HUAWEI-PW-CMD-MIB

All MIBs › HUAWEI-PW-CMD-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2012-01-10

Category: MPLS and Traffic Engineering, Pseudowire, Vendor: Huawei

Description: Huawei pseudowire command MIB for configuring and monitoring pseudowire services including Ethernet and ATM emulation.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-PW-CMD-MIB?

HUAWEI-PW-CMD-MIB (module identity hwPwCmdMIB, under hwMpls) is a Huawei vendor-specific MIB implementing Pseudo Wire Emulation Edge-to-Edge (PWE3) configuration and monitoring, extending the standards-based PW-STD-MIB with Huawei-specific command/status objects for Ethernet and ATM emulation over MPLS. Its core hwPwCmdVcTable models each pseudowire's signaling protocol (hwPwCmdVcSignalProtocol: ldp/static/udp), peer address, inbound/outbound MPLS labels, live status (hwPwCmdVcStatus: down/up/plugout, an instance of VcStatusType), and 1:1/1+1 protection-switching peer objects (hwPwCmdVcSwitchSignalProtocol, hwPwCmdVcSwitchPeerAddr) for redundant PW pairs, complemented by notifications for working/protect switchovers (hwPwCmdVcSwitchWtoP/PtoW) and VC up/down transitions (hwPwCmdVcUp/hwPwCmdVcDown). This makes it useful for monitoring MPLS L2VPN pseudowire service health — confirming a PW's operational state, detecting unplanned working/protect switchovers, and tracking VCCV connectivity-verification and CAR traffic-policing sub-objects referenced elsewhere in the module — on carrier or enterprise MPLS networks offering Ethernet/ATM private-line emulation. It depends on PW-STD-MIB (RFC 5601) for shared indices (pwIndex, pwType, pwID) and on HUAWEI-MIB/HUAWEI-PW-TC-MIB for vendor conventions, and engineers troubleshooting Huawei PWE3 deployments frequently reference the HUAWEI-PW-CMD-MIB MIB for these VC status objects.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-PW-CMD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei MPLS-capable routers/switches supporting PWE3 pseudowire services

Monitoring Examples

An operator polls hwPwCmdVcTable for hwPwCmdVcStatus on a given hwPwCmdVcIndex and subscribes to hwPwCmdVcSwitchWtoP notifications; a VC status showing down(1) alongside a recent working-to-protect switchover notification would indicate the primary pseudowire path failed and traffic is now riding the protect path.

What Can Be Monitored

pseudowire operational status (up/down/plugout)
PW inbound/outbound MPLS label assignment
1:1/1+1 protection switchover notifications
PW signaling protocol configuration (LDP/static/UDP)
PW CAR (traffic policing) parameters
VCCV connectivity-verification configuration

Imported Objects

From HUAWEI-MIB

hwMpls

OBJECT-IDENTITY

From HUAWEI-PW-TC-MIB

PwVcType

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddressType

From PW-STD-MIB

pwID	OBJECT-TYPE
pwIndex	OBJECT-TYPE
pwPeerAddr	OBJECT-TYPE
pwPeerAddrType	OBJECT-TYPE
pwType	OBJECT-TYPE

From SNMPv2-CONF

NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwPw	1.3.6.1.4.1.2011.5.12.8
hwPwCmdMIB	1.3.6.1.4.1.2011.5.12.8.1			Pseudo Wire Emulation Edge-to-Edge (PWE3) is an end-to-end L2 service bearing technology, that belongs to L2 VPN in the P2P mode. The system implements the PWE3 architecture through MPLS, by using the LDP or RSVP-TE protocol as signaling. Therefore, it can implement the ATM and Ethernet emulation services and establish the ATM or Ethernet private lines. Thus, it provides a solution to the emulation private line service in the IP network.
hwPwCmdVcNotifications	1.3.6.1.4.1.2011.5.12.8.1.1
NTF hwPwCmdVcSwitchWtoP	1.3.6.1.4.1.2011.5.12.8.1.1.1			This notification is generated when switch from working pw to protect pw happens.
NTF hwPwCmdVcSwitchPtoW	1.3.6.1.4.1.2011.5.12.8.1.1.2			This notification is generated when switch from protect pw to working pw happens.
NTF hwPwCmdVcUp	1.3.6.1.4.1.2011.5.12.8.1.1.3			This notification is generated when the vc status change from other status to up.
NTF hwPwCmdVcDown	1.3.6.1.4.1.2011.5.12.8.1.1.4			This notification is generated when the vc status change from other status to down.
hwPwCmdObjects	1.3.6.1.4.1.2011.5.12.8.1.2
U32 hwPwCmdVcIndexNext	1.3.6.1.4.1.2011.5.12.8.1.2.1	Unsigned32	read-only	This object contains an appropriate value to be used for hwPwCmdVcIndex when creating entries in the hwPwCmdVcTable. The value 0 indicates that no unassigned entries are available. To obtain the value of hwPwCmdVcIndex for a new entry in the hwPwCmdVcTable, the manager issues a management protocol retrieval operation to obtain the current value of hwPwCmdVcIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
hwPwCmdVcTable	1.3.6.1.4.1.2011.5.12.8.1.2.2		not-accessible	This table specifies information for configuring and status monitoring that are common to all service types. The index of this table is hwPwCmdVcIndex.
hwPwCmdVcEntry	1.3.6.1.4.1.2011.5.12.8.1.2.2.1		not-accessible	This table specifies information for configuring and status monitoring that are common to all service types. The index of this entry is hwPwCmdVcIndex.
U32 hwPwCmdVcIndex	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.1	Unsigned32	not-accessible	Index for the conceptual row identifying a PW within this PW Emulation table.
SIG hwPwCmdVcSignalProtocol	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.2	SignalProtocolType	read-create	Set by the operator to indicate the protocol responsible for establishing this PW. The value 'static' is used in all cases where no maintenance protocol (PW signaling) is used to set up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'ldp' is used in case of signaling with the Pwid FEC element with LDP signaling. The value 'rsvp' indicate the use of rsvp control protocol.
U32 hwPwCmdVcID	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.3	Unsigned32	read-create	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'.
PWV hwPwCmdVcType	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.4	PwVcType	read-create	This value indicate the service to be carried over this PW.
IPt hwPwCmdVcPeerAddrType	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.5	InetAddressType	read-create	Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown.
IP hwPwCmdVcPeerAddr	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.6	IpAddress	read-create	This object contains the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeros if not applicable (hwPwCmdVcPeerAddrType is 'unknown').
VCS hwPwCmdVcStatus	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.7	VcStatusType	read-only	Indicates the status of the PW in the local node.
U32 hwPwCmdVcInboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.8	Unsigned32	read-create	The PW label used in the inbound direction (i.e. packets received from the PSN. Range: 16-1023 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
U32 hwPwCmdVcOutboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.9	Unsigned32	read-create	The PW label used in the outbound direction (i.e. toward the PSN). Range: 16-1023 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
SIG hwPwCmdVcSwitchSignalProtocol	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.10	SignalProtocolType	read-create	Set by the operator to indicate the protocol responsible for establishing this PW. The value 'static' is used in all cases where no maintenance protocol (PW signaling) is used to set up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'ldp' is used in case of signaling with the Pwid FEC element with LDP signaling. The value 'rsvp' indicate the use of rsvp control protocol.
U32 hwPwCmdVcSwitchID	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.11	Unsigned32	read-create	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element' of the switch pw.
IPt hwPwCmdVcSwitchPeerAddrType	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.12	InetAddressType	read-create	Denotes the address type of the peer node of the switch pw. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown.
IP hwPwCmdVcSwitchPeerAddr	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.13	IpAddress	read-create	This object contains the value of the peer node address of the switch pw of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeros if not applicable (hwPwCmdVcSwitchPeerAddrType is 'unknown').
U32 hwPwCmdVcSwitchInboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.14	Unsigned32	read-create	The PW label used in the inbound direction (i.e. packets received from the PSN. Range: 16-1023 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
U32 hwPwCmdVcSwitchOutboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.15	Unsigned32	read-create	The PW label used in the outbound direction (i.e. toward the PSN). Range: 16-1023 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
U32 hwPwCmdVcGroupID	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.16	Unsigned32	read-only	Used in the Group ID field sent to the peer PWES within the maintenance protocol used for PW setup. Applicable if pwVcOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', should be set to zero otherwise.
NUM hwPwCmdVcIfIndex	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.17	InterfaceIndex	read-create	Index of the interface (or the virtual interface) associated with the PW.
INT hwPwCmdVcAcStatus	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.18	INTEGER	read-only	Local AC status. Options: 1. down(1) -indicates AC status down 2. up(2) -indicates AC status up 3. plugout(3) -indicates AC status plugout
U32 hwPwCmdVcMtu	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.19	Unsigned32	read-create	If not equal zero, the optional Mtu object in the signaling protocol will be sent with this value, representing the locally supported MTU size over the interface (or the virtual interface) associated with the PW.
T/F hwPwCmdVcCw	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.20	TruthValue	read-create	If signaling is used for PW establishment, this object indicates the status of the control word negotiation, and in both signaling or manual configuration indicates if CW is to be present or not for this PW.
BIT hwPwCmdVcVCCV	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.21	Bits	read-create	Indicates the optional VCCV capabilities of the pw. Options: 1. ccCw(0) 2. ccAlert(1) 3. ccLabel(2) 4. cvIcmpping(3) 5. cvLspping(4) 6. cvBfd(5)
U32 hwPwCmdVcBandwidth	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.22	Unsigned32	read-create	Indicates the bandwidth when signaling protocol is rsvp.
U32 hwPwCmdVcMaxAtmCells	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.23	Unsigned32	read-only	Indicates the max cell supported when vctype is atm.
OCT hwPwCmdVcTnlPolicyName	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.24	OCTET STRING	read-create	Indicates the tunnel policy name used.
U32 hwPwCmdVcQoSBehaviorIndex	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.25	Unsigned32	read-create	Indicates the traffic behavior Index when QOS is implemented.
OCT hwPwCmdVcExplicitPathName	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.26	OCTET STRING	read-create	Indicates the explicit path name set by the operator.
U32 hwPwCmdVcTemplateIndex	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.27	Unsigned32	read-create	Indicates the pw template index referenced.
T/F hwPwCmdVcSecondary	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.28	TruthValue	read-create	Indicates whether or not the secondary pw is used.
TIM hwPwCmdVcUpTime	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.29	TimeStamp	read-only	Specifies the total time this PW status has been Up(1).
ROW hwPwCmdVcRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.2.1.30	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
hwPwCmdVcTnlTable	1.3.6.1.4.1.2011.5.12.8.1.2.3		not-accessible	This table provides per-PW related tunnel information. The indexes of this table are hwPwCmdVcIndex and hwPwCmdVcTnlIndex, hwPwCmdVcIndexis set in hwPwCmdVcTable table.
hwPwCmdVcTnlEntry	1.3.6.1.4.1.2011.5.12.8.1.2.3.1		not-accessible	This table provides per-PW related tunnel information. The indexes of this entry are hwPwCmdVcIndex and hwPwCmdVcTnlIndex, hwPwCmdVcIndexis set in hwPwCmdVcTable table.
U32 hwPwCmdVcTnlIndex	1.3.6.1.4.1.2011.5.12.8.1.2.3.1.1	Unsigned32	read-only	Indicates the tunnel index related to each PW.
hwPwCmdRemoteVcTable	1.3.6.1.4.1.2011.5.12.8.1.2.4		not-accessible	This table provides remote PW information for each local PW.The index of this table is hwPwCmdRemoteVcID.
hwPwCmdRemoteVcEntry	1.3.6.1.4.1.2011.5.12.8.1.2.4.1		not-accessible	This table provides remote PW information for each local PW.The index of this entry is hwPwCmdRemoteVcID.
U32 hwPwCmdRemoteVcID	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.1	Unsigned32	read-only	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element' of the remote PW.
PWV hwPwCmdRemoteVcType	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.2	PwVcType	read-only	This value indicate the service to be carried over the remote PW.
VCS hwPwCmdRemoteVcStatus	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.3	VcStatusType	read-only	Indicates the status of the remote PW.
U32 hwPwCmdRemoteVcGroupID	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.4	Unsigned32	read-only	Indicates the Group ID field of the remote PW.
U32 hwPwCmdRemoteVcMtu	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.5	Unsigned32	read-only	Indicates the supported MTU size of the remote PW.
T/F hwPwCmdRemoteVcCw	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.6	TruthValue	read-only	Indicates the control word capability of the remote PW.
U32 hwPwCmdRemoteVcMaxAtmCells	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.7	Unsigned32	read-only	Indicates the max cell supported of the remote PW when vctype is atm.
T/F hwPwCmdRemoteVcNotif	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.8	TruthValue	read-only	Indicates notification is supported by the remote PW.
U32 hwPwCmdRemoteVcSwitchID	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.9	Unsigned32	read-only	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element' of the switch PW.
PWV hwPwCmdRemoteVcSwitchType	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.10	PwVcType	read-only	This value indicate the service to be carried over the switch PW.
VCS hwPwCmdRemoteVcSwitchStatus	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.11	VcStatusType	read-only	Indicates the status of the switch PW.
U32 hwPwCmdRemoteVcSwitchGroupID	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.12	Unsigned32	read-only	Indicates the Group ID field of the switch PW.
U32 hwPwCmdRemoteVcSwitchMtu	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.13	Unsigned32	read-only	Indicates the supported MTU size of the switch PW.
T/F hwPwCmdRemoteVcSwitchCw	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.14	TruthValue	read-only	Indicates the control word capability of the switch PW.
U32 hwPwCmdRemoteVcSwitchMaxAtmCells	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.15	Unsigned32	read-only	Indicates the max cell supported of the switch PW when vctype is atm.
T/F hwPwCmdRemoteVcSwitchNotif	1.3.6.1.4.1.2011.5.12.8.1.2.4.1.16	TruthValue	read-only	Indicates notification is supported by the switch PW.
hwPwCmdAcBindingTable	1.3.6.1.4.1.2011.5.12.8.1.2.5		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The indexes of this table are hwPwCmdAcBindingConnectIndex and hwPwCmdAcBindingPrimOrSecondary.
hwPwCmdAcBindingEntry	1.3.6.1.4.1.2011.5.12.8.1.2.5.1		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The indexes of this entry are hwPwCmdAcBindingConnectIndex and hwPwCmdAcBindingPrimOrSecondary.
U32 hwPwCmdAcBindingConnectIndex	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.1	Unsigned32	not-accessible	Indicates the connect index referenced. Range: 1-32768
U32 hwPwCmdAcBindingVcID	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.2	Unsigned32	read-create	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Range: 1-4294967295
VCS hwPwCmdAcBindingVcStatus	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.3	VcStatusType	read-only	Indicates the status of the PW: down(1), up(2), plugout(3).
OCT hwPwCmdAcBindingTemplateName	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.4	OCTET STRING	read-create	Indicates the description string of the template, MUST be NULL string if not applicable or not known yet.
I32 hwPwCmdAcBindingOutboundVpi	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.5	Integer32	read-create	VPI value of this ATM VC. Range: 0-4095 If the pwVcType is atmNto1Transparent then the value will be set to zero.
I32 hwPwCmdAcBindingOutboundVci	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.6	Integer32	read-create	VCI value of this ATM VC. Range: 32-65535 If the pwVcType is atmNto1Transparent, atmCell1to1Vpc or atmCellNto1Vpc then the value should be set to zero.
SIG hwPwCmdAcBindingSignalProtocol	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.7	SignalProtocolType	read-create	Set by the operator to indicate the protocol responsible for establishing this PW. The value 'static' is used in all cases where no maintenance protocol (PW signaling) is used to set up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'ldp' is used in case of signaling with the Pwid FEC element with LDP signaling. The value 'rsvp' indicate the use of rsvp control protocol.
I32 hwPwCmdAcBindingOutboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.8	Integer32	read-create	The PW label used in the outbound direction (i.e. toward the PSN). Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
I32 hwPwCmdAcBindingInboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.9	Integer32	read-create	The PW label used in the inbound direction (i.e. packets received from the PSN. Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
ROW hwPwCmdAcBindingRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.10	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
INT hwPwCmdAcBindingPrimOrSecondary	1.3.6.1.4.1.2011.5.12.8.1.2.5.1.11	INTEGER	not-accessible	This value indicate Primary PW or Secondary PW. Options: 1. primaryPW(1) -indicates primary PW 2. secondaryPW(2) -indicates secondary PW
U32 hwPwCmdTemplateIndexNext	1.3.6.1.4.1.2011.5.12.8.1.2.6	Unsigned32	read-only	This object contains an appropriate value to be used for hwPwCmdTemplateIndex when creating entries in the hwPwCmdTemplateTable. The value 0 indicates that no unassigned entries are available. To obtain the value of hwPwCmdTemplateIndex for a new entry in the hwPwCmdTemplateTable, the manager issues a management protocol retrieval operation to obtain the current value of hwPwCmdVcIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
hwPwCmdTemplateTable	1.3.6.1.4.1.2011.5.12.8.1.2.7		not-accessible	This table specifies information for configuring and status monitoring to pw template. The index of this table is hwPwCmdTemplateIndex.
hwPwCmdTemplateEntry	1.3.6.1.4.1.2011.5.12.8.1.2.7.1		not-accessible	This table specifies information for configuring and status monitoring to pw template. The index of this entry is hwPwCmdTemplateIndex.
U32 hwPwCmdTemplateIndex	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.1	Unsigned32	not-accessible	Index for the conceptual row identifying a PW template within this PW template table.
OCT hwPwCmdTemplateName	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.2	OCTET STRING	read-create	Indicates the description string of the template, MUST be NULL string if not applicable or not known yet.
PWV hwPwCmdTemplateVcType	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.3	PwVcType	read-create	This value indicate the service to be carried over this template.
IPt hwPwCmdTemplatePeerAddrType	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.4	InetAddressType	read-create	Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown.
IP hwPwCmdTemplatePeerAddr	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.5	IpAddress	read-create	This object contains the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeros if not applicable (hwPwCmdTemplatePeerAddrType is 'unknown').
U32 hwPwCmdTemplateMtu	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.6	Unsigned32	read-create	Indicates the supported MTU size of the switch PW. Range: 328-1710
T/F hwPwCmdTemplateCw	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.7	TruthValue	read-create	Indicates the control word capability of the switch PW.
BIT hwPwCmdTemplateVCCV	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.8	Bits	read-create	Indicates the optional VCCV capabilities of the pw. Options: 1. ccCw(0) 2. ccAlert(1) 3. ccLabel(2) 4. cvIcmpping(3) 5. cvLspping(4) 6. cvBfd(5)
T/F hwPwCmdTemplateFrag	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.9	TruthValue	read-create	Indicates whether or not fragmentation is supported.
U32 hwPwCmdTemplateBandwidth	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.10	Unsigned32	read-create	Indicates the bandwidth when signaling protocol is rsvp.
U32 hwPwCmdTemplateMaxAtmCells	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.11	Unsigned32	read-create	Indicates the max ATM cells when encapsulation is ATM. Range: 1-31 Default: 1
OCT hwPwCmdTemplateTnlPolicyName	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.12	OCTET STRING	read-create	Indicates the tunnel policy name used.
I32 hwPwCmdTemplateQoSBehaviorIndex	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.13	Integer32	read-create	Indicates the traffic behavior Index when QOS is implemented.
OCT hwPwCmdTemplateExplicitPathName	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.14	OCTET STRING	read-create	Indicates the explicit path name set by the operator.
U32 hwPwCmdTemplateTdmJitterBuffer	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.15	Unsigned32	read-create	Indicates the jitter buffer size of TDM PW. Range: 500-128000 Default: 2000 Unit: microsecond
U32 hwPwCmdTemplateTdmLoadTime	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.16	Unsigned32	read-create	Indicates the load time value of TDM PW. Range: 125-5000 Default: 1000 Unit: byte
INT hwPwCmdTemplateTdmRTP	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.17	INTEGER	read-create	Indicates enable or disable RTP of TDM PW. Options: 1. disable(0) -indicates disable RTP 2. enable(1) -indicates enable RTP Default: disable(0)
ROW hwPwCmdTemplateRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.18	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
U32 hwPwCmdTemplateTdmTimeSlotNum	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.19	Unsigned32	read-create	Indicates the time slot Num of TDM PW. Range: 1-32 Default: 32 Unit: byte
U32 hwPwCmdTemplateMaxEncapcellDelay	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.20	Unsigned32	read-create	Indicates the Max ATM cells encapsulate delay time. Range: 0-50 Default: 0 Unit: millisecond
BIT hwPwCmdTemplateFlowLabel	1.3.6.1.4.1.2011.5.12.8.1.2.7.1.21	Bits	read-create	Indicates the optional flow label capabilities of the pw.
hwPwCmdOperTable	1.3.6.1.4.1.2011.5.12.8.1.2.8		not-accessible	This table specifies the reset operation that can be done to the PW or PW template. The index of this table is hwPwCmdOperIndex.
hwPwCmdOperEntry	1.3.6.1.4.1.2011.5.12.8.1.2.8.1		not-accessible	This table specifies the reset operation that can be done to the PW or PW template. The index of this entry is hwPwCmdOperIndex.
U32 hwPwCmdOperIndex	1.3.6.1.4.1.2011.5.12.8.1.2.8.1.1	Unsigned32	not-accessible	Index for the conceptual row.
INT hwPwCmdOperType	1.3.6.1.4.1.2011.5.12.8.1.2.8.1.2	INTEGER	read-create	Specifies the reset object. Options: 1. vcindex(1) -indicates PW index 2. pwtindex(2) -indicates PW template index
U32 hwPwCmdOperVcOrPwtIndex	1.3.6.1.4.1.2011.5.12.8.1.2.8.1.3	Unsigned32	read-create	Specifies the object index to be reset.
INT hwPwCmdOperStatus	1.3.6.1.4.1.2011.5.12.8.1.2.8.1.4	INTEGER	read-only	Indicates the result of the reset operation. Options: 1. success(1) -indicates operation success 2. pwNotExist(2) -indicates PW not exist 3. pwTemplateNotExist(3) -indicates PW template not exist 4. resetFailure(4) -indicates reset PW failure 5. unknown(5) -indicates unknown operation status
TIM hwPwCmdOperTimeStamp	1.3.6.1.4.1.2011.5.12.8.1.2.8.1.5	TimeStamp	read-only	Specifies the total time since last reset operation has been done.
ROW hwPwCmdOperRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.8.1.6	RowStatus	read-create	For creating and deleting this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
T/F hwPwCmdVcSwitchNotifEnable	1.3.6.1.4.1.2011.5.12.8.1.2.9	TruthValue	read-write	If this object is set to true(1), then it enables the emission of hwPwCmdVcSwitchWtoP and hwPwCmdVcSwitchPtoW notifications; otherwise these notifications are not emitted, DEFVAL { false }
hwPwCmdAcVlanBindingTable	1.3.6.1.4.1.2011.5.12.8.1.2.10		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The indexes of this table are hwPwCmdAcVlanBindingVlanID and hwPwCmdAcVlanBindingPrimOrSecondary.
hwPwCmdAcVlanBindingEntry	1.3.6.1.4.1.2011.5.12.8.1.2.10.1		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The indexes of this entry are hwPwCmdAcVlanBindingVlanID and hwPwCmdAcVlanBindingPrimOrSecondary.
U32 hwPwCmdAcVlanBindingVlanID	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.1	Unsigned32	not-accessible	Indicates the VLAN ID referenced. Range: 2-4093
U32 hwPwCmdAcVlanBindingVcID	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.2	Unsigned32	read-create	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Range: 1-4294967295
VCS hwPwCmdAcVlanBindingVcStatus	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.3	VcStatusType	read-only	Indicates the status of the PW: down(1), up(2), plugout(3).
OCT hwPwCmdAcVlanBindingTemplateName	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.4	OCTET STRING	read-create	Indicates the description string of the template, MUST be NULL string if not applicable or not known yet.
SIG hwPwCmdAcVlanBindingSignalProtocol	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.5	SignalProtocolType	read-create	Set by the operator to indicate the protocol responsible for establishing this PW. The value 'static' is used in all cases where no maintenance protocol (PW signaling) is used to set up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'ldp' is used in case of signaling with the Pwid FEC element with LDP signaling. The value 'rsvp' indicate the use of rsvp control protocol.
I32 hwPwCmdAcVlanBindingOutboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.6	Integer32	read-create	The PW label used in the outbound direction (i.e. toward the PSN). Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
I32 hwPwCmdAcVlanBindingInboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.7	Integer32	read-create	The PW label used in the inbound direction (i.e. packets received from the PSN. Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
ROW hwPwCmdAcVlanBindingRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.8	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
INT hwPwCmdAcVlanBindingPrimOrSecondary	1.3.6.1.4.1.2011.5.12.8.1.2.10.1.9	INTEGER	not-accessible	This value indicate Primary PW or Secondary PW. Options: 1. primaryPW(1) -indicates primary PW 2. secondaryPW(2) -indicates secondary PW
hwPwCmdAcPvpBindingTable	1.3.6.1.4.1.2011.5.12.8.1.2.11		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The indexes of this table are ifIndex, hwPwCmdAcPvpBindingVpi and hwPwCmdAcPvpBindingPrimOrSecondary.
hwPwCmdAcPvpBindingEntry	1.3.6.1.4.1.2011.5.12.8.1.2.11.1		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The indexes of this entry are ifIndex, hwPwCmdAcPvpBindingVpi and hwPwCmdAcPvpBindingPrimOrSecondary.
U32 hwPwCmdAcPvpBindingVpi	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.1	Unsigned32	read-create	Indicates the VPI value. Range: 0-4095
U32 hwPwCmdAcPvpBindingVcID	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.2	Unsigned32	read-create	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Range: 1-4294967295
VCS hwPwCmdAcPvpBindingVcStatus	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.3	VcStatusType	read-only	Indicates the status of the PW: down(1), up(2), plugout(3).
OCT hwPwCmdAcPvpBindingTemplateName	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.4	OCTET STRING	read-create	Indicates the description string of the template, MUST be NULL string if not applicable or not known yet.
I32 hwPwCmdAcPvpBindingOutboundVpi	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.5	Integer32	read-create	Outbound VPI value of this ATM VC. Range: 0-4095
SIG hwPwCmdAcPvpBindingSignalProtocol	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.6	SignalProtocolType	read-create	Set by the operator to indicate the protocol responsible for establishing this PW. The value 'static' is used in all cases where no maintenance protocol (PW signaling) is used to set up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'ldp' is used in case of signaling with the Pwid FEC element with LDP signaling. The value 'rsvp' indicate the use of rsvp control protocol.
I32 hwPwCmdAcPvpBindingOutboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.7	Integer32	read-create	The PW label used in the outbound direction (i.e. toward the PSN). Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
I32 hwPwCmdAcPvpBindingInboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.8	Integer32	read-create	The PW label used in the inbound direction (i.e. packets received from the PSN. Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
INT hwPwCmdAcPvpBindingPrimOrSecondary	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.9	INTEGER	read-create	This value indicate Primary PW or Secondary PW. Options: 1. primaryPW(1) -indicates primary PW 2. secondaryPW(2) -indicates secondary PW
ROW hwPwCmdAcPvpBindingRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.11.1.10	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
hwPwCmdVccvTable	1.3.6.1.4.1.2011.5.12.8.1.2.12		not-accessible	This table specifies information for VCCV ping. The index of this table is hwPwCmdVccvVcID.
hwPwCmdVccvEntry	1.3.6.1.4.1.2011.5.12.8.1.2.12.1		not-accessible	This table specifies information for VCCV ping. The index of this entry is hwPwCmdVccvVcID.
U32 hwPwCmdVccvVcID	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.1	Unsigned32	read-create	This value indicate PW ID. Range: 1-4294967294
INT hwPwCmdVccvReplyMode	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.2	INTEGER	read-write	The reply mode for the VCCV packet. Options: 1. doNotReply(1) -indicates that there is no reply for VCCV PING 2. replyViaAnIPv4IPv6UdpPacket(2) -indicates that reply for VCCV PING using IP UDP packets 3. replyViaAnIPv4IPv6UdpPacketWithRouterAlert(3) -indicates that reply for VCCV PING using IP UDP packets with router alert 4. replyViaApplicationLevelControlChannel(4) -indicates that reply for VCCV PING using control channel
INT hwPwCmdVccvFrequency	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.3	INTEGER	read-write	The frequency of VCCV packet. Options: 1. freq1000ms(1000) -indicates VCCV PING frequency, interval is 1000 ms 2. freq2000ms(2000) -indicates VCCV PING frequency, interval is 2000 ms 3. freq5000ms(5000) -indicates VCCV PING frequency, interval is 5000 ms 4. freq10000ms(10000) -indicates VCCV PING frequency, interval is 10000 ms
U32 hwPwCmdVccvTimeoutLimit	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.4	Unsigned32	read-write	The timeout limit of VCCV ping. Range: 3-16
U32 hwPwCmdVccvRecoverLimit	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.5	Unsigned32	read-write	The recover limit of VCCV ping. Range: 1-16
U32 hwPwCmdVccvRemotePwVcID	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.6	Unsigned32	read-write	Indicates the PW Remote VcID in MH-PW. Range: 1-4294967295. When this leaf is set to 4294967295, it means that no remote PW ID is configured in the case of no creation, and that the configuration of remote PW ID is canceled in the case of modify operation.
IP hwPwCmdVccvRemoteIpAddress	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.7	IpAddress	read-write	Indicates the PW Remote IP address in MH-PW.
U32 hwPwCmdVccvTtl	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.8	Unsigned32	read-write	Indicates the PW TTL value. Range: 0-255. When this leaf is set to 0, it means that no ttl value is configured in the case of no creation, and that the configuration of TTL value is canceled in the case of modify operation.
INT hwPwCmdVccvPingStatus	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.9	INTEGER	read-only	Indicates the VCCV ping status. Options: 1. normal(0) -indicates that VCCV PING can get reply from the peer and the PW connection is normal 2. break(1) -indicates that VCCV PING cannot reach the peer and the PW connection is break 3. inactive(2) -indicates that VCCV PING is not in work mode
U32 hwPwCmdVccvPingSuccessNum	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.10	Unsigned32	read-only	The number of VCCV ping succeed. Range: 0-4294967295
U32 hwPwCmdVccvPingTimeOutNum	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.11	Unsigned32	read-only	The number of VCCV ping time out. Range: 0-4294967295
ROW hwPwCmdVccvRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.12	RowStatus	read-write	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state. Options: 1. active(1) -indicates query operation 2. createAndGo(4) -indicates creating an auto VCCV PING configuration 3. destroy(6) -indicates deleting an auto VCCV PING configuration
INT hwPwCmdVccvPingPipeUniform	1.3.6.1.4.1.2011.5.12.8.1.2.12.1.13	INTEGER	read-write	For setting VCCV ping mode. Options: 1. pipe(1) -indicates pipe mode of the VCCV ping. 2. uniform(2) -indicates uniform mode of the VCCV ping. Default: pipe(1)
hwPwCmdRecoverTable	1.3.6.1.4.1.2011.5.12.8.1.2.13		not-accessible	This table specifies information for recover mode of the PW. The index of this table is hwPwCmdRecoverVcID.
hwPwCmdRecoverEntry	1.3.6.1.4.1.2011.5.12.8.1.2.13.1		not-accessible	This table specifies information for recover mode of the PW. The index of this entry is hwPwCmdRecoverVcID.
U32 hwPwCmdRecoverVcID	1.3.6.1.4.1.2011.5.12.8.1.2.13.1.1	Unsigned32	not-accessible	Indicates the PW ID. Range: 1-4294967294
INT hwPwCmdRecoverType	1.3.6.1.4.1.2011.5.12.8.1.2.13.1.2	INTEGER	read-create	Indicates the recover mode of the PW. Options: 1. revertive(1) -indicates that automatic recovery is allowed 2. nonRevertive(2) -indicates that the traffic will not be switched back to the working PW automatically
U32 hwPwCmdRecoverWtrtime	1.3.6.1.4.1.2011.5.12.8.1.2.13.1.3	Unsigned32	read-create	Indicates the recover time. Range: 0,10-600 Unit: second
hwPwCmdManualSwitchoverTable	1.3.6.1.4.1.2011.5.12.8.1.2.14		not-accessible	This table specifies information for manual switchover. The index of this table is hwPwCmdManualSwitchoverVcID.
hwPwCmdManualSwitchoverEntry	1.3.6.1.4.1.2011.5.12.8.1.2.14.1		not-accessible	This table specifies information for manual switchover. The index of this entry is hwPwCmdManualSwitchoverVcID.
U32 hwPwCmdManualSwitchoverVcID	1.3.6.1.4.1.2011.5.12.8.1.2.14.1.1	Unsigned32	not-accessible	Indicates the primary PW ID. Range: 1-4294967294
INT hwPwCmdManualSwitchoverSwitchType	1.3.6.1.4.1.2011.5.12.8.1.2.14.1.2	INTEGER	read-create	Indicates the type of manual switchover. Options: 1. primaryPW(1) -indicates switch from primary PW to secondary PW 2. secondaryPW(2) -indicates switch from secondary PW to primary PW
hwPwCmdSwitchoverIpAddrTable	1.3.6.1.4.1.2011.5.12.8.1.2.15		not-accessible	This table specifies information for local and remote IP address to switch over. The index of this table is hwPwCmdSwitchoverPwId.
hwPwCmdSwitchoverIpAddrEntry	1.3.6.1.4.1.2011.5.12.8.1.2.15.1		not-accessible	This table specifies information for local and remote IP address to switch over. The index of this entry is hwPwCmdSwitchoverPwId.
U32 hwPwCmdSwitchoverPwId	1.3.6.1.4.1.2011.5.12.8.1.2.15.1.1	Unsigned32	read-create	Indicates the primary PW ID. Range: 1-4294967295
IP hwPwCmdSwitchoverLocalIpAddr	1.3.6.1.4.1.2011.5.12.8.1.2.15.1.2	IpAddress	read-create	Indicates switch over local IP address of PW.
IP hwPwCmdSwitchoverRemoteIpAddr	1.3.6.1.4.1.2011.5.12.8.1.2.15.1.3	IpAddress	read-create	Indicates switch over remote IP address of PW.
ROW hwPwCmdSwitchoverRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.15.1.4	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
hwPwCmdPsStatusTable	1.3.6.1.4.1.2011.5.12.8.1.2.16		not-accessible	This table specifies information for status of PW protect group. The index of this table is hwPwCmdPsPwId.
hwPwCmdPsStatusEntry	1.3.6.1.4.1.2011.5.12.8.1.2.16.1		not-accessible	This table specifies information for status of PW protect group. The index of this entry is hwPwCmdPsPwId.
U32 hwPwCmdPsPwId	1.3.6.1.4.1.2011.5.12.8.1.2.16.1.1	Unsigned32	not-accessible	Indicates the primary PW ID. Range: 1-4294967294
INT hwPwCmdPsPrimaryPwStatus	1.3.6.1.4.1.2011.5.12.8.1.2.16.1.2	INTEGER	read-only	Indicates status of primary PW. Options: 1. down(1) -indicates that the primary member of the PW protect group is down 2. upActive(2) -indicates that the primary member of the PW protect group is up and active 3. upStandby(3) -indicates that the primary member of the PW protect group is up and standby
INT hwPwCmdPsSecondaryPwStatus	1.3.6.1.4.1.2011.5.12.8.1.2.16.1.3	INTEGER	read-only	Indicates status of secondary PW. Options: 1. down(1) -indicates that the secondary member of the PW protect group is down 2. upActive(2) -indicates that the secondary member of the PW protect group is up and active 3. upStandby(3) -indicates that the secondary member of the PW protect group is up and standby
hwPwCmdPvcExpMapTable	1.3.6.1.4.1.2011.5.12.8.1.2.17		not-accessible	This table specifies information for PVC-EXP mapping. The indexes of this table are ifIndex, hwPwCmdPvcExpMapVpi, hwPwCmdPvcExpMapVci.
hwPwCmdPvcExpMapEntry	1.3.6.1.4.1.2011.5.12.8.1.2.17.1		not-accessible	This table specifies information for PVC-EXP mapping. The indexes of this entry are ifIndex, hwPwCmdPvcExpMapVpi, hwPwCmdPvcExpMapVci.
U32 hwPwCmdPvcExpMapVpi	1.3.6.1.4.1.2011.5.12.8.1.2.17.1.1	Unsigned32	read-create	Indicates the VPI value. Range: 0-4095
U32 hwPwCmdPvcExpMapVci	1.3.6.1.4.1.2011.5.12.8.1.2.17.1.2	Unsigned32	read-create	Indicates the VCI value. Range: 32-65535
U32 hwPwCmdPvcExpMapExp	1.3.6.1.4.1.2011.5.12.8.1.2.17.1.3	Unsigned32	read-create	Indicates the EXP value. Range: 0-7
ROW hwPwCmdPvcExpMapRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.17.1.4	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state. Options: 1. active(1) -indicates query operation 2. createAndGo(4) -indicates creating a mapping from PVC to MPLS EXP 3. destroy(6) -indicates deleting a mapping from PVC to MPLS EXP
hwPwCmdExpCosMapTable	1.3.6.1.4.1.2011.5.12.8.1.2.18		not-accessible	This table specifies information for EXP-COS mapping. The index of this table is hwPwCmdExpCosMapExp.
hwPwCmdExpCosMapEntry	1.3.6.1.4.1.2011.5.12.8.1.2.18.1		not-accessible	This table specifies information for EXP-COS mapping. The index of this entry is hwPwCmdExpCosMapExp.
U32 hwPwCmdExpCosMapExp	1.3.6.1.4.1.2011.5.12.8.1.2.18.1.1	Unsigned32	read-create	Indicates the EXP value. Range: 0-7
U32 hwPwCmdExpCosMapCos	1.3.6.1.4.1.2011.5.12.8.1.2.18.1.2	Unsigned32	read-create	Indicates the COS value. Range: 0-7
hwPwCmdTdmExpMapTable	1.3.6.1.4.1.2011.5.12.8.1.2.19		not-accessible	This table specifies information for TDM-EXP mapping. The index of this table is hwPwCmdTdmConnectId.
hwPwCmdTdmExpMapEntry	1.3.6.1.4.1.2011.5.12.8.1.2.19.1		not-accessible	This table specifies information for TDM-EXP mapping. The index of this entry is hwPwCmdTdmConnectId.
U32 hwPwCmdTdmConnectId	1.3.6.1.4.1.2011.5.12.8.1.2.19.1.1	Unsigned32	read-write	Indicates the TDM connect ID. Range: 0-2047
U32 hwPwCmdTdmExpMapExp	1.3.6.1.4.1.2011.5.12.8.1.2.19.1.2	Unsigned32	read-write	Indicates the EXP value. Range: 0-7 Default: 0
ROW hwPwCmdTdmExpMapRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.19.1.3	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state. Options: 1. active(1) -indicates query operation 2. createAndGo(4) -indicates creating a mapping from TDM to MPLS EXP 3. destroy(6) -indicates deleting a mapping from TDM to MPLS EXP
hwPwCmdAcTdmBindingTable	1.3.6.1.4.1.2011.5.12.8.1.2.20		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The indexes of this table are hwPwCmdAcTdmBindingTdmConnectId and hwPwCmdAcTdmBindingPrimOrSecondary.
hwPwCmdAcTdmBindingEntry	1.3.6.1.4.1.2011.5.12.8.1.2.20.1		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The indexes of this entry are hwPwCmdAcTdmBindingTdmConnectId and hwPwCmdAcTdmBindingPrimOrSecondary.
U32 hwPwCmdAcTdmBindingTdmConnectId	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.1	Unsigned32	read-write	Indicates the connect index referenced. Range: 0-1023
U32 hwPwCmdAcTdmBindingVcID	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.2	Unsigned32	read-write	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Range: 1-4294967294
VCS hwPwCmdAcTdmBindingVcStatus	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.3	VcStatusType	read-write	Indicates the status of the PW: down(1), up(2), plugout(3).
OCT hwPwCmdAcTdmBindingTemplateName	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.4	OCTET STRING	read-write	Indicates the description string of the template, MUST be NULL string if not applicable or not known yet.
I32 hwPwCmdAcTdmBindingEncapUDPPort	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.5	Integer32	read-write	Indicates UDP protocol encapsulation, UDP destination port. Range: 50000-57300
SIG hwPwCmdAcTdmBindingSignalProtocol	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.6	SignalProtocolType	read-write	Set by the operator to indicate the protocol responsible for establishing this PW. The value 'static' is used in all cases where no maintenance protocol (PW signaling) is used to set up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'ldp' is used in case of signaling with the Pwid FEC element with LDP signaling. The value 'rsvp' indicate the use of rsvp control protocol.
I32 hwPwCmdAcTdmBindingOutboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.7	Integer32	read-write	The PW label used in the outbound direction (i.e. toward the PSN). Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
I32 hwPwCmdAcTdmBindingInboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.8	Integer32	read-write	The PW label used in the inbound direction (i.e. packets received from the PSN. Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
INT hwPwCmdAcTdmBindingPrimOrSecondary	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.9	INTEGER	read-write	This value indicate Primary PW or Secondary PW. Options: 1. primaryPW(1) -indicates primary PW 2. secondaryPW(2) -indicates secondary PW
ROW hwPwCmdAcTdmBindingRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.20.1.10	RowStatus	read-write	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
hwPwCmdPwTable	1.3.6.1.4.1.2011.5.12.8.1.2.21		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The index of this table is hwPwCmdPwID.
hwPwCmdPwEntry	1.3.6.1.4.1.2011.5.12.8.1.2.21.1		not-accessible	This table specifies information for configuring and status monitoring for PW used in fixed network. The index of this entry is hwPwCmdPwID.
U32 hwPwCmdPwID	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.1	Unsigned32	read-write	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Range: 1-4294967294
OCT hwPwCmdPwTemplateName	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.2	OCTET STRING	read-create	Indicates the description string of the template, MUST be NULL string if not applicable or not known yet.
INT hwPwCmdPwAcBindMode	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.3	INTEGER	read-write	AcType. Options: 1. vlan(1) -indicates vlan 2. tdm(2) -indicates tdm 3. pvcfsp(3) -indicates pvc fsp 4. pvpfsp(4) -indicates pvp fsp
U32 hwPwCmdPwVlanID	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.4	Unsigned32	not-accessible	Indicates the VLAN ID referenced. Range: 2-4093
U32 hwPwCmdPwTdmVclID	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.5	Unsigned32	read-write	Indicates the connect index referenced. Range: 0-2047, 4294967295
I32 hwPwCmdPwIfindex	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.6	Integer32	read-create	Index of the interface (or the virtual interface) associated with the PW. Range: 1-2147483647, -1
I32 hwPwCmdPwVci	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.7	Integer32	read-create	Indicates the VPI value. Range: 32-65535, -1
I32 hwPwCmdPwVpi	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.8	Integer32	read-create	Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Range: 0-4095, -1
I32 hwPwCmdPwOutboundVci	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.9	Integer32	read-create	VCI value of this ATM VC. Range: 32-65535, -1 If the pwVcType is atmNto1Transparent, atmCell1to1Vpc or atmCellNto1Vpc then the value should be set to zero.
I32 hwPwCmdPwOutboundVpi	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.10	Integer32	read-create	VPI value of this ATM VC. Range: 0-4095, -1 If the pwVcType is atmNto1Transparent then the value will be set to zero.
U32 hwPwCmdPwImaGroup	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.11	Unsigned32	not-accessible	Indicates the VLAN ID referenced. Range: 0-4294967294
VCS hwPwCmdPwVcStatus	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.12	VcStatusType	read-only	Indicates the status of the PW: down(1), up(2), plugout(3).
I32 hwPwCmdPwEncapSrcUDPPort	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.13	Integer32	read-write	Indicates UDP protocol encapsulation, UDP destination port. Range: 50000-57300, -1
I32 hwPwCmdPwEncapDstUDPPort	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.14	Integer32	read-write	Indicates UDP protocol encapsulation, UDP destination port. Range: 49152-65535, -1
SIG hwPwCmdPwSignalProtocol	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.15	SignalProtocolType	read-create	Set by the operator to indicate the protocol responsible for establishing this PW. The value 'static' is used in all cases where no maintenance protocol (PW signaling) is used to set up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'ldp' is used in case of signaling with the Pwid FEC element with LDP signaling. The value 'rsvp' indicate the use of rsvp control protocol.
I32 hwPwCmdPwOutboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.16	Integer32	read-create	The PW label used in the outbound direction (i.e. toward the PSN). Range: 16-1048575, -1 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
U32 hwPwCmdPwInboundLabel	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.17	Unsigned32	read-create	The PW label used in the inbound direction (i.e. packets received from the PSN. Range: 16-1048575 It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF.
INT hwPwCmdPwPriority	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.18	INTEGER	read-write	This value indicate Primary PW or Secondary PW. Options: 1. primaryPW(1) -indicates primary PW 2. secondaryPW(2) -indicates secondary PW
ROW hwPwCmdPwRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.19	RowStatus	read-write	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state.
OCT hwPwCmdPwDesc	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.20	OCTET STRING	read-write	PW description, used to describe extra information of PW.
I32 hwPwCmdPwReceiveDstUDPPort	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.21	Integer32	read-write	Indicates UDP protocol encapsulation, UDP source port. Range: 50048-50111, -1
OCT hwPwCmdPwMultiPvc	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.22	OCTET STRING	read-write	Multi VCCs or VPCs string, include vpi,vci,outvpi and outvci.
INT hwPwCmdPwMultiPvcOp	1.3.6.1.4.1.2011.5.12.8.1.2.21.1.23	INTEGER	read-write	Multi VCCs or VPCs operate code, add or delete. Options: 1. add(1) -indicates add operation 2. delete(2) -indicates delete operation 3. invalidValue(-1) -indicates invalid value
hwPwCmdPwCarTable	1.3.6.1.4.1.2011.5.12.8.1.2.22		not-accessible	This table specifies information for PW CAR. The index of this table is hwPwCmdPWCarVcID.
hwPwCmdPwCarEntry	1.3.6.1.4.1.2011.5.12.8.1.2.22.1		not-accessible	This table specifies information for PW CAR. The index of this entry is hwPwCmdPWCarVcID.
U32 hwPwCmdPWCarVcID	1.3.6.1.4.1.2011.5.12.8.1.2.22.1.1	Unsigned32	not-accessible	Indicates the PW ID. Range: 1-4294967294
ROW hwPwCmdPWCarRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.22.1.4	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state. Options: 1. active(1) -indicates query operation 2. createAndGo(4) -indicates creating committed access rate parameters of a PW 3. destroy(6) -indicates deleting committed access rate parameters of a PW
U32 hwPwCmdPWCarCir	1.3.6.1.4.1.2011.5.12.8.1.2.22.1.5	Unsigned32	read-write	Committed information rate, it is the necessary parameter for adding pw car. Range: 1-1048575 Unit: 64Kbit/s
U32 hwPwCmdPWCarCbs	1.3.6.1.4.1.2011.5.12.8.1.2.22.1.6	Unsigned32	read-write	Committed burst size, default value is ((cir+8191)/8192+1). Range: 1-32767 Unit: 2KByte/s
U32 hwPwCmdPWCarPir	1.3.6.1.4.1.2011.5.12.8.1.2.22.1.7	Unsigned32	read-write	Peak information rate, default value is double of committed information rate. Range: 1-1048575 Unit: 64Kbit/s
U32 hwPwCmdPWCarPbs	1.3.6.1.4.1.2011.5.12.8.1.2.22.1.8	Unsigned32	read-write	Peak burst size, default value is MAX(((pir+8191)/8192 + 1), cbs). Range: 1-32767 Unit: 2KByte/s
hwPwCmdPvpExpMapTable	1.3.6.1.4.1.2011.5.12.8.1.2.23		not-accessible	This table specifies information for PVP-EXP mapping. The indexes of this table are ifIndex and hwPwCmdPvpExpMapVpi.
hwPwCmdPvpExpMapEntry	1.3.6.1.4.1.2011.5.12.8.1.2.23.1		not-accessible	This table specifies information for PVP-EXP mapping. The indexes of this entry are ifIndex and hwPwCmdPvpExpMapVpi.
U32 hwPwCmdPvpExpMapVpi	1.3.6.1.4.1.2011.5.12.8.1.2.23.1.1	Unsigned32	read-create	Indicates the VPI value. Range: 0-4095
U32 hwPwCmdPvpExpMapExp	1.3.6.1.4.1.2011.5.12.8.1.2.23.1.2	Unsigned32	read-create	Indicates the EXP value. Range: 0-7
ROW hwPwCmdPvpExpMapRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.23.1.3	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state. Options: 1. active(1) -indicates query operation 2. createAndGo(4) -indicates creating a mapping from PVP to MPLS EXP 3. destroy(6) -indicates deleting a mapping from PVP to MPLS EXP
INT hwMplsEcmpEnable	1.3.6.1.4.1.2011.5.12.8.1.2.24	INTEGER	read-write	Used to enable or disable the ECMP function. Options: 1. enable(1) -indicates that the ECMP function is enabled 2. disable(2) -indicates that the ECMP function is disabled Default: disable(2)
INT hwMplsL2VPNEnable	1.3.6.1.4.1.2011.5.12.8.1.2.25	INTEGER	read-write	Used to enable or disable the MPLS L2VPN function. Options: 1. enable(1) -indicates that the MPLS L2VPN function is enabled 2. disable(2) -indicates that the MPLS L2VPN function is disabled Default: disable(2)
hwPwExtTable	1.3.6.1.4.1.2011.5.12.8.1.2.26		not-accessible	This table specifies the extend information for configuring and status monitoring that are common to all service types and PSN types. The index of this table is pwIndex.
hwPwExtEntry	1.3.6.1.4.1.2011.5.12.8.1.2.26.1		not-accessible	This table specifies the extend information for configuring and status monitoring that are common to all service types and PSN types. The index of this entry is pwIndex.
INT hwPwPriority	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.1	INTEGER	read-write	This value indicate Primary PW or Secondary PW. Options: 1. primaryPW(1) -indicates the primary member of the PW protect group 2. secondaryPW(2) -indicates the secondary member of the PW protect group
U32 hwPwPrimaryPwIndex	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.2	Unsigned32	read-write	The value that represents the corresponding primary PW in the pwTable.
BIT hwPwVCCVCapabilities	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.3	Bits	read-write	Config the optional VCCV capabilities of the PW.
BIT hwPwVCCVStatus	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.4	Bits	read-only	Indicates the optional VCCV capabilities of the PW.
BIT hwPwFlowLabel	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.5	Bits	read-write	Indicates the optional flow label capabilities of the PW.
U32 hwPwAtmCfgTimeout	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.6	Unsigned32	read-write	Indicates max ATM cells encapsulation delay time. Range: 0-50 Default: 0 Unit: millisecond
OCT hwPwPriMappingProfName	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.7	OCTET STRING	read-write	QoS priority mapping profile name for PW, a string of 1-32 characters. There are all together 92 valid characters for the name. These characters include the following: uppercase and lowercase English letters (52 characters), numerals (0-9), and 30 symbols: ! # $ % & ' ( ) * + , - . / : ; @ [ \ ] ^ _ ` \| ~~.
BIT hwPwFlowLabelCapabilities	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.8	Bits	read-write	Indicates the PW flow label capability.
BIT hwPwFlowlabelStatus	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.9	Bits	read-only	Indicates the negotiation result of the PW flow label capability. The negotiation result of static PW is consistent with local configuration.
INT hwPwStatisticSwitch	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.10	INTEGER	read-write	Used to enable or disable the traffic statistic function of pw. Options: 1. enable(1) -indicates that the traffic statistic function is enabled 2. disable(2) -indicates that the traffic statistic function is disabled Default: disable(2)
OCT hwPwTnlPolicy	1.3.6.1.4.1.2011.5.12.8.1.2.26.1.11	OCTET STRING	read-write	Used to configure the tunnel policy used by the PW.
hwPwCmdTdmDefectStatsTable	1.3.6.1.4.1.2011.5.12.8.1.2.27		not-accessible	This table is a read-only table. The purpose of this table is to keep statistical information about the TDM failure alarm. The index of this table is pwIndex.
hwPwCmdTdmDefectStatsEntry	1.3.6.1.4.1.2011.5.12.8.1.2.27.1		not-accessible	This table is a read-only table. The purpose of this table is to keep statistical information about the TDM failure alarm. The index of this entry is pwIndex.
C32 hwPwCmdTdmDefectStatsJtrBfrOverRun	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.1	Counter32	read-only	Indicates the number of times that the jitter buffer overrun.
C32 hwPwCmdTdmDefectStatsJtrBfrOverRunClear	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.2	Counter32	read-only	Indicates the number of times that the system is restored from overrun of the jitter buffer.
C32 hwPwCmdTdmDefectStatsJtrBfrUnderRun	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.3	Counter32	read-only	Indicates the number of times that the jitter buffer overrun.
C32 hwPwCmdTdmDefectStatsJtrBfrUnderRunClear	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.4	Counter32	read-only	Indicates the number of times that the system is restored from underrun of the jitter buffer.
C32 hwPwCmdTdmDefectStatsR1	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.5	Counter32	read-only	Indicates the number of times that the PSN side receives an alarm triggered by R = 1. When the peer end didn't receive for failure. For example, jitter buffer underrun, Then the local end receives an packet with R = 1.
C32 hwPwCmdTdmDefectStatsR1Clear	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.6	Counter32	read-only	Indicates the number of times that the system is restored from R1.
C32 hwPwCmdTdmDefectStatsLM010	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.7	Counter32	read-only	Indicates the number of times that the PSN side receives an alarm triggered by M = 1. Only for the CESOPSN, When the local end receives a RDI alarm from the AC side, the local end sets the control flag M to 1. Then, the peer end receives an LM(010) packet.
C32 hwPwCmdTdmDefectStatsLM010Clear	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.8	Counter32	read-only	Indicates the number of times that the system is restored from LM(010) to LM(000).
C32 hwPwCmdTdmDefectStatsLM100	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.9	Counter32	read-only	Indicates the number of times that the PSN side receives an alarm triggered by L = 1. When the local end receives a LOS, LOF, AIS, or LMFA alarm from the AC side, the local end sets the control flag L to 1. Then, the peer end receives an LM(100) packet.
C32 hwPwCmdTdmDefectStatsLM100Clear	1.3.6.1.4.1.2011.5.12.8.1.2.27.1.10	Counter32	read-only	Indicates the number of times that the system is restored from LM(100) to LM(000).
hwPwPriMappingTable	1.3.6.1.4.1.2011.5.12.8.1.2.28		not-accessible	MPLS priority mapping profile table for PW. The purpose of this table is to set and query MPLS priority mapping profile. The index of this table is hwPwPriMappingProfileName.
hwPwPriMappingEntry	1.3.6.1.4.1.2011.5.12.8.1.2.28.1		not-accessible	MPLS priority mapping profile table for PW. The purpose of this table is to set and query MPLS priority mapping profile. The index of this entry is hwPwPriMappingProfileName.
OCT hwPwPriMappingProfileName	1.3.6.1.4.1.2011.5.12.8.1.2.28.1.1	OCTET STRING	not-accessible	QoS priority mapping profile name for PW, a string of 1-32 characters. There are all together 92 valid characters for the name. These characters include the following: uppercase and lowercase English letters (52 characters), numerals (0-9), and 30 symbols: ! # $ % & ' ( ) * + , - . / : ; @ [ \ ] ^ _ ` \| ~~.
OCT hwPwInboundInputPriList	1.3.6.1.4.1.2011.5.12.8.1.2.28.1.2	OCTET STRING	read-write	Inbound input priority list(MPLS PW label EXP) of QoS priority mapping. Legal character include: 0-7,hyphen,comma. Example legal string: 0,2,4-7.
OCT hwPwInboundOutputPriList	1.3.6.1.4.1.2011.5.12.8.1.2.28.1.3	OCTET STRING	read-write	Inbound output priority list(ethernet VLAN tag 802.1p) of QoS priority mapping. Legal character include: 0-7,hyphen,comma. Example legal string: 0,2,4-7.
OCT hwPwOutboundInputPriList	1.3.6.1.4.1.2011.5.12.8.1.2.28.1.4	OCTET STRING	read-write	Outbound input priority list(ethernet VLAN tag 802.1p) of QoS priority mapping. Legal character include: 0-7,hyphen,comma. Example legal string: 0,2,4-7.
OCT hwPwOutboundOutputPriList	1.3.6.1.4.1.2011.5.12.8.1.2.28.1.5	OCTET STRING	read-write	Outbound output priority list(MPLS PW label EXP) of QoS priority mapping. Legal character include: 0-7,hyphen,comma. Example legal string: 0,2,4-7.
ROW hwPwPriMappingProfileRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.28.1.6	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state. Options: 1. active(1) -indicates query operation 2. createAndGo(4) -indicates creating committed 3. destroy(6) -indicates deleting committed
hwPwCmdStatisticTable	1.3.6.1.4.1.2011.5.12.8.1.2.29		not-accessible	This table is used to query or clear the traffic statistic info of PW. The index of this table is pwIndex.
hwPwCmdStatisticEntry	1.3.6.1.4.1.2011.5.12.8.1.2.29.1		not-accessible	This table is used to query or clear the traffic statistic info of PW. The index of this entry is pwIndex.
C64 hwPwCmdStatisticUpstreamOctectsP0	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.1	Counter64	read-only	The total number of upstream octets with priority equel to 0.
C32 hwPwCmdStatisticUpstreamPacketsP0	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.2	Counter32	read-only	The total number of upstream packets with priority equel to 0.
C64 hwPwCmdStatisticUpstreamOctectsP1	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.3	Counter64	read-only	The total number of upstream octets with priority equel to 1.
C32 hwPwCmdStatisticUpstreamPacketsP1	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.4	Counter32	read-only	The total number of upstream packets with priority equel to 1.
C64 hwPwCmdStatisticUpstreamOctectsP2	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.5	Counter64	read-only	The total number of upstream octets with priority equel to 2.
C32 hwPwCmdStatisticUpstreamPacketsP2	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.6	Counter32	read-only	The total number of upstream packets with priority equel to 2.
C64 hwPwCmdStatisticUpstreamOctectsP3	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.7	Counter64	read-only	The total number of upstream octets with priority equel to 3.
C32 hwPwCmdStatisticUpstreamPacketsP3	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.8	Counter32	read-only	The total number of upstream packets with priority equel to 3.
C64 hwPwCmdStatisticUpstreamOctectsP4	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.9	Counter64	read-only	The total number of upstream octets with priority equel to 4.
C32 hwPwCmdStatisticUpstreamPacketsP4	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.10	Counter32	read-only	The total number of upstream packets with priority equel to 4.
C64 hwPwCmdStatisticUpstreamOctectsP5	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.11	Counter64	read-only	The total number of upstream octets with priority equel to 5.
C32 hwPwCmdStatisticUpstreamPacketsP5	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.12	Counter32	read-only	The total number of upstream packets with priority equel to 5.
C64 hwPwCmdStatisticUpstreamOctectsP6	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.13	Counter64	read-only	The total number of upstream octets with priority equel to 6.
C32 hwPwCmdStatisticUpstreamPacketsP6	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.14	Counter32	read-only	The total number of upstream packets with priority equel to 6.
C64 hwPwCmdStatisticUpstreamOctectsP7	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.15	Counter64	read-only	The total number of upstream octets with priority equel to 7.
C32 hwPwCmdStatisticUpstreamPacketsP7	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.16	Counter32	read-only	The total number of upstream packets with priority equel to 7.
C64 hwPwCmdStatisticDownstreamOctectsP0	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.17	Counter64	read-only	The total number of downstream octets with priority equel to 0.
C32 hwPwCmdStatisticDownstreamPacketsP0	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.18	Counter32	read-only	The total number of downstream packets with priority equel to 0.
C64 hwPwCmdStatisticDownstreamOctectsP1	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.19	Counter64	read-only	The total number of downstream octets with priority equel to 1.
C32 hwPwCmdStatisticDownstreamPacketsP1	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.20	Counter32	read-only	The total number of downstream packets with priority equel to 1.
C64 hwPwCmdStatisticDownstreamOctectsP2	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.21	Counter64	read-only	The total number of downstream octets with priority equel to 2.
C32 hwPwCmdStatisticDownstreamPacketsP2	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.22	Counter32	read-only	The total number of downstream packets with priority equel to 2.
C64 hwPwCmdStatisticDownstreamOctectsP3	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.23	Counter64	read-only	The total number of downstream octets with priority equel to 3.
C32 hwPwCmdStatisticDownstreamPacketsP3	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.24	Counter32	read-only	The total number of downstream packets with priority equel to 3.
C64 hwPwCmdStatisticDownstreamOctectsP4	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.25	Counter64	read-only	The total number of downstream octets with priority equel to 4.
C32 hwPwCmdStatisticDownstreamPacketsP4	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.26	Counter32	read-only	The total number of downstream packets with priority equel to 4.
C64 hwPwCmdStatisticDownstreamOctectsP5	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.27	Counter64	read-only	The total number of downstream octets with priority equel to 5.
C32 hwPwCmdStatisticDownstreamPacketsP5	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.28	Counter32	read-only	The total number of downstream packets with priority equel to 5.
C64 hwPwCmdStatisticDownstreamOctectsP6	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.29	Counter64	read-only	The total number of downstream octets with priority equel to 6.
C32 hwPwCmdStatisticDownstreamPacketsP6	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.30	Counter32	read-only	The total number of downstream packets with priority equel to 6.
C64 hwPwCmdStatisticDownstreamOctectsP7	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.31	Counter64	read-only	The total number of downstream octets with priority equel to 7.
C32 hwPwCmdStatisticDownstreamPacketsP7	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.32	Counter32	read-only	The total number of downstream packets with priority equel to 7.
INT hwPwCmdStatisticClear	1.3.6.1.4.1.2011.5.12.8.1.2.29.1.33	INTEGER	read-write	Clear the traffic statistics of this pw. Options: 1. clear(1) -clear the traffic statistics of this pw
INT hwPwStatisticClearAll	1.3.6.1.4.1.2011.5.12.8.1.2.30	INTEGER	read-write	Clear the traffic statistics of all PWs. Options: 1. clear(1) -clear the traffic statistics of all PWs
hwPwRedundancyTable	1.3.6.1.4.1.2011.5.12.8.1.2.31		not-accessible	This table specifies information for pw redundancy. The index of this table is pwIndex.
hwPwRedundancyEntry	1.3.6.1.4.1.2011.5.12.8.1.2.31.1		not-accessible	This table specifies information for pw redundancy. The index of this entry is pwIndex.
INT hwPwRedundancyMode	1.3.6.1.4.1.2011.5.12.8.1.2.31.1.1	INTEGER	read-create	Indicates the mode of the pw redundancy. Options: 1. master(1) -indicates that the pw redundancy mode is master 2. independent(2) -indicates that the pw redundancy mode is independent Default: master(1)
INT hwPwStreamDualReceiving	1.3.6.1.4.1.2011.5.12.8.1.2.31.1.2	INTEGER	read-create	Indicates the stream receiving mode of the pw redundancy. Options: 1. enable(1) -indicates that the stream receiving mode of the pw redundancy is dual 2. disable(2) -indicates that the stream receiving mode of the pw redundancy is single Default: disable(2)
hwPwCmdPwCarExtTable	1.3.6.1.4.1.2011.5.12.8.1.2.32		not-accessible	This table specifies information for PW CAR. The index of this table is pwIndex.
hwPwCmdPwCarExtEntry	1.3.6.1.4.1.2011.5.12.8.1.2.32.1		not-accessible	This table specifies information for PW CAR. The index of this entry is pwIndex.
U32 hwPwCmdPwCarExtCir	1.3.6.1.4.1.2011.5.12.8.1.2.32.1.1	Unsigned32	read-write	Committed information rate, it is the necessary parameter for adding pw car. Range: 1-1048575 Unit: 64Kbit/s
U32 hwPwCmdPwCarExtCbs	1.3.6.1.4.1.2011.5.12.8.1.2.32.1.2	Unsigned32	read-write	Committed burst size, default value is ((cir+8191)/8192+1). Range: 1-32767 Unit: 2KByte/s
U32 hwPwCmdPwCarExtPir	1.3.6.1.4.1.2011.5.12.8.1.2.32.1.3	Unsigned32	read-write	Peak information rate, default value is double of committed information rate. Range: 1-1048575 Unit: 64Kbit/s
U32 hwPwCmdPwCarExtPbs	1.3.6.1.4.1.2011.5.12.8.1.2.32.1.4	Unsigned32	read-write	Peak burst size, default value is MAX(((pir+8191)/8192 + 1), cbs). Range: 1-32767 Unit: 2KByte/s
ROW hwPwCmdPwCarExtRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.32.1.5	RowStatus	read-create	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state. Options: 1. active(1) -indicates query operation 2. createAndGo(4) -indicates creating committed access rate parameters of a PW 3. destroy(6) -indicates deleting committed access rate parameters of a PW
hwPwAutoVccvTable	1.3.6.1.4.1.2011.5.12.8.1.2.33		not-accessible	This table specifies information for PW VCCV ping. The index of this table is pwIndex.
hwPwAutoVccvEntry	1.3.6.1.4.1.2011.5.12.8.1.2.33.1		not-accessible	This table specifies information for PW VCCV ping. The index of this entry is pwIndex.
INT hwPwAutoVccvReplyMode	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.1	INTEGER	read-write	The reply mode for the VCCV packet. Options: 1. doNotReply(1) -indicates that there is no reply for VCCV PING 2. replyViaAnIPv4IPv6UdpPacket(2) -indicates that reply for VCCV PING using IP UDP packets 3. replyViaAnIPv4IPv6UdpPacketWithRouterAlert(3) -indicates that reply for VCCV PING using IP UDP packets with router alert 4. replyViaApplicationLevelControlChannel(4) -indicates that reply for VCCV PING using control channel
INT hwPwAutoVccvFrequency	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.2	INTEGER	read-write	The frequency of VCCV packet. Options: 1. freq1000ms(1000) -indicates VCCV PING frequency, interval is 1000 ms 2. freq2000ms(2000) -indicates VCCV PING frequency, interval is 2000 ms 3. freq5000ms(5000) -indicates VCCV PING frequency, interval is 5000 ms 4. freq10000ms(10000) -indicates VCCV PING frequency, interval is 10000 ms
U32 hwPwAutoVccvTimeoutLimit	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.3	Unsigned32	read-write	The timeout limit of VCCV ping. Range: 3-16
U32 hwPwAutoVccvRecoverLimit	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.4	Unsigned32	read-write	The recover limit of VCCV ping. Range: 1-16
U32 hwPwAutoVccvRemotePwID	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.5	Unsigned32	read-write	Indicates the PW Remote VcID in MH-PW. Range: 1-4294967295. When this leaf is set to 4294967295, it means that no remote PW ID is configured in the case of no creation, and that the configuration of remote PW ID is canceled in the case of modify operation.
IP hwPwAutoVccvRemoteIpAddress	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.6	IpAddress	read-write	Indicates the PW Remote IP address in MH-PW.
U32 hwPwAutoVccvTtl	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.7	Unsigned32	read-write	Indicates the PW TTL value. Range: 0-255. When this leaf is set to 0, it means that no ttl value is configured in the case of no creation, and that the configuration of TTL value is canceled in the case of modify operation.
INT hwPwAutoVccvPingStatus	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.8	INTEGER	read-only	Indicates the VCCV ping status. Options: 1. normal(0) -indicates that VCCV PING can get reply from the peer and the PW connection is normal 2. break(1) -indicates that VCCV PING cannot reach the peer and the PW connection is break 3. inactive(2) -indicates that VCCV PING is not in work mode
U32 hwPwAutoVccvPingSuccessNum	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.9	Unsigned32	read-only	The number of VCCV ping succeed. Range: 0-4294967295
U32 hwPwAutoVccvPingTimeOutNum	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.10	Unsigned32	read-only	The number of VCCV ping time out. Range: 0-4294967295
INT hwPwAutoVccvStatisticsReset	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.11	INTEGER	read-write	Clear the traffic statistics of this pw. Options: 1. reset(1) -reset the traffic statistics of this PW
INT hwPwAutoVccvPipeUniform	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.12	INTEGER	read-write	For setting VCCV ping mode. Options: 1. pipe(1) -indicates pipe mode of the VCCV ping. 2. uniform(2) -indicates uniform mode of the VCCV ping. Default: pipe(1)
ROW hwPwAutoVccvRowStatus	1.3.6.1.4.1.2011.5.12.8.1.2.33.1.13	RowStatus	read-write	For creating and modifying this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state. Options: 1. active(1) -indicates query operation 2. createAndGo(4) -indicates creating an auto VCCV PING configuration 3. destroy(6) -indicates deleting an auto VCCV PING configuration
hwPwCmdConformance	1.3.6.1.4.1.2011.5.12.8.1.3
hwPwCmdGroups	1.3.6.1.4.1.2011.5.12.8.1.3.1
hwPwCmdVcGroup	1.3.6.1.4.1.2011.5.12.8.1.3.1.1			Collection of objects that are required in all implementations that support the PW CMD MIB module.
hwPwCmdRemoteVcGroup	1.3.6.1.4.1.2011.5.12.8.1.3.1.2			Collection of objects that are required by remote PW.
hwPwCmdTemplateGroup	1.3.6.1.4.1.2011.5.12.8.1.3.1.3			Collection of objects required to perform pw template related commands.
hwPwCmdOperGroup	1.3.6.1.4.1.2011.5.12.8.1.3.1.4			Collection of objects required to perform pw reset related commands.
hwPwCmdNonIfGroup	1.3.6.1.4.1.2011.5.12.8.1.3.1.5			Collection of objects that are required in fixed network.
hwPwCmdVcNotificationControlGroup	1.3.6.1.4.1.2011.5.12.8.1.3.1.6			Collection of objects for controlling the PW notifications.
hwPwCmdVcNotificationGroup	1.3.6.1.4.1.2011.5.12.8.1.3.1.7			Collection PW notifications objects.
hwPwCmdTrapsVbOids	1.3.6.1.4.1.2011.5.12.8.1.4
I32 hwPwCmdTunnId	1.3.6.1.4.1.2011.5.12.8.1.4.1	Integer32	accessible-for-notify	Indicates the index of tunnel. Range: 1-64
hwPwCmdTraps	1.3.6.1.4.1.2011.5.12.8.1.5
hwPwCmdCommonTraps	1.3.6.1.4.1.2011.5.12.8.1.5.1
hwPwCmdCommonTrapsPrefix	1.3.6.1.4.1.2011.5.12.8.1.5.1.0
NTF hwPwCmdPwStatus	1.3.6.1.4.1.2011.5.12.8.1.5.1.0.1			This notification is generated when the pw's status changed.
NTF hwPwCmdPwDeleted	1.3.6.1.4.1.2011.5.12.8.1.5.1.0.2			This notification is generated when the pw's deleted.
hwPwCmdAlarmTraps	1.3.6.1.4.1.2011.5.12.8.1.5.2
hwPwCmdAlarmTrapsPrefix	1.3.6.1.4.1.2011.5.12.8.1.5.2.0
NTF hwPwCmdSerRecov	1.3.6.1.4.1.2011.5.12.8.1.5.2.0.1			This notification is generated when the pw recovered the service. The first object is the index of the first pw, and the other is the index of the last pw.
NTF hwPwCmdSerFault	1.3.6.1.4.1.2011.5.12.8.1.5.2.0.2			This notification is generated when the pw service has some faults. The first object is the index of the first pw, and the other is the index of the last pw.
NTF hwPwCmdSerSwitchToSec	1.3.6.1.4.1.2011.5.12.8.1.5.2.0.3			This notification is generated when the service switches over to the secondary PW. The first object is the index of primary pw, and the other is the index of secondary pw.
NTF hwPwCmdSerSwitchToPri	1.3.6.1.4.1.2011.5.12.8.1.5.2.0.4			This notification is generated when the service switches over to the primary PW. The first object is the index of primary pw, and the other is the index of secondary pw.
NTF hwPwCmdTunnSwitchToW	1.3.6.1.4.1.2011.5.12.8.1.5.2.0.5			This notification is generated when the MPLS service switches from the protect tunnel to the work tunnel. The first object is the index of work-tunnel, and the other is the index of protect-tunnel.
NTF hwPwCmdTunnSwitchToP	1.3.6.1.4.1.2011.5.12.8.1.5.2.0.6			This notification is generated when the MPLS service switches from the work-tunnel to the protect-tunnel. The first object is the index of protect-tunnel, and the other is the index of work-tunnel.

RFC description

Manages Pseudo Wire Emulation (PWE3) for L2 VPN services including ATM and Ethernet private line emulation over MPLS.

Start monitoring Huawei MPLS-capable router/switch supporting PWE3 pseudowire services with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-PW-CMD-MIB

What Is HUAWEI-PW-CMD-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description