Juniper-MROUTER-MIB

All MIBs › Juniper-MROUTER-MIB

Organization: Juniper Networks, Inc.

Last Updated: 2006-09-18

Category: Technology: Multicast, Vendor: Juniper

Description: Juniper Networks MIB for monitoring IP multicast routing tables and multicast protocol state on Juniper E-series edge routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-MROUTER-MIB?

Juniper-MROUTER-MIB is a Juniper Networks vendor MIB for monitoring IP multicast routing tables and multicast protocol state, specifically on Juniper E-series edge routers. It exposes data such as the multicast Reverse Path Forwarding (RPF) route table, static multicast route configuration (destination, mask, preference, RPF next hop), and multicast route bandwidth-admission settings. It is used to monitor the software/routing status of multicast forwarding, letting an admin confirm correct RPF paths are selected (preventing multicast traffic loops or drops) and inspect bandwidth-adaptive route settings to see if a multicast route is being bandwidth-limited. It builds on standard multicast routing concepts from IETF's multicast routing MIBs while adding Juniper-specific static route and bandwidth-admission extensions. It is typically deployed on Juniper E-series routers used as multicast-enabled provider edge or aggregation routers in service-provider IPTV or multicast VPN networks. Engineers can download the Juniper-MROUTER-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-MROUTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks E-series edge routers

Monitoring Examples

Polling juniMcastRpfRouteTable/juniMcastRpfRouteEntry reveals the current RPF interface chosen for a given multicast source, letting an admin verify multicast traffic isn't being dropped due to an RPF-check failure. The juniMcastRouteStaticDest/juniMcastRouteStaticMask/juniMcastRouteStaticRpfHop objects show configured static multicast routes and their designated RPF next hop, useful when troubleshooting a manually configured multicast source route. Checking juniMRouteAdmBwAdaptive and juniMRouteAdmBw on juniMRouteTable entries would reveal whether a particular multicast route is bandwidth-constrained, which could explain degraded IPTV stream quality.

What Can Be Monitored

multicast RPF route selection
static multicast route configuration
multicast route bandwidth admission settings
multicast routing table entries

Imported Objects

From IANA-RTPROTO-MIB

IANAipMRouteProtocol

From IPMROUTE-STD-MIB

ipMRouteEntry	OBJECT-TYPE
ipMRouteInterfaceEntry	OBJECT-TYPE

From Juniper-MIBs

juniMibs

MODULE-IDENTITY

From Juniper-TC

JuniInterfaceLocationType
JuniInterfaceLocationValue

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using juniMRoutePktFwd OID:

Select a Juniper Networks E-series edge router (IP multicast routing/RPF) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type juniMRoutePktFwd into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Packets received that made it out on any egress. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
juniMRouterMIB	1.3.6.1.4.1.4874.2.2.65			The IP multicast router MIB for Juniper Networks enterprise.
juniMRouterMIBObject	1.3.6.1.4.1.4874.2.2.65.1
juniMcastTraps	1.3.6.1.4.1.4874.2.2.65.1.1
NTF juniMRoutePortBwExceded	1.3.6.1.4.1.4874.2.2.65.1.1.1			A juniMRoutePortBwExceded trap signifies the port max admission limit are exceded. This trap should be generated when the OIFs are blocked due to exceded admission limit on the port.
NTF juniMRoutePortBwReceded	1.3.6.1.4.1.4874.2.2.65.1.1.2			A juniMRoutePortBwReceded trap signifies the port max admission limit are receded. This trap should be generated when the the port admission limits fall below the configured hysteresis value on the port.
NTF juniMRoutePortPriorityBwExceded	1.3.6.1.4.1.4874.2.2.65.1.1.3			A juniMRoutePortPriorityBwExceded trap signifies the port priority admission limit are exceded. This trap should be generated when the OIFs are blocked due to exceded admission limit on the port.
NTF juniMRoutePortPriorityBwReceded	1.3.6.1.4.1.4874.2.2.65.1.1.4			A juniMRoutePortPriorityReceded trap signifies the port priority admission limit are receded. This trap should be generated when the the port admission limits fall below the configured hysteresis value on the port.
juniMcastObjects	1.3.6.1.4.1.4874.2.2.65.1.2
juniMcastRpfRouteTable	1.3.6.1.4.1.4874.2.2.65.1.2.1		not-accessible	The table listing the static IP routes for the mcast RPF check.
juniMcastRpfRouteEntry	1.3.6.1.4.1.4874.2.2.65.1.2.1.1		not-accessible	An entry representing the static IP route for the mcast RPF check.
IP juniMcastRouteStaticDest	1.3.6.1.4.1.4874.2.2.65.1.2.1.1.1	IpAddress	not-accessible	The static group's destination IpAddress.
IP juniMcastRouteStaticMask	1.3.6.1.4.1.4874.2.2.65.1.2.1.1.2	IpAddress	not-accessible	The static group's destination IpAddress Mask.
I32 juniMcastRouteStaticRtPreference	1.3.6.1.4.1.4874.2.2.65.1.2.1.1.3	Integer32	read-create	The administrative distance metric.
IP juniMcastRouteStaticRpfHop	1.3.6.1.4.1.4874.2.2.65.1.2.1.1.4	IpAddress	read-create	The next hop IP address.
U32 juniMcastRouteStaticTag	1.3.6.1.4.1.4874.2.2.65.1.2.1.1.5	Unsigned32	read-create	The tag value to be associated.
ROW juniMcastRouteStaticRowStatus	1.3.6.1.4.1.4874.2.2.65.1.2.1.1.6	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMcastRouteStaticRowStatus juniMcastRouteStaticDest juniMcastRouteStaticMask juniMcastRouteStaticRtPreference juniMcastRouteStaticRpfHop juniMcastRouteStaticTag
juniMRouteTable	1.3.6.1.4.1.4874.2.2.65.1.2.2		not-accessible	The table containing the extended information of IP Multicast Route Entry
juniMRouteEntry	1.3.6.1.4.1.4874.2.2.65.1.2.2.1		not-accessible	An entry representing the additional information of IP Multicast Route Entry
T/F juniMRouteAdmBwAdaptive	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.1	TruthValue	read-only	Indicates that bandwidth is measured.
I32 juniMRouteAdmBw	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.2	Integer32	read-only	Multicast Admission Control bandwidth in bps.
T/F juniMRouteQosBwAdaptive	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.3	TruthValue	read-only	Indicates that qos bandwidth is measured.
I32 juniMRouteQosBw	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.4	Integer32	read-only	QoS Adjustment bandwidth in bps.
T/F juniMRouteIsEcmp	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.5	TruthValue	read-only	Indicates RPF route is an ECMP route.
T/F juniMRouteRpfDisabled	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.6	TruthValue	read-only	Indicates that RPF check is disabled for this entry.
IAN juniMRouteOwnerProtoType	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.7	IANAipMRouteProtocol	read-only	Indicates the multicast protocol type.
C64 juniMRoutePktFwdEx	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.8	Counter64	read-only	Packets received that made it out on any egress.
I32 juniMRouteOifCnt	1.3.6.1.4.1.4874.2.2.65.1.2.2.1.9	Integer32	read-only	Indicates the OIF count.
STR juniMcastRpfDisable	1.3.6.1.4.1.4874.2.2.65.1.2.3	DisplayString	read-write	Disable RPF check for the Group access list name. Null value for enabling RPF check for the access list.
juniMRouteInterfaceTable	1.3.6.1.4.1.4874.2.2.65.1.2.4		not-accessible	The (conceptual) table containing multicast routing information specific to interfaces.
juniMRouteInterfaceEntry	1.3.6.1.4.1.4874.2.2.65.1.2.4.1		not-accessible	An entry (conceptual row) containing the multicast routing information for a particular interface.
I32 juniMRouteInterfaceActiveGroups	1.3.6.1.4.1.4874.2.2.65.1.2.4.1.1	Integer32	read-only	This indicates the total number of groups currently forwarded on the interface.
I32 juniMRouteInterfaceBlockedGroups	1.3.6.1.4.1.4874.2.2.65.1.2.4.1.2	Integer32	read-only	This indicates the total number of groups currently blocked on the interface.
NUM juniMroutePortLocationType	1.3.6.1.4.1.4874.2.2.65.1.2.5	JuniInterfaceLocationType	read-only	Describes the interpretation of JuniInterfaceLocationValue object values into platform-dependent interface location components, e.g., 'slot.port' on an ERX.
juniMRoutePortTable	1.3.6.1.4.1.4874.2.2.65.1.2.6		not-accessible	The (conceptual) table containing multicast routing information specific to the number of mroutes (across all VRs) , that have OIFs, on a port.
juniMRoutePortEntry	1.3.6.1.4.1.4874.2.2.65.1.2.6.1		not-accessible	An entry (conceptual row) containing the multicast routing information specific to the number of mroutes (across all VRs) , that have OIFs, on a port.
NUM juniMRoutePortLocationIndex	1.3.6.1.4.1.4874.2.2.65.1.2.6.1.1	JuniInterfaceLocationValue	not-accessible	The value of a platform specific port location.
I32 juniMRoutePortMaxBw	1.3.6.1.4.1.4874.2.2.65.1.2.6.1.2	Integer32	read-write	Maximum port admission-bandwidth-limit to be configured on the port.
I32 juniMRoutePortPriorityBw	1.3.6.1.4.1.4874.2.2.65.1.2.6.1.3	Integer32	read-write	Maximum port priority-bandwidth-limit to be configured on the port.
I32 juniMRoutePortHysteresis	1.3.6.1.4.1.4874.2.2.65.1.2.6.1.4	Integer32	read-write	Hysteresis to be configured on the port. Applies to juniMRoutePortMaxBw and juniMRoutePortPriorityBw.
I32 juniMRoutePortAdmittedBw	1.3.6.1.4.1.4874.2.2.65.1.2.6.1.5	Integer32	read-only	Admitted Bandwidht on the port.
I32 juniMRoutePortSGCount	1.3.6.1.4.1.4874.2.2.65.1.2.6.1.6	Integer32	read-only	Number of mroutes on this port.
I32 juniMRoutePortLimit	1.3.6.1.4.1.4874.2.2.65.1.2.6.1.7	Integer32	read-write	Limit on the number of mroutes, with the OIFs on the port, to be configured on the port .
juniMcastNotifyObject	1.3.6.1.4.1.4874.2.2.65.1.3
juniMcastNotificationObjects	1.3.6.1.4.1.4874.2.2.65.1.3.1
NUM juniMRouteIfLocIndex	1.3.6.1.4.1.4874.2.2.65.1.3.1.1	JuniInterfaceLocationValue	accessible-for-notify	The interface location on which the mrouter trap is generated.
juniMcastConformance	1.3.6.1.4.1.4874.2.2.65.2
juniMcastCompliances	1.3.6.1.4.1.4874.2.2.65.2.1
juniMcastCompliance	1.3.6.1.4.1.4874.2.2.65.2.1.1			Obsolete compliance statement for entities which implement the Juniper multicast MIB. This statement became obsolete when juniMRouteTable were added.
juniMcastCompliance2	1.3.6.1.4.1.4874.2.2.65.2.1.2			The compliance statement for entities which implement the Juniper multicast MIB.
juniMcastCompliance3	1.3.6.1.4.1.4874.2.2.65.2.1.3			The compliance statement for entities which implement the Juniper multicast MIB.This statement became obsolete when juniMRouteInterfaceTable, juniMRoutePortTable and mrouter traps were added.
juniMcastCompliance4	1.3.6.1.4.1.4874.2.2.65.2.1.4			The compliance statement for entities which implement the Juniper multicast MIB.
juniMcastConfGroups	1.3.6.1.4.1.4874.2.2.65.2.2
juniMcastRpfRouteConfGroup	1.3.6.1.4.1.4874.2.2.65.2.2.1			A collection of objects providing management of multicast RPF static routes of the product.
juniMRouteConfGroup	1.3.6.1.4.1.4874.2.2.65.2.2.2			A collection of objects providing extended information of IP Multicast Route Entry.
juniMcastGlobalConfGroup	1.3.6.1.4.1.4874.2.2.65.2.2.3			A collection of global scalar objects providing extended information of IP Multicast Route Entry.
juniMRoutePortConfGroup	1.3.6.1.4.1.4874.2.2.65.2.2.4			A collection of objects providing extended information of IP Multicast Route Entry.

RFC description

Manages IP multicast routing configuration and statistics for Juniper router platforms.

Start monitoring Juniper Networks E-series edge router (IP multicast routing/RPF) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-MROUTER-MIB