All MIBs › LANNET-MIB
Category: Network Management
Description: Manages LANNET hub and network device configuration and status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is LANNET-MIB?
LANNET-MIB is a legacy enterprise MIB from LANNET (an early Ethernet/Token Ring hub and chassis vendor later part of Madge/Lucent) covering the hardware inventory and status of its modular hub/chassis systems. It exposes chassis-level hardware inventory objects — hardware type, number of slots, and counts of Ethernet, Token Ring, FDDI, and LocalTalk buses present in the chassis — plus a generic agent group table (chGenAgTable) for per-agent/module identification, and a chassis reset control object. Its monitoring emphasis is hardware inventory and configuration status: confirming the physical chassis composition (slot count, bus types) matches expectations and using chFullConfig/chReset for configuration snapshot and remote reset operations, a basic but important hardware-management capability for a modular hub. It predates and has no dependency on modern IF-MIB-style interface conventions, relying instead on its own chassis/agent object model. It was used in legacy enterprise LAN deployments built around LANNET's multi-bus modular hub chassis products before such gear was largely replaced by switched Ethernet. Engineers can download the LANNET-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in LANNET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- LANNET modular Ethernet/Token Ring hub chassis
Monitoring Examples
An operator would poll chNumberOfSlots, chNumberOfEthernetBuses, chNumberOfTRBuses, and chNumberOfFDDIBuses against the chGenAgTable/chGenAgEntry per-module records to confirm the physical chassis configuration (which slots hold which bus type) matches the intended design; a mismatch between expected and reported chHWType or bus counts would indicate a miscabled or failed module, and chReset could be invoked to remotely reset the chassis if a module became unresponsive.
What Can Be Monitored
- chassis hardware type
- slot count
- bus type counts (Ethernet/Token Ring/FDDI/LocalTalk)
- per-module agent identification
- chassis configuration snapshot
- remote chassis reset
This MIB depends on
Related MIBs
Imported Objects
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| NetworkAddress | |
| TimeTicks | |
| enterprises |
From RFC1158-MIB
| DisplayString |
From RFC1212
| OBJECT-TYPE |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| lannet | 1.3.6.1.4.1.81 | |||
| chassis | 1.3.6.1.4.1.81.7 | |||
| INT chHWType | 1.3.6.1.4.1.81.7.1 | INTEGER | read-only | Indicates type of enclosure in which the LANNET SNMP agent operates. |
| INT chNumberOfSlots | 1.3.6.1.4.1.81.7.2 | INTEGER | read-only | Number of manageable slots in the chassis. In LANNET implementation it describes the number of manageable slots in the chassis (not all slots should be ocuppied). |
| INT chNumberOfEthernetBuses | 1.3.6.1.4.1.81.7.3 | INTEGER | read-only | Indicates the number of internal Ethernet buses provided by the box. |
| INT chNumberOfTRBuses | 1.3.6.1.4.1.81.7.4 | INTEGER | read-only | Indicates the number of internal Token Ring buses provided by the box. |
| INT chNumberOfFDDIBuses | 1.3.6.1.4.1.81.7.5 | INTEGER | read-only | Indicates the number of internal FDDI buses provided by the box. |
| INT chNumberOfLocalTalkBuses | 1.3.6.1.4.1.81.7.6 | INTEGER | read-only | Indicates the number of internal Local Talk buses provided by the box. |
| INT chReset | 1.3.6.1.4.1.81.7.7 | INTEGER | read-write | Setting the value of this attribute to ON is interpreted as a reset command for the whole chassis. It initiates a complete reinitialisation of the chassis and of all the devices incorporated inside the chassis. |
| OCT chFullConfig | 1.3.6.1.4.1.81.7.8 | OCTET STRING | read-only | Full configuration message retrieved by LANNET management stations at periodic interrogation times. Coded in compact internal LANNET application format. |
| chAg | 1.3.6.1.4.1.81.7.9 | |||
| chGenAgTable | 1.3.6.1.4.1.81.7.9.1 | not-accessible | Table of configuration attributes common to all SNMP agents in LANNET hubs. | |
| chGenAgEntry | 1.3.6.1.4.1.81.7.9.1.1 | not-accessible | An entry in the table, containing configuration attributes for a single agent. | |
| INT chGenAgId | 1.3.6.1.4.1.81.7.9.1.1.1 | INTEGER | read-only | Agent index for identifying the agent.Takes the value of the slot number where the agent card is inserted. For box agents the value of chGenAgId is chNumberOfSlots+1. |
| INT chGenAgType | 1.3.6.1.4.1.81.7.9.1.1.2 | INTEGER | read-only | Agent type. |
| INT chGenAgMgmtIfType | 1.3.6.1.4.1.81.7.9.1.1.3 | INTEGER | read-only | This attribute describes one of the interfaces of agents existing on LANNET modules and their type. Value 'none' defines the lack of an interface recognized by the management console. Any other value defines an interface whose type is recognized by the management console and may be used as a management channel. |
| OCT chGenAgAddr | 1.3.6.1.4.1.81.7.9.1.1.4 | OCTET STRING | read-only | This attribute defines an unique address by which the agent may be addressed by the management console. The address format should be consistent with the type defined by chGenAgMgmtIfType. |
| OID chGenAgSpecificOID | 1.3.6.1.4.1.81.7.9.1.1.5 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| chLntAgTable | 1.3.6.1.4.1.81.7.9.2 | not-accessible | Table of configuration attributes of LANNET SNMP box agents in LANNET hubs. | |
| chLntAgEntry | 1.3.6.1.4.1.81.7.9.2.1 | not-accessible | An entry in the table, containing configuration attributes for a single agent. | |
| INT chLntAgId | 1.3.6.1.4.1.81.7.9.2.1.1 | INTEGER | read-only | Agent index for identifying the agent. Identical to the index in chGenAgTable for the described agent. |
| IP chLntAgSLIPAddress | 1.3.6.1.4.1.81.7.9.2.1.2 | IpAddress | read-only | IP address of the SLIP channel of the agent |
| OCT chLntAgSWVersion | 1.3.6.1.4.1.81.7.9.2.1.3 | OCTET STRING | read-only | ASCII string for description and display of the agent software version. |
| OCT chLntAgKernelVersion | 1.3.6.1.4.1.81.7.9.2.1.4 | OCTET STRING | read-only | ASCII string for description and display of the agent operating system (kernel) version. |
| OCT chLntAgCoprocSWVersion | 1.3.6.1.4.1.81.7.9.2.1.5 | OCTET STRING | read-only | ASCII string describing the software version of the agent's coprocessor. |
| OCT chLntAgSWFault | 1.3.6.1.4.1.81.7.9.2.1.6 | OCTET STRING | read-only | System fault emitted by agent software. It covers faults detected by the agent operating system and drivers. EnterpriseSpecific traps mechanism is used for transfering these traps to the management system. |
| INT chLntAgMgmtBusSelection | 1.3.6.1.4.1.81.7.9.2.1.7 | INTEGER | read-only | Attribute describing the number of the bus on which management data are reported. |
| INT chLntAgCoprocCommStatus | 1.3.6.1.4.1.81.7.9.2.1.8 | INTEGER | read-only | Attribute describing the status of the communication between the agent and its coprocessor. |
| INT chLntAgCommDebugMode | 1.3.6.1.4.1.81.7.9.2.1.9 | INTEGER | read-write | Attribute describing the agent mode in which communication problem traps are sent to managers (value 'on') or are not sent to managers (value 'off'). |
| INT chLntAgConfigChangeTraps | 1.3.6.1.4.1.81.7.9.2.1.10 | INTEGER | read-write | The value of this attributes determines whether or not the agent sends Configuration Change traps to the manager. |
| INT chLntAgFaultTraps | 1.3.6.1.4.1.81.7.9.2.1.11 | INTEGER | read-write | The value of this attributes determines whether or not the agent sends Fault traps to the manager. |
| INT chLntAgTrafficThreshTraps | 1.3.6.1.4.1.81.7.9.2.1.12 | INTEGER | read-write | The value of this attributes determines whether or not the agent sends Traffic Threshold traps to the manager. |
| INT chLntAgGroupEnrollDeenrollTraps | 1.3.6.1.4.1.81.7.9.2.1.13 | INTEGER | read-write | The value of this attributes determines whether or not the agent sends Group Enrollment and Group Deenrollment traps to the manager. |
| INT chLntAgSoftFaultTraps | 1.3.6.1.4.1.81.7.9.2.1.14 | INTEGER | read-write | The value of this attributes determines whether or not the agent sends Software Fault traps to the manager. |
| INT chLntAgHubEnrollTraps | 1.3.6.1.4.1.81.7.9.2.1.15 | INTEGER | read-write | The value of this attributes determines whether or not the agent sends periodic Hub Enrollment traps to the manager. |
| INT chLntAgTempThreshTraps | 1.3.6.1.4.1.81.7.9.2.1.16 | INTEGER | read-write | The value of this attributes determines whether or not the agent sends Temperature Threshold traps to the manager. |
| OID chLntAgSpecificOID | 1.3.6.1.4.1.81.7.9.2.1.17 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| OCT chLntAgLastAddrConfig | 1.3.6.1.4.1.81.7.9.2.1.18 | OCTET STRING | read-only | Configuration attribute describing the last physical address detected at each port. Coded in internal LANNET application format. |
| OCT chLntAgSecAddrConfig | 1.3.6.1.4.1.81.7.9.2.1.19 | OCTET STRING | read-only | Configuration attribute describing the configuration of the secure addresses. Coded in internal LANNET application format. |
| INT chLntAgSoftwareStatus | 1.3.6.1.4.1.81.7.9.2.1.20 | INTEGER | read-write | Describes configuration of the firmware on this agent. unLoadable(1) - is returned by agents which do not support the Software Download feature; loaded(2) - is returned by agents with loaded software; downLoading(3) - when the attribute is set to this value by manager, it triggers the Software Download procedure. When procedure finished, agent software will restablish value loaded(2). |
| OCT chLntAgConfigurationSymbol | 1.3.6.1.4.1.81.7.9.2.1.21 | OCTET STRING | read-write | Defines the Configuration Symbol attached to any hardware module manufactured by LANNET. One single character A..Z defines the CS version. For older modules which did not support this option on SNMP character '*' will be returned. |
| INT chLntAgIntTemp | 1.3.6.1.4.1.81.7.9.2.1.22 | INTEGER | read-only | Internal temperature measured by the temperature sensor placed on the agent card. Expressed in Celsius degrees. |
| OCT chLntAgBootVersion | 1.3.6.1.4.1.81.7.9.2.1.23 | OCTET STRING | read-only | ASCII string for description and display of the agent boot software version. |
| chMgr | 1.3.6.1.4.1.81.7.10 | |||
| INT chMgrTrapRepStatus | 1.3.6.1.4.1.81.7.10.1 | INTEGER | read-write | Value 'on' indicates that SNMP agent should send SNMP traps (traffic ex- cluded) to the manager. |
| INT chMgrContPerfRep | 1.3.6.1.4.1.81.7.10.2 | INTEGER | read-write | Value 'on' indicates that the SNMP agent should send traffic SNMP traps to the manager. |
| INT chMgrMngmtState | 1.3.6.1.4.1.81.7.10.3 | INTEGER | read-write | Attribute to be set by manager in order to instruct the agent to enter into a management session with the console. Setting this value to 'on' has the effect of performing an 'I am your manager' action upon the agent. |
| chHW | 1.3.6.1.4.1.81.7.11 | |||
| chHWPSUTable | 1.3.6.1.4.1.81.7.11.1 | not-accessible | Table of configuration attributes for Power Supply Units. This table can be retrieved only from agents equipped with adequate hardware. | |
| chHWPSUEntry | 1.3.6.1.4.1.81.7.11.1.1 | not-accessible | An entry in the table, containing configuration attributes for a single Power Supply Unit. | |
| INT chHWPSUId | 1.3.6.1.4.1.81.7.11.1.1.1 | INTEGER | read-only | PSU index for identifying the PSU. |
| INT chHWPSUActivityStatus | 1.3.6.1.4.1.81.7.11.1.1.2 | INTEGER | read-only | This attribute defines the status of the PSU in what concerns supplying power to the chassis. NotActive - indicates a disabled or defective PSU which cannot supply power to the chassis. Dormant - indicates a functional PSU which is installed for backup purposes and can at any moment supply power to the devices in the chassis. Active - indicates that the PSU supplies power to the chassis. |
| INT chHWPSULocation | 1.3.6.1.4.1.81.7.11.1.1.3 | INTEGER | read-only | Describes the location (internal or external) of the PSU. |
| INT chHWPSUVoltage | 1.3.6.1.4.1.81.7.11.1.1.4 | INTEGER | read-only | Indicates voltage of PSU expressed in miliVolts. |
| INT chHWIntTempWarning | 1.3.6.1.4.1.81.7.11.2 | INTEGER | read-only | Fault condition indicating that the temperature measured by one of the sensors internal to the box exceeded chHWIntTempThresh. |
| INT chHWIntTempThresh | 1.3.6.1.4.1.81.7.11.3 | INTEGER | read-write | Internal enclosure temperature threshold value, expressed in degrees Celsius. When exceeded, a trap is sent to the management console. |
| INT chHWPeakIntTemp | 1.3.6.1.4.1.81.7.11.4 | INTEGER | read-only | Maximum internal temperature inside the chassis. It is the maximum of the temperature values detected by different temperature sensors inside the box. |
| genGroup | 1.3.6.1.4.1.81.8 | |||
| genGroupTable | 1.3.6.1.4.1.81.8.1 | not-accessible | Table of configuration attributes for managed LANNET modules. Includes configuration data which are independent of the specific functionality of the module. | |
| genGroupEntry | 1.3.6.1.4.1.81.8.1.1 | not-accessible | An entry in the table, containing data about a single group. | |
| INT genGroupId | 1.3.6.1.4.1.81.8.1.1.1 | INTEGER | read-only | Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group is accessed. This value is never greater than chNumberOfSlots. |
| OCT genGroupSWVersion | 1.3.6.1.4.1.81.8.1.1.2 | OCTET STRING | read-only | ASCII string for description and display of the group software version. |
| OCT genGroupKernelVersion | 1.3.6.1.4.1.81.8.1.1.3 | OCTET STRING | read-only | ASCII string for description and display of the group kernel version. |
| INT genGroupType | 1.3.6.1.4.1.81.8.1.1.4 | INTEGER | read-only | Attribute describing the type of LANNET Ethernet group. |
| OCT genGroupDescr | 1.3.6.1.4.1.81.8.1.1.5 | OCTET STRING | read-only | Descriptor of the group in ASCII (readable) format, mainly for use with generic management applications. |
| INT genGroupNumberOfPorts | 1.3.6.1.4.1.81.8.1.1.6 | INTEGER | read-only | Number of ports in group. It is assumed that on each group the ports are assigned unique numbers in the range from 1 to genGroupNumberOfPorts. They correspond to the number of ports on the module (FRU) |
| INT genGroupNumberOfIntPorts | 1.3.6.1.4.1.81.8.1.1.7 | INTEGER | read-only | Number of internal ports (ports connected to the chassis buses) on the module. |
| INT genGroupReset | 1.3.6.1.4.1.81.8.1.1.8 | INTEGER | read-write | Setting the value of this attribute to 'on' is interpreted as a software RESET command. Sensor software is reinitialized and according to the sensor specifications, partial or total reset of the module hardware may be performed. |
| INT genGroupAutoMan | 1.3.6.1.4.1.81.8.1.1.9 | INTEGER | read-only | This attribute reflects the status of the Auto/Manual switch which defines the working mode of LANNET sensors. In the MANUAL mode no set operations may be performed on attributes related to the sensor. The sensor works according to configuration switches set by hardware and transmits all configuration information to the agent. In the AUTO mode, hardware switches are overridden by set commands. |
| OCT genGroupFullConfig | 1.3.6.1.4.1.81.8.1.1.10 | OCTET STRING | read-only | Attribute describing the full configuration of a group in internal LANNET application format. |
| INT genGroupRedun12 | 1.3.6.1.4.1.81.8.1.1.11 | INTEGER | read-write | Value ON of this attribute defines a redundancy (backup) relationship between synchronous external ports 1 and 2 on a LANNET module. |
| INT genGroupRedun34 | 1.3.6.1.4.1.81.8.1.1.12 | INTEGER | read-write | Value ON of this attribute defines a redundancy (backup) relationship between synchronous external ports 3 and 4 on a LANNET module. |
| INT genGroupRedun13_14 | 1.3.6.1.4.1.81.8.1.1.13 | INTEGER | read-write | Value ON of this attribute defines a redundancy (backup) relationship between synchronous external ports 13 and 14 on a LANNET module. |
| INT genGroupStandAloneMode | 1.3.6.1.4.1.81.8.1.1.14 | INTEGER | read-write | Value ON of this attribute indicates the sensor's operation Stand Alone mode . Internal ports are disabled and the card functions in a local star configuration toward its external ports. |
| INT genGroupInterProcCommStatus | 1.3.6.1.4.1.81.8.1.1.15 | INTEGER | read-only | This attribute describes the status of the communication between the microprocessor of the sensor and the microprocessor of the agent on cards with embedded agents. |
| INT genGroupCommStatus | 1.3.6.1.4.1.81.8.1.1.16 | INTEGER | read-only | This attribute describes the communication status of the group with the SNMP Agent as detected and reported by the agent. |
| INT genGroupHWStatus | 1.3.6.1.4.1.81.8.1.1.17 | INTEGER | read-only | This attribute describes the status of the group hardware as detected by the sensors software. |
| INT genGroupSupplyVoltageFault | 1.3.6.1.4.1.81.8.1.1.18 | INTEGER | read-only | A value 'on' of this attribute informs of a 'voltage supply out-of-range' error condition on sensor equipped with hardware which checks this condition. |
| INT genGroupIntTemp | 1.3.6.1.4.1.81.8.1.1.19 | INTEGER | read-only | Internal temperature of the enclosure as measured by the specific module instance. |
| OID genGroupSpecificOID | 1.3.6.1.4.1.81.8.1.1.20 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| OCT genGroupConfigurationSymbol | 1.3.6.1.4.1.81.8.1.1.21 | OCTET STRING | read-write | Defines the Configuration Symbol attached to any hardware module manufactured by LANNET. One single character A..Z defines the CS version. For older modules which did not support this option on SNMP character '*' will be returned. |
| genPort | 1.3.6.1.4.1.81.9 | |||
| genPortTable | 1.3.6.1.4.1.81.9.1 | not-accessible | Table of configuration attributes for managed LANNET ports. Includes configuration data which are independent of the specific functionality of the port. | |
| genPortEntry | 1.3.6.1.4.1.81.9.1.1 | not-accessible | An entry in the table, containing data about a single port. | |
| INT genPortGroupId | 1.3.6.1.4.1.81.9.1.1.1 | INTEGER | read-only | Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group containing the port is accessed. This value is never greater than chNumberOfSlots. |
| INT genPortId | 1.3.6.1.4.1.81.9.1.1.2 | INTEGER | read-only | Index which identifies the port inside the group for which this entry contains information. It generally corresponds with the number by which the port is identified and is marked on the module. This value is never greater than genGroupNumberOfPorts of the group to which the port belongs. |
| INT genPortFunctionality | 1.3.6.1.4.1.81.9.1.1.3 | INTEGER | read-only | Describes the functionality of the port according to international standards. |
| INT genPortType | 1.3.6.1.4.1.81.9.1.1.4 | INTEGER | read-only | Attribute describing the type of LANNET port. |
| OCT genPortDescr | 1.3.6.1.4.1.81.9.1.1.5 | OCTET STRING | read-only | Descriptor of the port in ASCII (readable) format, mainly for use with generic management applications. |
| INT genPortActivityStatus | 1.3.6.1.4.1.81.9.1.1.6 | INTEGER | read-only | This attribute defines the status of ports that may be part of a redundancy scheme. NotActive - indicates a disabled port which cannot transmit or receive packets even if included in a redundancy scheme. Dormant - indicates an enabled port which does not transmit or receive packets, but because it is included in a redundancy scheme, it may at any moment become responsible packet transmission and reception. Active - indicates that the port transmits and receives packets, serving as the main path in the redundant configuration. |
| OCT genPortSecurityPolicy | 1.3.6.1.4.1.81.9.1.1.7 | OCTET STRING | read-write | Security policy (Trap Only or Trap and Close) assigned to this port. The information is coded in internal LANNET format. |
| OCT genPortSecureAddresses | 1.3.6.1.4.1.81.9.1.1.8 | OCTET STRING | read-write | This attribute defines the security information (physical addresses) relevant for the entry. Coded in internal format, cryptographic methods may be used for privacy purposes. |
| INT genPortIntPortConnection | 1.3.6.1.4.1.81.9.1.1.9 | INTEGER | read-only | The value of this attribute defines the internal port to which the port is connected. A value 0 of this attribute would indicate no internal port connection (stand-alone mode). Any other positive value equals the number of the internal port. |
| INT genPortAdminStatus | 1.3.6.1.4.1.81.9.1.1.10 | INTEGER | read-write | A disabled port neither transmits nor receives. The port must be explici- tenly enabled to restore operation. For token ring ports, this attribute is read-only. |
| OID genPortSpecificOID | 1.3.6.1.4.1.81.9.1.1.11 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| genIntPort | 1.3.6.1.4.1.81.10 | |||
| genIntPortTable | 1.3.6.1.4.1.81.10.1 | not-accessible | Table of configuration attributes of LANNET internal ports. Internal ports are physical and/or logical entities which transfer information and connect LANNET modules to the internal networks (buses). | |
| genIntPortEntry | 1.3.6.1.4.1.81.10.1.1 | not-accessible | An entry in the table, containing data about a single port. | |
| INT genIntPortGroupId | 1.3.6.1.4.1.81.10.1.1.1 | INTEGER | read-only | Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group containing the internal port is accessed. This value is never greater than chNumberOfSlots. |
| INT genIntPortId | 1.3.6.1.4.1.81.10.1.1.2 | INTEGER | read-only | Index which identifies the port inside the group for which this entry contains information. This value is never greater than genGroupNumberOfIntPorts of the group to which the port belongs. |
| INT genIntPortAdminStatus | 1.3.6.1.4.1.81.10.1.1.3 | INTEGER | read-write | Defines the capability of the internal port to transmit or receive data. A disabled internal port neither transmits or receives. The port must be explicitly enabled to restore operation. |
| INT genIntPortActivityStatus | 1.3.6.1.4.1.81.10.1.1.4 | INTEGER | read-only | This attribute defines the status of internal ports that may be part of a redundancy scheme. NotActive - indicates a disabled port which cannot transmit or receive packets even if included in a redundancy scheme. Dormant - indicates an enabled port which does not transmit or receive packets, but because it is included in a redundancy scheme, it may at any moment become responsible for packet transmission and reception. Active - indicates that the port transmits and receives packets, serving as the main path in the redundant configuration. |
| INT genIntPortBusConnNumber | 1.3.6.1.4.1.81.10.1.1.5 | INTEGER | read-write | The value of this attribute defines the bus to which the internal port is connected. |
| INT genIntPortBusConnType | 1.3.6.1.4.1.81.10.1.1.6 | INTEGER | read-only | The value of this attribute defines the type of the bus to which the internal port is connected. |
| OID genIntPortSpecificOID | 1.3.6.1.4.1.81.10.1.1.7 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| softRedundancy | 1.3.6.1.4.1.81.11 | |||
| softRedundancyTable | 1.3.6.1.4.1.81.11.1 | not-accessible | Table of attributes which define software redundancy links defined by means of the LANNET chassis SNMP agents. | |
| softRedundancyEntry | 1.3.6.1.4.1.81.11.1.1 | not-accessible | An entry in the table, containing data about a single software redundancy link. | |
| INT softRedundancyId | 1.3.6.1.4.1.81.11.1.1.1 | INTEGER | read-only | Index which identifies the software redundancy link which for which the current entry provides information. |
| OCT softRedundancyName | 1.3.6.1.4.1.81.11.1.1.2 | OCTET STRING | read-write | Logical name of the software redundancy link |
| INT softRedundancyGroupId1 | 1.3.6.1.4.1.81.11.1.1.3 | INTEGER | read-write | ID of the group to which the main port on the software redundancy link belongs. This value is never greater than chNumberOfSlots. |
| INT softRedundancyPortId1 | 1.3.6.1.4.1.81.11.1.1.4 | INTEGER | read-write | ID of the main port on the software redundancy link. |
| INT softRedundancyGroupId2 | 1.3.6.1.4.1.81.11.1.1.5 | INTEGER | read-write | ID of the group to which the secondary port on the software redundancy link belongs. This value is never greater than chNumberOfSlots. |
| INT softRedundancyPortId2 | 1.3.6.1.4.1.81.11.1.1.6 | INTEGER | read-write | ID of the secondary port on the software redundancy link. |
| INT softRedundancyStatus | 1.3.6.1.4.1.81.11.1.1.7 | INTEGER | read-write | Status of the entry in the softRedundancy Table: valid(1) indicates that row is busy with meaningful values; createRequest(2) will be set by manager when creating a new row; underCreation(3) indicates that agent accepts create command and performs it; invalid(4) indicates that no meaningful values are present in the row. Managers set this value in order to transmit a 'Delete row' command to agent. |
| eth | 1.3.6.1.4.1.81.12 | |||
| ethAg | 1.3.6.1.4.1.81.12.1 | |||
| ethAgTable | 1.3.6.1.4.1.81.12.1.1 | not-accessible | Table of attributes which define configuration characteristics for LANNET chassis SNMP agents which use Ethernet as in-band management protocol. | |
| ethAgEntry | 1.3.6.1.4.1.81.12.1.1.1 | not-accessible | An entry in the table, containing data about a single Ethernet agent. | |
| INT ethAgId | 1.3.6.1.4.1.81.12.1.1.1.1 | INTEGER | read-only | Index which identifies the Ethernet agent for which the current entry provides information. |
| INT ethAgPerfBusSelection | 1.3.6.1.4.1.81.12.1.1.1.2 | INTEGER | read-write | Attribute describing the bus attached to the performance data collection hardware on those LANNET agent hardware implementations which support configuration management on multi-Ethernet bus enclosures, but performan- ce data collection on a single bus. |
| ethGroup | 1.3.6.1.4.1.81.12.2 | |||
| ethGroupTable | 1.3.6.1.4.1.81.12.2.1 | not-accessible | Table of attributes which define configuration characteristics for LANNET Ethernet modules. | |
| ethGroupEntry | 1.3.6.1.4.1.81.12.2.1.1 | not-accessible | An entry in the table, containing data about a single Ethernet module (group). | |
| INT ethGroupId | 1.3.6.1.4.1.81.12.2.1.1.1 | INTEGER | read-only | Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group is accessed. This value is never greater than chNumberOfSlots. |
| INT ethGroupFIFO | 1.3.6.1.4.1.81.12.2.1.1.2 | INTEGER | read-only | Value ON of this attribute describes an internal FIFO error sensed by the internal hardware mechanism of a LANNET repeater. |
| INT ethGroup10BTPlus | 1.3.6.1.4.1.81.12.2.1.1.3 | INTEGER | read-write | Value ON of this attribute defines activation of the 10BaseTPlus mode - a LANNET extension of the 10BaseT standard. |
| INT ethGroupIntPortsRedundancy | 1.3.6.1.4.1.81.12.2.1.1.4 | INTEGER | read-write | Value ON of this attribute defines a redundancy (backup) relationship between internal ports 1 and 2 on a LANNET module. |
| INT ethGroupBackboneMode | 1.3.6.1.4.1.81.12.2.1.1.5 | INTEGER | read-write | Value On of this attribute defines Backbone Mode of a sensor. Internal ports are enabled and the information path goes straightly from external port to internal bus, via corresponding internal port. |
| INT ethGroupFOIRLPlusMode | 1.3.6.1.4.1.81.12.2.1.1.6 | INTEGER | read-write | Value On of this attribute defines FOIRL of a sensor. When this attribute has value ON, FOIRL Plus mode is enabled, while value OFF indicates stan- dard FOIRL mode. |
| INT ethGroupWrongPortSelection | 1.3.6.1.4.1.81.12.2.1.1.7 | INTEGER | read-only | A value ON of this attribute warns of incorrect selection of enabled ports on sensors which impose restrictions on this configura- tion (e.g. integrated local bridges.) |
| INT ethGroupBackupBus | 1.3.6.1.4.1.81.12.2.1.1.8 | INTEGER | read-write | Defines the common secondary bus for Ethernet groups with bus redundancy defined at port level. |
| INT ethGroupSingleBusMode | 1.3.6.1.4.1.81.12.2.1.1.9 | INTEGER | read-only | Value 'on of this attribute defines bus-star mode for cards supporting this type of configuration. |
| OID ethGroupSpecificOID | 1.3.6.1.4.1.81.12.2.1.1.10 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| ethPort | 1.3.6.1.4.1.81.12.3 | |||
| ethPortTable | 1.3.6.1.4.1.81.12.3.1 | not-accessible | ||
| ethPortEntry | 1.3.6.1.4.1.81.12.3.1.1 | not-accessible | ||
| INT ethPortGroupId | 1.3.6.1.4.1.81.12.3.1.1.1 | INTEGER | read-only | Id of the group to which the port belongs. |
| INT ethPortId | 1.3.6.1.4.1.81.12.3.1.1.2 | INTEGER | read-only | Unique Id of the port in the ethPortTable. |
| INT ethPortFunctionalStatus | 1.3.6.1.4.1.81.12.3.1.1.3 | INTEGER | read-only | The value of this attribute reflects the functional status of LANNET synchronous ports. Note that it is not mandatory that all ports support all the enumerated states. Here is the minimal set possible states: OK - fully functional port, transmitting and receiving packets. RLD - receive link down condition on the port. TLD - transmit link down condition on the port. LocalJabber - fault condition indicating that the port emitted jabber. RemoteJabber - fault condition indicating that remote jabber was sensed at the port. IllSeq - Fault condition indicating an illegal synchronization sequence at the port. ShortCircuit - short-circuit fault condition detected at the port. PartitionOrLocalJabber - RemoteFaultOrLockLoss - |
| INT ethPortManPart | 1.3.6.1.4.1.81.12.3.1.1.4 | INTEGER | read-write | Setting the value of this attribute to ON activates the manual partition mechanism at the port level. Setting the value of this attribute to OFF cancels the partition mechanism. The segment may reconnect after the reception of 32 packets. Attribute vaild for repeater modules from the LE-10 family. |
| INT ethPortJabber | 1.3.6.1.4.1.81.12.3.1.1.5 | INTEGER | read-only | Value ON of this attribute reflects jabber transmitted to the port by the hardware of a LANNET repeater or transceiver, as a result of collisions detected on the port. Valid for all modules in the LE-10 and LE-15 families. |
| INT ethPortNoAUILoop | 1.3.6.1.4.1.81.12.3.1.1.6 | INTEGER | read-only | Value ON of this attribute indicates that a No AUI Loop fault condition was detected on an AUI repeater port. Valid for LE-10C family of modu- les. |
| INT ethPortMJLP | 1.3.6.1.4.1.81.12.3.1.1.7 | INTEGER | read-only | Value ON of this attribute describes an internal MJLP (MAU Jabber Lockup Protection) error sensed by the internal hardware mechanism of a LANNET repeater. Valid for LE140XTF. |
| INT ethPortFIFO | 1.3.6.1.4.1.81.12.3.1.1.8 | INTEGER | read-only | Value ON of this attribute describes an internal FIFO error sensed by the internal hardware mechanism of a LANNET repeater. Valid for LE140XTF. |
| INT ethPortAutoPartitionState | 1.3.6.1.4.1.81.12.3.1.1.9 | INTEGER | read-only | The AutoPart condition indicates that the port is currently partitioned by the auto-partition protection mechanism. |
| INT ethPortSQETest | 1.3.6.1.4.1.81.12.3.1.1.10 | INTEGER | read-write | Settable attribute which allows activation of SQE test for LANNET integrated transceivers. |
| OCT ethPortLastSourceAddr | 1.3.6.1.4.1.81.12.3.1.1.11 | OCTET STRING | read-only | Ethernet source address of the last readable frame received by this port. |
| INT ethPortUserStatus | 1.3.6.1.4.1.81.12.3.1.1.12 | INTEGER | read-only | Attribute defining the connection of a port to a single Ethernet source or to a multi-source (segment or star). |
| INT ethPortMainBusSelection | 1.3.6.1.4.1.81.12.3.1.1.13 | INTEGER | read-write | On cards with port-level redundancy, defines the main bus for each port instance as selected by user. |
| CTR ethPortTraffic | 1.3.6.1.4.1.81.12.3.1.1.14 | Counter | read-only | Counter for the number of bits received on this port in frames with legal length information. |
| CTR ethPortFramesReceivedOK | 1.3.6.1.4.1.81.12.3.1.1.15 | Counter | read-only | A representation of the total number of frames of legal length that have not been corrupted in transmission. These frames can be encoded and decoded by the commonly available MACs and provide a measure of the network bandwidth being used. The number does not include frames received with frame-too-long, FCS, alignment errors, frames lost due to internal MAC sublayer errors, runts or pygmys. |
| CTR ethPortRunts | 1.3.6.1.4.1.81.12.3.1.1.16 | Counter | read-only | Counter for the number of collision fragments longer than a pygmy and shorter than a legal packet, detected on this port. |
| CTR ethPortPacketErrors | 1.3.6.1.4.1.81.12.3.1.1.17 | Counter | read-only | Counter for the number of frames with errors detected on the port by the LANNET agent hardware. This generic port error comprises too long packets, CRC and alignment errors. |
| OID ethPortSpecificOID | 1.3.6.1.4.1.81.12.3.1.1.18 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| ethIntPort | 1.3.6.1.4.1.81.12.4 | |||
| ethIntPortTable | 1.3.6.1.4.1.81.12.4.1 | not-accessible | ||
| ethIntPortEntry | 1.3.6.1.4.1.81.12.4.1.1 | not-accessible | ||
| INT ethIntPortGroupId | 1.3.6.1.4.1.81.12.4.1.1.1 | INTEGER | read-only | ID of the group to which the internal port belongs. |
| INT ethIntPortId | 1.3.6.1.4.1.81.12.4.1.1.2 | INTEGER | read-only | ID of the internal port in the ethIntPortTable. |
| INT ethIntPortPartition | 1.3.6.1.4.1.81.12.4.1.1.3 | INTEGER | read-only | This condition indicates that the internal port is currently partitioned from the bus by the auto-partition protection mechanism. |
| INT ethIntPortJabber | 1.3.6.1.4.1.81.12.4.1.1.4 | INTEGER | read-only | Value ON of this attribute reflects jabber being transmitted to the bus by the hardware of a LANNET repeater, as a result of collisions detected on the internal bus of the enclosure. This situation is similar to MJLP as defined by the Repeater Management standard. |
| INT ethIntPortBackedUp | 1.3.6.1.4.1.81.12.4.1.1.5 | INTEGER | read-write | Indicates that internal port is part of a redundancy scheme. |
| ethBus | 1.3.6.1.4.1.81.12.5 | |||
| ethBusPerfTable | 1.3.6.1.4.1.81.12.5.1 | not-accessible | ||
| ethBusPerfEntry | 1.3.6.1.4.1.81.12.5.1.1 | not-accessible | ||
| INT ethBusPerfAgId | 1.3.6.1.4.1.81.12.5.1.1.1 | INTEGER | read-only | ID of the agent in the ethBusPerfTable. |
| INT ethBusPerfId | 1.3.6.1.4.1.81.12.5.1.1.2 | INTEGER | read-only | ID of the bus in the ethBusPerfTable. |
| OCT ethBusTrafficBuffer | 1.3.6.1.4.1.81.12.5.1.1.3 | OCTET STRING | read-only | Record of traffic for the last second with a resolution of 100 msec. The traffic is expressed in percents of the maximum Ethernet traffic and each record contains 10 readings, in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ). |
| INT ethBusTrafficThresh | 1.3.6.1.4.1.81.12.5.1.1.4 | INTEGER | read-write | Traffic threshold value. When exceeded, a trap is send to the management console. Expressed in percents of the maximum Ethernet traffic, in the range 1..20, expressed on a log(10) scale. |
| INT ethBusPeakTraffic | 1.3.6.1.4.1.81.12.5.1.1.5 | INTEGER | read-only | Maximal traffic value since last reset of hub or relay. Expressed in per- cents of the maximum Ethernet traffic, in the range 1..20, expressed on log(10) scale. |
| CTR ethBusTotalCollisions | 1.3.6.1.4.1.81.12.5.1.1.6 | Counter | read-only | Counter incremented every time the hub enters a condition caused by simultaneous transmission and detection of external activity on one or more of its ports. |
| CTR ethBusTotalPackets | 1.3.6.1.4.1.81.12.5.1.1.7 | Counter | read-only | Counter for number of packets (good and errors) detected on the Ethernet bus. |
| CTR ethBusTotalErrors | 1.3.6.1.4.1.81.12.5.1.1.8 | Counter | read-only | Counter for number of errors detected on the Ethernet bus. Does not take into account the collisions. |
| INT ethBusTraffic | 1.3.6.1.4.1.81.12.5.1.1.9 | INTEGER | read-only | Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Ethernet traffic in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ). |
| ethBusClockTable | 1.3.6.1.4.1.81.12.5.2 | not-accessible | ||
| ethBusClockEntry | 1.3.6.1.4.1.81.12.5.2.1 | not-accessible | ||
| INT ethBusClockBusId | 1.3.6.1.4.1.81.12.5.2.1.1 | INTEGER | read-only | ID of the bus in the ethBusClockTable. |
| INT ethBusClockId | 1.3.6.1.4.1.81.12.5.2.1.2 | INTEGER | read-only | ID of the clock in the ethBusClockTable. |
| INT ethBusClockTestResult | 1.3.6.1.4.1.81.12.5.2.1.3 | INTEGER | read-only | Values clockFailure and busFailure define the faulty statuses for clock tests. The test is performed by LCL100 module. |
| tok | 1.3.6.1.4.1.81.13 | |||
| tokRing | 1.3.6.1.4.1.81.13.1 | |||
| tokRingTable | 1.3.6.1.4.1.81.13.1.1 | not-accessible | ||
| tokRingEntry | 1.3.6.1.4.1.81.13.1.1.1 | not-accessible | ||
| INT tokRingAgId | 1.3.6.1.4.1.81.13.1.1.1.1 | INTEGER | read-only | ID of the agent to which the ring belongs in the tokRingTable. |
| INT tokRingId | 1.3.6.1.4.1.81.13.1.1.1.2 | INTEGER | read-only | ID of the ring in the tokRingTable. |
| INT tokRingLeftSlot | 1.3.6.1.4.1.81.13.1.1.1.3 | INTEGER | read-only | Slot number of the left-most slot of the ring. |
| INT tokRingRightSlot | 1.3.6.1.4.1.81.13.1.1.1.4 | INTEGER | read-write | Slot number of the right-most slot of the ring. |
| OCT tokRingTrafficBuffer | 1.3.6.1.4.1.81.13.1.1.1.5 | OCTET STRING | read-only | Record of traffic for the last second with a resolution of 100 msec. The traffic is expressed in percents of the maximum effective TR traffic (token messages are excluded) and each record contains 10 readings, in range 1..20 on log(10) scale. |
| INT tokRingTrafficThresh | 1.3.6.1.4.1.81.13.1.1.1.6 | INTEGER | read-write | Traffic threshold value. When exceeded, a trap is send to the management console. Expressed in percents of the maximum effective TR traffic (token messages are excluded) in the range 1..20 on log(10) scale. |
| INT tokRingPeakTraffic | 1.3.6.1.4.1.81.13.1.1.1.7 | INTEGER | read-only | Maximal traffic value since last reset of agent. Expressed in percents of the maximum effective TR traffic (token messages are excluded), in the range 1..20 on log(10) scale. |
| INT tokRingNumberOfStations | 1.3.6.1.4.1.81.13.1.1.1.8 | INTEGER | read-only | Number of Token Ring stations (controllers) detected on the ring. The TR controller of the agent card is included in this count. |
| OCT tokRingConfiguration | 1.3.6.1.4.1.81.13.1.1.1.9 | OCTET STRING | read-only | Configuration attribute describing the list of physical addresses detected on the Token Ring. Coded in internal LANNET application format. |
| INT tokRingBeaconing | 1.3.6.1.4.1.81.13.1.1.1.10 | INTEGER | read-only | This attribute indicates if a beaconing condition is currently detected on the ring. |
| OCT tokRingBeaconingStation | 1.3.6.1.4.1.81.13.1.1.1.11 | OCTET STRING | read-only | The MAC address of the last station which was detected as sending Beaconing MAC frames on the ring. |
| INT tokRingStationsMatch | 1.3.6.1.4.1.81.13.1.1.1.12 | INTEGER | read-only | This attribute indicates matching between the number of stations detected on the ring between the current agent and the next agent on Up Stream sense and the number of connected lobe ports.Used by the port address correlation mechanism. |
| INT tokRingTraffic | 1.3.6.1.4.1.81.13.1.1.1.13 | INTEGER | read-only | Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Ethernet traffic in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ). |
| tokGroup | 1.3.6.1.4.1.81.13.2 | |||
| tokGroupTable | 1.3.6.1.4.1.81.13.2.1 | not-accessible | ||
| tokGroupEntry | 1.3.6.1.4.1.81.13.2.1.1 | not-accessible | ||
| INT tokGroupId | 1.3.6.1.4.1.81.13.2.1.1.1 | INTEGER | read-only | Number of the slot in which the group is installed. |
| INT tokGroupAutoRightLoop | 1.3.6.1.4.1.81.13.2.1.1.2 | INTEGER | read-only | Value ON of this attribute signifies that a hardware loop was automatically created on a Token Ring module which does not sense the existence of another token ring group on the right hand side. |
| INT tokGroupAutoLeftLoop | 1.3.6.1.4.1.81.13.2.1.1.3 | INTEGER | read-only | Value ON of this attribute signifies that a hardware loop was automatically created on a Token Ring module which does not sense the existence of another token ring group on the left hand side. |
| INT tokGroupManRightLoop | 1.3.6.1.4.1.81.13.2.1.1.4 | INTEGER | read-write | Setting this attribute to ON signifies a command to the hardware to create a loop on the Token Ring module which isolates the ring from the right hand side. |
| INT tokGroupManLeftLoop | 1.3.6.1.4.1.81.13.2.1.1.5 | INTEGER | read-write | Setting this attribute to ON signifies a command to the hardware to create a loop on the Token Ring module which isolates the ring from the left hand side. |
| INT tokGroupRightNeighbor | 1.3.6.1.4.1.81.13.2.1.1.6 | INTEGER | read-only | Attribute defining the existence of a neighbor another token ring group on the right hand side of the module. |
| INT tokGroupLeftNeighbor | 1.3.6.1.4.1.81.13.2.1.1.7 | INTEGER | read-only | Attribute defining the existence of a neighbor another token ring group on the left hand side of the module. |
| INT tokGroupIOMode | 1.3.6.1.4.1.81.13.2.1.1.8 | INTEGER | read-write | Attribute defining the I/O mode (single, dual-ring-in, dual-ring-out) Lobe, Internal Repeater or Star) of a module from the the LTR-IO family. |
| INT tokGroupBridgeMode | 1.3.6.1.4.1.81.13.2.1.1.9 | INTEGER | read-write | Attribute describing the operational mode of the bridge. For ITLB the following modes are defined: - Mode A: First channel connected to an external ring (RI,RO connectors) and second channel connected to an internal ring; - Mode B: First channel connected to an external ring by a DTE connector and second channel connected to an internal ring; - Mode C: First channel connected to an internal left ring and second channel connected to an internal right ring. |
| INT tokGroupManLinkLoop | 1.3.6.1.4.1.81.13.2.1.1.10 | INTEGER | read-write | Setting the value of this attribute to ON instructs the hardware of a LANNET Token Ring repeater module to close the loop in the direction of the external connection. |
| INT tokGroupManBusLoop | 1.3.6.1.4.1.81.13.2.1.1.11 | INTEGER | read-write | Setting the value of this attribute to ON instructs the hardware of a LANNET Token Ring repeater module to close the loop in the direction of the internal bus. |
| INT tokGroupAutoLinkLoop | 1.3.6.1.4.1.81.13.2.1.1.12 | INTEGER | read-only | Value ON of this attribute signifies that a hardware loop has been auto- matically closed by the hardwar of the LANNET Token Ring repeater as a result of problems on the external link. |
| INT tokGroupAutoBusLoop | 1.3.6.1.4.1.81.13.2.1.1.13 | INTEGER | read-only | Value ON of this attribute signifies that a hardware loop has been auto- matically closed by the hardware of the LANNET Token Ring repeater as a result of problems on the internal bus. |
| OID tokGroupSpecificOID | 1.3.6.1.4.1.81.13.2.1.1.14 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| tokGroupRingTable | 1.3.6.1.4.1.81.13.2.2 | not-accessible | ||
| tokGroupRingEntry | 1.3.6.1.4.1.81.13.2.2.1 | not-accessible | ||
| INT tokGroupRingGroupId | 1.3.6.1.4.1.81.13.2.2.1.1 | INTEGER | read-only | ID of the group to which the ring belongs. |
| INT tokGroupRingId | 1.3.6.1.4.1.81.13.2.2.1.2 | INTEGER | read-only | ID of the ring. |
| INT tokGroupRingSpeed | 1.3.6.1.4.1.81.13.2.2.1.3 | INTEGER | read-write | Attribute describing the bandwidth of the ring. |
| INT tokGroupRingInserted | 1.3.6.1.4.1.81.13.2.2.1.4 | INTEGER | read-only | Indicates that the bridge interface has inserted itself into the ring. |
| tokPort | 1.3.6.1.4.1.81.13.3 | |||
| tokPortTable | 1.3.6.1.4.1.81.13.3.1 | not-accessible | ||
| tokPortEntry | 1.3.6.1.4.1.81.13.3.1.1 | not-accessible | ||
| INT tokPortGroupId | 1.3.6.1.4.1.81.13.3.1.1.1 | INTEGER | read-only | ID of the group to which the token ring port belongs. |
| INT tokPortId | 1.3.6.1.4.1.81.13.3.1.1.2 | INTEGER | read-only | ID of the port in the tokPortTable. |
| INT tokPortBypass | 1.3.6.1.4.1.81.13.3.1.1.3 | INTEGER | read-write | Setting the value of this attribute to ON causes the by- passing of the TokenRing LANNET port. |
| INT tokPortConnected | 1.3.6.1.4.1.81.13.3.1.1.4 | INTEGER | read-only | Attribute which describes the connection status of a Token Ring port (inclusion of the Token Ring controller in the ring). |
| INT tokPortTCP | 1.3.6.1.4.1.81.13.3.1.1.5 | INTEGER | read-write | Setting the value of this attribute to ON causes the activation of the cable-fault detection mechanism. |
| INT tokPortCableFault | 1.3.6.1.4.1.81.13.3.1.1.6 | INTEGER | read-only | Value ON of this attribute signifies the detection of a cable-fault on this specific Token Ring port. |
| INT tokPortFunctionalStatus | 1.3.6.1.4.1.81.13.3.1.1.7 | INTEGER | read-only | The value of this attribute reflects the functional status of LANNET Token Ring ports. Note that it is not mandatory that a certain port support all the enumerated states. Here is the lest of the possible states: OK - fully functional port, transmitting and receiving packets. RLD - receive link down condition on the port. TLD - transmit link down condition on the port. |
| OCT tokPortLastSourceAddr | 1.3.6.1.4.1.81.13.3.1.1.8 | OCTET STRING | read-only | MAC source address of the last readable frame received by this port. |
| OID tokPortSpecificOID | 1.3.6.1.4.1.81.13.3.1.1.9 | OBJECT IDENTIFIER | read-only | This attribute provides the OID of another group containing additional more specific information regarding this instance. |
| ts | 1.3.6.1.4.1.81.14 | |||
| tsGroup | 1.3.6.1.4.1.81.14.1 | |||
| tsGroupTable | 1.3.6.1.4.1.81.14.1.1 | not-accessible | ||
| tsGroupEntry | 1.3.6.1.4.1.81.14.1.1.1 | not-accessible | ||
| INT tsGroupId | 1.3.6.1.4.1.81.14.1.1.1.1 | INTEGER | read-only | Number of the slot in which the group is installed. |
| INT tsGroupLATStatus | 1.3.6.1.4.1.81.14.1.1.1.2 | INTEGER | read-only | Value ON of this attribute means that LAT protocol is Enabled on the LANNET Ethernet module. |
| INT tsGroupOperationMode | 1.3.6.1.4.1.81.14.1.1.1.3 | INTEGER | read-only | This attribute describes the operation mode of the module in a multiprocessor configuration sensor, as reported by interprocessors communication. |
| ltalk | 1.3.6.1.4.1.81.15 | |||
| ltalkPort | 1.3.6.1.4.1.81.15.1 | |||
| ltalkPortTable | 1.3.6.1.4.1.81.15.1.1 | not-accessible | ||
| ltalkPortEntry | 1.3.6.1.4.1.81.15.1.1.1 | not-accessible | ||
| INT ltalkPortGroupId | 1.3.6.1.4.1.81.15.1.1.1.1 | INTEGER | read-only | Number of the group to which the port belongs. |
| INT ltalkPortId | 1.3.6.1.4.1.81.15.1.1.1.2 | INTEGER | read-only | ID of the port in the ltalkPortTable. |
| INT ltalkPortTest | 1.3.6.1.4.1.81.15.1.1.1.3 | INTEGER | read-write | A value ON of this attribute indicates that a port test should be performed upon the port defined by the attribute instance. |
| INT ltalkPortTestResult | 1.3.6.1.4.1.81.15.1.1.1.4 | INTEGER | read-only | Indicates the result of a port test performed on this port. |
| INT ltalkPortJam | 1.3.6.1.4.1.81.15.1.1.1.5 | INTEGER | read-only | An ON value of this attribute indicates a Jam error on the specific port. |
| cl | 1.3.6.1.4.1.81.16 | |||
| clGroup | 1.3.6.1.4.1.81.16.1 | |||
| clGroupTable | 1.3.6.1.4.1.81.16.1.1 | not-accessible | ||
| clGroupEntry | 1.3.6.1.4.1.81.16.1.1.1 | not-accessible | ||
| INT clGroupId | 1.3.6.1.4.1.81.16.1.1.1.1 | INTEGER | read-only | Number of the slot in which the group is installed. |
| INT clGroupClockRedundancy | 1.3.6.1.4.1.81.16.1.1.1.2 | INTEGER | read-write | Value ON of this attribute defines a redundancy (backup) relationship between the internal and external clocks on the LCL100 module. |
| INT clGroupMainClock | 1.3.6.1.4.1.81.16.1.1.1.3 | INTEGER | read-write | Value of this attribute is an index into clPortTable, and defines the clock that should operate or a main clock in redundancy scheme. Serves as 'Clock selection' switch on the card. |
| INT clGroupTestClocks | 1.3.6.1.4.1.81.16.1.1.1.4 | INTEGER | read-write | A value ON of this attribute indicates that a test should be performed on all clock ports. |
| clPort | 1.3.6.1.4.1.81.16.2 | |||
| clPortTable | 1.3.6.1.4.1.81.16.2.1 | not-accessible | ||
| clPortEntry | 1.3.6.1.4.1.81.16.2.1.1 | not-accessible | ||
| INT clPortGroupId | 1.3.6.1.4.1.81.16.2.1.1.1 | INTEGER | read-only | Number of the group to which the port belongs. |
| INT clPortId | 1.3.6.1.4.1.81.16.2.1.1.2 | INTEGER | read-only | ID of the port in the clPortTable. |
| INT clPortFunctionalStatus | 1.3.6.1.4.1.81.16.2.1.1.3 | INTEGER | read-only | Indicates whether the clock is faulty or not. |
| lntOID | 1.3.6.1.4.1.81.17 | |||
| lBoxOID | 1.3.6.1.4.1.81.17.1 | |||
| lUnknownBoxOID | 1.3.6.1.4.1.81.17.1.1 | |||
| lLET18BoxOID | 1.3.6.1.4.1.81.17.1.2 | |||
| lLET3BoxOID | 1.3.6.1.4.1.81.17.1.3 | |||
| lLET36BoxOID | 1.3.6.1.4.1.81.17.1.4 | |||
| lLET18EBoxOID | 1.3.6.1.4.1.81.17.1.5 | |||
| lLERT40BoxOID | 1.3.6.1.4.1.81.17.1.6 | |||
| lLET10BoxOID | 1.3.6.1.4.1.81.17.1.7 | |||
| lFDX100BoxOID | 1.3.6.1.4.1.81.17.1.8 |
RFC description
Enterprise MIB for LANNET network devices covering Ethernet, Token Ring, terminal servers, and general chassis management.
Start monitoring LANNET modular Ethernet/Token Ring hub chassis with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.