LaserJet-Series4050-MIB

All MIBs › LaserJet-Series4050-MIB

Description: LaserJet-Series4050-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is LaserJet-Series4050-MIB?

LaserJet-Series4050-MIB is a Hewlett-Packard proprietary module specific to the HP LaserJet 4050 series printers, providing detailed printer control-panel, status, and localization objects. It exposes device configuration data such as sleep-mode and online/offline state, control panel button presses, background status messages, and localization/country language support, alongside model and serial number identification. Its monitoring focus is squarely on hardware/device status: administrators can track power state (sleep-mode, on-off-line), error conditions via error-log-clear and background status message lines, and physical identification via model-number and serial-number. Being an HP printer-specific MIB, it is used alongside the standard Printer MIB (RFC 1759) for fuller print-device management. It is typically deployed in office environments managing fleets of HP LaserJet 4050 printers via SNMP-based print management software, and administrators can download the LaserJet-Series4050-MIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in LaserJet-Series4050-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP LaserJet 4050 series printer

Monitoring Examples

An administrator would poll on-off-line and sleep-mode to confirm whether a LaserJet 4050 unit is online and active or has entered a power-saving state, and check background-status-msg-line1-part1/line2-part1 for the printer's current status message text. A control-panel-button-press event combined with a background status message indicating a fault (e.g., paper jam or low toner) would reveal a hardware condition requiring physical attention.

What Can Be Monitored

printer online/offline state
sleep mode status
control panel status messages
control panel button presses
model and serial number
supported languages/countries

Imported Objects

From RFC1155-SMI

enterprises

From SNMPv2-TC

TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using hrstorageallocationfailures OID:

Select an HP LaserJet 4050 series printer as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hrstorageallocationfailures into the Find box to locate it in the OID tree, then select it and click OK. The number of requests for storage represented by this entry that could not be honored due to not enough storage. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT _pysmi_continue	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.6	INTEGER	write-only	A device can support a class of errors called continuable errors. When a continuable error is encountered, the device requires a continue event to occur before the device will continue operation. One continue event is setting the CONTINUE object to eInitiateAction. Devices can support other continue events, like auto-continue. A continue event causes the continuable error to be acknowledged, thus allowing the device to continue. Each device needs to list the continuable errors. If the device doesn't currently have an unacknowledged continuable error, the response will contain . Additional information: See the CLEARABLE-WARNING and AUTO-CONTINUE objects for the errors that this object will clear.
accounting	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16
active_print_jobs	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2
STR asset_number	1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.12	DisplayString	read-write	User defined asset number. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the . Additional information: The maximum supported string length is 8 characters. If the user entered string is too long, the device will store the first 8 characters and will return the status.
INT auto_continue	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.7	INTEGER	read-write	Indicates if the device will automatically continue after encountering a continuable error. If AUTO- CONTINUE is set to eOn, the device will automatically generate continue event to acknowledge continuable errors. If AUTO-CONTINUE is set to eOff, then some other continue event will have to acknowledge the continuable error. Additional information: If this is set to eOn the device displays an error message and goes offline for ten seconds. After ten seconds the printer automatically returns to the online state. If this is set to eOff then the device displays an error message and goes offline. It remains offline until the operator presses the GO key or until the CONTINUE object is set. If the printer is not idle, the new value may not take effect until a job boundary is reached. If a get is done on this object before the job boundary is reached, the value last set will be returned.
background_message	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37
background_message1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.1
background_message2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.2
STR background_status_msg_line1_part1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.1.1	DisplayString	read-write	The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '00 READY'. Additional information: The display size for the LaserJet 4050 Series printers is 2 X 16. The value of this object and the current value of BACKGROUND-STATUS-MSG-LINE2-PART1 are displayed together on the 2-line display, but they must be set independently. If line 2 has been set, and the next message to be displayed only requires line 1, BACKGROUND-STATUS-MSG-LINE2-PART1 must be set to the null string to clear it. This object allows a message to be displayed when it is the highest priority message. Setting this object does not guarantee the message will be displayed; and reading it returns the value last written, not the currently displayed message (use prtConsoleDisplayBufferText to read the display). The priority assigned for displaying this message is one lower than the READY message. In other words, the only message that can be replaced by these objects is the READY message. To clear the message, write a null string to both this object and BACKGROUND-STATUS-MSG-LINE2-PART1.
STR background_status_msg_line2_part1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.37.2.1	DisplayString	read-write	The string displayed on the device's front panel in place of the printer's built-in background status string. An example built-in background status string is '00 READY'. Additional information: See BACKGROUND-STATUS-MSG-LINE1-PART1
INT cancel_job	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.2	INTEGER	write-only	Cancels the print job whose ID matches the value written to the CANCEL-JOB object. The host first learns the job ID using the CURRENT-JOB-PARSING-ID command. If the printer has completely processed the job, the printer responds with . If the value of the CURRENT-JOB-PARSING-ID is smaller than the value written to the CANCEL-JOB object, then the printer responds with . When read, returns the value of the last job ID what was canceled, or -1 to indicate no job has been canceled. Additional information: If the value written matches the ID of a job that is currently being canceled (for any reason), the printer responds with . LaserJet 4050 Series uses job ID's in the range of 0..32767. Because the ID number can wrap to zero, CURRENT-JOB-PARSING-ID may be smaller than the value written to this object; when this occurs, no error will result as long as the ID is for a currently processing job. This object is write only, so the comment in the general description stating the job ID or -1 will be returned on a read does not apply.
INT channel_bytes_received	1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.3	INTEGER	read-only	The low order 31 bits of the number of bytes received by the printer from the host on this logical channel.
INT channel_bytes_sent	1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.2	INTEGER	read-only	The low order 31 bits of the number of bytes sent from the printer to the host on this logical channel.
channel_entry	1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1
INT channel_io_errors	1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.4	INTEGER	read-only	The low order 31 bits of the number of I/O errors which have occured on this logical channel.
INT channel_jobs_received	1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.5	INTEGER	read-only	The low order 31 bits of the number of print jobs which have been received on this logical channel.
INT channel_mio	1.3.6.1.4.1.11.2.3.9.4.2.1.7.2.1.6	INTEGER	read-only	The number of the MIO card associated with this logical channel. If this logical channel is not associated with an MIO card a zero is returned. The value returned for each logical channel is the MIO card's physical slot number. The list of supported values should be documented in the device POS. Additional information: The value returned will be zero for channels 1..3. If an MIOA card is installed, channels 4..10 will return a value of one or two. If an MIOB card is installed, channels 11..17 will return a value of one or two but not the same as channels 4..10. When two IIO cards are installed, the value returned by any channel 4..17 may change after the printer is power cycled.
channel_table	1.3.6.1.4.1.11.2.3.9.4.2.1.7.2
INT clearable_warning	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.1	INTEGER	read-write	Returns or controls how the device will track clearable warnings. A clearable warning indicates a transient event in the device. The device will continue after the transient event occurs. If CLEARABLE-WARNING is eOff, the device does not track clearable warnings. If CLEARABLE-WARNING is eOn, all clearable warnings will be tracked until cleared (acknowledged). If CLEARABLE- WARNING is eJob, a clearable warning generated due to an event that occurs because of the print job being processed will be automatically cleared when the device has finished processing the job. Example clearable warning events include the device altering resolution or page protection due to memory constraints. The POS will document what transient events are treated as clearable warnings. Additional information: If set to eOn, the warning is displayed until the GO key is pressed or the CONTINUE object is set. If set to eJob, the warning is displayed until the end of the job in which it was generated.
INT cold_reset_media_size	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.19	INTEGER	read-write	Returns or sets the media size that is used as the DEFAULT-MEDIA-SIZE when a cold reset occurs.
OCT collated_originals_support	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.42	OCTET STRING	read-only	Indicates that the printer can create multiple, collated 'originals' of a job and shows the level of support for this capability. cCollatedOriginals - The printer can create multiple collated originals, or 'mopies'. This is the base functionality required by the other collection items. cProofAndHold - The printer saves a copy of the job while printing the first mopy. Later, this held job can be released and the rest of the mopies will print. cSecurityPrint - The printer spools the job and holds the job until the user releases the job by entering a password at the printer's control panel. cAutoHighlight - The printer prints the job a number of times with a mail distribution list prepended to each job. A different mailing address is highlighted on each mopy. cCollatedAtSpeed - The printer can create multiple collated copies where all copies after the original are printed at engine speed. Additional information: Indicates that the printer can create multiple, collated originals of a job and shows the level of support for this capability. cCollatedOriginals - The printer can create multiple collated originals, or mopies. This is the base functionality required by the other collection items. None of them are supported by Jonah. Without disk, this object will not exist. This will be set at boot-up initialization. If the disk fails, in any way, then the disk error functionality will handle the situation. The value of this object will be: !cCollatedOriginals - Only FLASH installed cCollatedOriginals - IDE is installed combined with/without FLASH cCollatedOriginals - RAMDISK is On combined with/without FLASH
INT control_panel_button_press	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.60	INTEGER	write-only	Writing this object simulates pressing a button on the control panel.
INT current_job_parsing_id	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1.1	INTEGER	read-only	Contains the printer assigned job identification for the job currently being processed by the processing PDL sub- system. The job ID is a monotonically increasing number. The job ID may be reset to zero at power-up and may roll over to zero after reaching some maximum value. Additional information: A value of -1 is returned when the printer is not parsing a job. When data for a new job is detected, this object is updated (the job may or may not turn out to be a Null Job); however, the trap does not occur until the printer determines that it is not a Null Job. (A job is considered to be a 'null job' if it has no name or job attribute, causes no pages to be printed, and consumes MIN_JOB_SIZE (9) or fewer bytes.) A trapped value will differ from the previous value by one or more. Some job-info- objects are created when the first data bytes are received. If the printer determines that the job is a Null Job, the job-info- objects related to the Null Job are deleted. LaserJet 4050 Series retains the job-info- objects for the MAX_JOBS_IN_LIST (12) most recent jobs that are not Null Jobs. The first job received after power-up will have job ID 1, and the job ID will increment to 32767 before rolling to zero. To distinguish whether a power cycle or a rollover causes a reduction in the job ID value, the object prtGeneralConfigChanges can be watched and if it increments at the same time as the drop is observed in the value of CURRENT-JOB-PARSING-ID, then a power cycle is the most likely cause.
INT custom_paper_dim_unit	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.7	INTEGER	read-write	The units of measure used to specify the width and height of the printer's custom paper. The unit of measure of eTenThousandthsOfInches is 0.0001 inches. Additional information: The only valid values for this object are eTenThousandthsOfInches (3), and eMicrometers (4). The data for this object is stored in NVRAM.
INT custom_paper_feed_dim	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.8	INTEGER	read-write	Sets the printer's custom paper dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product. Additional information: The valid range for LaserJet 4000 Series is 50000 to 140000 if CUSTOM-PAPER-DIM-UNIT is eTenThousandthsOfInches or 127000 to 355600 if CUSTOM-PAPER-DIM-UNIT is ePmicrometers. Attempts to set this object outside the valid range will result in a return value of .
INT custom_paper_xfeed_dim	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.9	INTEGER	read-write	Sets the printer's custom paper dimension in the cross- feed direction (direction ninety degrees relative to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product. Additional information: The valid range for LaserJet 4000 Series is 30000 to 85000 if CUSTOM-PAPER-DIM-UNIT is eTenThousandthsOfInches or 76200 to 215900 if CUSTOM-PAPER-DIM-UNIT is ePmicrometers. Attempts to set this object outside the valid range will result in a return value of .
INT default_bits_per_pixel	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.39	INTEGER	read-write	Controls the number of levels used (per pixel) when printing grayscale or color images.
INT default_copies	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.4	INTEGER	read-write	Returns or changes default copies. Default copies is the default values used by the PDL to control the number of copies of each page in the print job that are printed. The print job can override this value. The list of supported values should be documented in the device POS. Additional information: The supported values are 1 through 999. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snaps are as follows: 999 snaps to 999
INT default_horizontal_black_resolution	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.9	INTEGER	read-write	Returns or changes the value of the default horizontal black resolution. The units are dots per inch. Additional information: In LaserJet 4050 Series changing this object also causes DEFAULT-VERTICAL-BLACK RESOLUTION to change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are 300 and 600 for LaserJet 8100 Series and LaserJet 8000 Series, and 300, 600, and 1200 for LaserJet 5000 Series and LaserJet 4000 Series. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follow: LaserJet 5000 Series and LaserJet 4000 Series: n = n = 900 snaps to 1200 LaserJet 8100 Series and LaserJet 8000 Series: n = 450 snaps to 600
INT default_lines_per_page	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.11	INTEGER	read-write	Returns or changes the default number of lines per page. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return the . Additional information: The supported values in LaserJet 4050 Series are 5 to 128. Setting to an unsupported value causes the the printer to substitute in a snap value and to return status. The snap values are as follow: 128 snaps to 128
STR default_media_name	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.22	DisplayString	read-write	Returns or sets the media name that is used until the media name is changed by a print job command. Additional information: This string must be one of the MEDIAn-NAME objects. The value of this object is saved across a power cycle.
INT default_media_size	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.13	INTEGER	read-write	This indicates the default media size. A write of an unsupported value causes an . Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document.
INT default_page_protect	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.10	INTEGER	read-write	Returns or changes the default page protection behavior. If eOff, the device does not reserve memory for holding the entire raster form of a processed page. If eOn, then memory is reserved. If eAuto, the device determines the amount of memory to reserve. Additional information: Setting to eOn causes MET to be more conservative, but it will not allocate memory to hold an entire rasterized page.
INT default_print_quality	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6.7	INTEGER	read-write	Returns or sets the default print quality. A value of zero has the lowest print quality. A value of 100 has the highest print quality. Each POS should document what values in the 0 to 100 range are supported. Additional information: In LaserJet 4050 Series, the supported values are 0 and 100. A value of zero has the lowest print quality(ECONOMODE=ON), thus minimizes the amount of toner used to print a page. A value of 100 has the highest print quality (ECONOMODE=OFF), thus uses more toner to print a page. Setting to an unsupported value outside of the 0 to 100 range causes the printer to return status. Setting to an unsupported value inside of the 0 to 100 range causes the printer to substitute in a snap value (listed below) and to return status. The snap values are as follow: 0 to 50 snap to 0 51 to 100 snap to 100
INT default_ret	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6.5	INTEGER	read-write	Returns or changes the Resolution Enhancement Technology setting. Devices that only support eOff and on should map all other values to on and always return the same non-eOff value to indicate on. The list of supported values should be documented in the device POS. Additional information: Setting this object may cause a status of to be returned, but the new value will not take effect until a job boundary is reached. If a get is done on object before the job boundary is reached, the value last set will be returned. The value of this object is saved over a powercycle.
INT default_vertical_black_resolution	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.8	INTEGER	read-write	Returns or changes the value of the default vertical black resolution. The units are dots per inch. Additional information: In LaserJet 4050 Series changing this OID also causes DEFAULT- HORIZONTAL-BLACK RESOLUTION to change. DEFAULT- HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are 300 and 600 for LaserJet 8100 Series and LaserJet 8000 Series, and 300, 600, and 1200 for LaserJet 5000 Series and LaserJet 4000 Series. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follow: LaserJet 5000 Series and LaserJet 4000 Series: n = n = 900 snaps to 1200 LaserJet 8100 Series and LaserJet 8000 Series: n = 450 snaps to 600
INT default_vmi	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.12	INTEGER	read-write	Returns or changes the default vertical motion index. The unit of measure for VMI is centipoints per line. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return .
destination_subsystem	1.3.6.1.4.1.11.2.3.9.4.2.1.4
device	1.3.6.1.4.1.11.2.3.9.4.2.1
STR device_location	1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.11	DisplayString	read-write	User defined device location. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the . Additional information: The maximum supported string length is 16 characters. If the user entered string is too long, the device will store the first 16 characters and will return the status.
STR device_name	1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.10	DisplayString	read-write	User defined device name. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the . Additional information: The maximum supported string length is 32 characters. If the user entered string is too long, the device will store the first 32 characters and will return the status.
dm	1.3.6.1.4.1.11.2.3.9.4.2
INT duplex_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.22	INTEGER	read-only	Total number of sheets of media that have been duplex printed. A sheet is counted if it travels through the duplex page path, regardless of whether or not marks are made on the page. The POS will indicate if the value is kept in NVRAM. Additional information: In LaserJet 4050 Series the count is kept in NVRAM however the NVRAM value is only updated every 10 sheets. NOTE: The value returned by this object will be incremented every sheet but if power is lost between NVRAM updates up to 9 sheets of the count may be lost. The counter will be reset to zero after 16,777,215 (2^24-1) pages.
INT energy_star	1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1	INTEGER	read-write	Returns or changes the Energy Star sleep value. If the value is greater than zero, then the device will go into energy saving sleep mode after the print engine has been idle for the number of seconds specified by this object. A value of zero means Energy Star is disabled and the device will not go to sleep based on print engine idle time. The value must be non-negative. Additional information: Returns or changes the Energy Star sleep value. The device will go into energy saving sleep mode after the print engine has been idle for the number of seconds specified by this object. LaserJet 4050 Series supports values of 0, 900, 1800, 3600, 7200, and 10800. A value of 0 means never go to sleep based on print engine idle time. Setting to an unsupported value causes the printer to substitute a value (listed below) and to return status. The values are as follow: =1 and =1350 and =2700 and =5400 and =9000 snap to 10800 (3 hours)
STR engine_media_modes_supported1	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4.1	DisplayString	read-only	The list of engine media modes supported by the device. The modes are each separated by a comma character. An example string would be: 'Normal,Rough,Low,Vellum'.
INT error_log_clear	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.38	INTEGER	write-only	Setting this object clears all the entries in the error log sub-tree. Additional information: Setting this object removes all errors that have been stored in the printer's non-volatile memory.
error1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1
INT error1_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: Returns a device specific error code. If the error code returned is '0', then the printer has not yet logged an error for this object. When the maximum number of errors is reached (30 on LaserJet 4050 Series printers), and a new error occurs, the error in ERROR1-CODE will be replaced by the one in ERROR2-CODE, and so on until the last error object will be given the value of the new error. The error number is returned in the upper 16 bits. If it is 68, 69, 79, or 80, then the sub code is returned in the lower 16 bits (eg. 68 001C, where the subcode is already a hexadecimal value). If the error number is any other number, then the 1st sub code (XX) will be in bits 15-8 and the 2nd sub code (YY) will be in bits 7-0 (eg. 55.04.02) where XX=04 and YY=02). Example: If the error is 68 001A, then the value returned will be 4456474. To break it down: 4456474 = 0x0044001A The upper 16 bits: 0x0044 = 68 The lower 16 bits: 0x001A = 001A Which is the error: 68 001A Example: If the error is 55.04.241, then the error code will be 3605745. To break it down: 3605745 = 0x003704F1 The upper 16 bits: 0x0037 = 55 The upper byte of the lower 16 bits: 0x04 = 04 The lower byte of the lower 16 bits: 0xF1 = 241 Which is the error: 55.04.241
INT error1_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.1.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 1 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: This item contains the engine page count when the error occurred. If there is currently no error entry for this object, a '0' will be returned. Note that '0' may also be returned when there is a valid error, but a current page count was unavailable. If ERROR1-CODE object also returns '0', then an error has not yet been logged for this object. See ERROR1-CODE for an explanation of the order used for storing errors.
error10	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10
INT error10_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error10_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.10.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 10 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error11	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11
INT error11_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error11_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.11.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 11 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error12	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12
INT error12_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error12_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.12.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 12 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error13	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13
INT error13_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error13_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.13.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 13 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error14	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14
INT error14_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error14_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.14.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 14 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error15	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15
INT error15_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error15_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.15.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 15 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error16	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16
INT error16_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error16_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.16.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 16 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error17	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17
INT error17_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error17_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.17.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 17 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error18	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18
INT error18_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error18_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.18.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 18 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error19	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19
INT error19_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error19_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.19.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 19 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2
INT error2_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error2_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.2.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 2 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error20	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20
INT error20_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error20_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.20.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 20 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error21	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21
INT error21_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error21_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.21.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 21 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error22	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22
INT error22_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error22_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.22.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 22 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error23	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23
INT error23_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error23_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.23.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 23 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error24	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24
INT error24_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error24_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.24.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 24 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error25	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25
INT error25_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error25_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.25.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 25 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error26	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26
INT error26_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error26_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.26.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 26 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error27	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27
INT error27_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error27_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.27.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 27 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error28	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28
INT error28_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error28_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.28.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 28 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error29	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29
INT error29_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error29_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.29.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 29 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error3	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3
INT error3_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error3_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.3.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 3 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error30	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30
INT error30_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error30_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.30.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 30 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error4	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4
INT error4_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error4_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.4.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 4 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error5	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5
INT error5_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error5_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.5.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 5 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error6	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6
INT error6_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error6_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.6.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 6 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error7	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7
INT error7_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error7_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.7.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 7 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error8	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8
INT error8_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error8_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.8.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 8 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
error9	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9
INT error9_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.2	INTEGER	read-only	Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.
INT error9_time_stamp	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11.9.1	INTEGER	read-only	Contains some sort of time stamp indicating when error 9 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.
errorlog	1.3.6.1.4.1.11.2.3.9.4.2.1.1.11
file_system	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10
INT file_system_max_open_files	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.2	INTEGER	read-write	The number of open files allowed at one time. Opening a file when the maximum number of files are currently open will fail. Additional information: Indicates the number of open files a personality (e.g. PCL or PostScript) is guaranteed to be able to open before the file system runs out of file handles. After writing this object, the printer must be rebooted (powercycled) before the change takes effect. This object supports any value between 32 - 512 inclusive. If a value Less then 32 then it snaps to 32 if greater then 512 it snaps to 512. The factory default value is dependent on the amount of installed RAM. The default value of 32 is when Memory 4MB. Performing a cold reset sets this object back to the factory default value. Returns status if attempting to access this object and there is no storage device is installed. Default for LaserJet 4000 Series/LaserJet 5000 Series is 32 Default for LaserJet 8000 Series/LaserJet 8100 Series/LaserJet 4050 Series is 128
INT file_system_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.1	INTEGER	read-only	The amount of memory, in bytes, used by the file system to buffer file data. Additional information: Reports the amount of memory, in bytes, reserved for use by the file system. Returns status if attempting to access this object and there is no storage device is installed. The values remain constant across reboots. Possible Values: FILE-SYSTEM-MAX-OPEN-FILES 32 512 EIO DISK 69916 198556 EIO DISK + 1 2MB Flash 88940 217580 1 2MB Flash 33052 161692
INT file_system_statistic_current_memory_usage	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.5	INTEGER	read-only	A value indicating the number of bytes of RAM currently used by the file system firmware. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed. This will veri depending on the number and size of Mass Storage devices installed.
INT file_system_statistic_max_memory_usage	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.6	INTEGER	read-only	A value indicating the maximum number of bytes of RAM used by the file system firmware. The POS should state if the value is reset to zero after a power cycle. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT file_system_statistic_read_open	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.1	INTEGER	read-only	The number of times the file system has received requests to open a file for reading. Opening a file for both reading and writing will cause this value to change. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed. This value is increamented when a file is opened.
INT file_system_statistic_successful	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.3	INTEGER	read-only	A counter indicating the number of file system requests that completed successfully. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT file_system_statistic_unsuccessful	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.4	INTEGER	read-only	A counter indicating the number of file system requests that completed unsuccessfully. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT file_system_statistic_write_open	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2.2	INTEGER	read-only	The number of times the file system has received requests to open a file for writing. Opening a file for both reading and writing will cause this value to change. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed. This value is increamented when a file is opened.
OCT file_system_test_return_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1.3	OCTET STRING	write-only	This test object that will not be supported in any released product. Setting this object allows the next file system call return code to be specified or to simulate uninitialized or unistalled volumes. The POS will specify the binary format. Additional information: A three byte binary value. The first byte indicates what function is being effected by this set. value \| function ------+------------------ 1 \| PersFSCtl 2 \| PersFSDirClose 3 \| PersFSDirCreate 4 \| PersFSDirDelete 5 \| PersFSDirOpen 6 \| PersFSDirRead 7 \| PersFSDirReadStd 8 \| PersFSDirRewind 9 \| PersFSDirSeek 10 \| PersFSDirTell 11 \| PersFSFileClose 12 \| PersFSFileDelete 13 \| PersFSFileMove 14 \| PersFSFileOpen 15 \| PersFSFileRead 16 \| PersFSFileSeek 17 \| PersFSFileStatus 18 \| PersFSFileWrite 19 \| PersFSFlush 20 \| PersFSVolChk 21 \| PersFSVolFix 22 \| PersFSVolInit 23 \| PersFSVolStatus The return value of the function being effected will return the value -1 to indicate an error occurred. The second byte is the value returned by the next call to PersFSErrNo() (after the call being effected is called). Refer to the 'Copernicus Personality Interface Volume 2 Disk File System' documentation for a list of values returned by PersFSErrNo(). The third byte indicates which call to the specified file system routine will fail. A value of one means the first call will fail. A value of two means the second call will fail, and so on. Writing this object causes any previous write to this object to be invalidated. Note: The error triggering mechanism is actually implemented at the message interface to the file system rather than at the PersFSxxx() function call interface. This is easier to do, and it is better for NFS because NFS uses the message interface rather than the PersFSxxx() functions. Fortunately there is a one-to-one mapping between messages and PersFSxxx() functions so everything works out nicely. The printer will uninitialize the mass storage device if the first byte is one of the values listed below. value \| meaning ------+------------------ 101 \| Effects the printer state 102 \| Effects the data on the device The Moby printer supports 3 volumes zero, so the second byte must be 0 - 2. The third byte has no meaning and must be zero.
file_system2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.2
INT file_system2_initialize_volume	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.2.6	INTEGER	write-only	Setting this object to eInitializing causes file system 2 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 mass storage device, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM2-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 1st device.
file_system3	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.3
INT file_system3_initialize_volume	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.3.6	INTEGER	write-only	Setting this object to eInitializing causes file system 3 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 mass storage device, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM3-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 2nd device.
file_system4	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.4
INT file_system4_initialize_volume	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3.4.6	INTEGER	write-only	Setting this object to eInitializing causes file system 4 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 mass storage devices, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM4-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 3rd device.
file_systems	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.3
INT form_feed	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.5	INTEGER	write-only	Instructs the PDL processing sub-system to finishing processing the current page of the current job. Form feed is also known as close page or eject page. If the PDL processing sub-system is in a FORM-FEED-NEEDED state, this causes the device to flush or finish processing the current page of the current job. If the device is not in the FORM-FEED-NEEDED state, an will occur.
INT form_feed_needed	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.2.2	INTEGER	read-only	Indicates if the PDL processing sub-system has made marks on the current page and the source subsystem has been idle for a device specific amount of time. Additional information: LaserJet 4050 Series will set this object to eTrue when it has made marks on the current page, the IO-TIMEOUT has expired while PCL was running in `backward-compatibility mode' (which is caused by jobs consisting purely of PCL data with no prepended PJL commands), and no data is pending on another I/O. Once it is set to eTrue, more data on the same I/O will cause this object to be set to eFalse, until the above conditions are met again.
STR fw_rom_datecode	1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.5	DisplayString	read-only	Identifies the base system firmware date code. The date code will be encoded in the yyyymmdd format. There may be several versions of the base system firmware. The date code associated with the version of the base system firmware that is being used is reported. There may be other date code objects for other specific modules such as fonts, localization modules, etc.; these other datecode objects are device specific.
held_job	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7
held_job_control	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2
INT held_job_delete	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.2	INTEGER	write-only	Instructs the printer to delete the specified held job from the list. The job-id is used to identify which job to delete. A held job can also be deleted from the control panel. Additional information:
INT held_job_enable	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.4	INTEGER	read-write	Enables or disables Job Retention (Job Hold). The valid values are eDisabled and eEnabled. (Specifying an invalid mode causes an error to be returned.) When eDisabled is specified all Job Retention (Hold, Proof, Store, PIN Printing) is disabled. When eEnabled is specified, the Job Retention characteristics of a given job are defined by the PJL variable SET HOLD. Additional information: When disabled, currently held jobs are not removed, but must be explicitly removed through the Control Panel or the PML object HELD-JOB-DELETE.
held_job_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1
STR held_job_job_name	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.2	DisplayString	read-only	The job name may be generated by the driver or obtained from user input.
STR held_job_pin	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.6	DisplayString	read-only	A string that is specified in the job stream and then required to be entered in order to release the job for printing. PIN stands for Personal Identification Number. Additional information: Must be a 4 digit string, each digit must be 0..9 or a null string if there is no pin.
OCT held_job_print	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.1	OCTET STRING	write-only	Instructs the printer to schedule the specified held job for printing with the specified number of copies. The job-id is used to identify which job to print. A held job can also be printed from the control panel. Additional information: Bytes 0-3 is the job id of the job to print. Bytes 4-7 is the number of copies to print.
INT held_job_quantity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.5	INTEGER	read-only	Number of copies to print.
INT held_job_retention	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.3	INTEGER	read-only	Indicates the retention classification of the job. The values indicate whether the job is printed immediately and/or stored. There are 4 options: OFF: The job is printed but not retained on the disk. ON: The job is printed and stored temporarily on the disk. PROOF: One copy of the job is printed and the remaining copies are stored on the disk. STORE: The job is not printed but stored on the disk.
INT held_job_security	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.4	INTEGER	read-only	The variable specifies the security level of the job. PUBLIC: The job does not require a PIN in order to release the job for printing. PRIVATE: The job requires a PIN in order to be released for printing.
INT held_job_set_queue_size	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.2.3	INTEGER	read-write	Sets the maximum number of jobs which can be stored in the held job list. Additional information: Sets the size of the temporary job lists queue.
STR held_job_user_name	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.7.1.1	DisplayString	read-only	User name that is obtained by the driver through some internal method or from user input. Additional information: The following is a general description for all the JOB-MANAGEMENT objects described below. These object describe the attributes of the dynamic list containing all the stored jobs on the disk available for printing or deleting via the job-management feature. The jobs on this list are not deleted from the disk unless explicitly specified by the user. A print job may be specified for retention by PJL commands in the data stream. Following is a list of the PJL commands (i.e. these comments describe the PJL implementation and in some cases do not reflect the PML implementation.): @PJL SET HOLD=OFF\|ON\|PROOF\|STORE\|PRINT GENERAL DESCRIPTION: This variable specifies the retention classification of the job. The values indicate whether the job is printed immediately and/or stored. OFF: The job is printed but not retained on disk after printing. This is the default value. ON: This setting may be thought of as free proof-and-hold. The requested number of copies will be printed and the job will be temporarily stored on disk. The job will then be available for printing additional copies through the control panel and through PML. There will be a limit to the number of these temporary jobs that may be stored, and when the limit is exceeded the oldest job will be removed from the disk. PROOF: One copy of the job is printed and remaining copies are stored on disk. The job is then available to select for printing via the control panel menus or PML. The job will be deleted from the disk when the disk space is needed for another proof and hold job but only after the additional copies have been printed. It will also be deleted when the user sends down another proof and hold job with the same job name, or the user explicitly deletes the job. STORE: The job is not printed immediately but is retained on disk. The job is available to select for printing via the control panel DEFAULT VALUE: OFF The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET USERNAME= GENERAL DESCRIPTION: Eighty-character user name that is obtained by the driver through some internal method or from user input. If the job stream does not contain a USERNAME the default value will be NO USER NAME. The driver is responsible for determining the size of the printers control panel and sending a string of appropriate length. DEFAULT VALUE: NO USER NAME The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and, INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET JOBNAME= GENERAL DESCRIPTION: Eighty-character job name that may be generated by the driver or obtained from user input. This value may be used in conjunction with the USERNAME to select a job from the front panel. If the job stream does not contain a JOBNAME, the printer will assume no job name; each subsequent job that is sent down by the same user would replace the users last job on disk. The driver is responsible for determining the size of the printers control panel and sending a string of appropriate length. NOTE: The limit of 80 bytes is a PJL limit. The limit for PML will be 40 bytes. DEFAULT VALUE: NULL STRING The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET HOLDTYPE=PUBLIC\|PRIVATE GENERAL DESCRIPTION: This variable specifies the privacy level of the job. PUBLIC: The job does not require a PIN in order to be released for printing. This is the default value. PRIVATE: The job requires a PIN in order to be released for printing. The PIN is specified by the HOLDKEY variable. If the HOLDTYPE is set to PRIVATE, a HOLDKEY value must be specified. If no HOLDKEY is specified, the job will be considered PUBLIC. DEFAULT VALUE: PUBLIC The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET HOLDKEY=4 digits, 0000...9999 GENERAL DESCRIPTION: A 4-digit string, each digit 0-9, that is specified in the job stream and then required to be entered in order to release the job for printing. If a HOLDTYPE is PRIVATE, a HOLDKEY value must be specified. If no HOLDKEY value is specified, a job will be considered PUBLIC. DEFAULT VALUE: NULL STRING The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. The format for the OID is as follows: 3.4.1.6.x.y \| \| \| \| \ / \| job-id in the system / \ PML_JOB_MGNT_ROOT_OID \ job attribute 1..6 x values are 1..6: 1) user-name: user name that is obtained by the driver through some internal method or from user input. 2) job-name: job name may be generated by the driver or obtained from user input. 3) hold: indicates the retention classification of the job. The values indicate whether the job is printed immediately and/or stored. There are 4 options: OFF: The job is printed but not retained on the disk. ON: The job is printed and stored temporarily on the disk. STORE: The job is not printed but stored on the disk. PROOF: One copy of the job is printed and the remaining copies are stored on the disk. 4) holdtype: The variable specifies the security level of the job. PUBLIC: The job does not require a PIN in order to release the job for printing. PRIVATE: The job requires a PIN in order to be released for printing. 5) quantity: number of copies to print. Valid values are 0..999. 6) pin: A 4 digit string, each digit is 0-9, that is specified in the job stream and then required to be entered in order to release the job for printing. y : an unsigned 15 bit number which uniquely identifies the job. The job id for the job remains the same for the job until it is deleted from the held jobs list. For example, the OID below is asking for the user name of the job whose id is 3. The application would issue: OID get 3.4.1.6.1.3 For example, the OID values sequence is as follows: OID returned OID getnext 3.4.1.6 3.4.1.6.1.1 getnext 3.4.1.6.1.1 3.4.1.6.1.2 getnext 3.4.1.6.2.1 3.4.1.6.2.2 ... getnext 3.4.1.6.1.6 3.4.1.6.1.7 getnext 3.4.1.6.2.1 3.4.1.6.2.2 getnext 3.4.1.6.5.2828 3.4.1.6.6.1 NOTE: for example above, job id 2828 is the last job in the list of held jobs. ... Also supported is on the job attributes: OID returned OID getnext 3.4.1.6.1 3.4.1.6.1.1 getnext 3.4.1.6.6 3.4.1.6.6.1
INT hold_job_timeout	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.10	INTEGER	read-write	The time, in minutes, that the printer will wait before automatically deleting a held job. This allows the printer to automatically clean up jobs that have been forgotten (held but never released). Additional information: This only applies to temporary held jobs, i.e., HOLD=ON or PROOF. This is a global timer that only affects the jobs that are sent after it is set. A value of 0 means never delete the jobs. Setting it to an unsupported value causes the printer to substitute a value (listed below) and to return status. LaserJet 4050 Series supports values of 0, 60, 240, 1440, and 10080 The values are as follows: =1 and =151 and =841 and =2881 snap to 10080 (1 week)
INT host_application_available_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.59	INTEGER	read-only	Returns the amount of memory, in bytes, that the device has available for job-related processing or resources. Also known as driver work space (DWS) memory.
hp	1.3.6.1.4.1.11
hpsystem	1.3.6.1.4.1.11.2.3
hrDevice	1.3.6.1.4.1.11.2.3.9.4.2.3.3
OCT hrdevicedescr	1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.3	OCTET STRING	read-only	A textual description of this device, including the device's manufacturer and revision, and optionally, its serial number. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : The serial number is not returned with this object. This object is not localized. Additional information (mass storage) : Returns status if attempting to perform a Get on this OID with no mass storage device installed.
hrDeviceEntry	1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1
INT hrdeviceerrors	1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.6	INTEGER	read-only	The number of errors detected on this device. It should be noted that as this object has a SYNTAX of Counter, that it does not have a defined initial value. However, it is recommended that this object be initialized to zero. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (mass storage): Total number of read and write errors that have occurred since the printer was turned on. Returns status if attempting to perform a Get on this OID with no mass storage device installed. Returns 0 if the mass storage device is uninitialized.
OID hrdeviceid	1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.4	OBJECT IDENTIFIER	read-only	The product ID for this device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : The complete OID reported by this object is: .1.3.6.1.4.1.11.2.3.9.1.2.12 Additional information (mass storage) : Constant. Since we don't know all the possible registered OIDs for each mass storage device model that could be installed in this printer, this object always returns the unknown product ID. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
INT hrdeviceindex	1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.1	INTEGER	read-only	A unique value for each device contained by the host. The value for each device must remain constant at least from one re-initialization of the agent to the next re-initialization. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer): The entry in the Device Table which describes the printer. Additional information (mass storage): Constant. The index is assigned by the person controlling the printer object definition. All device/mass storage/file system/partition tables in Host Resources MIB and the Printer MIB that relate to the mass storage device use the same index value. The value of the index of the following objects is this object's value: prtDeviceRefIndex hrDiskStorageIndex hrPartitionIndex hrFSIndex The value of the object matches the value of the object's index. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
INT hrdevicestatus	1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.5	INTEGER	read-only	The current operational state of the device described by this row of the table. A value unknown(1) indicates that the current state of the device is unknown. running(2) indicates that the device is up and running and that no unusual error conditions are known. The warning(3) state indicates that agent has been informed of an unusual error condition by the operational software (e.g., a disk device driver) but that the device is still 'operational'. An example would be high number of soft errors on a disk. A value of testing(4), indicates that the device is not available for use because it is in the testing state. The state of down(5) is used only when the agent has been informed that the device is not available for any use. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : The printer's condition is mapped as follows (printer): eHrunning -- Printer ready to print or is printing. May be in power save mode. eHwarning -- A condition exists that needs attention but it is not currently preventing printing. A non-critical alert is active. eHdown -- Printer is not printing because it is offline or a critical alert is active. Human interaction is needed to bring the printer to a ready state. Additional information (mass storage) : Returns mass storage device status information. running -- mass storage device functional. May be in power save mode. warning -- The mass storage device failed a self-test but completed the power-on initialization sequence. The mass storage device is readable even when the mass storage device fails the power-up self-test in order to give the customer a chance to retrieve any data that can be made available. testing -- Mass storage device is executing a test. down -- Mass storage device is non-functional. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
hrDeviceTable	1.3.6.1.4.1.11.2.3.9.4.2.3.3.2
OID hrdevicetype	1.3.6.1.4.1.11.2.3.9.4.2.3.3.2.1.2	OBJECT IDENTIFIER	read-only	An indication of the type of device. If this value is `hrDeviceProcessor { hrDeviceTypes 3 }' then an entry exists in the hrProcessorTable which corresponds to this device. If this value is `hrDeviceNetwork { hrDeviceTypes 4 }', then an entry exists in the hrNetworkTable which corresponds to this device. If this value is `hrDevicePrinter { hrDeviceTypes 5 }', then an entry exists in the hrPrinterTable which corresponds to this device. If this value is `hrDeviceDiskStorage { hrDeviceTypes 6 }', then an entry exists in the hrDiskStorageTable which corresponds to this device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (mass storage): Constant. Applications should determine if a mass storage device is installed by getting this object. If the response is something other than HRMhrDeviceDiskStorage, the application knows this row in the hrDeviceTable does not refer to a mass storage object. Due to restrictions placed on this object by the Host Resources Disk Table, the value of this object must be HRMhrDeviceDiskStorge. Returns status if attempting to perform a Get on this OID with no mass storage device installed. HRMhrDeviceDiskStorage is 1.3.6.1.2.1.25.3.1.6
INT hrdiskstorageaccess	1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1.1	INTEGER	read-write	An indication if this long-term storage device is readable and writable or only readable. This should reflect the media type, any write-protect mechanism, and any device configuration that affects the entire device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: This object can be set to write protect the mass storage device, even though the host resources MIB documents the object as read-only. Applications wanting to know if the mass storage device is writable should get this object. Applications wanting to change the read/write access of the mass storage device should set this object. If this object is set to write-protect while a file is being written to the mass storage device, the write-protect takes effect immediately and the new file doesn't appear in the file system. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
INT hrdiskstoragecapacity	1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1.4	INTEGER	read-only	The total size for this long-term storage device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The capacity is in Kbytes. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
hrDiskStorageEntry	1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1
INT hrdiskstoragemedia	1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1.2	INTEGER	read-only	An indication of the type of media used in this long-term storage device. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Applications can determine if the installed mass storage device is a disk or is flash by getting this value. Possible Values: EIO DISK returns eHhardDisk Ram Disk returns eHramDisk Flash Disk returns eHother Returns status if attempting to perform a Get on this OID with no mass storage device installed.
INT hrdiskstorageremoveble	1.3.6.1.4.1.11.2.3.9.4.2.3.3.6.1.3	INTEGER	read-only	Denotes whether or not the disk media may be removed from the drive. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
hrDiskStorageTable	1.3.6.1.4.1.11.2.3.9.4.2.3.3.6
INT hrfsaccess	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.5	INTEGER	read-write	An indication if this file system is logically configured by the operating system to be readable and writable or only readable. This does not represent any local access-control policy, except one that is applied to the file system as a whole. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Returns the same value as hrDiskStorageAccess. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
INT hrfsbootable	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.6	INTEGER	read-only	A flag indicating whether this file system is bootable. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
hrFSEntry	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1
INT hrfsindex	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.1	INTEGER	read-only	A unique value for each file system local to this host. The value for each file system must remain constant at least from one re-initialization of the agent to the next re-initialization. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The index is assigned by the person controlling the printer object definition. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OCT hrfslastfullbackupdate	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.8	OCTET STRING	read-only	The last date at which this complete file system was copied to another storage device for backup. This information is useful for ensuring that backups are being performed regularly. If this information is not known, then this variable shall have the value corresponding to January 1, year 0000, 00:00:00.0, which is encoded as (hex)'00 00 01 01 00 00 00 00'. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The default value is the value defined to represent an unknown time of January 1, year 0000, 00:00:00.0. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OCT hrfslastpartialbackupdate	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.9	OCTET STRING	read-only	The last date at which a portion of this file system was copied to another storage device for backup. This information is useful for ensuring that backups are being performed regularly. If this information is not known, then this variable shall have the value corresponding to January 1, year 0000, 00:00:00.0, which is encoded as (hex)'00 00 01 01 00 00 00 00'. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The default value is the value defined to represent an unknown time of January 1, year 0000, 00:00:00.0. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OCT hrfsmountpoint	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.2	OCTET STRING	read-only	The path name of the root of this file system. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
OCT hrfsremotemountpoint	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.3	OCTET STRING	read-only	A description of the name and/or address of the server that this file system is mounted from. This may also include parameters such as the mount point on the remote file system. If this is not a remote file system, this string should have a length of zero. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. This printer does not support remote file system mounting. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
INT hrfsstorageindex	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.7	INTEGER	read-only	The index of the hrStorageEntry that represents information about this file system. If there is no such information available, then this value shall be zero. The relevant storage entry will be useful in tracking the percent usage of this file system and diagnosing errors that may occur when it runs out of space. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The value indicates the hrStorageTable index for this mass storage device. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
hrFSTable	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8
OID hrfstype	1.3.6.1.4.1.11.2.3.9.4.2.3.3.8.1.4	OBJECT IDENTIFIER	read-only	The value of this object identifies the type of this file system. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed or if the file system has not been initialized.
hrm	1.3.6.1.4.1.11.2.3.9.4.2.3
INT hrmemorysize	1.3.6.1.4.1.11.2.3.9.4.2.3.2.2	INTEGER	read-only	The amount of physical main memory contained by the host. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The unit of measure for this object is 1024 bytes. The default value assumes the base printer with no additional memory.
hrPartitionEntry	1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1
INT hrpartitionfsindex	1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.5	INTEGER	read-only	The index of the file system mounted on this partition. If no file system is mounted on this partition, then this value shall be zero. Note that multiple partitions may point to one file system, denoting that that file system resides on those partitions. Multiple file systems may not reside on one partition. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Indicates if the mass storage device has been initialized. Applications determine if the storage device has been initialized by getting this object. Returns zero if the mass storage device is not initialized, otherwise the value matches the hrDeviceIndex value for this mass storage device. The value indicates the hrFileSystemTable index for the file system stored on this partition. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OCT hrpartitionid	1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.3	OCTET STRING	read-only	A descriptor which uniquely represents this partition to the responsible operating system. On some systems, this might take on a binary representation. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The value returned is the ASCII string version of the hrDeviceIndex for this mass storage device. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
INT hrpartitionindex	1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.1	INTEGER	read-only	A unique value for each partition on this long- term storage device. The value for each long-term storage device must remain constant at least from one re-initialization of the agent to the next re- initialization. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: Constant. The first and second index indicates the hrDeviceIndex for this mass storage device. The value of this object is the same as the second index. The printer only supports one partition per mass storage device. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OCT hrpartitionlabel	1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.2	OCTET STRING	read-write	A textual description of this partition. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The MS-DOS volume label. The volume label is writable. Returns status if attempting to perform a Get on this OID with no mass storage device installed. This object is settable and returns the empty string if the mass storage device has not been initialized. NOTE the RamDisk will lose this value after a PowerCycle.
INT hrpartitionsize	1.3.6.1.4.1.11.2.3.9.4.2.3.3.7.1.4	INTEGER	read-only	The size of this partition. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The capacity is in Kbytes. Returns the same value as hrDiskStorageCapacity. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
hrPartitionTable	1.3.6.1.4.1.11.2.3.9.4.2.3.3.7
OCT hrprinterdetectederrorstate	1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1.2	OCTET STRING	read-only	This object represents any error conditions detected by the printer. The error conditions are encoded as bits in an octet string, with the following definitions: Condition Bit # hrDeviceStatus lowPaper 0 warning(3) noPaper 1 down(5) lowToner 2 warning(3) noToner 3 down(5) doorOpen 4 down(5) jammed 5 down(5) offline 6 down(5) serviceRequested 7 warning(3) If multiple conditions are currently detected and the hrDeviceStatus would not otherwise be unknown(1) or testing(4), the hrDeviceStatus shall correspond to the worst state of those indicated, where down(5) is worse than warning(3) which is worse than running(2). Bits are numbered starting with the most significant bit of the first byte being bit 0, the least significant bit of the first byte being bit 7, the most significant bit of the second byte being bit 8, and so on. A one bit encodes that the condition was detected, while a zero bit encodes that the condition was not detected. This object is useful for alerting an operator to specific warning or error conditions that may occur, especially those requiring human intervention. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: LaserJet 4050 Series reports error conditions as follows: lowPaper -- A tray is empty, but the media to be loaded is not currently needed. hrDeviceStatus = eHwarning; hrPrinterStatus = eHidle or eHprinting; A non-critical alert is active. noPaper -- A tray is empty and must be filled for printing to continue. hrDeviceStatus = eHdown; hrPrinterStatus = eHother; A critical alert is active. lowToner -- Toner is almost gone. The quality of printed pages will begin to deteriorate until the toner is completely gone. hrDeviceStatus = eHwarning; hrPrinterStatus = eHidle or eHprinting; A non-critical alert is active. noToner -- LaserJet 4050 Series printers do not report this condition. coverOpen -- A printer cover or door is open. hrDeviceStatus = eHdown; hrPrinterStatus = eHother; A critical alert is active. jammed -- Paper is jammed and the printer will be unable to continue printing until the jam is cleared. hrDeviceStatus = eHdown; hrPrinterStatus = eHother; A critical alert is active. offline -- Printer is offline and will not accept new print jobs until it is online again. hrDeviceStatus = eHdown; hrPrinterStatus = eHother; A critical alert is active. serviceRequested -- Any status or error condition not listed above. If the condition prevents printing, the 'offline' bit is also set and the hrDeviceStatus and hrPrinterStatus listed for offline above are returned. hrDeviceStatus = eHwarning; hrPrinterStatus = eHidle or eHprinting; A non-critical alert is active.
hrPrinterEntry	1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1
INT hrprinterstatus	1.3.6.1.4.1.11.2.3.9.4.2.3.3.5.1.1	INTEGER	read-only	The current status of this printer device. When in the idle(1), printing(2), or warmup(3) state, the corresponding hrDeviceStatus should be running(2) or warning(3). When in the unknown state, the corresponding hrDeviceStatus should be unknown(1). Refer to RFC 1514, Host Resources MIB, for more details. Additional information: The printer's condition is mapped as follows: eHother -- The printer is offline or a critical alert is active. eHidle -- The printer is not doing any of the items listed below for eHprinting status. eHprinting -- A job is currently being processed or printed or a PJL job is being processed. eHwarmup -- If hrDeviceStatus is eHdown, then the printer is currently offline but is resolving the condition that caused it be offline. If hrDeviceStatus is eHrunning, then the printer was in power save mode and is now ready ready to print.
hrPrinterTable	1.3.6.1.4.1.11.2.3.9.4.2.3.3.5
hrStorage	1.3.6.1.4.1.11.2.3.9.4.2.3.2
INT hrstorageallocationfailuresEx	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.7	INTEGER	read-only	The number of requests for storage represented by this entry that could not be honored due to not enough storage. It should be noted that as this object has a SYNTAX of Counter, that it does not have a defined initial value. However, it is recommended that this object be initialized to zero. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer): This object is set to zero at power on and when any reset is done via prtGeneralReset. This object is incremented whenever the printer is short on memory (codewise: when PersMemoryCycle is called with a parameter of 2). Additional information (mass storage): Total number of writes that failed since power on) due to the mass storage device being full. Returns the value 0 when the file system has not been initialized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
INT hrstorageallocationunits	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.4	INTEGER	read-only	The size, in bytes, of the data objects allocated from this pool. If this entry is monitoring sectors, blocks, buffers, or packets, for example, this number will commonly be greater than one. Otherwise this number will typically be one. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : Unit is one byte. Additional information (mass storage) : Returns the value 1024 if the file system is not initialized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
OCT hrstoragedescr	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.3	OCTET STRING	read-only	A description of the type and instance of the storage described by this entry. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer) : This object is not localized. Additional information (mass storage) : This string indicates the location of the installed mass storage device. The supported values are: 'Flash disk in DIMM slot 1' 'Flash disk in DIMM slot 2' 'Flash disk in DIMM slot 3' 'Disk in EIO 1' 'Disk in EIO 2' 'Disk in EIO 3' 'Static RAM disk using system memory' Applications determine the location of the installed mass storage device by getting this object. This string is not localized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
hrStorageEntry	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1
INT hrstorageindex	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.1	INTEGER	read-only	A unique value for each logical storage area contained by the host. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (mass storage) : Constant. The index is assigned by the person controlling the printer object definition. The value of the hrFileSystemStorageIndex and the index of the prtStorageRefIndex use the value of this object's index. The value of the object matches the value of the object's index. Returns status if attempting to perform a get on this OID with no mass storage device installed. This first volume installed will be number 2, followed by the second. IDE will always be 2. If ram disk and flash disk are installed then Flash disk will be 2 followed by ram disk. The Storage types are: IDE (EIO DISK), Flash Disk, Ram Disk
INT hrstoragesize	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.5	INTEGER	read-only	The size of the storage represented by this entry, in units of hrStorageAllocationUnits. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (printer): Total formatter RAM. Additional information (mass storage): Applications can determine the size of the installed mass storage device by getting the hrStorageAllocationUnits object and this object. The size of the mass storage device is these two returned values multiplied together. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
hrStorageTable	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3
OID hrstoragetype	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.2	OBJECT IDENTIFIER	read-only	The type of storage represented by this entry. Refer to RFC 1514, Host Resources MIB, for more details. Additional information (mass storage): Constant. Returns status if attempting to perform a Get on this OID with no mass storage device installed. HRMhrStorageFixedDisk is 1.3.6.1.2.1.25.2.1.4
INT hrstorageused	1.3.6.1.4.1.11.2.3.9.4.2.3.2.3.1.6	INTEGER	read-only	The amount of the storage represented by this entry that is allocated, in units of hrStorageAllocationUnits. Refer to RFC 1514, Host Resources MIB, for more details. Additional information: This object returns the amount of memory in use by the printer at the current time. This object should not be used when creating a print job for the device because the amount of memory in use will likely be different when the printer processes the print job. Additional information (mass storage) : Applications can determine the amount of used space on the installed mass storage device by getting the hrStorageAllocationUnits object and this object. The amount of used space is these two returned values multiplied together. Returns the value 0 if the file system is not initialized. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
id	1.3.6.1.4.1.11.2.3.9.4.2.1.1.3
imaging	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.6
interface	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4
intray	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3
intray1	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1
intray2	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2
intray3	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3
intray4	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.4
intray5	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.5
intray6	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.6
intrays	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3
io	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1
INT io_buffer_size	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.6	INTEGER	read-write	Returns or configures the amount of memory, in bytes, dedicated to I/O print job data buffering. Attempting to set to an unsupported value causes the device to use the closest supported value. Each device POS should document the list of supported values. Additional information: In LaserJet 4050 Series the minimum supported value is 10K bytes (10240). The maximum supported value is dependent on total memory installed and the amount of memory currently being used by other memory consumers. Use the MAXIMUM-IO-BUFFERING-MEMORY object to determine this value. The following rules determine legal values for this object: 1) Sizes less than 10K bytes will snap to 10K bytes. 2) Sizes between 10K and 100K bytes will be rounded to the nearest 10K. 3) Sizes between 100K bytes and the maximum value allowed will round to the nearest 100K bytes. If the value had to be snapped or rounded, will be returned along with the actual value that was written. Attempting to set this object when IO-BUFFERING is eOff will cause a status of to be returned. When IO-BUFFERING is eOff, reading this object will return a value of zero.
INT io_buffering	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.5	INTEGER	read-write	Returns or controls the manner in which the device performs I/O data buffering. I/O data buffering allows additional print job data to be buffered by the I/O sub- system in an effort to allow the computer sending the data to perform other tasks and to keep the PDL processing sub-system busy. eOff, I/O buffering is disabled. When eOn, I/O buffering is enabled and the IO-BUFFER-SIZE object controls the amount of memory set aside for I/O buffer. When eAuto, I/O buffering is enabled and the I/O buffer size is determined automatically by the device and the IO-BUFFER-SIZE object is not used. Additional information: In a PCL-only printer, all values may be set at any time. When there is less than 4M of memory installed, setting this object to eOn or eAuto will cause to be returned. At exactly 4M of memory, eOn is not a valid setting. At more than 4M of memory any setting is valid, subject to the conditions listed in the interactions below.
INT io_switch	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.2	INTEGER	read-only	Indicates if the device will switch between I/O channels when a job boundary is encountered and print job data is available on another I/O channel.
INT io_timeout	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.1	INTEGER	read-write	The amount of time, in seconds, to wait for more print job data to be received before an I/O timeout occurs. The I/O channel being timed is the I/O channel that received the data associated with the current print job. If an I/O timeout occurs, the PDL processing sub-system assumes all the data associated with the current print job has been received, and processes the end of job in an PDL specific manner. The POS specifies the supported values. Additional information: If an I/O timeout occurs,the PDL processing sub-system will consider it an end of job condition only if there is data from another I/O subsystem waiting to be processed. The supported values are 5 to 300 seconds. Setting to a value outside the supported range returns status and the value will be snapped to the nearest supported value.
jetsend_contact	1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.3
OCT jetsend_contact_ip_address_security	1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.3.1.2	OCTET STRING	write-only	A C structure containing the following fields: typedef struct { ubyte reserved[3]; ubyte command; /* command: 0 to 1 */ ubyte password[8]; ubyte IPAddress[4]; } jetsend_contact_ip_address_security_t; where ubyte is an unsigned byte (0-255). The defined values defined for command are: When command is 0: IPAddress is 0: device is locked, no one can contact it IPAddress is > 0: only that address is allowed to contact the device When command is 1: IPAddress is 0: any device can contact it IPAddress is > 0: any device matching this mask can contact it. If the result of logically anding the mask value supplied in the IPAddress field with the sending device's IP address matches the result of logically anding the mask value supplied in the IPAddress field with this device's IP address, then JetSend will allow the session to be established. Additional information: Controls the device or class of device(s) which may communicate with the JetSend processing subsystem. The following C data structure contains the relevant fields (described in subsequent paragraphs): typedef struct { unsigned char reserved[3]; unsigned char command; unsigned char password[8]; unsigned char IPAddress[4]; } The 'reserved' field is not used and should remain zero-filled. The 'command' field interpretation differs based on its value: 0 = Accept session(s) only from the specific device whose IP address matches the specified IP address; all other session request(s) from non-matching device(s) are rejected. 1 = Accept session(s) only from the specific device(s) whose IP address(es) conform to the mask specified in the 'IPAddress' field; all other session request(s) from device(s) with non-matching submask(s) are rejected. (If the result of logically AND'ing the mask value supplied in the 'IPAddress' field with the sending device's IP address matches the result of logically AND'ing the mask value supplied in the 'IPAddress' field with this device's IP address, then JetSend will allow session establishment. Password absence/presence determines whether the device will allow the caller to alter the IP address security. If the password is disabled, the caller may set the 'command' and 'IPAddress' fields directly. If the password is enabled, the caller may (re-)set the 'command' and 'IPAddress' fields only after specifying the matching 'password' field. (Refer to the aforementioned 'JETSEND-CONTACT-PASSWORD' object ID.) (Specifying either an invalid 'command' field value or a 'password' field greater than eight (8) bytes or an 'IPAddress' field greater than four (4) bytes causes the error to be returned.) This object will be enabled in IR devices even if is does not detect an EIO card.
OCT jetsend_contact_password	1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.3.1.1	OCTET STRING	write-only	A C structure containing the following fields: typedef struct { ubyte old_password[8]; ubyte new_password[8];/ } jetsend_change_contact_password_t; where ubyte is an unsigned byte (0-255). Additional information: Controls access to the JetSend processing subsystem. Password absence/presence determines whether the device will allow a session to be established. The following C data structure contains the relevant fields (described in subsequent paragraphs): typedef struct { unsigned char old_password[8]; unsigned char new_password[8]; } Whenever the password is disabled (i.e., is zero-filled for its entire length), the device is indicating its willingness to allow session establishment. Whenever the password is enabled (i.e., has one or more non-zero-filled values), the device is controlling session establishment -- all in-progress JetSend sessions must supply a matching password or the device will reject the in-progress session. To disable the password, specify the matching password via the 'old_password' field and zero-fill the 'new_password' field. To enable the password for the first time, zero-fill the 'old_password' field and specify the new password via the 'new_password' field (the new password should not be zero-filled; otherwise, the password will remain disabled). To enable or change the password thereafter, specify the matching password via the 'old_password' field and specify the new password via the 'new_password' field (the new desired password should not be zero-filled; otherwise, the password will be disabled). To determine if the password is enabled, zero-fill both the 'old_password' and 'new_password' fields. If an error occurs, the password is enabled; otherwise, the password is disabled. (Specifying either an 'old_password' or 'new_password' fields greater than eight (8) bytes causes the error to be returned.) This object will be enabled in IR devices even if is does not detect an EIO card.
INT jetsend_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.1.1	INTEGER	read-write	Enables or disables the JetSend processing sub-system. Additional information: Enables or disables the JetSend processing subsystem. The valid values are eOff and eOn. (Specifying an invalid mode causes an error to be returned.). This object will be enabled in IR devices even if is does not detect an EIO card.
jetsend_proc_sub	1.3.6.1.4.1.11.2.3.9.4.2.1.3.8
job	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6
job_being_parsed	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.2.1
job_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5
OCT job_info_attr_1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.1	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. Attribute objects are saved sequentially, starting with 1, after the start of a job. If more attributes are set than there are objects to store them, the excess JOBATTR values are ignored. If the corresponding SET JOBATTR= command has not been received when a get is done for this object, a status of will be returned.
OCT job_info_attr_10	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.10	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_11	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.11	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_12	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.12	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_13	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.13	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_14	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.14	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_15	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.15	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_16	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.16	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.2	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_3	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.3	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_4	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.4	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_5	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.5	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_6	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.6	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_7	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.7	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_8	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.8	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
OCT job_info_attr_9	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23.9	OCTET STRING	read-only	Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.
job_info_attribute	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.23
OCT job_info_change_id	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1.3	OCTET STRING	read-only	Returns the current value of an object in the job-info sub-tree whose value has changed. Define the object identifier for the object whose value has changed as job-info.required-field.optional-field.job-id. job-info represents the OID prefix of all objects in the job-info sub-tree. Required-field represents the OID field value that follows the job-info prefix. Since some objects in the job-info sub-tree have two OID fields between the job-info prefix and the job-id, the optional-field represents the OID field between the required-field and the job-id field, if present. Using this definition, the format for the JOB-INFO-CHANGE-ID binary value can be described as follows: Bytes 0-3 : required-field Bytes 4-7 : optional-field, or all zeros if there is no optional field Bytes 8-11: Job ID. Bytes 12-n : The value of the object job-info. required-field.optional-field.job-id. All multi-byte values stored in Motorola (big-endian) format, where the most significant byte occurs first. Additional information: LaserJet 4050 Series will use this object to report changes to the job-info-pages-printed and job-info-state objects. The required-field (bytes 0 through 3) will designate whether the change to be reported involves the pages printed (13) or job state (15). The optional-field (bytes 4 through 7) will always be zeroes. The value-field (bytes 12 through 15) will contain the new value for pages printed or job state cast to a 32-bit integer.
INT job_info_io_source	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.11	INTEGER	read-only	Indicates which I/O source, the print job was received over. The value maps to port numbering scheme supported in the DEVICE/SOURCE-SUBSYSTEM/IO/PORTS sub-tree.
STR job_info_name1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.1	DisplayString	read-only	Contains the first part of this print job's name. The last OID field for this dynamic object contains the job ID. Additional information: The job name is the string specified by the NAME= parameter of the @PJL JOB command which allows a maximum of 80 characters. The first 40 characters are in this object and the second 40 are in job-info-name2. The symbol set is Roman-8. When jobs are nested, the value assigned to this object is the name provided by the most recent @PJL JOB NAME= command. If no name is provided, a null string is returned.
STR job_info_name2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.2	DisplayString	read-only	Contains the second part of this print job's name. The last OID field for this dynamic object contains the job ID. Additional information: See job-info-name1.
OCT job_info_outbins_used	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.20	OCTET STRING	read-only	Indicates which output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional information: The bins designated by this collection include the printer's own output bins as well as the `logical output bins' associated with any attached external paper handling devices. (The mapping of the physical output bins of an external paper handling device to its `logical output bins' depends on the usage mode of the device. For instance, in `mailbox mode', there is one-to-one correspondence of `logical output bins' to physical bins, whereas in `stacker mode', one `logical output bin' may map to several physical bins.) Although LaserJet 5000 Series and LaserJet 4000 Series both come with two output bins -- a face-down bin on the top of the device and a face-up bin at the back of the device -- firmware will not provide a means of selecting between the two, nor will it report which of the two gets used. For this reason, bit 0 (cOutbin1) of this collection is being used to designate both of these bins together.
INT job_info_outcome	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.19	INTEGER	read-only	Indicates if any warning or error conditions were encountered while processing the assoicated job. The last OID field for this dynamic object contains the job ID. Additional information: In LaserJet 4050 Series, warnings and errors are not recorded in this object. Although no meaningful information can be obtained from this object, it is kept around for the compatibility needs of existing software.
INT job_info_page_count_current_original	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.25	INTEGER	read-only	The page number being printed within the current copy of a collated multi-copy job. This value changes when the job-info-pages-printed changes. The job-info-pages- printed indicates the total number of pages printed in the job, while this object indicates the number of pages printed for this copy of a collated multi-copy job. Additional information: The number of pages in the current copy of a collated multi-copy job which have been completely printed and safely delivered to the output bin.
INT job_info_pages_in_original	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.26	INTEGER	read-only	Number of pages in a single copy of a collated multi- copy job.
INT job_info_pages_printed	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.13	INTEGER	read-only	Indicates the number of pages printed by the destination subsystem. If non of the cSourceSubsystem, cProcessingSubsystem or cDestinationSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the total number of pages printed for this job. This value may increase by two each time for duplex jobs. The last OID field for this dynamic object contains the job ID. Additional information: If multiple copies of a page are printed, each copy is counted individually.
INT job_info_pages_processed	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.12	INTEGER	read-only	Indicates the number of pages processed by the processing subsystem. If neither the cSourceSubsystem or the cProcessingSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the total number of pages processed for this job. The last OID field for this dynamic object contains the job ID. Additional information: This object is incremented by one when a page is processed (`closed' by the personality), regardless of the number of pages that are printed as a result of the single page processed. In other words, it does not matter how many identical copies of a page are printed or no pages may be printed if operating in silent run mode, this count is incremented exactly once. A page is considered processed when all of the input data has been processed for a page (that is, when the intermediate has been produced, and the personality has `closed' the page. At this time, the image of the page is not necessarily completely formed.)
OCT job_info_physical_outbins_used	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.22	OCTET STRING	read-only	Indicates which physical output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional information: The output bins designated by the bits of this collection include the standard output bin(s) plus the physical bins of attached external paper handling devices. The configuration (if any) of external paper handling devices will determine the mapping of individual bits in this collection to the physical bins of the devices. For LaserJet 4050 Series (LaserJet 4050), the cOutbin1 is used for Face Down bin, cOutbin2 is used for Face Up bin, and 3-15 are used for the 13 optional output bins (12 plus an extension to the Face Up bin) for backwards compatibility with LaserJet 8000 Series/LaserJet 8100 Series and forwards compatibility with future printers. However, since LaserJet 4050 Series cannot distinguish output going to the Face Up or Face Down bin in the firmware because the diverter can only be moved manually, bit 0 (cOutbin1) is being used to designate both of these bits together. If an external paper handling output device is connected, then bit 2 (cOutbin3) will represent the device's first output bin (and so on).
INT job_info_printed_originals	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.27	INTEGER	read-only	Number of collated copies completely printed and delivered to the output bin at time of query.
INT job_info_requested_originals	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.24	INTEGER	read-only	The number of requested collated copies. The value was supplied with the job via PJL QTY variable, the PostScript Collate and NumCopies entries in the page device dictionary, or via some other mechansim.
INT job_info_size	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.14	INTEGER	read-only	Indicates the number of bytes of data processed by the processing subsystem. If neither of the cSourceSubsystem or cProcessingSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the size of this job, in bytes. The last OID field for this dynamic object contains the job ID. Additional information: This count may be incremented by values other than one as blocks of data are processed; blocks of data (which may be as large as 2K bytes) will be processed in a varying amount of time. During the processing of a job and even when a job completes, an exact count of the number of I/O bytes processed by the job is not necessarily to be expected.
OCT job_info_stage	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.10	OCTET STRING	read-only	Indicates what printer sub-systems are currently processing this print job. The last OID field for this dynamic object contains the job ID. cSourceSubsystem - some of the job is in the printer I/O subsystem. cProcessingSubsystem - some of the job is in the printer imaging processing subsystem. cDestinationSubsystem - some of the job is being printed. Additional information: For LaserJet 4050 Series, cSourceSubsystem and cProcessingSubsystem will always be set and cleared together. They are set when the beginning of the job is detected, and they are cleared when the end of the job is parsed. A non-printing job will never set cDestinationSubsystem. When a page is ready to be printed (the intermediate has been built and the page is `closed' by the personality), cDestinationSubsystem will be set even if a page of a previous job is currently being printed. cDestinationSubsystem remains set until the last page of the job has finished printing. If a page requires extensive processing and allows all the previous pages of a job to complete printing, cDestinationSubsystem will remain set until the last page of the job has finished printing.
INT job_info_state	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.5.15	INTEGER	read-only	Indicates the state of the job. The last OID field for this dynamic object contains the job ID. eAborted - the print job was aborted. eWaitingForResources - the print job requires resources that are not currently available. Example resources that can cause the job to wait include the print engine or PDL processor being unavailable. The print engine could be unavailable due to paper out, paper jam, staple out, stapler jam, marking agent low, output bin full, etc. The PDL processor could be unavailable due to an off-line condition. Each printer specific object specification should state which conditions cause a job to be waiting for resources and also state which objects can be retrieved by an application to determine the exact cause of a resource being unavailable. ePrinted - the job has printed. The related JOB-INFO- OUTCOME object indicates if any problems were encountered while the job was processed. eRetained - the job can be reprinted. eTerminating - the job was aborted or cancelled and is currently is terminating. eInterrupted - the job has been interrupted. The job can be continued. ePaused - the job has been paused. The job can be continuted. eCancelled - the job has been cancelled. eProcessing - the job is currently being printed normally.
OCT job_input_auto_continue_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.36	OCTET STRING	read-write	Returns or sets the device behavior when the desired media is not currently available. cCancelJob - The device cancels the job. The device POS should explain what happens if this item is not the only item in the collection. cAutoMediaSizeOverride - The device is allowed to substitute a different size media. cAutoMediaNameOverride - The device is allowed to substitute a different media name. Additional information: If cCancelJob is set, the current print job will be canceled regardless of other item settings. At least one bit of the collection must be set; setting this object to zero will cause a status of to be returned. This object applies to all media requests, including Manual Feed Requests. This object describes the action that is performed when the JOB-INPUT-AUTO-CONTINUE-TIMEOUT expires. The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions. The data for this object is stored in NVRAM.
INT job_input_auto_continue_timeout	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.35	INTEGER	read-write	The number of seconds the device waits after a job related continuable error occurs before automatically continuing. An example job related continuable error is the job requesting a media size that is not available. After the timeout expires, the device will continue processing the job as if a continue event occurred, such as the front panel continue key being pressed. If the value is -1, the device does not automatically continue after a job related continuable error occurs. If the value is 0, the device immediately continues. If the value is greater than 0, the value represents the timeout value in seconds. Additional information: This object is used only for media requests (size and/or name). LaserJet 4050 Series supports any value in the range of -1 to 3600. Setting to a value outside of that range causes the printer to substitute a value (listed below) and to return status. The values are as follow: 3600 snaps to 3600 (60 minutes) The action that occurs when this timeout expires is explained by JOB-INPUT-AUTO-CONTINUE-MODE. It is not the same as the CONTINUE object being set to eInitiateAction or the Select key being pressed on the control panel. See the CONTINUE object description for information on the actions that occur for those conditions. The data for this object is stored in NVRAM.
INT job_output_auto_continue_timeout	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.40	INTEGER	read-write	Returns or sets the time that the printer will wait after an output bin becomes full and the printer is trying to deliver a sheet of media to that output bin. When the timeout expires, the job is processed according to the OUTBINn-OVERRIDE-MODE. A value of -1 indicates that the printer will wait for a continue event. A non- negative value is the number of seconds to wait. Additional information: A value of zero means to continue immediately. The value of this object is stored in NVRAM, so it is maintained across a power cycle. The data for this object is stored in NVRAM.
STR localization_countries_supported	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.53	DisplayString	read-only	The list of countries supported by the device. The countries are primarily, but not limited to, two character codes from ISO 3166, each separated by a comma character. Additional information: This string will always be in the Roman-8 character set. See prtLocalizationCountry for details about each country value.
STR localization_languages_supported	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.52	DisplayString	read-only	The list of languages supported by the device. The languages are primarily, but not limited to, two character codes from ISO 639, each separated by a comma character. Additional information: This string will always be in the Roman-8 character set. See prtLocalizationLanguage for details about each language value.
INT low_marking_agent_processing	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1.3	INTEGER	read-write	Returns or changes how the device processes a low marking agent event. If eCont, then the device continues to print. If eStop, then the device stops until a continue event occurs.
marking_agent	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5
mass_storage_block_driver	1.3.6.1.4.1.11.2.3.9.4.2.1.1.15
INT mass_storage_resource_change_counter	1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3.1	INTEGER	read-only	A counter which changes when a mass storage based resource has been added or deleted. Additional information: The value of this counter changes each time the MASS-STORAGE-RESOURCE-CHANGED object is set to eTrue. The value also changes when the mass storage device is initialized. However, the value does not change when a mass storage device is removed and a different mass storage device is installed. Initializing all volumes sets this object back to the factory default value. A reboot sets this object back to the factory devalut value. Returns status if attempting to access this object and there is no storage device is installed.
INT mass_storage_resource_changed	1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3.2	INTEGER	write-only	Setting to eTrue causes MASS-STORAGE-RESOURCE-CHANGE- COUNTER to be incremented. Additional information: Returns status if attempting to access this object and there is no storage device is installed.
mass_storage_resources	1.3.6.1.4.1.11.2.3.9.4.2.1.1.12.3
INT maximum_io_buffering_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1.7	INTEGER	read-only	This object's name is misleading. Returns the maximum amount of additional memory, in bytes, that can be dedicated to buffering print job data.
INT maximum_ram_disk_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.2.1	INTEGER	read-only	This object's name is misleading. This object does not return the maximum configurable RAM disk size. Instead, it returns the maximum amount of memory, in bytes, that can used to increase the size of the RAM disk. Additional information: This object returns the maximum amount of additional memory that is available for increasing the size of the RAM disk.
INT maximum_resource_saving_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.7	INTEGER	read-only	This object's name is misleading. This object returns the maximum amount of additional memory, in bytes, that can be dedicated to holding PDL permanent soft resources. Additional information: NOTE: The values listed below have not been verified on LaserJet 4050 Series. The following numbers assume that IO-BUFFERING=eOff; if IO-BUFFERING<>eOff, the following numbers will be reduced by the value of IO-BUFFER-SIZE. Memory for resource saving is allocated in increments of 102400 bytes. Therefore, for each 1M (1048576 bytes) of memory added to the printer, 102400 bytes are made available to resource saving (and I/O buffering) and 24576 bytes are retained until an additional 102400 byte block can be made available. The value reported by this object is always rounded down to the nearest multiple of 102400. For a PCL-only printer, the value of this object is zero (all resource saving memory is dedicated to PCL). If PostScript is installed without a duplex unit, the value of this object is as follows: Zero if <7M memory is installed. 1048576 if 7M memory is installed and RESOURCE-SAVING=eOff. 1048576 if 7M memory is installed and RESOURCE-SAVING=eOn (note that this value will be reduced by the amount of memory allocated to PCL-RESOURCE-SAVING-MEMORY-SIZE and POSTSCRIPT-RESOURCE-SAVING-MEMORY-SIZE). 819200 if 7M memory is installed and RESOURCE-SAVING=eAuto. When RESOURCE-SAVING=eAuto, 819200 bytes of each 1M over 7M memory installed are allocated to PCL and PostScript (409600 each) with the remaining bytes added to this object. When RESOURCE-SAVING=eOn or eOff, all bytes over 13M memory installed are added to this object. If PostScript is installed with a duplex unit, the value of this object is as follows: Zero if <13M memory is installed. 1048576 if 13M memory is installed and RESOURCE-SAVING=eOff. 1048576 if 13M memory is installed and RESOURCE-SAVING=eOn (note that this value will be reduced by the amount of memory allocated to PCL-RESOURCE-SAVING-MEMORY-SIZE and POSTSCRIPT-RESOURCE-SAVING-MEMORY-SIZE). 1048576 if 13M memory is installed and RESOURCE-SAVING=eAuto. When RESOURCE-SAVING=eAuto, 810200 bytes of each 1M over 13M memory installed are allocated to PCL and PostScript (409600 each) with the remaining bytes added to this object. When RESOURCE-SAVING=eOn or eOff, all bytes over 13M memory installed are added to this object. The above listed values returned by this object will be reduced by the amount of memory added to PCL-RESOURCE-SAVING-MEMORY-SIZE and POSTSCRIPT-RESOURCE-SAVING-MEMORY-SIZE when RESOURCE-SAVING=eOn.
media_info	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3
media_modes	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.4
OCT media_names_available	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1.1	OCTET STRING	read-write	The value of this object controls which of the MEDIAx- NAME objects are supported. If a bit is set to zero, then attempting to get or set the corresponding MEDIAx- NAME objects will return . Additional information: Setting a bit to one will cause the corresponding MEDIAn- objects to be available (attempting to access an unavailable object will return ). MEDIA1- objects are always present in LaserJet 4000 Series, as this is the default media. If this object is set to a value that does not include cMediaName1Available, that bit will be set and a status of will be returned. cMediaName12Available cannot be changed on LaserJet 4000 Series, as MediaName12 is not a supported Media Name for that product. Attempts to set cMediaName12Available will cause to be returned.
media_size	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5
INT media_size_west_edge_first_side_offset	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.2	INTEGER	read-write	Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the first printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the first printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. The values in the sub array index are from the media size table in the hpmib. The data for this object is stored in NVRAM.
INT media_size_west_edge_second_side_offset	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.5.3	INTEGER	read-write	Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the second printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the second printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. The values in the sub array index are from the media size table in the hpmib. The data for this object is stored in NVRAM.
media1	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1
INT media1_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: The engine processing characteristics that are to be applied to this media type. Currently, 'engine processing characteristics' denotes changes to fusing temperature and/or transfer roller voltage. The data for this object is stored in NVRAM.
STR media1_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.1	DisplayString	read-only	Media 1 name. Additional information: The symbol set for this string is Roman-8.
INT media1_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.3	INTEGER	read-only	Number of sheets of media 1 that have been printed. The device POS should state whether this value is lost across a power cycle or kept in NVRAM. Additional information: For LaserJet 4050 Series this page count is saved in NVRAM after every 10 pages. The maximum value is 4,294,967,295 which will never be reached in normal operation. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by one. The data for this object is stored in NVRAM.
STR media1_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.1.2	DisplayString	read-only	Length restricted version of the media name 1. The length restriction is required to allow the media name to be displayed on the device's control panel. The device POS must state the maximum number of characters allowed. If the device also has a limitation on what characters in a character set can be used (e.g. only uppercase characters allowed), the POS should also state character restrictions. Additional information: The maximum supported string length is 9 characters. If the user entered string is too long, the device will store the first 9 characters and will return the status. The characters must be in the range 20H to 7FH except 5C cannot be used. The default symbol set is Roman-8 for English; additional legal symbol sets are ISOLatin5, ISOLatin2 and Windows31J. Setting this object with characters outside of the range or of an illegal symbol set will cause an error status of to be returned.
media10	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10
INT media10_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media10_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.1	DisplayString	read-only	Media 10 name. Additional information: See MEDIA1-NAME.
INT media10_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.3	INTEGER	read-only	Number of sheets of media 10 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media10_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.10.2	DisplayString	read-only	Length restricted version of the media name 10. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media11	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11
INT media11_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media11_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.1	DisplayString	read-only	Media 11 name. Additional information: See MEDIA1-NAME.
INT media11_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.3	INTEGER	read-only	Number of sheets of media 11 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media11_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.11.2	DisplayString	read-only	Length restricted version of the media name 11. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media13	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13
INT media13_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media13_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.1	DisplayString	read-write	Media 13 name. Additional information: The maximum supported string length is 24 bytes. If the user entered string is too long, the device will store the first 24 bytes and return the status. See CAUTION statement under Product Specific Use.
INT media13_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.3	INTEGER	read-only	Number of sheets of media 13 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media13_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.13.2	DisplayString	read-write	Length restricted version of the media name 13. See MEDIA1-SHORT-NAME for details. Additional information: The maximum supported string length is 9 characters. If the user entered string is too long, the device will store the first 9 characters and will return the status. The characters must be in the range 20H to 7FH except 5C cannot be used. The default symbol set is Roman-8 for English; additional legal symbol sets are ISOLatin5, ISOLatin2 and Windows31J. Setting this object with characters outside of the range or of an illegal symbol set will cause an error status of to be returned.
media14	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14
INT media14_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media14_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.1	DisplayString	read-write	Media 14 name. Additional information: See MEDIA13-NAME.
INT media14_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.3	INTEGER	read-only	Number of sheets of media 14 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA13-PAGE-COUNT.
STR media14_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.14.2	DisplayString	read-write	Length restricted version of the media name 14. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA13-SHORT-NAME.
media15	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15
INT media15_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media15_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.1	DisplayString	read-write	Media 15 name. Additional information: See MEDIA13-NAME.
INT media15_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.3	INTEGER	read-only	Number of sheets of media 15 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA13-PAGE-COUNT.
STR media15_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.15.2	DisplayString	read-write	Length restricted version of the media name 15. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA13-SHORT-NAME.
media16	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16
INT media16_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media16_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.1	DisplayString	read-write	Media 16 name. Additional information: See MEDIA13-NAME.
INT media16_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.3	INTEGER	read-only	Number of sheets of media 16 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA13-PAGE-COUNT.
STR media16_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.16.2	DisplayString	read-write	Length restricted version of the media name 16. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA13-SHORT-NAME.
media17	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17
INT media17_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media17_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.1	DisplayString	read-write	Media 17 name. Additional information: See MEDIA13-NAME.
INT media17_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.3	INTEGER	read-only	Number of sheets of media 17 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA13-PAGE-COUNT.
STR media17_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.17.2	DisplayString	read-write	Length restricted version of the media name 17. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA13-SHORT-NAME.
media2	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2
INT media2_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media2_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.1	DisplayString	read-only	Media 2 name. Additional information: See MEDIA1-NAME.
INT media2_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.3	INTEGER	read-only	Number of sheets of media 2 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media2_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.2.2	DisplayString	read-only	Length restricted version of the media name 2. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media3	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3
INT media3_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media3_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.1	DisplayString	read-only	Media 3 name. Additional information: See MEDIA1-NAME.
INT media3_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.3	INTEGER	read-only	Number of sheets of media 3 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media3_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.3.2	DisplayString	read-only	Length restricted version of the media name 3. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media4	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4
INT media4_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media4_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.1	DisplayString	read-only	Media 4 name. Additional information: See MEDIA1-NAME.
INT media4_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.3	INTEGER	read-only	Number of sheets of media 4 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media4_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.4.2	DisplayString	read-only	Length restricted version of the media name 4. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media5	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5
INT media5_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media5_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.1	DisplayString	read-only	Media 5 name. Additional information: See MEDIA1-NAME.
INT media5_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.3	INTEGER	read-only	Number of sheets of media 5 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media5_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.5.2	DisplayString	read-only	Length restricted version of the media name 5. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media6	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6
INT media6_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media6_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.1	DisplayString	read-only	Media 6 name. Additional information: See MEDIA1-NAME.
INT media6_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.3	INTEGER	read-only	Number of sheets of media 6 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media6_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.6.2	DisplayString	read-only	Length restricted version of the media name 6. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media7	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7
INT media7_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media7_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.1	DisplayString	read-only	Media 7 name. Additional information: See MEDIA1-NAME.
INT media7_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.3	INTEGER	read-only	Number of sheets of media 7 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media7_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.7.2	DisplayString	read-only	Length restricted version of the media name 7. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media8	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8
INT media8_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media8_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.1	DisplayString	read-only	Media 8 name. Additional information: See MEDIA1-NAME.
INT media8_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.3	INTEGER	read-only	Number of sheets of media 8 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media8_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.8.2	DisplayString	read-only	Length restricted version of the media name 8. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
media9	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9
INT media9_engine_media_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.4	INTEGER	read-write	The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.
STR media9_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.1	DisplayString	read-only	Media 9 name. Additional information: See MEDIA1-NAME.
INT media9_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.3	INTEGER	read-only	Number of sheets of media 9 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.
STR media9_short_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.3.9.2	DisplayString	read-only	Length restricted version of the media name 9. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.
mio	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3
mio1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1
STR mio1_manufacturing_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.3	DisplayString	read-only	Returns information describing the manufacture of the I/O card installed in MIO/EIO slot 1. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.
STR mio1_model_name	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.2	DisplayString	read-only	Returns product information identifying the I/O card. Example: XXXX
INT mio1_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.1.4	INTEGER	read-only	Returns an indication of the type of option installed in MIO/EIO slot 1. See SIMM1-TYPE for an explanation of the enumerations.
mio2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2
STR mio2_manufacturing_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.3	DisplayString	read-only	Returns information describing the manufacture of the I/O card installed in MIO/EIO slot 2. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.
STR mio2_model_name	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.2	DisplayString	read-only	Returns product information identifying the I/O card. Example: XXXX
INT mio2_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.3.2.4	INTEGER	read-only	Returns an indication of the type of option installed in MIO/EIO slot 2. See SIMM1-TYPE for an explanation of the enumerations.
STR model_name	1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.2	DisplayString	read-only	Identifies the device model name (e.g. ''DeskJet 1200C''). The string is as specific as possible. Capitalization and spacing should match family naming conventions. Products should note in POS if the model name on the HP corporate price list changes but the device reports the previous device name. If the model name changes based on the installed options, the POS should indicate if only the base model name is returned, or if the device senses the installed options and returns the correct model name. If possible, encode the model name in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: Since the value of this object is frequently used in displaying a list of printers, it is kept relatively short in case systems have limited width for their display area. The model name does not change based on sensing of installed options.
STR model_number	1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.1	DisplayString	read-only	Identifies the device model number as listed in the HP corporate price list (e.g. C2121A for DeskJet 500C). The string is as specific as possible. Products should note in POS if the model number on the CPL changes but the device reports the previous model number. If the model number changes based on the installed options, the POS should indicate if only the base model number is returned, or if the device senses the installed options and returns the correct model number. If possible, encode the model number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: The value of this object does not change based on the installed options. The default of this object is the same on all LaserJet 4050 Series printers.
INT mopy_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.2.4.1.1	INTEGER	read-write	Controls or reports how mopies are generated. eOff turns off the mopy feature. eAuto allows the device to determine the best method for generating mopies based on the device configuration. eStandard spools the I/O data and replays the I/O data multiple times to generate the mopies. eEnhanced spools the rasterized page images and replays the rasterized data to generate the mopies. Typically, the rasterized data will be larger and will allow all but the first mopy to print at speed. If the job being mopied is not extremely complex, then the first mopy will print at speed also.
INT mp_tray	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1.5	INTEGER	read-write	Returns or changes the value of the multi-purpose (MP) tray configuration variable. The MP tray can be configured to operate as an additional input tray (eCassette), a manual feed slot (eManual), or in a manner compatible with the LaserJet III manual feed slot (eFirst). If configured for eFirst, if media is present in the MP tray, that media is used (assuming the size matches and the print job didn't specify another tray) until the MP tray is empty. Additional information: The MP tray can be configured for use either as a paper cassette or as a priority manual feed tray. When the tray is configured as a manual feed tray, unsolicited status messages are not generated when there is no paper in the tray. LaserJet 4050 Series will pull media from TRAY 1 only if there is a sheet present and it matches the needed size and type.
net_peripheral	1.3.6.1.4.1.11.2.3.9
netdm	1.3.6.1.4.1.11.2.3.9.4
nfs_server	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2
INT nfs_server_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.1.1	INTEGER	read-only	The amount of memory, in bytes, used by the Network File System server to buffer file data. Additional information: Reports the amount of memory, in bytes, reserved for use by the NFS server. An unfortunate side effect of the implementation is initializing the mass storage device sets this object back to the factory default value. Also includes the memory used by other firmware components in addition to the NFS server. Returns status if attempting to access this object and there is no storage device is installed.
INT nfs_server_read_size	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.1.2	INTEGER	read-write	The maximum amount of data transferred in one NFS server read data call. Additional information: An unfortunate side effect of the implementation is initializing the mass storage device sets this object back to the factory default value. Returns status if attempting to access this object and there is no storage device is installed. Rebooting causes this value to reset to factory default. value 1500 snaps to 1500
INT nfs_server_statistic_current_memory_usage	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.2.4	INTEGER	read-only	A value indicating the number of bytes of RAM currently used by the NFS firmware. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT nfs_server_statistic_max_memory_usage	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.2.5	INTEGER	read-only	A value indicating the maximum number of bytes of RAM used by the NFS firmware. The POS should state if the value is reset to zero after a power cycle. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT nfs_server_statistic_successful	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.2.1	INTEGER	read-only	A counter indicating the number of NFS requests that completed without error. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT nfs_server_statistic_unsuccessful	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.2.2	INTEGER	read-only	A counter indicating the number of NFS requests that completed with an NFS status other than NFS_OK (0). The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
OCT nfs_server_test_return_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.1.4	OCTET STRING	write-only	This test object that will not be supported in any released product. Setting this object allows the next NFS call return code to be specified. The POS will specify the binary format. Additional information: A three byte binary value. The first byte indicates what procedure is being effected by this set. value \| function ------+------------------ 1 \| GetAttr 2 \| SetAttr 3 \| reserved 4 \| Lookup 5 \| reserved 6 \| Read 7 \| reserved 8 \| Write 9 \| Create 10 \| Remove 11 \| Rename 12 \| reserved 13 \| reserved 14 \| MkDir 15 \| RmDir 16 \| ReadDir 17 \| StatFS The second byte is the stat value returned by the next call to procedure specified by the value of the first byte. The second byte can not be zero. Refer to RFC 1094 for a list of stat values. The third byte indicates which call to the specified file system routine will fail. A value of one means the first call will fail. A value of two means the second call will fail, and so on. Writing this object causes any previous write to this object to be invalidated.
INT nfs_server_write_size	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.1.3	INTEGER	read-write	The maximum amount of data transferred in one NFS server write data call. Additional information: An unfortunate side effect of the implementation is initializing the mass storage device sets this object back to the factory default value. Returns status if attempting to access this object and there is no storage device is installed.
nm	1.3.6.1.4.1.11.2
INT north_edge_offset	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1.2	INTEGER	read-write	Returns or sets the number of 300 dpi dots by which the image is shifted. Shift is relative to the leading edge of the medium as the medium flows through the marking engine with the side to be imaged facing the observer. The leading edge is the North edge and the other edges are defined by the normal compass layout of directions with the compass facing the observer. The adjustment is for all pages printed. A positive value moves the image away from the leading edge of the medium. A negative value moves the image closer to the leading edge of the medium. The value 0 will return the image to its factory default position. Additional information: The value of this object is stored in NVRAM.
INT on_off_line	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2.5	INTEGER	read-write	To bring the PDL processing sub-system on or off line. If the device is a printer, then the printer does not process print job data when the printer is off line. PML communication persists. Additional information: When the printer is in the Offline state, printing will stop as soon as possible (no more sheets of media are pulled from input trays). The I/O is taken offline also. Setting to eOnline has the following affect: Printer will immediately go to or remain in the Online state; status is returned. If the printer's current state is Offline with a pending error condition that prevents the printer from going to the Online state, the printer will remain in the Offline state; status is returned Setting to eOffline has the following affect: Printer will immediately go to or remain in the Offline state; status is returned. If pages are being printed, those pages will complete with the printer in the Offline state. Setting to eOfflineAtEndOfJob has the following affect: If not in a job or already in the Offline state, the printer will immediately go to or remain in the Offline state; status is returned. If in a job and the current state is Online, the printer will remain in the Online state, with the value of this object as eOfflineAtEndOfJob, until the end of the job; status is returned. At the end of the job, the printer goes to the Offline state and the value of this object becomes eOffline. Setting this object to eOffline or eOnline before the end of the job causes the action for that value to be taken immediately.
outbin	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4
outbin1	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1
OCT outbin1_override_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.1.9	OCTET STRING	read-write	Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.
outbin3	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.3
OCT outbin3_error_info	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.3.12	OCTET STRING	read-only	A device specific description of the last error encountered for output bin 3. Each POS should document the meaning of all supported error information. Additional information: This is a description of the current error state of a finishing device. (ie stapler). If the bin does not support any finishing capabilities then the object will return . The possible return values are as follows: Byte1, Byte2, and Byte3 should be 0x00. as they are reserved for future use. Byte4 is a bit field that can be interpreted as follows: bit 0 -- unused bit 1 -- eBinderOut Out of staples bit 2 -- eBinderLimit Too many pages to finish bit 3 -- eBinderJam Staple jammed in stapler bit 4 -- eBinderAlign Pages aren't aligned correctly to finish. bit 5 -- unused bit 6 -- unused bit 7 -- unused NOTE: Because HP is marketing a device with a max of 16 bins the OUTBIN-MAXIMUM-BINDING objects are 3-18 but the external device specification requires support of up to 315 output bins. Therefore if these bins exist above 16, then the coresponding objects will also exist OUTBIN19-MAXIMUM-BINDING ... OUTBIN317-MAXIMUM-BINDING
INT outbin3_maximum_binding	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.3.10	INTEGER	read-only	The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: This is a read only object that returns the number of 20# pages that this bin can bind(i.e. staple). This number is used by the host applications to prevent jobs that exceed this amount from being sent to this bin. If this bin does not have a finishing function like stapling where this object is necessary the object will return . NOTE: Because HP is marketing a device with a max of 16 bins the OUTBIN-MAXIMUM-BINDING objects are 3-18 but the external device specification requires support of up to 315 output bins. Therefore if these bins exist above 16, then the coresponding objects will also exist OUTBIN19-MAXIMUM-BINDING ... OUTBIN317-MAXIMUM-BINDING
OCT outbin3_override_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.3.9	OCTET STRING	read-write	Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions. NOTE: Because HP is marketing a device with a max of 16 bins the OUTBIN-OVERRIDE-MODE objects are 3-18 but the external device specification requires support of up to 315 output bins. Therefore if these bins exist above 16, then the coresponding objects will also exist OUTBIN19-OVERRIDE-MODE through OUTBIN317-OVERRIDE-MODE The data for this object is stored in NVRAM.
INT outbin3_phd	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3.3.11	INTEGER	read-only	Provides the number of the Paper Handling Device that contains this output bin. Additional information: This object will return the the device number that contains this output bin. The envelope feed is considered PHD1 thus this object will return 2-6 depending on where in the device chain the bin exists. NOTE: Because HP is marketing a device with a max of 16 bins the OUTBIN-OVERRIDE-MODE objects are 3-18 but the external device specification requires support of up to 315 output bins. Therefore if these bins exist above 16, then the coresponding objects will also exist OUTBIN19-PHD through OUTBIN317-PHD
outbins	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.3
INT overflow_bin	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.1.4	INTEGER	read-write	Returns or sets the bin that will be used for additional sheets of media when the current bin is full and printing is allowed to continue. Additional information: The data for this object is stored in NVRAM.
STR override_media_name	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.2	DisplayString	read-write	Sets a string identifying the media name that is to be used in place of the currently requested media. The substitution will continue until another media is selected. If set to a named media that is not currently available the requested media is not overridden. Additional information: When a request is received to print on a size and type of media that is not currently available, this object contains the desired media name as set by the print job. This object should be set to a media name that is currently available in the printer. If a paper mount request is not pending, attempting to get or set this object will cause to be returned. Setting this object to a string other than one of the MEDIAn-NAME objects (MEDIA-NAMES-AVAILABLE is applied) will cause a status of to be returned.
INT override_media_size	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.3	INTEGER	read-write	Sets the media size that is to be used in place of the currently requested media size. Additional information: When a request is received to print on a size and type of media that is not currently available, this object contains the desired size as set by the print job. This object should be set to a media size that is currently available to the printer. If a paper mount request is not pending, attempting to get or set this object will cause to be returned.
INT pcl_default_font_height	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.13	INTEGER	read-write	Returns or changes the default PCL height. Height is an approximate measure of the body of the type in centipoints. A centipoint is 1/7200 inch. Height applies only to proportional fonts. Point size, in points, can be converted to font height, in centipoints, by multiplying the point size by 100. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return . ''Closest'' means the smallest absolute difference. Additional information: Supported values range from 400 to 99975, in increments of 25 units. Setting to an unsupported value causes the printer to substitute in a snap value and to return status. The snap values are as follow: =99975 snaps to 99975 Unsupported values in the range 400 to 99975 snap DOWN to the previous supported value (i.e 25293 snaps to 25275 or 75038 snaps to 75025).
INT pcl_default_font_number	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.15	INTEGER	read-write	Returns or changes the value of the default font number variable in NVRAM. Writing an unsupported value causes the printer to generate an . Additional information: Valid numbers or 0 - 255, but only font numbers that are included in the PCL FONT LIST are selectable.
INT pcl_default_font_source	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.14	INTEGER	read-write	Returns or changes the value of the default font source variable in NVRAM.
INT pcl_default_font_width	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.16	INTEGER	read-write	Returns or changes the default PCL font width. Width is expressed as the width of a character in centipoints. A centipoint is 1/7200 inch. Width applies only to fixed space fonts. Pitch, in character per inch, can be converted to font width, in centipoints, by dividing 7200 by the pitch. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return . ''Closest'' means the smallest absolute difference. Additional information: Setting to an unsupported value causes the printer to substitue in a snap value (listed below) and return status. The snap values for pitch are as follow: =9999 snaps to 9999
INT pcl_resource_saving_memory_size	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.2	INTEGER	read-write	Returns or changes the amount of resource saving memory set aside to hold permanent soft PCL resources. Additional information: The value returned by this object is the amount of Resource Saving memory currently dedicated to PCL. For a PCL-only printer, the value of this object is zero. All memory is dedicated to PCL, but it is not shown as such. If Postscript is installed, the default value of this object is as follows: 0 if RESOURCE-SAVING = eOff. 0 if less than 8 Megabytes of RAM is in the printer. 400K bytes if RAM >= 8 Megabytes and RESOURCE-SAVING = eOn. 400K bytes if RAM = 8 Megabytes and RESOURCE-SAVING = eAuto, plus 100K bytes for each Megabyte of RAM over 8 Megabytes. If RESOURCE-SAVING=eOn, this object can be used to set the amount of Resource Saving memory currently dedicated to PCL. The range of values supported by this object are: 0 bytes (which disables resource saving for PCL) 400K bytes through (400K bytes + MAXIMUM-RESOURCE-SAVING-MEMORY) in increments of 100K bytes. If a value is received that is greater than 0 and less than 400K bytes, it will be snapped to 400K bytes and a status of returned. If an unsupported value greater than 400K bytes is received, it will be snapped down to the nearest 100K value and a status of returned. Attempting to set this object when RESOURCE-SAVING is eAuto or eOff will cause a status of to be returned.
INT pcl_total_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3.5	INTEGER	read-only	Total number of PCL pages printed by the device. Additional information: In LaserJet 4050 Series the PCL page count is kept in NVRAM, and the NVRAM value is updated at least every 10 pages. NOTE: The value returned by this object will be incremented every page but if power is lost between NVRAM updates, up to 9 pages of the page count may be lost. The page count counter will be reset to zero after 16,777,215 (2^24-1) pages. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by two.
pdl	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3
pdl_pcl	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.3
pdl_postscript	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4
ph	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7
ph_devices	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3
ph2	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.2
ph3	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.3
ph4	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.4
ph5	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.5
ph6	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.6
phd	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5
phd1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.1
INT phd1_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.1.4	INTEGER	read-only	Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: The LaserJet 4000 Series envelope feeder has a single tray.
STR phd1_manufacturing_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.1.2	DisplayString	read-only	Returns information describing the manufacture of this particular PHD. May include serial number and firmware revision.
STR phd1_model	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.1.1	DisplayString	read-only	Returns product information identifying the PHD device. Example: XXXX
INT phd1_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.1.3	INTEGER	read-only	Returns an indication of the type of option installed as PHD 1. See SIMM1-TYPE for an explanation of the enumerations. Additional information: Returns an indication of whether or not the envelope feeder is installed on the printer. A value of eEmpty means that the envelope feeder is not installed.
phd2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2
INT phd2_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2.4	INTEGER	read-only	Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least one (1) external paper handling device (EPHD) is attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD2-TYPE) for the first EPHD in the device chain.
OCT phd2_device_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.2.4	OCTET STRING	read-only	This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the first paper handling device. Currently, the printer allocates 16 bytes for each device.
OCT phd2_device_specific_command	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.2.2	OCTET STRING	write-only	This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the first device.
STR phd2_manufacturing_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2.2	DisplayString	read-only	Returns information describing the manufacture of PHD 2. May include serial number and firmware revision. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the first paper handling device.
STR phd2_model	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2.1	DisplayString	read-only	Returns product information identifying PHD device 2. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the first paper handling device in the device chain.
INT phd2_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.2.3	INTEGER	read-only	Returns an indication of the type of option installed in PHD interface 2. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the device is an input device, an output device, or an unknown device which may be developed in the future.
phd3	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3
INT phd3_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3.4	INTEGER	read-only	Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least two (2) external paper handling devices (EPHD) are attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD3-TYPE) for the second EPHD in the device chain.
OCT phd3_device_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.3.4	OCTET STRING	read-only	This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the second paper handling device. Currently, the printer allocates 16 bytes for each device.
OCT phd3_device_specific_command	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.3.2	OCTET STRING	write-only	This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the second device.
STR phd3_manufacturing_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3.2	DisplayString	read-only	Returns information describing the manufacture of PHD 3. May include serial number and firmware revision. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the second paper handling device.
STR phd3_model	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3.1	DisplayString	read-only	Returns product information identifying PHD device 3. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the second paper handling device in the device chain.
INT phd3_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.3.3	INTEGER	read-only	Returns an indication of the type of option installed in PHD interface 3. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least two (2) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the second device is an input device, an output device, or an unknown object which may be developed in the future.
phd4	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4
INT phd4_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4.4	INTEGER	read-only	Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least three (3) external paper handling devices (EPHD) are attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD4-TYPE) for the third EPHD in the device chain.
OCT phd4_device_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.4.4	OCTET STRING	read-only	This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the second paper handling device. Currently, the printer allocates 16 bytes for each device.
OCT phd4_device_specific_command	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.4.2	OCTET STRING	write-only	This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the third device.
STR phd4_manufacturing_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4.2	DisplayString	read-only	Returns information describing the manufacture of PHD 4. May include serial number and firmware revision. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the third paper handling device.
STR phd4_model	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4.1	DisplayString	read-only	Returns product information identifying PHD device 4. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the third paper handling device in the device chain.
INT phd4_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.4.3	INTEGER	read-only	Returns an indication of the type of option installed in PHD interface 4. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least three (3) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the third device is an input device, an output device, or an unknown device which may be developed in the future.
phd5	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5
INT phd5_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5.4	INTEGER	read-only	Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least four (4) external paper handling devices (EPHD) are attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD5-TYPE) for the fourth EPHD in the device chain.
OCT phd5_device_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.5.4	OCTET STRING	read-only	This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the second paper handling device. Currently, the printer allocates 16 bytes for each device.
OCT phd5_device_specific_command	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.5.2	OCTET STRING	write-only	This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the fourth device.
STR phd5_manufacturing_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5.2	DisplayString	read-only	Returns information describing the manufacture of PHD 5. May include serial number and firmware revision. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the fourth paper handling device.
STR phd5_model	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5.1	DisplayString	read-only	Returns product information identifying PHD device 3. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the fourth paper handling device in the device chain.
INT phd5_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.5.3	INTEGER	read-only	Returns an indication of the type of option installed in PHD interface 5. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least four (4) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the fourth device is an input device, an output device, or an unknown device which may be developed in the future.
phd6	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6
INT phd6_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6.4	INTEGER	read-only	Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least five (5) external paper handling devices (EPHD) are attached to the printer, then this object will exist, otherwise should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD6-TYPE) for the fifth EPHD in the device chain.
OCT phd6_device_memory	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.6.4	OCTET STRING	read-only	This object is used to read the current values stored in shared memory available from the paper handling device. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the current memory stored in the printer's NVRAM (non-volatile RAM) for the second paper handling device. Currently, the printer allocates 16 bytes for each device.
OCT phd6_device_specific_command	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.7.3.6.2	OCTET STRING	write-only	This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise will be returned. Since the data formats can vary from device to device, this information must be documented for each device by the manufacturer of the device. If the device does not support this command, then an error message will be returned. Since it will usually take longer to send this command to the device than PML allows for operations, this object will have a return value that does not necessarily match the value currently received by the fifth device.
STR phd6_manufacturing_info	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6.2	DisplayString	read-only	Returns information describing the manufacture of PHD 6. May include serial number and firmware revision. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns the name of the manufacturer of the fifth paper handling device.
STR phd6_model	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6.1	DisplayString	read-only	Returns product information identifying PHD device 6. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns product information about the fifth paper handling device in the device chain.
INT phd6_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.5.6.3	INTEGER	read-only	Returns an indication of the type of option installed in PHD interface 6. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least five (5) external paper handling devices are attached to the printer, then this object will exist, otherwise should be returned. This object returns whether the fifth device is an input device, an output device, or an unknown device which may be developed in the future.
pjl	1.3.6.1.4.1.11.2.3.9.4.2.1.3.5
INT pjl_password	1.3.6.1.4.1.11.2.3.9.4.2.1.3.5.1	INTEGER	read-only	Returns PJL password, if the password is not set (zero). If the password is set, then attempting to retrieve the password causes an to occur and will return the .
port1	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1
INT port1_parallel_bidirectionality	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.5	INTEGER	read-write	Returns or changes whether the parallel I/O port supports bidirectional communication for port 1. This object is only supported if this port is a parallel port. Additional information: A get on this object returns the current mode for the parallel port. Setting this object specifies whether or not bidirectional communications will be allowed.
INT port1_parallel_speed	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3.1.4	INTEGER	read-write	Returns or changes the maximum parallel I/O port speed, for port 1. This object is only supported if this port is a parallel port. An eSlow setting causes a 10 us busy pulse per received byte of data. An eFast setting causes a 1.5 us busy pulse per received byte of data. In rare cases, setting this value to eFast can cause the parallel port to no longer transfer data reliably.
ports	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.3
INT postscript_print_errors	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.11	INTEGER	read-write	Returns or changes the value of the print PostScript errors setting. If eOn, PostScript prints an error page showing the error encountered and the stack at the time of the error. Additional information: This object is only supported if the PostScript option is installed.
INT postscript_resource_saving_memory_size	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.2	INTEGER	read-write	Returns or changes the amount of resource saving memory set aside to hold permanent soft PostScript resources. Additional information: The value returned by this object is the amount of Resource Saving memory currently dedicated to Postscript. If Postscript is installed, the default value of this object is as follows: 0 if RESOURCE-SAVING = eOff. 0 if less than 8 Megabytes of RAM is in the printer. 400K bytes if RAM >= 8 Megabytes and RESOURCE-SAVING = eOn. 400K bytes if RAM = 8 Megabytes and RESOURCE-SAVING = eAuto, plus 100K bytes for each Megabyte of RAM over 8 Megabytes. If RESOURCE-SAVING=eOn, this object can be used to set the amount of Resource Saving memory currently dedicated to PCL. The range of values supported by this object are: 0 bytes (which disables resource saving for Postscript) 400K bytes through (400K bytes + MAXIMUM-RESOURCE-SAVING-MEMORY) in increments of 100K bytes. If a value is received that is greater than 0 and less than 400K bytes, it will be snapped to 400K bytes and a status of returned. If an unsupported value greater than 400K bytes is received, it will be snapped down to the nearest 100K value and a status of returned. Attempting to set this object when RESOURCE-SAVING is eAuto or eOff will cause a status of to be returned.
INT postscript_total_page_count	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.4.5	INTEGER	read-only	Total number of PostScript pages printed by the device. Additional information: This object is only supported if the PostScript option is installed. In LaserJet 4050 Series the count is kept in NVRAM, and the NVRAM value is updated at least every 10 sheets. NOTE: The value returned by this object will be incremented every sheet but if power is lost between NVRAM updates up to 9 sheets of the count may be lost. The counter will be reset to zero after 16,777,215 (2^24-1) pages.
INT print_density	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1.5	INTEGER	read-write	Returns or sets the print density setting. Print density is the instantaneous amount of marking agent applied to the paper while printing. A value of zero has the lowest print density, yielding a lighter page. A value of 10 has the highest print density, yielding a darker page. Each POS should document what values in the 0 to 10 range are supported. Additional information: When this value is written, the page pipeline will be flushed (all pages being printed are completed, no new ones are started), the new density setting is set and printing resumes. The acutal change in print density may be gradual over several pages. The supported values are 1 through 5. Setting to an unsupported value causes the printer to substitue in a a snap value and to return status. The snap values are as follows: 5 snaps to 5.
print_engine	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1
STR print_engine_revision	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2.26	DisplayString	read-only	Print engine revision string. Additional information: The symbol set for this string is Roman-8. Converts engine revision number to a string and returns it.
INT print_internal_page	1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.2	INTEGER	read-write	Writing this object to a value other than eNotPrintingAnInternalPage causes the device to attempt to print an internally generated page. Reading this object provides an indication what internally generated page is currently being printed, if any. The actual page is device specific. Some devices may support continuously printing an internally generated page. Setting this object to eNotPrintingAnInternalPage terminates continuously printing internally generated pages. An internally generated page may not be allowed to be printed at any arbitrary time; under what conditions it will succeed or fail is device specific. If the device supports the requested page, but can not start printing the page when requested, the device will respond with . RECOMMENDATION: If the device is ready (i.e. the NOT- READY-PRINTER object does not contain any items, except maybe being off-line) and is idle (i.e. the NOT-IDLE object does not contain any items), this request should always succeed. This provides a mechanism for driver writers to always determine if the action will succeed or not. Additional information: Previous products used ePCLDemoPage1ConfigurationPage(300) for the Configuration or Self Test page. This product uses eDeviceDemoPage1ConfigurationPage(3). LaserJet 4050 Series does not support continuously printing a demo page. When this object is set to a valid value, the status returned is and the value returned is ePrintingAnUnknownInternalPage. If the printer is idle, the page will be printed immediately. If the printer is currently printing another job, the internal page requested will not print until that job is finished. Setting this object to a valid value causes the desired page to be formatted and put in the printer's print queue. While the page is being formatted a get on this object will return the value ePrintingAnUnknownInternalPage. Once the page (or pages) is finished being formatted, this object returns a value of eNotPrintingAnInternalPage, even though the page may not have finished being printed. Setting this object multiple times will queue up the requests, but only a limited number will be queued. Once the queue is full, additional requests will be ignored.
print_media	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8
OCT printed_media_duplex_charge	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.4	OCTET STRING	read-write	Charge for each duplex page printed in this media size. Additional information: The click charges for duplex printed media.
INT printed_media_duplex_count	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.3	INTEGER	read-only	Total number of duplex pages printed in this media size.
OCT printed_media_simplex_charge	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.2	OCTET STRING	read-write	Charge for each simplex page printed in this media size.
INT printed_media_simplex_count	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.1	INTEGER	read-only	Total number of simplex pages printed in this media size. Additional information: The 5 usage (simplex/duplex count, simplex/duplex click charge and paper size total) objects described here and below detail the usage for the printer for each paper size defined in the PCL Implementor's Guide and in the Media Size Table in the hpmib.txt. The OID binding is based on the click attribute and paper size. For example: The format for the OID is as follows: 3.4.1.5.x.y \| \| \| \| \ / \| paper size / \ PRINTER-CLICK_TOTALS ROOT \ OID click attribute 1..5 x values are 1..5: 1) simplex count 2) simplex click charge 3) duplex count 4) duplex click charge 5) printer or scanner paper size total (i.e. depends if the root OID is referrring to the printer or scanner). y : paper size as defined in the Media Size Table in the hpmib.txt
OCT printed_media_total_charge	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1.5	OCTET STRING	read-only	The total charge for pages printed in this media size.
printed_media_usage	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.1
printer_accounting	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1
printmib	1.3.6.1.4.1.11.2.3.9.4.2.2
processing_subsystem	1.3.6.1.4.1.11.2.3.9.4.2.1.3
prtAlert	1.3.6.1.4.1.11.2.3.9.4.2.2.18
INT prtalertallevents	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.19	INTEGER	read-only	A running counter of the total number of alert event entries (critical and non-critical) that have been recorded in the alert table Refer to Standard Printer MIB for more details. Additional information: This object is set to zero every time the printer is turned on. (It is not persistent through a power-cycle.)
INT prtalertcode	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.7	INTEGER	read-only	See associated textual convention PrtAlertCodeTC Refer to Standard Printer MIB for more details.
INT prtalertcriticalevents	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.18	INTEGER	read-only	A running counter of the number of critical alert events that have been recorded in the alert table. The value of this object is RESET in the event of a power cycle operation (i.e., the value is not persistent. Refer to Standard Printer MIB for more details. Additional information: This object is set to zero every time the printer is turned on.
OCT prtalertdescription	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.8	OCTET STRING	read-only	A description of this alert entry in the localization specified by prtGeneralCurrentLocalization. The description is provided by the printer to further elaborate on the enumerated alert or provide information in the case where the code is classified as `other' or `unknown'. The printer is required to return a description string but the string may be a null string. Refer to Standard Printer MIB for more details.
prtAlertEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1
INT prtalertgroup	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.4	INTEGER	read-only	The type of sub-unit within the printer model that this alert is related. Input, output, and markers are examples of printer model groups, i.e., examples of types of sub-units. Wherever possible, these enumerations match the sub-identifier that identifies the relevant table in the printmib. Refer to Standard Printer MIB for more details.
INT prtalertgroupindex	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.5	INTEGER	read-only	An index of the row within the principle table in the group identified by prtAlertGroup that represents the sub-unit of the printer that caused this alert. The combination of the prtAlertGroup and the prtAlertGroupIndex defines exactly which printer sub-unit caused the alert.; for example, Input #3, Output #2, and Marker #1. Every object in this MIB is indexed with hrDeviceIndex and optionally, another index variable. If this other index variable is present in the table that generated the alert, it will be used as the value for this object. Otherwise, this value shall be -1. Refer to Standard Printer MIB for more details.
INT prtalertlocation	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.6	INTEGER	read-only	The sub-unit location that is defined by the printer manufacturer to further refine the location of this alert within the designated sub-unit. The location is used in conjunction with the Group and GroupIndex values; for example, there is an alert in Input #2 at location number 7. The value (-2) indicates unknown Refer to Standard Printer MIB for more details.
INT prtalertseveritylevel	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.2	INTEGER	read-only	The level of severity of this alert table entry. The printer determines the severity level assigned to each entry into the table. Refer to Standard Printer MIB for more details.
prtAlertTable	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1
INT prtalerttime	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.9	INTEGER	read-only	The value of sysUpTime at the time that this alert was generated. Refer to Standard Printer MIB for more details.
INT prtalerttraininglevel	1.3.6.1.4.1.11.2.3.9.4.2.2.18.1.1.3	INTEGER	read-only	See textual convention PrtAlertTrainingLevelTC Refer to Standard Printer MIB for more details. Additional information: The value of this object depends on the alert. Some examples: ePfieldService: Marker failure. ePtrained: Toner low. ePuntrained: Paper low/out. ePmanagement: Configuration change.
prtChannel	1.3.6.1.4.1.11.2.3.9.4.2.2.14
INT prtchannelcurrentjobcntllangindex	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1.4	INTEGER	read-only	The value of prtInterpreterIndex corresponding to the Control Language Interpreter for this channel. This interpreter defines the syntax used for control functions, such as querying or changing environment variables and identifying job boundaries (e.g. PJL, PostScript, NPAP). Must be 1 or greater. Refer to Standard Printer MIB for more details. Additional information: This object points to the PJL language. It is read-only because PJL is the printer's only job control language.
INT prtchanneldefaultpagedesclangindex	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1.5	INTEGER	read-write	The value of prtInterpreterIndex corresponding to the Page Description Language Interpreter for this channel. This interpreter defines the default Page Description Language interpreter to be used for the print data unless the Control Language is used to select a specific interpreter (e.g., PCL, PostScript Language, auto-sense). Must be 1 or greater. Refer to Standard Printer MIB for more details. Additional information: Replaces PML DEFAULT-PDL. The default points to the automatic language switcher. If this object is changed for one channel, all channels will be changed.
prtChannelEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1
INT prtchannelifindex	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1.7	INTEGER	read-only	The value of ifIndex (in the ifTable; see the interface section of MIB-2/RFC 1213) which corresponds to this channel. When more than one row of the ifTable is relevant, this is the index of the row representing the topmost layer in the interface hierarchy. A value of zero indicates that no interface is associated with this channel. Refer to Standard Printer MIB for more details. Additional information: IIO-based channels provide their own values for this object.
OCT prtchannelinformation	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1.9	OCTET STRING	read-only	Auxiliary information to allow a printing application to use the channel for data submission to the printer. An application capable of using a specific PrtChannelType should be able to use the combined information from the prtChannelInformation and other channel and interface group objects to 'bootstrap' its use of the channel. prtChannelInformation is not intended to provide a general channel description, nor to provide information that is available once the channel is in use. The encoding and interpretation of the prtChannelInformation object is specific to channel type. The description of each PrtChannelType enum value for which prtChannelInformation is defined specifies the appropriate encoding and interpretation, including interaction with other objects. For channel types that do not specify a prtChannelInformation value, its value shall be null (0 length). When a new PrtChannelType enumeration value is registered, its accompanying description must specify the encoding and interpretation of the prtChannelInformation value for the channel type. prtChannelInformation semantics for an existing PrtChannelType may be added or amended in the same manner as described in section 2.4.1 for type 2 enumeration values. The prtChannelInformation specifies values for a collection of channel attributes, represented as text according to the following rules: 1. The prtChannelInformation is coded in the NVT ASCII character set. It is not affected by localization. 2. The prtChannelInformation is a list of entries representing the attribute values. Each entry consists of the following items, in order: a. a keyword, composed of alphabetic characters (A-Z, a-z), that identifies a channel attribute, b. an Equals Sign (=) to delimit the keyword, c. a data value, consisting of NVT ASCII graphics characters (codes 32-126), d. a Line Feed character (code 10) to delimit the data value. No other characters shall be present. Keywords are case-sensitive. Conventionally, keywords are capitalized (including each word of a multi-word keyword), and, since they occupy space in the prtChannelInformation, they are kept short. 3. If a channel attribute has multiple values, it is represented by multiple entries with the same keyword, each specifying one value. Otherwise, there shall be at most one entry for each attribute. 4. By default, entries may appear in any order. If there are ordering constraints for particular entries, these must be specified in their definitions. 5. The prtChannelInformation value may represent information that is not normally coded in textual form, or that is coded in a character set other than NVT ASCII. In these cases, whatever symbolic representation is conventionally used for the information should be used for encoding the prtChannelInformation. (For instance, a binary port value might be represented as a decimal number, Unicode would be represented in UTF-8 format.) 6. For each PrtChannelType for which prtChannelInformation entries are defined, the descriptive text associated with the PrtChannelType enumeration value shall specify the following information for each entry: Title: Brief description phrase, e.g.: 'Port name', 'Service Name', Keyword: The keyword value, eg: 'Port', 'Service' Syntax: The encoding of the entry value, if it cannot be directly represented by NVT ASCII, Status: 'Mandatory', 'Optional', or 'Conditionally Mandatory', Multiplicity: 'Single' or 'Multiple', to indicate whether the entry may be present multiple times, Description: Description of the use of the entry, other information required to complete the definition (e.g.: ordering contstraints, interactions between entries). Applications that interpret prtChannelInformation should ignore unrecognized entries, so they are not affected if new entry types are added. Refer to Standard Printer MIB for more details. Additional information: IIO-based channels provide their own values for this object.
OCT prtchannelprotocolversion	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1.3	OCTET STRING	read-only	The version of the protocol used on this channel. The format used for version numbering depends on prtChannelType. Refer to Standard Printer MIB for more details. Additional information: This object, in conjunction with prtChannelType, replaces the PML object PORTn-DESCRIPTION. IIO-based channels provide their own values. The channel 1 value includes (separated by semi colons) different aspectsof the spec: electrical: logical; and physical connector.
INT prtchannelstate	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1.6	INTEGER	read-only	The state of this print data channel. The value determines whether control information and print data is allowed through this channel or not. Refer to Standard Printer MIB for more details. Additional information: IIO-based channels provide their own values for this object. The base-printer's ports always report a value of ePprintDataAccepted. If the printer is offline, that is detected by reading the Host Resources General Printer Status objects, not by reading this object.
INT prtchannelstatus	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1.8	INTEGER	read-only	The current status of the channel. Refer to Standard Printer MIB for more details. Additional information: IIO-based channels provide their own values for this object.
prtChannelTable	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1
INT prtchanneltype	1.3.6.1.4.1.11.2.3.9.4.2.2.14.1.1.2	INTEGER	read-only	The type of this print data channel. This object provides the linkage to ChannelType-specific groups that may (conceptually) extend the prtChannelTable with additional details about that channel. Refer to Standard Printer MIB for more details. Additional information: This object, in conjunction with prtChannelProtocolVersion, replaces the PML object PORTn-DESCRIPTION. IIO based channels provide their own values.
INT prtconsolecolor	1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1.4	INTEGER	read-only	The color of this light. Refer to Standard Printer MIB for more details.
OCT prtconsoledescription	1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1.5	OCTET STRING	read-only	The vendor description or label of this light in the localization specified by prtConsoleLocalization. Refer to Standard Printer MIB for more details.
INT prtconsoledisable	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.13	INTEGER	read-write	If the object prtConsoleDisable has value 'operatorConsoleDisabled' then input is not accepted from the operator console. If the object prtConsoleDisable has the value 'operatorConsoleEnabled' then input is accepted from the operator console. If the object prtConsoleDisable has the value 'operatorConsoleEnabledLevel1','operatorConsoleEnabledLevel2' or 'operatorConsoleEnabledLevel3' then limited input is accepted from the operator console; the limitations are product specific, however, the limitations are generally less restrictive for operatorConsoleEnabledLevel1 than for operatorConsoleEnabledLeve2, which is less restrictive than operatorConsoleEnabledLevel3. The value of the prtConsoleDisable object is a type-2 enumeration. Refer to Standard Printer MIB for more details. Additional information: If the object prtConsoleDisable has value 'ePoperatorConsoleDisabled' then manual input is not accepted from the operator console. If the object prtConsoleDisable has the value 'ePoperatorConsoleEnabled' then manual input is accepted from the operator console. The following menus are locked with these corresponding values: ePoperatorConsoleEnabled (no locking) ePoperatorConsoleEnabledLevel1 (minimal locking) RESETS MENU CONFIGURATION MENU I/O MENU ePoperatorConsoleEnabledLevel2 (moderate locking) PRINT QUALITY MENU PAPER HANDLING MENU menus in level 1 ePoperatorConsoleDisabled (maximum locking) PRINTING MENU INFORMATION MENU Job Cancel menus in levels 1 and 2
prtConsoleDisplayBuffer	1.3.6.1.4.1.11.2.3.9.4.2.2.16
prtConsoleDisplayBufferEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.16.5.1
prtConsoleDisplayBufferTable	1.3.6.1.4.1.11.2.3.9.4.2.2.16.5
OCT prtconsoledisplaybuffertext	1.3.6.1.4.1.11.2.3.9.4.2.2.16.5.1.2	OCTET STRING	read-only	The content of a line in the logical display buffer of the operator's console of the printer. When a write operation occurs, normally a critical message, to one of the LineText strings, the agent should make that line displayable if a physical display is present. Writing a zero length string clears the line. It is an implementation-specific matter as to whether the agent allows a line to be overwritten before it has been cleared. Printer generated strings shall be in the localization specified by prtConsoleLocalization. Management Application generated strings should be localized by the Management Application. Refer to Standard Printer MIB for more details. Additional information: Replaces PML STATUS-MSG-LINE1-PART1 and STATUS-MSG-LINE2-PART1 (read functionality). The proprietary objects BACKGROUND-STATUS-MSG-LINE1-PART1 and BACKGROUND-STATUS-MSG-LINE2-PART1 should be used to write messages to the control panel display. prtConsoleDisplayBufferText.1.[1..6] maps to logical lines 1-6 of the display. Most of the time the display will show a single one or two line message. This message can be retrieved by reading prtConsoleDisplayBufferText.1.1 and prtConsoleDisplayBufferText.1.2. In this case prtConsoleDisplayBufferText.1.[3..6] will be NULL. If prtConsoleDisplayBufferText.1.3 or prtConsoleDisplayBufferText.1.4 is not NULL, the display will be alternating. If prtConsoleDisplayBufferText.1.[5..6] are NULL, the display will alternate prtConsoleDisplayBufferText.1.[1..2] with prtConsoleDisplayBufferText.1.[3..4]. If prtConsoleDisplayBufferText.1.5 or prtConsoleDisplayBufferText.1.6 is not NULL, the display will show prtConsoleDisplayBufferText.1.[1..2] then prtConsoleDisplayBufferText.1.[3..4] then prtConsoleDisplayBufferText.1.[5..6]. The display will alternate between line pairs at three second intervals.
prtConsoleLightEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1
prtConsoleLights	1.3.6.1.4.1.11.2.3.9.4.2.2.17
prtConsoleLightTable	1.3.6.1.4.1.11.2.3.9.4.2.2.17.6
INT prtconsolelocalization	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.10	INTEGER	read-write	The value of the prtLocalizationIndex corresponding to the language, country, and character set to be used for the console. This localization applies both to the actual display on the console as well as the encoding of these console objects in management operations. Refer to Standard Printer MIB for more details. Additional information: The value of this object is saved in NVRAM. If a localized string is currently being displayed on the control panel by the device, changing this object will cause the displayed string to be changed to its new value. If this object is changed while the printer is processing a page that contains localized strings, the results are undefined.
INT prtconsolenumberofdisplaychars	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.12	INTEGER	read-only	The number of characters per line displayed on the physical display. This value is 0 if there are no lines on the physical display or if there is no physical display Refer to Standard Printer MIB for more details.
INT prtconsolenumberofdisplaylines	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.11	INTEGER	read-only	The number of lines on the printer's physical display. This value is 0 if there are no lines on the physical display or if there is no physical display Refer to Standard Printer MIB for more details. Additional information: The printer has two physical lines on the display, however, in many cases up to four seperate lines of text may be displayed by alternating pairs of lines every three seconds. Thus the display really has four logical lines for displaying messages. This object will return the number of logical display lines supported by the printer.
INT prtconsoleofftime	1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1.3	INTEGER	read-only	This object, in conjunction with prtConsoleOnTime, defines the current status of the light. If both prtConsoleOnTime and prtConsoleOffTime are non-zero, the lamp is blinking and the values presented define the on time and off time, respectively, in milliseconds. If prtConsoleOnTime is zero and prtConsoleOffTime is non-zero, the lamp is off. If prtConsoleOffTime is zero and prtConsoleOnTime is non-zero, the lamp is on. If both values are zero the status of the lamp is undefined. Refer to Standard Printer MIB for more details. Additional information: There are three control panel LED's: Ready (1), Data (2), and Attention (3). When an LED blinks, it is typically on for one half second and off for one half second. The value used for this object is 500 when the LED is off or blinking, otherwise it is zero.
INT prtconsoleontime	1.3.6.1.4.1.11.2.3.9.4.2.2.17.6.1.2	INTEGER	read-only	This object, in conjunction with prtConsoleOffTime, defines the current status of the light. If both prtConsoleOnTime and prtConsoleOffTime are non-zero, the lamp is blinking and the values presented define the on time and off time, respectively, in milliseconds. If prtConsoleOnTime is zero and prtConsoleOffTime is non-zero, the lamp is off. If prtConsoleOffTime is zero and prtConsoleOnTime is non-zero, the lamp is on. If both values are zero the status of the lamp is undefined. Refer to Standard Printer MIB for more details. Additional information: There are three control panel LED's: Ready (1), Data (2), and Attention (3). When an LED blinks, it is typically on for one half second and off for one half second. The value used for this object is 500 when the LED is on or blinking, otherwise it is zero.
prtCover	1.3.6.1.4.1.11.2.3.9.4.2.2.6
OCT prtcoverdescription	1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1.2	OCTET STRING	read-only	The manufacturer provided cover sub-mechanism name in the localization specified by prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details.
prtCoverEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1
INT prtcoverstatus	1.3.6.1.4.1.11.2.3.9.4.2.2.6.1.1.3	INTEGER	read-only	The status of this cover sub-unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML NOT-READY-DOOR-OPEN.
prtCoverTable	1.3.6.1.4.1.11.2.3.9.4.2.2.6.1
prtDeviceRefEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.5.3.1
INT prtdevicerefindex	1.3.6.1.4.1.11.2.3.9.4.2.2.5.3.1.2	INTEGER	read-only	The value of the hrDeviceIndex of the printer device that this deviceEntry is associated with. Refer to Standard Printer MIB for more details. Additional information (mass storage) : Constant. The index indicates the hrDeviceIndex for this mass storage device. The value indicates the hrDeviceIndex for the printer which uses this mass storage device. Returns status if attempting to perform a Get on this OID with no mass storage device installed.
prtDeviceRefTable	1.3.6.1.4.1.11.2.3.9.4.2.2.5.3
prtGeneral	1.3.6.1.4.1.11.2.3.9.4.2.2.5
INT prtgeneralbannerpage	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.15	INTEGER	read-only	Used to enable or disable printing banner pages at the beginning of jobs. This is a master switch which applies to all jobs, regardless of interpreter. Refer to Standard Printer MIB for more details.
INT prtgeneralconfigchanges	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.1	INTEGER	read-only	Counts configuration changes that change the capabilities of a printer, such as the addition/deletion of input/output bins, the addition/deletion of interpreters, or changes in media size. Such changes will often affect the capability of the printer to service certain types of print jobs. Management applications may cache infrequently changed configuration information about sub-units on the printer. This object should be incremented whenever the agent wishes such applications to invalidate that cache and re-download all of this configuration information, thereby signaling a change in the printer's configuration. For example, if an input tray that contained paper of different dimensions was added, this counter would be incremented. As an additional example, this counter would not be incremented when an input tray is removed or the level of an input device changes. Refer to Standard Printer MIB for more details. Additional information: This is a 32 bit counter (unsigned). When it reaches its maximum value, it will roll to zero.
INT prtgeneralcurrentlocalization	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.2	INTEGER	read-write	The value of the prtLocalizationIndex corresponding to the current language, country, and character set to be used for localized string values that are identified as being dependent on the value of this object. Note that this object does not apply to localized strings in the prtConsole group or to any object that is not explicitly identified as being localized according to prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details. Additional information: The value of this object is saved in NVRAM.
OCT prtgeneralcurrentoperator	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.4	OCTET STRING	read-write	The name of the person who is responsible for operating this printer. It is suggested that this string include information that would enable other humans to reach the operator, such as a phone number. As a convention to facilitate automatic notification of the operator by the agent or the network management station, the phone number, fax number or email address should be placed on a separate line starting with ASCII LF (hex 0x0A) and the ASCII text string (without the quotes): 'phone: ', 'fax: ', and 'email: ', respectively. Phone numbers may contain digits, whitespace and parentheses, which shall be ignored. Phone numbers may also include ASCII comma characters(hex 2C) that are used to indicate a two-second pause during the dialing sequence. If either the phone, fax, or email information is not available, then a line should not be included for this information. NOTE: For interoperability purposes, it is advisable to use email addresses formatted according to RFC 822 requirements. Refer to Standard Printer MIB for more details. Additional information: Replaces PML SYSTEM-CONTACT. The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user entered string is too long, the device will store as much as possible and will return the status.
prtGeneralEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1
OCT prtgeneralprintername	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.16	OCTET STRING	read-write	An administrator-specified name for this printer. Depending upon implementation of this printer, the value of this object may or may not be same as the value for the MIB-II 'SysName' object. Refer to Standard Printer MIB for more details. Additional information: The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user-entered string is too long, the device will store as much as possible and will return the status. The value of this object is saved over a power cycle.
INT prtgeneralreset	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.3	INTEGER	read-write	Setting this value to `powerCycleReset', `resetToNVRAM', or `resetToFactoryDefaults' will result in the resetting of the printer. When read, this object will always have the value `notResetting(3)', and a SET of the value `notResetting' shall have no effect on the printer. Some of the defined values are optional. However, every implementation must support at least the values `notResetting' and 'resetToNVRAM'. Refer to Standard Printer MIB for more details. Additional information: Replaces PML USER-NVRAM-RESET and POWER-ON-RESET. The, the following sequence of events occur when this object is set to ePpowerCycleReset, ePresetToNVRAM, or ePresetToFactoryDefaults: 1. Wait until a job boundary. 2. The paper path is flushed. 3. The printer is reset per the request. The printer will respond to PML requests up to this point in time. All settings will make the printer go thru its power-on initialization routines and I/O cards are reset. When this object is set to ePpowerCycleReset or ePresetToNVRAM, the printer performs its power on initialization routines. I/O cards are reset, although NVRAM on the cards is not changed, and all I/O buffers are flushed. This is equivalent to turning the printer off and then on again. Setting this object to ePresetToFactoryDefaults causes the same action as ePpowerCycleReset exept that it also changes all configurable settings back to their factory defaults. It is equivalent to doing a Cold Reset from the control panel while turning on the printer.
OCT prtgeneralserialnumber	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.17	OCTET STRING	read-only	A recorded serial number for this device that indexes some type device catalog or inventory. This value is usually set by the device manufacturer but the MIB supports the option of writeability for this object for site-specific administration of device inventory or tracking. Refer to Standard Printer MIB for more details.
OCT prtgeneralserviceperson	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.5	OCTET STRING	read-write	The name of the person responsible for servicing this printer. It is suggested that this string include information that would enable other humans to reach the service person, such as a phone number. As a convention to facilitate automatic notification of the service person by the agent or a network management station, the phone number, fax number or email address should be placed on a separate line starting with ASCII LF (hex 0x0A) and the ASCII text string (without the quotes): 'phone: ', 'fax: ', and 'email: ', respectively. Phone numbers may contain digits, whitespace and parentheses, which shall be ignored. Phone numbers can also include one or more ASCII comma characters(hex 2C) to indicate a two-second pause during the dialing sequence. If either the phone,fax, or email information is not available, then a line should not included for this information. NOTE: For interoperability purposes, it is advisable to use email addresses formatted according to RFC 822 requirements. Refer to Standard Printer MIB for more details. Additional information: Replaces PML SYSTEM-CONTACT. The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user entered string is too long, the device will store as much as possible and will return the status.
INT prtgeneralstartuppage	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.14	INTEGER	read-only	Used to enable or disable printing a startup page. If enabled, a startup page will be printed shortly after power-up, when the device is ready. Typical startup pages include test patterns and/or printer configuration information. Refer to Standard Printer MIB for more details.
prtGeneralTable	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1
prtInput	1.3.6.1.4.1.11.2.3.9.4.2.2.8
INT prtinputcapacityunit	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.8	INTEGER	read-only	The unit of measurement for use in calculating and relaying capacity values for this input sub-unit. Refer to Standard Printer MIB for more details. Additional information: A sheet is a single piece of 20 pound paper. For tray 4, the envelope feeder, a sheet is one envelope
INT prtinputcurrentlevel	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.10	INTEGER	read-only	The current capacity of the input sub-unit in input sub-unit capacity units (PrtCapacityUnitTC). If this input sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests; otherwise, the value may be written (by a Remote Contol Panel or a Management Application). The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. The value (-2) means unknown. The value (-3) means that the printer knows that at least one unit remains. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series can only detect empty/not empty for its trays. It returns -3 for not empty and 0 for empty. If a tray is removed, a value of -2 (unknown) will be returned.
INT prtinputdefaultindex	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.6	INTEGER	read-only	The value of prtInputIndex corresponding to the default input sub-unit: that is, this object selects the default source of input media. This value shall be -1 if there is no default input subunit specified for the printer as a whole. In this case, the actual default input subunit may be specified by means outside the scope of this MIB, such as by each interpreter in a printer with multiple interpreters. Refer to Standard Printer MIB for more details. Additional information: The default input tray is determined by the printer based on DEFAULT-MEDIA-SIZE and DEFAULT-MEDIA-NAME, and whether or not optional trays are installed. If Tray 1 is set in FIRST mode then the size of paper loaded in Tray 1 is assumed to be the requested size. In this case, the printer will pick from Tray 1 without regard to the requested size unless the print job's paper size, paper type and tray designations exactly match the configuration of another tray; in that case, the requested tray will be picked.
OCT prtinputdescription	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.18	OCTET STRING	read-only	A free-form text description of this input sub-unit in the localization specified by prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details.
INT prtinputdimunit	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.3	INTEGER	read-only	The unit of measurement for use calculating and relaying dimensional values for this input sub-unit. Refer to Standard Printer MIB for more details. Additional information: Following is a table of paper sizes and dimensions for each paper size supported by LaserJet 4000 Series: Size Inches (ten-thousandths) Millimeters --------------- ------------------------ ----------- eUSExecutive 72500 x 105000 184150 x 266700 eUSLetter 85000 x 110000 215900 x 279400 eUSLegal 85000 x 140000 215900 x 355600 eISOandJISA5 58286 x 82677 148000 x 210000 eISOandJISA4 82677 x 116929 210000 x 297000 eJISB5 71654 x 101181 182000 x 257000 eMonarch 38750 x 75000 98425 x 190500 eCommercial10 41250 x 95000 104775 x 241300 eInternationalDL 43307 x 86614 110000 x 220000 eInternationalC5 63780 x 90157 162000 x 229000 eInternationalB5 69291 x 98425 176000 x 250000 eCustom 85000 x 140000 (max) 215900 x 355600 (max)
prtInputEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1
INT prtinputmaxcapacity	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.9	INTEGER	read-only	The maximum capacity of the input sub-unit in input sub-unit capacity units (PrtCapacityUnitTC). There is no convention associated with the media itself so this value reflects claimed capacity. If this input sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests; otherwise, the value may be written (by a Remote Control Panel or a Management Application). The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. The value (-2) means unknown. Refer to Standard Printer MIB for more details. Additional information: Replaces PML TRAYn-MAXIMUM-CAPACITY. This is specified assuming 20 pound paper for the paper trays.
INT prtinputmediadimfeeddirchosen	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.6	INTEGER	read-only	The printer will act as if media of the chosen dimension (in the feed direction) is present in this input source. Note that this value will be used even if the input tray is empty. Feed dimension measurements are taken relative to the feed direction associated with that sub-unit and are in input sub-unit dimensional units (MediaUnit). If the printer supports the declared dimension, the granted dimension is the same as the declared dimension. If not, the granted dimension is set to the closest dimension that the printer supports when the declared dimension is set. The value (-1) means other and specifically indicates that this sub-unit places no restriction on this parameter. The value (-2) indicates unknown. Refer to Standard Printer MIB for more details. Additional information: The objects for trays 2, 3, and 5 reflect the configuration of the corresponding trays. When the tray is removed, a value of -2 is returned. The default values assume the trays are configured for letter size paper (or COM10, in the case of the envelope feeder). For tray 1 and the envelope feeder, the object returns the value of the media size for which the tray is currently configured because those trays cannot sense what size media they contain.
INT prtinputmediadimfeeddirdeclared	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.4	INTEGER	read-write	This object provides the value of the declared dimension, in the feed direction, of the media that is (or, if empty, was or will be) in this input sub-unit. The feed direction is the direction in which the media is fed on this sub-unit. This dimension is measured in input sub-unit dimensional units (prtInputDimUnit). If this input sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests. Otherwise, the value may be changed. The value (-1) means other and specifically means that this sub-unit places no restriction on this parameter. The value (-2) indicates unknown. Refer to Standard Printer MIB for more details. Additional information: For trays 2, 3, and 5 (which can reliably sense this value) these objects behave exactly the same as prtInputMediaDimFeedDirChosen. Attempting to set the objects for tray 2, 3, or 5 will cause to be returned. The default values assume the trays are configured for letter size paper (or COM10, in the case of the envelope feeder). For tray 1, the value is the dimension for the media size currently declared. For the envelope feeder (tray 4), the value is the dimension for the media size currently declared. Valid values are 0 to 268435455. If a value within 0.2 inches of a standard size (e.g. 85001) is chosen when setting these objects, the standard size will be set for the specified tray if the value of prtInputMediaDimXFeedDirDeclared is also set to within 0.2 inches of the same standard size. If the value is not within 0.2 inches, Custom will be chosen as the size if it is supported by the specified tray, otherwise the first available standard size for the tray will be selected.
INT prtinputmediadimxfeeddirchosen	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.7	INTEGER	read-only	The printer will act as if media of the chosen dimension (in the cross feed direction) is present in this input source. Note that this value will be used even if the input tray is empty. The cross feed direction is ninety degrees relative to the feed direction associated with this sub-unit. This dimension is measured in input sub-unit dimensional units (MediaUnit). If the printer supports the declared dimension, the granted dimension is the same as the declared dimension. If not, the granted dimension is set to the closest dimension that the printer supports when the declared dimension is set. The value (-1) means other and specifically indicates that this sub-unit places no restriction on this parameter. The value (-2) indicates unknown. Refer to Standard Printer MIB for more details. Additional information: The objects for trays 2, 3, and 5 reflect the configuration of the corresponding trays. When the tray is removed, a value of -2 is returned. The default values assume the trays are configured for letter size paper (or COM10, in the case of the envelope feeder). The objects for tray 1 and the envelope feeder return the value of the media size for which the tray is currently configured because those trays cannot sense what size media they contain.
INT prtinputmediadimxfeeddirdeclared	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.5	INTEGER	read-write	This object provides the value of the declared dimension, in the cross feed direction, of the media that is (or, if empty, was or will be) in this input sub-unit. The cross feed direction is ninety degrees relative to the feed direction associated with this sub-unit. This dimension is measured in input sub-unit dimensional units (prtInputDimUnit). If this input sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests. Otherwise, the value may be changed. The value (-1) means other and specifically means that this sub-unit places no restriction on this parameter. The value (-2) indicates unknown. Refer to Standard Printer MIB for more details. Additional information: For trays 2, 3, and 5 (which can reliably sense this value) these objects behave exactly the same as prtInputMediaDimXFeedDirChosen. Attempting to set these objects for tray 2, 3, and 5 will cause to be returned. The default values assume the trays are configured for letter size paper (or COM10, in the case of the envelope feeder). For tray 1 the value is the dimension for the media size currently declared. Valid values are 0 to 268435455. If a value within 0.2 inches of a standard size (e.g. 85001) is chosen when setting these objects, the standard size will be set for the specified tray if the value of prtInputMediaDimFeedDirDeclared is also set to within 0.2 inches of the same standard size. If the value is not within 0.2 inches, Custom will be chosen as the size if it is supported by the specified tray, otherwise the first available standard size for the tray will be selected.
INT prtinputmedialoadtimeout	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.24	INTEGER	read-only	When the printer is not able to print due to a subunit being empty or the requested media must be manually loaded, the printer will wait for the duration (in seconds) specified by this object. Upon expiration of the timeout, the printer will take the action specified by prtInputNextIndex. The event which causes the printer to enter the waiting state is product specific. If the printer is not waiting for manually fed media, it may switch from an empty subunit to a different subunit without waiting for the timeout to expire. A value of (-1) implies 'other' or 'infinite' which translates to 'wait forever'. The action which causes printing to continue is product specific. A value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: This object simply reflects the value of the JOB-INPUT-AUTO-CONTINUE-TIMEOUT object. See the description of that object for additional information.
OCT prtinputmedianame	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.12	OCTET STRING	read-write	A description of the media contained in this input sub-unit; This description is intended for display to a human operator. This description is not processed by the printer. It is used to provide information not expressible in terms of the other media attributes (e.g. prtInputMediaDimFeedDirChosen, prtInputMediaDimXFeedDirChosen, prtInputMediaWeight, prtInputMediaType). An example would be `legal tender bond paper'. Refer to Standard Printer MIB for more details. Additional information: Replaces PML TRAYn-MEDIA-NAME. If set to a string other than one contained by a MEDIAn-NAME object, a status of is returned. If set to a string that is unsupported for the specified tray object, a status of is returned. After Build5.0 (LaserJet 8100 Series) Cassette trays will not support Transparency nor Label media types. The value of this object is saved across a power cycle.
OCT prtinputmodel	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.15	OCTET STRING	read-only	The model name of this input sub-unit. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series does not specify a model name for Tray1 or Tray2, nor for Tray 3 in the 2x250 tray configuration. However, if Tray 3 is installed in the 1x500 configuration, 'Optional Cassette C4124A' will be returned. Tray 3, 4, and 5 objects do not exist unless those trays are installed.
OCT prtinputname	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.13	OCTET STRING	read-only	The name assigned to this input sub-unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML TRAYn-NAME.
INT prtinputnextindex	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.26	INTEGER	read-only	The value of prtInputIndex corresponding to the input subunit which will be used when this input subunit is emptied and the timeout specified by prtInputMediaLoadTimeout expires. A value of zero(0) indicates that auto input switching will not occur when this input subunit is emptied. If the timeout specified by prtInputLoadMediaTimeout expires and this value is zero(0), the job will be aborted. A value of (-1) means other. The value (-2) means 'unknown' and specifically indicates that an implementation specific method will determine the next input subunit to use at the time this subunit is emptied and the timeout expires. The value(-3) means input switching is not supported for this subunit. Refer to Standard Printer MIB for more details. Additional information: This object reflects the state of JOB-INPUT-AUTO-CONTINUE-MODE and JOB-INPUT-AUTO-CONTINUE-TIMEOUT. If JOB-INPUT-AUTO-CONTINUE-TIMEOUT is set to -1 or JOB-INPUT-AUTO-CONTINUE-MODE is set up to cancel the job, this object will return 0. If JOB-INPUT-AUTO-CONTINUE-TIMEOUT is >= 0 and JOB-INPUT-AUTO-CONTINUE-MODE is not set up to cancel the job, this object will return -2, meaning that a product-specific tray switching action will occur.
INT prtinputsecurity	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.19	INTEGER	read-only	Indicates if this input sub-unit has some security associated with it. Refer to Standard Printer MIB for more details. Additional information: No security mechanism provided.
OCT prtinputserialnumber	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.17	OCTET STRING	read-only	The serial number assigned to this input sub-unit. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series does not specify a serial number for the input trays.
INT prtinputstatus	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.11	INTEGER	read-only	The current status of this input sub-unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML STATUS-TRAY-MISSING and STATUS-TRAY-EMPTY. Values returned by the firmware are detailed in the following table. 'Value Or'd Due To Condition' indicates that the specified value will be logically or'd into the value for this object when the specified Condition occurs. Condition Value Or'd Due To Condition ----------------------- ------------------------ Tray Lifter Error 3 Tray not installed or not inserted or not occupied 1 Tray is current source tray and paper is moving 6 Tray involved in paper mount 16 + 32 Value 3 or 1 is Or'd in 8 Tray is lifting 64
prtInputTable	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2
INT prtinputtype	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.2	INTEGER	read-only	The type of technology (discriminated primarily according to feeder mechanism type) employed by the input sub-unit. Note, the Optional Input Class provides for a descriptor field to further qualify the other choice. Refer to Standard Printer MIB for more details. Additional information: Tray 1 is the multi-purpose tray and is always present. It supports both sheets and envelopes. Its type is ePsheetFeedAutoNonRemovableTray. Tray 2 is a removable tray that comes standard with the printer, although it is usually not removed from the printer. It is of type ePsheetFeedAutoRemovableTray. Tray 3 is either a 250-sheet standard tray in the 2x250 base engine configuration or a 500-sheet optional tray in the 1x500 base engine configuration. (The optional tray is only recognized if it's installed before the printer is powered on.) It is of type ePsheetFeedAutoRemovableTray. The 4th tray in this array is the envelope feeder. It can be detected even when it is installed while the printer is powered on. Tray 5 is a 500-sheet optional tray that cannot be installed while the printer is powered on. It is of type ePsheetFeedAutoRemovableTray.
OCT prtinputvendorname	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.14	OCTET STRING	read-only	The vendor name of this input sub-unit. Refer to Standard Printer MIB for more details.
OCT prtinputversion	1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.16	OCTET STRING	read-only	The version of this input sub-unit. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series does not specify a version number for the input trays.
prtInterpreter	1.3.6.1.4.1.11.2.3.9.4.2.2.15
INT prtinterpreterdefaultcharsetin	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.10	INTEGER	read-write	The default coded character set for input octets encountered outside a context in which the Page Description Language established the interpretation of the octets. (Input octets are presented to the interpreter through a path defined in the channel group.) This value shall be (2) if there is no default. Refer to Standard Printer MIB for more details. Additional information: The object corresponding to PCL has read-write access; For all other interpreters, the object is read-only. The above list corresponds to the following symbol sets as they appear on the Control Panel: ePcsASCII( 3) - ISO-6 ePcsISOLatin1( 4) - ISO L1 ePcsISOLatin2( 5) - IS L2 ePcsISOLatin5( 12) - ISO L5 ePcsISOLatin6( 13) - ISO L6 ePcsISO4UnitedKingdom( 20) - ISO-4 ePcsISO11SwedishforNames( 21) - ISO-11 ePcsISO15Italian( 22) - ISO-15 ePcsISO17Spanish( 23) - ISO-17 ePcsISO21German( 24) - ISO-21 ePcsISO60DanishNorwegian( 25) - ISO-60 ePcsISO69French( 26) - ISO-69 ePcsUnicodeIBM2039(1004) - PC-1004 ePcsWindows30Latin1( 2000) - WIN 3.0 ePcsWindows31Latin1( 2001) - WIN L1 ePcsWindows31Latin2( 2002) - WIN L2 ePcsWindows31Latin5( 2003) - WIN L5 ePcsHPRoman8( 2004) - ROMAN-8 ePcsAdobeStandardEncoding( 2005) - PS TEXT ePcsPC850Multilingual( 2009) - PC-850 ePcsPCp852( 2010) - PC-852 ePcsPC8CodePage437( 2011) - PC-8 ePcsPC8DNDanishNorwegian( 2012) - PC-8DN ePcsHPPC8Turkish( 2014) - PC-8 TK ePcsHPLegal( 2017) - LEGAL ePcsHPDeskTop( 2021) - DESKTOP ePcsMacintosh(2027) - MC TEXT ePcsPC775Baltic( 2087) - PC-775 ePcsWindows1257Baltic( 2257) - WINBALT
INT prtinterpreterdefaultcharsetout	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.11	INTEGER	read-only	The default character set for data coming from this interpreter through the printer's output channel (i.e. the 'backchannel'). This value shall be (2) if there is no default. Refer to Standard Printer MIB for more details.
INT prtinterpreterdefaultorientation	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.7	INTEGER	read-write	The current orientation default for this interpreter. This value may be overridden for a particular job (e.g., by a command in the input data stream). Refer to Standard Printer MIB for more details. Additional information: The value of the system's DEFAULT-ORIENTATION is set or retrieved without regard to interpreters. Setting this object for one interpreter will change it for all installed interpreters. The valid values are ePportrait and ePlandscape. Attempting to set the orientation to a different value will cause to be returned.
OCT prtinterpreterdescription	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.5	OCTET STRING	read-only	A string to identify this interpreter in the localization specified by prtGeneralCurrentLocalization as opposed to the language which is being interpreted. It is anticipated that this string will allow manufacturers to unambiguously identify their interpreters. Refer to Standard Printer MIB for more details. Additional information: These values are obtained from the persName fields of the personality entities (except for the hard-coded value of 'Automatic Language Switching'.) These strings are not localized.
prtInterpreterEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1
INT prtinterpreterfeedaddressability	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.8	INTEGER	read-only	The maximum interpreter addressability in the feed direction in 10000 prtMarkerAddressabilityUnits (see prtMarkerAddressabilityFeedDir ) for this interpreter. The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. Refer to Standard Printer MIB for more details.
INT prtinterpreterlangfamily	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.2	INTEGER	read-only	The family name of a Page Description Language (PDL) or control language which this interpreter in the printer can interpret or emulate. Refer to Standard Printer MIB for more details. Additional information: ePlangAutomatic refers to the `super-language' made available by implicit language switching.
OCT prtinterpreterlanglevel	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.3	OCTET STRING	read-only	The level of the language which this interpreter is interpreting or emulating. This might contain a value like '5e' for an interpreter which is emulating level 5e of the PCL language. It might contain '2' for an interpreter which is emulating level 2 of the PostScript language. Similarly it might contain '2' for an interpreter which is emulating level 2 of the HPGL language. Refer to Standard Printer MIB for more details. Additional information: Replaces PML PCL-VERSION.
OCT prtinterpreterlangversion	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.4	OCTET STRING	read-only	The date code or version of the language which this interpreter is interpreting or emulating. Refer to Standard Printer MIB for more details. Additional information: Replaces PML FW-ROM-DATECODE, PJL-DATECODE, PCL-DATECODE and PS-DATECODE These values are derived from the dateCode field of the personality entities. (ePlangAutomatic uses the PJL dateCode.)
prtInterpreterTable	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1
INT prtinterpretertwoway	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.12	INTEGER	read-only	Indicates whether or not this interpreter returns information back to the host. Refer to Standard Printer MIB for more details.
OCT prtinterpreterversion	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.6	OCTET STRING	read-only	The date code, version number, or other product specific information tied to this interpreter. This value is associated with the interpreter, rather than with the version of the language which is being interpreted or emulated. Refer to Standard Printer MIB for more details. Additional information: Same as prtInterpreterLangVersion.
INT prtinterpreterxfeedaddressability	1.3.6.1.4.1.11.2.3.9.4.2.2.15.1.1.9	INTEGER	read-only	The maximum interpreter addressability in the cross feed direction in 10000 prtMarkerAddressabilityUnits (see prtMarkerAddressabilityXFeedDir) for this interpreter. The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. Refer to Standard Printer MIB for more details.
prtLocalization	1.3.6.1.4.1.11.2.3.9.4.2.2.7
INT prtlocalizationcharacterset	1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.4	INTEGER	read-only	The coded character set used for this localization. Refer to Standard Printer MIB for more details.
OCT prtlocalizationcountry	1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.3	OCTET STRING	read-only	A two character country code from ISO 3166, a blank string (two space characters) shall indicate that the country is not defined. Examples: US, FR, DE, ... Refer to Standard Printer MIB for more details. Additional information: The languages supported by LaserJet 4050 Series (and corresponding country) are English (US, United States), French (FR, France), German (DE, Germany), Italian (IT, Italy), Spanish (ES, Spain), Swedish (SE, Sweden), Danish (DK, Denmark), Norwegian (NO, Norway), Dutch (NL, Netherlands), Finnish (FI, Finland), Portuguese (PT, Portugal), Turkish (TR, Turkey), Polish (PL, Poland), Japanese (JP, Japan), Russian, (RU, Russia), Czech (CS, Czechoslovakia), Hungarian (HU, Hungary)
prtLocalizationEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1
OCT prtlocalizationlanguage	1.3.6.1.4.1.11.2.3.9.4.2.2.7.1.1.2	OCTET STRING	read-only	A two character language code from ISO 639. Examples en, gb, ca, fr, de. Refer to Standard Printer MIB for more details. Additional information: The languages supported by LaserJet 4050 Series are English, French, German, Italian, Spanish, Swedish, Danish, Norwegian, Dutch, Finnish, Portuguese, Turkish, Polish, Japanese, Russian, Czech, and Hungarian.
prtLocalizationTable	1.3.6.1.4.1.11.2.3.9.4.2.2.7.1
prtMarker	1.3.6.1.4.1.11.2.3.9.4.2.2.10
INT prtmarkeraddressabilityfeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.9	INTEGER	read-only	The maximum number of addressable marking positions in the feed direction per 10000 units of measure specified by prtMarkerAddressabilityUnit. A value of (-1) implies 'other' or 'infinite' while a value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: This object indicates the value of the resolution (dots per inch) setting for the printer. LaserJet 5000 Series and LaserJet 4000 Series support 300, 600 and 1200 dots per inch. LaserJet 8100 Series and LaserJet 8000 Series supports 300 or 600 dots per inch. 600 dots per inch is the default.
INT prtmarkeraddressabilityunit	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.8	INTEGER	read-only	The unit of measure of distances, as applied to the marker's resolution. Refer to Standard Printer MIB for more details. Additional information: This will always be ePtenThousandthsOfInches, no matter what COLD-RESET-MEDIA-SIZE is because we are talking about resolution and toner addressability, which is always dpi.
INT prtmarkeraddressabilityxfeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.10	INTEGER	read-only	The maximum number of addressable marking positions in the cross feed direction in 10000 units of measure specified by prtMarkerAddressabilityUnit. A value of (-1) implies 'other' or 'infinite' while a value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: This object indicates the value of the resolution (dots per inch) setting for the printer. LaserJet 5000 Series and LaserJet 4000 Series support 300, 600 and 1200 dots per inch. LaserJet 8100 Series and LaserJet 8000 Series supports 300 or 600 dots per inch. 600 dots per inch is the default.
INT prtmarkercounterunit	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.3	INTEGER	read-only	The unit that will be used by the printer when reporting counter values for this marking sub-unit. The time units of measure are provided for a device like a strip recorder that does not or cannot track the physical dimensions of the media and does not use characters, lines or sheets. Refer to Standard Printer MIB for more details. Additional information: Since LaserJet 4050 Series keeps track of pages printed, the counter unit will be defined as ePimpressions which would be like saying pages printed.
INT prtmarkerdefaultindex	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.8	INTEGER	read-only	The value of prtMarkerIndex corresponding to the default marker sub-unit; that is, this object selects the default marker. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4050 Series only has one marker subunit.
INT prtmarkereastmargin	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.14	INTEGER	read-only	The margin from the East edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by all four margins is guaranteed for all interpreters. The value (-2) means unknown. Refer to Standard Printer MIB for more details.
prtMarkerEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1
INT prtmarkerlifecount	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.4	INTEGER	read-only	The count of the number of units of measure counted during the life of printer using units of measure as specified by prtMarkerCounterUnit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML TOTAL-ENGINE-PAGE-COUNT. The total engine page count is kept in NVRAM however the NVRAM value is only updated every 10 impressions. NOTE: The value returned by this OID will be incremented every page but if power is lost between NVRAM updates, up to 9 impressions of the page count may be lost. The counter will be reset to zero after 999999 pages. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by two.
INT prtmarkermarktech	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.2	INTEGER	read-only	The type of marking technology used for this marking sub-unit. Refer to Standard Printer MIB for more details. Additional information: ePelectrophotographicLaser is the only value that applies for the LaserJet 4050 Series products, and this is the value that will always be returned for this object.
INT prtmarkernorthmargin	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.11	INTEGER	read-only	The margin, in units identified by prtMarkerAddressabilityUnit, from the leading edge of the medium as the medium flows through the marking engine with the side to be imaged facing the observer. The leading edge is the North edge and the other edges are defined by the normal compass layout of directions with the compass facing the observer. Printing within the area bounded by all four margins is guaranteed for all interpreters. The value (-2) means unknown. Refer to Standard Printer MIB for more details.
INT prtmarkerpoweroncount	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.5	INTEGER	read-only	The count of the number of units of measure counted since the equipment was most recently powered on using units of measure as specified by prtMarkerCounterUnit. Refer to Standard Printer MIB for more details.
INT prtmarkerprocesscolorants	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.6	INTEGER	read-only	The number of process colors supported by this marker. A process color of 1 implies monochrome. The value of this object and prtMarkerSpotColorants cannot both be 0. The value of prtMarkerProcessColorants must be 0 or greater. Refer to Standard Printer MIB for more details.
INT prtmarkersouthmargin	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.12	INTEGER	read-only	The margin from the South edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by all four margins is guaranteed for all interpreters. The value (-2) means unknown. Refer to Standard Printer MIB for more details.
INT prtmarkerspotcolorants	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.7	INTEGER	read-only	The number of spot colors supported by this marker. The value of this object and prtMarkerProcessColorants cannot both be 0. Must be 0 or greater. Refer to Standard Printer MIB for more details.
INT prtmarkerstatus	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.15	INTEGER	read-only	The current status of this marker sub-unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML NOT-READY-DESTINATION-PRINT-ENGINE and STATUS-DESTINATION-PRINT-ENGINE. 51 = No toner cart. 49 = Low toner and toner low = stop in config menu 14 = Low toner and toner low = continue in config menu and paper is moving. 08 = Low toner and toner low = continue in config menu and no paper is moving. 00 = OK. The default value assumes no malfunctions.
prtMarkerSupplies	1.3.6.1.4.1.11.2.3.9.4.2.2.11
INT prtmarkersuppliesclass	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.4	INTEGER	read-only	Indicates whether this supply entity represents a supply that is consumed or a receptacle that is filled. Refer to Standard Printer MIB for more details. Additional information: ePsupplyThatIsConsumed is the only value that applies for the LaserJet 4050 Series products, and this is the value that will always be returned for this object.
INT prtmarkersuppliescolorantindex	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.3	INTEGER	read-only	The value of prtMarkerColorantIndex corresponding to the colorant with which this marker supply sub-unit is associated. This value shall be 0 if there is no colorant table. Refer to Standard Printer MIB for more details.
OCT prtmarkersuppliesdescription	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.6	OCTET STRING	read-only	The description of this supply container/receptacle in the localization specified by prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details.
prtMarkerSuppliesEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1
INT prtmarkersupplieslevel	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.9	INTEGER	read-only	The current level if this supply is a container; the remaining space if this supply is a receptacle. If this supply container/receptacle can reliably sense this value, the value is reported by the printer and is read-only; otherwise, the value may be written (by a Remote Control Panel or a Management Application). The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. The value (-2) means unknown. A value of (-3) means that the printer knows that there is some supply/remaining space, respectively. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4050 Series will have a new toner-measuring feature that utilizes the GRIN ASIC's ability to detect the amount of pixels that have been placed on a single page. This Pixel-Counting Gas Gauge should be able to calculate toner levels within 10%. Because textual printing and graphics printing utilize different pixel usage, accuracy for the counting algorithms have been biased toward textual printing. Heavy graphics printing will cause the cartridge to appear to be emptier than it really is. Over time however, statistical averaging values that are kept in NVRAM will help make the gauge more accurate according to individual customer usage models. The new values will vary between 0 and 4600 depending on how much toner has been calculated to have been used.
INT prtmarkersuppliesmarkerindex	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.2	INTEGER	read-only	The value of prtMarkerIndex corresponding to the marking sub-unit with which this marker supply sub-unit is associated. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4050 Series has just one marker supply, the toner cartridge, so this value is always 1.
INT prtmarkersuppliesmaxcapacity	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.8	INTEGER	read-only	The maximum capacity of this supply container/receptacle expressed in prtMarkerSuppliesSupplyUnit. If this supply container/receptacle can reliably sense this value, the value is reported by the printer and is read-only; otherwise, the value may be written (by a Remote Control Panel or a Management Application). The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. The value (-2) means unknown. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4050 Series - LaserJet 4050 Series now has the same toner-mesuring feature as LaserJet 8100 Series which utilizes the GRIN ASICS's ability to detect the number of pixels placed on a page. The default value units are in 10ths of a gram. A 27X toner cartridge holds 460 grams of toner. Note :a 27A cartidge holds 303 g but we are using the 27X value.
INT prtmarkersuppliessupplyunit	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.7	INTEGER	read-only	Unit of measure of this marker supply container/receptacle. Refer to Standard Printer MIB for more details. Additional information: ePtenthsOfGrams will always be returned for this object.
prtMarkerSuppliesTable	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1
INT prtmarkersuppliestype	1.3.6.1.4.1.11.2.3.9.4.2.2.11.1.1.5	INTEGER	read-only	The type of this supply. Refer to Standard Printer MIB for more details. Additional information: ePtoner is the only value that applies for the LaserJet 4050 Series products, and this is the value that will always be returned for this object.
prtMarkerTable	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2
INT prtmarkerwestmargin	1.3.6.1.4.1.11.2.3.9.4.2.2.10.2.1.13	INTEGER	read-only	The margin from the West edge (see prtMarkerNorthMargin) of the medium in units identified by prtMarkerAddressabilityUnit. Printing within the area bounded by all four margins is guaranteed for all interpreters. The value (-2) means unknown. Refer to Standard Printer MIB for more details.
prtMediaPath	1.3.6.1.4.1.11.2.3.9.4.2.2.13
INT prtmediapathdefaultindex	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.9	INTEGER	read-write	The value of prtMediaPathIndex corresponding to the default media path; that is, the selection of the default media path. Refer to Standard Printer MIB for more details. Additional information: If the duplex unit is not installed, the only valid value for this object is 1; with duplex unit installed, 1-3 values are valid. 1 is simplex, 2 is LongEdgeBindingDuplex, and 3 is ShortEdgeBindingDuplex. If the printer is not idle, the new value of this object may not take effect until a job boundary is reached. If a get is done on this object before the job boundary is reached, the value last set will be returned.
OCT prtmediapathdescription	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.10	OCTET STRING	read-only	The manufacturer-provided description of this media path in the localization specified by prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details.
prtMediaPathEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1
INT prtmediapathmaxmediafeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.5	INTEGER	read-only	The maximum physical media size in the feed direction of this media path expressed in units of measure specified by PrtMediaPathMediaSizeUnit. A value of (-1) implies 'unlimited', a value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: The value returned by this object depends on the value of prtMediaPathMediaSizeUnit. It is 140000 if prtMediaPathMediaSizeUnit is ePtenThousandthsOfInches or 355600 if prtMediaPathMediaSizeUnit is ePmicrometers.
INT prtmediapathmaxmediaxfeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.6	INTEGER	read-only	The maximum physical media size across the feed direction of this media path expressed in units of measure specified by prtMediaPathMediaSizeUnit. A value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: The value returned by this object depends on the value of prtMediaPathMediaSizeUnit. It is 85000 if prtMediaPathMediaSizeUnit is ePtenThousandthsOfInches and 215900 if prtMediaPathMediaSizeUnit is ePmicrometers.
INT prtmediapathmaxspeed	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.4	INTEGER	read-only	The maximum printing speed of this media path expressed in prtMediaPathMaxSpeedUnit's. A value of (-1) implies 'other'. Refer to Standard Printer MIB for more details. Additional information: Replaces PML PRINT-ENGINE-PERFORMANCE. The page size for this performance is 8.5x11. The duplex speed is based on 6 ppm.
INT prtmediapathmaxspeedprintunit	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.2	INTEGER	read-only	The unit of measure used in specifying the speed of all media paths in the printer. Refer to Standard Printer MIB for more details. Additional information: ePimpressionsPerHour is the value that will always be returned for this object. (Print Speed is measured in pages-per-minute (impressions per minute), so ePimpressionsPerHour is a natural extension).
INT prtmediapathmediasizeunit	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.3	INTEGER	read-only	The units of measure of media size for use in calculating and relaying dimensional values for all media paths in the printer. Refer to Standard Printer MIB for more details.
INT prtmediapathminmediafeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.7	INTEGER	read-only	The minimum physical media size in the feed direction of this media path expressed in units of measure specified by prtMediaPathMediaSizeUnit. A value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: The value returned by this object depends on the value of prtMediaPathMediaSizeUnit. It is 50000 if prtMediaPathMediaSizeUnit is ePtenThousandthsOfInches or 127000 if prtMediaPathMediaSizeUnit is ePmicrometers.
INT prtmediapathminmediaxfeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.8	INTEGER	read-only	The minimum physical media size across the feed direction of this media path expressed in units of measure specified by prtMediaPathMediaSizeUnit. A value of (-2) implies 'unknown'. Refer to Standard Printer MIB for more details. Additional information: The value returned by this object depends on the value of prtMediaPathMediaSizeUnit. It is 30000 if prtMediaPathMediaSizeUnit is ePtenThousandthsOfInches or 76200 if prtMediaPathMediaSizeUnit is ePmicrometers.
INT prtmediapathstatus	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.11	INTEGER	read-only	The current status of this media path. Refer to Standard Printer MIB for more details. Additional information: The default values assume the printer is idle.
prtMediaPathTable	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4
INT prtmediapathtype	1.3.6.1.4.1.11.2.3.9.4.2.2.13.4.1.9	INTEGER	read-only	The type of the media path for this media path. Refer to Standard Printer MIB for more details. Additional information: Replaces PML DUPLEX-INSTALLED.
prtOutput	1.3.6.1.4.1.11.2.3.9.4.2.2.9
INT prtoutputbursting	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.21	INTEGER	read-only	This object indicates that the outputting sub-unit supports bursting, and if so, whether the feature is enabled. Bursting is the process by which continuous media is separated into individual sheets, typically by bursting along pre-formed perforations. Refer to Standard Printer MIB for more details.
INT prtoutputcapacityunit	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.3	INTEGER	read-only	The unit of measurement for use in calculating and relaying capacity values for this output sub-unit. Refer to Standard Printer MIB for more details. Additional information: A sheet is a single piece of 20 pound paper.
INT prtoutputdecollating	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.22	INTEGER	read-only	This object indicates that the output supports supports decollating, and if so, whether the feature is enabled. Decollating is the process by which the individual parts within a multi-part form are separated and sorted into separate stacks for each part. Refer to Standard Printer MIB for more details.
INT prtoutputdefaultindex	1.3.6.1.4.1.11.2.3.9.4.2.2.5.1.1.7	INTEGER	read-write	The value of prtOutputIndex corresponding to the default output sub-unit; that is, this object selects the default output destination. This value shall be -1 if there is no default output subunit specified for the printer as a whole. In this case, the actual default output subunit may be specified by means outside the scope of this MIB, such as by each interpreter in a printer with multiple interpreters. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4050 Series (LaserJet 4050) has two output bins in the base product: a face-up bin on the back of the engine and a face-down bin on the top of the engine. These bins are not firmware-selectable; instead, paper is diverted to the face-down bin only if the face-up bin is physically closed. Therefore, these bins are considered together as the 'standard' bin. However, if an HCO is attached to the engine, users will be able to select between an HCO bin and the 'standard' bin, which may be either the face-up or face-down bin, depending upon whether the face-up bin is open. With external output bins attached, the value of this object will be settable from the control panel and by the PJL OUTBIN variable.
OCT prtoutputdescription	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.12	OCTET STRING	read-only	A free-form text description of this output sub-unit in the localization specified by prtGeneralCurrentLocalization. Refer to Standard Printer MIB for more details.
INT prtoutputdimunit	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.14	INTEGER	read-only	The unit of measurement for use in calculating and relaying dimensional values for this output sub-unit. Refer to Standard Printer MIB for more details. Additional information: See the description for prtInputDimUnit for a table of supported paper sizes and their dimensions for LaserJet 4000 Series.
prtOutputEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1
INT prtoutputmaxcapacity	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.4	INTEGER	read-only	The maximum capacity of this output sub-unit in output sub-unit capacity units (PrtCapacityUnitTC). There is no convention associated with the media itself so this value essentially reflects claimed capacity. If this output sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests; otherwise, the value may be written (by a Remote Control Panel or a Management Application). The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. The value (-2) means unknown. Refer to Standard Printer MIB for more details. Additional information: Replaces PML OUTBINn-MAXIMUM-CAPACITY. LaserJet 4000 Series cannot sense the amount of paper in its standard output bin; however, the face-up bin can hold 50 sheets of 20lb. paper, and the face-down bin can hold 250 sheets. External output devices are currently T.B.D.
INT prtoutputmaxdimfeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15	INTEGER	read-only	The maximum dimensions supported by this output sub-unit for measurements taken parallel relative to the feed direction associated with that sub-unit in output sub-unit dimensional units (MediaUnit). If this output sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed with management protocol operations. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series has two output bins in the base product: a face-up bin on the back of the engine and a face-down bin on the top of the engine. These bins are not firmware-selectable; instead, paper is diverted to the face-down bin only if the face-up bin is physically closed. Therefore, these bins are considered together as the 'standard' bin. The value returned by this object depends on the value of prtOutputDimUnit. It is 140000 if prtOutputDimUnit is ePtenThousandthsOfInches or 355600 if prtOutputDimUnit is ePmicrometers.
INT prtoutputmaxdimxfeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.16	INTEGER	read-only	The maximum dimensions supported by this output sub-unit for measurements taken ninety degrees relative to the feed direction associated with that sub-unit in output sub-unit dimensional units (MediaUnit). If this output sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed with management protocol operations. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series has two output bins in the base product: a face-up bin on the back of the engine and a face-down bin on the top of the engine. These bins are not firmware-selectable; instead, paper is diverted to the face-down bin only if the face-up bin is physically closed. Therefore, these bins are considered together as the 'standard' bin. The value returned by this object depends on the value of prtOutputDimUnit. It is 85000 if prtOutputDimUnit is ePtenThousandthsOfInches and 215900 if prtOutputDimUnit is ePmicrometers.
INT prtoutputmindimfeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.17	INTEGER	read-only	The minimum dimensions supported by this output sub-unit for measurements taken parallel relative to the feed direction associated with that sub-unit in output sub-unit dimensional units (DimUnit). If this output sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed with management protocol operations. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series has two output bins in the base product: a face-up bin on the back of the engine and a face-down bin on the top of the engine. These bins are not firmware-selectable; instead, paper is diverted to the face-down bin only if the face-up bin is physically closed. Therefore, these bins are considered together as the 'standard' bin. The value returned by this object depends on the value of prtOutputDimUnit. It is 50000 if prtOutputDimUnit is ePtenThousandthsOfInches or 127000 if prtOutputDimUnit is ePmicrometers.
INT prtoutputmindimxfeeddir	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.18	INTEGER	read-only	The minimum dimensions supported by this output sub-unit for measurements taken ninety degrees relative to the feed direction associated with that sub-unit in output sub-unit dimensional units (DimUnit). If this output sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed with management protocol operations. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series has two output bins in the base product: a face-up bin on the back of the engine and a face-down bin on the top of the engine. These bins are not firmware-selectable; instead, paper is diverted to the face-down bin only if the face-up bin is physically closed. Therefore, these bins are considered together as the 'standard' bin. The value returned by this object depends on the value of prtOutputDimUnit. It is 30000 if prtOutputDimUnit is ePtenThousandthsOfInches or 76200 if prtOutputDimUnit is ePmicrometers.
OCT prtoutputmodel	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.9	OCTET STRING	read-only	The name assigned to this output sub-unit. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series does not support a model number for its built-in output bins. This object may change in the future when external output devices are added.
OCT prtoutputname	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.7	OCTET STRING	read-only	The name assigned to this output sub-unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML OUTBINn-NAME. The characters must be in the range 20H to 7FH except 5C cannot be used. When this string is displayed on the control panel the Roman-8 symbol set is used.
INT prtoutputoffsetstacking	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.24	INTEGER	read-only	This object indicates that the output supports supports offset stacking, and if so, whether the feature is enabled. See glossary for how Offset Stacking is defined by this document. Refer to Standard Printer MIB for more details.
INT prtoutputpagecollated	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.23	INTEGER	read-only	This object indicates that the output sub-unit supports page collation, and if so, whether the feature is enabled. See glossary for definition of how this document defines collation. Refer to Standard Printer MIB for more details.
INT prtoutputpagedeliveryorientation	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.20	INTEGER	read-only	The reading surface that will be `up' when pages are delivered to the associated output sub-unit. Values are faceUp and faceDown. (Note: interpretation of these values is in general context-dependent based on locale; presentation of these values to an end-user should be normalized to the expectations of the user). Refer to Standard Printer MIB for more details.
INT prtoutputremainingcapacity	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.5	INTEGER	read-only	The remaining capacity of the possible output sub-unit capacity in output sub-unit capacity units (PrtCapacityUnitTC) of this output sub-unit. If this output sub-unit can reliably sense this value, the value is sensed by the printer and may not be modified by management requests; otherwise, the value may be written (by a Remote Control Panel or a Management Application). The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. The value (-2) means unknown. The value (-3) means that the printer knows that there remains capacity for at least one unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML NOT-READY-OUTBIN-FULL and STATUS-OUTBIN-FULL. LaserJet 4000 Series is capable of determining when the face-down bin goes full, but not the level of that bin. LaserJet 4000 Series is not capable of determining whether the face-up bin is full. RemainingCapacity capabilities of the stapler/stacker, as well as unplanned HCO devices, are currently T.B.D. LaserJet 4000 Series will report a value of 0 when the face-down bin is full and -3 when the face down bin is not full.
INT prtoutputsecurity	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.13	INTEGER	read-only	Indicates if this output sub-unit has some security associated with it and if that security is enabled or not. Refer to Standard Printer MIB for more details. Additional information: No security mechanism provided.
OCT prtoutputserialnumber	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.11	OCTET STRING	read-only	The serial number assigned to this output sub-unit. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series does not support a serial number for output devices.
INT prtoutputstackingorder	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.19	INTEGER	read-only	The current state of the stacking order for the associated output sub-unit. `FirstToLast' means that as pages are output the front of the next page is placed against the back of the previous page. `LasttoFirst' means that as pages are output the back of the next page is placed against the front of the previous page. Refer to Standard Printer MIB for more details. Additional information: Replaces PML OUTBINn-STACK-ORDER.
INT prtoutputstatus	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.6	INTEGER	read-only	The current status of this output sub-unit. Refer to Standard Printer MIB for more details. Additional information: Replaces PML NOT-READY-OUTBIN-MISSING and STATUS-OUTBIN-MISING. The default values assume all bins are empty. See SubUnitStatus in RFC1759 Printer MIB for details on values reported by this object. LaserJet 4000 Series will not include values Available and Standby (2), Available and Active (4), Unknown (5) or Transitioning to Intended State (64). Values returned by the firmware are detailed in the following table. 'Value Or'd Due To Condition' indicates that the specified value will be logically or'd into the value for this object when the specified Condition occurs. Condition Value Or'd Due To Condition ----------------------- ------------------------ Binder Error 3 Bin full, binder empty, bind limit reached, binder align error, bin attention error, or bin attention warning 1 Bin is current bin and paper is moving 6 Bin is the bin responsible for Bin Full error message being displayed 16 + 32 Value 1 or 3 is Or'd in 8
prtOutputTable	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2
INT prtoutputtype	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.2	INTEGER	read-only	The type of technology supported by this output sub-unit. Refer to Standard Printer MIB for more details. Additional information: LaserJet 4000 Series has two built-in output bins: a face-down bin located at the top of the printer and a face-up bin located at the rear of the printer. However, neither of these bins is firmware-selectable, so both bins are considered together as the 'standard' bin. LaserJet 4000 Series supports HCO devices as well as a stacker/stapler, but these devices are currently T.B.D.
OCT prtoutputvendorname	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.8	OCTET STRING	read-only	The vendor name of this output sub-unit. Refer to Standard Printer MIB for more details.
OCT prtoutputversion	1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.10	OCTET STRING	read-only	The version of this output sub-unit. Refer to Standard Printer MIB for more details. Additional information: Returns device-specific information about the configuration of the output bin. May include information about the type of processing that can be done to media sent to this bin; processing includes but is not limited to binding, punching, folding and sealing. Format of this object is specified by the output device documentation.
prtStorageRefEntry	1.3.6.1.4.1.11.2.3.9.4.2.2.5.2.1
INT prtstoragerefindex	1.3.6.1.4.1.11.2.3.9.4.2.2.5.2.1.2	INTEGER	read-only	The value of the hrDeviceIndex of the printer device that this storageEntry is associated with. Refer to Standard Printer MIB for more details. Additional information (mass storage): Constant. The index value indicates the hrStorageTable index for this storage device. The value indicates the hrDeviceTable index for the printer which uses this storage device. Returns status if attempting to perform a Get on this OID with no storage device is installed.
prtStorageRefTable	1.3.6.1.4.1.11.2.3.9.4.2.2.5.2
INT ram_disk_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1.1	INTEGER	read-write	Returns or controls RAM disk support. eOFF turns off the RAM disk functionality. eOn turns on the RAM disk functionality and creates a RAM disk whose size is controlled by the RAM-DISK-SIZE object. eAuto turns on the RAM disk functionality and creates a RAM disk size determined by the printer based on installed options and other memory related settings. Additional information: Returns or controls RAM disk support. eOFF turns off the RAM disk functionality. eOn turns on the RAM disk functionality and creates a RAM disk whose size is controlled by the RAM-DISK-SIZE object. eAuto turns on the RAM disk functionality and creates a RAM disk size determined by the printer based on the amount of installed memory. The automatic size will be 25 percent of all memory above 4MB.
INT ram_disk_size	1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1.2	INTEGER	read-write	Returns or controls the size of the RAM disk. The device POS specifies the minimum memory requirements. The object MAXIMUM-RAM-DISK-MEMORY specifies the maximum memory available for the RAM disk. Additional information: Returns or controls the size of the RAM disk. The values that can be set depend on the current setting of the RAM-DISK-MODE object, and the amount of memory available above 4MB. Use the MAXIMUM-RAM-DISK-MEMORY object to determine the amount of additional memory available for the RAM disk.
remote_procedure_call	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13
resource_manager	1.3.6.1.4.1.11.2.3.9.4.2.1.1.12
INT resource_saving	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1.6	INTEGER	read-write	Returns or changes PDL resource saving. Resource saving stores a PDL's permanent soft resources, like fonts, even when another PDL is active. Resource saving is also called environment saving. When eOff, resource saving is disabled. When ON, resource saving is enabled and memory is set aside for each PDL based on that PDL's resource saving memory size object, to store that PDL's permanent soft resources. When eAuto, resource saving is enabled and memory space for each installed PDL is determined automatically. The device POS should document what values are legal when only one PDL is installed. Additional information: When PCL (including PCL/XL) is the only PDL installed in LaserJet 4050 Series, eOn is not a legal value. Attempting to set this object to eOn with a PCL-only printer will result in a status of being returned. When Postscript is installed and less than 8 Megabytes of RAM are present, resource saving is not available. The only valid value for this object is eOff. Attempting to set this object to eOn or eAuto will cause to be returned. When Postscript and 8 Megabytes or more of RAM are installed, all values are valid, provided I/O Buffering, Mopying, or Ram Disk have not consumed the needed memory. This object is only supported if Postscript is resident in the printer.
rpc_bind	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3
OCT rpc_bind_protocol_address	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.1.2	OCTET STRING	read-write	Array of Berkeley sockets style protocol addresses used to bind RPC to a communications protocol family. Setting an instance of this array object to a zero length binary value disables the transport protocol indicated by that instance. All multi-bytes fields are in network (or big-endian) order. Bytes 1 and 2 indicate the transport protocol. Some of the transport protocol mapping information can be found in RFC 1010 Assigned Numbers. A list of interesting transport protocol number mappings include: Protocol \| Number ---------+------- UDP/IP \| 17 IPX \| 1000 MLC \| 4660 Bytes 3 and 4 indicate the address family. The address family uses the same mapping as the BSD sockets address family. A list of interesting address family mappings include: Address Family \| Number ---------------+------- Internet \| 2 NetWare \| 6 MLC \| 22136 The format the fifth and following bytes is dependent on the address family. For the Internet address family, bytes 5 and 6 contain the port number, bytes 7 through 10 contain the IP address, and the following eight bytes are unused. For NetWare, bytes 5 through 8 are the network number, bytes 9 through 14 are the node number, and bytes 15 and 16 are the socket number. Additional information: The length of the binary value is zero if the instance of an object in the rpc-bind-protocol-address array is not in use. An unfortunate side effect of the implementation is initializing the mass storage device sets this object back to the factory default value. Returns status if attempting to access this object and there is no storage device is installed.
INT rpc_bind_statistic_successful	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3.2.1	INTEGER	read-only	A counter indicating the number of RPC bind (RPC program number 100000, version 2) requests that completed successfully. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT rpc_bind_statistic_unsuccessful	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3.2.2	INTEGER	read-only	A counter indicating the number of RPC bind (RPC program number 100000, version 2) requests that completed unsuccessfully. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
OCT rpc_bind_test_return_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3.1.1	OCTET STRING	write-only	This test object that will not be supported in any released product. Setting this object allows the next RPC bind call return code to be specified. The POS will specify the binary format. Additional information: A one byte value. value \| meaning ------+------------------ 1 \| Next GetPort or GetAddr will receive port 0 \| (indicating the service is not supported). 2 \| Next Dump will receive an empty table.
OCT rpc_bound_protocol_address	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2.3	OCTET STRING	read-only	An array of Berkeley sockets style protocol addresses that the NFS service has been bound to successful. The format is that same as the array of RPC-BIND-PROTOCOL- ADDRESS of objects. Additional information: Returns status if attempting to access this object and there is no storage device is installed.
rpc_services	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3
INT rpc_statistic_successful	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2.1	INTEGER	read-only	A counter indicating the number of RPC requests that completed successfully (reply_data stat is SUCCESS). The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT rpc_statistic_unsuccessful	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2.2	INTEGER	read-only	A counter indicating the number of RPC requests that completed unsuccessfully (reply_data stat is not SUCCESS). The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
OCT rpc_test_return_code	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.1.1	OCTET STRING	write-only	This test object that will not be supported in any released product. Setting this object allows the next RPC call return code to be specified. The POS will specify the binary format. Additional information: The format of the binary data is a one of three formats. The first format is no binary data, which indicates the next RPC reply should not be modified. The other two formats are described in RFC 1057 and encoded using XDR (i.e. the value is the data used to instead of the actual RPC reply). The second format is when reply_stat is MSG_ACCEPTED and accept_stat is something other than SUCCESS. The third format is when reply_stat is MSG_DENIED. Notice that all RPC replies that do not contain any 'results' are supported.
INT run_location	1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.21	INTEGER	read-write	Returns or changes the location from which code executes. The object allows the user to pick a memory bank to run code from which is different than the default running code bank. A value of 0 means the code executes from the default code bank, which should be documented in the device POS. The list of supported values should be documented in the device POS. Setting to an unsupported value causes the device to return . Additional information: Returns or changes the location from which code should be run. The object allows the user to pick a ram bank to run code from which is potentially faster than the onboard ROM. LaserJet 8100 Series and LaserJet 8000 Series support values of 0,4-9. A value of 0 means run code from default ROM device. Values other than 0 indicate a valid RAM bank of size >= 8MBs. Setting to an unsupported value causes the printer to leave the run location set to its previous value.
OCT scanned_media_duplex_charge	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.4	OCTET STRING	read-write	Charge for each duplex page scanned, for this media size.
INT scanned_media_duplex_count	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.3	INTEGER	read-only	Total number of duplex pages scanned, for this media size.
OCT scanned_media_simplex_charge	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.2	OCTET STRING	read-write	Charge for each simplex page printed in this media size.
INT scanned_media_simplex_count	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.1	INTEGER	read-only	Total number of simplex pages scanned, for this media size. Additional information: The 5 usage (simplex/duplex count, simplex/duplex click charge and paper size total) objects described here and below detail the usage for the scanner for each paper size defined in the PCL Implementor's Guide and in the Media Size Table in the hpmib.txt. The OID binding is based on the click attribute and paper size. For example: The format for the OID is as follows: 3.4.1.5.x.y \| \| \| \| \ / \| paper size / \ PRINTER-CLICK_TOTALS ROOT \ OID click attribute 1..5 x values are 1..5: 1) simplex count 2) simplex click charge 3) duplex count 4) duplex click charge 5) printer or scanner paper size total (i.e. depends if the root OID is referrring to the printer or scanner). y : paper size as defined in the Media Size Table in the hpmib.txt The click charge objects are of data type real and have a single digit of precision. Setting these objects to more than a single digit of precision will cause truncation at a single digit, for example, if click charge is set to 15.475 and later retrieved with a get, the value will be 15.400 for this object.
OCT scanned_media_total_charge	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1.5	OCTET STRING	read-only	The total charge for pages scanned, for this media size.
scanned_media_usage	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.1
scanner	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2
INT scanner_accessory_adf_sheet_count	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.20	INTEGER	read-only	Total number of sheets that have been fed through the Automatic Document Feed (ADF) accessory. Additional information: The Automatic Document Feed (ADF) count is incremented each time a sheet feeds through the ADF.
INT scanner_accessory_cleaning_count	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.23	INTEGER	read-only	The number of sheets scanned since the last cleaning was performed. Additional information: The number of sheets that have gone through the ADF since the last cleaning was performed.
INT scanner_accessory_cleaning_interval	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.22	INTEGER	read-only	Recommended cleaning interval in units of sheets scanned. Additional information: Recommended cleaning interval is in units of sheets scanned.
STR scanner_accessory_control_panel_user_interface_revision	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.30	DisplayString	read-only	Revision of the control panel user interface firmware. Additional information: Revision of the copy processor user interface firmware shipped on the disk.
STR scanner_accessory_copy_processor_boot_revision	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.27	DisplayString	read-only	Boot ROM revision of scanner copy processor firmware. Boot code to initialize the copy processor, establish communications with the scanner, and load the runtime code. Additional information: Boot ROM revision of the Pixel Magic - Copy Processor firmware is downloaded from the scanner after the attached scanner establishes communications to the printer.
STR scanner_accessory_copy_processor_runtime_revision	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.28	DisplayString	read-only	Revision of the runtime firmware for the scanner copy processor. Runtime code which retrieves scanned data from the scanner and sends it to other devices such as a printer or PC host. Additional information: Revision of Pixel Magic - Copy Processor firmware shipped on the disk which is download into RAM for execution.
INT scanner_accessory_flatbed_scan_count	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.21	INTEGER	read-only	Total number of scans performed by a flatbed scanner accessory. Additional information: The count is only incremented when a sheet is scanned on the FLATBED.
INT scanner_accessory_maintenance_count	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.25	INTEGER	read-only	The number of sheets scanned since the last maintenance was performed. Additional information: The number of sheets that have gone through the ADF since the last maintenance was performed.
INT scanner_accessory_maintenance_interval	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.24	INTEGER	read-only	Recommended maintenance interval in units of sheets scanned. Additional information: Recommended maintenance interval is in units of sheets scanned.
STR scanner_accessory_model_number	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.19	DisplayString	read-only	Model number of the scanner accessory. This string should only use characters from the US-ASCII code set. Additional information: Model number for the Fujitsu scanner.
OCT scanner_accessory_nvram	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.33	OCTET STRING	read-only	Returns the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: Read bytes 0..39 of the NVRAM in the scanner. The Fujitsu Controller board has a total of 128 bytes of NVRAM.
OCT scanner_accessory_nvram2	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.34	OCTET STRING	read-only	Returns the second part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: Read bytes 40..79 of the NVRAM in the scanner. The Fujitsu Controller board has a total of 128 bytes of NVRAM.
OCT scanner_accessory_nvram3	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.35	OCTET STRING	read-only	Returns the third part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: Read bytes 80..119 of the NVRAM in the scanner. The Fujitsu Controller board has a total of 128 bytes of NVRAM.
OCT scanner_accessory_nvram4	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.36	OCTET STRING	read-only	Returns the fourth part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: Read bytes 120..127 of the NVRAM in the scanner. The Fujitsu Controller board has a total of 128 bytes of NVRAM.
STR scanner_accessory_rom_revision	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.26	DisplayString	read-only	ROM revision of the scanner accessory firmware. Additional information: ROM revision of the Fujitsu scanner is downloaded from the scanner after the attached scanner establishes communications to the printer.
INT scanner_accessory_serial_number	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.18	INTEGER	read-only	Identifies the serial number for the scanner accessory. If this is a writable object, the POS should indicate the maximum supported string length. This string should only use characters from the US-ASCII code set. Additional information: The serial number is 5 digit decimal number.
STR scanner_accessory_service_agent_revision	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.29	DisplayString	read-only	Revision of scanner service agent firmware. Service agent which accepts scanned data and processes scanner copy processor requests, resident in a device such as a printer or PC host. Additional information: Revision of the Scanner Service Agent firmware shipped on the disk as a Service Provider entity to retrieve scanned data from the scanner.
scanner_accounting	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2
INT self_test	1.3.6.1.4.1.11.2.3.9.4.2.1.1.5.1	INTEGER	read-write	Writing this object allows a device self test to be started. Reading this object provides an indication what self-test is currently executing, if any. Actual self-test operation is device specific. A self test may not be allowed at any arbitrary time. If the device supports the requested self test, but can not start the execution of the self test when requested, the device will respond with . If a non-destructive self test is being started, the device will generate a response before the self test is completed. RECOMMENDATION: If the device is ready (i.e. the NOT- READY-PRINTER object does not contain any items, except maybe being off-line) and is idle (i.e. the NOT-IDLE object does not contain any items), this request should always succeed. This provides a mechanism for driver writers to always determine if the action will succeed or not. Additional information: The eNonDestructiveSelfTest performs limited testing on the printer and its attached paper handling devices. After the self-test is complete a configuration page is printed. The recommended way to cause a configuration page to be printed is to use the PRINT-INTERNAL-PAGE object. Setting this object to eNonDestructiveSelfTest results in a status of and a value of eNonDestructiveSelfTest being returned. If the printer is not idle (whether printing an external job or printing an internal page), this action will be delayed until the next job boundary. See the PRINT-INTERNAL-PAGE object for more details.
STR serial_number	1.3.6.1.4.1.11.2.3.9.4.2.1.1.3.3	DisplayString	read-only	Identifies the serial number for the device. If the SERIAL-NUMBER object is set by the user, then setting the object does not need to be protected. If the SERIAL-NUMBER object is set at the factory, then the SERVICE-PASSWORD object must be set correctly before the SERIAL-NUMBER object is writable. If this is a writable object, the POS should indicate the maximum supported string length. If possible, encode the serial number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: This value IS AFFECTED BY NVRAM resets, it is set to the default value of XXXXXXXXXX, when a NVRAM init is done.
settings_file_system	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.1
settings_intray	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.1
settings_io	1.3.6.1.4.1.11.2.3.9.4.2.1.2.1.1
settings_jetsend	1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.1
settings_jetsend_contact	1.3.6.1.4.1.11.2.3.9.4.2.1.3.8.3.1
settings_job	1.3.6.1.4.1.11.2.3.9.4.2.1.1.6.1
settings_marking_agent	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.5.1
settings_mass_storage_bd	1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.1
settings_nfs_server	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.1
settings_outbin	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.4.1
settings_pdl	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.1
settings_print_media	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.8.1
settings_prt_eng	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.1
settings_rpc	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.1
settings_rpc_bind	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3.1
settings_scanner	1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1
settings_spooler	1.3.6.1.4.1.11.2.3.9.4.2.1.2.4.1
settings_system	1.3.6.1.4.1.11.2.3.9.4.2.1.1.1
simm	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1
simm1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1
simm1_bank	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6
simm1_bank1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1
INT simm1_bank1_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1.2	INTEGER	read-only	Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 1. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM1-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.
INT simm1_bank1_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.1.1	INTEGER	read-only	Returns an indication of the type of option installed in Bank 1 of SIMM slot 1. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.
simm1_bank2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2
INT simm1_bank2_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2.2	INTEGER	read-only	Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 1. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM1-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.
INT simm1_bank2_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.6.2.1	INTEGER	read-only	Returns an indication of the type of option installed in Bank 2 of SIMM slot 1. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.
INT simm1_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.5	INTEGER	read-only	Returns an indication of the capacity of the SIMM installed in SIMM slot 1. The capacity is dependent on the type of option, as indicated by the SIMM1-TYPE object. This object has no meaning if the installed option type is eUnknown or eReadOnlyMemory. This object contains the size, in bytes, if the installed option type is eVolatileRandomAccessMemory, eNonVolatileRandomAccessMemory, eFlashMemory, or eDiskDrive. If the type of the installed option is eRamRom, this object contains the size, in bytes, of the random access memory. If the type of the installed option is eInputPHD, the capacity indicates the number of input trays supported by the installed option. If the type of the installed option is eOutputPHD, the capacity indicates the number of output bins supported by the installed option. If the type of the installed option is eIOCard, the capacity indicates the number of logical I/O ports supported by the I/O card. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM1-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the SIMM is returned.
INT simm1_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.1.4	INTEGER	read-only	Returns an indication of the type of option installed in SIMM slot 1. eEmpty means the device did not detect any option installed in the interface slot. eUnknown means the device doesn't recognize the installed option. eUnSupported means the device recognizes the installed option, but does not support the option. eReadOnlyMemory means the installed option contains ROM Ics. eVolatileRandomAccessMemory means the installed option contains RAM ICs that loose data when the power is turned off. eNonVolatileRandomAccessMemory means that the installed option contains RAM ICs that do not loose data when the power is turned off. eFlashMemory means that the installed option contains a type of non-volatile RAM that needs to be erased before it can be written. eDiskDrive means the installed option contains a disk drive. eRamRom means the installed option contains both volatile random access memory and read only memory. eInputPHD means the installed option is an input paper handling device. eOutputPHD means the installed option is an output paper handling device. eIOCard means the installed option is an I/O card. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4050 Series. eRamRom is used to denote LaserJet 4050 Series's combo simm.
simm2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2
simm2_bank	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6
simm2_bank1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1
INT simm2_bank1_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1.2	INTEGER	read-only	Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM2-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.
INT simm2_bank1_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.1.1	INTEGER	read-only	Returns an indication of the type of option installed in Bank 1 of SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.
simm2_bank2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2
INT simm2_bank2_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2.2	INTEGER	read-only	Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM2-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.
INT simm2_bank2_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.6.2.1	INTEGER	read-only	Returns an indication of the type of option installed in Bank 2 of SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.
INT simm2_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.5	INTEGER	read-only	Returns an indication of the capacity of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4050 Series. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM2-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the SIMM is returned.
INT simm2_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.2.4	INTEGER	read-only	Returns an indication of the type of option installed in SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4050 Series. eRamRom is used to denote LaserJet 4050 Series's combo simm.
simm3	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3
simm3_bank	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6
simm3_bank1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.1
INT simm3_bank1_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.1.2	INTEGER	read-only	Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM3-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.
INT simm3_bank1_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.1.1	INTEGER	read-only	Returns an indication of the type of option installed in Bank 1 of SIMM slot 3. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.
simm3_bank2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.2
INT simm3_bank2_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.2.2	INTEGER	read-only	Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM3-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.
INT simm3_bank2_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.6.2.1	INTEGER	read-only	Returns an indication of the type of option installed in Bank 2 of SIMM slot 3. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.
INT simm3_capacity	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.5	INTEGER	read-only	Returns an indication of the capacity of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4050 Series. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM3-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the simm is returned.
INT simm3_type	1.3.6.1.4.1.11.2.3.9.4.2.1.1.4.1.3.4	INTEGER	read-only	Returns an indication of the type of option installed in SIMM slot 3. See SIMM1-TYPE for a description.
INT sleep_mode	1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2	INTEGER	read-write	Returns eTrue if the device is in energy saving sleep mode, otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes the device to wake up, if it is in sleep mode. Setting SLEEP-MODE to eTrue causes the device to go into sleep mode. Additional information: This object returns eTrue if the device is in energy saving sleep mode, otherwise it returns eFalse. Setting this object to eTrue while the printer is awake will not change the printer's current state and will return status. NOTE: This object should behave this way when the printer does not have an instant-on fuser. Setting this object to eTrue while printer is already in Sleep Mode will not change the printer's current state and will return status. Setting this object to eFalse while printer is already awake will not change the printer's current state and will return status. Setting this object to eFalse while the printer is asleep causes the device to wake up.
source_subsystem	1.3.6.1.4.1.11.2.3.9.4.2.1.2
spooler	1.3.6.1.4.1.11.2.3.9.4.2.1.2.4
status_file_system	1.3.6.1.4.1.11.2.3.9.4.2.1.1.10.2
status_mass_storage_bd	1.3.6.1.4.1.11.2.3.9.4.2.1.1.15.2
status_nfs_server	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.2.2
status_pdl	1.3.6.1.4.1.11.2.3.9.4.2.1.3.3.2
status_prt_eng	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.2
status_rpc	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.2
status_rpc_bind	1.3.6.1.4.1.11.2.3.9.4.2.1.1.13.3.3.2
status_system	1.3.6.1.4.1.11.2.3.9.4.2.1.1.2
status_xip	1.3.6.1.4.1.11.2.3.9.4.2.1.1.14.2
system	1.3.6.1.4.1.11.2.3.9.4.2.1.1
tables	1.3.6.1.4.1.11.2.3.9.4.2.1.7
test	1.3.6.1.4.1.11.2.3.9.4.2.1.1.5
INT tray1_media_size_loaded	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.1	INTEGER	read-write	Returns the media size that is currently configuredconfigured in tray #1. This object can be set to indicate the media size currently loaded, if the printer supports input trays that can not sense the media size. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document.
INT tray1_phd	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.1.12	INTEGER	read-only	Provides the number of the Paper Handling Device that contains this input tray. Additional information: The internal trays belong to device 0, which is the base engine. The envelope feeder (if supported) is considered to be device 1 and the external input devices can number between 2 and 6 depending on individual user configurations.
INT tray2_media_size_loaded	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.1	INTEGER	read-only	Returns the media size that is currently configured in tray #2. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of to be returned. If the tray is empty, the size that the tray is configured for will be returned. If Tray 2 is a 500-sheet standard tray, eJISB5 and eUSExecutive are not valid values.
INT tray2_phd	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.12	INTEGER	read-only	Provides the number of the Paper Handling Device that contains this input tray.
INT tray3_media_size_loaded	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3.1	INTEGER	read-only	Returns the media size that is currently configured in tray #3. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of to be returned. If the tray is empty, the size that the tray is configured for will be returned.
INT tray3_phd	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.3.12	INTEGER	read-only	Provides the number of the Paper Handling Device that contains this input tray.
INT tray4_phd	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.4.12	INTEGER	read-only	Provides the number of the Paper Handling Device that contains this input tray.
INT tray5_media_size_loaded	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.5.1	INTEGER	read-only	Returns the media size that is currently configured in tray #5. Complete list of supported media sizes along with their dimensions are listed in the ''Media Size Table'' near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of to be returned. If the tray is empty, the size that the tray is configured for will be returned.
INT tray5_phd	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.5.12	INTEGER	read-only	Provides the number of the Paper Handling Device that contains this input tray.
INT tray6_phd	1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.6.12	INTEGER	read-only	Provides the number of the Paper Handling Device that contains this input tray.
OCT usage_average_toner_coverage	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.3	OCTET STRING	read-only	Reports the average toner area coverage of all pages printed over the life of the device. Counts pixels on each page, divides pixel count by pixels possible on a page to give the percentage of coverage, and keeps a rolling average percent weighted by area printed.
STR usage_instructions_line1	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.5	DisplayString	read-write	The first line of usage instructions for the device user.Appears on Line 1 of the usage page.
STR usage_instructions_line2	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.6	DisplayString	read-write	The second line of usage instructions for the device user.Appears on Line 1 of the usage page.
STR usage_instructions_line3	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.7	DisplayString	read-write	The third line of usage instructions for the device user.Appears on Line 1 of the usage page.
STR usage_instructions_line4	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.8	DisplayString	read-write	The fourth line of usage instructions for the device user.Appears on Line 1 of the usage page.
OCT usage_printer_total_charge	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.2	OCTET STRING	read-only	Total printer charge for all paper sizes printed.
OCT usage_scanner_total_charge	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.2.2	OCTET STRING	read-only	Total scanner charge or cost for all paper sizes scanned.
INT usage_staple_count	1.3.6.1.4.1.11.2.3.9.4.2.1.1.16.1.4	INTEGER	read-only	Total number of staples used.
INT xip_statistic_data_in_dropped	1.3.6.1.4.1.11.2.3.9.4.2.1.1.14.2.2	INTEGER	read-only	A counter indicating the number of XIP data in datagrams that were dropped (typically due to the printer being flooded with XIP requests ). The POS should state if a power cycle causes the counter is be reset to zero. Additional information: Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
INT xip_statistic_processed	1.3.6.1.4.1.11.2.3.9.4.2.1.1.14.2.1	INTEGER	read-only	A counter indicating the number of XIP requests that were processed. The POS should state if a power cycle causes the counter is be reset to zero. Additional information: The number of XIP datagrams that have been received by the XIP service. Reset to the factory default value after a power cycle. Returns status if attempting to access this object and there is no storage device is installed.
xport_interface	1.3.6.1.4.1.11.2.3.9.4.2.1.1.14

RFC description

Provides model-specific management objects for HP LaserJet Series 4050 printers connected via JetDirect print servers.

Start monitoring HP LaserJet 4050 series printer with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download LaserJet-Series4050-MIB