HUAWEI-MPLS-TP-MIB

All MIBs › HUAWEI-MPLS-TP-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2012--0-3-

Category: MPLS and Traffic Engineering, Vendor: Huawei

Description: Huawei MPLS-TP (Transport Profile) MIB for managing MPLS-TP LSPs, sections, paths, and OAM configurations.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-MPLS-TP-MIB?

HUAWEI-MPLS-TP-MIB is a Huawei private extension MIB for MPLS Transport Profile (MPLS-TP), a connection-oriented packet transport technology used in carrier transport networks, covering LSPs, sections, paths, and OAM (Operations, Administration and Maintenance) configuration. It exposes configuration data for transport paths/tunnels and fault-oriented trap definitions for MPLS-TP events. Its monitoring value is primarily network-path software status: the operational state of LSPs/paths, OAM continuity-check results, and traps signaling a path failure or protection event, which reflect the health of the transport tunnels themselves rather than physical hardware sensors. It is explicitly a private extension of the broader MPLS-TP standard (as defined by IETF/ITU-T) and is meant to be used alongside standard MPLS-related MIBs. It is deployed on Huawei PTN (Packet Transport Network) routers/switches carrying deterministic, carrier-grade transport services over MPLS-TP. Engineers can download the HUAWEI-MPLS-TP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-MPLS-TP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei PTN (Packet Transport Network) routers
Huawei MPLS-TP capable routers/switches

Monitoring Examples

No sample object names were provided for this module. Based on the module description, an administrator would monitor per-LSP or per-path operational status and OAM continuity-check/alarm objects to detect an MPLS-TP tunnel defect or failure that triggers -- or fails to trigger -- a protection switchover, which would otherwise show up as a silent service outage on that transport path.

What Can Be Monitored

LSP/path operational status
section and path configuration
OAM continuity-check results
protection switchover events
LSP/path fault traps

Imported Objects

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From IF-MIB

ifIndex	OBJECT-TYPE
ifName	OBJECT-TYPE

From MPLS-TC-STD-MIB

MplsExtendedTunnelId
MplsTunnelIndex
MplsTunnelInstanceIndex

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

BITS
Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwMplsTpMib	1.3.6.1.4.1.2011.5.25.305			This MIB is used for defining the HUAWEI private extended Transport Profile of Multiprotocol Label Switching (MPLS-TP) MIB object. All MIB objects are used to describe private managed objects and trap definitions for MPLS-TP.
hwMplsTpObjects	1.3.6.1.4.1.2011.5.25.305.1
hwMplsTpTables	1.3.6.1.4.1.2011.5.25.305.1.1
hwMplsTpTunnelTable	1.3.6.1.4.1.2011.5.25.305.1.1.1		not-accessible	A tp-tunnel needs to be uniquely identified across an MPLS-TP network. Indexes hwMplsTpTunnelIngressIndex, hwMplsTpTunnelIngressLSRId, hwMplsTpIngressGlobalId, hwMplsTpTunnelEgressIndex, hwMplsTpTunnelEgressLSRId and hwMplsTpEgressGlobalId uniquely identifies a tunnel across an MPLS-TP network. The indexes of this table are hwMplsTpTunnelIngressIndex, hwMplsTpTunnelIngressLSRId, hwMplsTpIngressGlobalId, hwMplsTpTunnelEgressIndex, hwMplsTpTunnelEgressLSRId and hwMplsTpEgressGlobalId.
hwMplsTpTunnelEntry	1.3.6.1.4.1.2011.5.25.305.1.1.1.1		not-accessible	A tp-tunnel needs to be uniquely identified across an MPLS-TP network. Indexes hwMplsTpTunnelIngressIndex, hwMplsTpTunnelIngressLSRId, hwMplsTpIngressGlobalId, hwMplsTpTunnelEgressIndex, hwMplsTpTunnelEgressLSRId and hwMplsTpEgressGlobalId uniquely identifies a tunnel across an MPLS-TP network. The indexes of this entry are hwMplsTpTunnelIngressIndex, hwMplsTpTunnelIngressLSRId, hwMplsTpIngressGlobalId, hwMplsTpTunnelEgressIndex, hwMplsTpTunnelEgressLSRId and hwMplsTpEgressGlobalId.
MPL hwMplsTpTunnelIngressIndex	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.1	MplsTunnelIndex	not-accessible	Identity of the ingress LSR associated with this tunnel instance. This value SHOULD be equal to the Tunnel Sender Address in the Sender Template object and MAY be equal to the Extended Tunnel Id field in the SESSION object.
MPL hwMplsTpTunnelIngressLSRId	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.2	MplsExtendedTunnelId	not-accessible	Identity of the ingress LSR associated with this tp-tunnel instance.
I32 hwMplsTpIngressGlobalId	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.3	Integer32	not-accessible	The GlobalId is defined to uniquely identify an Ingress LSR operator.This Value idefines a globally unique Attachment Interface Identifier (AII). That AII is composed of three parts: a Global_ID that uniquely identifies an operator, a prefix, and, finally, an attachment circuit identifier.
MPL hwMplsTpTunnelEgressIndex	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.4	MplsTunnelIndex	not-accessible	Identity of the egress LSR associated with this tunnel instance.
MPL hwMplsTpTunnelEgressLSRId	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.5	MplsExtendedTunnelId	not-accessible	Identity of the egress LSR associated with this tunnel instance.
I32 hwMplsTpEgressGlobalId	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.6	Integer32	not-accessible	The GlobalId is defined to uniquely identify an Ingress LSR operator.This Value idefines a globally unique Attachment Interface Identifier (AII). That AII is composed of three parts: a Global_ID that uniquely identifies an operator, a prefix, and, finally, an attachment circuit identifier.
STR hwMplsTpTunnelIfName	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.7	SnmpAdminString	read-only	Indicates the tp-tunnel interface name. The object is only valid at the ingress.
INT hwMplsTpTunnelAdminStatus	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.8	INTEGER	read-only	Indicates the management status of this tunnel.Reference to MPLS-TE-STD-MIB. Options: 1. up(1) -indicates the management status of this tunnel is up. 2. down(2) -indicates the management status of this tunnel is down. 3. testing(3) -indicates the tunnel is used in some test mode.
INT hwMplsTpTunnelOperStatus	1.3.6.1.4.1.2011.5.25.305.1.1.1.1.9	INTEGER	read-only	Indicates the actual operational status of this tunnel, which is but not limited to the status of this tunnel of a certain period.Reference to MPLS-TE-STD-MIB. Options: 1. up(1) -indicates that the operational status of this tunnel is up. 2. down(2) -indicates that the operational status of this tunnel is down. 3. testing(3) -indicates that the tunnel is used in some test mode. 4. unknown(4) -indicates the invalid value. 5. dormant(5) -indicates that the status can not be determined. 6. notPresent(6) -indicates that some component is missing 7. lowerLayerDown(7) -indicates the Down state due to the state of lower layer interfaces.
hwMplsTpLspTable	1.3.6.1.4.1.2011.5.25.305.1.1.2		not-accessible	A table of all TP lsps seen by a given sys-tem.
hwMplsTpLspEntry	1.3.6.1.4.1.2011.5.25.305.1.1.2.1		not-accessible	An entry in this table represents information on a single TP LSP which is represented by a session's index triple (hwMplsTpTunnelIngressInstance, hwMplsTpTunnelEgressInstance, hwMplsTpLspType).
MPL hwMplsTpTunnelIngressInstance	1.3.6.1.4.1.2011.5.25.305.1.1.2.1.1	MplsTunnelInstanceIndex	accessible-for-notify	Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs.
MPL hwMplsTpTunnelEgressInstance	1.3.6.1.4.1.2011.5.25.305.1.1.2.1.2	MplsTunnelInstanceIndex	accessible-for-notify	Uniquely identifies a particular instance of a tunnel between a pair of egress and ingress LSRs.
INT hwMplsTpLspType	1.3.6.1.4.1.2011.5.25.305.1.1.2.1.3	INTEGER	accessible-for-notify	The type of LSP connection. Options: 1. protection(1) -indicates that the lsp type of this tunnel is protection lsp. 2. working(2) -indicates that the lsp type of this tunnel is working lsp.
hwMplsTpGlobalObjects	1.3.6.1.4.1.2011.5.25.305.1.2
hwMplsTpNotifications	1.3.6.1.4.1.2011.5.25.305.2
hwMplsTpTrapObjects	1.3.6.1.4.1.2011.5.25.305.2.1
hwMplsTpTunnelTrap	1.3.6.1.4.1.2011.5.25.305.2.2
NTF hwMplsTpTunnelDownClear	1.3.6.1.4.1.2011.5.25.305.2.2.1			This notification is generated when a mplsTpTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsTpTunnelOperStatus.
NTF hwMplsTpTunnelDown	1.3.6.1.4.1.2011.5.25.305.2.2.2			This notification is generated when a mplsTpTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the included value of mplsTpTunnelOperStatus.
NTF hwMplsTpTunnelResume	1.3.6.1.4.1.2011.5.25.305.2.2.3			This object is used to indicate that data switching from protection Lsp to Working Lsp.
NTF hwMplsTpTunnelSwitch	1.3.6.1.4.1.2011.5.25.305.2.2.4			This object is used to indicate that data switching from protection Lsp to Working Lsp.
hwMplsTpLspTrap	1.3.6.1.4.1.2011.5.25.305.2.3
NTF hwMplsTpLspOamDlocClear	1.3.6.1.4.1.2011.5.25.305.2.3.1			This object indicates that the link recovers from a connectivity fault.
NTF hwMplsTpLspOamDloc	1.3.6.1.4.1.2011.5.25.305.2.3.2			This object is used to indicates the connectivity fault of the link.
NTF hwMplsTpLspOamRdiClear	1.3.6.1.4.1.2011.5.25.305.2.3.3			This object indicates that the link recovers from a remote defect.
NTF hwMplsTpLspOamRdi	1.3.6.1.4.1.2011.5.25.305.2.3.4			This object is used to indicates the remote defect of the link.
NTF hwMplsTpLspOamMisconnectionEncapClear	1.3.6.1.4.1.2011.5.25.305.2.3.5			This object indicates that the link recovers from an misconnection encap defect.
NTF hwMplsTpLspOamMisconnectionEncap	1.3.6.1.4.1.2011.5.25.305.2.3.6			This object indicates that the link receivs from an misconnection encap defect.
NTF hwMplsTpLspOamMisconnectionDiscrClear	1.3.6.1.4.1.2011.5.25.305.2.3.7			This object indicates that the link recovers from an misconnection discription defect.
NTF hwMplsTpLspOamMisconnectionDiscr	1.3.6.1.4.1.2011.5.25.305.2.3.8			This object indicates that the link receivs from an misconnection discription defect.
NTF hwMplsTpLspOamMisconnectionMEPClear	1.3.6.1.4.1.2011.5.25.305.2.3.9			This object indicates that the link recovers from an unexpect MEG-ID defect.
NTF hwMplsTpLspOamMisconnectionMEP	1.3.6.1.4.1.2011.5.25.305.2.3.10			This object indicates the link receivs an unexpect MEG-ID defect.
NTF hwMplsTpLspOamMisconnectionSECClear	1.3.6.1.4.1.2011.5.25.305.2.3.11			This object indicates that the link recovers from an Misconnection SEC defect .
NTF hwMplsTpLspOamMisconnectionSEC	1.3.6.1.4.1.2011.5.25.305.2.3.12			This object indicates that the link receivs from an Misconnection SEC defect.
hwMplsTpConformance	1.3.6.1.4.1.2011.5.25.305.3
hwMplsTpCompliances	1.3.6.1.4.1.2011.5.25.305.3.1
hwMplsTpCompliance	1.3.6.1.4.1.2011.5.25.305.3.1.1			Description.
hwMplsTpGroups	1.3.6.1.4.1.2011.5.25.305.3.2
hwMplsTPGeneralGroup	1.3.6.1.4.1.2011.5.25.305.3.2.1			Indicate the atrributes of the TP tunnel.
hwMplsTPNotificationGroup	1.3.6.1.4.1.2011.5.25.305.3.2.2			Indicate the notification type.

RFC description

HUAWEI MPLS-TP MIB for managing Multiprotocol Label Switching Transport Profile tunnels and MPLS-TP network objects.

Start monitoring Huawei PTN (Packet Transport Network) / MPLS-TP capable router or switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-MPLS-TP-MIB

What Is HUAWEI-MPLS-TP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description