Juniper-FRAME-RELAY-MIB

All MIBs › Juniper-FRAME-RELAY-MIB

Organization: Juniper Networks, Inc.

Last Updated: 2002-12-13

Category: Domain: WAN, Frame Relay, Protocol: Frame Relay, Vendor: Juniper

Description: Provides managed objects for Frame Relay PVC monitoring, traffic statistics, and LMI status on Juniper Networks E-series routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-FRAME-RELAY-MIB?

Juniper-FRAME-RELAY-MIB is a Juniper Networks enterprise MIB providing managed objects for Frame Relay interface configuration, PVC monitoring, and Local Management Interface (LMI/DLCMI) status on Juniper E-series routers. It exposes DLCMI state, addressing, polling and enquiry intervals, error thresholds, and monitored-event settings per Frame Relay interface, alongside interface-layer objects for the Frame Relay sublayer. This is directly useful for monitoring the operational health of Frame Relay WAN links: an admin can check DLCMI state to see if the LMI protocol is up between router and Frame Relay switch, and error thresholds/monitored events to catch a degrading or flapping link before it fully fails. It extends the standard Frame Relay DTE MIB concepts (DLCMI) in a Juniper-specific way, and depends on the base IF-MIB for interface indexing. It is deployed on Juniper E-series routers used as Frame Relay access equipment in legacy WAN deployments. Engineers can download the Juniper-FRAME-RELAY-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-FRAME-RELAY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks E-series router

Monitoring Examples

An operator can poll juniFrDlcmiTable/juniFrDlcmiEntry indexed by juniFrDlcmiIfIndex to read juniFrDlcmiState, confirming whether the LMI session to the Frame Relay network is active or down. Watching juniFrDlcmiErrorThreshold against actual error counts, along with juniFrDlcmiMonitoredEvents, helps detect a flapping or unreliable Frame Relay circuit. juniFrDlcmiMaxSupportedVCs indicates the PVC capacity of the interface, useful when planning additional virtual circuits.

What Can Be Monitored

DLCMI/LMI state
polling and enquiry intervals
error threshold and monitored events
maximum supported virtual circuits
DLCMI address configuration

Imported Objects

From FRAME-RELAY-DTE-MIB

DLCI

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From Juniper-MIBs

juniMibs

MODULE-IDENTITY

From Juniper-TC

JuniNextIfIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TimeStamp

How to Use in IPNetwork Monitor

Example using juniFrDlcmiStatsDteEnquiries OID:

Select a Juniper Networks E-series router (Frame Relay PVC/LMI status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type juniFrDlcmiStatsDteEnquiries into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the number of Status Enquiries sent (as DTE). On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
juniFrameRelayMIB	1.3.6.1.4.1.4874.2.2.10			The Frame Relay MIB for the Juniper Networks enterprise.
I32 juniFrCircuitCommittedBurst	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.12	Integer32	read-create	This variable indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval. A value of zero (the default) indicates no commitment.
TIM juniFrCircuitCreationTime	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.10	TimeStamp	read-only	The value of sysUpTime when the virtual circuit was created, whether by the Data Link Connection Management Interface or by a SetRequest.
C32 juniFrCircuitDiscards	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.17	Counter32	read-only	The number of inbound frames dropped because of format errors, or because the VC is inactive.
DLC juniFrCircuitDlci	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.2	DLCI	not-accessible	The Data Link Connection Identifier for this virtual circuit.
juniFrCircuitEntry	1.3.6.1.4.1.4874.2.2.10.1.1.4.1		not-accessible	The information regarding a single Data Link Connection. Discontinuities in the counters contained in this table are indicated by the value in juniFrCircuitCreationTime.
I32 juniFrCircuitExcessBurst	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.13	Integer32	read-create	This variable indicates the maximum amount of uncommitted data bits that the network will attempt to deliver over the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ifSpeed.
NUM juniFrCircuitIfIndex	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.1	InterfaceIndex	not-accessible	The ifIndex Value of the ifEntry this virtual circuit is layered onto.
TIM juniFrCircuitLastTimeChange	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.11	TimeStamp	read-only	The value of sysUpTime when last there was a change in the virtual circuit state
NUM juniFrCircuitLogicalIfIndex	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.20	InterfaceIndex	read-create	Normally the same value as frDlcmiIfIndex, but different when an implementation associates a virtual ifEntry with a DLC or set of DLCs in order to associate higher layer objects such as the ipAddrEntry with a subset of the virtual circuits on a Frame Relay interface. The type of such ifEntries is defined by the higher layer object; for example, if PPP/Frame Relay is implemented, the ifType of this ifEntry would be PPP. If it is not so defined, as would be the case with an ipAddrEntry, it should be of type Other.
INT juniFrCircuitMulticast	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.15	INTEGER	read-create	This indicates whether this VC is used as a unicast VC (i.e. not multicast) or the type of multicast service subscribed to.
C32 juniFrCircuitReceivedBECNs	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.5	Counter32	read-only	Number of frames received from the network indicating backward congestion since the virtual circuit was created. This occurs when the remote DTE sets the BECN flag, or when a switch in the network receives the frame from a trunk whose transmission queue is congested.
C32 juniFrCircuitReceivedDEs	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.18	Counter32	read-only	Number of frames received from the network indicating that they were eligible for discard since the virtual circuit was created. This occurs when the remote DTE sets the DE flag, or when in remote DTE's switch detects that the frame was received as Excess Burst data.
C32 juniFrCircuitReceivedFECNs	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.4	Counter32	read-only	Number of frames received from the network indicating forward congestion since the virtual circuit was created. This occurs when the remote DTE sets the FECN flag, or when a switch in the network enqueues the frame to a trunk whose transmission queue is congested.
C32 juniFrCircuitReceivedFrames	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.8	Counter32	read-only	Number of frames received over this virtual circuit since it was created.
C32 juniFrCircuitReceivedOctets	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.9	Counter32	read-only	Number of octets received over this virtual circuit since it was created. Octets counted include the full frame relay header, but do not include the flag characters or the CRC.
ROW juniFrCircuitRowStatus	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.21	RowStatus	read-create	This object is used to create a new row or modify or destroy an existing row in the manner described in the definition of the RowStatus textual convention. Writable objects in the table may be written in any RowStatus state.
C32 juniFrCircuitSentBECNs	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.23	Counter32	read-only	Number of frames sent to the network indicating backward congestion since the virtual circuit was created. This occurs when the remote DTE sets the BECN flag, or when a switch in the network receives the frame from a trunk whose transmission queue is congested.
C32 juniFrCircuitSentDEs	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.19	Counter32	read-only	Number of frames sent to the network indicating that they were eligible for discard since the virtual circuit was created. This occurs when the local DTE sets the DE flag, indicating that during Network congestion situations those frames should be discarded in preference of other frames sent without the DE bit set.
C32 juniFrCircuitSentFECNs	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.22	Counter32	read-only	Number of frames sent to the network indicating forward congestion since the virtual circuit was created. This occurs when the remote DTE sets the FECN flag, or when a switch in the network enqueues the frame to a trunk whose transmission queue is congested.
C32 juniFrCircuitSentFrames	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.6	Counter32	read-only	The number of frames sent from this virtual circuit since it was created.
C32 juniFrCircuitSentOctets	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.7	Counter32	read-only	The number of octets sent from this virtual circuit since it was created. Octets counted are the full frame relay header and the payload, but do not include the flag characters or CRC.
INT juniFrCircuitState	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.3	INTEGER	read-create	Indicates whether the particular virtual circuit is operational. In the absence of a Data Link Connection Management Interface, virtual circuit entries (rows) may be created by setting virtual circuit state to 'active', or deleted by changing Circuit state to 'invalid'. Whether or not the row actually disappears is left to the implementation, so this object may actually read as 'invalid' for some arbitrary length of time. It is also legal to set the state of a virtual circuit to 'inactive' to temporarily disable a given circuit. The use of 'invalid' is deprecated in this SNMP Version 2 MIB, in favor of juniFrCircuitRowStatus.
juniFrCircuitTable	1.3.6.1.4.1.4874.2.2.10.1.1.4		not-accessible	A table containing information about specific Data Link Connections (DLC) or virtual circuits. This table mirrors the structure of FRAME-RELAY-DTE-MIB.frCircuitTable, for the purpose of enumerating circuits on both DTE and DCE Frame Relay interfaces.
I32 juniFrCircuitThroughput	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.14	Integer32	read-create	Throughput is the average number of 'Frame Relay Information Field' bits transferred per second across a user network interface in one direction, measured over the measurement interval. If the configured committed burst rate and throughput are both non-zero, the measurement interval, T, is T = juniFrCircuitCommittedBurst / juniFrCircuitThroughput. If the configured committed burst rate and throughput are both zero, the measurement interval, T, is T = juniFrCircuitExcessBurst / ifSpeed A value of zero (the default) for throughput indicates no commitment.
INT juniFrCircuitType	1.3.6.1.4.1.4874.2.2.10.1.1.4.1.16	INTEGER	read-only	Indication of whether the VC was manually created (static), or dynamically created (dynamic) via the data link control management interface.
juniFrCompliance	1.3.6.1.4.1.4874.2.2.10.4.1.1			Obsolete compliance statement for entities that implement the Juniper Frame Relay MIB. This statement became obsolete when multi-link frame relay support was added.
juniFrCompliance2	1.3.6.1.4.1.4874.2.2.10.4.1.2			The compliance statement for entities that implement the Juniper Frame Relay MIB.
juniFrCompliances	1.3.6.1.4.1.4874.2.2.10.4.1
juniFrConformance	1.3.6.1.4.1.4874.2.2.10.4
INT juniFrDlcmiAddress	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.3	INTEGER	read-create	This variable states which address format is in use on the Frame Relay interface.
INT juniFrDlcmiAddressLen	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.4	INTEGER	read-create	This variable states the address length in octets. In the case of Q922 format, the length indicates the entire length of the address including the control portion.
I32 juniFrDlcmiDceErrorThreshold	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.16	Integer32	read-create	The minimum number of errors that must be observed within the number of events specified by juniFrDlcmiDceMonitoredEvents, to declare the interface down. 'error' is lack of receipt of a Status Enquiry within the interval specified by juniFrDlcmiDcePollingInterval (T392). Pertains to DCE/NNI operation only. This parameter can be reconfigured only when the Frame Relay interface is acting as a DCE or NNI.
I32 juniFrDlcmiDceMonitoredEvents	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.17	Integer32	read-create	The number of DCE polling intervals over which accumulated errors are counted against the threshold specified in juniFrDlcmiDceErrorThreshold. If, within this number of events, the number of errors equals or exceeds the threshold, the interface is declared down. The 'DCE polling interval' is specified by juniFrDlcmiDcePollingInterval. Pertains to DCE/NNI operation only. This parameter can be reconfigured only when the Frame Relay interface is acting as a DCE or NNI.
I32 juniFrDlcmiDcePollingInterval	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.15	Integer32	read-create	The number of seconds within which a DCE expects to receive a Status Enquiry from the DTE. This value corresponds to the T392 timer. Pertains to DCE/NNI operation only. This parameter can be reconfigured only when the Frame Relay interface is acting as a DCE or NNI.
juniFrDlcmiEntry	1.3.6.1.4.1.4874.2.2.10.1.1.2.1		not-accessible	The Parameters for a particular Data Link Connection Management Interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable, and juniFrDlcmiStatsTable. Creating/deleting user-side (DTE) entries in this table also causes coresponding entries to be created/deleted in FRAME-RELAY-DTE-MIB.frDlcmiTable. The organization and definitions of objects in this table are intentionally aligned closely to those in FRAME-RELAY-DTE-MIB.
I32 juniFrDlcmiErrorThreshold	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.7	Integer32	read-create	The minimum number of errors that must be observed within the number of events specified by juniFrDlcmiMonitoredEvents, to declare the interface down. 'error' is lack of receipt of a Status, in response to an issued Status Enquiry, within the Polling Interval (T391). Pertains to DTE/NNI operation only. This parameter can be reconfigured only when the Frame Relay interface is acting as a DTE or NNI.
I32 juniFrDlcmiFullEnquiryInterval	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.6	Integer32	read-create	Number of status enquiry intervals that pass before issuance of a full status enquiry message. Pertains to DTE/NNI operation only. This parameter can be reconfigured only when the Frame Relay interface is acting as a DTE or NNI.
NUM juniFrDlcmiIfIndex	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.1	InterfaceIndex	read-only	The ifIndex value of the corresponding ifEntry.
NUM juniFrDlcmiLowerIfIndex	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.13	InterfaceIndexOrZero	read-create	The ifIndex of an interface over which this Frame Relay interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation. In case of multilink frame relay support, it will be multilink frame relay interface's ifIndex.
DLC juniFrDlcmiMaxSupportedVCs	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.9	DLCI	read-create	The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. In response to a SET, if a value less than zero or higher than the agent's maximal capability is configured, the agent should respond badValue.
I32 juniFrDlcmiMonitoredEvents	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.8	Integer32	read-create	The number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station receives 'ErrorThreshold' number of errors, the interface is marked as down. 'status polling interval' is specified by juniFrDlcmiPollingInterval. Pertains to DTE/NNI operation only. This parameter can be reconfigured only when the Frame Relay interface is acting as a DTE or NNI.
INT juniFrDlcmiMulticast	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.10	INTEGER	read-create	This indicates whether the Frame Relay interface is using a multicast service.
JUN juniFrDlcmiMultilinkFrBundleName	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.18	JuniFrMlFrBundleName	read-create	This represents multilink frame relay bundle name. This object must be configured to associate the bundle name to the frame relay major interface to support the multilink frame relay encapsulation. For non-multilink frame relay, bundle name configuration is not valid and will be ignored.
I32 juniFrDlcmiPollingInterval	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.5	Integer32	read-create	This is the number of seconds between successive status enquiry messages sent by the DTE. Pertains to DTE/NNI operation only. This parameter can be reconfigured only when the Frame Relay interface is acting as a DTE or NNI.
INT juniFrDlcmiRole	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.14	INTEGER	read-create	Specifies the role this interface assumes with respect to the remote end. When acting as a DTE, the following objects are not relevant: juniFrDlcmiDcePollingInterval juniFrDlcmiDceErrorThreshold juniFrDlcmiDceMonitoredEvents When acting as a DCE, the following objects are not relevant: juniFrDlcmiPollingInterval juniFrDlcmiFullEnquiryInterval juniFrDlcmiErrorThreshold juniFrDlcmiMonitoredEvents
ROW juniFrDlcmiRowStatus	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.12	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniFrDlcmiRowStatus juniFrDlcmiState juniFrDlcmiMaxSupportedVCs juniFrDlcmiLowerIfIndex juniFrDlcmiRole juniFrDlcmiMultilinkFrBundleName (Only for multilink frame relay) In addition, when creating an entry the following conditions must hold: A value for juniFrDlcmiIndex must have been determined previously, by reading juniFrNextIfIndex. The interface identified by juniFrDlcmiLowerIfIndex must exist, and must be an interface type that permits layering of Frame Relay above it. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table. If juniFrDlcmiRole is dte(0), a corresponding entry is created/deleted in frDlcmiTable.
INT juniFrDlcmiState	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.2	INTEGER	read-create	This variable states which Data Link Connection Management scheme is active (and by implication, what DLCI it uses) on the Frame Relay interface.
C32 juniFrDlcmiStatsDceAsyncUpdates	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.13	Counter32	read-only	Number of Asynchronous Updates sent (as DCE).
C32 juniFrDlcmiStatsDceEnquiries	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.9	Counter32	read-only	Number of Status Enquiries received (as DCE.)
C32 juniFrDlcmiStatsDceEnquiryResponses	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.11	Counter32	read-only	Number of Status Enquiry responses sent (as DCE).
C32 juniFrDlcmiStatsDceFullEnquiries	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.10	Counter32	read-only	Number of Full Enquiries received (as DCE).
C32 juniFrDlcmiStatsDceFullEnquiryResponses	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.12	Counter32	read-only	Number of Full Enquiry responses sent (as DCE).
C32 juniFrDlcmiStatsDceLossOfSequences	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.15	Counter32	read-only	Number of times a discontinuity in sequence numbering of received messages was detected (as DCE).
C32 juniFrDlcmiStatsDceNoResponseTimeouts	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.16	Counter32	read-only	Number of timer expirations awaiting a Status Enquiry (as DCE).
C32 juniFrDlcmiStatsDceUnknownRxMessages	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.14	Counter32	read-only	Number of unknown messages received (as DCE).
TIK juniFrDlcmiStatsDiscontinuityTime	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.17	TimeTicks	read-only	Value of sysUpTime at the most recent event that caused a discontinuity in the monotonic operation of any of the counters in this entry. Such disruption might be caused by: Hardware insertion/removal. Reconfiguration of juniFrDlcmiState. Reconfiguration of juniFrDlcmiRole. Conclusions can be drawn from successive polls of an entry's counters only if the value of this object, simultaneously retrieved in those polls, remains unchanged.
C32 juniFrDlcmiStatsDteAsyncUpdates	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.5	Counter32	read-only	Number of Asynchronous Updates received (as DTE).
C32 juniFrDlcmiStatsDteEnquiriesEx	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.1	Counter32	read-only	Number of Status Enquiries sent (as DTE).
C32 juniFrDlcmiStatsDteEnquiryResponses	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.3	Counter32	read-only	Number of Status Enquiry responses received (as DTE).
C32 juniFrDlcmiStatsDteFullEnquiries	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.2	Counter32	read-only	Number of Full Enquiries sent (as DTE).
C32 juniFrDlcmiStatsDteFullEnquiryResponses	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.4	Counter32	read-only	Number of Full Enquiry responses received (as DTE).
C32 juniFrDlcmiStatsDteLossOfSequences	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.7	Counter32	read-only	Number of times a discontinuity in sequence numbering of received messages was detected (as DTE).
C32 juniFrDlcmiStatsDteNoResponseTimeouts	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.8	Counter32	read-only	Number of timer expirations awaiting a Status message (as DTE).
C32 juniFrDlcmiStatsDteUnknownRxMessages	1.3.6.1.4.1.4874.2.2.10.1.1.3.1.6	Counter32	read-only	Number of unknown messages received (as DTE).
juniFrDlcmiStatsEntry	1.3.6.1.4.1.4874.2.2.10.1.1.3.1		not-accessible	The statistics for a particular Data Link Connection Management Interface. Statistics are not relevant while the juniFrDlcmiState has the value 'noLmiConfigured'. The DTE statistics are relevant when the corresponding juniFrDlcmiRole is DTE. The DTE statistics are relevant when the corresponding juniFrDlcmiRole is DCE.
juniFrDlcmiStatsTable	1.3.6.1.4.1.4874.2.2.10.1.1.3		not-accessible	The statistics for the Data Link Connection Management Interface for the frame relay service on this interface.
INT juniFrDlcmiStatus	1.3.6.1.4.1.4874.2.2.10.1.1.2.1.11	INTEGER	read-only	This indicates the status of the Frame Relay interface as determined by the performance of the DLCMI. If no DLCMI is running, the Frame Relay interface will stay in the running state indefinitely.
juniFrDlcmiTable	1.3.6.1.4.1.4874.2.2.10.1.1.2		not-accessible	The Parameters for the Data Link Connection Management Interface for the frame relay service on this interface. This table represents a superset of functionality specified in the FRAME-RELAY-DTE-MIB. In particular, it adds attributes that permit the interface to operate as a network-side (DCE) interface.
juniFrGroup	1.3.6.1.4.1.4874.2.2.10.4.2.1			Obsolete collection of objects providing management of Frame Relay interfaces in a Juniper product. This group became obsolete when multi-link frame relay support was added.
juniFrGroup2	1.3.6.1.4.1.4874.2.2.10.4.2.3			A collection of objects providing management of Frame Relay interfaces in a Juniper product.
juniFrGroups	1.3.6.1.4.1.4874.2.2.10.4.2
juniFrIfLayer	1.3.6.1.4.1.4874.2.2.10.1.1
juniFrMlFr	1.3.6.1.4.1.4874.2.2.10.1.3
NUM juniFrMlFrBindLinkIfIndex	1.3.6.1.4.1.4874.2.2.10.1.3.5.1.2	InterfaceIndex	not-accessible	The ifIndex of a FR link interface bound by the FR major interface defined by juniFrMlFrBindMajorIfIndex.
NUM juniFrMlFrBindMajorIfIndex	1.3.6.1.4.1.4874.2.2.10.1.3.5.1.1	InterfaceIndex	not-accessible	The ifIndex of the FR major interface associated with multilink.
ROW juniFrMlFrBindRowStatus	1.3.6.1.4.1.4874.2.2.10.1.3.5.1.3	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniFrMlFrBindRowStatus In addition, when creating an entry the following conditions must hold: The interfaces identified by juniFrMlFrBindNetworkIfIndex and juniFrMlFrBindLinkIfIndex must be created in the juniFrMlFrMajorConfigTable and juniFrMlFrLinkConfigTable respectively. A MLFR bundle must be associated with the juniFrMlFrMajorIfIndex and exist in the juniFrMibFrBundleTable. A corresponding entry in ifStackTable is created/destroyed as a result of creating/destroying an entry in this table. Note: This table is read-only table for now. To add links to bundle make use of juniFrMlFrMajorConfigTable.
juniFrMlFrBundleEntry	1.3.6.1.4.1.4874.2.2.10.1.3.1.1		not-accessible	Each entry describes the characteristics of a Multilink bundle.
JUN juniFrMlFrBundleName	1.3.6.1.4.1.4874.2.2.10.1.3.1.1.1	JuniFrMlFrBundleName	not-accessible	The administrative name of the multilink bundle associated with this Frame Relay major interface.
ROW juniFrMlFrBundleRowStatus	1.3.6.1.4.1.4874.2.2.10.1.3.1.1.2	RowStatus	read-create	The rowStatus for this entry. The following sets are supported: createAndGo(4), destroy(6) The following values can be read from this object: active(1)
juniFrMlFrBundleTable	1.3.6.1.4.1.4874.2.2.10.1.3.1		not-accessible	This table contains entries for MLFR bundles present in the system.
juniFrMlFrGroup	1.3.6.1.4.1.4874.2.2.10.4.2.4			A collection of objects providing management of Multilink Frame Relay in a Juniper product.
juniFrMlFrLinkBindEntry	1.3.6.1.4.1.4874.2.2.10.1.3.5.1		not-accessible	Each entry describes the FR link interface to FR major interface bindingsi associated with multilink bundles.
juniFrMlFrLinkBindTable	1.3.6.1.4.1.4874.2.2.10.1.3.5		not-accessible	This table contains entries for FR Link interfaces to FR major interfaces bindings associated with multilink bundles.
juniFrMlFrLinkConfigEntry	1.3.6.1.4.1.4874.2.2.10.1.3.3.1		not-accessible	Each entry describes the characteristics of FR link interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
NUM juniFrMlFrLinkConfigIfIndex	1.3.6.1.4.1.4874.2.2.10.1.3.3.1.1	InterfaceIndex	not-accessible	The ifIndex of the FR link interface. When creating entries in this table, suitable values for this object are determined by reading juniFrMlFrNextLinkIfIndex.
NUM juniFrMlFrLinkConfigLowerIfIndex	1.3.6.1.4.1.4874.2.2.10.1.3.3.1.2	InterfaceIndexOrZero	read-create	The ifIndex of an interface over which this FR link interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a non-zero value be configured at entry creation.
ROW juniFrMlFrLinkConfigRowStatus	1.3.6.1.4.1.4874.2.2.10.1.3.3.1.3	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniFrMlFrLinkConfigRowStatus juniFrMlFrLinkConfigLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniFrMlFrLinkConfigIfIndex must have been determined previously, by reading juniFrMlFrNextIfIndex. The interface identified by juniFrMlFrLinkConfigLowerIfIndex must exist. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
juniFrMlFrLinkConfigTable	1.3.6.1.4.1.4874.2.2.10.1.3.3		not-accessible	This table contains entries for FR link interfaces present in the system to be added to the multilink bundles.
JUN juniFrMlFrMajorBundleName	1.3.6.1.4.1.4874.2.2.10.1.3.4.1.3	JuniFrMlFrBundleName	read-create	The MLFR bundle name administratively assigned.
juniFrMlFrMajorConfigEntry	1.3.6.1.4.1.4874.2.2.10.1.3.4.1		not-accessible	Each entry describes the characteristics of FR major interface which have association with the MLFR bundles. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
NUM juniFrMlFrMajorConfigIfIndex	1.3.6.1.4.1.4874.2.2.10.1.3.4.1.1	InterfaceIndex	not-accessible	The ifIndex of the FR Major interface. When creating entries in this table, suitable values for this object are determined by reading already created FR Major interface values. Each multilink bundle will be associated with one FR major interface. This association will be done at the creation of FR major interface (juniFrDlcmiTable) specifying its lower interfce binding as FR link ifIndex(juniFrMlFrLinkConfigTable) and the multilink bundle name.
NUM juniFrMlFrMajorConfigLowerIfIndex	1.3.6.1.4.1.4874.2.2.10.1.3.4.1.2	InterfaceIndex	read-create	The ifIndex of a FR link interface over which this FR Major interface is to be layered. On sets, the value of this object must equal on of the previously created FR link interfaces created in the juniFrMlFrLinkConfigTable. On gets, the value of this object is the lexicographically least FR link interface in a potential bundle of FR link interfaces.
juniFrMlFrMajorConfigTable	1.3.6.1.4.1.4874.2.2.10.1.3.4		not-accessible	This table contains entries for FR major interfaces present in the system which are associated with multilink bundles.
ROW juniFrMlFrMajorRowStatus	1.3.6.1.4.1.4874.2.2.10.1.3.4.1.4	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniFrMlFrMajorConfigLowerIfIndex juniFrMlFrMajorBundleName juniFrMlFrMajorConfigRowStatus In addition, when creating an entry the following conditions must hold: The interface identified by juniFrMlFrMajorConfigIndex must exist by a creation request to the juniFrDlcmiTable. The interface identified by juniFrMlFrMajorConfigLowerIfIndex must exist by a creation request to the juniFrMlFrLinkConfigTable. The bundleName specified in juniFrMlFrMajorBundleName must have been created first in the juniFrMlFrBundleTable. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
JUN juniFrMlFrNextLinkIfIndex	1.3.6.1.4.1.4874.2.2.10.1.3.2	JuniNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in juniFrMlFrLinkConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
JUN juniFrNextIfIndex	1.3.6.1.4.1.4874.2.2.10.1.1.1	JuniNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in juniFrDlcmiTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
juniFrObjects	1.3.6.1.4.1.4874.2.2.10.1
DLC juniFrSubIfCktDlci	1.3.6.1.4.1.4874.2.2.10.1.2.3.1.1	DLCI	not-accessible	The DLCI of the Frame Relay circuit used by this subinterface.
juniFrSubIfCktEntry	1.3.6.1.4.1.4874.2.2.10.1.2.3.1		not-accessible	Each entry describes the characteristics of a Frame Relay Subinterface circuit.
ROW juniFrSubIfCktRowStatus	1.3.6.1.4.1.4874.2.2.10.1.2.3.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniFrSubIfCktRowStatus
juniFrSubIfCktTable	1.3.6.1.4.1.4874.2.2.10.1.2.3		not-accessible	This table contains entries for Frame Relay circuits configured on Frame Relay Subinterfaces present in the system. An implementation may constrain the number of circuits permitted to be configured per Frame Relay Subinterface; in particular, an implementation may restrict each Frame Relay Subinterface to have a single circuit. Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
juniFrSubIfEntry	1.3.6.1.4.1.4874.2.2.10.1.2.2.1		not-accessible	Each entry describes the characteristics of a Frame Relay Subinterface. Creating/deleting entries in this table causes corresponding entries for be created /deleted in ifTable/ifXTable/juniIfTable.
juniFrSubIfGroup	1.3.6.1.4.1.4874.2.2.10.4.2.2			A collection of objects providing management of Frame Relay subinterfaces in a Juniper product.
I32 juniFrSubIfId	1.3.6.1.4.1.4874.2.2.10.1.2.2.1.4	Integer32	read-create	An integer identifier for the Frame Relay subinterface, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among subinterfaces configured on the same underlying Frame Relay interface. If this object is not configured, or is configured with a value of -1, a nonzero value will be allocated internally and can be retrieved from this object after table entry creation has succeeded. A value of zero for this object is reserved for future use.
NUM juniFrSubIfIndex	1.3.6.1.4.1.4874.2.2.10.1.2.2.1.1	InterfaceIndex	not-accessible	The ifIndex of the Frame Relay Subinterface. When creating entries in this table, suitable values for this object are determined by reading juniFrSubNextIfIndex.
juniFrSubIfLayer	1.3.6.1.4.1.4874.2.2.10.1.2
NUM juniFrSubIfLowerIfIndex	1.3.6.1.4.1.4874.2.2.10.1.2.2.1.3	InterfaceIndexOrZero	read-create	The ifIndex of a Frame Relay interface over which this Frame Relay Subinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
JUN juniFrSubIfNextIfIndex	1.3.6.1.4.1.4874.2.2.10.1.2.1	JuniNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in juniFrSubIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
ROW juniFrSubIfRowStatus	1.3.6.1.4.1.4874.2.2.10.1.2.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniFrSubIfRowStatus juniFrSubIfLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniFrSubIfIndex must have been determined previously, by reading juniFrSubIfNextIfIndex. The interface identified by juniFrSubIfLowerIfIndex must exist, and must be a Frame Relay interface. A positive value configured for juniFrSubIfId must not already be assigned to another subinterface layered onto the same underlying Frame Relay interface. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
juniFrSubIfTable	1.3.6.1.4.1.4874.2.2.10.1.2.2		not-accessible	This table contains entries for Frame Relay Subinterfaces present in the system.

RFC description

Juniper Networks frame relay interface management including DLCI configuration and multi-link FR support.

Start monitoring Juniper Networks E-series router (Frame Relay PVC/LMI status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-FRAME-RELAY-MIB