All MIBs › HUAWEI-MPLSLDP-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2014-11-06
Category: MPLS and Traffic Engineering, Routing Protocols, Vendor: Huawei
Description: Huawei MPLS LDP MIB (alternate module) providing LDP peer, session, and hello adjacency management objects.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-MPLSLDP-MIB?
HUAWEI-MPLSLDP-MIB is a Huawei private MIB for the Label Distribution Protocol (LDP), the control-plane protocol MPLS routers use to exchange label bindings and form label-switched paths. It exposes LDP peer discovery, session establishment, and hello-adjacency state, together with notifications/traps for LDP events. Its main monitoring value is software/control-plane health: confirming that LDP sessions to configured peers remain established and that hello adjacencies are not timing out is essential to detecting an MPLS label-distribution failure that could silently black-hole traffic across label-switched paths. It complements the standards-based MPLS-LDP-STD-MIB (RFC 3815) and is typically used alongside HUAWEI-MPLS-LSR-MIB, which covers the label-forwarding side of the same MPLS domain. It is deployed on Huawei MPLS routers running LDP within service-provider and large enterprise backbone networks. Engineers can download the HUAWEI-MPLSLDP-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-MPLSLDP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei MPLS routers
Monitoring Examples
No sample object names were supplied for this module, so specific leaf names cannot be cited. In general, an operator would poll the LDP peer and session tables to confirm each expected peer's session state remains operational rather than idle or non-existent. A peer whose session has dropped out of the established state, or whose hello-adjacency timer has expired, indicates an LDP control-plane failure that can silently break label-switched paths through that peer before any data-plane symptom appears.
What Can Be Monitored
- LDP peer discovery status
- LDP session establishment state
- hello adjacency timers
- LDP session failure/notification events
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-MIB
| hwDatacomm | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero |
From INET-ADDRESS-MIB
| InetAddress |
From MPLS-TC-STD-MIB
| MplsLdpIdentifier | |
| MplsLsrIdentifier |
From P-BRIDGE-MIB
| EnabledStatus |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwMplsLdp | 1.3.6.1.4.1.2011.5.25.143 | This MIB contains private managed object and notification trap definitions for MPLS LDP. | ||
| hwMplsLdpInfo | 1.3.6.1.4.1.2011.5.25.143.1 | |||
| OCT hwMplsLdpProcessName | 1.3.6.1.4.1.2011.5.25.143.1.1 | OCTET STRING | read-only | This object indicates the process name of LDP running on the router. By default, the value is LDP. |
| IP hwMplsLdpLspFec | 1.3.6.1.4.1.2011.5.25.143.1.2 | InetAddress | accessible-for-notify | This object indicates the destination address of an LSP. The value is either a destination IP address or a prefix of an IP address. |
| C32 hwMplsLdpLspInLabel | 1.3.6.1.4.1.2011.5.25.143.1.3 | Counter32 | accessible-for-notify | This object indicates that labels are pushed into all the packets for direct MPLS forwarding. |
| C32 hwMplsLdpLspOutLabel | 1.3.6.1.4.1.2011.5.25.143.1.4 | Counter32 | accessible-for-notify | This object indicates that all the packets swap labels for MPLS forwarding. |
| NUM hwMplsLdpLspOutIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.5 | InterfaceIndex | accessible-for-notify | The value of this object identifies the index of the outgoing interface of the LSP. |
| INT hwMplsLdpLspDownReason | 1.3.6.1.4.1.2011.5.25.143.1.6 | INTEGER | accessible-for-notify | This object indicates the cause that the LSP becomes Down. Options: 1. routeDelete(1) -indicates that a route has been deleted. 2. lspmNotify(2) -indicates that LSPM notify. 3. canNotRecoveryFromGr(3) -indicates that the recovery from GR was failed. 4. recvReleaseMsg(4) -indicates that the release message was received. 5. recvWithdrawMsg(5) -indicates that the withdraw message was received. 6. upStreamLost(6) -indicates that the upstream route was lost. 7. downStreamLost(7) -indicates that the downstream route was lost. 8. otherReason(8) -indicates that another cause was involved. |
| hwMplsLdpSessionTable | 1.3.6.1.4.1.2011.5.25.143.1.7 | not-accessible | This object is used to display the session parameters and session age. The index of this table is hwMplsLdpSessionPeerLsrId. | |
| hwMplsLdpSessionEntry | 1.3.6.1.4.1.2011.5.25.143.1.7.1 | not-accessible | This object is used to display the session parameters and session age. The index of this entry is hwMplsLdpSessionPeerLsrId. | |
| OID hwMplsLdpSessionPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.7.1.1 | MplsLdpIdentifier | not-accessible | This object indicates the LSR ID of the peer in a session. |
| I32 hwMplsLdpSessionIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.7.1.2 | Integer32 | accessible-for-notify | This object indicates the index of the interface on which the session is established. |
| INT hwMplsLdpSessionDownReason | 1.3.6.1.4.1.2011.5.25.143.1.7.1.3 | INTEGER | accessible-for-notify | This object indicates the cause that the session becomes Down. Options: 1. sessionUp(0) -indicates that the session was Up. 2. helloHoldTimerExp(1) -indicates that the Hello hold timer expired. 3. ssnHoldTimerExp(2) -indicates that the session hold timer expired. 4. resetMplsLdp(3) -indicates MPLS LDP was reset. 5. undoMplsLdp(4) -indicates that MPLS LDP was disabled. 6. undoMpls(5) -indicates that MPLS was disabled. 7. undoMplsLdpRemotePeer(6) -indicates that the remote peer was deleted. 8. modifyGRConfig(7) -indicates that GR capability was modified. 9. modifyGRTimer(8) -indicates that the GR timer was modified. 10. modifyKeepaliveTimer(9) -indicates that the keepalive timer was modified. 11. modifyMD5Config(10) -indicates that MD5 was configured. 12. ssnRoleSwitch(11) -indicates that the session role was switched. 13. modifyMTUConfig(12) -indicates that the MTU was modified. 14. modifyTransportAddress(13) -indicates that the transport address was modified. 15. modifyLDPLsrID(14) -indicates that the LDP LSR ID was modified. 16. recvNotification(15) -indicates that the notification message was received. 17. transportAddressNotMatch(16) -indicates that the transport address was not matched. 18. protocolGR(17) -indicates that the protocol GR was in processing. 19. ifStatusChanged(18) -indicates that the interface status was changed. 20. tcpDown(19) -indicates that TCP was Down. 21. otherReason(20) -indicates that another cause was involved. 22. sentNotification(21) -indicates that the notification was sent. 23. canntBuildSessionRelation(22) -indicates that the session relation cannot be built. 24. receiveErrorMessageFromPeer(23) -indicates that error message from peer was received. 25. receiveSocketError(24) -indicates that error pakcet from socket was received. 26. sessionDelete(25) -indicates that the session was deleted. 27. modifyCapabilityAnnouncementConfig(26) -indicates that the capability-announcement was modified. 28. modifyLocalLsrID(27) -indicates that the Local LSR ID was modified. 29. modifyP2MP(28) -indicates that the mLDP P2MP was modified. 30. modifyMP2MP(29) -indicates that the mLDP MP2MP was modified. 31. sessionProtectTimerExp(30) -indicates that the session protection timer expired. |
| TIK hwMplsLdpSessionAge | 1.3.6.1.4.1.2011.5.25.143.1.7.1.4 | TimeTicks | read-only | This object indicates the duration since the session is set up. |
| hwMplsLdpSessionStateTable | 1.3.6.1.4.1.2011.5.25.143.1.8 | not-accessible | This object is used to display the detailed state parameters of the session. The index of this table is hwMplsLdpSessionPeerId. | |
| hwMplsLdpSessionStateEntry | 1.3.6.1.4.1.2011.5.25.143.1.8.1 | not-accessible | This object is used to display the detailed state parameters of the session. The index of this entry is hwMplsLdpSessionPeerId. | |
| OID hwMplsLdpSessionPeerId | 1.3.6.1.4.1.2011.5.25.143.1.8.1.1 | MplsLdpIdentifier | not-accessible | This object indicates the LSR ID of the LDP peer to which the session is connected. |
| OID hwMplsLdpSessionLsrId | 1.3.6.1.4.1.2011.5.25.143.1.8.1.2 | MplsLdpIdentifier | read-only | This object indicates the ID of the local LSR. |
| OCT hwMplsLdpSessionTcpConnectionState | 1.3.6.1.4.1.2011.5.25.143.1.8.1.3 | OCTET STRING | read-only | This object indicates the TCP link status of the session. |
| OCT hwMplsLdpSessionState | 1.3.6.1.4.1.2011.5.25.143.1.8.1.4 | OCTET STRING | read-only | This object indicates the current status of the session. |
| OCT hwMplsLdpSessionRole | 1.3.6.1.4.1.2011.5.25.143.1.8.1.5 | OCTET STRING | read-only | This object indicates the session roles. |
| OCT hwMplsLdpSessionFtFlag | 1.3.6.1.4.1.2011.5.25.143.1.8.1.6 | OCTET STRING | read-only | This object indicates whether the FT of the session is enabled. |
| OCT hwMplsLdpSessionMd5Flag | 1.3.6.1.4.1.2011.5.25.143.1.8.1.7 | OCTET STRING | read-only | This object indicates whether the MD5 is enabled for the peer. |
| U32 hwMplsLdpSessionReconnectTimer | 1.3.6.1.4.1.2011.5.25.143.1.8.1.8 | Unsigned32 | read-only | This object indicates the value of the GR reconnection timer after the negotiation. Unit: seconds |
| U32 hwMplsLdpSessionRecoveryTimer | 1.3.6.1.4.1.2011.5.25.143.1.8.1.9 | Unsigned32 | read-only | This object indicates the value of the GR recovery timer after the negotiation. Unit: seconds |
| U32 hwMplsLdpSessionKeepAliveTimer | 1.3.6.1.4.1.2011.5.25.143.1.8.1.10 | Unsigned32 | read-only | This object indicates the value of the KeepAlive timer after the negotiation. Unit: seconds |
| U32 hwMplsLdpSessionKeepAliveMsgReceived | 1.3.6.1.4.1.2011.5.25.143.1.8.1.11 | Unsigned32 | read-only | This object indicates the number of the KeepAlive messages that the session obtains. |
| U32 hwMplsLdpSessionKeepAliveMsgSent | 1.3.6.1.4.1.2011.5.25.143.1.8.1.12 | Unsigned32 | read-only | This object indicates the number of the KeepAlive messages that the session sends. |
| OCT hwMplsLdpSessionLabelAdvMode | 1.3.6.1.4.1.2011.5.25.143.1.8.1.13 | OCTET STRING | read-only | This object indicates the label distribution mode of the session. |
| OCT hwMplsLdpSessionLocalLabelResourceStatus | 1.3.6.1.4.1.2011.5.25.143.1.8.1.14 | OCTET STRING | read-only | This object indicates the status of the local label resources of the session. |
| OCT hwMplsLdpSessionPeerLabelResourceStatus | 1.3.6.1.4.1.2011.5.25.143.1.8.1.15 | OCTET STRING | read-only | This object indicates the status of the label resources of the LDP peer. |
| TIK hwMplsLdpSessionAgeStatus | 1.3.6.1.4.1.2011.5.25.143.1.8.1.16 | TimeTicks | read-only | This object indicates the existence time of the session. |
| ENA hwLdpCapabilityConfig | 1.3.6.1.4.1.2011.5.25.143.1.9 | EnabledStatus | read-write | This object indicates the global configuration or deletion of the LDP capability. Before enabling LDP capability, ensure that the MPLS capability is enabled globally. |
| IP hwLdpLsrId | 1.3.6.1.4.1.2011.5.25.143.1.10 | IpAddress | read-write | This object indicates the way to change the LDP LSR ID. The default LDP LSR ID has the same value as the MPLS LSR ID. It is recommended not to change the LDP LSR ID unless necessary. |
| OCT hwLdpPropagateIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.11 | OCTET STRING | read-write | This object indicates the configuration or deletion of the transit policy for the LDP. The object has a valid length ranging from 1 to 169 characters. The length 0 characters shows that the transit policy is deleted. |
| ENA hwLdpGlobalRemotePwe3 | 1.3.6.1.4.1.2011.5.25.143.1.12 | EnabledStatus | read-write | This object indicates the configuration or deletion of the policy for the LDP remote session. When the object is enabled, it is forbidden to send mapping message to the remote peer. By default, the policy is disabled, which means that there is no limitation to send mapping message to the remote peer. |
| ENA hwLdpMtuSignaling | 1.3.6.1.4.1.2011.5.25.143.1.13 | EnabledStatus | read-write | This object indicates the configuration or deletion of the MTU signaling function. By default, the MTU signaling function is enabled, and the MTU TLV type in the LDP message is 0x900. |
| ENA hwLdpMtuApplyTlv | 1.3.6.1.4.1.2011.5.25.143.1.14 | EnabledStatus | read-write | This object conflicts with the object hwLdpMtuSignaling. If the object is enabled, it indicates that the MTU TLV type in the LDP message is 0x601 according to the RFC 3988. |
| ENA hwLdpGrCapabilityConfig | 1.3.6.1.4.1.2011.5.25.143.1.15 | EnabledStatus | read-write | This object indicates the configuration or deletion of the LDP GR capability. |
| I32 hwLdpGrNeighborLivenessTimer | 1.3.6.1.4.1.2011.5.25.143.1.16 | Integer32 | read-write | This object indicates the way to configure the value of GR neighbor life timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds |
| I32 hwLdpGrReconnectTimer | 1.3.6.1.4.1.2011.5.25.143.1.17 | Integer32 | read-write | This object indicates the way to configure the value of GR reconnect timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds |
| I32 hwLdpGrRecoveryTimer | 1.3.6.1.4.1.2011.5.25.143.1.18 | Integer32 | read-write | This object indicates the way to configure the value of GR recovery timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds |
| INT hwMplsLspTrigger | 1.3.6.1.4.1.2011.5.25.143.1.19 | INTEGER | read-write | This object indicates the way to configure the LDP policy for the ingress LSP and egress LSP. Options: 1. all(1) -indicates that all FECs are triggered for the IGP. 2. none(2) -indicates that no FEC is triggered for the IGP. 3. host(3) -indicates that the host FEC is triggered for the IGP. 4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP. If the object is set as ipprefix, the value of hwMplsLspTriggerIpPrefix must be set together. Default: host |
| OCT hwMplsLspTriggerIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.20 | OCTET STRING | read-write | This object indicates the IP prefix when configuring the LDP policy for the ingress LSP and egress LSP. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsLspTrigger must be set as ipprefix. |
| ENA hwMplsLspTriggerBgpRoute | 1.3.6.1.4.1.2011.5.25.143.1.21 | EnabledStatus | read-write | This object indicates the policy of triggering the BGP route to create the LDP LSP. Default: disabled |
| OCT hwMplsLspTriggerBgpRouteIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.22 | OCTET STRING | read-write | This object indicates the IP prefix when triggering the BGP route to create the LDP LSP. The object has a valid length ranging from 1 to 169 characters. |
| INT hwLdpReset | 1.3.6.1.4.1.2011.5.25.143.1.23 | INTEGER | read-write | This object indicates the reset of the LDP protocol. Options: 1. reset(1) -indicates the reset of the LDP protocol. 2. resetall(2) -indicates the reset of all LDP instances. 3. ready(3) -indicates that it is ready to reset LDP. This value cannot be set. |
| ENA hwLdpOutBoundSplitHorizonAll | 1.3.6.1.4.1.2011.5.25.143.1.24 | EnabledStatus | read-write | This object indicates the way to set the flag of global split horizon. Default: disabled |
| INT hwLdpDeleteGtsmAll | 1.3.6.1.4.1.2011.5.25.143.1.25 | INTEGER | read-write | This object indicates the deletion of the global GTSM configurations. Options: 1. delete(1) -indicates that global GTSM configurations are to be deleted. 2. ready(2) -indicates that it is ready to delete global GTSM configurations. |
| INT hwMplsFrrLspTrigger | 1.3.6.1.4.1.2011.5.25.143.1.26 | INTEGER | read-write | This object indicates the way to configure the LDP policy of global instance for LDP Auto FRR. Options: 1. all(1) -indicates that all FECs are triggered for the IGP. 2. none(2) -indicates that no FEC is triggered for the IGP. 3. host(3) -indicates that the host FEC is triggered for the IGP. 4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP. If the object is set as ipprefix, the value of hwMplsFrrLspTriggerIpPrefix must be set together. Default: host |
| OCT hwMplsFrrLspTriggerIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.27 | OCTET STRING | read-write | This object indicates the IP prefix when configuring LDP Auto FRR for the public network instance. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsFrrLspTrigger must be set as ipprefix. |
| I32 hwLdpBackOffTimerInit | 1.3.6.1.4.1.2011.5.25.143.1.28 | Integer32 | read-write | This object indicates the initial value of backoff timer. Default: 15 Unit: seconds |
| I32 hwLdpBackOffTimerMax | 1.3.6.1.4.1.2011.5.25.143.1.29 | Integer32 | read-write | This object indicates the maximum value of backoff timer. Default: 120 Unit: seconds |
| ENA hwLdpLongestMatch | 1.3.6.1.4.1.2011.5.25.143.1.30 | EnabledStatus | read-write | This object indicates that the LDP is enabled with the function of searching for routes according to the longest match rule to establish LSPs. Default: disabled |
| ENA hwLdpRemotePeerAutoDodRequest | 1.3.6.1.4.1.2011.5.25.143.1.37 | EnabledStatus | read-write | The value of this object identifies whether the remote peer is globally enabled with the capability of automatically sending a DoD request. |
| ENA hwLdpCapabilityAnnouncementConfig | 1.3.6.1.4.1.2011.5.25.143.1.38 | EnabledStatus | read-write | The value of this object identifies whether LDP has Capability-Announcement ability. |
| hwLdpVpnTable | 1.3.6.1.4.1.2011.5.25.143.1.50 | not-accessible | This object is used to configure or delete the LDP multi-instance. The index of this table is hwLdpVpnInstanceId. Make sure the relevant VPN instance is already created. | |
| hwLdpVpnEntry | 1.3.6.1.4.1.2011.5.25.143.1.50.1 | not-accessible | This object is used to configure or delete the LDP multi-instance. The index of this entry is hwLdpVpnInstanceId. Make sure the relevant VPN instance is already created. | |
| U32 hwLdpVpnInstanceId | 1.3.6.1.4.1.2011.5.25.143.1.50.1.1 | Unsigned32 | not-accessible | This object indicates the ID of the VPN instance. You can find the correct VPN instance ID based on hwL3vpnVrfIndex of hwL3vpnStatisticsTable. |
| IP hwLdpVpnLsrId | 1.3.6.1.4.1.2011.5.25.143.1.50.1.11 | IpAddress | read-create | This object indicates the way to configure the LDP LSR ID. If the value of the LDP LSR ID is the same as the value of the MPLS LSR ID, the LDP LSR ID is deleted. It is recommended not to change the LDP LSR ID unless necessary. |
| ENA hwLdpVpnSplitHorizonAll | 1.3.6.1.4.1.2011.5.25.143.1.50.1.12 | EnabledStatus | read-create | This object indicates the way to set the flag of split horizon for all LDP VPN peers. Default: disabled |
| INT hwLdpVpnReset | 1.3.6.1.4.1.2011.5.25.143.1.50.1.13 | INTEGER | read-create | This object indicates the reset of the LDP multi-instance corresponding to the VPN. Options: 1.reset(1) -indicates that the LDP multi-instance will be reset. 2.ready(2) -indicates that it is ready to reset ldp multi-instance. This value cannot be set. |
| INT hwMplsVpnFrrLspTrigger | 1.3.6.1.4.1.2011.5.25.143.1.50.1.14 | INTEGER | read-create | This object indicates the way to configure the LDP policy of vpn instance for LDP Auto FRR. Options: 1. all(1) -indicates that all FECs are triggered for the IGP. 2. none(2) -indicates that no FEC is triggered for the IGP. 3. host(3) -indicates that the host FEC is triggered for the IGP. 4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP. If the object is set as ipprefix, the value of hwMplsVpnFrrLspTriggerIpPrefix must be set together. |
| OCT hwMplsVpnFrrLspTriggerIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.50.1.15 | OCTET STRING | read-create | This object indicates the IP prefix when configuring the LDP policy of vpn instance for LDP Auto FRR. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsVpnFrrLspTrigger must be set as ipprefix. |
| ENA hwLdpVpnGracefulDeleteCapability | 1.3.6.1.4.1.2011.5.25.143.1.50.1.16 | EnabledStatus | read-create | This object indicates whether the LDP graceful-delete capability is enabled for a VPN instance. |
| I32 hwLdpVpnGracefulDeleteTimer | 1.3.6.1.4.1.2011.5.25.143.1.50.1.17 | Integer32 | read-create | The value of this object identifies the value of a graceful-delete timer for a VPN instance. When the status of hwLdpVpnGracefulDeleteCapability is enabled, the default value returned by the object is valid. Default: 5 Unit: seconds |
| ROW hwLdpVpnRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.50.1.51 | RowStatus | read-create | This object indicates whether one entry of hwLdpVpnTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. |
| hwLdpRemoteEntityTable | 1.3.6.1.4.1.2011.5.25.143.1.51 | not-accessible | This object is used to configure or delete the LDP remote peer. The index of this table is hwLdpRemoteName. | |
| hwLdpRemoteEntityEntry | 1.3.6.1.4.1.2011.5.25.143.1.51.1 | not-accessible | This object is used to configure or delete the LDP remote peer. The index of this entry is hwLdpRemoteName. | |
| STR hwLdpRemoteName | 1.3.6.1.4.1.2011.5.25.143.1.51.1.1 | DisplayString | not-accessible | This object indicates the name of the LDP remote peer. Range: 1-32 characters |
| IP hwLdpRemoteIp | 1.3.6.1.4.1.2011.5.25.143.1.51.1.11 | IpAddress | read-create | This object indicates the configuration of the remote peer LSR ID. If being set, the ID cannot be modified. To modify the ID, delete the original ID and create a new one. If the ID is set as 0.0.0.0, it indicates that the ID is deleted. |
| ENA hwLdpRemotePwe3 | 1.3.6.1.4.1.2011.5.25.143.1.51.1.12 | EnabledStatus | read-create | This object indicates the configuration or deletion of the policy for the remote LDP session. When the object is enabled, it is forbidden to send the mapping message to the remote peer. Default: disabled |
| I32 hwLdpRemoteKeepaliveTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.13 | Integer32 | read-create | This object indicates the value of LDP Keepalive timer. Default: 45 Unit: seconds |
| I32 hwLdpRemoteHelloTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.14 | Integer32 | read-create | This object indicates the value of LDP Hello hold timer. Default: 45 Unit: seconds |
| I32 hwLdpRemoteKeepaliveSendTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.15 | Integer32 | read-create | This object indicates the value of LDP Keepalive send timer. By default, the value of the timer is 0, configuration does not take effect. Default: 0 Unit: seconds |
| I32 hwLdpRemoteHelloSendTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.16 | Integer32 | read-create | This object indicates the value of LDP Hello send timer. By default, the value of the timer is 0, configuration does not take effect. Default: 0 Unit: seconds |
| I32 hwLdpRemoteIgpSyncTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.17 | Integer32 | read-create | This object indicates the value of IGP-Sync timer. Default: 10 Unit: seconds |
| ENA hwLdpRemoteIpAutoDoDRequest | 1.3.6.1.4.1.2011.5.25.143.1.51.1.18 | EnabledStatus | read-create | This object identifies whether the remote peer is enabled with the capability of automatically sending a DoD request. Default: disabled |
| ENA hwLdpRemoteIpAutoDoDRequestBlock | 1.3.6.1.4.1.2011.5.25.143.1.51.1.19 | EnabledStatus | read-create | This object indicates whether the remote ip auto dod request function blocked. Default: disabled |
| INT hwLdpRemoteLabelAdvertisementMode | 1.3.6.1.4.1.2011.5.25.143.1.51.1.20 | INTEGER | read-create | This object indicates the label distribution mode. Options: 1. dod(1) -indicates that the label distribution mode is dod. 2. du(2) -indicates that the label distribution mode is du. Default: du |
| NUM hwLdpRemoteLocalLsrIdIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.51.1.21 | InterfaceIndexOrZero | read-create | This object indicates the way to specify the interface that the local LDP LSR-ID based on remote entity is assigned to. Value: 0..2147483647 The default value of the object is the interface that the global LDP LSR ID is assigned to. If the global LDP LSR ID is not assigned to any interface, then the value of the object is 0. If set 0, the value of the object will be the default value. |
| ROW hwLdpRemoteRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.51.1.51 | RowStatus | read-create | This object indicates whether one entry of hwLdpRemoteEntityTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. |
| hwLdpPeerTable | 1.3.6.1.4.1.2011.5.25.143.1.52 | not-accessible | This object is used to configure the LDP peer. The index of this table is hwLdpPeerLsrId. | |
| hwLdpPeerEntry | 1.3.6.1.4.1.2011.5.25.143.1.52.1 | not-accessible | An entry of the peer feature table, used to configure and display features, such as the MD5 password and split horizon policy negotiated with the local peer. The index of this entry is hwLdpPeerLsrId. | |
| IP hwLdpPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.52.1.1 | IpAddress | not-accessible | This object indicates the LSR ID of the LDP peer. |
| INT hwLdpPeerMd5Type | 1.3.6.1.4.1.2011.5.25.143.1.52.1.11 | INTEGER | read-create | This object indicates the Md5 type. Options: 1. cipher(1) -indicates that the MD5 password is in cipher text mode. 2. plain(2) -indicates that the MD5 password is in plain text mode. 3. null(3) -indicates that the MD5 type is null, which means that the MD5 authentication is not configured for the LDP peer. |
| OCT hwLdpPeerMd5Password | 1.3.6.1.4.1.2011.5.25.143.1.52.1.12 | OCTET STRING | read-create | This object indicates the MD5 password of LDP neighbor. To delete the password, set the password length as zero. When read, it always returns an Octet string with the length of zero. |
| I32 hwLdpPeerGtsmHops | 1.3.6.1.4.1.2011.5.25.143.1.52.1.13 | Integer32 | read-create | This object indicates the number of GTSM hops. The valid number of GTSM hops ranges from 1 to 255. To clear the configuration of GTSM hops, set the number of GTSM hops as 0. |
| ENA hwLdpPeerSplitHorizon | 1.3.6.1.4.1.2011.5.25.143.1.52.1.14 | EnabledStatus | read-create | This object indicates the way to set the flag of split horizon for the specified LDP peer. Default: disabled |
| INT hwLdpPeerReset | 1.3.6.1.4.1.2011.5.25.143.1.52.1.15 | INTEGER | read-create | This object indicates the reset of the neighbor services. Options: 1. reset(1) -indicates that the neighbor services will be reset. Only when the object is ready, can this value take effect. 2. ready(2) -indicates that it is ready to reset the neighbor services. This value cannot be set. |
| OCT hwLdpPeerKeychainName | 1.3.6.1.4.1.2011.5.25.143.1.52.1.18 | OCTET STRING | read-create | This object indicates the Keychain name. To cancel the Keychain authentication, set the Keychain name length as 0. |
| INT hwLdpPeerOutBoundPolicyRange | 1.3.6.1.4.1.2011.5.25.143.1.52.1.19 | INTEGER | read-create | This object indicates the range of IGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerOutBoundPolicyFecIpPrefix must be set together. |
| OCT hwLdpPeerOutBoundPolicyFecIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.52.1.20 | OCTET STRING | read-create | This object indicates the IP prefix list name of IGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerOutBoundPolicyRange must be set as ipprefix. |
| INT hwLdpPeerOutBoundPolicyBgpRange | 1.3.6.1.4.1.2011.5.25.143.1.52.1.21 | INTEGER | read-create | This object indicates the range of BGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerOutBoundPolicyBgpIpPrefix must be set together. |
| OCT hwLdpPeerOutBoundPolicyBgpIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.52.1.22 | OCTET STRING | read-create | This object indicates the IP prefix list name of BGP routes for the outbound policy. If the object is set with a value, the value of hwLdpPeerOutBoundPolicyBgpRange must be set as ipprefix. |
| INT hwLdpPeerInBoundPolicyRange | 1.3.6.1.4.1.2011.5.25.143.1.52.1.23 | INTEGER | read-create | This object indicates the route range for the inbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerInBoundPolicyFecIpPrefix must be set together. |
| OCT hwLdpPeerInBoundPolicyFecIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.52.1.24 | OCTET STRING | read-create | This object indicates the IP prefix list name for the inbound policy. If the object is set with a value, the value of hwLdpPeerInBoundPolicyRange must be set as ipprefix. |
| ROW hwLdpPeerRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.52.1.51 | RowStatus | read-create | This object indicates whether one entry of hwLdpPeerTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. |
| hwLdpVpnPeerTable | 1.3.6.1.4.1.2011.5.25.143.1.53 | not-accessible | This table is used to create and delete peer configurations in the LDP multi-instance. The indexs of this table are hwLdpVpnInstanceId, hwLdpVpnPeerLsrId. Make sure the corresponding LDP VPN-instance is already created in hwLdpVpnTable. | |
| hwLdpVpnPeerEntry | 1.3.6.1.4.1.2011.5.25.143.1.53.1 | not-accessible | An entry of the VPN peer feature table, used to configure and display features, such as the MD5 password and split horizon policy negotiated with the local peer on the VPN. The indexs of this entry are hwLdpVpnInstanceId, hwLdpVpnPeerLsrId. Make sure the corresponding LDP VPN-instance is already created in hwLdpVpnTable. | |
| IP hwLdpVpnPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.53.1.1 | IpAddress | not-accessible | This object indicates the LSR ID of the LDP peer. |
| INT hwLdpVpnPeerMd5Type | 1.3.6.1.4.1.2011.5.25.143.1.53.1.11 | INTEGER | read-create | This object indicates the Md5 type. 1. cipher(1) -indicates that the MD5 password is in cipher text mode. 2. plain(2) -indicates that the MD5 password is in plain text mode. 3. null(3) -indicates that the MD5 type is null, which means that the MD5 authentication is not configured for the LDP peer. |
| OCT hwLdpVpnPeerMd5Password | 1.3.6.1.4.1.2011.5.25.143.1.53.1.12 | OCTET STRING | read-create | This object indicates the MD5 password of VPN LDP neighbor. To delete the password, set the password length as zero. When read, it always returns an Octet string with the length of zero. |
| ENA hwLdpVpnPeerSplitHorizon | 1.3.6.1.4.1.2011.5.25.143.1.53.1.13 | EnabledStatus | read-create | This object indicates the way to set the flag of split horizon for the specified LDP peer. Default: disabled |
| INT hwLdpVpnPeerReset | 1.3.6.1.4.1.2011.5.25.143.1.53.1.14 | INTEGER | read-create | This object indicates the reset of the neighbor services. Options: 1. reset(1) -indicates that the neighbor services will be reset. Only when the object is ready, can this value take effect. 2. ready(2) -indicates that it is ready to reset the neighbor services. This value cannot be set. |
| OCT hwLdpVpnPeerKeychainName | 1.3.6.1.4.1.2011.5.25.143.1.53.1.17 | OCTET STRING | read-create | This object indicates the Keychain name. To cancel the Keychain authentication, set the Keychain name length as 0. |
| ROW hwLdpVpnPeerRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.53.1.51 | RowStatus | read-create | This object indicates whether one entry of hwLdpVpnPeerTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. |
| hwLdpInterfaceTable | 1.3.6.1.4.1.2011.5.25.143.1.54 | not-accessible | This table is used to configure or delete the LDP capability on the interface. The index of this table is hwLdpInterfaceIndex. | |
| hwLdpInterfaceEntry | 1.3.6.1.4.1.2011.5.25.143.1.54.1 | not-accessible | An entry of the LDP interface table, used to configure and display the LDP negotiation parameters on the interface enabled with LDP capabilities. The index of this entry is hwLdpInterfaceIndex. | |
| NUM hwLdpInterfaceIndex | 1.3.6.1.4.1.2011.5.25.143.1.54.1.1 | InterfaceIndex | not-accessible | This object indicates the interface index. You can get the correct interface index based on ifIndex of ifTable. |
| I32 hwLdpStaticFrrProtectTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.11 | Integer32 | read-create | This object indicates the value of static FRR protect timer. Default: 10 Unit: seconds |
| I32 hwLdpKeepAliveTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.12 | Integer32 | read-create | This object indicates the value of Keepalive timer. Default: 45 Unit: seconds |
| I32 hwLdpIgpSyncTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.13 | Integer32 | read-create | This object indicates the value of IGP-Sync timer. By default, the timer is set to 10 seconds. Default: 10 Unit: seconds |
| I32 hwLdpHelloTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.14 | Integer32 | read-create | This object indicates the value of Hello hold timer. By default, the value of the timer is 15 seconds. Default: 15 Unit: seconds |
| NUM hwLdpTransportAddressIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.54.1.15 | InterfaceIndexOrZero | read-create | This object indicates the way to specify the interface that the Transport Address is assigned to. Value: 0..2147483647 The default value of the object for the public interface is the interface that the LDP LSR ID is assigned to. If the LDP LSR ID is not assigned to any interface, then the value of the object is 0, and 0 cannot be set. The default value of the object for the private interface is the private interface itself. Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN. The interface must be bound with the same VPN instance. |
| I32 hwLdpKeepAliveSendTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.16 | Integer32 | read-create | This object indicates the value of LDP Keepalive send timer. Default: 0 Unit: seconds |
| I32 hwLdpHelloSendTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.17 | Integer32 | read-create | This object indicates the value of LDP Hello send timer. Default: 0 Unit: seconds |
| INT hwLdpInterfaceLabelAdvertisementMode | 1.3.6.1.4.1.2011.5.25.143.1.54.1.18 | INTEGER | read-create | This object indicates the label distribution mode. Options: 1. dod(1) -indicates that the label distribution mode is dod. 2. du(2) -indicates that the label distribution mode is du. Default: du |
| NUM hwLdpInterfaceLocalLsrIdIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.54.1.19 | InterfaceIndexOrZero | read-create | This object indicates the way to specify the interface that the local LDP LSR-ID based on interface is assigned to. Value: 0..2147483647 The default value of the object for the public interface is the interface that the global LDP LSR ID is assigned to. If the global LDP LSR ID is not assigned to any interface, then the value of the object is 0. If set 0, the value of the object will be the default value. The default value of the object for the private interface is the interface that the global LDP LSR ID of VPN Instance is assigned to. Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN. The interface which the object specified must be bound with the same VPN instance with the interface which is configured. |
| ROW hwLdpInterfaceRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.54.1.51 | RowStatus | read-create | This object indicates whether one entry of hwLdpInterfaceTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. |
| hwLdpPeerGroupTable | 1.3.6.1.4.1.2011.5.25.143.1.58 | not-accessible | This table is used to configure an LDP peer group. | |
| hwLdpPeerGroupEntry | 1.3.6.1.4.1.2011.5.25.143.1.58.1 | not-accessible | An entry of this table. | |
| OCT hwLdpPeerGroupName | 1.3.6.1.4.1.2011.5.25.143.1.58.1.1 | OCTET STRING | not-accessible | This object indicates the name of a peer group. |
| INT hwLdpPeerGroupOutBoundRange | 1.3.6.1.4.1.2011.5.25.143.1.58.1.11 | INTEGER | read-create | This object indicates the range of IGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupOutBoundFecIpPrefix must be set together. |
| OCT hwLdpPeerGroupOutBoundFecIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.58.1.12 | OCTET STRING | read-create | This object indicates the IP prefix list name of IGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerGroupOutBoundRange must be set as ipprefix. |
| INT hwLdpPeerGroupOutBoundBgpRange | 1.3.6.1.4.1.2011.5.25.143.1.58.1.13 | INTEGER | read-create | This object indicates the range of BGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupOutBoundBgpIpPrefix must be set together. |
| OCT hwLdpPeerGroupOutBoundBgpIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.58.1.14 | OCTET STRING | read-create | This object indicates the IP prefix list name of BGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerGroupOutBoundBgpRange must be set as ipprefix. |
| INT hwLdpPeerGroupInBoundRange | 1.3.6.1.4.1.2011.5.25.143.1.58.1.15 | INTEGER | read-create | This object indicates the route range for an inbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupInBoundIpPrefix must be set together. |
| OCT hwLdpPeerGroupInBoundIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.58.1.16 | OCTET STRING | read-create | This object indicates the IP prefix list name of routes for an inbound policy. If the object is set with a value, the value of hwLdpPeerGroupInBoundRange must be set as ipprefix. |
| ROW hwLdpPeerGroupRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.58.1.51 | RowStatus | read-create | This object indicates whether one entry of hwLdpPolicyPeerGroupTable is created or destroyed. The value of this object is CreatAndGo or Destroy. When the value of the object is set to CreatAndGo, and the entry is correctly created, the status of the object will change into active. |
| INT hwLdpOutBoundPolicyPeerAllRange | 1.3.6.1.4.1.2011.5.25.143.1.59 | INTEGER | read-write | This object indicates the range of IGP routes for a global outbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpOutBoundPolicyPeerAllFecIpPrefix must be set together. |
| OCT hwLdpOutBoundPolicyPeerAllFecIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.60 | OCTET STRING | read-write | This object indicates the IP prefix list name of IGP routes for a global outbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpOutBoundPolicyPeerAllRange must be set as ipprefix. |
| INT hwLdpOutBoundPolicyPeerAllBgpRange | 1.3.6.1.4.1.2011.5.25.143.1.61 | INTEGER | read-write | This object indicates the range of BGP routes for a global outbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpOutBoundPolicyPeerAllBgpIpPrefix must be set together. |
| OCT hwLdpOutBoundPolicyPeerAllBgpIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.62 | OCTET STRING | read-write | This object indicates the IP prefix list name of BGP routes for a global outbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpOutBoundPolicyPeerAllBgpRange must be set as ipprefix. |
| INT hwLdpInBoundPolicyPeerAllRange | 1.3.6.1.4.1.2011.5.25.143.1.63 | INTEGER | read-write | This object indicates the range of routes for a global inbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpInBoundPolicyPeerAllIpPrefix must be set together. |
| OCT hwLdpInBoundPolicyPeerAllIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.64 | OCTET STRING | read-write | This object indicates the IP prefix list name of routes for a global inbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpInBoundPolicyPeerAllRange must be set as ipprefix. |
| ENA hwLdpGracefulDeleteCapability | 1.3.6.1.4.1.2011.5.25.143.1.65 | EnabledStatus | read-write | This object indicates whether the LDP graceful-delete capability is enabled. |
| I32 hwLdpGracefulDeleteTimer | 1.3.6.1.4.1.2011.5.25.143.1.66 | Integer32 | read-write | The value of this object identifies the value of a graceful-delete timer. When the status of hwLdpGracefulDeleteCapability is enabled, the default value returned by the object is valid. Default: 5 Unit: seconds |
| INT hwLdpLspDownReason | 1.3.6.1.4.1.2011.5.25.143.1.67 | INTEGER | accessible-for-notify | The LDP LSP down reason. Options: 1. other(1) -indicates other reasons. 2. session down(2) -indicates the ldp session went down. 3. route change(3) -indicates the route changed. 4. cannot recovery from GR(4) -indicates LSP cannot recovery from graceful-restart. 5. policy change(5) -indicates the policy changed. |
| OID hwLdpLspDownMplsLsrId | 1.3.6.1.4.1.2011.5.25.143.1.68 | MplsLsrIdentifier | accessible-for-notify | This object indicates the LSR ID of failed router. |
| NUM hwLdpLspDownOutIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.69 | InterfaceIndex | accessible-for-notify | This object indicates the outgoing interface index of the failed router. |
| IP hwLdpLspDownOutIfMainIp | 1.3.6.1.4.1.2011.5.25.143.1.70 | IpAddress | accessible-for-notify | This object indicates the main ip address of the failed router's outgoing interface. |
| INT hwLdpLspDownOutIfState | 1.3.6.1.4.1.2011.5.25.143.1.71 | INTEGER | accessible-for-notify | The state of the failed router's outgoing interface. Options: 1. up(1) -indicates that the state of the outgoing interface is Up. 2. down(2) -indicates that the state of the outgoing interface is Down. |
| OID hwLdpLspDownDownstreamPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.72 | MplsLdpIdentifier | accessible-for-notify | This object indicates the failed router's downstream peer's LSR ID. |
| hwLdpSessionStatistics | 1.3.6.1.4.1.2011.5.25.143.1.73 | |||
| I32 hwLdpLocalOperationalSessionNumber | 1.3.6.1.4.1.2011.5.25.143.1.73.1 | Integer32 | read-only | This object indicates the number of local LDP operational sessions. |
| I32 hwLdpRemoteOperationalSessionNumber | 1.3.6.1.4.1.2011.5.25.143.1.73.2 | Integer32 | read-only | This object indicates the number of remote LDP operational sessions. |
| I32 hwLdpLocalAndRemoteOperationalSessionNumber | 1.3.6.1.4.1.2011.5.25.143.1.73.3 | Integer32 | read-only | This object indicates the number of local and remote LDP operational sessions. |
| I32 hwLdpTotalOperationalSessionNumber | 1.3.6.1.4.1.2011.5.25.143.1.73.4 | Integer32 | read-only | This object indicates the total number of LDP operational sessions. |
| hwMplsLdpTrap | 1.3.6.1.4.1.2011.5.25.143.2 | |||
| NTF hwMplsLdpSessionDown | 1.3.6.1.4.1.2011.5.25.143.2.1 | When the trap indicating that a session is down is sent, the cause for the down LDP session is displayed. | ||
| NTF hwMplsLdpLspDown | 1.3.6.1.4.1.2011.5.25.143.2.2 | When the trap indicating that a session is down is sent, the cause for the down LSP session is displayed. | ||
| NTF hwMplsLdpHostIngressLspDownClear | 1.3.6.1.4.1.2011.5.25.143.2.3 | A trap is sent to clear the down trap of a specified FEC's ingress lsp. | ||
| NTF hwMplsLdpHostIngressLspDown | 1.3.6.1.4.1.2011.5.25.143.2.4 | A trap is sent when all the ingress lsp of a specified FEC went down. | ||
| hwMplsLdpConformance | 1.3.6.1.4.1.2011.5.25.143.3 | |||
| hwMplsLdpCompliances | 1.3.6.1.4.1.2011.5.25.143.3.1 | The Compliance statement for systems supporting the HUAWEI-MPLSLDP-MIB. | ||
| hwMplsLdpGroup | 1.3.6.1.4.1.2011.5.25.143.3.2 | |||
| hwMplsLdpInfoGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.1 | Infomation about LDP LSP. | ||
| hwMplsLdpNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.2 | Notification information included in the mib. | ||
| hwMplsLdpLspDownNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.3 | No use. | ||
| hwMplsLdpGlobalGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.4 | Information about Ldp Global configuration. | ||
| hwMplsLdpVpnGlobalGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.5 | Information about Ldp Vpn configuration. | ||
| hwMplsLdpRemoteEntityGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.6 | Information about remote entity. | ||
| hwMplsLdpPeerGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.7 | Information about Ldp Peer. | ||
| hwMplsLdpVpnPeerGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.8 | Information about Ldp Vpn Peer. | ||
| hwMplsLdpInterfaceGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.9 | Information about Ldp interface capability. | ||
| hwLdpLspDownReasonGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.10 | Information about Ldp ingress Lsp down reason. | ||
| hwMplsLdpHostIngressLspDownNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.11 | Notification information included in the mib. | ||
| hwLdpPolicyPeerGroupGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.15 | Information about Ldp Policies of peer groups. | ||
| hwMplsLdpFrrProtectGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.16 | Information about Ldp FRR protect timer. | ||
| hwMplsLdpSessionStatisticsGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.17 | Information about Ldp Session Statistics. |
RFC description
Huawei MPLS LDP (Label Distribution Protocol) MIB for managing label distribution, session negotiation, and LSP establishment on Huawei devices.
Start monitoring Huawei MPLS router (LDP peer/session/hello-adjacency state) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.