IBM-6611-APPN-MIB

All MIBs › IBM-6611-APPN-MIB

Category: SNA and Legacy Protocols

Description: Defines managed objects for IBM Advanced Peer-to-Peer Networking (APPN) nodes, including node capabilities, port information, and link station information.

IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring IBM-6611-APPN-MIB with a free 30-day trial of IPNetwork Monitor.

What Is IBM-6611-APPN-MIB?

IBM-6611-APPN-MIB defines managed objects for IBM Advanced Peer-to-Peer Networking (APPN) as implemented on IBM 6611 Network Processor devices, a technology area tied to IBM's SNA-descended peer networking architecture. It covers APPN node capabilities, port information, and link station information, describing how the node participates in the APPN network topology and how its links to other nodes are configured and behaving. Its monitoring value lies in tracking the software/protocol-level status of APPN nodes and their link stations, revealing whether inter-node links are up, degraded, or down, and whether the node's advertised capabilities match its actual configuration — useful for diagnosing SNA/APPN connectivity problems rather than raw hardware health like temperature or fans. No sample objects were available to confirm exact table names, but the MIB is closely tied to and dependent on the broader IBM APPN/SNA architecture and standard node/port/link-station conventions used across IBM networking MIBs. It is deployed on IBM 6611 Network Processors and similar IBM APPN-capable routers within legacy SNA/APPN internetworks. Engineers can download the IBM-6611-APPN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in IBM-6611-APPN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

IBM 6611 Network Processor
IBM APPN-capable router

Monitoring Examples

No concrete sample object names were provided for this module, so a specific real-object monitoring walkthrough cannot be given. Based on the description, an operator would typically monitor APPN node capability objects and per-link-station status entries to detect a link station transitioning out of an active state, which would reveal a broken inter-node APPN connection. Confirming exact table and object names would require the actual MIB source.

What Can Be Monitored

APPN node capabilities
APPN port status
link station status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
ibm	1.3.6.1.4.1.2
ibmProd	1.3.6.1.4.1.2.6
ibm6611	1.3.6.1.4.1.2.6.2
ibmappn	1.3.6.1.4.1.2.6.2.13
ibmappnNode	1.3.6.1.4.1.2.6.2.13.1
ibmappnGeneralInfoAndCaps	1.3.6.1.4.1.2.6.2.13.1.1
STR ibmappnNodeCpName	1.3.6.1.4.1.2.6.2.13.1.1.1	DisplayString	read-only	Administratively-assigned network name for this node in the format NETID.CPNAME.
STR ibmappnNodeNetid	1.3.6.1.4.1.2.6.2.13.1.1.2	DisplayString	read-only	Administratively-assigned APPN network identification, which can be from one to eight characters. This ID is used with the control point name to create a fully-qualified control point name.
STR ibmappnNodeBlockNum	1.3.6.1.4.1.2.6.2.13.1.1.3	DisplayString	read-only	The block number is the first three digits of the node_id. These 3 hexadecimal digits identify the product and are not configurable.
STR ibmappnNodeIdNum	1.3.6.1.4.1.2.6.2.13.1.1.4	DisplayString	read-only	The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are administratively defined and combined with the 3 digit block number form the node_id. This node_id is used to identify the local node and is include in APPN alerts as well as being included in XIDs. A unique value is required for connections to SNA sub-area.
INT ibmappnNodeType	1.3.6.1.4.1.2.6.2.13.1.1.5	INTEGER	read-only	Type of APPN node, either network, len, or end node.
TIK ibmappnNodeUpTime	1.3.6.1.4.1.2.6.2.13.1.1.6	TimeTicks	read-only	Time (in hundredths of a second) since this APPN node was initialized.
INT ibmappnNodeNegotLs	1.3.6.1.4.1.2.6.2.13.1.1.7	INTEGER	read-only	Indicates whether this node supports negotiable link stations.
INT ibmappnNodeSegReasm	1.3.6.1.4.1.2.6.2.13.1.1.8	INTEGER	read-only	Indicates whether this node supports segment reassembly. This is only supported when segment generation is also supported.
INT ibmappnNodeBindReasm	1.3.6.1.4.1.2.6.2.13.1.1.9	INTEGER	read-only	Indicates whether this node supports Bind segment reassembly. This will only be supported when Bind segment generation is also supported.
INT ibmappnNodeParallelTg	1.3.6.1.4.1.2.6.2.13.1.1.10	INTEGER	read-only	Indicates whether this node supports parallel TGs.
INT ibmappnNodeService	1.3.6.1.4.1.2.6.2.13.1.1.11	INTEGER	read-only	Indicates whether this node allows call-in from nodes not defined locally.
INT ibmappnNodeAdaptiveBindPacing	1.3.6.1.4.1.2.6.2.13.1.1.12	INTEGER	read-only	Indicates whether this node supports adaptive bind pacing.
ibmappnNnUniqueInfoAndCaps	1.3.6.1.4.1.2.6.2.13.1.2
INT ibmappnNodeNnRcvRegChar	1.3.6.1.4.1.2.6.2.13.1.2.1	INTEGER	read-only	Indicates whether this node supports receiving registered characteristics.
INT ibmappnNodeNnGateway	1.3.6.1.4.1.2.6.2.13.1.2.2	INTEGER	read-only	Indicates whether this is a gateway node.
INT ibmappnNodeNnCentralDirectory	1.3.6.1.4.1.2.6.2.13.1.2.3	INTEGER	read-only	Indicates whether this node supports central directory cache.
INT ibmappnNodeNnTreeCache	1.3.6.1.4.1.2.6.2.13.1.2.4	INTEGER	read-only	Indicates whether this node supports route tree cache.
INT ibmappnNodeNnTreeUpdate	1.3.6.1.4.1.2.6.2.13.1.2.5	INTEGER	read-only	Indicates whether this node supports incremental_tree_update, which is only supported when tree caching is supported.
INT ibmappnNodeNnRouteAddResist	1.3.6.1.4.1.2.6.2.13.1.2.6	INTEGER	read-only	Route addition resistance is a value that indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing.
INT ibmappnNodeNnIsr	1.3.6.1.4.1.2.6.2.13.1.2.7	INTEGER	read-only	Indicates whether the node supports intermediate session routing.
INT ibmappnNodeNnFrsn	1.3.6.1.4.1.2.6.2.13.1.2.8	INTEGER	read-only	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This object is the last FRSN sent in a topology update to adjacent network nodes.
ibmappnEnUniqueCaps	1.3.6.1.4.1.2.6.2.13.1.3
INT ibmappnNodeEnSegGen	1.3.6.1.4.1.2.6.2.13.1.3.1	INTEGER	read-only	Indicates whether this end node supports segment generation.
INT ibmappnNodeEnModeCosMap	1.3.6.1.4.1.2.6.2.13.1.3.2	INTEGER	read-only	Indicates whether this end node supports mode name to COS name mapping.
INT ibmappnNodeEnLocateCdinit	1.3.6.1.4.1.2.6.2.13.1.3.3	INTEGER	read-only	Indicates whether this end node supports Locate Cdinit.
INT ibmappnNodeEnSendRegNames	1.3.6.1.4.1.2.6.2.13.1.3.4	INTEGER	read-only	Indicates whether the node will register its LUs with the adjacent serving network node: NO - do not register names YES - register names
INT ibmappnNodeEnSendRegChar	1.3.6.1.4.1.2.6.2.13.1.3.5	INTEGER	read-only	Indicates whether this node supports send register characteristics, which is only supported when send registered names is also supported.
ibmappnPortInformation	1.3.6.1.4.1.2.6.2.13.1.4
ibmappnNodePortTable	1.3.6.1.4.1.2.6.2.13.1.4.1		not-accessible	The Port table describes the configuration and current status of the ports used by APPN. The type of DLC is included in this table as a pointer to the DLC port specific tables.
ibmappnNodePortEntry	1.3.6.1.4.1.2.6.2.13.1.4.1.1		not-accessible	The Port Name is used as the index to this table.
STR ibmappnNodePortName	1.3.6.1.4.1.2.6.2.13.1.4.1.1.1	DisplayString	read-only	Administratively-assigned name for this APPN port. The name can be from one to eight characters.
INT ibmappnNodePortState	1.3.6.1.4.1.2.6.2.13.1.4.1.1.2	INTEGER	read-only	Indicates the current state of this port.
INT ibmappnNodePortDlcType	1.3.6.1.4.1.2.6.2.13.1.4.1.1.3	INTEGER	read-only	The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
INT ibmappnNodePortPortType	1.3.6.1.4.1.2.6.2.13.1.4.1.1.4	INTEGER	read-only	Identifies the type of line used by this port.
INT ibmappnNodePortSIMRIM	1.3.6.1.4.1.2.6.2.13.1.4.1.1.5	INTEGER	read-only	Indicates whether Set Initialization Mode (SIM) and Receive Initialization Mode (RIM) are supported.
INT ibmappnNodePortLsRole	1.3.6.1.4.1.2.6.2.13.1.4.1.1.6	INTEGER	read-only	Initial role for LSs activated through this port, where 'abm' indicates asynchronous balance mode.
INT ibmappnNodePortMaxRcvBtuSize	1.3.6.1.4.1.2.6.2.13.1.4.1.1.7	INTEGER	read-only	Maximum Basic Transmission Size (BTU) that a link station on this port can receive.
INT ibmappnNodePortMaxIframeWindow	1.3.6.1.4.1.2.6.2.13.1.4.1.1.8	INTEGER	read-only	Maximum number of I-frames that can be received by the XID sender before an acknowledgement is received.
CTR ibmappnNodePortDefLsGoodXids	1.3.6.1.4.1.2.6.2.13.1.4.1.1.9	Counter	read-only	The total number of successful XIDs that have occurred on all defined link stations on this port since the last time this port was started.
CTR ibmappnNodePortDefLsBadXids	1.3.6.1.4.1.2.6.2.13.1.4.1.1.10	Counter	read-only	The total number of unsuccessful XIDs that have occurred on all defined link stations on this port since the last time this port was started.
CTR ibmappnNodePortDynLsGoodXids	1.3.6.1.4.1.2.6.2.13.1.4.1.1.11	Counter	read-only	The total number of successful XIDs that have occurred on all dynamic link stations on this port since the last time this port was started.
CTR ibmappnNodePortDynLsBadXids	1.3.6.1.4.1.2.6.2.13.1.4.1.1.12	Counter	read-only	The total number of unsuccessful XIDs that have occurred on all dynamic link stations on this port since the last time this port was started.
OID ibmappnNodePortSpecific	1.3.6.1.4.1.2.6.2.13.1.4.1.1.13	OBJECT IDENTIFIER	read-only	Identifies the port specific OBJECT IDENTIFIER that can provide additional information.
ibmappnNodePortIpTable	1.3.6.1.4.1.2.6.2.13.1.4.2		not-accessible	Port table (TCP/IP specific).
ibmappnNodePortIpEntry	1.3.6.1.4.1.2.6.2.13.1.4.2.1		not-accessible	The IP Name is used as the index to this table.
STR ibmappnNodePortIpName	1.3.6.1.4.1.2.6.2.13.1.4.2.1.1	DisplayString	read-only	Administratively-assigned name for this APPN port. The name can be from one to eight characters.
INT ibmappnNodePortIpPortNum	1.3.6.1.4.1.2.6.2.13.1.4.2.1.2	INTEGER	read-only	Local TCP/IP port number.
ibmappnNodePortDlsTable	1.3.6.1.4.1.2.6.2.13.1.4.3		not-accessible	Port table (DLS specific).
ibmappnNodePortDlsEntry	1.3.6.1.4.1.2.6.2.13.1.4.3.1		not-accessible	The DLS Name is used as the index to this table.
STR ibmappnNodePortDlsName	1.3.6.1.4.1.2.6.2.13.1.4.3.1.1	DisplayString	read-only	Administratively-assigned name for this APPN DLS port. The name can be from one to eight characters.
OCT ibmappnNodePortDlsMac	1.3.6.1.4.1.2.6.2.13.1.4.3.1.2	OCTET STRING	read-only	Local DLS MAC address.
OCT ibmappnNodePortDlsSap	1.3.6.1.4.1.2.6.2.13.1.4.3.1.3	OCTET STRING	read-only	Local DLS Sap address.
ibmappnNodePortTrTable	1.3.6.1.4.1.2.6.2.13.1.4.4		not-accessible	Port table (Token Ring specific).
ibmappnNodePortTrEntry	1.3.6.1.4.1.2.6.2.13.1.4.4.1		not-accessible	The TR Name is used as the index to this table.
STR ibmappnNodePortTrName	1.3.6.1.4.1.2.6.2.13.1.4.4.1.1	DisplayString	read-only	Administratively-assigned name for this APPN port. The name can be from one to eight characters.
OCT ibmappnNodePortTrMac	1.3.6.1.4.1.2.6.2.13.1.4.4.1.2	OCTET STRING	read-only	Local Token Ring MAC address.
OCT ibmappnNodePortTrSap	1.3.6.1.4.1.2.6.2.13.1.4.4.1.3	OCTET STRING	read-only	Local Token Ring Sap address.
ibmappnNodePortDlcTraceTable	1.3.6.1.4.1.2.6.2.13.1.4.5		not-accessible	Port table generic DLC trace table.
ibmappnNodePortDlcTraceEntry	1.3.6.1.4.1.2.6.2.13.1.4.5.1		not-accessible	The Port name and a dynamic integer are the index to this table.
STR ibmappnNodePortDlcTracPortName	1.3.6.1.4.1.2.6.2.13.1.4.5.1.1	DisplayString	read-only	The Port name associated with this this trace table entry.
INT ibmappnNodePortDlcTracIndex	1.3.6.1.4.1.2.6.2.13.1.4.5.1.2	INTEGER	read-only	This index value is updated every time a new trace entry is created which provides a means to retrieve only the updated entries and also provides a simple method of correlating the entries. The table will wrap when the table is full, which will result in previous entries being written over. The mangement station can over come this by retrieving the table using this index to retrieve only the new table entries.
INT ibmappnNodePortDlcTracDlcType	1.3.6.1.4.1.2.6.2.13.1.4.5.1.3	INTEGER	read-only	The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
STR ibmappnNodePortDlcTracLocalAddr	1.3.6.1.4.1.2.6.2.13.1.4.5.1.4	DisplayString	read-only	Local address in format described below: other = free form DisplayString ip = ld.ld.ld.ld/2d tr = lx:lx:lx:lx:lx:lx.lx dlsw = lx:lx:lx:lx:lx:lx.lx ethernet = lx:lx:lx:lx:lx:lx.lx
STR ibmappnNodePortDlcTracRemoteAddr	1.3.6.1.4.1.2.6.2.13.1.4.5.1.5	DisplayString	read-only	Remote Address in the format described below: other = free form DisplayString ip = ld.ld.ld.ld/2d tr = lx:lx:lx:lx:lx:lx.lx dlsw = lx:lx:lx:lx:lx:lx.lx ethernet = lx:lx:lx:lx:lx:lx.lx
INT ibmappnNodePortDlcTracMsgType	1.3.6.1.4.1.2.6.2.13.1.4.5.1.6	INTEGER	read-only	Indicates the type of trace record entry
INT ibmappnNodePortDlcTracCmdType	1.3.6.1.4.1.2.6.2.13.1.4.5.1.7	INTEGER	read-only	Indicates the command type of the trace entry.
INT ibmappnNodePortDlcTracUseWan	1.3.6.1.4.1.2.6.2.13.1.4.5.1.8	INTEGER	read-only
ibmappnLinkStationInformation	1.3.6.1.4.1.2.6.2.13.1.5
ibmappnNodeLsTable	1.3.6.1.4.1.2.6.2.13.1.5.1		not-accessible	This table contains detail information about the link station configuration and current status.
ibmappnNodeLsEntry	1.3.6.1.4.1.2.6.2.13.1.5.1.1		not-accessible	This table is indexed by the link station name.
STR ibmappnNodeLsName	1.3.6.1.4.1.2.6.2.13.1.5.1.1.1	DisplayString	read-only	Administratively-assigned name for the link station. The name can be from one to eight characters.
STR ibmappnNodeLsPortName	1.3.6.1.4.1.2.6.2.13.1.5.1.1.2	DisplayString	read-only	Administratively-assigned name for the port. The name can be from one to eight characters.
INT ibmappnNodeLsDlcType	1.3.6.1.4.1.2.6.2.13.1.5.1.1.3	INTEGER	read-only	The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
INT ibmappnNodeLsDynamic	1.3.6.1.4.1.2.6.2.13.1.5.1.1.4	INTEGER	read-only	Identifies whether this resource is a dynamic link station. Dynamic link stations are created when adjacent nodes that have not been locally defined establish a connection with this node.
INT ibmappnNodeLsState	1.3.6.1.4.1.2.6.2.13.1.5.1.1.5	INTEGER	read-only	State of this link station.
STR ibmappnNodeLsCpName	1.3.6.1.4.1.2.6.2.13.1.5.1.1.6	DisplayString	read-only	Fully-qualified name of the adjacent node for this link station. The name can be from three to seventeen characters. Format is netid.cpname.
INT ibmappnNodeLsTgNum	1.3.6.1.4.1.2.6.2.13.1.5.1.1.7	INTEGER	read-only	Number associated with the TG to this link station.
INT ibmappnNodeLsLimResource	1.3.6.1.4.1.2.6.2.13.1.5.1.1.8	INTEGER	read-only	Indicates whether the link station is a limited resource. If it is, the TG is deactivated when there are no sessions.
INT ibmappnNodeLsMigration	1.3.6.1.4.1.2.6.2.13.1.5.1.1.9	INTEGER	read-only	Indicates whether this link station will be used for connections to down-level or migration partners.
STR ibmappnNodeLsBlockNum	1.3.6.1.4.1.2.6.2.13.1.5.1.1.10	DisplayString	read-only	The block number is the first three digits of the node_id. These 3 hexidecimal digits identify the product and are not configurable.
STR ibmappnNodeLsIdNum	1.3.6.1.4.1.2.6.2.13.1.5.1.1.11	DisplayString	read-only	The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are administratively defined and combined with the 3 digit block number form the node_id. This node_id is used to identify the local node and is include in APPN alerts as well as being included in XIDs. A unique value is required for connections to SNA sub-area.
INT ibmappnNodeLsCpCpSession	1.3.6.1.4.1.2.6.2.13.1.5.1.1.12	INTEGER	read-only	Indicates whether CP-CP sessions are supported by this link station.
INT ibmappnNodeLsTargetPacingCount	1.3.6.1.4.1.2.6.2.13.1.5.1.1.13	INTEGER	read-only	Numeric value between 0 and 32767 inclusive indicating the desired pacing window size for BINDs on this TG. The number is significant only when fixed bind pacing is being performed.
INT ibmappnNodeLsMaxSendBtuSize	1.3.6.1.4.1.2.6.2.13.1.5.1.1.14	INTEGER	read-only	Numeric value between 0 and 32767 inclusive indicating the desired number of bytes in a Basic Transmission Unit (BTU) that can be sent on this TG. This is an administratively assigned value.
INT ibmappnNodeLsEffCap	1.3.6.1.4.1.2.6.2.13.1.5.1.1.15	INTEGER	read-only	The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with the TG using this link station.
INT ibmappnNodeLsConnCost	1.3.6.1.4.1.2.6.2.13.1.5.1.1.16	INTEGER	read-only	Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated with the TG using this link station.
INT ibmappnNodeLsByteCost	1.3.6.1.4.1.2.6.2.13.1.5.1.1.17	INTEGER	read-only	Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with the TG using this link station.
INT ibmappnNodeLsSecurity	1.3.6.1.4.1.2.6.2.13.1.5.1.1.18	INTEGER	read-only	The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with the TG using this link station.
INT ibmappnNodeLsDelay	1.3.6.1.4.1.2.6.2.13.1.5.1.1.19	INTEGER	read-only	Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with the TG using this link station.
INT ibmappnNodeLsUsr1	1.3.6.1.4.1.2.6.2.13.1.5.1.1.20	INTEGER	read-only	First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station.
INT ibmappnNodeLsUsr2	1.3.6.1.4.1.2.6.2.13.1.5.1.1.21	INTEGER	read-only	Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station.
INT ibmappnNodeLsUsr3	1.3.6.1.4.1.2.6.2.13.1.5.1.1.22	INTEGER	read-only	Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station.
CTR ibmappnNodeLsInXidBytes	1.3.6.1.4.1.2.6.2.13.1.5.1.1.23	Counter	read-only	Number of XID bytes received.
CTR ibmappnNodeLsInMsgBytes	1.3.6.1.4.1.2.6.2.13.1.5.1.1.24	Counter	read-only	Number of message (I-frame) bytes received.
CTR ibmappnNodeLsInXidFrames	1.3.6.1.4.1.2.6.2.13.1.5.1.1.25	Counter	read-only	Number of XID frames received.
CTR ibmappnNodeLsInMsgFrames	1.3.6.1.4.1.2.6.2.13.1.5.1.1.26	Counter	read-only	Number of message (I-frame) frames received.
CTR ibmappnNodeLsOutXidBytes	1.3.6.1.4.1.2.6.2.13.1.5.1.1.27	Counter	read-only	Number of XID bytes sent.
CTR ibmappnNodeLsOutMsgBytes	1.3.6.1.4.1.2.6.2.13.1.5.1.1.28	Counter	read-only	Number of message (I-frame) bytes sent.
CTR ibmappnNodeLsOutXidFrames	1.3.6.1.4.1.2.6.2.13.1.5.1.1.29	Counter	read-only	Number of XID frames sent.
CTR ibmappnNodeLsOutMsgFrames	1.3.6.1.4.1.2.6.2.13.1.5.1.1.30	Counter	read-only	Number of message (I-frame) frames sent.
CTR ibmappnNodeLsEchoRsps	1.3.6.1.4.1.2.6.2.13.1.5.1.1.31	Counter	read-only	Number of responses returned from adjacent link station. A response should be returned for each test frame sent by this node. Test frames are sent to adjacent nodes periodically to verify connectivity and to measure that actual round trip time, that is the time the test frame is sent until the response is received.
INT ibmappnNodeLsCurrentDelay	1.3.6.1.4.1.2.6.2.13.1.5.1.1.32	INTEGER	read-only	The time that it took for the last test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds.
INT ibmappnNodeLsMaxDelay	1.3.6.1.4.1.2.6.2.13.1.5.1.1.33	INTEGER	read-only	The longest time it took for a test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds .
INT ibmappnNodeLsMinDelay	1.3.6.1.4.1.2.6.2.13.1.5.1.1.34	INTEGER	read-only	The shortest time it took for a test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds.
TIK ibmappnNodeLsMaxDelayTime	1.3.6.1.4.1.2.6.2.13.1.5.1.1.35	TimeTicks	read-only	The time (since system up in hundredth of seconds) when the longest delay occurred. This time can be used to identify when this high water mark occurred in relation to the last initialization of the APPN node.
CTR ibmappnNodeLsGoodXids	1.3.6.1.4.1.2.6.2.13.1.5.1.1.36	Counter	read-only	The total number of successful XIDs that have occurred on this link station since the time it was started.
CTR ibmappnNodeLsBadXids	1.3.6.1.4.1.2.6.2.13.1.5.1.1.37	Counter	read-only	The total number of unsuccessful XIDs that have occurred on this link station since the time it was started.
OID ibmappnNodeLsSpecific	1.3.6.1.4.1.2.6.2.13.1.5.1.1.38	OBJECT IDENTIFIER	read-only	Identifies the DLC specific OBJECT IDENTIFIER that can provide additional information.
INT ibmappnNodeLsSubState	1.3.6.1.4.1.2.6.2.13.1.5.1.1.39	INTEGER	read-only	State of this link station.
TIK ibmappnNodeLsStartTime	1.3.6.1.4.1.2.6.2.13.1.5.1.1.40	TimeTicks	read-only	The time (in hundredth of seconds) this link station has been active the last time since the time APPN was initialized.
TIK ibmappnNodeLsActiveTime	1.3.6.1.4.1.2.6.2.13.1.5.1.1.41	TimeTicks	read-only	The time (in hundredth of seconds) this link station has been in the active state. A zero value indicates the link station has never been active.
TIK ibmappnNodeLsCurrentStateTime	1.3.6.1.4.1.2.6.2.13.1.5.1.1.42	TimeTicks	read-only	The time (in hundredth of seconds) the link station is in the current state.
ibmappnNodeLsIpTable	1.3.6.1.4.1.2.6.2.13.1.5.2		not-accessible	Link station table (TCP/IP specific).
ibmappnNodeLsIpEntry	1.3.6.1.4.1.2.6.2.13.1.5.2.1		not-accessible	The IP Name is used as the index to this table.
STR ibmappnNodeLsIpName	1.3.6.1.4.1.2.6.2.13.1.5.2.1.1	DisplayString	read-only	Administratively-assigned name for this link station. The name can be from one to eight characters.
INT ibmappnNodeLsIpState	1.3.6.1.4.1.2.6.2.13.1.5.2.1.2	INTEGER	read-only	State of this link station.
IP ibmappnNodeLsLocalIpAddr	1.3.6.1.4.1.2.6.2.13.1.5.2.1.3	IpAddress	read-only	Local IP address.
INT ibmappnNodeLsLocalIpPortNum	1.3.6.1.4.1.2.6.2.13.1.5.2.1.4	INTEGER	read-only	Local TCP/IP port number. The default listening port will be administratively assigned and will dynamically change if this node initiates a session with adjacent node.
IP ibmappnNodeLsRemoteIpAddr	1.3.6.1.4.1.2.6.2.13.1.5.2.1.5	IpAddress	read-only	Remote IP address.
INT ibmappnNodeLsRemoteIpPortNum	1.3.6.1.4.1.2.6.2.13.1.5.2.1.6	INTEGER	read-only	Remote TCP/IP port number.
ibmappnNodeLsDlsTable	1.3.6.1.4.1.2.6.2.13.1.5.3		not-accessible	Ls Table (DLS specific).
ibmappnNodeLsDlsEntry	1.3.6.1.4.1.2.6.2.13.1.5.3.1		not-accessible	The DLS Name is used as the index to this table.
STR ibmappnNodeLsDlsName	1.3.6.1.4.1.2.6.2.13.1.5.3.1.1	DisplayString	read-only	Administratively-assigned name for this link station. The name can be from one to eight characters.
INT ibmappnNodeLsDlsState	1.3.6.1.4.1.2.6.2.13.1.5.3.1.2	INTEGER	read-only	State of this link station.
OCT ibmappnNodeLsLocalDlsMac	1.3.6.1.4.1.2.6.2.13.1.5.3.1.3	OCTET STRING	read-only	Local MAC address.
OCT ibmappnNodeLsLocalDlsSap	1.3.6.1.4.1.2.6.2.13.1.5.3.1.4	OCTET STRING	read-only	Local SAP address.
OCT ibmappnNodeLsRemoteDlsMac	1.3.6.1.4.1.2.6.2.13.1.5.3.1.5	OCTET STRING	read-only	Remote MAC address.
OCT ibmappnNodeLsRemoteDlsSap	1.3.6.1.4.1.2.6.2.13.1.5.3.1.6	OCTET STRING	read-only	Remote SAP address.
ibmappnNodeLsTrTable	1.3.6.1.4.1.2.6.2.13.1.5.4		not-accessible	Ls Table (Token Ring specific).
ibmappnNodeLsTrEntry	1.3.6.1.4.1.2.6.2.13.1.5.4.1		not-accessible	The TR Name is used as the index to this table.
STR ibmappnNodeLsTrName	1.3.6.1.4.1.2.6.2.13.1.5.4.1.1	DisplayString	read-only	Administratively-assigned name for this link station. The name can be from one to eight characters.
INT ibmappnNodeLsTrState	1.3.6.1.4.1.2.6.2.13.1.5.4.1.2	INTEGER	read-only	State of this link station.
OCT ibmappnNodeLsLocalTrMac	1.3.6.1.4.1.2.6.2.13.1.5.4.1.3	OCTET STRING	read-only	Local MAC address.
OCT ibmappnNodeLsLocalTrSap	1.3.6.1.4.1.2.6.2.13.1.5.4.1.4	OCTET STRING	read-only	Local SAP address.
OCT ibmappnNodeLsRemoteTrMac	1.3.6.1.4.1.2.6.2.13.1.5.4.1.5	OCTET STRING	read-only	Remote MAC address.
OCT ibmappnNodeLsRemoteTrSap	1.3.6.1.4.1.2.6.2.13.1.5.4.1.6	OCTET STRING	read-only	Remote SAP address.
ibmappnNodeLsStatusTable	1.3.6.1.4.1.2.6.2.13.1.5.5		not-accessible	This table contains information related to exceptional and potential exceptional conditions that occur during the activation, XID exchange, and termination of the connection.
ibmappnNodeLsStatusEntry	1.3.6.1.4.1.2.6.2.13.1.5.5.1		not-accessible	This table is indexed by the LsStatusIndex, which is an integer that is continuously updated until it eventually wraps. This provides the management station the ability to retrieve only the updates to the table by using the standard GET NEXT.
INT ibmappnNodeLsStatusIndex	1.3.6.1.4.1.2.6.2.13.1.5.5.1.1	INTEGER	read-only	Table index. The value of the index begins at zero and is incremented up to a maximum value of 2**31-1 (2,147,483,647) before wrapping.
TIK ibmappnNodeLsStatusTime	1.3.6.1.4.1.2.6.2.13.1.5.5.1.2	TimeTicks	read-only	Time (in hundreds of a second) since this node was last initialized.
STR ibmappnNodeLsStatusLsName	1.3.6.1.4.1.2.6.2.13.1.5.5.1.3	DisplayString	read-only	Administratively-assigned name for this link station.
STR ibmappnNodeLsStatusCpName	1.3.6.1.4.1.2.6.2.13.1.5.5.1.4	DisplayString	read-only	Administratively-assigned fully-qualified name of the adjacent node partner. This will be provided when the adjacent node has been defined at this node or when the XID sequence has proceeded far enough to to identify the adjacent node. A blank CP name will indicate the name is unknown.
OCT ibmappnNodeLsStatusNodeId	1.3.6.1.4.1.2.6.2.13.1.5.5.1.5	OCTET STRING	read-only	Adjacent Node id
INT ibmappnNodeLsStatusTgNum	1.3.6.1.4.1.2.6.2.13.1.5.5.1.6	INTEGER	read-only	Number associated with the TG to this link station with a range from 0 to 256. A value of 256 indicates the tg number has not been negotiated and is unknown at this time.
OCT ibmappnNodeLsStatusGeneralSense	1.3.6.1.4.1.2.6.2.13.1.5.5.1.7	OCTET STRING	read-only	The error sense code associated with the start sequence of activation of a link up to the beginning of the XID sequence.
INT ibmappnNodeLsStatusNofRetry	1.3.6.1.4.1.2.6.2.13.1.5.5.1.8	INTEGER	read-only	Indicates whether NOF will retry the start request to activate the link.
OCT ibmappnNodeLsStatusEndSense	1.3.6.1.4.1.2.6.2.13.1.5.5.1.9	OCTET STRING	read-only	The sense code associated with the termination of the link connection to adjacent node. This includes all sense information included in the disconnect received from the lower layer DLCs and also sense information indicating the link termination originated by upper layer APPN components.
OCT ibmappnNodeLsStatusXidLocalSense	1.3.6.1.4.1.2.6.2.13.1.5.5.1.10	OCTET STRING	read-only	The error sense code associated with the rejection of the XID.
OCT ibmappnNodeLsStatusXidRemoteSense	1.3.6.1.4.1.2.6.2.13.1.5.5.1.11	OCTET STRING	read-only	The error sense code adjacent node returned to this node indicating the reason the XID was rejected.
INT ibmappnNodeLsStatusXidByteInError	1.3.6.1.4.1.2.6.2.13.1.5.5.1.12	INTEGER	read-only	This identifies the actual byte in the XID that caused the error. The value of zero (0) indicates that the variable has no meaning.
INT ibmappnNodeLsStatusXidBitInError	1.3.6.1.4.1.2.6.2.13.1.5.5.1.13	INTEGER	read-only	This identifies the actual bit within the error byte of the XID. This only has meaning when the byte in error is greater than zero.
INT ibmappnNodeLsStatusDlcType	1.3.6.1.4.1.2.6.2.13.1.5.5.1.14	INTEGER	read-only	This identifies DLC type that was being used when error occurred. This also is used to the format of the local and remote address provided. other = free form DisplayString ip = ld.ld.ld.ld/2d tr = lx:lx:lx:lx:lx:lx.lx dlsw = lx:lx:lx:lx:lx:lx.lx ethernet = lx:lx:lx:lx:lx:lx.lx
STR ibmappnNodeLsStatusLocalAddr	1.3.6.1.4.1.2.6.2.13.1.5.5.1.15	DisplayString	read-only	This contains a displayable string that identifies the DLC type and appropriate address. See DlcType above for details of the format.
STR ibmappnNodeLsStatusRemoteAddr	1.3.6.1.4.1.2.6.2.13.1.5.5.1.16	DisplayString	read-only	This contains a displayable string that identifies the DLC type and appropriate address. See DlcType above for details of the format.
ibmappnSnmpInformation	1.3.6.1.4.1.2.6.2.13.1.6
CTR ibmappnSnmpInPkts	1.3.6.1.4.1.2.6.2.13.1.6.1	Counter	read-only	Total number of messages delivered to the APPN SNMP sub-agent.
CTR ibmappnSnmpInGetRequests	1.3.6.1.4.1.2.6.2.13.1.6.2	Counter	read-only	Total number of GET requests delivered to the APPN SNMP sub-agent.
CTR ibmappnSnmpInGetNexts	1.3.6.1.4.1.2.6.2.13.1.6.3	Counter	read-only	Total number of GETNEXT requests delivered to the APPN SNMP sub-agent.
CTR ibmappnSnmpInSetRequests	1.3.6.1.4.1.2.6.2.13.1.6.4	Counter	read-only	Total number of SET requests delivered to the APPN SNMP sub-agent.
CTR ibmappnSnmpInTotalVars	1.3.6.1.4.1.2.6.2.13.1.6.5	Counter	read-only	Total number of VARIABLES included in both GET and GETNEXT requests to the APPN SNMP sub-agent.
CTR ibmappnSnmpInGetVars	1.3.6.1.4.1.2.6.2.13.1.6.6	Counter	read-only	Total number of VARIABLES included in all GET requests to the APPN SNMP sub-agent.
CTR ibmappnSnmpInGetNextVars	1.3.6.1.4.1.2.6.2.13.1.6.7	Counter	read-only	Total number of VARIABLES included in all GETNEXT requests to the APPN SNMP sub-agent.
CTR ibmappnSnmpInSetVars	1.3.6.1.4.1.2.6.2.13.1.6.8	Counter	read-only	Total number of VARIABLES included in all SET requests to the APPN SNMP sub-agent.
CTR ibmappnSnmpOutNoSuchNames	1.3.6.1.4.1.2.6.2.13.1.6.9	Counter	read-only	Total number of VARIABLES that could not be found by the APPN SNMP sub-agent.
CTR ibmappnSnmpOutGenErrs	1.3.6.1.4.1.2.6.2.13.1.6.10	Counter	read-only	Total number of undefined errors that occurred processing SNMP request to the APPN SNMP sub-agent.
ibmappnMemoryUse	1.3.6.1.4.1.2.6.2.13.1.7
INT ibmappnMemorySize	1.3.6.1.4.1.2.6.2.13.1.7.1	INTEGER	read-only	Size of the shared storage segment, as obtained by storage management from the underlying operating system.
INT ibmappnMemoryUsed	1.3.6.1.4.1.2.6.2.13.1.7.2	INTEGER	read-only	Number of bytes in the segment that are currently allocated to process.
INT ibmappnMemoryWarnThresh	1.3.6.1.4.1.2.6.2.13.1.7.3	INTEGER	read-only	Allocation threshold beyond which storage management considers the storage resources to be constrained.
INT ibmappnMemoryCritThresh	1.3.6.1.4.1.2.6.2.13.1.7.4	INTEGER	read-only	Allocation threshold beyond which storage management considers the storage resources to be critically constrained.
ibmappnXidInformation	1.3.6.1.4.1.2.6.2.13.1.8
CTR ibmappnNodeDefLsGoodXids	1.3.6.1.4.1.2.6.2.13.1.8.1	Counter	read-only	The current number of successful XIDs that have occurred on all defined link stations since the last time this node was initialized.
CTR ibmappnNodeDefLsBadXids	1.3.6.1.4.1.2.6.2.13.1.8.2	Counter	read-only	The current number of unsuccessful XIDs that have occurred on all defined link stations since the last time this node was initialized.
CTR ibmappnNodeDynLsGoodXids	1.3.6.1.4.1.2.6.2.13.1.8.3	Counter	read-only	The current number of successful XIDs that have occurred on all dynamic link stations since the last time this node was initialized.
CTR ibmappnNodeDynLsBadXids	1.3.6.1.4.1.2.6.2.13.1.8.4	Counter	read-only	The current number of unsuccessful XIDs that have occurred on all dynamic link stations since the last time this node was initialized.
ibmappnNn	1.3.6.1.4.1.2.6.2.13.2
ibmappnNnTopo	1.3.6.1.4.1.2.6.2.13.2.1
INT ibmappnNnTopoMaxNodes	1.3.6.1.4.1.2.6.2.13.2.1.1	INTEGER	read-only	Maximum number of nodes allowed in the APPN topology database This administratively assigned value must be equal to or greater than the maximum total number of end nodes and network nodes. If the number of nodes exceeds this value, APPN will issue an Alert and the node can no longer participate as a network node.
GAU ibmappnNnTopoCurNumNodes	1.3.6.1.4.1.2.6.2.13.2.1.2	Gauge	read-only	Current number of nodes in this node's topology database. If this value exceeds the maximum number of nodes allowed (NnTopoMaxNodes), APPN alert CPDB002 is issued.
CTR ibmappnNnTopoInTdus	1.3.6.1.4.1.2.6.2.13.2.1.3	Counter	read-only	Total number of TDUs received from all adjacent NN since last initialization.
CTR ibmappnNnTopoOutTdus	1.3.6.1.4.1.2.6.2.13.2.1.4	Counter	read-only	Total number of TDUs built by this node to be sent to all adjacent NN since last initialization.
CTR ibmappnNnTopoNodeLowRsns	1.3.6.1.4.1.2.6.2.13.2.1.5	Counter	read-only	Total number of topology node updates received by this node with a RSN less than the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs, but this node will send a TDU with it's higher RSN to the adjacent node that sent this low RSN.
CTR ibmappnNnTopoNodeEqualRsns	1.3.6.1.4.1.2.6.2.13.2.1.6	Counter	read-only	Total number of topology node updates received by this node with a RSN equal to the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs.
CTR ibmappnNnTopoNodeGoodHighRsns	1.3.6.1.4.1.2.6.2.13.2.1.7	Counter	read-only	Total number of topology node updates received by this node with a RSN greater than the current RSN. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes. It is not required to send a TDU to the sender of this update because that node already has the update.
CTR ibmappnNnTopoNodeBadHighRsns	1.3.6.1.4.1.2.6.2.13.2.1.8	Counter	read-only	Total number of topology node updates received by this node with an odd RSN greater than the current RSN. These updates represent a topology inconsistency detected by one of the APPN network nodes. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes.
CTR ibmappnNnTopoNodeStateUpdates	1.3.6.1.4.1.2.6.2.13.2.1.9	Counter	read-only	Total number of topology Node records built as a result of internally detected node state changes that affect APPN topology and routing. Updates are sent via TDUs to all adjacent network nodes.
CTR ibmappnNnTopoNodeErrors	1.3.6.1.4.1.2.6.2.13.2.1.10	Counter	read-only	Total number of topology node records inconsistencies detected by this node. This occurs when this node attempts to update its topology database and detects a data inconsistency. This node will create a TDU with the current RSN incremented to the next odd number and broadcast it to all adjacent NNs.
CTR ibmappnNnTopoNodeTimerUpdates	1.3.6.1.4.1.2.6.2.13.2.1.11	Counter	read-only	Total number of topology node records built for this node's resource due to timer updates. Updates are sent via TDUs to all adjacent network nodes. These updates insure other network nodes do not delete this node's resources from their topology database.
CTR ibmappnNnTopoNodePurges	1.3.6.1.4.1.2.6.2.13.2.1.12	Counter	read-only	Total number of topology node records purged from this node's topology database. This occurs when a node has not been updated in a specified amount of time. The owning node is responsible for broadcasting updates for its resource that it wants kept in the network topology.
CTR ibmappnNnTopoTgLowRsns	1.3.6.1.4.1.2.6.2.13.2.1.13	Counter	read-only	Total number of topology TG updates received by this node with a RSN less than the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs, but this node will send a TDU with it's higher RSN to the sender of the low RSN.
CTR ibmappnNnTopoTgEqualRsns	1.3.6.1.4.1.2.6.2.13.2.1.14	Counter	read-only	Total number of topology TG updates received by this node with a RSN equal to the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs.
CTR ibmappnNnTopoTgGoodHighRsns	1.3.6.1.4.1.2.6.2.13.2.1.15	Counter	read-only	Total number of topology TG updates received by this node with a RSN greater than the current RSN. This results in updating this nodes topology and broadcasting the update to all adjacent network nodes.
CTR ibmappnNnTopoTgBadHighRsns	1.3.6.1.4.1.2.6.2.13.2.1.16	Counter	read-only	Total number of topology TG updates received by this node with an odd RSN greater than the current RSN. These updates represent a topology inconsistency detected by one of the APPN network nodes. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes.
CTR ibmappnNnTopoTgStateUpdates	1.3.6.1.4.1.2.6.2.13.2.1.17	Counter	read-only	Total number of topology TG records built as a result of internally detected node state changes that affect APPN topology and routing. Updates are sent via TDUs to all adjacent network nodes.
CTR ibmappnNnTopoTgErrors	1.3.6.1.4.1.2.6.2.13.2.1.18	Counter	read-only	Total number of topology TG records inconsistencies detected by this node. This occurs when this node attempts to update its topology database and detects a data inconsistency. This node will create a TDU with the current RSN incremented to the next odd number and broadcast it to all adjacent NNs.
CTR ibmappnNnTopoTgTimerUpdates	1.3.6.1.4.1.2.6.2.13.2.1.19	Counter	read-only	Total number of topology TG records built for this node's resource due to timer updates. Updates are sent via TDUs to all adjacent network nodes. These updates insure other network nodes do not delete this node's resources from their topology database.
CTR ibmappnNnTopoTgPurges	1.3.6.1.4.1.2.6.2.13.2.1.20	Counter	read-only	Total number of topology TG records purged from this node's topology database. This occurs when a TG has not been updated in a specified amount of time. The owning node is responsible for broadcasting updates for its resource that it wants to keep in the network topology.
CTR ibmappnNnTopoTotalRouteCalcs	1.3.6.1.4.1.2.6.2.13.2.1.21	Counter	read-only	Number of routes calculated for all class of services since the last initialization.
CTR ibmappnNnTopoTotalRouteRejs	1.3.6.1.4.1.2.6.2.13.2.1.22	Counter	read-only	Number of route requests for all class of services that could not be calculated since last initialization.
ibmappnNnTopoRouteTable	1.3.6.1.4.1.2.6.2.13.2.1.23		not-accessible	Table containing an entry for every Class of Service that it has calculated a route for.
ibmappnNnTopoRouteEntry	1.3.6.1.4.1.2.6.2.13.2.1.23.1		not-accessible	The Class of Service name is the index for this table.
STR ibmappnNnTopoRouteCos	1.3.6.1.4.1.2.6.2.13.2.1.23.1.1	DisplayString	read-only	The Class of Service for the route.
CTR ibmappnNnTopoRouteTrees	1.3.6.1.4.1.2.6.2.13.2.1.23.1.2	Counter	read-only	Number of routes tree caches built for this Class of Service since the last initialization.
CTR ibmappnNnTopoRouteCalcs	1.3.6.1.4.1.2.6.2.13.2.1.23.1.3	Counter	read-only	Number of routes calculated since last initialization.
CTR ibmappnNnTopoRouteRejs	1.3.6.1.4.1.2.6.2.13.2.1.23.1.4	Counter	read-only	Number of route requests that could not be calculated since last initialization.
ibmappnNnAdjNodeTable	1.3.6.1.4.1.2.6.2.13.2.2		not-accessible	Table containing an entry for every node. The information kept in this table is the last FRSN sent and received, the status of the CP-CP sessions, and a gauge that indicates the number of outstanding TDUs.
ibmappnNnAdjNodeEntry	1.3.6.1.4.1.2.6.2.13.2.2.1		not-accessible	The adjacent node name is the index for this table.
STR ibmappnNnAdjNodeAdjName	1.3.6.1.4.1.2.6.2.13.2.2.1.1	DisplayString	read-only	An administratively-assigned fully-qualified name of this node's adjacent network node.
INT ibmappnNnAdjNodeCpCpSessStatus	1.3.6.1.4.1.2.6.2.13.2.2.1.2	INTEGER	read-only	Indicates the state of CP-CP sessions between this node and adjacent network and end nodes. Incative indicates no CP-CP sessions exists between this node and the adjacent node. Active indicates CP-CP sessions are active using both the ConWinner and ConLoser sessions. The session initiated by this node is referred to as the ConWinner session and is used by this node to send to the adjacent node. The ConLoserr session is initiated by the adjacent node and is used by this node to receive from the adjacent node.
GAU ibmappnNnAdjNodeOutOfSeqTdus	1.3.6.1.4.1.2.6.2.13.2.2.1.3	Gauge	read-only	Number of out of sequence Topology Database Updates (TDUs). In a quiesced state, this value is zero. In normal operation, the value varies depending on the network environment.
INT ibmappnNnAdjNodeLastFrsnSent	1.3.6.1.4.1.2.6.2.13.2.2.1.4	INTEGER	read-only	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last TDU sent to this adjacent node.
INT ibmappnNnAdjNodeLastFrsnRcvd	1.3.6.1.4.1.2.6.2.13.2.2.1.5	INTEGER	read-only	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last TDU received from this adjacent node.
ibmappnNnTopology	1.3.6.1.4.1.2.6.2.13.2.3
ibmappnNnTopologyTable	1.3.6.1.4.1.2.6.2.13.2.3.1		not-accessible	Portion of the APPN routing table that describes all of the APPN network nodes and virtual nodes known to this node.
ibmappnNnTopologyEntry	1.3.6.1.4.1.2.6.2.13.2.3.1.1		not-accessible	The fully-qualified node name is used to index this table.
STR ibmappnNnNodeName	1.3.6.1.4.1.2.6.2.13.2.3.1.1.1	DisplayString	read-only	Administratively-assigned network name that is locally defined at each network node in the format NETID.CPNAME.
INT ibmappnNnNodeFrsn	1.3.6.1.4.1.2.6.2.13.2.3.1.1.2	INTEGER	read-only	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
INT ibmappnNnNodeEntryTimeLeft	1.3.6.1.4.1.2.6.2.13.2.3.1.1.3	INTEGER	read-only	Number of days before deletion of this network node entry. Range is 0-31.
INT ibmappnNnNodeType	1.3.6.1.4.1.2.6.2.13.2.3.1.1.4	INTEGER	read-only	Type of APPN node.
INT ibmappnNnNodeRsn	1.3.6.1.4.1.2.6.2.13.2.3.1.1.5	INTEGER	read-only	Resource sequence number that is assigned and controlled by the network node that owns this resource. This is always an even 32-bit number unless an error has occurred.
INT ibmappnNnNodeRouteAddResist	1.3.6.1.4.1.2.6.2.13.2.3.1.1.6	INTEGER	read-only	Route addition resistance indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing.
INT ibmappnNnNodeCongested	1.3.6.1.4.1.2.6.2.13.2.3.1.1.7	INTEGER	read-only	Indicates whether this node is congested. This node is not be included in route selection by other nodes when this congestion exists.
INT ibmappnNnNodeIsrDepleted	1.3.6.1.4.1.2.6.2.13.2.3.1.1.8	INTEGER	read-only	Indicates whether intermediate session routing resources are depleted. This node is not included in intermediate route selection by other nodes when resources are depleted.
INT ibmappnNnNodeEndptDepleted	1.3.6.1.4.1.2.6.2.13.2.3.1.1.9	INTEGER	read-only	Indicates whether session endpoint resources are depleted.
INT ibmappnNnNodeQuiescing	1.3.6.1.4.1.2.6.2.13.2.3.1.1.10	INTEGER	read-only	Indicates whether the node is quiescing. This node is not included in route selection by other nodes when the node is quiescing.
INT ibmappnNnNodeGateway	1.3.6.1.4.1.2.6.2.13.2.3.1.1.11	INTEGER	read-only	Indicates whether the node provide gateway functions.
INT ibmappnNnNodeCentralDirectory	1.3.6.1.4.1.2.6.2.13.2.3.1.1.12	INTEGER	read-only	Indicates whether the node is central directory.
INT ibmappnNnNodeIsr	1.3.6.1.4.1.2.6.2.13.2.3.1.1.13	INTEGER	read-only	Indicates whether the node supports intermediate session routing (ISR).
INT ibmappnNnNodeChainSupport	1.3.6.1.4.1.2.6.2.13.2.3.1.1.14	INTEGER	read-only	Indicates whether the node supports chaining.
ibmappnNnTgTopologyTable	1.3.6.1.4.1.2.6.2.13.2.3.2		not-accessible	Portion of the APPN topology database that describes all of the APPN transmissions groups used by the APPN network nodes.
ibmappnNnTgTopologyEntry	1.3.6.1.4.1.2.6.2.13.2.3.2.1		not-accessible	This table requires three indexes to provide a unique index. The indexes are the owning or originating CPname, the destination CPname, and the TG number.
STR ibmappnNnTgOwner	1.3.6.1.4.1.2.6.2.13.2.3.2.1.1	DisplayString	read-only	Administratively-assigned name for the originating node for this TG. The format is NETID.CPNAME and is the same name specified in the node table.
STR ibmappnNnTgDest	1.3.6.1.4.1.2.6.2.13.2.3.2.1.2	DisplayString	read-only	Administratively-assigned fully-qualified network name for the destination node for this TG.
INT ibmappnNnTgNum	1.3.6.1.4.1.2.6.2.13.2.3.2.1.3	INTEGER	read-only	Number associated with this transmission group. Range is 0-255.
INT ibmappnNnTgFrsn	1.3.6.1.4.1.2.6.2.13.2.3.2.1.4	INTEGER	read-only	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
INT ibmappnNnTgEntryTimeLeft	1.3.6.1.4.1.2.6.2.13.2.3.2.1.5	INTEGER	read-only	Number of days before deletion of this network node TG entry. Range is 0-31.
INT ibmappnNnTgDestVirtual	1.3.6.1.4.1.2.6.2.13.2.3.2.1.6	INTEGER	read-only	Indicates whether the destination node is a virtual node.
OCT ibmappnNnTgDlcData	1.3.6.1.4.1.2.6.2.13.2.3.2.1.7	OCTET STRING	read-only	DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits
INT ibmappnNnTgRsn	1.3.6.1.4.1.2.6.2.13.2.3.2.1.8	INTEGER	read-only	Current owning node's resource sequence number for this resource.
INT ibmappnNnTgOperational	1.3.6.1.4.1.2.6.2.13.2.3.2.1.9	INTEGER	read-only	Indicates whether the transmission group is operational.
INT ibmappnNnTgQuiescing	1.3.6.1.4.1.2.6.2.13.2.3.2.1.10	INTEGER	read-only	Indicates whether the transmission group is quiescing.
INT ibmappnNnTgCpCpSession	1.3.6.1.4.1.2.6.2.13.2.3.2.1.11	INTEGER	read-only	Indicates whether CP-CP sessions are supported on this TG.
INT ibmappnNnTgEffCap	1.3.6.1.4.1.2.6.2.13.2.3.2.1.12	INTEGER	read-only	The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgConnCost	1.3.6.1.4.1.2.6.2.13.2.3.2.1.13	INTEGER	read-only	Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgByteCost	1.3.6.1.4.1.2.6.2.13.2.3.2.1.14	INTEGER	read-only	Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgSecurity	1.3.6.1.4.1.2.6.2.13.2.3.2.1.15	INTEGER	read-only	The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgDelay	1.3.6.1.4.1.2.6.2.13.2.3.2.1.16	INTEGER	read-only	Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgModemClass	1.3.6.1.4.1.2.6.2.13.2.3.2.1.17	INTEGER	read-only	This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector; for a non-connection network it is X'00'.
INT ibmappnNnTgUsr1	1.3.6.1.4.1.2.6.2.13.2.3.2.1.18	INTEGER	read-only	First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgUsr2	1.3.6.1.4.1.2.6.2.13.2.3.2.1.19	INTEGER	read-only	Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgUsr3	1.3.6.1.4.1.2.6.2.13.2.3.2.1.20	INTEGER	read-only	Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
ibmappnNnTopologyFRTable	1.3.6.1.4.1.2.6.2.13.2.3.3		not-accessible	Portion of the APPN routing table that describes all of the APPN network nodes and virtual nodes known to this node.
ibmappnNnTopologyFREntry	1.3.6.1.4.1.2.6.2.13.2.3.3.1		not-accessible	The fully-qualified node name is used to index this table.
STR ibmappnNnNodeFRName	1.3.6.1.4.1.2.6.2.13.2.3.3.1.1	DisplayString	read-only	Administratively-assigned network name that is locally defined at each network node in the format NETID.CPNAME.
INT ibmappnNnNodeFRFrsn	1.3.6.1.4.1.2.6.2.13.2.3.3.1.2	INTEGER	read-only	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
INT ibmappnNnNodeFREntryTimeLeft	1.3.6.1.4.1.2.6.2.13.2.3.3.1.3	INTEGER	read-only	Number of days before deletion of this network node entry. Range is 0-31.
INT ibmappnNnNodeFRType	1.3.6.1.4.1.2.6.2.13.2.3.3.1.4	INTEGER	read-only	Type of APPN node.
INT ibmappnNnNodeFRRsn	1.3.6.1.4.1.2.6.2.13.2.3.3.1.5	INTEGER	read-only	Resource sequence number that is assigned and controlled by the network node that owns this resource. This is always an even 32-bit number unless an error has occurred.
INT ibmappnNnNodeFRRouteAddResist	1.3.6.1.4.1.2.6.2.13.2.3.3.1.6	INTEGER	read-only	Route addition resistance indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing.
INT ibmappnNnNodeFRCongested	1.3.6.1.4.1.2.6.2.13.2.3.3.1.7	INTEGER	read-only	Indicates whether this node is congested. This node is not be included in route selection by other nodes when this congestion exists.
INT ibmappnNnNodeFRIsrDepleted	1.3.6.1.4.1.2.6.2.13.2.3.3.1.8	INTEGER	read-only	Indicates whether intermediate session routing resources are depleted. This node is not included in intermediate route selection by other nodes when resources are depleted.
INT ibmappnNnNodeFREndptDepleted	1.3.6.1.4.1.2.6.2.13.2.3.3.1.9	INTEGER	read-only	Indicates whether session endpoint resources are depleted.
INT ibmappnNnNodeFRQuiescing	1.3.6.1.4.1.2.6.2.13.2.3.3.1.10	INTEGER	read-only	Indicates whether the node is quiescing. This node is not included in route selection by other nodes when the node is quiescing.
INT ibmappnNnNodeFRGateway	1.3.6.1.4.1.2.6.2.13.2.3.3.1.11	INTEGER	read-only	Indicates whether the node provide gateway functions.
INT ibmappnNnNodeFRCentralDirectory	1.3.6.1.4.1.2.6.2.13.2.3.3.1.12	INTEGER	read-only	Indicates whether the node is central directory.
INT ibmappnNnNodeFRIsr	1.3.6.1.4.1.2.6.2.13.2.3.3.1.13	INTEGER	read-only	Indicates whether the node supports intermediate session routing (ISR).
INT ibmappnNnNodeFRChainSupport	1.3.6.1.4.1.2.6.2.13.2.3.3.1.14	INTEGER	read-only	Indicates whether the node supports chaining.
ibmappnNnTgTopologyFRTable	1.3.6.1.4.1.2.6.2.13.2.3.4		not-accessible	Portion of the APPN topology database that describes all of the APPN transmissions groups used by the APPN network nodes.
ibmappnNnTgTopologyFREntry	1.3.6.1.4.1.2.6.2.13.2.3.4.1		not-accessible	This table is indexed by four columns: FRSN, TG owner fully-qualified node name, TG destination fully-qualified node name, TG number.
STR ibmappnNnTgFROwner	1.3.6.1.4.1.2.6.2.13.2.3.4.1.1	DisplayString	read-only	Administratively-assigned name for the originating node for this TG. The format is NETID.CPNAME and is the same name specified in the node table.
STR ibmappnNnTgFRDest	1.3.6.1.4.1.2.6.2.13.2.3.4.1.2	DisplayString	read-only	Administratively-assigned fully-qualified network name for the destination node for this TG.
INT ibmappnNnTgFRNum	1.3.6.1.4.1.2.6.2.13.2.3.4.1.3	INTEGER	read-only	Number associated with this transmission group. Range is 0-255.
INT ibmappnNnTgFRFrsn	1.3.6.1.4.1.2.6.2.13.2.3.4.1.4	INTEGER	read-only	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
INT ibmappnNnTgFREntryTimeLeft	1.3.6.1.4.1.2.6.2.13.2.3.4.1.5	INTEGER	read-only	Number of days before deletion of this network node TG entry. Range is 0-31.
INT ibmappnNnTgFRDestVirtual	1.3.6.1.4.1.2.6.2.13.2.3.4.1.6	INTEGER	read-only	Indicates whether the destination node is a virtual node.
OCT ibmappnNnTgFRDlcData	1.3.6.1.4.1.2.6.2.13.2.3.4.1.7	OCTET STRING	read-only	DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits
INT ibmappnNnTgFRRsn	1.3.6.1.4.1.2.6.2.13.2.3.4.1.8	INTEGER	read-only	Current owning node's resource sequence number for this resource.
INT ibmappnNnTgFROperational	1.3.6.1.4.1.2.6.2.13.2.3.4.1.9	INTEGER	read-only	Indicates whether the transmission group is operational.
INT ibmappnNnTgFRQuiescing	1.3.6.1.4.1.2.6.2.13.2.3.4.1.10	INTEGER	read-only	Indicates whether the transmission group is quiescing.
INT ibmappnNnTgFRCpCpSession	1.3.6.1.4.1.2.6.2.13.2.3.4.1.11	INTEGER	read-only	Indicates whether CP-CP sessions are supported on this TG.
INT ibmappnNnTgFREffCap	1.3.6.1.4.1.2.6.2.13.2.3.4.1.12	INTEGER	read-only	The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgFRConnCost	1.3.6.1.4.1.2.6.2.13.2.3.4.1.13	INTEGER	read-only	Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgFRByteCost	1.3.6.1.4.1.2.6.2.13.2.3.4.1.14	INTEGER	read-only	Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgFRSecurity	1.3.6.1.4.1.2.6.2.13.2.3.4.1.15	INTEGER	read-only	The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgFRDelay	1.3.6.1.4.1.2.6.2.13.2.3.4.1.16	INTEGER	read-only	Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgFRModemClass	1.3.6.1.4.1.2.6.2.13.2.3.4.1.17	INTEGER	read-only	This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector; for a non-connection network it is X'00'.
INT ibmappnNnTgFRUsr1	1.3.6.1.4.1.2.6.2.13.2.3.4.1.18	INTEGER	read-only	First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgFRUsr2	1.3.6.1.4.1.2.6.2.13.2.3.4.1.19	INTEGER	read-only	Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
INT ibmappnNnTgFRUsr3	1.3.6.1.4.1.2.6.2.13.2.3.4.1.20	INTEGER	read-only	Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
ibmappnLocalTopology	1.3.6.1.4.1.2.6.2.13.3
ibmappnLocalThisNode	1.3.6.1.4.1.2.6.2.13.3.1
ibmappnLocalGeneral	1.3.6.1.4.1.2.6.2.13.3.1.1
STR ibmappnLocalNodeName	1.3.6.1.4.1.2.6.2.13.3.1.1.1	DisplayString	read-only	Administratively-assigned fully-qualified name for this node. Format is NETID.CPNAME.
INT ibmappnLocalNodeType	1.3.6.1.4.1.2.6.2.13.3.1.1.2	INTEGER	read-only	Type of APPN node.
ibmappnLocalNnSpecific	1.3.6.1.4.1.2.6.2.13.3.1.2
INT ibmappnLocalNnRsn	1.3.6.1.4.1.2.6.2.13.3.1.2.1	INTEGER	read-only	Resource sequence number is assigned and controlled by the network node that owns this resource. This is always an even unsigned number unless an error has occurred.
INT ibmappnLocalNnRouteAddResist	1.3.6.1.4.1.2.6.2.13.3.1.2.2	INTEGER	read-only	Route addition resistance indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing.
INT ibmappnLocalNnCongested	1.3.6.1.4.1.2.6.2.13.3.1.2.3	INTEGER	read-only	Indicates whether this node is congested. Other network nodes stop routing traffic to this node while this flag is on.
INT ibmappnLocalNnIsrDepleted	1.3.6.1.4.1.2.6.2.13.3.1.2.4	INTEGER	read-only	Indicate whether intermediated session routing resources are depleted. Other network nodes stop routing traffic through this node while this flag is on.
INT ibmappnLocalNnEndptDepleted	1.3.6.1.4.1.2.6.2.13.3.1.2.5	INTEGER	read-only	Indicates whether session endpoint resources are depleted.
INT ibmappnLocalNnQuiescing	1.3.6.1.4.1.2.6.2.13.3.1.2.6	INTEGER	read-only	Indicates whether the node is quiescing.
INT ibmappnLocalNnGateway	1.3.6.1.4.1.2.6.2.13.3.1.2.7	INTEGER	read-only	Indicates whether the node is a gateway.
INT ibmappnLocalNnCentralDirectory	1.3.6.1.4.1.2.6.2.13.3.1.2.8	INTEGER	read-only	Indicates whether the node is a central directory.
INT ibmappnLocalNnIsr	1.3.6.1.4.1.2.6.2.13.3.1.2.9	INTEGER	read-only	Indicates whether the node supports intermediate session routing.
INT ibmappnLocalNnChainSupport	1.3.6.1.4.1.2.6.2.13.3.1.2.10	INTEGER	read-only	Indicates whether the node supports chaining.
INT ibmappnLocalNnFrsn	1.3.6.1.4.1.2.6.2.13.3.1.2.11	INTEGER	read-only	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This object is the last FRSN sent in a topology update to adjacent network nodes.
ibmappnLocalTg	1.3.6.1.4.1.2.6.2.13.3.1.3
ibmappnLocalTgTable	1.3.6.1.4.1.2.6.2.13.3.1.3.1		not-accessible	TG Table describes all of the TGs owned by this node. The TG destination can be a virtual node, network node, len, or end node.
ibmappnLocalTgEntry	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1		not-accessible	This table is indexed by the destination CPname and the TG number.
STR ibmappnLocalTgDest	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.1	DisplayString	read-only	Administratively-assigned name for the destination node for this TG. This is the fully-qualified network node name.
INT ibmappnLocalTgNum	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.2	INTEGER	read-only	Number associated with this transmission group.
INT ibmappnLocalTgDestVirtual	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.3	INTEGER	read-only	Indicates whether the destination node is a Virtual node.
OCT ibmappnLocalTgDlcData	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.4	OCTET STRING	read-only	DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits
INT ibmappnLocalTgRsn	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.5	INTEGER	read-only	The resource sequence number is assigned and controlled by the network node that owns this resource. This is always an even unsigned number unless an error has occurred.
INT ibmappnLocalTgQuiescing	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.6	INTEGER	read-only	Indicates whether the Transmission Group is quiescing.
INT ibmappnLocalTgOperational	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.7	INTEGER	read-only	Indicates whether the Transmission Group is operational.
INT ibmappnLocalTgCpCpSession	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.8	INTEGER	read-only	Indicates whether the CP-CP Sessions are supported on this TG.
INT ibmappnLocalTgEffCap	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.9	INTEGER	read-only	The effective capacity is an integer value that indicates the actual kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776.
INT ibmappnLocalTgConnCost	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.10	INTEGER	read-only	Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
INT ibmappnLocalTgByteCost	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.11	INTEGER	read-only	Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255.
INT ibmappnLocalTgSecurity	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.12	INTEGER	read-only	Security level for this TG.
INT ibmappnLocalTgDelay	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.13	INTEGER	read-only	Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated.
INT ibmappnLocalTgModemClass	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.14	INTEGER	read-only	This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector and for a non-connection network it is zero.
INT ibmappnLocalTgUsr1	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.15	INTEGER	read-only	Value of the first user-defined TG characteristic for this TG. Range is 0-255.
INT ibmappnLocalTgUsr2	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.16	INTEGER	read-only	Value of the second user-defined TG characteristic for this TG. Range is 0-255.
INT ibmappnLocalTgUsr3	1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.17	INTEGER	read-only	Value of the third user-defined TG characteristic for this TG. Range is 0-255.
ibmappnLocalEnTopology	1.3.6.1.4.1.2.6.2.13.3.2
ibmappnLocalEnTable	1.3.6.1.4.1.2.6.2.13.3.2.1		not-accessible	Portion of the APPN topology database that describes the end nodes known to this node.
ibmappnLocalEnEntry	1.3.6.1.4.1.2.6.2.13.3.2.1.1		not-accessible	This table is indexed by the end node CPname.
STR ibmappnLocalEnName	1.3.6.1.4.1.2.6.2.13.3.2.1.1.1	DisplayString	read-only	Administratively-assigned fully-qualified name of end node in the format NETID.CPNAME.
INT ibmappnLocalEnEntryTimeLeft	1.3.6.1.4.1.2.6.2.13.3.2.1.1.2	INTEGER	read-only	Number of days before deletion of this end node entry. Range is 0-31.
INT ibmappnLocalEnType	1.3.6.1.4.1.2.6.2.13.3.2.1.1.3	INTEGER	read-only	Type of APPN node (must always be a len or end node).
ibmappnLocalEnTgTable	1.3.6.1.4.1.2.6.2.13.3.2.2		not-accessible	Table describing all of the TGs owned by the end nodes known to this node. The TG destination can be a virtual node, network node, or end node.
ibmappnLocalEnTgEntry	1.3.6.1.4.1.2.6.2.13.3.2.2.1		not-accessible	This table requires multiple indexes to uniquely identify each TG. They are originating CPname, destination CPname, and the TG number.
STR ibmappnLocalEnTgOrigin	1.3.6.1.4.1.2.6.2.13.3.2.2.1.1	DisplayString	read-only	Administratively-assigned name for the origination node for this TG. This is the fully-qualified network name.
STR ibmappnLocalEnTgDest	1.3.6.1.4.1.2.6.2.13.3.2.2.1.2	DisplayString	read-only	Administratively-assigned name for the destination node for this TG. This is the fully-qualified network name.
INT ibmappnLocalEnTgNum	1.3.6.1.4.1.2.6.2.13.3.2.2.1.3	INTEGER	read-only	Number associated with this transmission group.
INT ibmappnLocalEnTgEntryTimeLeft	1.3.6.1.4.1.2.6.2.13.3.2.2.1.4	INTEGER	read-only	Number of days before deletion of this end node TG entry. Range is 0-31.
INT ibmappnLocalEnTgDestVirtual	1.3.6.1.4.1.2.6.2.13.3.2.2.1.5	INTEGER	read-only	Indicates whether the destination node is a virtual node.
OCT ibmappnLocalEnTgDlcData	1.3.6.1.4.1.2.6.2.13.3.2.2.1.6	OCTET STRING	read-only	DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits
INT ibmappnLocalEnTgOperational	1.3.6.1.4.1.2.6.2.13.3.2.2.1.7	INTEGER	read-only	Indicates whether the Transmission Group is operational.
INT ibmappnLocalEnTgCpCpSession	1.3.6.1.4.1.2.6.2.13.3.2.2.1.8	INTEGER	read-only	Indicates whether CP-CP sessions are supported on this TG.
INT ibmappnLocalEnTgEffCap	1.3.6.1.4.1.2.6.2.13.3.2.2.1.9	INTEGER	read-only	The effective capacity is an integer value that indicates the actual kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776.
INT ibmappnLocalEnTgConnCost	1.3.6.1.4.1.2.6.2.13.3.2.2.1.10	INTEGER	read-only	Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
INT ibmappnLocalEnTgByteCost	1.3.6.1.4.1.2.6.2.13.3.2.2.1.11	INTEGER	read-only	Relative cost of transmitting a byte over this link. Range is from 0, which means no cost, to 255.
INT ibmappnLocalEnTgSecurity	1.3.6.1.4.1.2.6.2.13.3.2.2.1.12	INTEGER	read-only	Security level for this TG.
INT ibmappnLocalEnTgDelay	1.3.6.1.4.1.2.6.2.13.3.2.2.1.13	INTEGER	read-only	Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated.
INT ibmappnLocalEnTgModemClass	1.3.6.1.4.1.2.6.2.13.3.2.2.1.14	INTEGER	read-only	This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector and for a non connection network it is zero.
INT ibmappnLocalEnTgUsr1	1.3.6.1.4.1.2.6.2.13.3.2.2.1.15	INTEGER	read-only	First user-defined TG characteristic for this TG. Range of values is 0-255.
INT ibmappnLocalEnTgUsr2	1.3.6.1.4.1.2.6.2.13.3.2.2.1.16	INTEGER	read-only	Second user-defined TG characteristic for this TG. Range of values is 0-255.
INT ibmappnLocalEnTgUsr3	1.3.6.1.4.1.2.6.2.13.3.2.2.1.17	INTEGER	read-only	Third user-defined TG characteristic for this TG. Range of values is 0-255.
ibmappnDir	1.3.6.1.4.1.2.6.2.13.5
ibmappnDirPerf	1.3.6.1.4.1.2.6.2.13.5.1
INT ibmappnDirMaxCaches	1.3.6.1.4.1.2.6.2.13.5.1.1	INTEGER	read-only	Maximum number of cache entries allowed. This is an administratively assigned value.
GAU ibmappnDirCurCaches	1.3.6.1.4.1.2.6.2.13.5.1.2	Gauge	read-only	Current number of cache entries.
GAU ibmappnDirCurHomeEntries	1.3.6.1.4.1.2.6.2.13.5.1.3	Gauge	read-only	Current number of home entries.
GAU ibmappnDirRegEntries	1.3.6.1.4.1.2.6.2.13.5.1.4	Gauge	read-only	Current number of registered entries.
CTR ibmappnDirInLocates	1.3.6.1.4.1.2.6.2.13.5.1.5	Counter	read-only	Number of directed locates received.
CTR ibmappnDirInBcastLocates	1.3.6.1.4.1.2.6.2.13.5.1.6	Counter	read-only	Number of broadcast locates received.
CTR ibmappnDirOutLocates	1.3.6.1.4.1.2.6.2.13.5.1.7	Counter	read-only	Number of directed locates sent.
CTR ibmappnDirOutBcastLocates	1.3.6.1.4.1.2.6.2.13.5.1.8	Counter	read-only	Number of broadcast locates sent.
CTR ibmappnDirNotFoundLocates	1.3.6.1.4.1.2.6.2.13.5.1.9	Counter	read-only	Number of directed locates returned with a 'not found'.
CTR ibmappnDirNotFoundBcastLocates	1.3.6.1.4.1.2.6.2.13.5.1.10	Counter	read-only	Number of broadcast locates returned with a not found.
GAU ibmappnDirLocateOutstands	1.3.6.1.4.1.2.6.2.13.5.1.11	Gauge	read-only	Current number of outstanding locates, both directed and broadcast. This value varies. A value of zero indicates that no locates are unanswered.
ibmappnDirTable	1.3.6.1.4.1.2.6.2.13.5.2		not-accessible	Table containing information about all known LUs and TPs.
ibmappnDirEntry	1.3.6.1.4.1.2.6.2.13.5.2.1		not-accessible	This table is indexed by the LU name.
STR ibmappnDirLuName	1.3.6.1.4.1.2.6.2.13.5.2.1.1	DisplayString	read-only	Fully-qualified network LU name in the domain of the serving network node.
STR ibmappnDirServerName	1.3.6.1.4.1.2.6.2.13.5.2.1.2	DisplayString	read-only	Fully-qualified control point (CP) name of the network node server. For unassociated end node entries, the end node fully-qualified name is returned.
STR ibmappnDirLuOwnerName	1.3.6.1.4.1.2.6.2.13.5.2.1.3	DisplayString	read-only	Fully-qualified CP name of the node at which the LU is located. This name is the same as the serving NN name when the LU is located at a network node or an unassociated end node. It is also the same as the fully-qualified LU name when this is the control point LU for this node.
INT ibmappnDirLuLocation	1.3.6.1.4.1.2.6.2.13.5.2.1.4	INTEGER	read-only	Specifies the location of the LU.
INT ibmappnDirType	1.3.6.1.4.1.2.6.2.13.5.2.1.5	INTEGER	read-only	Directory types are: 1 - Home The LU is in the domain of the local network node and the LU information has been configured at the local node. 2 - Cache The LU has previously been located by a broadcast search and the location information has been saved. 3 - Register The LU is at an end node that is in the domain of the local network node. Registered entries are registered by the served end node.
INT ibmappnDirWildCard	1.3.6.1.4.1.2.6.2.13.5.2.1.6	INTEGER	read-only	1 - Other means unknown type of LU entry. 2 - Expliced-entry means the full LUNAME will be used for locating this LU. 3 - Partial-wildcard means only the non-blank portions of the LUNAME will be used for locating this LU. 4 - Full-wildcard means all LUNAMES will be directed to this LU.
ibmappnCos	1.3.6.1.4.1.2.6.2.13.6
ibmappnCosModeTable	1.3.6.1.4.1.2.6.2.13.6.1		not-accessible	Table representing all of the defined mode names for this node. The table contains the matching COS name.
ibmappnCosModeEntry	1.3.6.1.4.1.2.6.2.13.6.1.1		not-accessible	This table is indexed by the Mode Name.
STR ibmappnCosModeName	1.3.6.1.4.1.2.6.2.13.6.1.1.1	DisplayString	read-only	Administratively-assigned name for this mode entry.
STR ibmappnCosModeCosName	1.3.6.1.4.1.2.6.2.13.6.1.1.2	DisplayString	read-only	An administratively assigned name for this Class of Service.
ibmappnCosNameTable	1.3.6.1.4.1.2.6.2.13.6.2		not-accessible	Table representing all of the defined class-of-service names for this node. The COS node and TG tables are accessed using the same index, which is the COS name.
ibmappnCosNameEntry	1.3.6.1.4.1.2.6.2.13.6.2.1		not-accessible	The COS name is the index to this table.
STR ibmappnCosName	1.3.6.1.4.1.2.6.2.13.6.2.1.1	DisplayString	read-only	Administratively-assigned name for this class of service.
INT ibmappnCosTransPriority	1.3.6.1.4.1.2.6.2.13.6.2.1.2	INTEGER	read-only	Transmission priority for this class of service. Values are: Low Medium High Network
ibmappnCosNodeRowTable	1.3.6.1.4.1.2.6.2.13.6.3		not-accessible	This table contains all node-row information for all class of service in this node.
ibmappnCosNodeRowEntry	1.3.6.1.4.1.2.6.2.13.6.3.1		not-accessible	The COS name is the first index and a integer is the second index to insure a unique index.
STR ibmappnCosNodeRowName	1.3.6.1.4.1.2.6.2.13.6.3.1.1	DisplayString	read-only	Administratively-assigned name for this class of service.
INT ibmappnCosNodeRowIndex	1.3.6.1.4.1.2.6.2.13.6.3.1.2	INTEGER	read-only	Index of COS name. This same value is used to access the node and TG COS tables. Range of values is 0-255.
STR ibmappnCosNodeRowWgt	1.3.6.1.4.1.2.6.2.13.6.3.1.3	DisplayString	read-only	Weight to be associated with the nodes that fit the criteria specified by this node row.
INT ibmappnCosNodeRowResistMin	1.3.6.1.4.1.2.6.2.13.6.3.1.4	INTEGER	read-only	Minimum route addition resistance value for this node. Range of values is 0-255. The lower the value, the more desirable the node is for intermediate routing.
INT ibmappnCosNodeRowResistMax	1.3.6.1.4.1.2.6.2.13.6.3.1.5	INTEGER	read-only	Maximum route addition resistance value for this node. Range of values is 0-255. The lower the value, the more desirable the node is for intermediate routing.
INT ibmappnCosNodeRowMinCongestAllow	1.3.6.1.4.1.2.6.2.13.6.3.1.6	INTEGER	read-only	Indicates whether low congestion will be tolerated. The minimum and maximum parameters will allow specifying either low-congested, high-congested, or either to be used.
INT ibmappnCosNodeRowMaxCongestAllow	1.3.6.1.4.1.2.6.2.13.6.3.1.7	INTEGER	read-only	Indicates whether high congestion will be tolerated. The minimum and maximum parameters will allow specifying either low-congested, high-congested, or either to be used.
ibmappnCosTgRowTable	1.3.6.1.4.1.2.6.2.13.6.4		not-accessible	Table containing all the Tg-row information for all class of service defined in this node.
ibmappnCosTgRowEntry	1.3.6.1.4.1.2.6.2.13.6.4.1		not-accessible	The TgRowName and the TgRowIndex are the index for this table.
STR ibmappnCosTgRowName	1.3.6.1.4.1.2.6.2.13.6.4.1.1	DisplayString	read-only	Administratively-assigned name for this class of service.
INT ibmappnCosTgRowIndex	1.3.6.1.4.1.2.6.2.13.6.4.1.2	INTEGER	read-only	Index of COS name. This same value is used to access the node and TG COS tables.
STR ibmappnCosTgRowWgt	1.3.6.1.4.1.2.6.2.13.6.4.1.3	DisplayString	read-only	Weight to be associated with the nodes that fit the criteria specified by this tg-row.
INT ibmappnCosTgRowEffCapMin	1.3.6.1.4.1.2.6.2.13.6.4.1.4	INTEGER	read-only	Minimum acceptable speed for this Class of Service. The effective capacity is an integer value that indicates the actual kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776.
INT ibmappnCosTgRowEffCapMax	1.3.6.1.4.1.2.6.2.13.6.4.1.5	INTEGER	read-only	Maximum acceptable speed for this Class of Service. The effective capacity is an integer value that indicates the actual kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776.
INT ibmappnCosTgRowConnCostMin	1.3.6.1.4.1.2.6.2.13.6.4.1.6	INTEGER	read-only	Minimum acceptable cost per connect time for this Class of Service. Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
INT ibmappnCosTgRowConnCostMax	1.3.6.1.4.1.2.6.2.13.6.4.1.7	INTEGER	read-only	Maximum acceptable cost per connect time for this Class of Service. Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
INT ibmappnCosTgRowByteCostMin	1.3.6.1.4.1.2.6.2.13.6.4.1.8	INTEGER	read-only	Minimum acceptable cost per byte for this Class of Service.
INT ibmappnCosTgRowByteCostMax	1.3.6.1.4.1.2.6.2.13.6.4.1.9	INTEGER	read-only	Maximum acceptable cost per byte for this Class of Service.
INT ibmappnCosTgRowSecurityMin	1.3.6.1.4.1.2.6.2.13.6.4.1.10	INTEGER	read-only	Minimum acceptable security for this Class of Service.
INT ibmappnCosTgRowSecurityMax	1.3.6.1.4.1.2.6.2.13.6.4.1.11	INTEGER	read-only	Maximum acceptable security for this Class of Service.
INT ibmappnCosTgRowDelayMin	1.3.6.1.4.1.2.6.2.13.6.4.1.12	INTEGER	read-only	Minimum acceptable propagation delay for this class of service. Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with the more values enumerated.
INT ibmappnCosTgRowDelayMax	1.3.6.1.4.1.2.6.2.13.6.4.1.13	INTEGER	read-only	Maximum acceptable propagation delay for this class of service. Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with the more values enumerated.
INT ibmappnCosTgRowUsr1Min	1.3.6.1.4.1.2.6.2.13.6.4.1.14	INTEGER	read-only	Minimum acceptable value for this user defined characteristic. Range of values is 0-255.
INT ibmappnCosTgRowUsr1Max	1.3.6.1.4.1.2.6.2.13.6.4.1.15	INTEGER	read-only	Maximum acceptable value for this user defined characteristic. Range of values is 0-255.
INT ibmappnCosTgRowUsr2Min	1.3.6.1.4.1.2.6.2.13.6.4.1.16	INTEGER	read-only	Minimum acceptable value for this user defined characteristic. Range of values is 0-255.
INT ibmappnCosTgRowUsr2Max	1.3.6.1.4.1.2.6.2.13.6.4.1.17	INTEGER	read-only	A Maximum acceptable value for this user defined characteristic.
INT ibmappnCosTgRowUsr3Min	1.3.6.1.4.1.2.6.2.13.6.4.1.18	INTEGER	read-only	Minimum acceptable value for this user defined characteristic. Range of values is 0-255.
INT ibmappnCosTgRowUsr3Max	1.3.6.1.4.1.2.6.2.13.6.4.1.19	INTEGER	read-only	Maximum acceptable value for this user defined characteristic. Range of values is 0-255.
ibmappnSession	1.3.6.1.4.1.2.6.2.13.7
ibmappnSessIntermediate	1.3.6.1.4.1.2.6.2.13.7.3
ibmappnIsInformation	1.3.6.1.4.1.2.6.2.13.7.3.1
ibmappnIsInGlobal	1.3.6.1.4.1.2.6.2.13.7.3.1.1
INT ibmappnIsInGlobeStatus	1.3.6.1.4.1.2.6.2.13.7.3.1.1.1	INTEGER	read-only	Indicates the current collection options in effect: 1. notActive: collection of counters and some names is not active. 2. active: collection of counters and some names is active.
INT ibmappnIsInGlobeRscv	1.3.6.1.4.1.2.6.2.13.7.3.1.1.2	INTEGER	read-only	Indicates the current collection options in effect: 1. notActive: collection of route selection control vectors is not active. 2. active: collection of route selection control vectors is active.
TIK ibmappnIsInGlobeRscvTime	1.3.6.1.4.1.2.6.2.13.7.3.1.1.3	TimeTicks	read-only	Time when the ibmappnIsInGlobeRscv object last changed. This time is in hundreds of a second.
INT ibmappnIsInGlobeCtrStatus	1.3.6.1.4.1.2.6.2.13.7.3.1.1.4	INTEGER	read-only	Indicates whether or not the intermediate session counters are active. This object reflects the combination of the ibmappnIsInGlobeStatus object and the ibmappnIsAcBtypeActive object. The values are: 1. notActive: collection of counters and some names is not active. 2. active: collection of counters and some names is active.
TIK ibmappnIsInGlobeCtrStatusTime	1.3.6.1.4.1.2.6.2.13.7.3.1.1.5	TimeTicks	read-only	Time when the ibmappnIsInGlobeCtrStatus object last changed. This time is in hundreds of a second.
ibmappnIsInTable	1.3.6.1.4.1.2.6.2.13.7.3.1.2		not-accessible	Intermediate Session Information Table
ibmappnIsInEntry	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1		not-accessible	Entry of Intermediate Session Information Table.
STR ibmappnIsInFqLuName	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.1	DisplayString	read-only	The network-qualified CP name or PU name of the node at which the session and cid originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OCT ibmappnIsInPcid	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.2	OCTET STRING	read-only	The procedure correlation identifier (pcid) of a session. It is an 8-octet value assigned by the primary LU.
STR ibmappnIsInPriLuName	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.3	DisplayString	read-only	The primary LU name of the session.
STR ibmappnIsInSecLuName	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.4	DisplayString	read-only	The secondary LU name of the session.
STR ibmappnIsInModeName	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.5	DisplayString	read-only	The Mode Name name used for this session. This is a 1-8 character name.
STR ibmappnIsInCosName	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.6	DisplayString	read-only	The Class of Service (COS) name used for this session. This is a 1-8 character name.
INT ibmappnIsInTransPriority	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.7	INTEGER	read-only	The transmission priority of this session.
INT ibmappnIsInSessType	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.8	INTEGER	read-only	The type of intermediate session.
INT ibmappnIsInSessState	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.9	INTEGER	read-only	Indicates the state of the session. 1. session is pending inactive or, 2. session is pending active or, 3. session is active or, 4. session is inactive Existing sessions can be deactivated by setting this object to inactive.
TIK ibmappnIsInSessStartTime	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.10	TimeTicks	read-only	Time when the session started in hundreds of a second.
TIK ibmappnIsInSessUpTime	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.11	TimeTicks	read-only	Length of time the session has been active in hundreds of a second.
TIK ibmappnIsInCtrUpTime	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.12	TimeTicks	read-only	Length of time the session counters have been active in hundreds of a second.
CTR ibmappnIsInP2SFmdPius	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.13	Counter	read-only	Number of FMD PIUs sent from the Primary LU to the Secondary LU
CTR ibmappnIsInS2PFmdPius	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.14	Counter	read-only	Number of FMD PIUs sent from the Secondary LU to the Primary LU
CTR ibmappnIsInP2SNonFmdPius	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.15	Counter	read-only	Number of non-FMD PIUs sent from the Primary LU to the Secondary LU
CTR ibmappnIsInS2PNonFmdPius	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.16	Counter	read-only	Number of non-FMD PIUs sent from the Secondary LU to the Primary LU
CTR ibmappnIsInP2SFmdBytes	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.17	Counter	read-only	Number of FMD Bytes sent from the Primary LU to the Secondary LU
CTR ibmappnIsInS2PFmdBytes	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.18	Counter	read-only	Number of FMD Bytes sent from the Secondary LU to the Primary LU
CTR ibmappnIsInP2SNonFmdBytes	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.19	Counter	read-only	Number of non-FMD Bytes sent from the Primary LU to the Secondary LU
CTR ibmappnIsInS2PNonFmdBytes	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.20	Counter	read-only	Number of non-FMD Bytes sent from the Secondary LU to the Primary LU
STR ibmappnIsInPsAdjCpName	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.21	DisplayString	read-only	The primary stage adjacent CP name of this session.
INT ibmappnIsInPsAdjTgNum	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.22	INTEGER	read-only	The primary stage adjacent transmission group (TG) number associated with this session.
INT ibmappnIsInPsSendMaxBtuSize	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.23	INTEGER	read-only	The primary stage maximum basic transmission size (BTU) for sending data.
INT ibmappnIsInPsSendPacingType	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.24	INTEGER	read-only	The primary stage type of pacing being used for sending data.
GAU ibmappnIsInPsSendRpc	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.25	Gauge	read-only	The primary stage send residual pace count. This represents the primary stage number of MU's that can still be sent in the current session window.
GAU ibmappnIsInPsSendNxWndwSize	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.26	Gauge	read-only	The primary stage size of the next window which will be used to send data.
INT ibmappnIsInPsRecvPacingType	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.27	INTEGER	read-only	The primary stage type of pacing being used for receiving data.
GAU ibmappnIsInPsRecvRpc	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.28	Gauge	read-only	The primary stage receive residual pace count. This represents the primary stage number of MU's that can still be received in the current session window.
GAU ibmappnIsInPsRecvNxWndwSize	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.29	Gauge	read-only	The primary stage size of the next window which will be used to receive data.
STR ibmappnIsInSsAdjCpName	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.30	DisplayString	read-only	The secondary stage adjacent CP name of this session.
INT ibmappnIsInSsAdjTgNum	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.31	INTEGER	read-only	The secondary stage adjacent transmission group (TG) number associated with this session.
INT ibmappnIsInSsSendMaxBtuSize	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.32	INTEGER	read-only	The secondary stage maximum basic transmission size (BTU) for sending data.
INT ibmappnIsInSsSendPacingType	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.33	INTEGER	read-only	The secondary stage type of pacing being used for sending data.
GAU ibmappnIsInSsSendRpc	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.34	Gauge	read-only	The secondary stage send residual pace count. This represents the secondary stage number of MU's that can still be sent in the current session window.
GAU ibmappnIsInSsSendNxWndwSize	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.35	Gauge	read-only	The secondary stage size of the next window which will be used to send data.
INT ibmappnIsInSsRecvPacingType	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.36	INTEGER	read-only	The secondary stage type of pacing being used for receiving data.
GAU ibmappnIsInSsRecvRpc	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.37	Gauge	read-only	The secondary stage send residual pace count. This represents the secondary stage number of MU's that can still be received in the current session window.
GAU ibmappnIsInSsRecvNxWndwSize	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.38	Gauge	read-only	The secondary stage size of the next window which will be used to receive data.
OCT ibmappnIsInRouteInfo	1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.39	OCTET STRING	read-only	The route selection control vector (RSCV x'2B') used for this session. It is present for APPN nodes; but is not present for LEN nodes. The format of this vector is described in SNA Formats.
ibmappnIsAccounting	1.3.6.1.4.1.2.6.2.13.7.3.2

RFC description

Defined in RFC 1593, this MIB provides management objects for SNA APPN Node management on IBM 6611 devices, including performance metrics for APPN subagents and SNMP operations.

Start monitoring IBM 6611 Network Processor / APPN-capable router with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download IBM-6611-APPN-MIB

What Is IBM-6611-APPN-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description