LaserJet-Series4050-MIB :: hrstorageallocationfailures

MIB Reference — IPNetwork Monitor · Updated September 14, 2026

All MIBs › LaserJet-Series4050-MIB › hrstorageallocationfailures

hrstorageallocationfailures

Module: LaserJet-Series4050-MIB

OID (symbolic): LaserJet-Series4050-MIB::hrstorageallocationfailures

OID (numeric): 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.7

Node type: OBJECT-TYPE

Type: INTEGER

Access: read-only

Description: The number of requests for storage represented by this entry that could not be honored due to not enough storage. It should be noted that as this object has a SYNTAX of Counter, that it does not have a defined initial value. However, it is recommended that this object be initialized to zero. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer): This object is set to zero at power on and when any reset is done via prtGeneralReset. This object is incremented whenever the printer is short on memory (codewise: when PersMemoryCycle is called with a parameter of 2). Additional information (mass storage): Total number of writes that failed since power on) due to the mass storage device being full. Returns the value 0 when the file system has not been initialized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.

Examples

Walk all instances (SNMPv2c):

snmpwalk -v2c -c public <target> 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.7
snmpwalk -v2c -c public <target> LaserJet-Series4050-MIB::hrstorageallocationfailures

Get a specific instance (index 1):

snmpget -v2c -c public <target> 1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.7.1
snmpget -v2c -c public <target> LaserJet-Series4050-MIB::hrstorageallocationfailures.1

Start monitoring HP LaserJet 4050 series printer with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the LaserJet-Series4050-MIB::hrstorageallocationfailures OID value, configure state conditions and alerts, and monitor any HP LaserJet 4050 series printer from a single console.

How to Use in IPNetwork Monitor

Select an HP LaserJet 4050 series printer as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hrstorageallocationfailures into the Find box to locate it in the OID tree, then select it and click OK. The number of requests for storage represented by this entry that could not be honored due to not enough storage. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OID Breakdown

Upper-level ancestors (16 from the standard OID tree / other modules)
Numeric OIDNameModule
1isoLANART-AGENT
1.3orgAirPair-MIB
1.3.6dodAirPair-MIB
1.3.6.1internetAirPair-MIB
1.3.6.1.4privateAirPair-MIB
1.3.6.1.4.1enterprisesAirPair-MIB
1.3.6.1.4.1.11hpCLJ8500-MIB
1.3.6.1.4.1.11.2nmCLJ8500-MIB
1.3.6.1.4.1.11.2.3hpsystemCLJ8500-MIB
1.3.6.1.4.1.11.2.3.9net_peripheralCLJ8500-MIB
1.3.6.1.4.1.11.2.3.9.4netdmCLJ8500-MIB
1.3.6.1.4.1.11.2.3.9.4.2dmCLJ8500-MIB
1.3.6.1.4.1.11.2.3.9.4.2.3hrmCLJ8500-MIB
1.3.6.1.4.1.11.2.3.9.4.2.3.2hrStorageCLJ8500-MIB
1.3.6.1.4.1.11.2.3.9.4.2.3.2.3hrStorageTableCLJ8500-MIB
1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1hrStorageEntryCLJ8500-MIB
Numeric OIDNameModule
1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.7hrstorageallocationfailuresLaserJet-Series4050-MIB

Also defined in

Module

This MIB depends on