HUAWEI-MINM-MIB

All MIBs › HUAWEI-MINM-MIB

Organization: Huawei Technologies Co., Ltd.

Last Updated: 2006-11-23

Category: Device Management, Protocol: LLDP, Vendor: Huawei

Description: Huawei MINM (Minimized Network Management) MIB for simplified element management and configuration in carrier access networks.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-MINM-MIB?

HUAWEI-MINM-MIB is a Huawei MIB supporting the MINM (Minimized Network Management) feature, a lightweight management model intended for carrier access-network elements that don't need the full overhead of a conventional NMS/MIB stack. It exposes configuration data controlling the MINM feature itself, such as whether it is enabled and its associated parameters. Its monitoring value is software feature status: confirming a remote access element is operating in the expected minimized-management mode and that its lightweight configuration parameters are set as intended, which is important since a misconfigured MINM state can mean the element isn't being reached the way operations expects. It's designed to reduce reliance on heavier management protocols rather than to extend a particular external standard. It is deployed on carrier access-network elements such as ONTs or small access nodes managed at scale with reduced per-device overhead, with the HUAWEI-MINM-MIB MIB defining the configuration objects that control this lightweight mode.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-MINM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei carrier access network elements
Huawei ONT/access nodes

Monitoring Examples

No sample object names were provided for this module. Based on the module description, an administrator would check the MINM feature's enable/disable status and its configuration parameters to confirm a given access element is correctly operating under minimized management, and would notice a problem if a device unexpectedly reverted to full management mode or lost its lightweight configuration.

What Can Be Monitored

MINM feature enable/disable status
MINM configuration parameters

Imported Objects

From HUAWEI-L2IF-MIB

VlanList

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From IANA-ADDRESS-FAMILY-NUMBERS-MIB

AddressFamilyNumbers

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From P-BRIDGE-MIB

EnabledStatus

From Q-BRIDGE-MIB

VlanId
VlanIdOrNone

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

From TRANSPORT-ADDRESS-MIB

TransportAddress
TransportDomain

How to Use in IPNetwork Monitor

Example using hwMinMMacTnlInPackets OID:

Select a Huawei carrier access-network element / ONT (Minimized Network Management) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hwMinMMacTnlInPackets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Indicates the number of packets received by the mac-tunnel. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwMINM	1.3.6.1.4.1.2011.5.25.133
hwMinMMIB	1.3.6.1.4.1.2011.5.25.133.1			The HUAWEI-MINM-MIB contains objects to Manage configuration for MINM feature.
hwMinMObjects	1.3.6.1.4.1.2011.5.25.133.1.1
hwMinMSystemObjects	1.3.6.1.4.1.2011.5.25.133.1.1.1
MAC hwMinMVirtualMac	1.3.6.1.4.1.2011.5.25.133.1.1.1.1	MacAddress	read-write	Indicates the virtual MAC address of the device. By default, there is no virtual MAC address.
VLA hwMinMMacTnlBVlanListLow	1.3.6.1.4.1.2011.5.25.133.1.1.1.2	VlanList	read-write	Indicates the starting value of the backbone VLAN that is assigned to the mac-tunnel.
VLA hwMinMMacTnlBVlanListHigh	1.3.6.1.4.1.2011.5.25.133.1.1.1.3	VlanList	read-write	Indicates the ending value of the backbone VLAN that is assigned to the mac-tunnel.
ENA hwMinMTrapEnable	1.3.6.1.4.1.2011.5.25.133.1.1.1.4	EnabledStatus	read-write	Indicates that the Snmp-Agent Trap is enabled on the Mac-in-Mac.By default, it is disable.
hwMinMMacTnlObjects	1.3.6.1.4.1.2011.5.25.133.1.1.2
hwMinMMacTnlCfgObjects	1.3.6.1.4.1.2011.5.25.133.1.1.2.1
U32 hwMinMMacTnlIndexNext	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.1	Unsigned32	read-only	Indicates the Index of the Next Mac Tunnel.It begins with one.
hwMinMMacTnlCfgTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2		not-accessible	Indicates a configuration information table of Mac-tunnel.
hwMinMMacTnlCfgEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1		not-accessible	Indicates the entry in the tunnel configuration table of the mac-tunnel.
U32 hwMinMMacTnlIndex	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.1	Unsigned32	not-accessible	Indicates the index of Mac Tunnel. It begins with one.
OCT hwMinMMacTnlName	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.11	OCTET STRING	read-create	Indicates the name of the mac-tunnel. It is a character string with a maximum of 31 bytes and a minimum of 1 byte.
MAC hwMinMMacTnlDMac	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.12	MacAddress	read-create	Indicates the remote MAC address of the current mac-tunnel. By default, there is no such configuration.
VLA hwMinMMacTnlBVlanID	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.13	VlanIdOrNone	read-create	Indicates BVLAN value of the current BVLAN used by the mac-tunnel: It ranges from 1 to 4094. By default, BVLAN value is not configured. The VLAN here must have been created and be in the backbone VLAN used by the mac-tunnel. The special value of zero is used to indicate that no VLAN-ID is present or used.
OCT hwMinMMacTnlBVlanType	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.14	OCTET STRING	read-create	Indicates the B-TAG type of the BVLAN. By default, it is 88a8.
I32 hwMinMMacTnlPriorityValue	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.15	Integer32	read-create	Indicates priority level of the mac-tunnel. It is used to set the priority field of B-TAG. There are eight priority levels. By default, the I-TAG priority is used. The special value of eight is used to indicate that priority was unknown or none.
NUM hwMinMMacTnlOutgoingIfIndex	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.16	InterfaceIndexOrZero	read-create	Indicates the port used in the mac-tunnel. By default, it is not configured. The value zero is used to indicate that interface was unknown or none.
ENA hwMinMMacTnlSplitHorizonEnable	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.17	EnabledStatus	read-create	Indicates the split horizon of tunnels. By default, it is enabled. When split horizon is enabled on two mac-tunnels, the two tunnels cannot exchange packets.
HWA hwMinMMacTnlAdminStatus	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.18	HWAdminStatus	read-create	Indicates the administration status of the mac-tunnel.
HWO hwMinMMacTnlOperStatus	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.19	HWOperStatus	read-only	Indicates the physical state of the mac-tunnel.
OCT hwMinMMacTnlDescription	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.20	OCTET STRING	read-create	Indicates descriptive information of the static Mac-In-Mac tunnel. Its length ranges from 1 to 80 bytes and the first byte cannot be a space.
ENA hwMinMMacTnlStatisticsReset	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.21	EnabledStatus	read-create	Indicates the reset on traffic statistics of the mac-tunnel.
T/F hwMinMMacTnlPriorityTrustITag	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.22	TruthValue	read-create	Indicates that the I-TAG priority is copied to the mac-tunnel. By default, the I-TAG priority is not copied to the mac-tunnel.
T/F hwMinMMacTnlDeiTrustIDei	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.23	TruthValue	read-create	Indicates that the I-DEI priority is copied to the mac-tunnel. By default, the I-DEI priority is not copied to the mac-tunnel.
I32 hwMinMMacTnlDeiValue	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.24	Integer32	read-create	Indicates DEI of the mac-tunnel. It is used to set the DEI field of B-TAG. When DEI is true, the value is set to 1. When DEI is false, the value is set to 0. By default, the I-DEI priority is not copied to the mac-tunnel, and the DEI is false. When the value of the DEI is set to 2, it indicates that no DEI is configured on the tunnel.
ROW hwMinMMacTnlRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.2.1.51	RowStatus	read-create	Indicates the RowStatus. The following three actions are used: active, createAndGo, destroy
hwMinMMacTnlStatisticsTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.3		not-accessible	Indicates a query for the hwMinMMacTnlStatisticsTable of the mac-tunnel.
hwMinMMacTnlStatisticsEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.3.1		not-accessible	Indicates an entry query for the hwMinMMacTnlStatisticsTable of the mac-tunnel.
C64 hwMinMMacTnlInPacketsEx	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.3.1.11	Counter64	read-only	Indicates the number of packets received by the mac-tunnel.
C64 hwMinMMacTnlInBytes	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.3.1.12	Counter64	read-only	Indicates the number of bytes received by the mac-tunnel.
C64 hwMinMMacTnlOutPackets	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.3.1.13	Counter64	read-only	Indicates the number of packets sent by the mac-tunnel.
C64 hwMinMMacTnlOutBytes	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.3.1.14	Counter64	read-only	Indicates the number of bytes sent by the mac-tunnel.
hwMacTnlNameToIndexMappingTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.4		not-accessible	Indicates the mapping table of the tunnel name and tunnel index.
hwMacTnlNameToIndexMappingEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.4.1		not-accessible	Indicates the mapping table entry of the tunnel name and tunnel index.
OCT hwMacTnlName	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.4.1.1	OCTET STRING	not-accessible	Indicates the name of the mac-tunnel. It is a character string with a maximum of 31 bytes and a minimum of 1 byte.
U32 hwMacTnlIndex	1.3.6.1.4.1.2011.5.25.133.1.1.2.1.4.1.11	Unsigned32	read-only	Indicates the tunnel index.It begins with one.
hwMinMMacTnlOamObjects	1.3.6.1.4.1.2011.5.25.133.1.1.2.2
hwMinMMacTnlCCTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.1		not-accessible	Indicates the parameters used to describe CC packets.
hwMinMMacTnlCCEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.1.1		not-accessible	Indicates the CC table entry.
ENA hwMinMMacTnlCfmEnable	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.1.1.11	EnabledStatus	read-create	Indicates that CFM is enabled.
NUM hwMinMMacTnlCCInterval	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.1.1.12	HwDot1agCfmCcmInterval	read-create	Indicates the time interval of CC packets.
T/F hwMinMMacTnlSomeRMepCcmDefect	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.1.1.13	TruthValue	read-only	Indicates a connectivity failure of tunnels.
T/F hwMinMMacTnlSomeRdiDefect	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.1.1.14	TruthValue	read-only	Indicates whether the RDI packet from the remote end is received.
T/F hwMinMMacTnlCcReceiveEnabled	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.1.1.15	TruthValue	read-create	Whether CC reception is enabled.
ROW hwMinMMacTnlCCRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.1.1.51	RowStatus	read-create	Indicates the row status.
hwMinMMacTnlLbTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2		not-accessible	Indicates the parameters used to describe Lb packets.
hwMinMMacTnlLbEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1		not-accessible	Indicates the loopback table entry.
ENA hwMinMMacTnlLbmEnable	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1.11	EnabledStatus	read-create	Indicates that the MAC Ping is started inside the tunnel.
TIM hwMinMMacTnlLbmTimeStamp	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1.12	TimeStamp	read-only	Indicates the operation time.
I32 hwMinMMacTnlLbmTimeOut	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1.13	Integer32	read-create	Indicates the timeout period entered by a user, in ms. By default, it is 2000.
I32 hwMinMMacTnlLbmTimes	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1.14	Integer32	read-create	Indicates the number of times that Ping is entered.
I32 hwMinMMacTnlLbmSize	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1.15	Integer32	read-create	Indicates the size of an Lbm packet.
C32 hwMinMMacTnlLbrIn	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1.16	Counter32	read-only	Indicates the number of valid LBR packets received
T/F hwMinMMacTnlLbmResult	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1.17	TruthValue	read-only	Whether the MAC ping operation for a tunnel is over.
ROW hwMinMMacTnlLbRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.2.1.51	RowStatus	read-create	Indicates the row status.
hwMinMMacTnlLbResultTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.3		not-accessible	Performance statistics returned by using the MAC ping command for a tunnel.
hwMinMMacTnlLbResultEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.3.1		not-accessible	Indicates the loopback table entry.
G32 hwMinMMacTnlMacPingRTTMin	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.3.1.11	Gauge32	read-only	The minimum round trip time.
G32 hwMinMMacTnlMacPingRTTMax	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.3.1.12	Gauge32	read-only	The maximum round trip time.
G32 hwMinMMacTnlMacPingRTTAvg	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.3.1.13	Gauge32	read-only	The average round trip time.
G32 hwMinMMacTnlMacPingPacketLossRatio	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.3.1.14	Gauge32	read-only	The packet loss ratio.
hwMinMMacTnlLtmTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4		not-accessible	Indicates the parameters used to describe Ltm packets.
hwMinMMacTnlLtmEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1		not-accessible	Indicates the linktrace table entry.
ENA hwMinMMacTnlLtmEnable	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.11	EnabledStatus	read-create	Indicates that the MAC Trace is started inside the tunnel.
TIM hwMinMMacTnlLtmTimeStamp	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.12	TimeStamp	read-only	The time stamp for enabling the MAC trace operation for a tunnel.
I32 hwMinMMacTnlLtmTimeOut	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.13	Integer32	read-create	Indicates the timeout period entered by a user, in ms. By default, it is 2000.
U32 hwMinMMacTnlLtmTtl	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.14	Unsigned32	read-create	Indicates the living cycle of Ltm packets.
BIT hwMinMMacTnlLtmFlags	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.15	Bits	read-only	The flags field of an LTM packet.
U32 hwMinMMacTnlLtmSeqNumber	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.16	Unsigned32	read-only	The sequence number of an LTM packet.
U32 hwMinMMacTnlLtmEgressIdentifier	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.17	Unsigned32	read-create	Indicates the egress ID of Ltm packets.
T/F hwMinMMacTnlLtmResult	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.18	TruthValue	read-only	Two conditions are used to determine whether the MAC trace operation to a tunnel is over: (1) The peer of a tunnel has been traced. (2) The preset timer for timeout is triggered. Either condition indicates the completion of an operation.
ROW hwMinMMacTnlLtmRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.4.1.51	RowStatus	read-create	Indicates the row status.
hwMinMMacTnlLtrTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5		not-accessible	Indicates the parameters used to describe Ltr packets.
hwMinMMacTnlLtrEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1		not-accessible	Indicates the linktraceRelay table entry.
U32 hwMinMMacTnlLtrSeqNumber	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.1	Unsigned32	not-accessible	Indicates the parameters used to describe Ltr packets.
U32 hwMinMMacTnlLtrReceiveOrder	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.2	Unsigned32	not-accessible	An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value.
U32 hwMinMMacTnlLtrTtl	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.11	Unsigned32	read-only	TTL field value for a returned LTR.
T/F hwMinMMacTnlLtrForwarded	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.12	TruthValue	read-only	Indicates an identifier that shows whether the LTM packet should be forwarded to the next hop.
OCT hwMinMMacTnlLtrLastEgressIdentifier	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.13	OCTET STRING	read-only	LTR packet is a response packet to a LTM packet. The LTM packet is the last packet sent by a port on a device. This variable indicates the port identifier of the LTM packet. The last six bytes indicate the MAC address, and the first two bytes represent the board number and outbound port number respectively.
OCT hwMinMMacTnlLtrNextEgressIdentifier	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.14	OCTET STRING	read-only	If the LTM packet needs to be forwarded to the next hop, the port identifier of the next hop should be added to the TVL field in the response LTR packet. The last six bytes indicate the MAC address, and the first two bytes represent the board number and outbound port number respectively.
HWD hwMinMMacTnlLtrRelay	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.15	HwDot1agCfmRelayActionFieldValue	read-only	Indicates the value in the Relay Action field.
HWD hwMinMMacTnlLtrIngress	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.16	HwDot1agCfmIngressActionFieldValue	read-only	The value returned in the Ingress Action Field of the LTM.
MAC hwMinMMacTnlLtrIngressMac	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.17	MacAddress	read-only	MAC address returned in the ingress MAC address field.
HWL hwMinMMacTnlLtrIngressPortIdSubtype	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.18	HwLldpPortIdSubtype	read-only	Format of the Ingress Port ID.
HWL hwMinMMacTnlLtrIngressPortId	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.19	HwLldpPortId	read-only	Ingress Port ID. The format of this object is determined by the value of the dot1agCfmLtrIngressPortIdSubtype object.
HWD hwMinMMacTnlLtrEgress	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.20	HwDot1agCfmEgressActionFieldValue	read-only	The value returned in the Egress Action Field of the LTM.
MAC hwMinMMacTnlLtrEgressMac	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.21	MacAddress	read-only	MAC address returned in the egress MAC address field.
HWL hwMinMMacTnlLtrEgressPortIdSubtype	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.22	HwLldpPortIdSubtype	read-only	Format of the egress Port ID.
HWL hwMinMMacTnlLtrEgressPortId	1.3.6.1.4.1.2011.5.25.133.1.1.2.2.5.1.23	HwLldpPortId	read-only	Egress Port ID. The format of this object is determined by the value of the dot1agCfmLtrEgressPortIdSubtype object.
hwMinMMacTnlApsObjects	1.3.6.1.4.1.2011.5.25.133.1.1.2.3
hwMinMMacTnlApsCfgTable	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1		not-accessible	Indicates the configuration table for the Aps protection of the mac-tunnel.
hwMinMMacTnlApsCfgEntry	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1		not-accessible	Indicates the configuration table entry for the Aps protection of the mac-tunnel.
U32 hwMinMProtectMacTnlIndex	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.11	Unsigned32	read-only	Indicates the index of ProtectMacTunnel. It begins with one.
OCT hwMinMProtectMacTnlName	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.12	OCTET STRING	read-create	Indicates the tunnel name of the protective mac-tunnel.
MAC hwMinMProtectMacTnlDMac	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.13	MacAddress	read-only	Indicates the remote MAC address of the protecting mac-tunnel.
VLA hwMinMProtectMacTnlBVlanID	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.14	VlanId	read-only	Indicates BVLAN value used by the protecting mac-tunnel: It ranges from 1 to 4094.
HWP hwMinMProtectApsSwitchMode	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.15	HWProtectMode	read-create	Indicates the protection modes of the G.8031 Aps protection group of mac-tunnels. oneplusonebidirectional(1): 1 + 1 switchover protection modes on both ends oneplusoneunidirectional(2): 1 + 1 switchover protection modes on a single end onetoone(3): 1:1 protection mode By the default, the 1:1 protection mode is used.
ENA hwMinMProtectProtocolApsEnable	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.16	EnabledStatus	read-create	Indicates that the G.8031 protocol of Aps protection group in the mac-tunnel is enabled. By default, the protocol is disabled.
NUM hwMinMProtectApsFastInterval	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.17	HWApsInterval	read-create	Indicates the configuration of fast sending time interval for each protection group. The time intervals for fast sending of Aps packets described in the G.8031 are as follows: By default, the time interval for fast sending of Aps packets in G.8031 is 3.3 ms. Optional values for sending interval are as follows: ApsInterval3dot3ms(1): indicates a sending interval of 3.3 ms. ApsInterval5ms(3): indicates a sending interval of 5 ms. ApsInterval10ms(3): indicates a sending interval of 10 ms. ApsInterval5ms(4): indicates a sending interval of 15 ms. ApsInterval20ms(5): indicates a sending interval of 20 ms. ApsInterval30ms(6): indicates a sending interval of 30 ms.
I32 hwMinMProtectHoldoffTime	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.18	Integer32	read-create	Indicates the switchover restoration time of Aps protection groups in the mac-tunnel, in 100 ms. It ranges from 0 to 100. By default, the switchover restoration time is not delayed. The value of delay is zero.
ENA hwMinMProtectRevMode	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.19	EnabledStatus	read-create	Indicates the non-restoration protection switchover mode of Aps protection group in mac-tunnels.
I32 hwMinMProtectRevWtrTime	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.20	Integer32	read-create	Indicates the restoration time of restoration protection switchover mode of Aps protection group in mac-tunnels. By default, the switchover mode is restoration. The restoration time is five minutes.
HWS hwMinMProtectSwitchOperation	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.21	HWSwitchOperation	read-create	Indicates the switchover commands for the Aps protection group of mac-tunnels. The priority levels in a descending order are: clear, lock, force and manual. clear(1): clears the lock, force and manual commands, and WTR state on the local end. After the local commands are cleared, the WTR state cannot be entered. lock(2): locks the services on the working tunnel. force(3): forcibly switches the services to the protection tunnel when the protection tunnel is in sound state. manual(4): forcibly switches the services to the protection channel when the working and the protection tunnel are in sound state. null(5):there is not manual commands.
HWP hwMinMProtectProtocol	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.22	HWProtectProtocol	read-create	Indicates the protection protocol of the protection group of mac-tunnels. ProtocolAPS(1): use an APS protocol to enhance the protection switching. ProtocolOAM(2): not using any APS protocol to enhance the protection switching. By the default, the ProtocolOAM is used.
ROW hwMinMProtectRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.2.3.1.1.51	RowStatus	read-create	Indicates the RowStatus. The following three actions are used: active, createAndGo, destroy
hwMinMSIObjects	1.3.6.1.4.1.2011.5.25.133.1.1.3
U32 hwMinMSIIndexNext	1.3.6.1.4.1.2011.5.25.133.1.1.3.1	Unsigned32	read-only	Indicates the index of the next Service Instance. It begins with one.
hwMinMSICfgTable	1.3.6.1.4.1.2011.5.25.133.1.1.3.2		not-accessible	Indicates the configuration table of a service instance.
hwMinMSICfgEntry	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1		not-accessible	Indicates the configuration table entry of a service instance.
U32 hwMinMSIIndex	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.1	Unsigned32	not-accessible	Indicates the Index of Service Instance.It begins with one.
I32 hwMinMSIID	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.11	Integer32	read-create	Indicates the ID of a service instance. It can be any value within 24 bits. By default, the value is null. One ID can be configured to one service instance only.
OCT hwMinMSIName	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.12	OCTET STRING	read-create	Indicates the name of a service instance. It is a character string with a maximum of 31 bytes and a minimum of 1 byte.
HWS hwMinMSIServiceType	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.13	HWServiceType	read-create	Indicates the type of a service instance as follows: p2p: indicates the type of a point-to-point service instance. mp2mp: indicates the type of a multi-point to multi-point service instance. By default, the service type is mp2mp.
T/F hwMinMSIPriorityTrust8021p	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.14	TruthValue	read-create	Indicates that the priority of user packet based on 802.1Q is trusted. By default, no user priority is trusted.
I32 hwMinMSIPriorityValue	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.15	Integer32	read-create	Indicates priority level of a service instance. It is used to set the priority field of I-TAG. By default, no user priority is trusted and the priority is zero. The special value of eight is used to indicate that priority of user is trusted.
NUM hwMinMSIInterfaceType	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.16	HWInterfaceType	read-create	Indicates the interface type of a service instance. transparent: indicates the transparent transmission mode. one-to-one: indicates the one-to-one in the s-tagged mode. bundling: indicates the bundling in the s-tagged mode. By default, the s-tagged bundling mode is used.
HWA hwMinMSIAdminStatus	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.17	HWAdminStatus	read-create	Indicates the administration status of a service instance.
HWO hwMinMSIOperStatus	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.18	HWOperStatus	read-only	Indicates the physical status of a service instance.
ENA hwMinMSIMacLearningEnable	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.19	EnabledStatus	read-create	Disable the MAC learning of a service instance. By default, the MAC learning is enabled. This object applies to the service instance of mp2mp only. It is invalid in the service type of p2p.
HWP hwMinMSIMacLimitAction	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.20	HWProcessBehavior	read-create	Indicates MAC learning restriction of a service instance. After the number of MAC address entries reaches the limit, the system takes the following actions: discard: indicates that packets with new MAC address are discarded. forward: indicates that packets with new MAC address are forwarded, but the address is not added to the MAC address table.
ENA hwMinMSIMacLimitAlarm	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.21	EnabledStatus	read-create	Indicates MAC learning restriction of a service instance. Indicates whether alarm should be sent after the number of MAC address entries reaches the limit as follows: disable: indicates no alarm is sent. enable: indicates alarm is sent in syslog.
I32 hwMinMSIMacLimitMaxinum	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.22	Integer32	read-create	Indicates MAC learning restriction of a service instance. The number of MAC addresses that can be learnt by the current service instance ranges from 0 to 131072. When the number is set to zero, no restriction is imposed on the address learning.
BIT hwMinMSIL2CtrlProProcess	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.23	Bits	read-create	This configuration is unsuitable for the case of port+vlan+cos mapping. Layer 2 control packets of a service instance are handled as follows: By default, all layer 2 control packets are transmitted transparently and all bits are 0; if a bit is 1, it indicates that the packets of this protocol will be discarded. If bit 0 is 1, it indicates that all layer 2 control packets will be discarded. If bit 1 is 1, it indicates that the STP packets will be discarded. If bit 2 is 1, it indicates that the LLAP packets will be discarded. If bit 3 is 1, it indicates that the LACP packets will be discarded. If bit 4 is 1, it indicates that the DOT3AH packets will be discarded. If bit 5 is 1, it indicates that the DOTLAG packets will be discarded.
ENA hwMinMSIUnknownUnicastEnbale	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.24	EnabledStatus	read-create	Indicates how a service instance processes an unknown unicast packet. By default, the service instance is allowed to broadcast the unknown unicast packet. This object applies to the mp2mp service instance only.
ENA hwMinMSIMulticastEnable	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.25	EnabledStatus	read-create	Indicates how a service instance processes an unknown multicast packet. By default, the service instance is allowed to broadcast the unknown multicast packet. This object applies to the mp2mp service instance only.
ENA hwMinMSIBroadcastEnable	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.26	EnabledStatus	read-create	Indicates how a service instance processes a broadcast packet. By default, the service instance is allowed to forward the broadcast packet. This object applies to the mp2mp service instance only.
OCT hwMinMSIDescription	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.27	OCTET STRING	read-create	Indicates descriptive information of a service instance. Its length ranges from 1 to 80 bytes and the first byte cannot be a space.
ENA hwMinMSIStatisticsEnable	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.28	EnabledStatus	read-write	Indicates that the traffic statistics is enabled on a service instance.
ENA hwMinMSIStatisticsReset	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.29	EnabledStatus	read-create	Indicates the reset on traffic statistics of a service instance.
ENA hwMinMSIFcsTransparentEnable	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.30	EnabledStatus	read-create	The forwarded packets need to carry the CRC mark. By default, the forwarded packets do not carry the CRC mark.
I32 hwMinMSIIngressPriorityValue	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.31	Integer32	read-create	Indicates the source priority of a service instance. It is used to set the I-TAG priority field when packets are encapsulated for transmission on the tunnel. The source priority has eight levels that range from 0 to 7. By default, the source priority is copied to the mac-tunnel. When the source priority is set to 8, it indicates that the service instance is not configured with a priority, and the priority does not exist.
T/F hwMinMSIEgressPriorityTrustBTag	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.32	TruthValue	read-create	Indicates that the destination priority of a service instance is copied from the B-TAG priority. It is used to set whether the I-TAG priority is copied from the B-TAG priority when packets reach the end of the tunnel and are decapsulated. By default, the B-TAG priority is not copied to I-TAG.
I32 hwMinMSIIngressDeiValue	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.33	Integer32	read-create	Indicates the source DEI of a service instance. It is used to set the DEI field when packets are encapsulated for transmission on the tunnel. When DEI is true, the value is set to 1. When DEI is false, the value is set to 0. By default, the S-DEI priority is copied to the mac-tunnel. When the value of the DEI is set to 2, it indicates that no DEI is configured on the tunnel.
T/F hwMinMSIEgressDeiTrustBDei	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.34	TruthValue	read-create	Indicates that the destination DEI of a service instance is copied from the B-DEI priority. It is used to set whether the DEI of I-TAG is coped from B-DEI when packets reach the end of the tunnel and are decpasulated. By default, B-DEI is not copied to I-TAG.
ENA hwMinMSIIsolateAll	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.35	EnabledStatus	read-create	Indicates that all the mapping users of a service instance are isolated. By default, the isolation is disabled. This object applies to the service instance of mp2mp only. It is invalid in the service type of p2p.
ROW hwMinMSIRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.3.2.1.51	RowStatus	read-create	Indicates the RowStatus. The following three actions are used: active, createAndGo, destroy
hwMinMSIMappingTable	1.3.6.1.4.1.2011.5.25.133.1.1.3.3		not-accessible	Indicates the configuration table of a service instance user.
hwMinMSIMappingEntry	1.3.6.1.4.1.2011.5.25.133.1.1.3.3.1		not-accessible	Indicates the configuration table entry of a service instance user.
NUM hwMinMSIMappingIfIndex	1.3.6.1.4.1.2011.5.25.133.1.1.3.3.1.1	InterfaceIndexOrZero	not-accessible	The port that is mapped to the current service instance. If the value is 0, it means that port mapping is not supported.
I32 hwMinMSIMappingVlanPriority	1.3.6.1.4.1.2011.5.25.133.1.1.3.3.1.2	Integer32	not-accessible	The priority of a user's packets that are mapped to the current service instance. If the value is 8, it means that the priority mapping is not supported.
VLA hwMinMSIMappingGlobalVlanID	1.3.6.1.4.1.2011.5.25.133.1.1.3.3.1.3	VlanIdOrNone	not-accessible	The global VLAN ID that is mapped to the current service instance. If the value is 0, it means that the global VLAN mapping is not supported.
VLA hwMinMSIMappingVlanListLow	1.3.6.1.4.1.2011.5.25.133.1.1.3.3.1.11	VlanList	read-create	Indicates the VLAN ID starting value of a service instance user.
VLA hwMinMSIMappingVlanListHigh	1.3.6.1.4.1.2011.5.25.133.1.1.3.3.1.12	VlanList	read-create	Indicates the VLAN ID ending value of a service instance user.
ENA hwMinMSIMappingUserIsolate	1.3.6.1.4.1.2011.5.25.133.1.1.3.3.1.13	EnabledStatus	read-create	Indicates that the specified mapping user of a service instance is isolated. By default, the isolation is enabled. This object applies to the service instance of mp2mp only. It is invalid in the service type of p2p
ROW hwMinMSIMappingRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.3.3.1.51	RowStatus	read-create	Indicates the RowStatus. The following three actions are used: active, createAndGo, destroy
hwMinMSIBindMacTnlTable	1.3.6.1.4.1.2011.5.25.133.1.1.3.4		not-accessible	Indicates the mac-tunnel table bound with a service instance.
hwMinMSIBindMacTnlEntry	1.3.6.1.4.1.2011.5.25.133.1.1.3.4.1		not-accessible	Indicates the mac-tunnel table entry bound with a service instance.
U32 hwMinMSIBindMacTnlIndex	1.3.6.1.4.1.2011.5.25.133.1.1.3.4.1.1	Unsigned32	not-accessible	Indicates the index of Mac Tunnel. It begins with one.
ROW hwMinMSIBindMacTnlRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.3.4.1.51	RowStatus	read-create	Indicates the RowStatus. The following three actions are used: active, createAndGo, destroy
hwMinMSIStatisticsTable	1.3.6.1.4.1.2011.5.25.133.1.1.3.5		not-accessible	Indicates the hwMinMSIStatisticsTable of a service instance.
hwMinMSIStatisticsEntry	1.3.6.1.4.1.2011.5.25.133.1.1.3.5.1		not-accessible	Indicates the hwMinMSIStatisticsTable entry of a service instance.
C64 hwMinMSIInPackets	1.3.6.1.4.1.2011.5.25.133.1.1.3.5.1.11	Counter64	read-only	Indicates the number of packets received by a user of the current service instance.
C64 hwMinMSIInBytes	1.3.6.1.4.1.2011.5.25.133.1.1.3.5.1.12	Counter64	read-only	Indicates the number of bytes received by a user of the current service instance.
C64 hwMinMSIOutPackets	1.3.6.1.4.1.2011.5.25.133.1.1.3.5.1.13	Counter64	read-only	Indicates the number of packets sent by a user of the current service instance.
C64 hwMinMSIOutBytes	1.3.6.1.4.1.2011.5.25.133.1.1.3.5.1.14	Counter64	read-only	Indicates the number of bytes sent by a user of the current service instance.
hwMinMSIStaticMacFwdTable	1.3.6.1.4.1.2011.5.25.133.1.1.3.6		not-accessible	Indicates the static MAC forwarding table of a service instance:
hwMinMSIStaticMacFwdEntry	1.3.6.1.4.1.2011.5.25.133.1.1.3.6.1		not-accessible	Indicates the static MAC forwarding table entry of a service instance:
MAC hwMinMSIStaticMacFwdCDMac	1.3.6.1.4.1.2011.5.25.133.1.1.3.6.1.1	MacAddress	not-accessible	Indicates the destination MAC address of a customer.
OCT hwMinMSIStaticMacFwdMacTnlName	1.3.6.1.4.1.2011.5.25.133.1.1.3.6.1.11	OCTET STRING	read-create	Indicates the name of the mac-tunnel. It is a character string with a maximum of 31 bytes and a minimum of 1 byte.
NUM hwMinMSIStaticMacFwdOutgoingIfIndex	1.3.6.1.4.1.2011.5.25.133.1.1.3.6.1.12	InterfaceIndexOrZero	read-create	Indicates a outbound port. The value zero is used to indicate that interface was unknown or none.
VLA hwMinMSIStaticMacFwdVlanID	1.3.6.1.4.1.2011.5.25.133.1.1.3.6.1.13	VlanIdOrNone	read-create	Indicates the downstream vlanid. The special value of zero is used to indicate that no VLAN-ID is present or used.
HWS hwMinMSIStaticMacFwdType	1.3.6.1.4.1.2011.5.25.133.1.1.3.6.1.14	HWStaticMacFwdType	read-create	Indicates the type of the static MAC forwarding table of a service instance: static(1): indicates a static entry. blackhole(2): indicates a blackhole entry.
ROW hwMinMSIStaticMacFwdRowStatus	1.3.6.1.4.1.2011.5.25.133.1.1.3.6.1.51	RowStatus	read-create	Indicates the RowStatus. The following three actions are used: active, createAndGo, destroy.
hwSINameToIndexMappingTable	1.3.6.1.4.1.2011.5.25.133.1.1.3.7		not-accessible	Indicates the name and the index mapping table of a service instance.
hwSINameToIndexMappingEntry	1.3.6.1.4.1.2011.5.25.133.1.1.3.7.1		not-accessible	Indicates the name and the index mapping table entry of a service instance.
OCT hwSIName	1.3.6.1.4.1.2011.5.25.133.1.1.3.7.1.1	OCTET STRING	not-accessible	Indicates the name of a service instance. It is a character string with a maximum of 31 bytes and a minimum of 1 byte.
U32 hwSIIndex	1.3.6.1.4.1.2011.5.25.133.1.1.3.7.1.11	Unsigned32	read-only	Indicates the index of a service instance.It begins with one.
hwMinMNotifications	1.3.6.1.4.1.2011.5.25.133.1.2
NTF hwMinMMacTnlUp	1.3.6.1.4.1.2011.5.25.133.1.2.1			Indicates the Up alarm of the mac-tunnel. This object forms a pair with the following hwMinMMacTnlDown.
NTF hwMinMMacTnlDown	1.3.6.1.4.1.2011.5.25.133.1.2.2			Indicates the Down alarm of the mac-tunnel. This object forms a pair with the previous hwMinMMacTnlUp.
NTF hwMinMSIUp	1.3.6.1.4.1.2011.5.25.133.1.2.3			Indicates the Up alarm of a service instance. This object forms a pair with the following hwMinMSIDown.
NTF hwMinMSIDown	1.3.6.1.4.1.2011.5.25.133.1.2.4			Indicates the Down alarm of a service instance. This object forms a pair with the previous hwMinMSIUp.
NTF hwMinMMacTnlCCFaultAlarm	1.3.6.1.4.1.2011.5.25.133.1.2.5			Indicates an alarm on the connectivity of fault.
NTF hwMinMMacTnlSwitch	1.3.6.1.4.1.2011.5.25.133.1.2.6			Indicates the Aps protection group switchover alarm of the mac-tunnel. This object forms a pair with the following hwMinMMacTnlRevertive. hwMinMMacTnlName: indicates the name of the primary tunnel. hwMinMMacTnlDMac: indicates the destination MAC address of the primary tunnel. hwMinMMacTnlBVlanID: indicates the BVLANID of the primary tunnel. hwMinMProtectMacTnlName: Indicates the name of the backup tunnel. hwMinMProtectSwitchOperation: Indicates the switchover commands for the Aps protection group of mac-tunnels. hwMinMProtectMacTnlBVlanID: indicates the BVLANID of the backup tunnel. hwMinMProtectMacTnlDMac:indicates the destination MAC address of the backup tunnel.
NTF hwMinMMacTnlRevertive	1.3.6.1.4.1.2011.5.25.133.1.2.7			Indicates the Aps protection group switchover alarm of the mac-tunnel. This object forms a pair with the previous hwMinMMacTnlSwitch. hwMinMMacTnlName: indicates the name of the primary tunnel. hwMinMMacTnlDMac: indicates the destination MAC address of the primary tunnel. hwMinMMacTnlBVlanID: indicates the BVLANID of the primary tunnel. hwMinMProtectMacTnlName: Indicates the name of the backup tunnel. hwMinMProtectSwitchOperation: Indicates the switchover commands for the Aps protection group of mac-tunnels. hwMinMProtectMacTnlBVlanID: indicates the BVLANID of the backup tunnel. hwMinMProtectMacTnlDMac:indicates the destination MAC address of the backup tunnel.
NTF hwMinMSIMacLimitNumRaisingThreshold	1.3.6.1.4.1.2011.5.25.133.1.2.8			Indicates the alarm of the mac limiting number beyond the Threshold.
hwMinMConformance	1.3.6.1.4.1.2011.5.25.133.1.3
hwMinMGroups	1.3.6.1.4.1.2011.5.25.133.1.3.1
hwMinMSystemGroup	1.3.6.1.4.1.2011.5.25.133.1.3.1.1			A collection of objects providing the System configuration of the MAC-in-MAC capability.
hwMinMMacTnlCfgGroup	1.3.6.1.4.1.2011.5.25.133.1.3.1.2			A collection of objects providing the configuration of the MAC TUNNEL capability.
hwMinMMacTnlStatisticsGroup	1.3.6.1.4.1.2011.5.25.133.1.3.1.3			A collection of objects providing the Statistics of the Service Instance capability.
hwMinMMacTnlOAMGroup	1.3.6.1.4.1.2011.5.25.133.1.3.1.4			A collection of objects providing the OAM of the MAC TUNNEL capability.
hwMinMMacTnlApsGroup	1.3.6.1.4.1.2011.5.25.133.1.3.1.5			A collection of objects providing the Aps of the MAC TUNNEL capability.
hwMinMSICfgGroup	1.3.6.1.4.1.2011.5.25.133.1.3.1.6			A collection of objects providing the configuration of Service Instance capability.
hwMinMSIStatisticsGroup	1.3.6.1.4.1.2011.5.25.133.1.3.1.7			A collection of objects providing the Statistics of the Service Instance capability.
hwMinMNotificationGroup	1.3.6.1.4.1.2011.5.25.133.1.3.1.8			Collection of notification objects.
hwMinMCompliances	1.3.6.1.4.1.2011.5.25.133.1.3.2			The compliance statement for entities implementing the Huawei MINM MIB

RFC description

Huawei proprietary MIB for managing 802.1ah MAC-in-MAC (provider bridge) network functionality, including backbone VLAN configuration and MAC tunnel settings for provider bridge networks.

Start monitoring Huawei carrier access-network element / ONT (Minimized Network Management) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-MINM-MIB