. Each conceptual row contains statistics for a particular VPL and interval. These rows are automatically created if there is a corresponding entry in the 1 hour current table. | |
| NUM nncVpl1HourIntervalNumber | 1.3.6.1.4.1.123.3.29.1.4.1.1 | NncExtRelIntvlNumberType | not-accessible | The interval number (N) of the statistics in this row. |
| NUM nncVpl1HourIntervalState | 1.3.6.1.4.1.123.3.29.1.4.1.2 | NncExtIntvlStateType | read-only | The state of the interval represented by this row. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| NUM nncVpl1HourIntervalAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.4.1.3 | NncExtAbsIntvlNumberType | read-only | The absolute interval number of this interval. |
| NUM nncVpl1HourIntervalClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.4.1.4 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVpl1HourIntervalClp0InCells | 1.3.6.1.4.1.123.3.29.1.4.1.5 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0, including those with header errors corrected. |
| NUM nncVpl1HourIntervalDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.4.1.6 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl1HourIntervalDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.4.1.7 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl1HourIntervalTaggedInCells | 1.3.6.1.4.1.123.3.29.1.4.1.8 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVpl1HourIntervalClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.4.1.9 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0 or 1. |
| NUM nncVpl1HourIntervalClp0OutCells | 1.3.6.1.4.1.123.3.29.1.4.1.10 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0. |
| nncVcl15MinCurrentTable | 1.3.6.1.4.1.123.3.29.1.5 | not-accessible | The nncVcl15MinCurrentTable contains objects for monitoring the performance of a VCL during the current 15 minute interval. | |
| nncVcl15MinCurrentEntry | 1.3.6.1.4.1.123.3.29.1.5.1 | not-accessible | An entry in the 15 minute current statistics table. Each conceptual row contains current statistics for a particular VCL. | |
| NUM nncVcl15MinCurrentState | 1.3.6.1.4.1.123.3.29.1.5.1.1 | NncExtIntvlStateType | read-only | The state of the current interval. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| NUM nncVcl15MinCurrentAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.5.1.2 | NncExtAbsIntvlNumberType | read-only | The absolute interval number of this interval. |
| NUM nncVcl15MinCurrentClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.5.1.3 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVcl15MinCurrentClp0InCells | 1.3.6.1.4.1.123.3.29.1.5.1.4 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0, including those with header errors corrected. |
| NUM nncVcl15MinCurrentDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.5.1.5 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl15MinCurrentDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.5.1.6 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl15MinCurrentTaggedInCells | 1.3.6.1.4.1.123.3.29.1.5.1.7 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl15MinCurrentClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.5.1.8 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VCL with CLP=0 or 1. |
| NUM nncVcl15MinCurrentClp0OutCells | 1.3.6.1.4.1.123.3.29.1.5.1.9 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VCL with CLP=0. |
| nncVcl15MinIntervalTable | 1.3.6.1.4.1.123.3.29.1.6 | not-accessible | The nncVcl15MinIntervalTable contains objects for monitoring the performance of a virtual channel link over a historical stratum of M 15 minute intervals. | |
| nncVcl15MinIntervalEntry | 1.3.6.1.4.1.123.3.29.1.6.1 | not-accessible | An entry in the 15 minute interval statistics table. Each conceptual row contains statistics for a particular VCL and interval. | |
| NUM nncVcl15MinIntervalNumber | 1.3.6.1.4.1.123.3.29.1.6.1.1 | NncExtRelIntvlNumberType | not-accessible | The interval number (N) of the statistics in this row. |
| NUM nncVcl15MinIntervalState | 1.3.6.1.4.1.123.3.29.1.6.1.2 | NncExtIntvlStateType | read-only | The state of the interval represented by this row. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| NUM nncVcl15MinIntervalAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.6.1.3 | NncExtAbsIntvlNumberType | read-only | The absolute interval number of this interval. |
| NUM nncVcl15MinIntervalClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.6.1.4 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVcl15MinIntervalClp0InCells | 1.3.6.1.4.1.123.3.29.1.6.1.5 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0, including those with header errors corrected. |
| NUM nncVcl15MinIntervalDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.6.1.6 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl15MinIntervalDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.6.1.7 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl15MinIntervalTaggedInCells | 1.3.6.1.4.1.123.3.29.1.6.1.8 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl15MinIntervalClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.6.1.9 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VCL with CLP=0 or 1. |
| NUM nncVcl15MinIntervalClp0OutCells | 1.3.6.1.4.1.123.3.29.1.6.1.10 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VCL with CLP=0. |
| nncVcl1HourCurrentTable | 1.3.6.1.4.1.123.3.29.1.7 | not-accessible | The nncVcl1HourCurrentTable contains objects for monitoring the performance of a VCL during the current 1 hour interval. | |
| nncVcl1HourCurrentEntry | 1.3.6.1.4.1.123.3.29.1.7.1 | not-accessible | An entry in the 1 hour current statistics table. Each conceptual row contains current statistics for a particular VCL. By default, 1 Hour statistics are not gathered. In order to enable gathering of these statistics, a row must be created. The semantics of nncVcl1HourCurrentRowStatus is the same as the definition of RowStatus in rfc1443 with the following constraints. 1. Creation is done in one step, that is, by setting the nncVcl1HourCurrentRowStatus column to createAndGo. Setting the column to createAndWait will return wrongValue. 2. The VCI specified in the instance must be an endpoint that is currently used in a VCL otherwise the agent will return return inconsistentValue and no row is created. 3. If the maximum number of rows (an agent limitation) has been reached, resourceUnavailable is returned and no row is created. 4. Creation of a current row will also enable the corresponding interval table whose rows will be created when intervals are completed. 5. Statistics collection is disabled by setting the column to destroy. This will also remove all corresponding rows in the interval table. | |
| NUM nncVcl1HourCurrentState | 1.3.6.1.4.1.123.3.29.1.7.1.1 | NncExtIntvlStateType | read-only | The state of the current interval. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| NUM nncVcl1HourCurrentAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.7.1.2 | NncExtAbsIntvlNumberType | read-only | The absolute interval number of this interval. |
| NUM nncVcl1HourCurrentClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.7.1.3 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVcl1HourCurrentClp0InCells | 1.3.6.1.4.1.123.3.29.1.7.1.4 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0, including those with header errors corrected. |
| NUM nncVcl1HourCurrentDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.7.1.5 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl1HourCurrentDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.7.1.6 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl1HourCurrentTaggedInCells | 1.3.6.1.4.1.123.3.29.1.7.1.7 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl1HourCurrentClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.7.1.8 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VCL with CLP=0 or 1. |
| NUM nncVcl1HourCurrentClp0OutCells | 1.3.6.1.4.1.123.3.29.1.7.1.9 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VCL with CLP=0. |
| ROW nncVcl1HourCurrentRowStatus | 1.3.6.1.4.1.123.3.29.1.7.1.10 | RowStatus | read-write | This object is used to create and delete rows in this table. The following sets are invalid: createAndWait, active, and notInService. Such sets will return wrongValue. |
| nncVcl1HourIntervalTable | 1.3.6.1.4.1.123.3.29.1.8 | not-accessible | The nncVcl1HourIntervalTable contains objects for monitoring the performance of a virtual Channel link over a historical stratum of M 1 hour intervals. | |
| nncVcl1HourIntervalEntry | 1.3.6.1.4.1.123.3.29.1.8.1 | not-accessible | An entry in the 1 hour interval statistics table. Each conceptual row contains statistics for a particular VCL and interval. These rows are automatically created if there is a corresponding entry in the 1 hour current table. | |
| NUM nncVcl1HourIntervalNumber | 1.3.6.1.4.1.123.3.29.1.8.1.1 | NncExtRelIntvlNumberType | not-accessible | The interval number (N) of the statistics in this row. |
| NUM nncVcl1HourIntervalState | 1.3.6.1.4.1.123.3.29.1.8.1.2 | NncExtIntvlStateType | read-only | The state of the interval represented by this row. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| NUM nncVcl1HourIntervalAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.8.1.3 | NncExtAbsIntvlNumberType | read-only | The absolute interval number of this interval. |
| NUM nncVcl1HourIntervalClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.8.1.4 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVcl1HourIntervalClp0InCells | 1.3.6.1.4.1.123.3.29.1.8.1.5 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0, including those with header errors corrected. |
| NUM nncVcl1HourIntervalDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.8.1.6 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl1HourIntervalDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.8.1.7 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl1HourIntervalTaggedInCells | 1.3.6.1.4.1.123.3.29.1.8.1.8 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVcl1HourIntervalClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.8.1.9 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VCL with CLP=0 or 1. |
| NUM nncVcl1HourIntervalClp0OutCells | 1.3.6.1.4.1.123.3.29.1.8.1.10 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VCL with CLP=0. |
| NUM nncDepthOf15MinHistoricalStrata | 1.3.6.1.4.1.123.3.29.1.9 | NncExtRelIntvlNumberType | read-only | The depth of the historical strata of 15min interval tables in this module. |
| nncVplStatTable | 1.3.6.1.4.1.123.3.29.1.10 | not-accessible | The nncVplStatTable contains objects for monitoring the accumulated performance of a VPL since measurement started on the VPL. | |
| nncVplStatEntry | 1.3.6.1.4.1.123.3.29.1.10.1 | not-accessible | An entry in the Vpl Stat table. Each conceptual row contains accumulated statistics for a particular VPL. | |
| NUM nncVplStatClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.10.1.1 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVplStatClp0InCells | 1.3.6.1.4.1.123.3.29.1.10.1.2 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VPL with CLP=0, including those with header errors corrected. |
| NUM nncVplStatDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.10.1.3 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVplStatDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.10.1.4 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVplStatTaggedInCells | 1.3.6.1.4.1.123.3.29.1.10.1.5 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVplStatClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.10.1.6 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0 or 1. |
| NUM nncVplStatClp0OutCells | 1.3.6.1.4.1.123.3.29.1.10.1.7 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0. |
| nncVclStatTable | 1.3.6.1.4.1.123.3.29.1.11 | not-accessible | The nncVclStatTable contains objects for monitoring the accumulated performance of a VCL since measurement started on the VCL. | |
| nncVclStatEntry | 1.3.6.1.4.1.123.3.29.1.11.1 | not-accessible | An entry in the Stat table. Each conceptual row contains accumulated statistics for a particular VCL. | |
| NUM nncVclStatClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.11.1.1 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0 or 1, including those with header errors corrected. This counter is formed after the UPC function. |
| NUM nncVclStatClp0InCells | 1.3.6.1.4.1.123.3.29.1.11.1.2 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress on the VCL with CLP=0, including those with header errors corrected. |
| NUM nncVclStatDiscardClp0And1InCells | 1.3.6.1.4.1.123.3.29.1.11.1.3 | NncExtCounter64 | read-only | Number of valid cells with CLP=1 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVclStatDiscardClp0InCells | 1.3.6.1.4.1.123.3.29.1.11.1.4 | NncExtCounter64 | read-only | Number of valid cells with CLP=0 discarded at ingress by ingress traffic policing, including those with header errors corrected. |
| NUM nncVclStatTaggedInCells | 1.3.6.1.4.1.123.3.29.1.11.1.5 | NncExtCounter64 | read-only | Number of valid cells admitted at ingress with CLP=0, with CLP set to 1 by ingress traffic policing, including those with header errors corrected. |
| NUM nncVclStatClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.11.1.6 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0 or 1. |
| NUM nncVclStatClp0OutCells | 1.3.6.1.4.1.123.3.29.1.11.1.7 | NncExtCounter64 | read-only | Number of valid cells transmitted at egress on the VPL with CLP=0. |
| nncAtmVplStatCounterTable | 1.3.6.1.4.1.123.3.29.1.12 | not-accessible | This table supplies the maximum interval numbers for valid data for Atm Vpl End Points in the nncVpl15MinIntervalTable and nncVpl1HourIntervaltable. | |
| nncAtmVplStatCounterEntry | 1.3.6.1.4.1.123.3.29.1.12.1 | not-accessible | An Entry in nncAtmVplStatCounterTable. | |
| INT nncAtmVplStatCounterIndex | 1.3.6.1.4.1.123.3.29.1.12.1.1 | INTEGER | read-only | This index specifies the type of interval available. 1 = hourly 2 = daily (not used) 3 = monthly (not used) 4 = 15 minute interval stats. |
| INT nncAtmVplStatCounterValue | 1.3.6.1.4.1.123.3.29.1.12.1.2 | INTEGER | read-only | This values represents the maximum interval number for valid data for Atm Vpl End Points. This number is based on the type of interval being reported. |
| nncAtmVclStatCounterTable | 1.3.6.1.4.1.123.3.29.1.13 | not-accessible | This table supplies the maximum interval numbers for valid data for Atm Vcl End Points in the nncVcl15MinIntervalTable and nncVcl1HourIntervaltable. | |
| nncAtmVclStatCounterEntry | 1.3.6.1.4.1.123.3.29.1.13.1 | not-accessible | An Entry in nncAtmVclStatCounterTable. | |
| INT nncAtmVclStatCounterIndex | 1.3.6.1.4.1.123.3.29.1.13.1.1 | INTEGER | read-only | This index specifies the type of interval available. 1 = hourly 2 = daily (not used) 3 = monthly (not used) 4 = 15 minute interval stats. |
| INT nncAtmVclStatCounterValue | 1.3.6.1.4.1.123.3.29.1.13.1.2 | INTEGER | read-only | This values represents the maximum interval number for valid data for Atm Vcl End Points. This number is based on the type of interval being reported. |
| NUM nncDepthOf1HourHistoricalStrata | 1.3.6.1.4.1.123.3.29.1.14 | NncExtRelIntvlNumberType | read-only | The depth of the historical strata of 1 hour interval tables in this module. |
| nncVpa15MinCurrentTable | 1.3.6.1.4.1.123.3.29.1.15 | not-accessible | The nncVpa15MinCurrentTable contains objects for monitoring the performance of a VPA during the current 15 minute interval. | |
| nncVpa15MinCurrentEntry | 1.3.6.1.4.1.123.3.29.1.15.1 | not-accessible | An entry in the 15 minute current statistics table. Each conceptual row contains current statistics for a particular VPA | |
| NUM nncVpa15MinCurrentState | 1.3.6.1.4.1.123.3.29.1.15.1.1 | NncExtIntvlStateType | read-only | The state of the current interval. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| I32 nncVpa15MinCurrentAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.15.1.2 | Integer32 | read-only | The absolute interval number of this interval. |
| C64 nncVpa15MinCurrentClp0And1OutCellsEx | 1.3.6.1.4.1.123.3.29.1.15.1.3 | Counter64 | read-only | Total CLP0 and CLP1 cells transmitted on all constituent VCs of a particular VPA |
| C64 nncVpa15MinCurrentDiscardClp0And1Cells | 1.3.6.1.4.1.123.3.29.1.15.1.4 | Counter64 | read-only | Total CLP0 and CLP1 cells discarded due to congestion on all constituent VCs of a particular VPA |
| C64 nncVpa15MinCurrentDiscardClp0Cells | 1.3.6.1.4.1.123.3.29.1.15.1.6 | Counter64 | read-only | Total CLP0 cells discarded due to congestion on all constituent VCs of a particular VPA |
| nncVpa15MinIntervalTable | 1.3.6.1.4.1.123.3.29.1.16 | not-accessible | The nncVpa15MinIntervalTable contains objects for monitoring the performance of a VPA during the 15 minute interval. | |
| nncVpa15MinIntervalEntry | 1.3.6.1.4.1.123.3.29.1.16.1 | not-accessible | An entry in the 15 minute current statistics table. Each conceptual row contains current statistics for a particular VPA | |
| I32 nncVpa15MinIntervalNumber | 1.3.6.1.4.1.123.3.29.1.16.1.1 | Integer32 | not-accessible | The interval number (N) of the statistics in this row. |
| NUM nncVpa15MinIntervalState | 1.3.6.1.4.1.123.3.29.1.16.1.2 | NncExtIntvlStateType | read-only | The state of the current interval. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| I32 nncVpa15MinIntervalAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.16.1.3 | Integer32 | read-only | The absolute interval number of this interval. |
| C64 nncVpa15MinIntervalClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.16.1.4 | Counter64 | read-only | Total CLP0 and CLP1 cells transmitted on all constituent VCs of a particular VPA |
| C64 nncVpa15MinIntervalDiscardClp0And1Cells | 1.3.6.1.4.1.123.3.29.1.16.1.5 | Counter64 | read-only | Total CLP0 and CLP1 cells discarded due to congestion on all constituent VCs of a particular VPA |
| C64 nncVpa15MinIntervalDiscardClp0Cells | 1.3.6.1.4.1.123.3.29.1.16.1.6 | Counter64 | read-only | Total CLP0 cells discarded due to congestion on all constituent VCs of a particular VPA |
| nncVpa1HourCurrentTable | 1.3.6.1.4.1.123.3.29.1.17 | not-accessible | The nncVpa1HourCurrentTable contains objects for monitoring the performance of a VPA during the current 1 hour interval. | |
| nncVpa1HourCurrentEntry | 1.3.6.1.4.1.123.3.29.1.17.1 | not-accessible | An entry in the 1 hour current statistics table. Each conceptual row contains current statistics for a particular VPA | |
| NUM nncVpa1HourCurrentState | 1.3.6.1.4.1.123.3.29.1.17.1.1 | NncExtIntvlStateType | read-only | The state of the current interval. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| I32 nncVpa1HourCurrentAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.17.1.2 | Integer32 | read-only | The absolute interval number of this interval. |
| C64 nncVpa1HourCurrentClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.17.1.3 | Counter64 | read-only | Total CLP0 and CLP1 cells transmitted on all constituent VCs of a particular VPA |
| C64 nncVpa1HourCurrentDiscardClp0And1Cells | 1.3.6.1.4.1.123.3.29.1.17.1.4 | Counter64 | read-only | Total CLP0 and CLP1 cells discarded due to congestion on all constituent VCs of a particular VPA |
| C64 nncVpa1HourCurrentDiscardClp0Cells | 1.3.6.1.4.1.123.3.29.1.17.1.5 | Counter64 | read-only | Total CLP0 cells discarded due to congestion on all constituent VCs of a particular VPA |
| nncVpa1HourIntervalTable | 1.3.6.1.4.1.123.3.29.1.18 | not-accessible | The nncVpa1HourIntervalTable contains objects for monitoring the performance of a VPA during the 1 hour interval. | |
| nncVpa1HourIntervalEntry | 1.3.6.1.4.1.123.3.29.1.18.1 | not-accessible | An entry in the 1hour current statistics table. Each conceptual row contains current statistics for a particular VPA | |
| I32 nncVpa1HourIntervalNumber | 1.3.6.1.4.1.123.3.29.1.18.1.1 | Integer32 | not-accessible | The interval number (N) of the statistics in this row. |
| NUM nncVpa1HourIntervalState | 1.3.6.1.4.1.123.3.29.1.18.1.2 | NncExtIntvlStateType | read-only | The state of the current interval. The object provides a status for those entries which have been reset by the user, or have been subject to a wall clock time change. |
| I32 nncVpa1HourIntervalAbsoluteIntervalNumber | 1.3.6.1.4.1.123.3.29.1.18.1.3 | Integer32 | read-only | The absolute interval number of this interval. |
| C64 nncVpa1HourIntervalClp0And1OutCells | 1.3.6.1.4.1.123.3.29.1.18.1.4 | Counter64 | read-only | Total CLP0 and CLP1 cells transmitted on all constituent VCs of a particular VPA |
| C64 nncVpa1HourIntervalDiscardClp0And1Cells | 1.3.6.1.4.1.123.3.29.1.18.1.5 | Counter64 | read-only | Total CLP0 and CLP1 cells discarded due to congestion on all constituent VCs of a particular VPA |
| C64 nncVpa1HourIntervalDiscardClp0Cells | 1.3.6.1.4.1.123.3.29.1.18.1.6 | Counter64 | read-only | Total CLP0 cells discarded due to congestion on all constituent VCs of a particular VPA |
| nncAtmStatisticsTraps | 1.3.6.1.4.1.123.3.29.2 | |||
| nncAtmStatisticsGroups | 1.3.6.1.4.1.123.3.29.3 | |||
| nncVpl15MinCurrentGroup | 1.3.6.1.4.1.123.3.29.3.1 | A collection of objects providing 15 Min current statistics for a VPI endpoint | ||
| nncVpl15MinIntervalGroup | 1.3.6.1.4.1.123.3.29.3.2 | A collection of objects providing 15 Min interval statistics for a VPI endpoint | ||
| nncVpl1HourCurrentGroup | 1.3.6.1.4.1.123.3.29.3.3 | A collection of objects providing 1 Hour current statistics for a VPI endpoint | ||
| nncVpl1HourIntervalGroup | 1.3.6.1.4.1.123.3.29.3.4 | A collection of objects providing 1 Hour interval statistics for a VPI endpoint | ||
| nncVcl15MinCurrentGroup | 1.3.6.1.4.1.123.3.29.3.5 | A collection of objects providing 15 Min current statistics for a VCI endpoint | ||
| nncVcl15MinIntervalGroup | 1.3.6.1.4.1.123.3.29.3.6 | A collection of objects providing 15 Min interval statistics for a VCI endpoint | ||
| nncVcl1HourCurrentGroup | 1.3.6.1.4.1.123.3.29.3.7 | A collection of objects providing 1 Hour current statistics for a VCI endpoint | ||
| nncVcl1HourIntervalGroup | 1.3.6.1.4.1.123.3.29.3.8 | A collection of objects providing 1 Hour interval statistics for a VCI endpoint | ||
| nncVplStatGroup | 1.3.6.1.4.1.123.3.29.3.9 | A collection of objects providing cumulative statistics for a VPI endpoint | ||
| nncVclStatGroup | 1.3.6.1.4.1.123.3.29.3.10 | A collection of objects providing cumulative statistics for a VCI endpoint | ||
| nncVplIntervalStateGroup | 1.3.6.1.4.1.123.3.29.3.11 | A collection of objects providing the state of intervals in the VPL current and interval tables. | ||
| nncVclIntervalStateGroup | 1.3.6.1.4.1.123.3.29.3.12 | A collection of objects providing the state of intervals in the VCL current and interval tables. | ||
| nncVplStatCounterGroup | 1.3.6.1.4.1.123.3.29.3.13 | A collection of objects providing the count of valid intervals in the VPL interval tables. | ||
| nncVclStatCounterGroup | 1.3.6.1.4.1.123.3.29.3.14 | A collection of objects providing the count of valid intervals in the VCL interval tables. | ||
| nncDepthOfHistoricalStrataGroup | 1.3.6.1.4.1.123.3.29.3.15 | A collection of objects providing the number of intervals supported in the interval tables. | ||
| nncVpa15MinCurrentGroup | 1.3.6.1.4.1.123.3.29.3.16 | A collection of objects providing 15 Min current statistics for a VP Aggregation | ||
| nncVpa15MinIntervalGroup | 1.3.6.1.4.1.123.3.29.3.17 | A collection of objects providing 15 Min interval statistics for a VP Aggregation | ||
| nncVpa1HourCurrentGroup | 1.3.6.1.4.1.123.3.29.3.18 | A collection of objects providing 1 hour current statistics for a VP Aggregation | ||
| nncVpa1HourIntervalGroup | 1.3.6.1.4.1.123.3.29.3.19 | A collection of objects providing 1 hour interval statistics for a VP Aggregation | ||
| nncAtmStatisticsCompliances | 1.3.6.1.4.1.123.3.29.4 | |||
| nncAtmStatisticsCompliance | 1.3.6.1.4.1.123.3.29.4.1 | The compliance statement for Newbridge SNMP entities which have Vpl/Vcl endpoints and VPA | ||
| nncAtmStatisticsServiceCompliance | 1.3.6.1.4.1.123.3.29.4.2 | The compliance statement for Newbridge SNMP Service-level entities which report on Vpl/Vcl endpoints |
RFC description
Nortel (Northern Telecom) vendor-private MIB for ATM (Asynchronous Transfer Mode) statistics collection and monitoring.
Start monitoring Newbridge Networks/Alcatel ATM switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.