All MIBs › ATM-FORUM-ILMI40-MIB
Category: ATM
Description: Implements ATM Forum ILMI 4.0 Integrated Local Management Interface objects for UNI signaling and address discovery.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ATM-FORUM-ILMI40-MIB?
ATM-FORUM-ILMI40-MIB is a vendor-neutral, standards-based MIB defined by the ATM Forum implementing version 4.0 of the Integrated Local Management Interface (ILMI), used across ATM-capable networking equipment for UNI (User-Network Interface) auto-configuration and address discovery. It exposes per-port ATM interface configuration and status objects, including transmission type, media type, addressing, and operational state, rather than being tied to any single vendor's product. Its monitoring value centers on interface/software operational status: atmfPortOperStatus reports whether an ATM port's ILMI link is up or down, which is the primary software-state health indicator this MIB provides, alongside identification data like atmfPortAddress and atmfMyIpNmAddress used for neighbor/address discovery. It is a companion standard to the broader ATM Forum UNI signaling specifications and is commonly deployed alongside the standard ATM-MIB for interface statistics. It is typically found on legacy ATM switches and ATM-attached routers from any vendor implementing ATM UNI, in carrier and enterprise ATM backbone deployments. Engineers implementing or auditing this functionality typically reference the ATM-FORUM-ILMI40-MIB RFC/standard documentation for the authoritative specification.
IPNetwork Monitor allows you to monitor SNMP objects defined in ATM-FORUM-ILMI40-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- vendor-neutral, standards-based MIB, applicable to any ATM-capable switch or router
Monitoring Examples
An administrator would walk the atmfPortTable (indexed by atmfPortIndex) and check atmfPortOperStatus to confirm an ATM UNI link is operational, cross-referencing atmfPortTransmissionType and atmfPortMediaType against the expected physical layer configuration. Discovering that atmfPortAddress or atmfMyIpNmAddress does not match the expected registered address would indicate an ILMI address-registration failure between the ATM switch and its attached device, a common cause of UNI signaling problems.
What Can Be Monitored
- ATM UNI port operational status
- ATM port transmission/media type
- ILMI-registered ATM address
- local ATM interface name/identifier
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| atmf4B5B | 1.3.6.1.4.1.353.1.2.4 | |||
| atmf8B10B | 1.3.6.1.4.1.353.1.2.5 | |||
| ADR atmfAddressAtmAddress | 1.3.6.1.4.1.353.2.6.1.1.2 | AtmAddress | not-accessible | The ATM address which is in effect on the user side of the ATM UNI port. |
| atmfAddressEntry | 1.3.6.1.4.1.353.2.6.1.1 | not-accessible | Information about a single ATM-layer address in effect on the user-side IME. Note that the index variable atmAddressAtmAddress is a variable-length string, and as such the rule for variable-length strings in section 4.1.6 of RFC 1212 applies. | |
| atmfAddressGroup | 1.3.6.1.4.1.353.2.6 | |||
| INT atmfAddressOrgScope | 1.3.6.1.4.1.353.2.6.1.1.4 | INTEGER | read-write | This object indicates the organizational scope for the referenced address. The information of the referenced address shall not be distributed outside the indicated scope. If the user-side IME does not specify a value for the atmfAddressOrgScope object, the network shall set the value of this object to localNetwork(1), if the registered address is an ATM group address, or to global(15), if the registered address is an individual address. Refer to Annex 6.0 of ATM Forum UNI Signalling 4.0 for guidelines regarding the use of organizational scopes. This organization hierarchy may be mapped to ATM network's routing hierarchy such as PNNI's routing level and the mapping shall be configurable in nodes. Use of this object in a public network is for further study. The default values for organizational scope are localNetwork(1) for ATM group addresses, and global(15) for individual addresses. |
| INT atmfAddressPort | 1.3.6.1.4.1.353.2.6.1.1.1 | INTEGER | not-accessible | A unique value which identifies the UNI port for which the ATM address is in effect. The value of 0 has the special meaning of identifying the local UNI. |
| atmfAddressRegistrationAdminEntry | 1.3.6.1.4.1.353.2.11.1.1 | not-accessible | An entry in the table, containing Address Registration administrative information for the ATM Interface. | |
| atmfAddressRegistrationAdminGroup | 1.3.6.1.4.1.353.2.11 | |||
| INT atmfAddressRegistrationAdminIndex | 1.3.6.1.4.1.353.2.11.1.1.1 | INTEGER | read-only | The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received. |
| INT atmfAddressRegistrationAdminStatus | 1.3.6.1.4.1.353.2.11.1.1.2 | INTEGER | read-only | An indication of whether or not Address Registration is supported on this ATM Interface. Supported(1) indicates that this ATM Interface supports address registration. Unsupported(2) indicates that this ATM Interface does not support address registration. |
| atmfAddressRegistrationAdminTable | 1.3.6.1.4.1.353.2.11.1 | not-accessible | A table of Address Registration administrative information for the ATM Interface. | |
| INT atmfAddressStatus | 1.3.6.1.4.1.353.2.6.1.1.3 | INTEGER | read-write | An indication of the validity of the ATM address at the user side of the UNI port. To configure a new address in this table, the user-side IME must set the appropriate instance of this object to the value valid(1). To delete an existing address in this table, the user-side IME must set the appropriate instance of this object to the value invalid(2). If circumstances occur on the network-side IME which cause an address to become invalid, the network-side IME modifies the value of the appropriate instance of this object to invalid(2). Whenever the value of this object for a particular address becomes invalid(2), the conceptual row for that address may be removed from the table at any time, either immediately or subsequently. |
| atmfAddressTable | 1.3.6.1.4.1.353.2.6.1 | not-accessible | A table implemented by the network-side IME, containing the ATM-layer addresses in effect on the user side of the UNI. | |
| INT atmfAtmLayerConfiguredVCCs | 1.3.6.1.4.1.353.2.2.1.1.5 | INTEGER | read-only | The number of permanent VCCs configured for use on this ATM Interface. |
| INT atmfAtmLayerConfiguredVPCs | 1.3.6.1.4.1.353.2.2.1.1.4 | INTEGER | read-only | The number of permanent VPCs configured for use on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), the maximum number of VPCs is set to zero. |
| INT atmfAtmLayerDeviceType | 1.3.6.1.4.1.353.2.2.1.1.10 | INTEGER | read-only | This object determines the type of the ATM device. This object is used in automatic ATM Interface-Type determination procedure such that a correct operational ATM Interface-type can be determined. An ATM End System shall take the value of user(1), and an ATM network node shall take the value of node(2). |
| atmfAtmLayerEntry | 1.3.6.1.4.1.353.2.2.1.1 | not-accessible | An entry in the table, containing information about the ATM layer of an ATM Interface. | |
| atmfAtmLayerGroup | 1.3.6.1.4.1.353.2.2 | |||
| INT atmfAtmLayerIlmiVersion | 1.3.6.1.4.1.353.2.2.1.1.11 | INTEGER | read-only | An indication of the latest version of the ATM Forum ILMI Specification that is supported on this ATM Interface. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. If this object is not present, a version of the ILMI earlier than 4.0 is supported. |
| INT atmfAtmLayerIndex | 1.3.6.1.4.1.353.2.2.1.1.1 | INTEGER | read-only | The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received. |
| INT atmfAtmLayerMaxSvccVpi | 1.3.6.1.4.1.353.2.2.1.1.14 | INTEGER | read-only | The maximum VPI that the signalling stack on the ATM interface is configured to support for allocation to switched virtual channel connections. |
| INT atmfAtmLayerMaxSvpcVpi | 1.3.6.1.4.1.353.2.2.1.1.13 | INTEGER | read-only | The maximum VPI that the signalling stack on the ATM interface is configured to support for allocation to switched virtual path connections. |
| INT atmfAtmLayerMaxVCCs | 1.3.6.1.4.1.353.2.2.1.1.3 | INTEGER | read-only | The maximum number of switched and permanent VCCs supported on this ATM Interface. |
| INT atmfAtmLayerMaxVciBits | 1.3.6.1.4.1.353.2.2.1.1.7 | INTEGER | read-only | The maximum number of active VCI bits on this ATM Interface. |
| INT atmfAtmLayerMaxVPCs | 1.3.6.1.4.1.353.2.2.1.1.2 | INTEGER | read-only | The maximum number of switched and permanent VPCs supported on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), the maximum number of VPCs PNNI may communicate over is set to zero. |
| INT atmfAtmLayerMaxVpiBits | 1.3.6.1.4.1.353.2.2.1.1.6 | INTEGER | read-only | The maximum number of active VPI bits on this ATM Interface. For virtual interfaces (i.e. Virtual Path Connections used by PNNI), this value has no meaning and is set to zero. |
| INT atmfAtmLayerMinSvccVci | 1.3.6.1.4.1.353.2.2.1.1.15 | INTEGER | read-only | This is the minimum VCI value that the signalling stack is configured to support for allocation to switched virtual channel connections. The same value applies to all SVCC VPI values for which the signalling stack is configured. |
| INT atmfAtmLayerNniSigVersion | 1.3.6.1.4.1.353.2.2.1.1.12 | INTEGER | read-only | An indication of the latest version of the ATM Forum PNNI Signalling Specification that is supported on this ATM Interface. Note that the PNNI routing version is not determined through ILMI. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. |
| atmfAtmLayerTable | 1.3.6.1.4.1.353.2.2.1 | not-accessible | A table of ATM layer status and parameter information for the ATM Interface. | |
| INT atmfAtmLayerUniType | 1.3.6.1.4.1.353.2.2.1.1.8 | INTEGER | read-only | The type of the ATM device, either public or private. |
| INT atmfAtmLayerUniVersion | 1.3.6.1.4.1.353.2.2.1.1.9 | INTEGER | read-only | An indication of the latest version of the ATM Forum UNI Signalling Specification that is supported on this ATM Interface. If this value is not present, a version of the UNI earlier than 3.1 is supported. If the peer IME's value of this object is the same as, or later than the local IME's value, then the version corresponding to the local IME's value should be attempted. Otherwise, if the peer IME's value of this object is earlier, and supported locally, then the local IME should attempt the version corresponding to the peer IME's value. Otherwise, compatibility of the two IMEs cannot be assumed. |
| CTR atmfAtmStatsDroppedReceivedCells | 1.3.6.1.4.1.353.2.3.1.1.3 | Counter | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. |
| atmfAtmStatsEntry | 1.3.6.1.4.1.353.2.3.1.1 | not-accessible | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. | |
| atmfAtmStatsGroup | 1.3.6.1.4.1.353.2.3 | |||
| INT atmfAtmStatsIndex | 1.3.6.1.4.1.353.2.3.1.1.1 | INTEGER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. |
| CTR atmfAtmStatsReceivedCells | 1.3.6.1.4.1.353.2.3.1.1.2 | Counter | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. |
| atmfAtmStatsTable | 1.3.6.1.4.1.353.2.3.1 | not-accessible | This group is deprecated and should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. | |
| CTR atmfAtmStatsTransmittedCells | 1.3.6.1.4.1.353.2.3.1.1.4 | Counter | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. |
| atmfClpNoTaggingMcr | 1.3.6.1.4.1.353.1.4.9 | |||
| atmfClpNoTaggingNoScr | 1.3.6.1.4.1.353.1.4.4 | |||
| atmfClpNoTaggingScr | 1.3.6.1.4.1.353.1.4.7 | |||
| atmfClpTaggingNoScr | 1.3.6.1.4.1.353.1.4.5 | |||
| atmfClpTaggingScr | 1.3.6.1.4.1.353.1.4.8 | |||
| atmfDs3 | 1.3.6.1.4.1.353.1.2.3 | |||
| atmfE1 | 1.3.6.1.4.1.353.1.2.9 | |||
| atmfE3 | 1.3.6.1.4.1.353.1.2.7 | |||
| atmfMediaCoaxCable | 1.3.6.1.4.1.353.1.3.2 | |||
| atmfMediaMultiMode | 1.3.6.1.4.1.353.1.3.4 | |||
| atmfMediaSingleMode | 1.3.6.1.4.1.353.1.3.3 | |||
| atmfMediaStp | 1.3.6.1.4.1.353.1.3.5 | |||
| atmfMediaTypes | 1.3.6.1.4.1.353.1.3 | |||
| atmfMediaUnknownType | 1.3.6.1.4.1.353.1.3.1 | |||
| atmfMediaUtp | 1.3.6.1.4.1.353.1.3.6 | |||
| IP atmfMyIpNmAddress | 1.3.6.1.4.1.353.2.1.2 | IpAddress | read-only | An IP Address to which a Network Management Station can send Network Management protocol messages, e.g. SNMP messages to UDP port 161, in order to access network management information concerning the operation of the ATM device local to this IME. If this object is supported, but the Network Management Agent has not been configured with an IP Address, the IME should return 0.0.0.0. |
| ADR atmfMyOsiNmNsapAddress | 1.3.6.1.4.1.353.2.1.3 | ClnpAddress | read-only | An NSAP Address to which a Network Management Station can send Network Management protocol messages in order to access network management information concerning the operation of the ATM device local to this IME. If this object is supported, but the Network Management Agent has not been configured with an NSAP Address, the IME should return 0.0.0.0 |
| OCT atmfMySystemIdentifier | 1.3.6.1.4.1.353.2.1.4 | OCTET STRING | read-only | A 48 bit identifier, taken from the IEEE universally administered MAC address space, which uniquely identifies the ATM device local to this IME. |
| atmfNetPrefixGroup | 1.3.6.1.4.1.353.2.7 | |||
| atmfNoClpNoScr | 1.3.6.1.4.1.353.1.4.3 | |||
| atmfNoClpScr | 1.3.6.1.4.1.353.1.4.6 | |||
| atmfNoDescriptor | 1.3.6.1.4.1.353.1.4.1 | |||
| atmForum | 1.3.6.1.4.1.353 | |||
| atmForumAdmin | 1.3.6.1.4.1.353.1 | |||
| atmForumUni | 1.3.6.1.4.1.353.2 | |||
| atmfPeakRate | 1.3.6.1.4.1.353.1.4.2 | |||
| atmfPhysicalGroup | 1.3.6.1.4.1.353.2.1 | |||
| ADR atmfPortAddress | 1.3.6.1.4.1.353.2.1.1.1.2 | AtmAddress | read-only | This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification. The Address Group, defined in theAddress Registration MIB should be used instead. |
| atmfPortEntry | 1.3.6.1.4.1.353.2.1.1.1 | not-accessible | An entry in the table, containing information about the physical layer of an ATM Interface. | |
| INT atmfPortIndex | 1.3.6.1.4.1.353.2.1.1.1.1 | INTEGER | read-only | The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received. |
| OID atmfPortMediaType | 1.3.6.1.4.1.353.2.1.1.1.4 | OBJECT IDENTIFIER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead. |
| INT atmfPortMyIfIdentifier | 1.3.6.1.4.1.353.2.1.1.1.8 | INTEGER | read-only | A unique value for each ATM interface. The scheme used to number the ATM interfaces on an ATM device is implementation specific. One way to generate this value is to use the ifIndex that an SNMP manager would use to identify the port. This interface must be uniquely numbered on this system to distinguish parallel links with a neighboring system. |
| STR atmfPortMyIfName | 1.3.6.1.4.1.353.2.1.1.1.7 | DisplayString | read-only | A textual name of this interface. If this system is manageable through SNMP, and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. This interface must be uniquely named on this system to distinguish parallel links with a neighboring system. If this interface does not have a textual name, the value of this object is a zero length string. |
| INT atmfPortOperStatus | 1.3.6.1.4.1.353.2.1.1.1.5 | INTEGER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead. |
| OID atmfPortSpecific | 1.3.6.1.4.1.353.2.1.1.1.6 | OBJECT IDENTIFIER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead. |
| atmfPortTable | 1.3.6.1.4.1.353.2.1.1 | not-accessible | A table of physical layer status and parameter information for the ATM Interface's physical interface. | |
| OID atmfPortTransmissionType | 1.3.6.1.4.1.353.2.1.1.1.3 | OBJECT IDENTIFIER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead. |
| atmfSonetSTS12c | 1.3.6.1.4.1.353.1.2.6 | |||
| atmfSonetSTS3c | 1.3.6.1.4.1.353.1.2.2 | |||
| INT atmfSrvcRegAddressIndex | 1.3.6.1.4.1.353.2.8.1.1.4 | INTEGER | not-accessible | An arbitrary integer to differentiate multiple rows containing different ATM addresses for the same service on the same port. |
| atmfSrvcRegAns | 1.3.6.1.4.1.353.1.5.2 | |||
| ADR atmfSrvcRegATMAddress | 1.3.6.1.4.1.353.2.8.1.1.3 | AtmAddress | read-only | This is the full address of the service. The user-side IME may use this address to establish a connection with the service. |
| atmfSrvcRegEntry | 1.3.6.1.4.1.353.2.8.1.1 | not-accessible | Information about a single service provider that is available to the user-side IME. | |
| atmfSrvcRegistryGroup | 1.3.6.1.4.1.353.2.8 | |||
| atmfSrvcRegLecs | 1.3.6.1.4.1.353.1.5.1 | |||
| OCT atmfSrvcRegParm1 | 1.3.6.1.4.1.353.2.8.1.1.5 | OCTET STRING | read-only | An octet string whose size and meaning is determined by the value of atmfSrvcRegServiceID. |
| INT atmfSrvcRegPort | 1.3.6.1.4.1.353.2.8.1.1.1 | INTEGER | not-accessible | The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received. |
| OID atmfSrvcRegServiceID | 1.3.6.1.4.1.353.2.8.1.1.2 | OBJECT IDENTIFIER | not-accessible | This is the service identifier which uniquely identifies the type of service at the address provided in the table. |
| atmfSrvcRegTable | 1.3.6.1.4.1.353.2.8.1 | not-accessible | The table implemented by the IME on the network side of the ATM UNI port contains all of the services that are available to the user-side IME indexed by service identifier. | |
| atmfSrvcRegTypes | 1.3.6.1.4.1.353.1.5 | |||
| atmfT1 | 1.3.6.1.4.1.353.1.2.8 | |||
| atmfTrafficDescrTypes | 1.3.6.1.4.1.353.1.4 | |||
| atmfTransmissionTypes | 1.3.6.1.4.1.353.1.2 | |||
| atmfUnknownType | 1.3.6.1.4.1.353.1.2.1 | |||
| atmfVccAbrEntry | 1.3.6.1.4.1.353.2.10.1.1 | not-accessible | An entry in the table, containing information about a particular ABR virtual channel connection. | |
| atmfVccAbrGroup | 1.3.6.1.4.1.353.2.10 | |||
| INT atmfVccAbrPortIndex | 1.3.6.1.4.1.353.2.10.1.1.1 | INTEGER | read-only | The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received. |
| atmfVccAbrTable | 1.3.6.1.4.1.353.2.10.1 | not-accessible | A table of operational parameters related to the ABR virtual channel connections which cross this ATM Interface. There is one entry in this table for each ABR virtual channel connection. Each virtual channel connection represented in this table must also be represented by an entry in the atmfVccTable. | |
| INT atmfVccAbrTransmitAdtf | 1.3.6.1.4.1.353.2.10.1.1.10 | INTEGER | read-only | ACR Decrease Time Factor: Time permitted between sending RM-cells, before the allowed rate (ACR) is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 milliseconds. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds). |
| INT atmfVccAbrTransmitCdf | 1.3.6.1.4.1.353.2.10.1.1.7 | INTEGER | read-only | Cutoff Decrease Factor: This field controls the rate decrease associated with lost or delayed backward RM cells. Larger values result in faster rate decrease. The default value is cdfOneOver16(4). |
| INT atmfVccAbrTransmitCrm | 1.3.6.1.4.1.353.2.10.1.1.11 | INTEGER | read-only | RM Cells Before Cutoff: Limits the number of forward RM-cells which may be sent in the absence of received backward RM-cells. |
| INT atmfVccAbrTransmitIcr | 1.3.6.1.4.1.353.2.10.1.1.4 | INTEGER | read-only | Initial Cell Rate: This is the rate at which the source starts, both initially and after an idle period. The unit is cells per second. The value must not be larger than PCR, and is usually lower. |
| INT atmfVccAbrTransmitNrm | 1.3.6.1.4.1.353.2.10.1.1.5 | INTEGER | read-only | The maximum number of data cells a source may send for each forward RM-cell. The default value is nrm32(5). |
| INT atmfVccAbrTransmitRdf | 1.3.6.1.4.1.353.2.10.1.1.9 | INTEGER | read-only | Rate Decrease Factor: Controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12). |
| INT atmfVccAbrTransmitRif | 1.3.6.1.4.1.353.2.10.1.1.8 | INTEGER | read-only | Rate Increment Factor: Controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12). |
| INT atmfVccAbrTransmitTrm | 1.3.6.1.4.1.353.2.10.1.1.6 | INTEGER | read-only | Upper bound on the time between forward RM-cells for an active source (in milliseconds). The default value is trm100(8). |
| INT atmfVccAbrVci | 1.3.6.1.4.1.353.2.10.1.1.3 | INTEGER | read-only | The VCI value of this ABR Virtual Channel Connection at the local ATM Interface. |
| INT atmfVccAbrVpi | 1.3.6.1.4.1.353.2.10.1.1.2 | INTEGER | read-only | The VPI value of this ABR Virtual Channel Connection at the local ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), this value has no meaning and is set to zero |
| T/F atmfVccBestEffortIndicator | 1.3.6.1.4.1.353.2.5.1.1.20 | TruthValue | read-only | The object is examined when atmfVccTransmitTrafficDescriptorType or atmfVccReceiveTrafficDescriptorType for the associated connection is equal to atmfNoClpNoScr. If this object is set to false(2), the network is requested to apply the CBR.1 conformance definition. If this object is set to true(1), the network is requested to apply the UBR.1 conformance definition. |
| NTF atmfVccChange | 1.3.6.1.4.1.353.0.2 | An atmfVccChange trap indicates that a permanent VCC has been added or deleted at this ATM Interface or that the attributes of an existing VCC have been modified.. The variables included in the trap identify the VCI and VPI values of the reconfigured VCC at this ATM Interface. | ||
| atmfVccEntry | 1.3.6.1.4.1.353.2.5.1.1 | not-accessible | An entry in the table, containing information about a particular virtual channel connection. | |
| atmfVccGroup | 1.3.6.1.4.1.353.2.5 | |||
| INT atmfVccOperStatus | 1.3.6.1.4.1.353.2.5.1.1.4 | INTEGER | read-only | The present actual operational status of the VCC. A value of end2endUp(2) or end2endUp(3) is used if the end to end status is known. If only local status is known a value of localUpEnd2endUnknown(4) or localDown(5) is used. |
| INT atmfVccPortIndex | 1.3.6.1.4.1.353.2.5.1.1.1 | INTEGER | read-only | The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received. |
| INT atmfVccQoSCategory | 1.3.6.1.4.1.353.2.5.1.1.17 | INTEGER | read-only | This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification. |
| T/F atmfVccReceiveFrameDiscard | 1.3.6.1.4.1.353.2.5.1.1.22 | TruthValue | read-only | If set to true(1), this object indicates that the network is requested to treat data for this connection (in the receive direction) as frames (e.g. AAL5 CPCS_PDU's) rather than as individual cells. While the precise implementation is network-specific, this treatment may for example involve discarding entire frames during congestion, rather than a few cells from many frames. The default value is false(2). |
| INT atmfVccReceiveQoSClass | 1.3.6.1.4.1.353.2.5.1.1.19 | INTEGER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. |
| INT atmfVccReceiveTrafficDescriptorParam1 | 1.3.6.1.4.1.353.2.5.1.1.12 | INTEGER | read-only | The first parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType. |
| INT atmfVccReceiveTrafficDescriptorParam2 | 1.3.6.1.4.1.353.2.5.1.1.13 | INTEGER | read-only | The second parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType. |
| INT atmfVccReceiveTrafficDescriptorParam3 | 1.3.6.1.4.1.353.2.5.1.1.14 | INTEGER | read-only | The third parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType. |
| INT atmfVccReceiveTrafficDescriptorParam4 | 1.3.6.1.4.1.353.2.5.1.1.15 | INTEGER | read-only | The fourth parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType. |
| INT atmfVccReceiveTrafficDescriptorParam5 | 1.3.6.1.4.1.353.2.5.1.1.16 | INTEGER | read-only | The fifth parameter of the receive parameter vector for this VCC, used according to the value of atmfVccReceiveTrafficDescriptorType. |
| OID atmfVccReceiveTrafficDescriptorType | 1.3.6.1.4.1.353.2.5.1.1.11 | OBJECT IDENTIFIER | read-only | The type of traffic management, applicable to the traffic in the receive direction of this VCC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVccReceiveTrafficDescriptorParam1, atmfVccReceiveTrafficDescriptorParam2, atmfVccReceiveTrafficDescriptorParam3, atmfVccReceiveTrafficDescriptorParam4, and atmfVccReceiveTrafficDescriptorParam5. |
| ATM atmfVccServiceCategory | 1.3.6.1.4.1.353.2.5.1.1.23 | AtmServiceCategory | read-only | The service category of this virtual channel connection. |
| atmfVccTable | 1.3.6.1.4.1.353.2.5.1 | not-accessible | A table of status and parameter information on the virtual channel connections which are visible at this ATM Interface. There is one entry in this table for each permanent virtual channel connection, including reserved VCCs that are supported; e.g., signalling, OAM flows, and ILMI, but not unassigned cells. | |
| T/F atmfVccTransmitFrameDiscard | 1.3.6.1.4.1.353.2.5.1.1.21 | TruthValue | read-only | If set to true(1), this object indicates that the network is requested to treat data for this connection (in the transmit direction) as frames (e.g. AAL5 CPCS_PDU's) rather than as individual cells. While the precise implementation is network-specific, this treatment may for example involve discarding entire frames during congestion, rather than a few cells from many frames. The default value is false(2). |
| INT atmfVccTransmitQoSClass | 1.3.6.1.4.1.353.2.5.1.1.18 | INTEGER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. |
| INT atmfVccTransmitTrafficDescriptorParam1 | 1.3.6.1.4.1.353.2.5.1.1.6 | INTEGER | read-only | The first parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType. |
| INT atmfVccTransmitTrafficDescriptorParam2 | 1.3.6.1.4.1.353.2.5.1.1.7 | INTEGER | read-only | The second parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType. |
| INT atmfVccTransmitTrafficDescriptorParam3 | 1.3.6.1.4.1.353.2.5.1.1.8 | INTEGER | read-only | The third parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType. |
| INT atmfVccTransmitTrafficDescriptorParam4 | 1.3.6.1.4.1.353.2.5.1.1.9 | INTEGER | read-only | The fourth parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType. |
| INT atmfVccTransmitTrafficDescriptorParam5 | 1.3.6.1.4.1.353.2.5.1.1.10 | INTEGER | read-only | The fifth parameter of the transmit parameter vector for this VCC, used according to the value of atmfVccTransmitTrafficDescriptorType. |
| OID atmfVccTransmitTrafficDescriptorType | 1.3.6.1.4.1.353.2.5.1.1.5 | OBJECT IDENTIFIER | read-only | The type of traffic management, applicable to the transmit direction of this VCC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVccTransmitTrafficDescriptorParam1, atmfVccTransmitTrafficDescriptorParam2, atmfVccTransmitTrafficDescriptorParam3, atmfVccTransmitTrafficDescriptorParam4, and atmfVccTransmitTrafficDescriptorParam5. |
| INT atmfVccVci | 1.3.6.1.4.1.353.2.5.1.1.3 | INTEGER | read-only | The VCI value of this Virtual Channel Connection at the local ATM Interface. |
| INT atmfVccVpi | 1.3.6.1.4.1.353.2.5.1.1.2 | INTEGER | read-only | The VPI value of this Virtual Channel Connection at the local ATM Interface. For virtual interfaces (i.e. Virtual Path Connections), this value has no meaning and is set to zero |
| atmfVpcAbrEntry | 1.3.6.1.4.1.353.2.9.1.1 | not-accessible | An entry in the table, containing information about a particular ABR virtual path connection. | |
| atmfVpcAbrGroup | 1.3.6.1.4.1.353.2.9 | |||
| INT atmfVpcAbrPortIndex | 1.3.6.1.4.1.353.2.9.1.1.1 | INTEGER | read-only | The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received. |
| atmfVpcAbrTable | 1.3.6.1.4.1.353.2.9.1 | not-accessible | A table of operational parameters related to the ABR virtual path connections which cross this ATM Interface. There is one entry in this table for each ABR virtual path connection. Each virtual path connection represented in this table must also be represented by an entry in the atmfVpcTable. | |
| INT atmfVpcAbrTransmitAdtf | 1.3.6.1.4.1.353.2.9.1.1.9 | INTEGER | read-only | ACR Decrease Time Factor: Time permitted between sending RM-cells, before the allowed rate (ACR) is decreased to ICR. Range is 10 ms to 10.23 seconds. The unit is 10 milliseconds. For example, the default value of 50 corresponds to a time factor of 500 ms. Larger values allow a source to retain its current rate longer, during periods of relative inactivity. The default is 50 (0.5 seconds). |
| INT atmfVpcAbrTransmitCdf | 1.3.6.1.4.1.353.2.9.1.1.6 | INTEGER | read-only | Cutoff Decrease Factor: This field controls the rate decrease associated with lost or delayed backward RM cells. Larger values result in faster rate decrease. The default value is cdfOneOver16(4). |
| INT atmfVpcAbrTransmitCrm | 1.3.6.1.4.1.353.2.9.1.1.10 | INTEGER | read-only | RM Cells Before Cutoff: Limits the number of forward RM-cells which may be sent in the absence of received backward RM-cells. |
| INT atmfVpcAbrTransmitIcr | 1.3.6.1.4.1.353.2.9.1.1.3 | INTEGER | read-only | Initial Cell Rate: This is the rate at which the source starts, both initially and after an idle period. The unit is cells per second. The value must not be larger than PCR, and is usually lower. |
| INT atmfVpcAbrTransmitNrm | 1.3.6.1.4.1.353.2.9.1.1.4 | INTEGER | read-only | The maximum number of data cells a source may send for each forward RM-cell. The default value is nrm32(5). |
| INT atmfVpcAbrTransmitRdf | 1.3.6.1.4.1.353.2.9.1.1.8 | INTEGER | read-only | Rate Decrease Factor: Controls the rate decrease which occurs when backward RM-cells with CI=1, are received. Larger values lead to faster rate decrease. The default value is rdfOneOver16(12). |
| INT atmfVpcAbrTransmitRif | 1.3.6.1.4.1.353.2.9.1.1.7 | INTEGER | read-only | Rate Increment Factor: Controls the rate at which the rate increases, when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase. The default value is rifOneOver16(12). |
| INT atmfVpcAbrTransmitTrm | 1.3.6.1.4.1.353.2.9.1.1.5 | INTEGER | read-only | Upper bound on the time between forward RM-cells for an active source (in milliseconds). The default value is trm100(8). |
| INT atmfVpcAbrVpi | 1.3.6.1.4.1.353.2.9.1.1.2 | INTEGER | read-only | The VPI value of this ABR Virtual Path Connection at the local ATM Interface. |
| T/F atmfVpcBestEffortIndicator | 1.3.6.1.4.1.353.2.4.1.1.19 | TruthValue | read-only | The object is examined when atmfVpcTransmitTrafficDescriptorType or atmfVpcReceiveTrafficDescriptorType for the associated connection is equal to atmfNoClpNoScr. If this object is set to false(2), the network is requested to apply the CBR.1 conformance definition. If this object is set to true(1), the network is requested to apply the UBR.1 conformance definition. |
| NTF atmfVpcChange | 1.3.6.1.4.1.353.0.1 | An atmfVpcChange trap indicates that a permanent VPC has been added or deleted at this ATM Interface or that the attributes of an existing VPC have been modified. The variables included in the trap identify the VPI value of the reconfigured VPC at this ATM Interface. | ||
| atmfVpcEntry | 1.3.6.1.4.1.353.2.4.1.1 | not-accessible | An entry in the table, containing information about a particular virtual path connection. | |
| atmfVpcGroup | 1.3.6.1.4.1.353.2.4 | |||
| INT atmfVpcOperStatus | 1.3.6.1.4.1.353.2.4.1.1.3 | INTEGER | read-only | The present actual operational status of the VPC. A value of end2endUp(2) or end2endDown(3) would be used if the end-to-end status is known. If only local status information is available, a value of localUpEnd2endUnknown(4) or localDown(5) would be used. |
| INT atmfVpcPortIndex | 1.3.6.1.4.1.353.2.4.1.1.1 | INTEGER | read-only | The value of 0 which has the special meaning of identifying the ATM Interface over which this message was received. |
| INT atmfVpcQoSCategory | 1.3.6.1.4.1.353.2.4.1.1.16 | INTEGER | read-only | This object should not be implemented except as required for backward compatibility with version 2.0 of the UNI specification. |
| INT atmfVpcReceiveQoSClass | 1.3.6.1.4.1.353.2.4.1.1.18 | INTEGER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. |
| INT atmfVpcReceiveTrafficDescriptorParam1 | 1.3.6.1.4.1.353.2.4.1.1.11 | INTEGER | read-only | The first parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType. |
| INT atmfVpcReceiveTrafficDescriptorParam2 | 1.3.6.1.4.1.353.2.4.1.1.12 | INTEGER | read-only | The second parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType. |
| INT atmfVpcReceiveTrafficDescriptorParam3 | 1.3.6.1.4.1.353.2.4.1.1.13 | INTEGER | read-only | The third parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType. |
| INT atmfVpcReceiveTrafficDescriptorParam4 | 1.3.6.1.4.1.353.2.4.1.1.14 | INTEGER | read-only | The fourth parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType. |
| INT atmfVpcReceiveTrafficDescriptorParam5 | 1.3.6.1.4.1.353.2.4.1.1.15 | INTEGER | read-only | The fifth parameter of the receive parameter vector for this VPC, used according to the value of atmfVpcReceiveTrafficDescriptorType. |
| OID atmfVpcReceiveTrafficDescriptorType | 1.3.6.1.4.1.353.2.4.1.1.10 | OBJECT IDENTIFIER | read-only | The type of traffic management, applicable to the traffic in the receive direction of this VPC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVpcReceiveTrafficDescriptorParam1, atmfVpcReceiveTrafficDescriptorParam2, atmfVpcReceiveTrafficDescriptorParam3, atmfVpcReceiveTrafficDescriptorParam4, and atmfVpcReceiveTrafficDescriptorParam5. |
| ATM atmfVpcServiceCategory | 1.3.6.1.4.1.353.2.4.1.1.20 | AtmServiceCategory | read-only | The service category of this virtual path connection. |
| atmfVpcTable | 1.3.6.1.4.1.353.2.4.1 | not-accessible | A table of status and parameter information on the virtual path connections which cross this ATM Interface. There is one entry in this table for each permanent virtual path connection. | |
| INT atmfVpcTransmitQoSClass | 1.3.6.1.4.1.353.2.4.1.1.17 | INTEGER | read-only | This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. |
| INT atmfVpcTransmitTrafficDescriptorParam1 | 1.3.6.1.4.1.353.2.4.1.1.5 | INTEGER | read-only | The first parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType. |
| INT atmfVpcTransmitTrafficDescriptorParam2 | 1.3.6.1.4.1.353.2.4.1.1.6 | INTEGER | read-only | The second parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType. |
| INT atmfVpcTransmitTrafficDescriptorParam3 | 1.3.6.1.4.1.353.2.4.1.1.7 | INTEGER | read-only | The third parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType. |
| INT atmfVpcTransmitTrafficDescriptorParam4 | 1.3.6.1.4.1.353.2.4.1.1.8 | INTEGER | read-only | The fourth parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType. |
| INT atmfVpcTransmitTrafficDescriptorParam5 | 1.3.6.1.4.1.353.2.4.1.1.9 | INTEGER | read-only | The fifth parameter of the transmit parameter vector for this VPC, used according to the value of atmfVpcTransmitTrafficDescriptorType. |
| OID atmfVpcTransmitTrafficDescriptorType | 1.3.6.1.4.1.353.2.4.1.1.4 | OBJECT IDENTIFIER | read-only | The type of traffic management, applicable to the transmit direction of this VPC. The type may indicate none, or a type with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmfVpcTransmitTrafficDescriptorParam1, atmfVpcTransmitTrafficDescriptorParam2, atmfVpcTransmitTrafficDescriptorParam3, atmfVpcTransmitTrafficDescriptorParam4, and atmfVpcTransmitTrafficDescriptorParam5. |
| INT atmfVpcVpi | 1.3.6.1.4.1.353.2.4.1.1.2 | INTEGER | read-only | The VPI value of this Virtual Path Connection at the local ATM Interface. |
RFC description
Implements ATM Forum ILMI 4.0 management information base for ATM device configuration and monitoring.
Start monitoring ATM-capable switches/routers (ILMI 4.0) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.