All MIBs › Juniper-MPLS-MIB
Organization: Juniper Networks, Inc.
Last Updated: 2004-04-22
Category: Protocol: MPLS, Vendor: Juniper
Description: Juniper Networks MIB for managing and monitoring MPLS label-switched paths and forwarding information on Juniper E-series routers.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Juniper-MPLS-MIB?
Juniper-MPLS-MIB is a Juniper Networks enterprise MIB for configuring and managing Multi-Protocol Label Switching (MPLS) on JUNOSe-based E-series routers. It exposes global MPLS switch settings, per-interface MPLS configuration, tunnel and tunnel-profile parameters, and explicit-path definitions used to build label-switched paths (LSPs). It is heavily used for monitoring MPLS control-plane software health: label range allocation, LSP setup retry counts and intervals under no-route conditions, and LDP session retry behavior all reveal whether the router's MPLS signaling software is successfully establishing and maintaining paths, or is stuck retrying due to reachability or protocol problems. It is a proprietary Juniper module rather than a direct extension of the standard IETF MPLS-LSR/MPLS-TE MIBs, though it covers conceptually similar ground. It is typically deployed on Juniper E-series edge/service-provider routers running MPLS-based VPN or traffic-engineering services. Engineers can download the Juniper-MPLS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-MPLS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Juniper E-series router (ERX/ES2, JUNOSe)
Monitoring Examples
An operator can poll juniMplsGroupLabelRangeLow and juniMplsGroupLabelRangeHigh to confirm the configured label space, and watch juniMplsGroupLspRetryTimesNoroute together with juniMplsGroupLspRetryIntervalNoroute to see how persistently the router is retrying LSP setup when no route to the destination exists — a high retry count signals an ongoing reachability failure blocking tunnel establishment. juniMplsGroupLdpRetryTimes and juniMplsGroupLdpRetryInterval similarly expose LDP session flapping. juniMplsGroupReopTimer shows how the router paces re-optimization of already-established tunnels.
What Can Be Monitored
- MPLS enable/global config status
- label range allocation
- LSP retry attempts/intervals on no-route conditions
- LDP retry attempts/intervals
- tunnel re-optimization timer
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero |
From Juniper-MIBs
| juniMibs | MODULE-IDENTITY |
From Juniper-TC
| JuniNextIfIndex |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| juniMplsMIB | 1.3.6.1.4.1.4874.2.2.54 | The MultiProtocol Label Switching (MPLS) MIB for the Juniper Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations. | ||
| juniMplsObjects | 1.3.6.1.4.1.4874.2.2.54.1 | |||
| juniMplsLsrGlobalConfig | 1.3.6.1.4.1.4874.2.2.54.1.1 | |||
| juniMplsGroup | 1.3.6.1.4.1.4874.2.2.54.1.1.1 | |||
| INT juniMplsGroupMplsEnable | 1.3.6.1.4.1.4874.2.2.54.1.1.1.1 | INTEGER | read-write | Enables or disables MPLS on the virtual router. When MPLS is created on the virtual router (VR), it remains adminstratively disabled untill it is enabled explicitly. Without administratively enabling the MPLS on VR, it won't function as an LSR even though it holds the MPLS configurations until the MPLS context is destroyed for the VR. |
| I32 juniMplsGroupReopTimer | 1.3.6.1.4.1.4874.2.2.54.1.1.1.2 | Integer32 | read-write | All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. This object allows configuration of the frequency of reoptimization in time interval. |
| I32 juniMplsGroupLabelRangeLow | 1.3.6.1.4.1.4874.2.2.54.1.1.1.3 | Integer32 | read-write | The lower end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently. |
| I32 juniMplsGroupLabelRangeHigh | 1.3.6.1.4.1.4874.2.2.54.1.1.1.4 | Integer32 | read-write | The higher end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently. |
| I32 juniMplsGroupLspRetryTimesNoroute | 1.3.6.1.4.1.4874.2.2.54.1.1.1.5 | Integer32 | read-write | This object configures the number of retries for LSP setup after a failure due to no available route. |
| I32 juniMplsGroupLspRetryIntervalNoroute | 1.3.6.1.4.1.4874.2.2.54.1.1.1.6 | Integer32 | read-write | This object configures the time interval between two successive LSP setup retries after a failure due to no available route. |
| I32 juniMplsGroupLspRetryTimes | 1.3.6.1.4.1.4874.2.2.54.1.1.1.7 | Integer32 | read-write | Use this object to configure number of retries for LSP setup after a failure other than one due to no available route. |
| I32 juniMplsGroupLspRetryInterval | 1.3.6.1.4.1.4874.2.2.54.1.1.1.8 | Integer32 | read-write | Use this object to configure the time interval between two LSP setup retries after a failure other than one due to no available route. |
| I32 juniMplsGroupLdpRetryTimesNoroute | 1.3.6.1.4.1.4874.2.2.54.1.1.1.9 | Integer32 | read-write | Use this object to configure the number of retries for LDP to setup LSP after a failure due to no available route. |
| I32 juniMplsGroupLdpRetryIntervalNoroute | 1.3.6.1.4.1.4874.2.2.54.1.1.1.10 | Integer32 | read-write | Use this object to configure the time interval between two successive LSP setup retries by LDP after a failure due to no available route. |
| I32 juniMplsGroupLdpRetryTimes | 1.3.6.1.4.1.4874.2.2.54.1.1.1.11 | Integer32 | read-write | Use this object to configure LSP setup retries by LDP after a failure other than one due to no available route. |
| I32 juniMplsGroupLdpRetryInterval | 1.3.6.1.4.1.4874.2.2.54.1.1.1.12 | Integer32 | read-write | Use this object to configure time interval between two LSP setup retries by LDP after a failure other than one due to no available route. |
| I32 juniMplsGroupLdpSessionRetries | 1.3.6.1.4.1.4874.2.2.54.1.1.1.13 | Integer32 | read-write | Use this object to configure the number of LDP session retries. |
| I32 juniMplsGroupLdpSessionRetryTimer | 1.3.6.1.4.1.4874.2.2.54.1.1.1.14 | Integer32 | read-write | Use this object to configure the time interval between two LDP session retries. |
| STR juniMplsGroupTopologyDrivenIpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.1.1.15 | DisplayString | read-write | Usually IP interfaces are stacked on top of the MPLS tunnels. The profiled tunnels are associated with IP interfaces with profile of IP interfaces. This object configures the name for the IP profile. |
| T/F juniMplsGroupTopologyDrivenLdpEgressIpIntf | 1.3.6.1.4.1.4874.2.2.54.1.1.1.16 | TruthValue | read-write | This object allows enabling/disabling of IP interfaces created over egress LSPs setup by topology driven LSP setup configurations. |
| T/F juniMplsGroupTopologyDrivenLdpIngressIpIntf | 1.3.6.1.4.1.4874.2.2.54.1.1.1.17 | TruthValue | read-write | This object allows enabling/disabling of IP interfaces created over ingress LSPs setup by topology driven LSP setup configurations. |
| T/F juniMplsGroupTopologyDrivenLdpEgressIpIntfHostOnly | 1.3.6.1.4.1.4874.2.2.54.1.1.1.18 | TruthValue | read-write | This object allows enabling/disabling of IP interfaces created over egress LSPs to host only IP addresses setup by topology driven LSP setup configurations. |
| T/F juniMplsGroupTopologyDrivenLdpIngressIpIntfHostOnly | 1.3.6.1.4.1.4874.2.2.54.1.1.1.19 | TruthValue | read-write | This object allows enabling/disabling of IP interfaces created over ingress LSPs to host only IP addresses setup by topology driven LSP setup configurations. |
| INT juniMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListType | 1.3.6.1.4.1.4874.2.2.54.1.1.1.20 | INTEGER | read-write | There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the egress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently. |
| INT juniMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListType | 1.3.6.1.4.1.4874.2.2.54.1.1.1.21 | INTEGER | read-write | There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the ingress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently. |
| STR juniMplsGroupTopologyDrivenLdpEgressIpIntfPolicyList | 1.3.6.1.4.1.4874.2.2.54.1.1.1.22 | DisplayString | read-write | This object used to configure egress list name of topology driven LSPs over IP interfaces. For successful configurations the egress list name must be set cunncurently with egress list type. Set the list type and list name cuncurrently. |
| STR juniMplsGroupTopologyDrivenLdpIngressIpIntfPolicyList | 1.3.6.1.4.1.4874.2.2.54.1.1.1.23 | DisplayString | read-write | This object used to configure ingress list name of topology driven LSPs over IP interfaces. For successful configurations ingress listname set cunncurently with ingress list type. Set the list type and list name cuncurrently. |
| INT juniMplsGroupTopologyDrivenLdp | 1.3.6.1.4.1.4874.2.2.54.1.1.1.24 | INTEGER | read-write | LDP is used for label distributions control for setting up the LSPs. Topology driven LSPs also setup using LDP label distribution control. This object allows to enable/disable LDP admin state used for topology driven LSPs setup. |
| INT juniMplsGroupLspLabelDistCtrlMode | 1.3.6.1.4.1.4874.2.2.54.1.1.1.25 | INTEGER | read-only | Some FECs correspond to address prefixes which are distributed via a dynamic routing algorithm. The setup of the LSPs for these FECs can be done in one of two ways: Independent LSP Control or Ordered LSP Control. This object displays the LSP lable distribution control mode. |
| T/F juniMplsGroupLdpAdvHostOnly | 1.3.6.1.4.1.4874.2.2.54.1.1.1.26 | TruthValue | read-write | This object allows to enable/disable LDP label advertisement mode for host only LSPs. |
| STR juniMplsGroupLsrState | 1.3.6.1.4.1.4874.2.2.54.1.1.1.27 | DisplayString | read-only | This object value displays the status of MPLS enabled LSR such as state is up or down etc. |
| T/F juniMplsGroupReopNow | 1.3.6.1.4.1.4874.2.2.54.1.1.1.28 | TruthValue | read-write | All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. Setting this object forces an immediate check for better paths for the existing LSPs. |
| INT juniMplsGroupIpTtlPropagate | 1.3.6.1.4.1.4874.2.2.54.1.1.1.29 | INTEGER | read-write | Indicate the IP TTL propagation status on ingress LSPs. none - Not set to anything. hideForwardedAndLocal - Hide LSP topology from local and forwarded traffic. hideForwarded - Hide LSP topology from forwarded traffic only. hideLocal - Hide LSP topology from local traffic only. |
| juniMplsGroupList | 1.3.6.1.4.1.4874.2.2.54.1.1.2 | |||
| juniMplsGroupTargetedHelloSendTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.1 | not-accessible | This table contains list of send side IP addresses for LDP targeted hello messages. | |
| juniMplsGroupTargetedHelloSendEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1 | not-accessible | Each entry represents send IP address for targeted hello message. | |
| IP juniMplsGroupTargetedHelloSendAddress | 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.1 | IpAddress | not-accessible | Configure the send side address for targeted hello messages. |
| INT juniMplsGroupLdpTargetedHelloSendMode | 1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.2 | INTEGER | read-create | Select mode to add/delete to the list of IP addresses for targeted hello messages. |
| juniMplsGroupTargetedHelloReceiveTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.2 | not-accessible | This table contains list of receive side IP addresses for LDP targeted hello messages. | |
| juniMplsGroupTargetedHelloReceiveEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1 | not-accessible | Each entry represents receive IP address for targeted hello message. | |
| IP juniMplsGroupTargetedHelloReceiveAddress | 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.1 | IpAddress | not-accessible | Configure the receive side address for targeted hello messages. |
| INT juniMplsGroupLdpTargetedHelloReceiveMode | 1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.2 | INTEGER | read-create | Select mode to add/delete to the list of IP addresses for targeted hello messages. |
| juniMplsGroupLdpLabelAdverRouteListTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3 | not-accessible | Table is a list of LDP label advertisement entries. | |
| juniMplsGroupLdpLabelAdverRouteListEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1 | not-accessible | Each entry represents access list pairs for the LDP peers label advertisement. | |
| STR juniMplsGroupLdpLabelAdverRouteListName | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.1 | DisplayString | not-accessible | This LDP label advertisement route list name for which this entry contains information. |
| STR juniMplsGroupLdpLabelAdverNbrListName | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.2 | DisplayString | not-accessible | The LDP label advertisement neighbor route list name for which this entry contains information. |
| INT juniMplsGroupLabelAdverListMode | 1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.3 | INTEGER | read-create | This object selects the mode of addition/deletion to the list. |
| juniMplsGroupLdpProfileTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4 | not-accessible | Table is a list of LDP Profile entries. | |
| juniMplsGroupLdpProfileEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1 | not-accessible | Each entry represents one LDP profile settings. | |
| STR juniMplsGroupLdpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.1 | DisplayString | not-accessible | LDP profile name identifies unique entry in the table. |
| I32 juniMplsGroupLdpProfileHelloHoldTime | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.2 | Integer32 | read-create | Configure the LDP peers hello hold time period. |
| INT juniMplsGroupLdpProfileCrLdpAdminState | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.3 | INTEGER | read-create | Enable or disable the constraint-based routing label distribution protocol (CR-LDP) admin state. |
| ROW juniMplsGroupLdpProfileRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.4 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsGroupLdpProfileCrLdpAdminState juniMplsGroupLdpProfileRowStatus |
| juniMplsGroupRsvpProfileTable | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5 | not-accessible | Table is a list of LDP Profile entries. | |
| juniMplsGroupRsvpProfileEntry | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1 | not-accessible | Each entry represents one LDP profile settings. | |
| STR juniMplsGroupRsvpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.1 | DisplayString | not-accessible | The RSVP profile name identifies unique entry in the table. |
| U32 juniMplsGroupRsvpProfileRefreshPeriod | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.2 | Unsigned32 | read-create | Configure the time out period between the generation of two refresh messages. |
| I32 juniMplsGroupRsvpProfileCleanupTimeoutFactor | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.3 | Integer32 | read-create | Confgure the number of refresh messages can be lost before PATH or RESV state is ended. |
| ROW juniMplsGroupRsvpProfileRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.4 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: juniMplsGroupRsvpProfileRowStatus |
| juniMplsMajorLayer | 1.3.6.1.4.1.4874.2.2.54.1.2 | |||
| juniMplsIfMajorLayer | 1.3.6.1.4.1.4874.2.2.54.1.2.1 | |||
| JUN juniMplsIfMajorNextIfIndex | 1.3.6.1.4.1.4874.2.2.54.1.2.1.1 | JuniNextIfIndex | read-only | Coordinate ifIndex value allocation for entries in the juniMplsIfMajorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. |
| juniMplsIfMajorTable | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2 | not-accessible | This table contains entries for MPLS Major interfaces present in the system. | |
| juniMplsIfMajorEntry | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1 | not-accessible | Each entry describes the characteristics of an MPLS Major interface. Creating/deleting entries in this table causes corresponding entries to be created/deleted in ifTable/ifXTable/juniIfTable. | |
| NUM juniMplsIfMajorIndex | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.1 | InterfaceIndex | not-accessible | The ifIndex of the MPLS Major interface. When creating entries in this table, suitable values for this object are determined by reading juniMplsIfMajorNextIfIndex. |
| ROW juniMplsIfMajorRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.2 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMajorRowStatus juniMplsIfMajorLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniMplsIfMajorIndex must have been determined previously, by reading juniMplsIfMajorNextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table. |
| NUM juniMplsIfMajorLowerIfIndex | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.3 | InterfaceIndexOrZero | read-create | The ifIndex of an interface over which this MPLS Major interface to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation. |
| INT juniMplsIfMajorAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.4 | INTEGER | read-create | Use this object to create MPLS major interface stacked over any link layer interface. Lower layer(index) over which major stacks has to be specified for successful creation of the major interface. |
| INT juniMplsIfMajorLdpAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.5 | INTEGER | read-create | This object enables/disables LDP admin status on the MPLS interface. |
| STR juniMplsIfMajorLdpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.6 | DisplayString | read-create | All the LDP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the LDP profile name. |
| JUN juniMplsIfMajorLdpVpiStart | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.7 | JuniMajorCfgVpiRanges | read-create | This object is defined to support configurations of interface label space. This configures the start range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the stop range cunncurrently. |
| JUN juniMplsIfMajorLdpVpiStop | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.8 | JuniMajorCfgVpiRanges | read-create | This object is defined to support configurations of interface label space. This configures the stop range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the start range cunncurrently. |
| JUN juniMplsIfMajorLdpVciStart | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.9 | JuniMajorCfgVciRanges | read-create | This object is defined to support configurations of interface label space. This configures the start range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the stop range cunncurrently. |
| JUN juniMplsIfMajorLdpVciStop | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.10 | JuniMajorCfgVciRanges | read-create | This object is defined to support configurations of interface label space. This configures the stop range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the start range cunncurrently. |
| INT juniMplsIfMajorRsvpAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.11 | INTEGER | read-create | This object configures RSVP admin status for MPLS interface. |
| STR juniMplsIfMajorRsvpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.12 | DisplayString | read-create | All the RSVP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the RSVP profile name. |
| JUN juniMplsIfMajorRsvpVpiStart | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.13 | JuniMajorCfgVpiRanges | read-create | This object is defined to support configurations of interface label space. This configures the start range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the stop range cunncurrently. |
| JUN juniMplsIfMajorRsvpVpiStop | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.14 | JuniMajorCfgVpiRanges | read-create | This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the start range cunncurrently. |
| JUN juniMplsIfMajorRsvpVciStart | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.15 | JuniMajorCfgVciRanges | read-create | This object is defined to support configurations of interface label space. This configures the start range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the stop range cunncurrently. |
| JUN juniMplsIfMajorRsvpVciStop | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.16 | JuniMajorCfgVciRanges | read-create | This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the start range cunncurrently. |
| INT juniMplsIfMajorLabelSpaceType | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.17 | INTEGER | read-only | Displays the label space type for the MPLS interface. |
| INT juniMplsIfMajorOpState | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.18 | INTEGER | read-only | This object displays MPLS major interface operation state. |
| INT juniMplsIfMajorCrLdpAdminState | 1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.19 | INTEGER | read-only | This object displays the admin state of CR-LDP. |
| juniMplsMinorLayer | 1.3.6.1.4.1.4874.2.2.54.1.3 | |||
| juniMplsIfMinorLayer | 1.3.6.1.4.1.4874.2.2.54.1.3.1 | |||
| JUN juniMplsIfMinorNextIfIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.1.1 | JuniNextIfIndex | read-only | Coordinates ifIndex value allocation for entries in the juniMplsIfMinorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. |
| juniMplsIfMinorTable | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2 | not-accessible | This table contains entries for MPLS Minor interfaces present in the system. | |
| juniMplsIfMinorEntry | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1 | not-accessible | Each entry describes the characteristics of an MPLS Minor interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable. | |
| NUM juniMplsIfMinorIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.1 | InterfaceIndex | not-accessible | The ifIndex of the MPLS Minor interface. When creating entries in this table, suitable values for this object are determined by reading juniMplsMinorNextIfIndex. |
| ROW juniMplsIfMinorRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.2 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create/delete an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMinorRowStatus juniMplsIfMinorTunnelName In addition, when creating an entry the following conditions must hold: A value for juniMplsIfMinorIndex must have been determined previously, by reading juniMplsMinorNextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table. |
| NUM juniMplsIfMinorLowerIfIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.3 | InterfaceIndexOrZero | read-only | The ifIndex of an interface over which this MPLS Minor interface is to be layered. A value of zero indicates no layering. As minor interface can be created without stacking on major interface, as and when it stacks on major interface by signalling protocol, it's value can be read. |
| INT juniMplsIfMinorAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.4 | INTEGER | read-create | With this object minor interface admin status can be enabled/disabled. |
| IP juniMplsIfMinorEndpointAddress | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.5 | IpAddress | read-create | This object configures the IP address of the tunnel destination. This object can be set along with the juniMplsIfMinorEndpointDstMask to configure the tunnel destination mask, but it is optional. |
| IP juniMplsIfMinorEndpointDstMask | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.6 | IpAddress | read-create | This object configures the tunnel destination mask. It can be set along with the juniMplsIfMinorEndpointAddress. |
| INT juniMplsIfMinorTunnelMetricMode | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.7 | INTEGER | read-create | Select the relative or absolute mode to configure the absolute or relative tunnel metric. To set the tunnel to relative metric, juniMplsIfMinorRelativeTunnelMetric has to be set along with this object option as relative. To set the tunnel to absolute metric, juniMplsIfMinorAbsoluteTunnelMetric has to be set along with this object option as absolute. |
| U32 juniMplsIfMinorAbsoluteTunnelMetric | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.8 | Unsigned32 | read-create | This object allows configuration of absolute metric values. Refer to juniMplsIfMinorTunnelMetricMode for how set it. |
| I32 juniMplsIfMinorRelativeTunnelMetric | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.9 | Integer32 | read-create | This object allows configuration of relative metric values. Refer to juniMplsIfMinorTunnelMetricMode for how set it. |
| INT juniMplsIfMinorLabelDistProto | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.10 | INTEGER | read-create | This object allows to select label distribution protocol. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels. |
| T/F juniMplsIfMinorAnnounceToOspf | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.11 | TruthValue | read-create | This object allows to register LSP endpoints to OSPF to next hop calculation. |
| T/F juniMplsIfMinorAnnounceToIsis | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.12 | TruthValue | read-create | This object allows to register LSP endpoints to IS-IS for next hop calculation. |
| T/F juniMplsIfMinorAnnounceToBgp | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.13 | TruthValue | read-create | This object allows to register LSP endpoints to BGP for next hop calculation. |
| JUN juniMplsIfMinorBandwidth | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.14 | JuniMinorCfgBWRanges | read-create | This object allows configuration of bandwidth requirements for the tunnel. |
| OCT juniMplsIfMinorAffinity | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.15 | OCTET STRING | read-create | This object allows configuration of resource class affinity for the tunnel. |
| OCT juniMplsIfMinorAffinityMask | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.16 | OCTET STRING | read-create | This allows to set the resource class affinity mask. Since it is a mask, set along with the affinity for successful configurations. |
| JUN juniMplsIfMinorSetupPriority | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.17 | JuniMinorCfgHoldingAndSetupPriorityRanges | read-create | This object allows configuration of preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| JUN juniMplsIfMinorHoldingPriority | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.18 | JuniMinorCfgHoldingAndSetupPriorityRanges | read-create | This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| STR juniMplsIfMinorTunnelName | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.19 | DisplayString | read-create | This object allows configuration of the tunnel name to be associated with tunnel settings. |
| JUN juniMplsIfMinorTunnelRetryTimes | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.20 | JuniMinorCfgRetryTimesAndNorouteRanges | read-create | This object allows configuration of the number of retries for tunnel setup. |
| NUM juniMplsIfMinorTunnelRetryInterval | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.21 | JuniMinorCfgRetryIntervalAndNorouteRanges | read-create | This object allows configuration of retry interval for tunnel setup. |
| JUN juniMplsIfMinorTunnelRetryTimesNoroute | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.22 | JuniMinorCfgRetryTimesAndNorouteRanges | read-create | This object allows configuration of the tunnel retries when no route notifications are received. |
| NUM juniMplsIfMinorTunnelRetryIntervalNoroute | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.23 | JuniMinorCfgRetryIntervalAndNorouteRanges | read-create | This object allows configuration of the tunnel retry interval when no route notifications are received. |
| STR juniMplsIfMinorBaseTunnelName | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.24 | DisplayString | read-create | This object allows configuration of the base tunnel name over which all the tunnels are stacked over. |
| I32 juniMplsIfMinorVpnOuiNumber | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.25 | Integer32 | read-create | This object allows configuration of the OUI part of VPN ID. |
| IP juniMplsIfMinorVpnIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.26 | IpAddress | read-create | This object allows configuration of the index part of VPN ID. |
| INT juniMplsIfMinorTunnelOpState | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.27 | INTEGER | read-only | This object displays the tunnel operation state. established : Tunnel established teNegotiation : TE Negotiation up : Tunnel Up down : Tunnel Down cfgChanged : Tunnel config changed cfgIncEn : Tunnel incomplete Config Admin State Enable cfgIncDis : Tunnel incomplete Config Admin State Disable disabled : Tunnel disabled rel : noChange : Tunnel state no change |
| T/F juniMplsIfMinorTargetedDynamicTunnel | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.28 | TruthValue | read-create | Configure targeted dynamic tunnel. |
| T/F juniMplsIfMinorReoptimization | 1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.29 | TruthValue | read-create | Configure tunnel reoptimization. |
| juniMplsMinorLayerList | 1.3.6.1.4.1.4874.2.2.54.1.3.2 | |||
| juniMplsIfMinorPathOptionTable | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1 | not-accessible | Table is a list of different LSP paths as option for each LSP setup. | |
| juniMplsIfMinorPathOptionEntry | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1 | not-accessible | Each entry represents one path option for the LSP. | |
| NUM juniMplsIfMinorPathOptionIndex | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.1 | InterfaceIndex | not-accessible | Minor interface unique ID. |
| I32 juniMplsIfMinorPathOptionNumber | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.2 | Integer32 | not-accessible | Unique number to identify each path option configured. |
| INT juniMplsIfMinorPathOptionProtocol | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.3 | INTEGER | read-create | Select the each path option explicit routing protocol. |
| T/F juniMplsIfMinorPathOptionLockdown | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.4 | TruthValue | read-create | Enable/disable each configured path option reoptimization. |
| STR juniMplsIfMinorPathOptionPathName | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.5 | DisplayString | read-create | Configure the name for each path option. |
| I32 juniMplsIfMinorPathOptionPathId | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.6 | Integer32 | read-create | Configure the path option ID. Either the name or ID will be associated with a path at a time. If the path name and ID are set at a same time for the path, the name will have precedence over ID. |
| ROW juniMplsIfMinorPathOptionRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.7 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMinorPathOptionRowStatus. |
| juniMplsTunnelProfile | 1.3.6.1.4.1.4874.2.2.54.1.4 | |||
| juniMplsTunnelProfileGroup | 1.3.6.1.4.1.4874.2.2.54.1.4.1 | |||
| juniMplsTunnelProfileTable | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1 | not-accessible | Table is a list of tunnel profiles for a given VR. | |
| juniMplsTunnelProfileEntry | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1 | not-accessible | Each entry represents one tunnel profile. | |
| STR juniMplsTunnelProfileName | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.1 | DisplayString | not-accessible | Associate a name for the configured tunnel profile settings. |
| INT juniMplsTunnelProfileAdminStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.2 | INTEGER | read-create | Enable/disable the adminstatus of the tunnel profile. |
| STR juniMplsTunnelProfileBaseTunnelName | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.3 | DisplayString | read-create | Configure the base tunnel name in tunnel profile settings. This base tunnel is the one over which all the other tunnels are stacked over. Configured base tunnel name in profile settings will be associated with the actual configured base tunnel name. |
| STR juniMplsTunnelProfileIpProfileName | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.4 | DisplayString | read-create | Configures the name for IP profile settings for the IP interfaces over which MPLS tunnels are stacked. |
| INT juniMplsTunnelProfileLabelDistProto | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.5 | INTEGER | read-create | Configure the label distribution protocol to associate with a tunnel profile. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels. |
| T/F juniMplsTunnelProfileAnnounceToOspf | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.6 | TruthValue | read-create | Configure the routing protocol for next hop calculations as OSPF. |
| T/F juniMplsTunnelProfileAnnounceToIsis | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.7 | TruthValue | read-create | Configure routing protocol for next hop calculations as ISIS. |
| T/F juniMplsTunnelProfileAnnounceToBgp | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.8 | TruthValue | read-create | Configure routing protocol for next hop calculations as BGP. |
| INT juniMplsTunnelProfileMetricMode | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.9 | INTEGER | read-create | Select the relative or absolute mode to configure the absolute or relative tunnel profile metric. To set the tunnel profile to relative metric, juniMplsTunnelProfileRelativeMetric has to be set along with this object option as relative. To set the tunnel profile to absolute metric, juniMplsTunnelProfileAbsoluteMetric has to be set along with this object option as absolute. |
| U32 juniMplsTunnelProfileAbsoluteMetric | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.10 | Unsigned32 | read-create | This object allows configuration of the absolute metric values. Refer to juniMplsTunnelProfileMetricMode for how set it. |
| I32 juniMplsTunnelProfileRelativeMetric | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.11 | Integer32 | read-create | This object allows configuration of the relative metric values. Refer to juniMplsTunnelProfileMetricMode for how set it. |
| JUN juniMplsTunnelProfileBandwidth | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.12 | JuniProfileCfgBWRanges | read-create | This object allows configuration of bandwidth requirements for the tunnel. |
| OCT juniMplsTunnelProfileAffinity | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.13 | OCTET STRING | read-create | This object allows configuration of the resource class affinity for the tunnel. This can set independently of juniMplsTunnelProfileAffinityMask. |
| OCT juniMplsTunnelProfileAffinityMask | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.14 | OCTET STRING | read-create | This allows configuration of which bits in the affinity must match the resource class bits. Can't be set independently; always with juniMplsTunnelProfileAffinity. Specify the value in bit mask format. |
| JUN juniMplsTunnelProfileSetupPriority | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.15 | JuniProfileCfgHoldingAndSetupPriorityRanges | read-create | This object configuration of the preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| JUN juniMplsTunnelProfileHoldingPriority | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.16 | JuniProfileCfgHoldingAndSetupPriorityRanges | read-create | This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority. |
| JUN juniMplsTunnelProfileRetryTimes | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.17 | JuniProfileCfgRetryTimesAndNorouteRanges | read-create | This object allows configuration of the number of retries for the tunnel setup. |
| NUM juniMplsTunnelProfileRetryInterval | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.18 | JuniProfileCfgRetryIntervalAndNorouteRanges | read-create | This object allows configuration of retry interval for tunnel setup. |
| JUN juniMplsTunnelProfileRetryTimesNoroute | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.19 | JuniProfileCfgRetryTimesAndNorouteRanges | read-create | This object allows configuration of the tunnel retries when no route notifications are received. |
| NUM juniMplsTunnelProfileRetryIntervalNoroute | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.20 | JuniProfileCfgRetryIntervalAndNorouteRanges | read-create | This object allows configuration of the tunnel retry interval when no route notifications are received. |
| I32 juniMplsTunnelProfileVpnOuiNumber | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.21 | Integer32 | read-create | This object allows configuration of the OUI part of VPN ID. |
| IP juniMplsTunnelProfileVpnIndex | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.22 | IpAddress | read-create | This object allows configuration of the index part of VPN ID. |
| ROW juniMplsTunnelProfileRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.23 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfileRowStatus |
| T/F juniMplsTunnelProfileTargetedDynamicTunnel | 1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.24 | TruthValue | read-create | Configure targeted dynamic tunnel. |
| juniMplsTunnelProfileList | 1.3.6.1.4.1.4874.2.2.54.1.4.2 | |||
| juniMplsTunnelProfilePathOptionTable | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1 | not-accessible | Table is a list of different LSP paths as option for each LSP setup, configured as part of tunnel profile settings | |
| juniMplsTunnelProfilePathOptionEntry | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1 | not-accessible | Each entry represents one path option for the LSP setup, configured as a part of tunnel profile settings. | |
| STR juniMplsTunnelProfileNamePathOption | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.1 | DisplayString | not-accessible | Name of the path option. |
| I32 juniMplsTunnelProfilePathOptionNumber | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.2 | Integer32 | not-accessible | Unique identifier for the path option. |
| INT juniMplsTunnelProfilePathOptionProtocol | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.3 | INTEGER | read-create | Path selection option protocol. |
| T/F juniMplsTunnelProfilePathOptionLockdown | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.4 | TruthValue | read-create | Enable/disable path selection option reoptimization. |
| STR juniMplsTunnelProfilePathOptionPathName | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.5 | DisplayString | read-create | Associate a name with each explicit path. |
| I32 juniMplsTunnelProfilePathOptionPathId | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.6 | Integer32 | read-create | Each explicit path can be associated either name or ID. This object allows configuration of the ID for the explicit path. |
| ROW juniMplsTunnelProfilePathOptionRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.7 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfilePathOptionRowStatus. |
| juniMplsTunnelProfileDynamicEndpointTable | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2 | not-accessible | This table contains entries for the dynamic endpoints configured for each tunnel profile. | |
| juniMplsTunnelProfileDynamicEndpointEntry | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1 | not-accessible | Dynamic endpoint entries for each tunnel profile. | |
| STR juniMplsTunnelProfileNameDynamicEndpoint | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.1 | DisplayString | not-accessible | Configure the tunnel dynamic endpoint in tunnel profile settings. |
| INT juniMplsTunnelProfileDynamicEndpointType | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.2 | INTEGER | not-accessible | Configure the dynamic endpoint type for the tunnel. |
| INT juniMplsTunnelProfileDynamicEndpointPolicyListType | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.3 | INTEGER | not-accessible | This object allows configuration of the dynamic tunnel policy type selection. |
| STR juniMplsTunnelProfileDynamicEndpointListName | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.4 | DisplayString | not-accessible | This object allows configuration of the dynamic endpoints access list name. |
| ROW juniMplsTunnelProfileDynamicEndpointRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.5 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: juniMplsTunnelProfileDynamicEndpointRowStatus. |
| juniMplsTunnelProfileTunnelEndpointTable | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3 | not-accessible | Table contains list of tunnel static enpoints configured for each tunnel profile. | |
| juniMplsTunnelProfileTunnelEndpointEntry | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1 | not-accessible | Each entry represents one static endpoint configuration for the tunnel. | |
| STR juniMplsTunnelProfileNameTunnelEndpoint | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.1 | DisplayString | not-accessible | This object configures the tunnel profile name. |
| IP juniMplsTunnelProfileTunnelEndpointAddress | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.2 | IpAddress | not-accessible | This object configures the IP address of the tunnel destination. |
| IP juniMplsTunnelProfileTunnelEndpointDstMask | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.3 | IpAddress | not-accessible | This object configures the tunnel destination mask. A value of 255.255.255.255 is expected. |
| ROW juniMplsTunnelProfileTunnelEndpointRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.4 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfileTunnelEndpointRowStatus. |
| juniMplsExplicitPath | 1.3.6.1.4.1.4874.2.2.54.1.5 | |||
| juniMplsExplicitPathGroup | 1.3.6.1.4.1.4874.2.2.54.1.5.1 | |||
| juniMplsExplicitPathTable | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1 | not-accessible | Table is a list of hops configurations for explicit paths. | |
| juniMplsExplicitPathEntry | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1 | not-accessible | Each entry represents one hop configuration for the particular explicit path. | |
| STR juniMplsExplicitPathName | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.1 | DisplayString | not-accessible | Configure the name for the explicit path used as table index. |
| INT juniMplsExplicitPathAdminState | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.2 | INTEGER | read-create | Enable/disable explicit path adminstatus. |
| ROW juniMplsExplicitPathRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.3 | RowStatus | read-create | Creation/deletion of the explicit path is done through setting this object. |
| juniMplsExplicitPathNodeTable | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2 | not-accessible | Table is a list of configured explicit paths. | |
| juniMplsExplicitPathNodeEntry | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1 | not-accessible | Each entry represents one hop in a particular explicit path. | |
| STR juniMplsExplicitPathNodeName | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.1 | DisplayString | not-accessible | Configure the name for the explicit path used in the table index. |
| I32 juniMplsExplicitPathNodeIndexNumber | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.2 | Integer32 | not-accessible | Each explicit path hop will have an index associated with it. Configure each path hop index using this object. |
| T/F juniMplsExplicitPathNodeLoose | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.3 | TruthValue | read-create | Configure the explicit path hop as strict or loose. Set along with HopAddress. |
| IP juniMplsExplicitPathNodeHopAddress | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.4 | IpAddress | read-create | Configure the hop IP address to setup explicit path. Explicit path next hop will be created when the mentioned hop IP address doesn't belong to any of the existing hop even without setting the rowStatus createAndGo value. The rowStatus value is used to destroy the node. |
| IP juniMplsExplicitPathNodeHopAddressMask | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.5 | IpAddress | read-create | Configure the hop IP address mask. Set along with hop address. |
| ROW juniMplsExplicitPathNodeRowStatus | 1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.6 | RowStatus | read-create | Use this object for deletion of the node. For node creation, this value have no effect. Setting the node with IP address create the node. To delete the node set only this object. |
| juniMplsConformance | 1.3.6.1.4.1.4874.2.2.54.2 | |||
| juniMplsCompliances | 1.3.6.1.4.1.4874.2.2.54.2.1 | |||
| juniMplsCompliance | 1.3.6.1.4.1.4874.2.2.54.2.1.1 | Obsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement became obsolete when RowStatus support was added to some of the minor layer and tunnel profile tables. | ||
| juniMplsCompliance2 | 1.3.6.1.4.1.4874.2.2.54.2.1.2 | Obsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement became obsolete when the juniMplsGroupIpTtlPropagate object was added to the juniMplsGroup scalar group. | ||
| juniMplsCompliance3 | 1.3.6.1.4.1.4874.2.2.54.2.1.3 | Obsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement become obsolete when the objects juniMplsIfMajorCrLdpAdminState, juniMplsIfMinorLabelDistProto, juniMplsIfMinorBaseTunnelName, juniMplsIfMinorVpnOuiNumber, juniMplsIfMinorVpnIndex, juniMplsIfMinorTargetedDynamicTunnel, juniMplsTunnelProfileBaseTunnelName, juniMplsTunnelProfileLabelDistProto, juniMplsTunnelProfileVpnOuiNumber, juniMplsTunnelProfileVpnIndex, juniMplsTunnelProfileTargetedDynamicTunnel, juniMplsGroupLdpRetryTimesNoroute, juniMplsGroupLdpRetryTimes, juniMplsGroupLdpRetryIntervalNoroute and juniMplsGroupLdpProfileCrLdpAdminState became obsolete. | ||
| juniMplsCompliance4 | 1.3.6.1.4.1.4874.2.2.54.2.1.4 | The compliance statement for entities which implement the Juniper MPLS MIB. | ||
| juniMplsConfGroups | 1.3.6.1.4.1.4874.2.2.54.2.2 | |||
| juniMplsLsrGlobalConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.1 | Obsolete collection of objects providing management of MPLS global configurations in a Juniper product. This group became obsolete when the object juniMplsGroupIpTtlPropagate was added. | ||
| juniMplsMajorLayerConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.2 | A collection of objects providing management of major MPLS interfaces in a Juniper product. This group became obsolete when the object juniMplsIfMajorCrLdpAdminState became obsolete. | ||
| juniMplsMinorLayerConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.3 | Obsolete collection of objects providing management of minor MPLS (tunnel) in a Juniper product. This group became obsolete when the juniMplsIfMinorPathOptionRowStatus object was added. | ||
| juniMplsTunnelProfileConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.4 | Obsolete collection of objects providing management of MPLS tunnel profiles in a Juniper product. This group became obsolete when RowStatus objects were added to some of the tables. | ||
| juniMplsExplicitPathConfGroup | 1.3.6.1.4.1.4874.2.2.54.2.2.5 | A collection of objects providing management of MPLS explicit paths in a Juniper product. | ||
| juniMplsMinorLayerConfGroup2 | 1.3.6.1.4.1.4874.2.2.54.2.2.6 | A collection of objects providing management of minor MPLS (tunnel) interfaces in a Juniper product. This group became obsolete when the objects juniMplsIfMinorLabelDistProto, juniMplsIfMinorBaseTunnelName, juniMplsIfMinorVpnOuiNumber, juniMplsIfMinorVpnIndex, juniMplsIfMinorTargetedDynamicTunnel became obsolete. | ||
| juniMplsTunnelProfileConfGroup2 | 1.3.6.1.4.1.4874.2.2.54.2.2.7 | A collection of objects providing management of MPLS tunnel profiles in a Juniper product. This group became oboslete when the objects juniMplsTunnelProfileBaseTunnelName, juniMplsTunnelProfileLabelDistProto, juniMplsTunnelProfileVpnOuiNumber, juniMplsTunnelProfileVpnIndex, juniMplsTunnelProfileTargetedDynamicTunnel became obsolete. | ||
| juniMplsLsrGlobalConfGroup2 | 1.3.6.1.4.1.4874.2.2.54.2.2.8 | A collection of objects providing management of MPLS label switching routers (LSRs) in a Juniper product. This group became obsolete when the object juniMplsGroupLdpRetryTimesNoroute, juniMplsGroupLdpRetryIntervalNoroute, juniMplsGroupLdpRetryTimes and juniMplsGroupLdpProfileCrLdpAdminState became obsolete. | ||
| juniMplsLsrGlobalConfGroup3 | 1.3.6.1.4.1.4874.2.2.54.2.2.9 | A collection of objects providing management of MPLS label switching routers (LSRs) in a Juniper product. | ||
| juniMplsMajorLayerConfGroup2 | 1.3.6.1.4.1.4874.2.2.54.2.2.10 | A collection of objects providing management of major MPLS interfaces in a Juniper product. | ||
| juniMplsMinorLayerConfGroup3 | 1.3.6.1.4.1.4874.2.2.54.2.2.11 | A collection of objects providing management of minor MPLS (tunnel) interfaces in a Juniper product. | ||
| juniMplsTunnelProfileConfGroup3 | 1.3.6.1.4.1.4874.2.2.54.2.2.12 | A collection of objects providing management of MPLS tunnel profiles in a Juniper product |
RFC description
Multiprotocol Label Switching configuration and management for Juniper Networks label switching routers.
Start monitoring Juniper E-series router (ERX/ES2, JUNOSe) — MPLS LSP/tunnel/VPN configuration with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.