HUAWEI-ATM-MIB

All MIBs › HUAWEI-ATM-MIB

Organization: Huawei Technologies co.,Ltd.

Last Updated: 2007-10-17

Category: ATM, Vendor: Huawei

Description: Huawei ATM MIB for managing Asynchronous Transfer Mode interfaces, virtual circuits, and traffic parameters on Huawei ATM equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-ATM-MIB?

HUAWEI-ATM-MIB is Huawei's proprietary MIB for managing Asynchronous Transfer Mode interfaces and virtual circuits, specifically covering ATM OC-3/STM-1 and OC-12/STM-4 physical interfaces, IP-over-ATM (IPoA) and IPoEoA encapsulation, PVC service types, OAM F5 loopback testing, VP-limit parameters, and the mapping between peer and local VPI values. It exposes configuration and status objects for these interface types and virtual-circuit/path relationships, layered on top of the underlying physical SONET/SDH-rate interface. Its monitoring value spans both hardware and software status: interface-level detection of OC-3/OC-12 line issues, PVC/VP state and VPI-mapping correctness, and OAM F5 loopback results used to verify end-to-end ATM path health without disrupting traffic. It builds on standard ATM interface conventions (similar in spirit to RFC 2515's ATM-MIB) while being a distinct Huawei implementation. It is deployed on Huawei ATM-capable routers and switches in carrier and enterprise WAN backbones still carrying ATM-encapsulated traffic, and engineers can download the HUAWEI-ATM-MIB file to load into their network management systems.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei ATM-capable routers and switches

Monitoring Examples

An engineer checks the ATM PVC configuration to confirm the mapping between local and peer VPI values matches the intended circuit topology, and validates the VP-limit setting hasn't been exceeded on a heavily provisioned OC-12/STM-4 interface. Running an OAM F5 loopback test on a given PVC and checking its result reveals whether the ATM path is intact end-to-end, useful for isolating an intermittent circuit fault. IPoA/IPoEoA encapsulation settings are checked when IP connectivity over a PVC fails despite the PVC itself being up.

What Can Be Monitored

ATM interface status (OC-3/STM-1, OC-12/STM-4)
PVC/VC configuration and state
VPI mapping (local vs. peer)
OAM F5 loopback test results
VP limit utilization

Imported Objects

From ATM-TC-MIB

AtmVcIdentifier
AtmVpIdentifier

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwAtmMIB	1.3.6.1.4.1.2011.5.25.156			This MIB is mainly used to configure the ATM OC-3/STM-1 and ATM OC-12/STM-4 interface, IPoA, IPoEoA, PVC service type, OAM F5 loopback, parameters of the VP limit, and mapping between the peer VPI and the local VPI.
hwAtmObjects	1.3.6.1.4.1.2011.5.25.156.1
hwAtmTable	1.3.6.1.4.1.2011.5.25.156.1.1		not-accessible	This table is used to configure the parameters of the ATM interface.
hwAtmEntry	1.3.6.1.4.1.2011.5.25.156.1.1.1		not-accessible	This table is used to configure the parameters of the ATM interface.
NUM hwAtmIfIndex	1.3.6.1.4.1.2011.5.25.156.1.1.1.1	InterfaceIndex	not-accessible	Indicates the interface index.
INT hwAtmIfType	1.3.6.1.4.1.2011.5.25.156.1.1.1.11	INTEGER	read-only	Indicates the interface type.
INT hwAtmClock	1.3.6.1.4.1.2011.5.25.156.1.1.1.12	INTEGER	read-write	Master clock: uses the internal clock signal. Slave clock: uses the line clock signal.
INT hwAtmFrameFormat	1.3.6.1.4.1.2011.5.25.156.1.1.1.13	INTEGER	read-write	For the optical interface STM-1/STM-4, the frame format on the ATM interface is SDH; for the OC-3/OC-12 interface, the frame format is SONET. The default frame format is SDH.
T/F hwAtmScramble	1.3.6.1.4.1.2011.5.25.156.1.1.1.14	TruthValue	read-write	By default, the scramble function is enabled. The scramble function takes effect only on payload rather than cell header. true: enables the scramble function. false: disables the scramble function.
INT hwAtmLoopback	1.3.6.1.4.1.2011.5.25.156.1.1.1.15	INTEGER	read-write	Enable the loopback function of the channel. local: enables the local loopback on the interface. remote: enables the remote loopback on the interface. payload: enables the remote payload loopback on the interface. By default, all loopback functions are disabled.
hwAtmMapPvpTable	1.3.6.1.4.1.2011.5.25.156.1.2		not-accessible	This table is used to configure the mapping between the peer VPI and the local VPI.
hwAtmMapPvpEntry	1.3.6.1.4.1.2011.5.25.156.1.2.1		not-accessible	This table is used to configure the mapping between the peer VPI and the local VPI.
NUM hwAtmMapPvpIfIndex	1.3.6.1.4.1.2011.5.25.156.1.2.1.1	InterfaceIndex	not-accessible	Indicates the interface index.
OID hwAtmMapPvpVplVpi	1.3.6.1.4.1.2011.5.25.156.1.2.1.2	AtmVpIdentifier	not-accessible	Indicates the local VPI value. The value is an integer ranging from 0 to 255.
OID hwAtmMapPvpRemoteVplVpi	1.3.6.1.4.1.2011.5.25.156.1.2.1.11	AtmVpIdentifier	read-create	Indicates the peer VPI value. The value is an integer ranging from 0 to 255.
ROW hwAtmMapPvpRowStatus	1.3.6.1.4.1.2011.5.25.156.1.2.1.51	RowStatus	read-create	This variable is used to create or delete an object.
hwAtmMapPvcTable	1.3.6.1.4.1.2011.5.25.156.1.3		not-accessible	This table is used to configure the mapping between the peer VPI/VCI and the local VPI/VCI.
hwAtmMapPvcEntry	1.3.6.1.4.1.2011.5.25.156.1.3.1		not-accessible	This table is used to configure the mapping between the peer VPI/VCI and the local VPI/VCI.
OID hwAtmMapPvcRemoteVclVci	1.3.6.1.4.1.2011.5.25.156.1.3.1.11	AtmVcIdentifier	read-create	Indicates the peer VCI value. VCI is short for Virtual Channel Identifier. The VCI value ranges from 0 to 2047. Generally, the values from 0 to 31 are reserved for specail use.
OID hwAtmMapPvcRemoteVclVpi	1.3.6.1.4.1.2011.5.25.156.1.3.1.12	AtmVpIdentifier	read-create	Indicates the peer VPI value. The value is an integer ranging from 0 to 255.
ROW hwAtmMapPvcRowStatus	1.3.6.1.4.1.2011.5.25.156.1.3.1.51	RowStatus	read-create	This variable is used to create or delete an object.
hwAtmServiceTable	1.3.6.1.4.1.2011.5.25.156.1.4		not-accessible	This table is used to configure the service type and related parameters for the PVC.
hwAtmServiceEntry	1.3.6.1.4.1.2011.5.25.156.1.4.1		not-accessible	This table is used to configure the service type for the PVC.
OCT hwAtmServiceName	1.3.6.1.4.1.2011.5.25.156.1.4.1.1	OCTET STRING	not-accessible	Indicates the name of the service type. The name is a string of 1 to 31 characters.
INT hwAtmServiceType	1.3.6.1.4.1.2011.5.25.156.1.4.1.11	INTEGER	read-create	Set the service type for the PVC as required.
I32 hwAtmServiceOutputPcr	1.3.6.1.4.1.2011.5.25.156.1.4.1.12	Integer32	read-create	Indicates the peak output rate of the ATM cell. When hwPvcServiceTableType is ubr, the peak output rate is 0.
I32 hwAtmServiceOutputScr	1.3.6.1.4.1.2011.5.25.156.1.4.1.13	Integer32	read-create	Indicates the peak output rate of the ATM cell. When hwPvcServiceTableType is cbr or ubr, the peak output rate is 0.
I32 hwAtmServiceOutputMbs	1.3.6.1.4.1.2011.5.25.156.1.4.1.14	Integer32	read-create	Indicates the peak output rate of the ATM cell. When hwPvcServiceTableType is cbr or ubr, the peak output rate is 0.
I32 hwAtmServiceCbrCdvtValue	1.3.6.1.4.1.2011.5.25.156.1.4.1.15	Integer32	read-create	Indicates the limit of the ATM cell delay variation. When hwPvcServiceTableType is cbr, the variable is valid. For other service types, the variable is 0.
I32 hwAtmServiceOutputMcr	1.3.6.1.4.1.2011.5.25.156.1.4.1.16	Integer32	read-create	Indicates the mini width guarantee bit rate of the ATM cell. When hwPvcServiceTableType is ubr, the peak output rate is 0.
ROW hwAtmServiceRowStatus	1.3.6.1.4.1.2011.5.25.156.1.4.1.51	RowStatus	read-create	This variable is used to create or delete an object.
hwAtmPvcServiceTable	1.3.6.1.4.1.2011.5.25.156.1.5		not-accessible	This table is used to configure the service type for the PVC.
hwAtmPvcServiceEntry	1.3.6.1.4.1.2011.5.25.156.1.5.1		not-accessible	This table is used to configure the service type for the PVC.
OCT hwAtmPvcServiceName	1.3.6.1.4.1.2011.5.25.156.1.5.1.11	OCTET STRING	read-create	Indicates the name of the service type. The name is a string of 1 to 31 characters.
INT hwAtmPvcTransmittalDirection	1.3.6.1.4.1.2011.5.25.156.1.5.1.21	INTEGER	read-create	Indicates the input or output tpye of the service type.
ROW hwAtmPvcServiceRowStatus	1.3.6.1.4.1.2011.5.25.156.1.5.1.51	RowStatus	read-create	This variable is used to create or delete an object.
hwAtmIfConfTable	1.3.6.1.4.1.2011.5.25.156.1.11		not-accessible	Indicates the configuration of the ATM interface.
hwAtmIfConfEntry	1.3.6.1.4.1.2011.5.25.156.1.11.1		not-accessible	Indicates the configuration of the ATM interface.
NUM hwAtmIfConfIfIndex	1.3.6.1.4.1.2011.5.25.156.1.11.1.1	InterfaceIndex	not-accessible	Indicates the interface index.
I32 hwAtmIfConfMaxVccs	1.3.6.1.4.1.2011.5.25.156.1.11.1.11	Integer32	read-write	Indicates the maximum number of the PVCs.
I32 hwAtmIfConfOperVccs	1.3.6.1.4.1.2011.5.25.156.1.11.1.12	Integer32	read-only	Indicates the number of the configured PVCs.
INT hwAtmIfConfIntfType	1.3.6.1.4.1.2011.5.25.156.1.11.1.13	INTEGER	read-write	This object indicates the type of the serial interface with the ATM protocol.
hwAtmVplTable	1.3.6.1.4.1.2011.5.25.156.1.12		not-accessible	Indicates the configuration of the ATM PVP.
hwAtmVplEntry	1.3.6.1.4.1.2011.5.25.156.1.12.1		not-accessible	Indicates the configuration of the ATM PVP.
NUM hwAtmVplIfIndex	1.3.6.1.4.1.2011.5.25.156.1.12.1.1	InterfaceIndex	not-accessible	Indicates the interface index.
OID hwAtmVplVpi	1.3.6.1.4.1.2011.5.25.156.1.12.1.2	AtmVpIdentifier	not-accessible	VPI.
ROW hwAtmVplRowStatus	1.3.6.1.4.1.2011.5.25.156.1.12.1.51	RowStatus	read-create	Indicates the status of the row.
hwAtmVclTable	1.3.6.1.4.1.2011.5.25.156.1.13		not-accessible	Indicates the configuration of the ATM PVC.
hwAtmVclEntry	1.3.6.1.4.1.2011.5.25.156.1.13.1		not-accessible	Indicates the configuration of the ATM PVC.
NUM hwAtmVclIfIndex	1.3.6.1.4.1.2011.5.25.156.1.13.1.1	InterfaceIndex	not-accessible	Indicates the interface index.
OID hwAtmVclVpi	1.3.6.1.4.1.2011.5.25.156.1.13.1.2	AtmVpIdentifier	not-accessible	VPI.
OID hwAtmVclVci	1.3.6.1.4.1.2011.5.25.156.1.13.1.3	AtmVcIdentifier	not-accessible	VCI.
OCT hwAtmVclName	1.3.6.1.4.1.2011.5.25.156.1.13.1.11	OCTET STRING	read-create	Indicates the name of the PVC.
INT hwAtmVccAal5EncapsType	1.3.6.1.4.1.2011.5.25.156.1.13.1.12	INTEGER	read-create	Indicates the encapsulation mode of AAL5.
ROW hwAtmVclRowStatus	1.3.6.1.4.1.2011.5.25.156.1.13.1.51	RowStatus	read-create	Indicates the status of the row.
hwAtmPvcIpoaTable	1.3.6.1.4.1.2011.5.25.156.1.14		not-accessible	This table is used to configure the IPoA mapping on the PVC.
hwAtmPvcIpoaEntry	1.3.6.1.4.1.2011.5.25.156.1.14.1		not-accessible	This table is used to configure the IPoA mapping on the PVC.
INT hwAtmPvcIpoaType	1.3.6.1.4.1.2011.5.25.156.1.14.1.3	INTEGER	not-accessible	Indicates the type of the PVC IPoA mapping. ip: sets the peer IP address and mask that are mapped to the PVC. default: configures a mapping with default route attributes. If no mapping of the next hop address of a packet can be found, the packet is sent over the PVC if the PVC is configured with default mapping. inarp: configures InARP on the PVC.
IP hwAtmPvcIpoaIpAddress	1.3.6.1.4.1.2011.5.25.156.1.14.1.4	IpAddress	not-accessible	Indicates the peer IP address mapped to the PVC.
IP hwAtmPvcIpoaIpMask	1.3.6.1.4.1.2011.5.25.156.1.14.1.11	IpAddress	read-create	Indicates the IP address mask. The IP address mask is an optional parameter.
I32 hwAtmPvcIpoaInarpInterval	1.3.6.1.4.1.2011.5.25.156.1.14.1.12	Integer32	read-create	Indicates the interval for sending InARP packets. The parameter is optional. The value ranges from 1 to 600 in seconds. If the type of the PVC IPoA mapping is IP or default, the value is 0. The default value is 1.
T/F hwAtmPvcIpoaBroadcast	1.3.6.1.4.1.2011.5.25.156.1.14.1.13	TruthValue	read-create	If a mapping with this attribute is configured on the PVC, broadcast packets on the interface where the PVC resides will be sent over the PVC.
ROW hwAtmPvcIpoaRowStatus	1.3.6.1.4.1.2011.5.25.156.1.14.1.51	RowStatus	read-create	RowStatus.
hwAtmPvcBridgeTable	1.3.6.1.4.1.2011.5.25.156.1.15		not-accessible	This table is used to configure the IPoEoA mapping and PPPoEoA mapping on the PVC.
hwAtmPvcBridgeEntry	1.3.6.1.4.1.2011.5.25.156.1.15.1		not-accessible	This table is used to configure the IPoEoA mapping and PPPoEoA mapping on the PVC.
NUM hwAtmPvcBridgeDstIfIndex	1.3.6.1.4.1.2011.5.25.156.1.15.1.11	InterfaceIndex	read-create	Indicates the index of the VE interface.
ROW hwAtmPvcBridgeRowStatus	1.3.6.1.4.1.2011.5.25.156.1.15.1.51	RowStatus	read-create	RowStatus.
hwAtmPvcOamLoopbackTable	1.3.6.1.4.1.2011.5.25.156.1.17		not-accessible	This table is used to configure OAM F5 Loopback, enable the sending of OAM F5 Loopback cells, and configure the parameters of the retransmission check or modify the parameters of the retransmission check.
hwAtmPvcOAMLoopbackEntry	1.3.6.1.4.1.2011.5.25.156.1.17.1		not-accessible	This table is used to configure OAM F5 Loopback.
I32 hwAtmPvcOAMLoopbackFrequency	1.3.6.1.4.1.2011.5.25.156.1.17.1.11	Integer32	read-create	Indicates the interval for sending OAM F5 Loopback cells.
I32 hwAtmPvcOAMLoopbackUpCount	1.3.6.1.4.1.2011.5.25.156.1.17.1.12	Integer32	read-create	Indicates the number of continuous OAM F5 Loopback cells that must be received before the PVC turns Up.
I32 hwAtmPvcOAMLoopbackDownCount	1.3.6.1.4.1.2011.5.25.156.1.17.1.13	Integer32	read-create	Indicates the number of continuous OAM F5 Loopback cells that are not received before the PVC turns Down.
I32 hwAtmPvcOAMLoopbackRetryFrequency	1.3.6.1.4.1.2011.5.25.156.1.17.1.14	Integer32	read-create	Indicates the interval for sending cells during OAM F5 Loopback retransmission verification before the PVC status changes.
ROW hwAtmPvcOAMLoopbackRowStatus	1.3.6.1.4.1.2011.5.25.156.1.17.1.51	RowStatus	read-create	RowStatus
hwAtmPvpLimitTable	1.3.6.1.4.1.2011.5.25.156.1.18		not-accessible	This table is used to configure the VP limit. To monitor the VP, configure related VP parameters.
hwAtmPvpLimitEntry	1.3.6.1.4.1.2011.5.25.156.1.18.1		not-accessible	This table is used to configure the VP limit.
NUM hwAtmPvpLimitIfIndex	1.3.6.1.4.1.2011.5.25.156.1.18.1.1	InterfaceIndex	not-accessible	Indicates the interface index.
OID hwAtmPvpLimitVpi	1.3.6.1.4.1.2011.5.25.156.1.18.1.2	AtmVpIdentifier	not-accessible	VPI.
I32 hwAtmPvpLimitPeakRate	1.3.6.1.4.1.2011.5.25.156.1.18.1.11	Integer32	read-create	VCI.
ROW hwAtmPvpLimitRowStatus	1.3.6.1.4.1.2011.5.25.156.1.18.1.51	RowStatus	read-create	RowStatus.
hwAtmConformance	1.3.6.1.4.1.2011.5.25.156.11
hwAtmCompliances	1.3.6.1.4.1.2011.5.25.156.11.1
hwAtmCompliance	1.3.6.1.4.1.2011.5.25.156.11.1.1			The compliance statement for systems supporting the HUAWEI-ATM-MIB.
hwAtmGroups	1.3.6.1.4.1.2011.5.25.156.11.2
hwAtmObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.1			The Atm attribute group.
hwAtmIfConf	1.3.6.1.4.1.2011.5.25.156.11.2.2			Description.
hwAtmVplObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.3			The Atm Pvc Bridge attribute group.
hwAtmVclObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.4			Description.
hwAtmMapPvpObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.5			The Atm Map Pvp attribute group.
hwAtmMapPvcObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.6			The Atm Map Pvc attribute group.
hwAtmServiceObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.7			The Atm Service attribute group.
hwAtmPvcServiceObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.8			The Atm Pvc Service attribute group.
hwAtmPvcIpoaObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.9			The Atm Pvc IPOA attribute group.
hwAtmPvcBridgeObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.10			The Atm Pvl attribute group.
hwAtmPvcOAMLoopbackObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.11			The Port attribute group.
hwAtmPvpLimitObjectGroup	1.3.6.1.4.1.2011.5.25.156.11.2.12			The Port attribute group.

RFC description

Configures ATM OC-3/STM-1 and OC-12/STM-4 interfaces, IPoA services, and VP mapping.

Start monitoring Huawei ATM-capable router or switch (OC-3/OC-12 ATM interfaces) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-ATM-MIB

What Is HUAWEI-ATM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description