IPV6-TUNNEL-MIB

All MIBs › IPV6-TUNNEL-MIB

Organization: QCI

Last Updated: 2011-08-31

Category: Technology: IPv6, Technology: VPN, VPN and Security

Description: QCI IPv6 tunnel MIB providing SNMP objects for managing IPv6-in-IPv4 tunnel interfaces and transition mechanism parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is IPV6-TUNNEL-MIB?

IPV6-TUNNEL-MIB is a Quanta Computer (QCI, built on QUANTA-SWITCH-MIB) proprietary MIB configuring IPv6-over-IPv4 tunnels. Its tunnel table, keyed by ID, records ifIndex, tunnel mode, local/remote IPv4 address, local ifIndex, status, and ICMP-unreachable mode, while a prefix table records the IPv6 prefix/prefix length and row status per tunnel. As a configuration MIB it lets an administrator confirm IPv6 tunnel endpoint addressing and assigned prefixes on a Quanta switch. It is deployed on Quanta Computer (QCI) switching equipment (IPv6 tunneling). Engineers can download the IPV6-TUNNEL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in IPV6-TUNNEL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Quanta Computer (QCI) switching equipment (IPv6 tunneling)

Monitoring Examples

An administrator checks agentTunnelStatus and agentTunnelIPV6PrefixPrefix to confirm an IPv6 tunnel's operational state and assigned prefix on a Quanta switch.

What Can Be Monitored

IPv6 tunnel endpoint addressing and assigned prefixes

Imported Objects

From INET-ADDRESS-MIB

InetAddressIPv4
InetAddressPrefixLength

From IPV6-TC

Ipv6Address
Ipv6AddressPrefix
Ipv6IfIndex

From QUANTA-SWITCH-MIB

switch

OBJECT-IDENTITY

From RFC1213-MIB

DisplayString
PhysAddress

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
mib-2

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
ipv6Tunnel	1.3.6.1.4.1.7244.2.27			The Quanta Private MIB for IPV6 Tunnel
agentTunnelIPV6Group	1.3.6.1.4.1.7244.2.27.1
agentTunnelIPV6Table	1.3.6.1.4.1.7244.2.27.1.1		not-accessible	A summary table of the IPV6 tunnel instances
agentTunnelIPV6Entry	1.3.6.1.4.1.7244.2.27.1.1.1		not-accessible
I32 agentTunnelID	1.3.6.1.4.1.7244.2.27.1.1.1.1	Integer32	not-accessible	The tunnel ID is associated with Internal Interface number which is generated when we create a tunnel, and is used to configure the tunnel.
I32 agentTunnelIfIndex	1.3.6.1.4.1.7244.2.27.1.1.1.2	Integer32	read-only	The external interface of the tunnel is associted with internal interface. The tunnel ID associated with Internal Interface number is generated when we create a tunnel, which is used to configure the tunnel.
INT agentTunnelMode	1.3.6.1.4.1.7244.2.27.1.1.1.3	INTEGER	read-create	Specifies the type of Tunnel either undefined, 6over4 or 6to4. The default value is undefined. It supports 6over4 which supports an assigned IPV6 address, an IPV4 address is not allowed. For this mode, the tunnel source and tunnel destination must be IPV4 address. For 6to4 tunnel, the tunnel source must be IPv4 address. Tunnel destination should not be set. The first 48-bits of the IPv4 address assigned to the 6to4 tunnel should be of the format 2002:sourceIpv4address.
ADR agentTunnelLocalIP4Addr	1.3.6.1.4.1.7244.2.27.1.1.1.4	InetAddressIPv4	read-write	The address of the Local endpoint of the tunnel i.e. the source address used in the outer IP header. It is 0.0.0.0 if unknown or the tunnel is over IPv6.
ADR agentTunnelRemoteIP4Addr	1.3.6.1.4.1.7244.2.27.1.1.1.5	InetAddressIPv4	read-write	The address of the Remote endpoint of the tunnel i.e. the destination address used in the outer IP header. It is 0.0.0.0 if the tunnel is unknown or IPv6 address, or not a point to point link
I32 agentTunnelLocalIfIndex	1.3.6.1.4.1.7244.2.27.1.1.1.6	Integer32	read-write	Specifies the interface for IPv6 Tunnel Source
ROW agentTunnelStatus	1.3.6.1.4.1.7244.2.27.1.1.1.7	RowStatus	read-create	Status of this instance.Row can be added or deleted by setting the value to createAndGo/destroy active(1) - this Tunnel instance is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance
INT agentTunnelIcmpUnreachableMode	1.3.6.1.4.1.7244.2.27.1.1.1.8	INTEGER	read-create	Specifies the Mode of Sending ICMPv6 Unreachable messages on this tunnel interface.
agentTunnelIPV6PrefixTable	1.3.6.1.4.1.7244.2.27.1.2		not-accessible	A table of the IPV6 prefixes associated with tunnel instances
agentTunnelIPV6PrefixEntry	1.3.6.1.4.1.7244.2.27.1.2.1		not-accessible
ADR agentTunnelIPV6PrefixPrefix	1.3.6.1.4.1.7244.2.27.1.2.1.1	Ipv6AddressPrefix	not-accessible	The prefix associated with the tunnel interface. The data type is used to model the IPV6 address. It is a binary string of 16 octects in network byte-order. It specifies the IP address of tunnel which will be in IPV6 Format, generated using internal interface number.
ADR agentTunnelIPV6PrefixPrefixLen	1.3.6.1.4.1.7244.2.27.1.2.1.2	InetAddressPrefixLength	not-accessible	The length of the prefix (in bits).
ROW agentTunnelIPV6PrefixStatus	1.3.6.1.4.1.7244.2.27.1.2.1.3	RowStatus	read-create	Status of this instance.Row can be added or deleted by setting the value to createAndGo/destroy active(1) - this Tunnel instance is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

RFC description

Manages IPv6 tunnel configuration and status in Quanta switches with support for tunnel mode and ICMP settings.

Start monitoring Quanta Computer (QCI) switching equipment (IPv6 tunneling) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download IPV6-TUNNEL-MIB

What Is IPV6-TUNNEL-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description