All MIBs › HUAWEI-MPLS-EXTEND-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2015-08-01
Category: MPLS and Traffic Engineering, Vendor: Huawei
Description: Huawei MPLS extensions MIB providing additional MPLS management objects beyond standard IETF MPLS MIBs.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-MPLS-EXTEND-MIB?
HUAWEI-MPLS-EXTEND-MIB is a Huawei vendor-specific MIB (OID 1.3.6.1.4.1.2011.5.25.121) that extends the IETF MPLS-TE-STD-MIB with Huawei-proprietary objects for managing and monitoring MPLS on Huawei routers. It defines tables such as hwMplsTunnelTable (uniquely identifying tunnels via hwMplsTunnelIndex, hwMplsTunnelInstance, and ingress/egress LSR IDs, and importing mplsTunnelAdminStatus/mplsTunnelOperStatus from MPLS-TE-STD-MIB), hwStaticLspTable/hwStaticLspTnlTable for static LSP-to-tunnel mapping, and a family of Fast Reroute tables (hwTunnelFrrBypassTable, hwTunnelFrrARHopTable, hwTunnelFrrRouteDBTable) for backup path and alternate-route information, plus traffic statistics tables for tunnels and static LSPs. This makes it a control-plane and traffic-accounting extension rather than a hardware-sensor MIB, letting an operator see tunnel administrative/operational state alongside Huawei-specific FRR bypass and traffic-volume detail that standard MPLS MIBs don't expose. It depends on the standard MPLS-TE-STD-MIB for the base tunnel objects it extends. It is deployed on Huawei MPLS-capable routers (NE/CX series running VRP) in service-provider or enterprise MPLS backbones, and engineers typically get a HUAWEI-MPLS-EXTEND-MIB download from Huawei's support site to load into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-MPLS-EXTEND-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei NE/CX series routers (MPLS-capable, Huawei VRP platform)
Monitoring Examples
An operator polls hwMplsTunnelTable for a given tunnel's mplsTunnelOperStatus and cross-references hwTunnelFrrBypassTable; an operational tunnel with no corresponding active bypass entry during a link failure would indicate FRR protection did not engage and traffic is at risk of being dropped.
What Can Be Monitored
- MPLS tunnel table entries (admin/oper status)
- static LSP and tunnel-to-static-LSP mapping table entries
- FRR bypass tunnel and backup route table entries
- per-tunnel/per-static-LSP traffic statistics counters
- TE-class and TE-VPN QoS table entries
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-MIB
| hwDatacomm | OBJECT-IDENTITY |
From IF-MIB
| ifIndex | OBJECT-TYPE |
| ifName | OBJECT-TYPE |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From MPLS-LSR-STD-MIB
| MplsIndexType |
From MPLS-TC-STD-MIB
| MplsExtendedTunnelId | |
| MplsLsrIdentifier | |
| MplsTunnelIndex | |
| MplsTunnelInstanceIndex |
From MPLS-TE-STD-MIB
| mplsTunnelAdminStatus | OBJECT-TYPE |
| mplsTunnelOperStatus | OBJECT-TYPE |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| BITS | |
| Counter32 | |
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwMplsExtendMib | 1.3.6.1.4.1.2011.5.25.121 | This MIB is used for defining the HUAWEI private extended Multiprotocol Label Switching (MPLS) MIB object. All MIB objects are used to describe private managed objects and trap definitions for MPLS. | ||
| hwMplsExtendMibTunnel | 1.3.6.1.4.1.2011.5.25.121.1 | |||
| hwMplsTunnelTable | 1.3.6.1.4.1.2011.5.25.121.1.1 | not-accessible | A tunnel needs to be uniquely identified across an MPLS network. Indexes hwMplsTunnelIndex and hwMplsTunnelInstance uniquely identify a tunnel on the LSR originating the tunnel. hwMplsTunnelIngressLSRId uniquely identifies a tunnel across an MPLS network. The last index hwMplsTunnelEgressLSRId is useful in identifying all instances of a tunnel that are terminated on the same egress LSR. The indexes of this table are hwMplsTunnelIndex, hwMplsTunnelInstance, hwMplsTunnelIngressLSRId and hwMplsTunnelEgressLSRId. | |
| hwMplsTunnelEntry | 1.3.6.1.4.1.2011.5.25.121.1.1.1 | not-accessible | A tunnel needs to be uniquely identified across an MPLS network. Indexes hwMplsTunnelIndex and hwMplsTunnelInstance uniquely identify a tunnel on the LSR originating the tunnel. hwMplsTunnelIngressLSRId uniquely identifies a tunnel across an MPLS network. The last index hwMplsTunnelEgressLSRId is useful in identifying all instances of a tunnel that are terminated on the same egress LSR. The indexes of this entry are hwMplsTunnelIndex, hwMplsTunnelInstance, hwMplsTunnelIngressLSRId and hwMplsTunnelEgressLSRId. | |
| MPL hwMplsTunnelIndex | 1.3.6.1.4.1.2011.5.25.121.1.1.1.1 | MplsTunnelIndex | not-accessible | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. When the MPLS signalling protocol is rsvp(2), this value equals to the value signaled in the Tunnel ID of the SESSION object. When the MPLS signalling protocol is crldp(3), this value equals to the value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| MPL hwMplsTunnelInstance | 1.3.6.1.4.1.2011.5.25.121.1.1.1.2 | MplsTunnelInstanceIndex | not-accessible | Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is used to identify multiple instances of tunnels for backup and parallel tunnels. When the MPLS signaling protocol is rsvp(2), this value equals to the LSP ID of the Sender Template object. When the signaling protocol is crldp(3) there is no equivalent signaling object. Reference to MPLS-TE-STD-MIB. |
| MPL hwMplsTunnelIngressLSRId | 1.3.6.1.4.1.2011.5.25.121.1.1.1.3 | MplsExtendedTunnelId | not-accessible | Indicates the ingress LSR ID of this tunnel. When the MPLS signalling protocol is rsvp(2), this value equals to the Tunnel Sender Address in the Sender Template object and may equal to the Extended Tunnel ID in the SESSION object. When the MPLS signalling protocol is crldp(3), this value equals to the Ingress LSR Router ID in the LSPID TLV object. Reference to MPLS-TE-STD-MIB. |
| MPL hwMplsTunnelEgressLSRId | 1.3.6.1.4.1.2011.5.25.121.1.1.1.4 | MplsExtendedTunnelId | not-accessible | Indicates the egress LSR ID of this tunnel. Reference to MPLS-TE-STD-MIB. |
| INT hwMplsTunnelClassType | 1.3.6.1.4.1.2011.5.25.121.1.1.1.5 | INTEGER | read-only | Indicates the bandwidth type used by this tunnel. Options: 1. bc0(1) -indicates the bandwidth type is bc0. 2. bc1(2) -indicates the bandwidth type is bc1. 3. invalidValue(3) -indicates the invalid value. |
| I32 hwMplsTunnelBandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.6 | Integer32 | read-only | Indicates the bandwidth used by this tunnel. Unit: kbit/s |
| INT hwMplsTunnelAdminStatus | 1.3.6.1.4.1.2011.5.25.121.1.1.1.7 | INTEGER | read-only | Indicates the management status of this tunnel.Reference to MPLS-TE-STD-MIB. Options: 1. up(1) -indicates the management status of this tunnel is up. 2. down(2) -indicates the management status of this tunnel is down. 3. testing(3) -indicates the tunnel is used in some test mode. |
| INT hwMplsTunnelOperStatus | 1.3.6.1.4.1.2011.5.25.121.1.1.1.8 | INTEGER | read-only | Indicates the actual operational status of this tunnel, which is but not limited to the status of this tunnel of a certain period.Reference to MPLS-TE-STD-MIB. Options: 1. up(1) -indicates that the operational status of this tunnel is up. 2. down(2) -indicates that the operational status of this tunnel is down. 3. testing(3) -indicates that the tunnel is used in some test mode. 4. unknown(4) -indicates the invalid value. 5. dormant(5) -indicates that the status cannot be determined. 6. notPresent(6) -indicates that some component is missing 7. lowerLayerDown(7) -indicates the Down state due to the state of lower layer interfaces. |
| BIT hwMplsTunnelSessionAttr | 1.3.6.1.4.1.2011.5.25.121.1.1.1.9 | Bits | read-only | Indicates protection types desired by the primary tunnel, such as node protection, link protection or bandwidth protection. Options: 1. localProtectionDesired(0) -indicates link protection. 2. nodeProtectionDesired(1) -indicates node protection. 3. bandwidthProtectionDesired(2) -indicates bandwidth protection. |
| U32 hwMplsTunnelFrrSetupPrio | 1.3.6.1.4.1.2011.5.25.121.1.1.1.10 | Unsigned32 | read-only | Indicates the setup PRI of auto-bypass tunnel. Range: 0-7 Default: 7 |
| U32 hwMplsTunnelFrrHoldingPrio | 1.3.6.1.4.1.2011.5.25.121.1.1.1.11 | Unsigned32 | read-only | Indicates the holding PRI of auto-bypass tunnel. Range: 0-7 Default: 7 |
| U32 hwMplsTunnelFrrBandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.12 | Unsigned32 | read-only | Indicates the protecting bandwidth of auto-bypass tunnel. Its value is defined by the configuration on the primary tunnel. Unit: kbit/s |
| C32 hwMplsTunnelFrrSwitchover | 1.3.6.1.4.1.2011.5.25.121.1.1.1.13 | Counter32 | read-only | Indicates FRR switching times |
| U32 hwMplsTunnelFrrBypassTableIndex | 1.3.6.1.4.1.2011.5.25.121.1.1.1.14 | Unsigned32 | read-only | Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel. The bypass table shows interfaces protected by specified bypass tunnel. |
| U32 hwMplsTunnelFrrARHopTableIndex | 1.3.6.1.4.1.2011.5.25.121.1.1.1.15 | Unsigned32 | read-only | Indicates the table index of the protection type adopted by each hop of the primary tunnel. |
| STR hwMplsTunnelName | 1.3.6.1.4.1.2011.5.25.121.1.1.1.16 | SnmpAdminString | read-only | Indicates the tunnel name. The name can refer to the tunnel on the console port of the LSR. If mplsTunnelIsIf is set to True, the IfName of the interface corresponding to this tunnel should have a value equal to hwMplsTunnelName. Reference to the description of IfName in RFC 2863. |
| U32 hwMplsTunnelIfIndex | 1.3.6.1.4.1.2011.5.25.121.1.1.1.17 | Unsigned32 | read-only | Indicates the interface index of the tunnel. It uniquely identifies the tunnel name. |
| U32 hwMplsTunnelPreBandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.18 | Unsigned32 | read-only | Indicates the original bandwidth of the tunnel when the tunnel is in the Modify state. Unit: kbit/s |
| U32 hwMplsTunnelNextBandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.19 | Unsigned32 | read-only | Indicates the bandwidth of the tunnel that is to be changed when the tunnel is in the Modify state. Unit: kbit/s |
| U32 hwMplsTunnelCt0Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.20 | Unsigned32 | read-only | The bandwidth of Class-Type 0 (CT0) in this tunnel, in kbit/s. If all CT bandwidths are 0s, it means that this tunnel's Class-Type is CT0, and bandwidth is 0 kbit/s. Unit: kbit/s |
| U32 hwMplsTunnelCt1Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.21 | Unsigned32 | read-only | The bandwidth of Class-Type 1 (CT1) in this tunnel, in kbit/s. Unit: kbit/s |
| U32 hwMplsTunnelCt2Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.22 | Unsigned32 | read-only | The bandwidth of Class-Type 2 (CT2) in this tunnel, in kbit/s. Unit: kbit/s |
| U32 hwMplsTunnelCt3Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.23 | Unsigned32 | read-only | The bandwidth of Class-Type 3 (CT3) in this tunnel, in kbit/s. Unit: kbit/s |
| U32 hwMplsTunnelCt4Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.24 | Unsigned32 | read-only | The bandwidth of Class-Type 4 (CT4) in this tunnel, in kbit/s. Unit: kbit/s |
| U32 hwMplsTunnelCt5Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.25 | Unsigned32 | read-only | The bandwidth of Class-Type 5 (CT5) in this tunnel, in kbit/s. Unit: kbit/s |
| U32 hwMplsTunnelCt6Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.26 | Unsigned32 | read-only | The bandwidth of Class-Type 6 (CT6) in this tunnel, in kbit/s. Unit: kbit/s |
| U32 hwMplsTunnelCt7Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.1.1.27 | Unsigned32 | read-only | The bandwidth of Class-Type 7 (CT7) in this tunnel, in kbit/s. Unit: kbit/s |
| INT hwMplsTunnelLspType | 1.3.6.1.4.1.2011.5.25.121.1.1.1.28 | INTEGER | read-only | This object is meaningful only at the ingress of the tunnel. It indicates LSP types. Options: 0. invalid(0) -indicates that the LSP type is invalid, the possible cause is that the LSP is not created at an ingress. 1. primary(1) -indicates the primary LSP 2. primaryModifing(2) -indicates the LSP that will replace the primary LSP 3. hotStandby(3) -indicates the hot-standby LSP 4. hotStandbyModifing(4) -indicates the LSP that will replace the hot-standby LSP 5. ordinary(5) -indicates the ordinary LSP 6. ordinaryModifing(6) -indicates the LSP that will replace the ordinary LSP 7. bestEffort(7) -indicates the Best-Effort LSP 8. bestEffortModifing(8) -indicates the LSP that will replace the Best-Effort LSP Modifying LSPs are created when users modify the make-before-break attribute of the corresponding LSP types. After being created, modifying LSPs replace the corresponding LSPs to transmit traffic. |
| STR hwMplsTunnelInterfaceName | 1.3.6.1.4.1.2011.5.25.121.1.1.1.29 | SnmpAdminString | read-only | Indicates the tunnel interface name. The object is only valid at the ingress. |
| INT hwMplsTunnelSignalProto | 1.3.6.1.4.1.2011.5.25.121.1.1.1.30 | INTEGER | read-only | Indicates the signal protocol of this tunnel |
| INT hwMplsTunnelType | 1.3.6.1.4.1.2011.5.25.121.1.1.1.31 | INTEGER | read-only | This object is meaningful only at the ingress of the tunnel. It indicates tunnel types. Options: 1. invalid(1) -indicates that the tunnel type is invalid, the possible cause is that it is not ingress node of this tunnel 2. primaryTunnel(2) -indicates that this is a primary tunnel 3. bypassTunnel(3) -indicates that this is a bypass tunnel |
| hwTunnelFrrBypassTable | 1.3.6.1.4.1.2011.5.25.121.1.2 | not-accessible | Indicates the bypass tunnel. The indexes of this table are hwTunnelFrrBypassListIndex and hwTunnelFrrBypassIndex. | |
| hwTunnelFrrBypassEntry | 1.3.6.1.4.1.2011.5.25.121.1.2.1 | not-accessible | Indicates the bypass tunnel.The indexes of this entry are hwTunnelFrrBypassListIndex and hwTunnelFrrBypassIndex. | |
| U32 hwTunnelFrrBypassListIndex | 1.3.6.1.4.1.2011.5.25.121.1.2.1.1 | Unsigned32 | not-accessible | Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel. |
| U32 hwTunnelFrrBypassIndex | 1.3.6.1.4.1.2011.5.25.121.1.2.1.2 | Unsigned32 | not-accessible | Indicates the index of the bypass tunnel interface. |
| U32 hwTunnelFrrBypassProtIfIndex | 1.3.6.1.4.1.2011.5.25.121.1.2.1.3 | Unsigned32 | read-only | Indicates the index of the interface protected by the bypass tunnel. |
| hwTunnelFrrARHopTable | 1.3.6.1.4.1.2011.5.25.121.1.3 | not-accessible | Indicates the FrrARHopTable, which will show every hop's frr protect information of the tunnel. The indexes of this table are hwTunnelFrrARHopListIndex and hwTunnelFrrARHopIndex. | |
| hwTunnelFrrARHopEntry | 1.3.6.1.4.1.2011.5.25.121.1.3.1 | not-accessible | Indicates the FrrARHopTable, which will show every hop's frr protect information of the tunnel. The indexes of this entry are hwTunnelFrrARHopListIndex and hwTunnelFrrARHopIndex. | |
| U32 hwTunnelFrrARHopListIndex | 1.3.6.1.4.1.2011.5.25.121.1.3.1.1 | Unsigned32 | not-accessible | Indicates the table index of each hop along the primary tunnel. |
| U32 hwTunnelFrrARHopIndex | 1.3.6.1.4.1.2011.5.25.121.1.3.1.2 | Unsigned32 | not-accessible | Indicates the index of each hop along the primary tunnel. |
| BIT hwTunnelFrrARHopProtDesired | 1.3.6.1.4.1.2011.5.25.121.1.3.1.3 | Bits | read-only | Indicates the FRR protection types desired by the primary tunnel interface, including: 0: link protection, 1: node protection, 2: bandwidth protection |
| BIT hwTunnelFrrARHopProtActual | 1.3.6.1.4.1.2011.5.25.121.1.3.1.4 | Bits | read-only | Indicates the actual FRR protection types of the primary tunnel interface, including: 0: link protection, 1: node protection, 2: bandwidth protection, 3: primary tunnel protection in use |
| hwTunnelFrrRouteDBTable | 1.3.6.1.4.1.2011.5.25.121.1.4 | not-accessible | Indicates the primary tunnel is protected by which bypass tunnel. The indexes of this table are hwTunnelFrrRouteDBTunnelIndex, hwTunnelFrrRouteDBTunnelInstance, hwTunnelFrrRouteDBTunnelIngressLSRId and hwTunnelFrrRouteDBTunnelEngressLSRId. | |
| hwTunnelFrrRouteDBEntry | 1.3.6.1.4.1.2011.5.25.121.1.4.1 | not-accessible | Indicates the primary tunnel is protected by which bypass tunnel. The indexes of this entry are hwTunnelFrrRouteDBTunnelIndex, hwTunnelFrrRouteDBTunnelInstance, hwTunnelFrrRouteDBTunnelIngressLSRId and hwTunnelFrrRouteDBTunnelEngressLSRId. | |
| U32 hwTunnelFrrRouteDBTunnelIndex | 1.3.6.1.4.1.2011.5.25.121.1.4.1.1 | Unsigned32 | not-accessible | Identifies the index of the primary. Manager obtains new index values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signaling protocol is rsvp(2), this value equals to the value signaled in the Tunnel ID of the SESSION object. When the MPLS signaling protocol is crldp(3), this value equals to the value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| U32 hwTunnelFrrRouteDBTunnelInstance | 1.3.6.1.4.1.2011.5.25.121.1.4.1.2 | Unsigned32 | not-accessible | Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is the object identifies multiple instances of tunnels for the purposes of backup and parallel tunnels. When the MPLS signaling protocol is rsvp(2), this value equals to the LSP ID of the Sender Template object. When the signaling protocol is crldp(3), there is no equivalent signaling object. Reference to MPLS-TE-STD-MIB. |
| U32 hwTunnelFrrRouteDBTunnelIngressLSRId | 1.3.6.1.4.1.2011.5.25.121.1.4.1.3 | Unsigned32 | not-accessible | Identifies the ingress LSR ID of the primary tunnel. When the MPLS signalling protocol is rsvp(2),LSR ID equals to the Tunnel Sender Address in the Sender Template object or the Extended Tunnel Id in the SESSION object. When the MPLS signalling protocol is crldp(3), LSR ID equals to the Ingress LSR Router ID in the LSPID TLV object. |
| U32 hwTunnelFrrRouteDBTunnelEngressLSRId | 1.3.6.1.4.1.2011.5.25.121.1.4.1.4 | Unsigned32 | not-accessible | Identifies the egress LSR ID of the primary tunnel. Reference to MPLS-TE-STD-MIB. |
| U32 hwTunnelFrrRouteDBBypassIfIndex | 1.3.6.1.4.1.2011.5.25.121.1.4.1.5 | Unsigned32 | read-only | Indicates the interface index of the bypass tunnel. |
| U32 hwTunnelFrrRouteDBInnerLabel | 1.3.6.1.4.1.2011.5.25.121.1.4.1.6 | Unsigned32 | read-only | Indicates the inner label of the primary tunnel and bypass tunnel. |
| hwStaticLspTable | 1.3.6.1.4.1.2011.5.25.121.1.5 | not-accessible | A static LSP is created by a network administrator by using static MPLS. Note that only point-to-point static LSP segments are supported. Each static MPLS LSP can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR. The indexes of this table are hwStaticLspIndex, hwStaticLspInSegmentIndex, and hwStaticLspOutSegmentIndex. | |
| hwStaticLspEntry | 1.3.6.1.4.1.2011.5.25.121.1.5.1 | not-accessible | A static LSP is created by a network administrator by using static MPLS. Note that only point-to-point static LSP segments are supported. Each static MPLS LSP can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR. The indexes of this entry are hwStaticLspIndex, hwStaticLspInSegmentIndex, and hwStaticLspOutSegmentIndex. | |
| MPL hwStaticLspIndex | 1.3.6.1.4.1.2011.5.25.121.1.5.1.1 | MplsIndexType | not-accessible | Indicates the index of the static LSP. If the string is 0x00, it means that the index is invalid. |
| MPL hwStaticLspInSegmentIndex | 1.3.6.1.4.1.2011.5.25.121.1.5.1.2 | MplsIndexType | not-accessible | Indicates the incoming label index of the static LSP/CR-LSP. If the string is 0x00, it means that the index is invalid. In this case, no corresponding mplsInSegmentEntry exists. Reference to MPLS-LSR-STD-MIB. |
| MPL hwStaticLspOutSegmentIndex | 1.3.6.1.4.1.2011.5.25.121.1.5.1.3 | MplsIndexType | not-accessible | Indicates the outgoing index of the static LSP/CR-LSP. If the entry is used to identify the incoming node or intermediate node of the LSP, this object cannot be set to the string 0x00. Because corresponding mplsOutSegmentEntry exists. If the entry is used to identify the outgoing node of the LSP, this object must be set to the string 0x00. Because no corresponding mplsOutSegmentEntry exists. Reference to MPLS-LSR-STD-MIB. |
| INT hwStaticLspOwner | 1.3.6.1.4.1.2011.5.25.121.1.5.1.4 | INTEGER | read-only | Denotes the entity that creates and manages the static LSP. See MPLS-LSR-STD-MIB. Options: 1. static(1) -indicates the static LSP. 2. crstatic(2) -indicates the static CR-LSP. 3. other(3) -indicates the LSP of another type. |
| STR hwStaticLspName | 1.3.6.1.4.1.2011.5.25.121.1.5.1.5 | SnmpAdminString | read-only | Indicates the name of the static LSP or CR-LSP. The name is appointed when the static LSP or CR-LSP is created. |
| INT hwStaticLspStatus | 1.3.6.1.4.1.2011.5.25.121.1.5.1.6 | INTEGER | read-only | Indicates the actual operation status of the static LSP/CR-LSP. Options: 1. up(1) -indicates that the static LSP/CR-LSP is in Up state. 2. down(2) -indicates that the static LSP/CR-LSP is in down state. 3. testing(3) -indicates that the static LSP/CR-LSP is used in test mode. |
| INT hwStaticLspClassType | 1.3.6.1.4.1.2011.5.25.121.1.5.1.7 | INTEGER | read-only | The Class-Type of this static lsp. Options: 1. ct0(1) -indicates that the class type is ct0. 2. ct1(2) -indicates that the class type is ct1. 3. ct2(3) -indicates that the class type is ct2. 4. ct3(4) -indicates that the class type is ct3. 5. ct4(5) -indicates that the class type is ct4. 6. ct5(6) -indicates that the class type is ct5. 7. ct6(7) -indicates that the class type is ct6. 8. ct7(8) -indicates that the class type is ct7. 9. none(9) -indicates that the class type is unconfiged. |
| U32 hwStaticLspBandwidth | 1.3.6.1.4.1.2011.5.25.121.1.5.1.8 | Unsigned32 | read-only | The bandwidth of this static lsp. Unit: kbit/s |
| hwMplsTeClassTable | 1.3.6.1.4.1.2011.5.25.121.1.6 | not-accessible | TE-class mapping is a set of a maximum of eight TE-class items. TE-class is a pair, such as TE-Class[1] = . A (setup/holding) priority associated with an LSP valid only if it appears as a pair with the Class-Type. Class-Types and priorities can be randomly paired up. You can define a maximum of eight pairs. The LSR is considered to support a particular Class-Type only if it appears in the definition of the eight possible TE-Classes. It is suggested that all the LSRs in the domain use the same TE-Class mapping. The index of this table is hwMplsTeClassId. | |
| hwMplsTeClassEntry | 1.3.6.1.4.1.2011.5.25.121.1.6.1 | not-accessible | TE-class mapping is a set of a maximum of eight TE-class items. TE-class is a pair, such as TE-Class[1] = . A (setup/holding) priority associated with an LSP valid only if it appears as a pair with the Class-Type. Class-Types and priorities can be randomly paired up. You can define a maximum of eight pairs. The LSR is considered to support a particular Class-Type only if it appears in the definition of the eight possible TE-Classes. It is suggested that all the LSRs in the domain use the same TE-Class mapping. The index of this entry is hwMplsTeClassId. | |
| U32 hwMplsTeClassId | 1.3.6.1.4.1.2011.5.25.121.1.6.1.1 | Unsigned32 | not-accessible | This value represents the index of the TE-Class configured on this LSR. |
| INT hwMplsTeClassClassType | 1.3.6.1.4.1.2011.5.25.121.1.6.1.2 | INTEGER | read-only | This value represents a Class-Type supported on the LSR. Options: 1. ct0(1) -indicates that the class type of static CR-LSP is ct0. 2. ct1(2) -indicates that the class type of static CR-LSP is ct1. 3. ct2(3) -indicates that the class type of static CR-LSP is ct2. 4. ct3(4) -indicates that the class type of static CR-LSP is ct3. 5. ct4(5) -indicates that the class type of static CR-LSP is ct4. 6. ct5(6) -indicates that the class type of static CR-LSP is ct5. 7. ct6(7) -indicates that the class type of static CR-LSP is ct6. 8. ct7(8) -indicates that the class type of static CR-LSP is ct7. |
| U32 hwMplsTeClassPriority | 1.3.6.1.4.1.2011.5.25.121.1.6.1.3 | Unsigned32 | read-only | This value represents the preemption priority (setup or holding) supported for a particular class-type, on the LSR. Range: 0-7 Default: 7 |
| OCT hwMplsTeClassDescription | 1.3.6.1.4.1.2011.5.25.121.1.6.1.4 | OCTET STRING | read-only | Textual description of the TE-Class defined by this row. |
| hwMplsIfBcTable | 1.3.6.1.4.1.2011.5.25.121.1.7 | not-accessible | This table describes bandwidth constraints associated with MPLS TE enabled interfaces. The index of this table is ifIndex. | |
| hwMplsIfBcEntry | 1.3.6.1.4.1.2011.5.25.121.1.7.1 | not-accessible | This table describes bandwidth constraints associated with MPLS TE enabled interfaces. The index of this entry is ifIndex. | |
| U32 hwMplsIfMaxResvBandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.1 | Unsigned32 | read-only | The maximum reservable bandwidth on this interface. Unit: kbit/s |
| U32 hwMplsIfBc0Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.2 | Unsigned32 | read-only | The bandwidth of Class-Type 0 (CT0) in this tunnel. Unit: kbit/s |
| U32 hwMplsIfBc1Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.3 | Unsigned32 | read-only | The bandwidth of Class-Type 1 (CT1) in this tunnel. Unit: kbit/s |
| U32 hwMplsIfBc2Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.4 | Unsigned32 | read-only | The bandwidth of Class-Type 2 (CT2) in this tunnel. Unit: kbit/s |
| U32 hwMplsIfBc3Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.5 | Unsigned32 | read-only | The bandwidth of Class-Type 3 (CT3) in this tunnel. Unit: kbit/s |
| U32 hwMplsIfBc4Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.6 | Unsigned32 | read-only | The bandwidth of Class-Type 4 (CT4) in this tunnel. Unit: kbit/s |
| U32 hwMplsIfBc5Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.7 | Unsigned32 | read-only | The bandwidth of Class-Type 5 (CT5) in this tunnel. Unit: kbit/s |
| U32 hwMplsIfBc6Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.8 | Unsigned32 | read-only | The bandwidth of Class-Type 6 (CT6) in this tunnel. Unit: kbit/s |
| U32 hwMplsIfBc7Bandwidth | 1.3.6.1.4.1.2011.5.25.121.1.7.1.9 | Unsigned32 | read-only | The bandwidth of Class-Type 7 (CT7) in this tunnel. Unit: kbit/s |
| hwStaticLspTnlTable | 1.3.6.1.4.1.2011.5.25.121.1.8 | not-accessible | hwStaticLspTnlTable is used to display static LSP token of a static LSP of a specified name. The index of this table is hwStaticLspTnlName. | |
| hwStaticLspTnlEntry | 1.3.6.1.4.1.2011.5.25.121.1.8.1 | not-accessible | hwStaticLspTnlTable is used to display static LSP token of a static LSP of a specified name. The index of this entry is hwStaticLspTnlName. | |
| STR hwStaticLspTnlName | 1.3.6.1.4.1.2011.5.25.121.1.8.1.1 | SnmpAdminString | not-accessible | Indicates the name of the Static Lsp. |
| U32 hwStaticLspTnlToken | 1.3.6.1.4.1.2011.5.25.121.1.8.1.2 | Unsigned32 | read-only | Indicates the token of the Static Lsp. |
| hwMplsTeVpnQosTable | 1.3.6.1.4.1.2011.5.25.121.1.9 | not-accessible | This table is used to display VPN QoS information of a specified TE Tunnel according to TunnelID. The index of this table is hwMplsTnlID. | |
| hwMplsTeVpnQosEntry | 1.3.6.1.4.1.2011.5.25.121.1.9.1 | not-accessible | This table is used to display VPN QoS information of a specified TE Tunnel according to TunnelID. The index of this entry is hwMplsTnlID. | |
| U32 hwMplsTnlID | 1.3.6.1.4.1.2011.5.25.121.1.9.1.1 | Unsigned32 | not-accessible | The value of this object identifies the TE tunnel ID. |
| U32 hwMplsTeVpnMaxBandwidth | 1.3.6.1.4.1.2011.5.25.121.1.9.1.2 | Unsigned32 | read-only | The value of this object identifies the bandwidth the TE tunnel can provide for VPN QoS. Unit: kbit/s |
| U32 hwMplsTeVpnAllocatedBandwidth | 1.3.6.1.4.1.2011.5.25.121.1.9.1.3 | Unsigned32 | read-only | The value of this object identifies the bandwidth used by VPN QoS, in Kbps. Unit: kbit/s |
| OCT hwStaticLspInIfIndex | 1.3.6.1.4.1.2011.5.25.121.1.11 | OCTET STRING | accessible-for-notify | Indicates the inbound interface index of a static LSP/CR-LSP. |
| OCT hwStaticLspInIfName | 1.3.6.1.4.1.2011.5.25.121.1.12 | OCTET STRING | accessible-for-notify | Indicates the name of an inbound interface of a static LSP/CR-LSP. |
| I32 hwStaticLspDownReason | 1.3.6.1.4.1.2011.5.25.121.1.13 | Integer32 | accessible-for-notify | Indicates the reason for static LSP/CR-LSP Down: 0. Other 1. Static LSP/CR-LSP up 2. MPLS disabled on an interface 3. MPLS TE disabled on an interface 4. Route change 5. Tunnel binding associated with the static LSP/CR-LSP deleted 6. Static LSP/CR-LSP configuration delete 7. Inbound interface Down 8. Outbound interface Down 9. Tunnel associated with the static LSP/CR-LSP has been shut down 10. Static LSP/CR-LSP configuration update 11. The bound ring is invalid. |
| hwMplsTunnelStatisticsTable | 1.3.6.1.4.1.2011.5.25.121.1.14 | not-accessible | A tunnel needs to be uniquely identified across an MPLS network. hwMplsTunnelStatisticsTunnelIndex uniquely identifies a tunnel on the LSR originating the tunnel. hwMplsTunnelStatisticsIngressLSRId uniquely identifies a tunnel across an MPLS network. The last index hwMplsTunnelStatisticsEgressLSRId is useful in identifying all instances of a tunnel that are terminated on the same egress LSR. The indexes of this table are hwMplsTunnelStatisticsTunnelIndex, hwMplsTunnelStatisticsIngressLSRId and hwMplsTunnelStatisticsEgressLSRId. | |
| hwMplsTunnelStatisticsEntry | 1.3.6.1.4.1.2011.5.25.121.1.14.1 | not-accessible | A tunnel needs to be uniquely identified across an MPLS network. hwMplsTunnelStatisticsTunnelIndex uniquely identifies a tunnel on the LSR originating the tunnel. hwMplsTunnelStatisticsIngressLSRId uniquely identifies a tunnel across an MPLS network. The last index hwMplsTunnelStatisticsEgressLSRId is useful in identifying all instances of a tunnel that are terminated on the same egress LSR. The indexes of this table are hwMplsTunnelStatisticsTunnelIndex, hwMplsTunnelStatisticsIngressLSRId and hwMplsTunnelStatisticsEgressLSRId. | |
| U32 hwMplsTunnelStatisticsTunnelIndex | 1.3.6.1.4.1.2011.5.25.121.1.14.1.1 | Unsigned32 | not-accessible | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. When the MPLS signalling protocol is rsvp(2), this value equals to the value signaled in the Tunnel ID of the SESSION object. When the MPLS signalling protocol is crldp(3), this value equals to the value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| IP hwMplsTunnelStatisticsIngressLSRId | 1.3.6.1.4.1.2011.5.25.121.1.14.1.2 | IpAddress | not-accessible | Indicates the ingress LSR ID of this tunnel. When the MPLS signalling protocol is rsvp(2), this value equals to the Tunnel Sender Address in the Sender Template object and may equal to the Extended Tunnel ID in the SESSION object. When the MPLS signalling protocol is crldp(3), this value equals to the Ingress LSR Router ID in the LSPID TLV object. Reference to MPLS-TE-STD-MIB. |
| IP hwMplsTunnelStatisticsEgressLSRId | 1.3.6.1.4.1.2011.5.25.121.1.14.1.3 | IpAddress | not-accessible | Indicates the egress LSR ID of this tunnel. Reference to MPLS-TE-STD-MIB. |
| C64 hwMplsTunnelStatisticsHCInOctets | 1.3.6.1.4.1.2011.5.25.121.1.14.1.4 | Counter64 | read-only | The total number of octets received on the interface, including framing characters. |
| C64 hwMplsTunnelStatisticsHCOutOctets | 1.3.6.1.4.1.2011.5.25.121.1.14.1.5 | Counter64 | read-only | The total number of octets transmitted out of the interface, including framing characters. |
| hwMplsExtendTrap | 1.3.6.1.4.1.2011.5.25.121.2 | |||
| hwLspTrap | 1.3.6.1.4.1.2011.5.25.121.2.1 | |||
| NTF hwMplsStaticLspUp | 1.3.6.1.4.1.2011.5.25.121.2.1.1 | This notification indicates that the status of referred static LSP changes to Up. | ||
| NTF hwMplsStaticLspDown | 1.3.6.1.4.1.2011.5.25.121.2.1.2 | This notification indicates that the status of referred static LSP changes to Down. | ||
| NTF hwMplsStaticCRLspUp | 1.3.6.1.4.1.2011.5.25.121.2.1.3 | This notification indicates that the status of referred static CR-LSP changes to Up. | ||
| NTF hwMplsStaticCRLspDown | 1.3.6.1.4.1.2011.5.25.121.2.1.4 | This notification indicates that the status of referred static CR-LSP changes to Down. | ||
| NTF hwMplsTeFrrProtAval | 1.3.6.1.4.1.2011.5.25.121.2.1.5 | This notification indicates that the primary tunnel is bound to bypass tunnel. | ||
| NTF hwMplsTeFrrProtNotAval | 1.3.6.1.4.1.2011.5.25.121.2.1.6 | This notification indicates that the primary tunnel is unbound to bypass tunnel. | ||
| NTF hwMplsTeFrrSwitch | 1.3.6.1.4.1.2011.5.25.121.2.1.7 | This notification indicates that the primary tunnel is switches to the bypass tunnel. | ||
| NTF hwMplsTeFrrResume | 1.3.6.1.4.1.2011.5.25.121.2.1.8 | This notification indicates that the primary tunnel is switched back from the bypass tunnel. | ||
| NTF hwMplsTunnelHSBSwitch | 1.3.6.1.4.1.2011.5.25.121.2.1.9 | This notification indicates that the data is switched from the primary CR-LSP to the HSB CR-LSP. | ||
| NTF hwMplsTunnelHSBResume | 1.3.6.1.4.1.2011.5.25.121.2.1.10 | This notification indicates that the data is switched from the HSB CR-LSP to the primary CR-LSP. | ||
| NTF hwMplsTunnelOBSwitch | 1.3.6.1.4.1.2011.5.25.121.2.1.11 | This notification indicates that the primary CR-LSP is down and the Ordinary backup CR-LSP is up. | ||
| NTF hwMplsTunnelOBResume | 1.3.6.1.4.1.2011.5.25.121.2.1.12 | This notification indicates that the data is switched from the Ordinary backup CR-LSP to the primary CR-LSP. | ||
| NTF hwMplsTunnelUp | 1.3.6.1.4.1.2011.5.25.121.2.1.13 | The hwMplsTunnelUp trap indicates that the staus of the tunnel changes into Up. | ||
| NTF hwMplsTunnelDown | 1.3.6.1.4.1.2011.5.25.121.2.1.14 | The hwMplsTunnelDown trap indicates that the staus of the tunnel changes into Down. | ||
| NTF hwMplsTunnelChangeBw | 1.3.6.1.4.1.2011.5.25.121.2.1.15 | This notification indicates that the bandwidth of the tunnel is changed. | ||
| NTF hwMplsTunnelTpOamLossSD | 1.3.6.1.4.1.2011.5.25.121.2.1.16 | This object indicates that the loss ratio of the packets carried by the tunnel exceeded the first threshold. | ||
| NTF hwMplsOamSDRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.17 | This object indicates that the loss ratio of the packets carried by the tunnel dropped below the first threshold. | ||
| NTF hwMplsOamLoss | 1.3.6.1.4.1.2011.5.25.121.2.1.18 | This object indicates that TP OAM detected tunnel connectivity faults. | ||
| NTF hwMplsOamLossRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.19 | This object indicates that TP OAM did not detect tunnel connectivity faults. | ||
| NTF hwMplsOamAis | 1.3.6.1.4.1.2011.5.25.121.2.1.20 | This object indicates that TP OAM detected an alarm indication signal. | ||
| NTF hwMplsOamAisRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.21 | This object indicates that TP OAM no longer detected alarm indication signals. | ||
| NTF hwMplsOamRdi | 1.3.6.1.4.1.2011.5.25.121.2.1.22 | This object indicates that TP OAM detected remote defects. | ||
| NTF hwMplsOamRdiRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.23 | This object indicates that the remote defects detected by TP OAM were removed. | ||
| NTF hwMplsOamMeg | 1.3.6.1.4.1.2011.5.25.121.2.1.24 | This object indicates that the names configured on the two ends of the tunnel are inconsistent. | ||
| NTF hwMplsOamMegRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.25 | This object indicates that the names configured on the two ends of the tunnel now are consistent. | ||
| NTF hwMplsOamMep | 1.3.6.1.4.1.2011.5.25.121.2.1.26 | This object indicates that the MEP-IDs configured on the two ends of the tunnel are inconsistent. | ||
| NTF hwMplsOamMepRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.27 | This object indicates that the MEP-IDs configured on the two ends of the tunnel now are consistent. | ||
| NTF hwMplsOamSF | 1.3.6.1.4.1.2011.5.25.121.2.1.28 | This object indicates that the loss ratio of the packets carried by the tunnel exceeded the second threshold in the local link. | ||
| NTF hwMplsOamSFRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.29 | This object indicates that the loss ratio of the packets carried by the tunnel dropped below the second threshold in the local link. | ||
| NTF hwMplsOamPeriod | 1.3.6.1.4.1.2011.5.25.121.2.1.30 | This object indicates that the TP OAM detection periods on the two ends of the tunnel are inconsistent. | ||
| NTF hwMplsOamPeriodRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.31 | This object indicates that the TP OAM detection periods on the two ends of the tunnel now are consistent. | ||
| NTF hwMplsOamLck | 1.3.6.1.4.1.2011.5.25.121.2.1.32 | This object indicates that TP OAM detected the service level of the tunnel has been locked. | ||
| NTF hwMplsOamLckRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.33 | This object indicates that TP OAM detected the service level of the tunnel has not been locked. | ||
| NTF hwMplsOamExcess | 1.3.6.1.4.1.2011.5.25.121.2.1.34 | This object indicates that MPLS OAM detected the tunnel received excess alarm. | ||
| NTF hwMplsOamExcessRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.35 | This object indicates that MPLS OAM detected the tunnel received excess alarm end. | ||
| NTF hwMplsOamMisMatch | 1.3.6.1.4.1.2011.5.25.121.2.1.36 | This object indicates that MPLS OAM detected the tunnel received MisMatch alarm. | ||
| NTF hwMplsOamMisMatchRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.37 | This object indicates that MPLS OAM detected the tunnel received MisMatch alarm end. | ||
| NTF hwMplsOamMisMerge | 1.3.6.1.4.1.2011.5.25.121.2.1.38 | This object indicates that MPLS OAM detected the tunnel received MisMerge alarm. | ||
| NTF hwMplsOamMisMergeRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.39 | This object indicates that MPLS OAM detected the tunnel received MisMerge alarm end. | ||
| NTF hwMplsOamUnknown | 1.3.6.1.4.1.2011.5.25.121.2.1.40 | This object indicates that MPLS OAM detected the tunnel received Unknown alarm. | ||
| NTF hwMplsOamUnknownRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.41 | This object indicates that MPLS OAM detected the tunnel received Unknown alarm end. | ||
| NTF hwMplsOamBDI | 1.3.6.1.4.1.2011.5.25.121.2.1.42 | This object indicates that MPLS OAM detected the tunnel received BDI alarm. | ||
| NTF hwMplsOamBDIRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.43 | This object indicates that MPLS OAM detected the tunnel received BDI alarm end. | ||
| NTF hwMplsOamFail | 1.3.6.1.4.1.2011.5.25.121.2.1.44 | This object indicates that MPLS OAM detected the tunnel received OAMFAIL alarm. | ||
| NTF hwMplsOamFailRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.45 | This object indicates that MPLS OAM detected the tunnel received OAMFAIL alarm end. | ||
| NTF hwMplsTunnelPrimaryUp | 1.3.6.1.4.1.2011.5.25.121.2.1.46 | This notification indicates that the status of the RSVP-TE Primary LSP changes to Up. | ||
| NTF hwMplsTunnelPrimaryDown | 1.3.6.1.4.1.2011.5.25.121.2.1.47 | This notification indicates that the status of the RSVP-TE Primary LSP changes to Down. | ||
| NTF hwMplsTunnelHotstandbyUp | 1.3.6.1.4.1.2011.5.25.121.2.1.48 | This notification indicates that the status of the RSVP-TE Hot-standby LSP changes to Up. | ||
| NTF hwMplsTunnelHotstandbyDown | 1.3.6.1.4.1.2011.5.25.121.2.1.49 | This notification indicates that the status of the RSVP-TE Hot-standby LSP changes to Down. | ||
| NTF hwMplsTunnelOrdinaryUp | 1.3.6.1.4.1.2011.5.25.121.2.1.50 | This notification indicates that the status of the RSVP-TE Ordinary LSP changes to Up. | ||
| NTF hwMplsTunnelOrdinaryDown | 1.3.6.1.4.1.2011.5.25.121.2.1.51 | This notification indicates that the status of the RSVP-TE Ordinary LSP changes to Down. | ||
| NTF hwMplsTunnelBesteffortUp | 1.3.6.1.4.1.2011.5.25.121.2.1.52 | This notification indicates that the status of the RSVP-TE Best-effort LSP changes to Up. | ||
| NTF hwMplsTunnelBesteffortDown | 1.3.6.1.4.1.2011.5.25.121.2.1.53 | This notification indicates that the status of the RSVP-TE Best-effort LSP changes to Down. | ||
| NTF hwMplsTeAutoTunnelDownClear | 1.3.6.1.4.1.2011.5.25.121.2.1.54 | This notification indicates that the TE Auto tunnel Down alarm was cleared. | ||
| NTF hwMplsTeAutoTunnelPrimaryDownClear | 1.3.6.1.4.1.2011.5.25.121.2.1.55 | This notification indicates that the Down alarm about the primary LSP in the TE Auto tunnel was cleared. | ||
| NTF hwMplsTunnelBBSwitch | 1.3.6.1.4.1.2011.5.25.121.2.1.56 | This notification indicates that the primary CR-LSP is Down and the Best-effort backup CR-LSP is Up. | ||
| NTF hwMplsTunnelBBResume | 1.3.6.1.4.1.2011.5.25.121.2.1.57 | This notification indicates that data is switched from the Best-effort backup CR-LSP to the primary CR-LSP. | ||
| NTF hwMplsExtTunnelDown | 1.3.6.1.4.1.2011.5.25.121.2.1.58 | This notification indicates that the status of te tunnel changes to Down. | ||
| NTF hwMplsExtTunnelDownClear | 1.3.6.1.4.1.2011.5.25.121.2.1.59 | This notification indicates that the down alarm of te tunnel was cleared. | ||
| NTF hwMplsOamLocalLock | 1.3.6.1.4.1.2011.5.25.121.2.1.60 | This object indicates that TP OAM detected the tunnel has been locked. | ||
| NTF hwMplsOamLocalLockRecovery | 1.3.6.1.4.1.2011.5.25.121.2.1.61 | This object indicates that TP OAM detected the tunnel has not been locked. | ||
| NTF hwMplsTunnelDelete | 1.3.6.1.4.1.2011.5.25.121.2.1.62 | This notification indicates that the mpls te tunnel was deleted. | ||
| NTF hwMplsLspThresholdExceed | 1.3.6.1.4.1.2011.5.25.121.2.1.63 | This object indicates that lsp count has exceeded the threshold. | ||
| NTF hwMplsLspThresholdExceedClear | 1.3.6.1.4.1.2011.5.25.121.2.1.64 | This object indicates that lsp count has resumed from exceeding the threshold. | ||
| NTF hwMplsLspTotalCountExceed | 1.3.6.1.4.1.2011.5.25.121.2.1.65 | This object indicates that lsp count has reached the total count. | ||
| NTF hwMplsLspTotalCountExceedClear | 1.3.6.1.4.1.2011.5.25.121.2.1.66 | This object indicates that lsp count has resumed from reaching the total count. | ||
| NTF hwMplsDynamicLabelThresholdExceed | 1.3.6.1.4.1.2011.5.25.121.2.1.67 | This object indicates that label usage has exceeded the threshold. | ||
| NTF hwMplsDynamicLabelThresholdExceedClear | 1.3.6.1.4.1.2011.5.25.121.2.1.68 | This object indicates that label usage has resumed from exceeding the threshold. | ||
| NTF hwMplsDynamicLabelTotalCountExceed | 1.3.6.1.4.1.2011.5.25.121.2.1.69 | This object indicates that label count has reached the total count. | ||
| NTF hwMplsDynamicLabelTotalCountExceedClear | 1.3.6.1.4.1.2011.5.25.121.2.1.70 | This object indicates that label usage count has resumed from reaching the total count. | ||
| NTF hwMplsResourceThresholdExceed | 1.3.6.1.4.1.2011.5.25.121.2.1.71 | This object indicates that the number of MPLS resources has exceeded the upper threshold. | ||
| NTF hwMplsResourceThresholdExceedClear | 1.3.6.1.4.1.2011.5.25.121.2.1.72 | This object indicates that the number of MPLS resources has fallen below the lower threshold. | ||
| NTF hwMplsResourceTotalCountExceed | 1.3.6.1.4.1.2011.5.25.121.2.1.73 | This object indicates that the number of MPLS resources has reached the maximum number. | ||
| NTF hwMplsResourceTotalCountExceedClear | 1.3.6.1.4.1.2011.5.25.121.2.1.74 | This object indicates that the number of MPLS resources fallen below the recovery number. | ||
| NTF hwMplsLspLoopBack | 1.3.6.1.4.1.2011.5.25.121.2.1.75 | This object indicates that the lsp was looped back. | ||
| NTF hwMplsLspLoopBackClear | 1.3.6.1.4.1.2011.5.25.121.2.1.76 | This object indicates that loopback of the LSP is restored. | ||
| NTF hwMplsTunnelCommitLost | 1.3.6.1.4.1.2011.5.25.121.2.1.77 | This object indicates that, after the device saves MPLS TE tunnel configurations, the device commits only some MPLS tunnel configurations. | ||
| NTF hwMplsTunnelCommitLostClear | 1.3.6.1.4.1.2011.5.25.121.2.1.78 | This object indicates that, after the device saves MPLS TE tunnel configurations, the device commits all MPLS tunnel configurations. | ||
| NTF hwMplsTunnelHotstandbySwitch | 1.3.6.1.4.1.2011.5.25.121.2.1.79 | This notification indicates that the data is switched from the primary CR-LSP to the HSB CR-LSP. | ||
| NTF hwMplsTunnelHotstandbyResume | 1.3.6.1.4.1.2011.5.25.121.2.1.80 | This notification indicates that the data is switched from the HSB CR-LSP to the primary CR-LSP. | ||
| hwMplsTrapObjects | 1.3.6.1.4.1.2011.5.25.121.2.2 | |||
| STR hwMplsTunnelIfName | 1.3.6.1.4.1.2011.5.25.121.2.2.1 | SnmpAdminString | accessible-for-notify | The Tunnel Interface name. |
| INT hwMplsTunnelFrrConfigOper | 1.3.6.1.4.1.2011.5.25.121.2.2.2 | INTEGER | accessible-for-notify | The value of this object identifies the operation that an FRR configuration is committed on the tunnel. Options: 1.unconfig(0) -indicates the configuration of the undo mpls te fast-reroute command is committed. 2.config(1) -indicates the configuration of the mpls te fast-reroute command is committed. 3.unknow(2) -indicates an unknown operation. |
| INT hwMplsTunnelDownReason | 1.3.6.1.4.1.2011.5.25.121.2.2.3 | INTEGER | accessible-for-notify | Indicates the alarm reason as below: 1. Other; 2. Static LSP down; 3. Static CR-LSP down; 4. The out interface of the RSVP LSP ingress is down; 5. The resource of RSVP LSP is preempted; 6. RSVP message timeout; 7. RSVP neighbor lost; 8. The bypass-tunnel is down or is unbinded with main tunnel, as bypass-tunnel is in used; 9. CSPF compute fail; 10.User shutdown the tunnel; 11.TPOAM indicates the connectivity fault of the link; 12.TPOAM indicates receive alarm indication signal defect of the link; 13.TPOAM indicates the remote defect of the link; 14.TPOAM indicates receive unexpected MEG-ID defect of the link; 15.TPOAM indicates receive unexpected MEP-ID defect of the link; 16.TPOAM indicates packet lost exceed signal fault threshold in the local link; 17.TPOAM indicates packet unexpected period defect of the link; 18.MPLS OAM connectivity fault; 19.MPLS OAM TTSI excess; 20.MPLS OAM TTSI mismatch; 21.MPLS OAM TTSI merge error; 22.MPLS OAM unknown error; 23.MPLS OAM BDI; 24.MPLS OAM FDI; 25.MPLS OAM signal fail; 26.MPLS OAM signal degrade; 27.MPLS OAM fail; 28.Service resume; 29.Service delete; 100. Clear. |
| INT hwMplsLspProtocol | 1.3.6.1.4.1.2011.5.25.121.2.2.4 | INTEGER | accessible-for-notify | The value of this object identifies the protocol of the lsp which exceeds the threshold or total count. Options: 1.ldp(1) -indicates the lsp is ldp lsp. 2.bgp(2) -indicates the lsp is bgp lsp. 3.bgpv6(3) -indicates the lsp is bgpv6 lsp. 4.ldpfrr(4) -indicates the lsp is ldp frr lsp. 5.rsvp(5) -indicates the lsp is rsvp te lsp. 6.totalLsp(6) -indicates the lsp is total lsp. 7.totalCrLsp(7) -indicates the lsp is total cr-lsp. 8.ldpIngress(8) -indicates the lsp is ldp ingress lsp. 9.ldpTransit(9) -indicates the lsp is ldp transit lsp. 10.ldpEgress(10) -indicates the lsp is ldp egress lsp. 11.bgpIngress(11) -indicates the lsp is bgp ingress lsp. 12.bgpEgress(12) -indicates the lsp is bgp egress lsp. 13.bgpv6Ingress(13) -indicates the lsp is bgpv6 ingress lsp. 14.bgpv6Egress(14) -indicates the lsp is bgpv6 egress lsp. 15.rsvpIngress(15) -indicates the lsp is rsvp te ingress lsp. 16.rsvpTransit(16) -indicates the lsp is rsvp te transit lsp. 17.rsvpEgress(17) -indicates the lsp is rsvp te egress lsp. 18.totalLspIngress(18) -indicates the lsp is total ingress lsp. 19.totalLspTransit(19) -indicates the lsp is total transit lsp. 20.totalLspEgress(20) -indicates the lsp is total egress lsp. 21.totalCrLspIngress(21) -indicates the lsp is total ingress cr-lsp. 22.totalCrLspTransit(22) -indicates the lsp is total transit cr-lsp. 23.totalCrLspEgress(23) -indicates the lsp is total egress cr-lsp. 24.totalPublicNetLspIngressTransit(24) -indicates the lsp is total ingress and transit public netwrok lsp. 25.totalPublicNetLspTransitEgress(25) -indicates the lsp is total transit and egress public network cr-lsp. 26.privateNetBgp(26) -indicates the lsp is private network bgp lsp. 27.unknown(100) -indicates the lsp type is unknown. |
| I32 hwMplsLspThreshold | 1.3.6.1.4.1.2011.5.25.121.2.2.5 | Integer32 | accessible-for-notify | The value of this object identifies the threshold of the lsp. |
| I32 hwMplsLspTotalCount | 1.3.6.1.4.1.2011.5.25.121.2.2.6 | Integer32 | accessible-for-notify | The value of this object identifies the total permit count of lsp. |
| I32 hwMplsLspCurrentCount | 1.3.6.1.4.1.2011.5.25.121.2.2.7 | Integer32 | accessible-for-notify | The value of this object identifies the current count of the lsp. |
| OID hwMplsTunnelDownLSRID | 1.3.6.1.4.1.2011.5.25.121.2.2.8 | MplsLsrIdentifier | accessible-for-notify | The value of this object identifies the LSR ID of the error node on a tunnel. |
| IP hwMplsTunnelDownIfIpAddr | 1.3.6.1.4.1.2011.5.25.121.2.2.9 | InetAddress | accessible-for-notify | The value of this object identifies the IP address of the error interface on a tunnel. |
| IPt hwMplsTunnelDownIfIpAddrType | 1.3.6.1.4.1.2011.5.25.121.2.2.10 | InetAddressType | accessible-for-notify | The value of this object identifies the IP address type of the error interface on a tunnel. |
| INT hwMplsResourceType | 1.3.6.1.4.1.2011.5.25.121.2.2.11 | INTEGER | accessible-for-notify | The value of this object identifies that the number of MPLS resources has exceeded the threshold or the maximum number. Options: 1.autoBypassTunnelIf(1) -Indicates that the resource is auto bypass tunnel interface. 2.p2mpAutoTunnelIf(2) -Indicates that the resource is P2MP auto tunnel interface. 3.teBfd(3) -Indicates that the resource is dynamic BFD for TE LSP. 4.ldpBfd(4) -Indicates that the resource is dynamic BFD for LDP LSP. 5.mldpTotalTree(5) -Indicates that the resource is the total number of MLDP trees. 6.mldpTotalBranch(6) -Indicates that the resource is the total number of MLDP branches. 7.ldpTotalRemoteAdjacency(7) -Indicates that the resource is LDP total remote adjacency. 8.outSegment(8) -Indicates that the resource is LDP outSegment. 9.autoPrimaryTunnelIf(9) -Indicates that the resource is auto primary tunnel interface. 10.ldpTotalLocalAdjacency(10) -Indicates that the resource is LDP total local adjacency. 11.cspfNode(11) -Indicates that the resource is cspf node. 12.cspfLink(12) -Indicates that the resource is cspf link. 13.cspfNlsa(13) -Indicates that the resource is cspf nlsa. 14.cspfSrlg(14) -Indicates that the resource is cspf srlg. 15.unknown(100) -Indicates that the resource type is unknown. |
| I32 hwMplsResourceCurrentCount | 1.3.6.1.4.1.2011.5.25.121.2.2.12 | Integer32 | accessible-for-notify | The value of this object identifies the number of the resources. |
| I32 hwMplsResourceThreshold | 1.3.6.1.4.1.2011.5.25.121.2.2.13 | Integer32 | accessible-for-notify | The value of this object identifies the threshold for the number of the resources. |
| I32 hwMplsResourceTotalCount | 1.3.6.1.4.1.2011.5.25.121.2.2.14 | Integer32 | accessible-for-notify | The value of this object identifies the maximum number of allowed resources. |
| I32 hwMplsSessionTunnelId | 1.3.6.1.4.1.2011.5.25.121.2.2.15 | Integer32 | accessible-for-notify | The value of this object identifies the Tunnel ID. |
| I32 hwMplsLocalLspId | 1.3.6.1.4.1.2011.5.25.121.2.2.16 | Integer32 | accessible-for-notify | The value of this object identifies the LSP ID. |
| OID hwMplsIngressLsrId | 1.3.6.1.4.1.2011.5.25.121.2.2.17 | MplsLsrIdentifier | accessible-for-notify | The value of this object identifies the ingress LSR ID. |
| OID hwMplsEgressLsrId | 1.3.6.1.4.1.2011.5.25.121.2.2.18 | MplsLsrIdentifier | accessible-for-notify | The value of this object identifies the egress LSR ID. |
| STR hwMplsLspName | 1.3.6.1.4.1.2011.5.25.121.2.2.19 | SnmpAdminString | accessible-for-notify | This object indicates the name of an bidirectional static CR-LSP. |
| NTF hwMplsTunnelFrrConfigChange | 1.3.6.1.4.1.2011.5.25.121.2.3 | When the trap indicating that TE-Frr configuration of Tunnel is changed is sent, the cause for the change of TE-FRR configuration of Tunnel is displayed. | ||
| hwMplsGlobalObject | 1.3.6.1.4.1.2011.5.25.121.3 | |||
| INT hwMplsGlobalWorkMode | 1.3.6.1.4.1.2011.5.25.121.3.1 | INTEGER | read-only | The work mode of DS-TE system, default mode is nonstandard. Options: 1. standard(1) -indicates work mode of DS-TE system is standard 2. nonstandard(2) -indicates work mode of DS-TE system is nonstandard |
| INT hwMplsGlobalBcModel | 1.3.6.1.4.1.2011.5.25.121.3.2 | INTEGER | read-only | Bandwidth Constraint Model currently used by this LSR. Options: 1. rdm(1) -indicates that the bandwidth constraint model is RDM. 2. mam(2) -indicates that the bandwidth constraint model is MAM. 3. extendMam(3) -indicates that the bandwidth constraint model is ExtendMam. |
| U32 hwMplsDynamicLabelTotalCount | 1.3.6.1.4.1.2011.5.25.121.3.3 | Unsigned32 | read-only | The value of this object identifies the total permit count of dynamic label. |
| U32 hwMplsDynamicLabelCurrentCount | 1.3.6.1.4.1.2011.5.25.121.3.4 | Unsigned32 | read-only | The value of this object identifies the current count of the dynamic label. |
| U32 hwMplsDynamicLabelThresholdUpperLimit | 1.3.6.1.4.1.2011.5.25.121.3.5 | Unsigned32 | read-only | The upper limit threshold value (%) of dynamic label, default value is 80. |
| U32 hwMplsDynamicLabelThresholdLowerLimit | 1.3.6.1.4.1.2011.5.25.121.3.6 | Unsigned32 | read-only | The lower limit threshold value (%) of dynamic label, default value is 70. |
| hwMplsLspStatistics | 1.3.6.1.4.1.2011.5.25.121.4 | |||
| hwMplsLspStatisticsTable | 1.3.6.1.4.1.2011.5.25.121.4.1 | not-accessible | hwMplsLspStatisticsTable is used to display the number of ingress LSPs, transit LSPs, or egress LSPs of specified types. The index of this table is hwMplsLspStatisticsLspType. | |
| hwMplsLspStatisticsEntry | 1.3.6.1.4.1.2011.5.25.121.4.1.1 | not-accessible | hwMplsLspStatisticsTable is used to display the number of ingress LSPs, transit LSPs, or egress LSPs of specified types. The index of this entry is hwMplsLspStatisticsLspType. | |
| INT hwMplsLspStatisticsLspType | 1.3.6.1.4.1.2011.5.25.121.4.1.1.1 | INTEGER | not-accessible | This object indicates the LSP type. Options: 1. staticLsp(1) -indicates the static LSP. 2. staticCrLsp(2) -indicates the static CR-LSP. 3. ldpLsp(3) -indicates the LDP LSP. 4. rsvpCrLsp(4) -indicates the RSVP LSP. 5. bgpLsp(5) -indicates the BGP LSP. 6. asbrLsp(6) -indicates the ASBR LSP. 7. bgpIpv6Lsp(7) -indicates the BGP IPv6 LSP. 8. l3vpnIpv6Lsp(8)-indicates the L3VPN IPv6 LSP. |
| U32 hwMplsLspStatisticsIngressLspCount | 1.3.6.1.4.1.2011.5.25.121.4.1.1.2 | Unsigned32 | read-only | This object indicates the number of ingress LSPs of a specified type. |
| U32 hwMplsLspStatisticsTransitLspCount | 1.3.6.1.4.1.2011.5.25.121.4.1.1.3 | Unsigned32 | read-only | This object indicates the number of transit LSPs of a specified type. |
| U32 hwMplsLspStatisticsEgressLspCount | 1.3.6.1.4.1.2011.5.25.121.4.1.1.4 | Unsigned32 | read-only | This object indicates the number of egress LSPs of a specified type. |
| U32 hwMplsLspStatisticsTotalLspCount | 1.3.6.1.4.1.2011.5.25.121.4.1.1.5 | Unsigned32 | read-only | This object indicates the total number of the ingress LSPs, transit LSPs and egress LSP of specified types. |
| hwMplsTrafficStatisticsStaticLspTable | 1.3.6.1.4.1.2011.5.25.121.4.2 | not-accessible | Indicates the traffic statistics of a LSP. The indexes of this table is hwMplsTrafficStatisticsStaticLspName. | |
| hwMplsTrafficStatisticsStaticLspEntry | 1.3.6.1.4.1.2011.5.25.121.4.2.1 | not-accessible | Indicates the traffic statistics of a LSP. The indexes of this entry is hwMplsTrafficStatisticsStaticLspName. | |
| STR hwMplsTrafficStatisticsStaticLspName | 1.3.6.1.4.1.2011.5.25.121.4.2.1.1 | SnmpAdminString | not-accessible | Indicates the name of the static LSP or CR-LSP. The name is appointed when the static LSP or CR-LSP is created. |
| C64 hwMplsTrafficStatisticsStaticLspForwardInBytes | 1.3.6.1.4.1.2011.5.25.121.4.2.1.2 | Counter64 | read-only | An estimate of the forward of bistatic LSP's current incoming traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: bytes |
| C64 hwMplsTrafficStatisticsStaticLspForwardInPackets | 1.3.6.1.4.1.2011.5.25.121.4.2.1.3 | Counter64 | read-only | An estimate of the forward of bistatic LSP's current incoming traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: packets |
| C64 hwMplsTrafficStatisticsStaticLspForwardOutBytes | 1.3.6.1.4.1.2011.5.25.121.4.2.1.4 | Counter64 | read-only | An estimate of the forward of bistatic LSP's current outgoing traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: bytes |
| C64 hwMplsTrafficStatisticsStaticLspForwardOutPackets | 1.3.6.1.4.1.2011.5.25.121.4.2.1.5 | Counter64 | read-only | An estimate of the forward of bistatic LSP's current outgoing traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: packets |
| C64 hwMplsTrafficStatisticsStaticLspBackwardInBytes | 1.3.6.1.4.1.2011.5.25.121.4.2.1.6 | Counter64 | read-only | An estimate of the backward of bistatic LSP's current incoming traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: bytes |
| C64 hwMplsTrafficStatisticsStaticLspBackwardInPackets | 1.3.6.1.4.1.2011.5.25.121.4.2.1.7 | Counter64 | read-only | An estimate of the backward of bistatic LSP's current incoming traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: packets |
| C64 hwMplsTrafficStatisticsStaticLspBackwardOutBytes | 1.3.6.1.4.1.2011.5.25.121.4.2.1.8 | Counter64 | read-only | An estimate of the backward of bistatic LSP's current outgoing traffic statistics in units of bytes. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: bytes |
| C64 hwMplsTrafficStatisticsStaticLspBackwardOutPackets | 1.3.6.1.4.1.2011.5.25.121.4.2.1.9 | Counter64 | read-only | An estimate of the backward of bistatic LSP's current outgoing traffic statistics in units of packets. For a sub-layer which has no concept of traffic statistics, this object should be zero. Unit: packets |
| hwMplsExtendConformance | 1.3.6.1.4.1.2011.5.25.121.6 | |||
| hwMplsExtendGroups | 1.3.6.1.4.1.2011.5.25.121.6.1 | |||
| hwMplsTunnelGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.1 | Indicate the atrributes of the tunnel. | ||
| hwStaticLspGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.2 | Indicate the atrributes of the static lsp. | ||
| hwMplsDsTeGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.3 | Indicate the atrributes about DS-TE. | ||
| hwMplsLspStatisticsGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.4 | Indicate LSP statistics. | ||
| hwMplsObsoleteGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.5 | Indicate the OBSOLETE objects of MPLS. | ||
| hwMplsTrapGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.6 | For mpls trap object. | ||
| hwMplsRingGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.7 | For mpls ring trap object. | ||
| hwMplsGlobalGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.8 | For mpls global object. | ||
| hwMplsLspGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.9 | For mpls lsp object. | ||
| hwMplsLspTrafficStatisticGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.10 | Indicate the traffic statistic of the LSP. | ||
| hwMplsResourceGroup | 1.3.6.1.4.1.2011.5.25.121.6.1.11 | For mpls resource object. | ||
| hwMplsExtendCompliances | 1.3.6.1.4.1.2011.5.25.121.6.2 | |||
| hwExtendTrapGroup | 1.3.6.1.4.1.2011.5.25.121.6.2.1 | Indicate the traps. | ||
| hwObsoleteTrapGroup | 1.3.6.1.4.1.2011.5.25.121.6.2.2 | Indicate the Obsolete traps. | ||
| hwMplsModuleCompliance | 1.3.6.1.4.1.2011.5.25.121.6.2.3 | hwMplsModuleCompliance | ||
| hwMplsRingMib | 1.3.6.1.4.1.2011.5.25.121.7 | |||
| hwMplsRingTable | 1.3.6.1.4.1.2011.5.25.121.7.1 | not-accessible | Indicates the table information of the MPLS ring. | |
| hwMplsRingEntry | 1.3.6.1.4.1.2011.5.25.121.7.1.1 | not-accessible | Indicates the table information of the MPLS ring. | |
| U32 hwMplsRingID | 1.3.6.1.4.1.2011.5.25.121.7.1.1.1 | Unsigned32 | not-accessible | Indicates the ID of the MPLS ring. |
| U32 hwMplsRingNodeID | 1.3.6.1.4.1.2011.5.25.121.7.1.1.2 | Unsigned32 | read-only | Indicates the ID of the current Node on the MPLS ring. |
| OCT hwMplsRingName | 1.3.6.1.4.1.2011.5.25.121.7.1.1.3 | OCTET STRING | read-only | Indicates the name of MPLS ring. |
| OCT hwMplsRingDirection | 1.3.6.1.4.1.2011.5.25.121.7.1.1.4 | OCTET STRING | read-only | Indicates the direction of the MPLS ring. |
| OCT hwMplsRingSwitchReason | 1.3.6.1.4.1.2011.5.25.121.7.1.1.5 | OCTET STRING | read-only | Indicates the switch reason of the MPLS ring. |
| hwMplsRingTrap | 1.3.6.1.4.1.2011.5.25.121.7.2 | |||
| NTF hwMplsRingSwitch | 1.3.6.1.4.1.2011.5.25.121.7.2.1 | The notification indicates that the MPLS ring switched. | ||
| NTF hwMplsRingResume | 1.3.6.1.4.1.2011.5.25.121.7.2.2 | The notification indicates that the MPLS ring resumed. | ||
| NTF hwMplsRingWestOamLoss | 1.3.6.1.4.1.2011.5.25.121.7.2.3 | The notification indicates that no expected CV/FFD packet is received for three consecutive cycles in the west of the MPLS ring. | ||
| NTF hwMplsRingWestOamLossClear | 1.3.6.1.4.1.2011.5.25.121.7.2.4 | The notification indicates that the hwMplsRingWestOamLoss alarm was cleared. | ||
| NTF hwMplsRingEastOamLoss | 1.3.6.1.4.1.2011.5.25.121.7.2.5 | The notification indicates that no expected CV/FFD packet is received for three consecutive cycles in the east of the MPLS ring. | ||
| NTF hwMplsRingEastOamLossClear | 1.3.6.1.4.1.2011.5.25.121.7.2.6 | The notification indicates that the hwMplsRingEastOamLoss alarm was cleared. | ||
| NTF hwMplsRingWestOamRDI | 1.3.6.1.4.1.2011.5.25.121.7.2.7 | The notification indicates that RDI packets are received in the west of the MPLS ring, indicating that a fault occurs on the forward ring. | ||
| NTF hwMplsRingWestOamRDIClear | 1.3.6.1.4.1.2011.5.25.121.7.2.8 | The notification indicates that the hwMplsRingWestOamRDI alarm was cleared. | ||
| NTF hwMplsRingEastOamRDI | 1.3.6.1.4.1.2011.5.25.121.7.2.9 | The notification indicates that RDI packets are received in the east of the MPLS ring, indicating that a fault occurs on the forward ring. | ||
| NTF hwMplsRingEastOamRDIClear | 1.3.6.1.4.1.2011.5.25.121.7.2.10 | The notification indicates that the hwMplsRingEastOamRDI alarm was cleared. | ||
| NTF hwMplsRingWestOamUnexpectedMEG | 1.3.6.1.4.1.2011.5.25.121.7.2.11 | The notification indicates that a CCM frame carrying a correct MEG level but incorrect MEG ID is received in the west of the MPLS ring. | ||
| NTF hwMplsRingWestOamUnexpectedMEGClear | 1.3.6.1.4.1.2011.5.25.121.7.2.12 | The notification indicates that the hwMplsRingWestOamUnexpectedMEG alarm was cleared. | ||
| NTF hwMplsRingEastOamUnexpectedMEG | 1.3.6.1.4.1.2011.5.25.121.7.2.13 | The notification indicates that a CCM frame carrying a correct MEG level but incorrect MEG ID is received in the east of the MPLS ring. | ||
| NTF hwMplsRingEastOamUnexpectedMEGClear | 1.3.6.1.4.1.2011.5.25.121.7.2.14 | The notification indicates that the hwMplsRingEastOamUnexpectedMEG alarm was cleared. | ||
| NTF hwMplsRingWestOamUnexpectedPeriod | 1.3.6.1.4.1.2011.5.25.121.7.2.15 | The notification indicates that a CCM frame carrying a correct MEG level, MEG ID, and MEP ID but incorrect period value is received in the west MEP of the MPLS ring. | ||
| NTF hwMplsRingWestOamUnexpectedPeriodClear | 1.3.6.1.4.1.2011.5.25.121.7.2.16 | The notification indicates that the hwMplsRingWestOamUnexpectedPeriod alarm was cleared. | ||
| NTF hwMplsRingEastOamUnexpectedPeriod | 1.3.6.1.4.1.2011.5.25.121.7.2.17 | The notification indicates that a CCM frame carrying a correct MEG level, MEG ID, and MEP ID but incorrect period value is received in the east MEP of the MPLS ring. | ||
| NTF hwMplsRingEastOamUnexpectedPeriodClear | 1.3.6.1.4.1.2011.5.25.121.7.2.18 | The notification indicates that the hwMplsRingEastOamUnexpectedPeriod alarm was cleared. | ||
| NTF hwMplsRingWestOamExcess | 1.3.6.1.4.1.2011.5.25.121.7.2.19 | The notification indicates that five or more CV/FFD packets are correctly received within three consecutive cycles in the west of the MPLS ring. | ||
| NTF hwMplsRingWestOamExcessClear | 1.3.6.1.4.1.2011.5.25.121.7.2.20 | The notification indicates that the hwMplsRingWestOamExcess alarm was cleared. | ||
| NTF hwMplsRingEastOamExcess | 1.3.6.1.4.1.2011.5.25.121.7.2.21 | The notification indicates that five or more CV/FFD packets are correctly received within three consecutive cycles in the east of the MPLS ring. | ||
| NTF hwMplsRingEastOamExcessClear | 1.3.6.1.4.1.2011.5.25.121.7.2.22 | The notification indicates that the hwMplsRingEastOamExcess alarm was cleared. | ||
| NTF hwMplsRingWestOamSD | 1.3.6.1.4.1.2011.5.25.121.7.2.23 | The notification indicates that the number of packets for connectivity check received in the west of the MPLS ring is smaller than the SD threshold. | ||
| NTF hwMplsRingWestOamSDClear | 1.3.6.1.4.1.2011.5.25.121.7.2.24 | The notification indicates that the hwMplsRingWestOamSD alarm was cleared. | ||
| NTF hwMplsRingEastOamSD | 1.3.6.1.4.1.2011.5.25.121.7.2.25 | The notification indicates that the number of packets for connectivity check received in the east of the MPLS ring is smaller than the SD threshold. | ||
| NTF hwMplsRingEastOamSDClear | 1.3.6.1.4.1.2011.5.25.121.7.2.26 | The notification indicates that the hwMplsRingEastOamSD alarm was cleared. | ||
| NTF hwMplsRingWestOamSF | 1.3.6.1.4.1.2011.5.25.121.7.2.27 | The notification indicates that the number of packets for connectivity check received in the west of the MPLS ring is smaller than the SF threshold. | ||
| NTF hwMplsRingWestOamSFClear | 1.3.6.1.4.1.2011.5.25.121.7.2.28 | The notification indicates that the hwMplsRingWestOamSF alarm was cleared. | ||
| NTF hwMplsRingEastOamSF | 1.3.6.1.4.1.2011.5.25.121.7.2.29 | The notification indicates that the number of packets for connectivity check received in the east of the MPLS ring is smaller than the SF threshold. | ||
| NTF hwMplsRingEastOamSFClear | 1.3.6.1.4.1.2011.5.25.121.7.2.30 | The notification indicates that the hwMplsRingEastOamSF alarm was cleared. | ||
| NTF hwMplsRingWestAPSSwitch | 1.3.6.1.4.1.2011.5.25.121.7.2.31 | The notification indicates that APS switching occurs in the west of the MPLS ring. | ||
| NTF hwMplsRingWestAPSResume | 1.3.6.1.4.1.2011.5.25.121.7.2.32 | The notification indicates that APS switches back in the west of the MPLS ring. | ||
| NTF hwMplsRingEastAPSSwitch | 1.3.6.1.4.1.2011.5.25.121.7.2.33 | The notification indicates that APS switching occurs in the east of the MPLS ring. | ||
| NTF hwMplsRingEastAPSResume | 1.3.6.1.4.1.2011.5.25.121.7.2.34 | The notification indicates that APS switches back in the east of the MPLS ring. | ||
| NTF hwMplsRingWestAPSSwitchFail | 1.3.6.1.4.1.2011.5.25.121.7.2.35 | The notification indicates that the remote APS switching fails in the west of the MPLS ring. | ||
| NTF hwMplsRingWestAPSSwitchFailClear | 1.3.6.1.4.1.2011.5.25.121.7.2.36 | The notification indicates that the hwMplsRingWestAPSSwitchFail alarm was cleared. | ||
| NTF hwMplsRingEastAPSSwitchFail | 1.3.6.1.4.1.2011.5.25.121.7.2.37 | The notification indicates that the remote APS switching fails in the east of the MPLS ring. | ||
| NTF hwMplsRingEastAPSSwitchFailClear | 1.3.6.1.4.1.2011.5.25.121.7.2.38 | The notification indicates that the hwMplsRingEastAPSSwitchFail alarm was cleared. | ||
| NTF hwMplsRingWestAPSLost | 1.3.6.1.4.1.2011.5.25.121.7.2.39 | The notification indicates that APS packets are missing in the west of the MPLS ring. | ||
| NTF hwMplsRingWestAPSLostClear | 1.3.6.1.4.1.2011.5.25.121.7.2.40 | The notification indicates that the hwMplsRingWestAPSLost alarm was cleared. | ||
| NTF hwMplsRingEastAPSLost | 1.3.6.1.4.1.2011.5.25.121.7.2.41 | The notification indicates that APS packets are missing in the east of the MPLS ring. | ||
| NTF hwMplsRingEastAPSLostClear | 1.3.6.1.4.1.2011.5.25.121.7.2.42 | The notification indicates that the hwMplsRingEastAPSLost alarm was cleared. | ||
| NTF hwMplsRingWestAPSMismatch | 1.3.6.1.4.1.2011.5.25.121.7.2.43 | The notification indicates that the source ID carried by APS packets received in the west is different from the peer source ID configured for the west state machine on the MPLS ring. | ||
| NTF hwMplsRingWestAPSMismatchClear | 1.3.6.1.4.1.2011.5.25.121.7.2.44 | The notification indicates that the hwMplsRingWestAPSMismatch alarm was cleared. | ||
| NTF hwMplsRingEastAPSMismatch | 1.3.6.1.4.1.2011.5.25.121.7.2.45 | The notification indicates that the source ID carried by APS packets received in the east is different from the peer source ID configured for the east state machine on the MPLS ring. | ||
| NTF hwMplsRingEastAPSMismatchClear | 1.3.6.1.4.1.2011.5.25.121.7.2.46 | The notification indicates that the hwMplsRingEastAPSMismatch alarm was cleared. | ||
| NTF hwMplsRingWestOamUnexpectedMEP | 1.3.6.1.4.1.2011.5.25.121.7.2.47 | The notification indicates that a CCM frame carrying a correct MEG level and correct MEG ID but not the expected MEP ID is received in the west of the MPLS ring. | ||
| NTF hwMplsRingWestOamUnexpectedMEPClear | 1.3.6.1.4.1.2011.5.25.121.7.2.48 | The notification indicates that the hwMplsRingWestOamUnexpectedMEP alarm was cleared. | ||
| NTF hwMplsRingEastOamUnexpectedMEP | 1.3.6.1.4.1.2011.5.25.121.7.2.49 | The notification indicates that a CCM frame carrying a correct MEG level and correct MEG ID but not the expected MEP ID is received in the east of the MPLS ring. | ||
| NTF hwMplsRingEastOamUnexpectedMEPClear | 1.3.6.1.4.1.2011.5.25.121.7.2.50 | The notification indicates that the hwMplsRingEastOamUnexpectedMEP alarm was cleared. |
RFC description
Huawei MPLS multiprotocol label switching tunnel management and traffic engineering.
Start monitoring Huawei NE/CX series router (MPLS-capable, VRP platform, FRR/tunnel extensions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.