Juniper-PPP-CONF

All MIBs › Juniper-PPP-CONF

Organization: Juniper Networks, Inc.

Last Updated: 2010-02-09

Category: Protocol: PPP, Vendor: Juniper

Description: Juniper Networks conformance statements for Point-to-Point Protocol (PPP) management on Juniper E-series edge routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-PPP-CONF?

Juniper-PPP-CONF is an AGENT-CAPABILITIES conformance module documenting the Point-to-Point Protocol (PPP) management support of the SNMP agent on Juniper E-series edge routers. It declares which object groups and variations of the underlying PPP MIB the agent implements, rather than introducing new manageable data. As with other Juniper *-CONF modules it carries no runtime hardware or software status data on its own; actual PPP session, link, and interface state is exposed by the PPP MIB(s) it references. It depends on the standard or Juniper PPP MIB definitions whose implementation it constrains. It is used by network management tools during MIB compilation and capability discovery for PPP-based broadband edge deployments, since the Juniper-PPP-CONF MIB itself defines no monitorable objects of its own.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-PPP-CONF. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks E-series broadband routers

Monitoring Examples

This module defines no pollable runtime objects itself; it only specifies which PPP MIB groups (such as link and LCP-related tables) are supported by the E-series agent. Management software would reference it to determine object availability before attempting to poll actual PPP session state elsewhere. No direct monitoring scenario applies to this conformance module alone.

Imported Objects

From Juniper-Agents

juniAgents

MODULE-IDENTITY

From SNMPv2-CONF

AGENT-CAPABILITIES

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Description
juniPppAgent	1.3.6.1.4.1.4874.5.2.32	The agent capabilities definitions for the point-to-point protocol (PPP) component of the SNMP agent in the Juniper E-series family of products.
juniPppAgentV1	1.3.6.1.4.1.4874.5.2.32.1	The MIBs supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when the multilink capabilities were separated out.
juniPppGeneralAgent	1.3.6.1.4.1.4874.5.2.32.2	The registration group of agent capabilities for the general functionality of the PPP application which provides management support for basic (non-multi-link) PPP interfaces via SNMP.
juniPppGeneralAgentV1	1.3.6.1.4.1.4874.5.2.32.2.1	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe. These capabilities became obsolete when new LCP and IP objects were added to the Juniper-PPP-MIB.
juniPppGeneralAgentV2	1.3.6.1.4.1.4874.5.2.32.2.2	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe. These capabilities became obsolete when new LCP objects were added to the Juniper-PPP-MIB.
juniPppGeneralAgentV3	1.3.6.1.4.1.4874.5.2.32.2.3	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe. These capabilities became obsolete when IPv6 support was added.
juniPppGeneralAgentV4	1.3.6.1.4.1.4874.5.2.32.2.4	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe. These capabilities became obsolete when new objects were added.
juniPppGeneralAgentV5	1.3.6.1.4.1.4874.5.2.32.2.5	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe. These capabilities became obsolete when new objects were added.
juniPppGeneralAgentV6	1.3.6.1.4.1.4874.5.2.32.2.6	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe. These capabilities became obsolete when new objects were added.
juniPppGeneralAgentV7	1.3.6.1.4.1.4874.5.2.32.2.7	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe.
juniPppGeneralAgentV8	1.3.6.1.4.1.4874.5.2.32.2.8	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe.These capabilities became obsolete when new objects were added.
juniPppGeneralAgentV9	1.3.6.1.4.1.4874.5.2.32.2.9	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe.
juniPppMultiLinkAgent	1.3.6.1.4.1.4874.5.2.32.3	The registration group of agent capabilities for the multi-link functionality of the PPP application which provides management support for multi-link PPP interfaces via SNMP.
juniPppMultiLinkAgentV1	1.3.6.1.4.1.4874.5.2.32.3.1	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when new multi-link objects were added to the Juniper-PPP-MIB.
juniPppMultiLinkAgentV2	1.3.6.1.4.1.4874.5.2.32.3.2	The MIBs supported by the SNMP agent for the basic PPP application in JUNOSe. These capabilities became obsolete when new multi-link objects were added to the Juniper-PPP-MIB
juniPppMultiLinkAgentV3	1.3.6.1.4.1.4874.5.2.32.3.3	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when new multi-link objects were added to the Juniper-PPP-MIB
juniPppMultiLinkAgentV4	1.3.6.1.4.1.4874.5.2.32.3.4	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when IPv6 support was added.
juniPppMultiLinkAgentV5	1.3.6.1.4.1.4874.5.2.32.3.5	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when new multi-link objects were added to the Juniper-PPP-MIB.
juniPppMultiLinkAgentV6	1.3.6.1.4.1.4874.5.2.32.3.6	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when new multi-link objects were added to the Juniper-PPP-MIB.
juniPppMultiLinkAgentV7	1.3.6.1.4.1.4874.5.2.32.3.7	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when new multi-link objects were added to the Juniper-PPP-MIB.
juniPppMultiLinkAgentV8	1.3.6.1.4.1.4874.5.2.32.3.8	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when new multi-link objects were added to the Juniper-PPP-MIB.
juniPppMultiLinkAgentV9	1.3.6.1.4.1.4874.5.2.32.3.9	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe. These capabilities became obsolete when new multi-link objects were added to the Juniper-PPP-MIB.
juniPppMultiLinkAgentV10	1.3.6.1.4.1.4874.5.2.32.3.10	The MIB groups supported by the SNMP agent for the PPP application in JUNOSe.

RFC description

Juniper vendor-private MIB for Point-to-Point Protocol (PPP) configuration and management on Juniper devices.

Start monitoring Juniper Networks E-series broadband router (agent capabilities, PPP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-PPP-CONF

What Is Juniper-PPP-CONF?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description