HUAWEI-ADSL2-LINE-MIB

All MIBs › HUAWEI-ADSL2-LINE-MIB

Organization: XDSL Group

Last Updated: 2006-09-01

Description: HUAWEI-ADSL2-LINE-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-ADSL2-LINE-MIB?

HUAWEI-ADSL2-LINE-MIB is Huawei's implementation of the standards-based ADSL2/ADSL2+ line management MIB, built on the IETF specification (extending RFC 2662 concepts) for managing Asymmetric Digital Subscriber Line interfaces per the ITU-T G.992.1/G.992.2 and related ADSL2 standards. Although no sample objects were provided, a MIB of this type would characteristically expose per-line configuration and performance data such as line rate, noise margin, attenuation, training/link state, and Embedded Operations Channel (EOC) parameters for each DSL port. Its primary use is monitoring the physical/software line status of DSL interfaces -- line up/down state, sync rate, signal-to-noise margin, and error counters -- which are the standard indicators of DSL circuit health used by carriers to detect degraded or failed subscriber lines. It is explicitly dependent on the IETF ADSL/ADSL2 MIB framework (RFC 2662 and successors) which it extends for ADSL2/ADSL2+ line types. It is typically deployed on Huawei DSLAM/MSAN access equipment used by broadband service providers to manage last-mile ADSL2/ADSL2+ subscriber circuits. Engineers can download the HUAWEI-ADSL2-LINE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-ADSL2-LINE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei DSLAM/MSAN broadband access equipment
vendor implementation of a standards-based (IETF) ADSL2/ADSL2+ line MIB

Monitoring Examples

No sample objects were supplied for this MIB, so specific object or table names cannot be cited; based on its stated ADSL2/ADSL2+ line-management purpose, a realistic (but unconfirmed) monitoring scenario would involve polling per-line rate, noise margin, and link-state objects on a DSLAM port to detect a subscriber line that has dropped sync or shows rising error rates, but this cannot be grounded in the provided sample data.

What Can Be Monitored

DSL line up/down/link state
line sync rate
signal-to-noise margin
line attenuation
EOC channel parameters

Imported Objects

From HC-PerfHist-TC-MIB

HCPerfIntervalThreshold
HCPerfTimeElapsed

From HUAWEI-ADSL2-LINE-TC-MIB

Adsl2BitSwap
Adsl2CfgMode
Adsl2ChAtmStatus
Adsl2ChPtmStatus
Adsl2ConfPmsForce
Adsl2Direction
Adsl2InitResult
Adsl2LConfProfPmMode
Adsl2LastTransmittedState
Adsl2LdsfResult
Adsl2LineLdsf
Adsl2LineStatus
Adsl2MaxBer
Adsl2OperationModes
Adsl2PowerMngState
Adsl2PsdMaskDs
Adsl2PsdMaskUs
Adsl2RaMode
Adsl2RfiDs
Adsl2ScMaskDs
Adsl2ScMaskUs
Adsl2SymbolProtection
Adsl2TransmissionModeType
Adsl2TrellisMode
Adsl2Tssi
Adsl2Unit

From HUAWEI-MIB

huaweiUtility

OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
adsl2MIB	1.3.6.1.4.1.2011.6.111			This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. The MIB module described in RFC 2662 [RFC2662] describes objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413/1995 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2]. This document does not obsolete RFC 2662 [RFC2662], but rather provides a more comprehensive management model that includes the ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5], respectively). In addition, objects have been added to improve the management of ADSL, ADSL2, and ADSL2+ lines. Additionally, the management framework for New Generation ADSL lines specified by the Digital Subscriber Line Forum (DSLF) has been taken into consideration [TR-90]. That framework is based on ITU-T G.997.1 standard [G.997.1] as well as two amendments: [G.997.1 am1] and [G.997.1 am2]. Note that the revised ITU-T G.997.1 standard refers also to next generation of VDSL technology, known as VDSL2, per ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond the scope of this document. The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of this document. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC XXXX: see the RFC itself for full legal notices.
adsl2	1.3.6.1.4.1.2011.6.111.1
adsl2Notifications	1.3.6.1.4.1.2011.6.111.1.0
NTF adsl2LinePerfFECSThreshAtuc	1.3.6.1.4.1.2011.6.111.1.0.1			This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred ATU-C.
NTF adsl2LinePerfFECSThreshAtur	1.3.6.1.4.1.2011.6.111.1.0.2			This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred ATU-R.
NTF adsl2LinePerfESThreshAtuc	1.3.6.1.4.1.2011.6.111.1.0.3			This notification indicates that the errored seconds threshold has been reached/exceeded for the referred ATU-C.
NTF adsl2LinePerfESThreshAtur	1.3.6.1.4.1.2011.6.111.1.0.4			This notification indicates that the errored seconds threshold has been reached/exceeded for the referred ATU-R.
NTF adsl2LinePerfSESThreshAtuc	1.3.6.1.4.1.2011.6.111.1.0.5			This notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred ATU-C.
NTF adsl2LinePerfSESThreshAtur	1.3.6.1.4.1.2011.6.111.1.0.6			This notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred ATU-R.
NTF adsl2LinePerfLOSSThreshAtuc	1.3.6.1.4.1.2011.6.111.1.0.7			This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred ATU-C.
NTF adsl2LinePerfLOSSThreshAtur	1.3.6.1.4.1.2011.6.111.1.0.8			This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred ATU-R.
NTF adsl2LinePerfUASThreshAtuc	1.3.6.1.4.1.2011.6.111.1.0.9			This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred ATU-C.
NTF adsl2LinePerfUASThreshAtur	1.3.6.1.4.1.2011.6.111.1.0.10			This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred ATU-R.
NTF adsl2LinePerfCodingViolationsThreshAtuc	1.3.6.1.4.1.2011.6.111.1.0.11			This notification indicates that the coding violations threshold has been reached/exceeded for the referred ATU-C.
NTF adsl2LinePerfCodingViolationsThreshAtur	1.3.6.1.4.1.2011.6.111.1.0.12			This notification indicates that the coding violations threshold has been reached/exceeded for the referred ATU-R.
NTF adsl2LinePerfCorrectedThreshAtuc	1.3.6.1.4.1.2011.6.111.1.0.13			This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred ATU-C.
NTF adsl2LinePerfCorrectedThreshAtur	1.3.6.1.4.1.2011.6.111.1.0.14			This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred ATU-R.
NTF adsl2LinePerfFailedFullInitThresh	1.3.6.1.4.1.2011.6.111.1.0.15			This notification indicates that the failed full initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2 line.
NTF adsl2LinePerfFailedShortInitThresh	1.3.6.1.4.1.2011.6.111.1.0.16			This notification indicates that the failed short initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2 line.
NTF adsl2LineStatusChangeAtuc	1.3.6.1.4.1.2011.6.111.1.0.17			This notification indicates that a status change is detected for the referred ATU-C.
NTF adsl2LineStatusChangeAtur	1.3.6.1.4.1.2011.6.111.1.0.18			This notification indicates that a status change is detected for the referred ATU-R.
adsl2Line	1.3.6.1.4.1.2011.6.111.1.1
adsl2LineTable	1.3.6.1.4.1.2011.6.111.1.1.1		not-accessible	The table adsl2LineTable contains configuration, command and status parameters of the ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2. Several objects in this table MUST be maintained in a persistent manner.
adsl2LineEntry	1.3.6.1.4.1.2011.6.111.1.1.1.1		not-accessible	The table adsl2LineTable contains configuration, commands and status parameters of the ADSL2 line
STR adsl2LineCnfgTemplate	1.3.6.1.4.1.2011.6.111.1.1.1.1.1	SnmpAdminString	read-write	The value of this object identifies the row in the ADSL2 Line Configuration Templates Table, (adsl2LineConfTemplateTable), which applies for this ADSL2 line. This object MUST be maintained in a persistent manner.
STR adsl2LineAlarmCnfgTemplate	1.3.6.1.4.1.2011.6.111.1.1.1.1.2	SnmpAdminString	read-write	The value of this object identifies the row in the ADSL2 Line Alarm Configuration Template Table, (adsl2LineAlarmConfTemplateTable), which applies to this ADSL2 line. This object MUST be maintained in a persistent manner.
ADS adsl2LineCmndConfPmsf	1.3.6.1.4.1.2011.6.111.1.1.1.1.3	Adsl2ConfPmsForce	read-write	Power management state forced. Defines the line states to be forced by the near-end ATU on this line. The various possible values are: l3toL0 (0), l0toL2 (2), l0orL2toL3 (3). This object MUST be maintained in a persistent manner.
ADS adsl2LineCmndConfLdsf	1.3.6.1.4.1.2011.6.111.1.1.1.1.4	Adsl2LineLdsf	read-write	Loop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line or only be responsive to loop diagnostics initiated by the far-end ATU. This object MUST be maintained in a persistent manner. However, in case the operator forces loop diagnostics mode then the access node should reset the object (inhibit) when loop diagnostics mode procedures are completed.
ADS adsl2LineCmndConfLdsfFailReason	1.3.6.1.4.1.2011.6.111.1.1.1.1.5	Adsl2LdsfResult	read-only	The status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Possible values are: none (1) - The default value in case LDSF was never requested for the associated line. success (2) - The recent command completed successfully. inProgress (3) - The Loop Diagnostics process is in progress. unsupported (4) - The NE or the line card doesn't support LDSF. cannotRun (5) - The NE cannot initiate the command, due to a non specific reason. aborted (6) - The Loop Diagnostics process aborted. failed (7) - The Loop Diagnostics process failed. illegalMode (8) - The NE cannot initiate the command, due to the specific mode of the relevant line. adminUp (9) - The NE cannot initiate the command, as the relevant line is administratively 'Up'. tableFull (10)- The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources (11)- The NE cannot initiate the command, due to lack of internal memory resources.
T/F adsl2LineCmndAutomodeColdStart	1.3.6.1.4.1.2011.6.111.1.1.1.1.6	TruthValue	read-write	Automode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' indicates a change in loop conditions applied to the devices under test. The ATUs shall reset any historical information used for automode and for shortening G.994.1 handshake and initialization. Automode is the case where multiple operation-modes are enabled through the adsl2LConfProfAtuTransSysEna object in the line configuration profile being used for the ADSL line, and where the selection of the actual operation-mode depends not only on the common capabilities of both ATUs (as exchanged in G.994.1), but also on achievable data rates under given loop conditions. This object MUST be maintained in a persistent manner.
U32 adsl2LineStatusAtuTransSys	1.3.6.1.4.1.2011.6.111.1.1.1.1.7	Unsigned32	read-only	The ATU Transmission System (ATS) in use. This parameter may be derived from the handshaking procedures defined in Recommendation G.994.1. One of ADSL2 line transmission modes: ANSI_T1413(1) ETSI_DTS_TM06006(2) G9921_POTS_NONOVERLAP(3) G9921_POTS_OVERLAP(4) G9921_ISDN_NONOVERLAP(5) G9921_ISDN_OVERLAP(6) G9921_TCMISDN_NONOVERLAP(7) G9921_TCMISDN_OVERLAP(8) G9922_POTS_NONOVERLAP(9) G9922_POTS_OVERLAP(10) G9922_TCMISDN_NONOVERLAP(11) G9922_TCMISDN_OVERLAP(12) G9921_TCMISDN_SYMMETRIC(13) G9923_POTS_NONOVERLAP(19) G9923_POTS_OVERLAP(20) G9923_ISDN_NONOVERLAP(21) G9923_ISDN_OVERLAP(22) G9924_POTS_NONOVERLAP(25) G9924_POTS_OVERLAP(26) G9923_ANNEXI_ALLDIGI_NONOVERLAP(29) G9923_ANNEXI_ALLDIGI_OVERLAP(30) G9923_ANNEXJ_ALLDIGI_NONOVERLAP(31) G9923_ANNEXJ_ALLDIGI_OVERLAP(32) G9924_ANNEXI_ALLDIGI_NONOVERLAP(33) G9924_ANNEXI_ALLDIGI_OVERLAP(34) G9923_ANNEXL_POTS_NONOVERLAP_MODE1_WIDEUS(35) G9923_ANNEXL_POTS_NONOVERLAP_MODE2_NARROWUS(36) G9923_ANNEXL_POTS_OVERLAP_MODE3_WIDEUS(37) G9923_ANNEXL_POTS_NONOVERLAP_MODE4_NARROWUS(38) G9923_ANNEXM_POTS_NONOVERLAP(39) G9923_ANNEXM_POTS_OVERLAP(40) G9925_POTS_NONOVERLAP(41) G9925_POTS_OVERLAP(42) G9925_ISDN_NONOVERLAP(43) G9925_ISDN_OVERLAP(44) G9925_ANNEXI_ALLDIGI_NONOVERLAP(47) G9925_ANNEXI_ALLDIGI_OVERLAP(48) G9925_ANNEXJ_ALLDIGI_NONOVERLAP(49) G9925_ANNEXJ_ALLDIGI_OVERLAP(50) G9925_ANNEXM_POTS_NONOVERLAP(51) G9925_ANNEXM_POTS_OVERLAP(52)
ADS adsl2LineStatusPwrMngState	1.3.6.1.4.1.2011.6.111.1.1.1.1.8	Adsl2PowerMngState	read-only	The current power management state. One of four possible power management states: L0 - Synchronized and full transmission (i.e., Showtime), L1 - Low Power with reduced net data rate (G.992.2 only), L2 - Low Power with reduced net data rate (G.992.3 and G.992.4 only), L3 - No power The various possible values are:l0(1), l1(2), l2(3), l3(4).
ADS adsl2LineStatusInitResult	1.3.6.1.4.1.2011.6.111.1.1.1.1.9	Adsl2InitResult	read-only	Indicates the result of the last full initialization performed on the line. It is an enumeration type with the following values: noFail(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), otherCause(5).
ADS adsl2LineStatusLastStateDs	1.3.6.1.4.1.2011.6.111.1.1.1.1.10	Adsl2LastTransmittedState	read-only	The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line.
ADS adsl2LineStatusLastStateUs	1.3.6.1.4.1.2011.6.111.1.1.1.1.11	Adsl2LastTransmittedState	read-only	The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line.
ADS adsl2LineStatusAtur	1.3.6.1.4.1.2011.6.111.1.1.1.1.12	Adsl2LineStatus	read-only	Indicates current state (existing failures) of the ATU-R. This is a bit-map of possible conditions.
ADS adsl2LineStatusAtuc	1.3.6.1.4.1.2011.6.111.1.1.1.1.13	Adsl2LineStatus	read-only	Indicates current state (existing failures) of the ATU-C. This is a bit-map of possible conditions.
U32 adsl2LineStatusLnAttenDs	1.3.6.1.4.1.2011.6.111.1.1.1.1.14	Unsigned32	read-only	The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB).
U32 adsl2LineStatusLnAttenUs	1.3.6.1.4.1.2011.6.111.1.1.1.1.15	Unsigned32	read-only	The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB).
U32 adsl2LineStatusSigAttenDs	1.3.6.1.4.1.2011.6.111.1.1.1.1.16	Unsigned32	read-only	The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB).
U32 adsl2LineStatusSigAttenUs	1.3.6.1.4.1.2011.6.111.1.1.1.1.17	Unsigned32	read-only	The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB).
I32 adsl2LineStatusSnrMarginDs	1.3.6.1.4.1.2011.6.111.1.1.1.1.18	Integer32	read-only	Downstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-R, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB).
I32 adsl2LineStatusSnrMarginUs	1.3.6.1.4.1.2011.6.111.1.1.1.1.19	Integer32	read-only	Upstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-C, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB).
U32 adsl2LineStatusAttainableRateDs	1.3.6.1.4.1.2011.6.111.1.1.1.1.20	Unsigned32	read-only	Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the ATU-C transmitter and the ATU-R receiver, coded in bit/s.
U32 adsl2LineStatusAttainableRateUs	1.3.6.1.4.1.2011.6.111.1.1.1.1.21	Unsigned32	read-only	Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the ATU-R transmitter and the ATU-C receiver, coded in bit/s.
I32 adsl2LineStatusActPsdDs	1.3.6.1.4.1.2011.6.111.1.1.1.1.22	Integer32	read-only	Actual Power Spectrum Density (PSD) Downstream. The average downstream transmit PSD over the sub-carriers used for downstream. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz).
I32 adsl2LineStatusActPsdUs	1.3.6.1.4.1.2011.6.111.1.1.1.1.23	Integer32	read-only	Actual Power Spectrum Density (PSD) Upstream. The average upstream transmit PSD over the sub-carriers used for upstream. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz).
I32 adsl2LineStatusActAtpDs	1.3.6.1.4.1.2011.6.111.1.1.1.1.24	Integer32	read-only	Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the ATU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm).
I32 adsl2LineStatusActAtpUs	1.3.6.1.4.1.2011.6.111.1.1.1.1.25	Integer32	read-only	Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm).
adsl2Status	1.3.6.1.4.1.2011.6.111.1.2
adsl2ChannelStatusTable	1.3.6.1.4.1.2011.6.111.1.2.1		not-accessible	The table adsl2ChannelStatusTable contains status parameters of ADSL2 channel. This table contains live data from equipment.
adsl2ChannelStatusEntry	1.3.6.1.4.1.2011.6.111.1.2.1.1		not-accessible	The table adsl2ChannelStatusTable contains status parameters of ADSL2 channel. The index of this table is an interface index where the interface has an ifType value that is applicable for a DSL channel and the termination unit.
ADS adsl2ChStatusUnit	1.3.6.1.4.1.2011.6.111.1.2.1.1.1	Adsl2Unit	not-accessible	The termination unit ATUC(1) or ATUR(2).
U32 adsl2ChStatusChannelNum	1.3.6.1.4.1.2011.6.111.1.2.1.1.2	Unsigned32	read-only	Provides the bearer channel number associated with this row (i.e., the channel ifIndex). This enables determining the channel configuration profile and the channel thresholds profile applicable for this bearer channel.
U32 adsl2ChStatusActDataRate	1.3.6.1.4.1.2011.6.111.1.2.1.1.3	Unsigned32	read-only	The actual net data rate that the bearer channel is operating at, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. The data rate is coded in bit/s.
U32 adsl2ChStatusPrevDataRate	1.3.6.1.4.1.2011.6.111.1.2.1.1.4	Unsigned32	read-only	The previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fast retrain, DRA or power management transitions, excluding transitions between L0 state and L1 or L2 states. The data rate is coded in bit/s.
U32 adsl2ChStatusActDelay	1.3.6.1.4.1.2011.6.111.1.2.1.1.5	Unsigned32	read-only	The actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. It is coded in ms (rounded to the nearest ms).
ADS adsl2ChStatusAtmStatus	1.3.6.1.4.1.2011.6.111.1.2.1.1.6	Adsl2ChAtmStatus	read-only	Indicates current state (existing failures) of the ADSL channel in case its Data Path is ATM. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), noCellDelineation(1), lossOfCellDelineation (2). In case the channel is not of ATM Data Path the object is set to '0'.
ADS adsl2ChStatusPtmStatus	1.3.6.1.4.1.2011.6.111.1.2.1.1.7	Adsl2ChPtmStatus	read-only	Indicates current state (existing failures) of the ADSL channel in case its Data Path is PTM. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), outOfSync (1). In case the channel is not of PTM Data Path the object is set to '0'.
U32 adsl2ChStatusINP	1.3.6.1.4.1.2011.6.111.1.2.1.1.65535	Unsigned32	read-only	The actual impulse noise protection (INP) on the bearer channel in L0 state.
U32 adsl2ChStatusRSRedundancy	1.3.6.1.4.1.2011.6.111.1.2.1.1.65536	Unsigned32	read-only	The actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. It ranges from 0 to 16. The value 0 indicates no Reed-Solomon coding.
U32 adsl2ChStatusRSSymbols	1.3.6.1.4.1.2011.6.111.1.2.1.1.65537	Unsigned32	read-only	the DMT Symbol number per codeword used in the latency path in which the bearer channel is transported.
U32 adsl2ChStatusInterDepth	1.3.6.1.4.1.2011.6.111.1.2.1.1.65538	Unsigned32	read-only	The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 by step of 1. The value 1 indicates no interleaving.
U32 adsl2ChStatusSymbolLength	1.3.6.1.4.1.2011.6.111.1.2.1.1.65539	Unsigned32	read-only	The actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead.
U32 adsl2ChStatusRSSize	1.3.6.1.4.1.2011.6.111.1.2.1.1.65540	Unsigned32	read-only	The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported.
adsl2SCStatusTable	1.3.6.1.4.1.2011.6.111.1.2.2		not-accessible	The table adsl2SCStatusTable contains status parameters of ADSL2 sub-carriers. This following points apply to this table : 1. The main purpose of this table is to hold the results of a DELT test. 2. This table also holds parameters obtained at line initialisation time. 3. The rows in this table are volatile, that is they are lost if the SNMP agent is rebooted. 4. Due to the large OCTET STRING attributes in this table, the worst case memory requirements for this table are very high. The manager may use the row status attribute of this table to delete rows in order to reclaim memory. 5. The manager may create rows in this table. The SNMP agent may create rows in this table. Only the manager may delete rows in this table. 6. The maximum number of rows allowable in this table is indicated by the scalar attribute adsl2ScalarSCMaxInterfaces. The number of rows available in this table is indicated by the scalar attribute adsl2ScalarSCAvailInterfaces. 7. The SNMP agent is permitted to create rows in this table when a DELT test completes successfully or when line initialisation occurs. It is not mandatory for the SNMP agent to create rows in this table, hence it may be necessary for the manager to create rows in this table before any results can be stored. 8. If the manager attempts to create a row in this table and there are no more rows available, the creation attempt will fail and the response to the SNMP SET PDU will contain the error noCreation(11). 9. If the SNMP agent attempts to create a row in this table and there are no more rows available, the creation attempt will fail and the attribute adsl2LineCmndConfLdsfFailReason will indicate the reason for the failure. The failure reason will be either tableFull(10) or noResources(11). 10. An example of use of this table is as follows : Step 1. : The DELT test is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT test completes and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : Due to a low memory condition, a row in the : adsl2SCStatusTable table cannot be created at : this time. Step 5. : The reason for the failure, tableFull(10), is : indicated in the adsl2LineCmndConfLdsfFailReason : attribute. 11. Another example of use of this table is as follows : Step 1. : The DELT test is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT test completes and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : The row creation is successfully. Step 5. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). 12. Another example of use of this table is as follows : Step 1. : The manager creates a row in adsl2SCStatusTable : for a particular ADSL2 line. Step 2. : The DELT test is started on the above mentioned : line by setting the adsl2LineCmndConfLdsf from : inhibit to force. Step 3. : The DELT test completes and valid data is : available. Step 4. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2).
adsl2SCStatusEntry	1.3.6.1.4.1.2011.6.111.1.2.2.1		not-accessible	The table Hfadsl2SCStatusEntry contains status parameters of ADSL2 sub-carriers. The index of this table is an interface index where the interface has an ifType of adsl2.
ADS adsl2SCStatusDirection	1.3.6.1.4.1.2011.6.111.1.2.2.1.1	Adsl2Direction	not-accessible	The direction of the sub-carrier either upstream or downstream
U32 adsl2SCStatusMtime	1.3.6.1.4.1.2011.6.111.1.2.2.1.2	Unsigned32	read-only	SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated otherwise
OCT adsl2SCStatusSnr	1.3.6.1.4.1.2011.6.111.1.2.2.1.3	OCTET STRING	read-only	The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Octet i (0 <= i < NSC) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the subcarrier because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide.
OCT adsl2SCStatusBitsAlloc	1.3.6.1.4.1.2011.6.111.1.2.2.1.4	OCTET STRING	read-only	The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Nibble i (0 <= i < NSC) is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier i has the same amount of bits allocation.
OCT adsl2SCStatusGainAlloc	1.3.6.1.4.1.2011.6.111.1.2.2.1.5	OCTET STRING	read-only	The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier i has the same amount of gain value. The gain value is represented as a multiple of 1/512 on linear scale. Each value in this array is 16 bits wide and is stored in big endian format.
ADS adsl2SCStatusTssi	1.3.6.1.4.1.2011.6.111.1.2.2.1.6	Adsl2Tssi	read-only	The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 octets with the following structure: First 2 octets - Index of the subcarrier used in the context of the breakpoint. Third octet - The shaping parameter at the breakpoint. Subcarrier index is an unsigned number in the range 1 to either NSCds (downstream direction) or NSCus (upstream direction). The shaping parameter value is in the range 0 to 127 (units of -0.5dB). The special value 127 indicates that the subcarrier is not transmitted.
U32 adsl2SCStatusLinScale	1.3.6.1.4.1.2011.6.111.1.2.2.1.7	Unsigned32	read-only	The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure.
OCT adsl2SCStatusLinReal	1.3.6.1.4.1.2011.6.111.1.2.2.1.8	OCTET STRING	read-only	An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Each array entry represents the real component [referred here as a(i)] of Hlin(f = iDf) value for a particular sub-carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) and b(i) [provided by the Adsl2SubcarrierLinImg object] are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format.
OCT adsl2SCStatusLinImg	1.3.6.1.4.1.2011.6.111.1.2.2.1.9	OCTET STRING	read-only	An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Each array entry represents the imaginary component [referred here as b(i)] of Hlin(f = iDf) value for a particular sub- carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) [provided by the Adsl2SubcarrierLinReal object] and b(i) are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format.
U32 adsl2SCStatusLogMt	1.3.6.1.4.1.2011.6.111.1.2.2.1.10	Unsigned32	read-only	The number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization
OCT adsl2SCStatusLog	1.3.6.1.4.1.2011.6.111.1.2.2.1.11	OCTET STRING	read-only	An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Each array entry represents the real Hlog(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format.
U32 adsl2SCStatusQlnMt	1.3.6.1.4.1.2011.6.111.1.2.2.1.12	Unsigned32	read-only	The number of symbols used to measure the Quiet Line Noise values on the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization
OCT adsl2SCStatusQln	1.3.6.1.4.1.2011.6.111.1.2.2.1.13	OCTET STRING	read-only	An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide.
U32 adsl2SCStatusLnAtten	1.3.6.1.4.1.2011.6.111.1.2.2.1.14	Unsigned32	read-only	When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub-carriers during diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub-carriers during diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
U32 adsl2SCStatusSigAtten	1.3.6.1.4.1.2011.6.111.1.2.2.1.15	Unsigned32	read-only	When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub carriers during Showtime after the diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub carriers during Showtime after the diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
I32 adsl2SCStatusSnrMargin	1.3.6.1.4.1.2011.6.111.1.2.2.1.16	Integer32	read-only	SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB). This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
U32 adsl2SCStatusAttainableRate	1.3.6.1.4.1.2011.6.111.1.2.2.1.17	Unsigned32	read-only	Maximum Attainable Data Rate. The maximum net data rate currently attainable by the ATU-C transmitter and ATU-R receiver (when referring to downstream direction) or by the ATU-R transmitter and ATU-C receiver (when referring to upstream direction). Value is coded in bits/s. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
I32 adsl2SCStatusActAtp	1.3.6.1.4.1.2011.6.111.1.2.2.1.18	Integer32	read-only	Actual Aggregate Transmit Power from the ATU (ATU-R on downstream direction and ATU-C on upstream direction), at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm). A value of all 1's indicates the measurement is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
ROW adsl2SCStatusRowStatus	1.3.6.1.4.1.2011.6.111.1.2.2.1.19	RowStatus	read-create	Row Status. The manager may create and delete rows of this table. Please see the description of adsl2SCStatusTable above for more details.
adsl2Inventory	1.3.6.1.4.1.2011.6.111.1.3
adsl2LineInventoryTable	1.3.6.1.4.1.2011.6.111.1.3.1		not-accessible	The table adsl2LineInventoryTable contains inventory of ADSL2 unit.
adsl2LineInventoryEntry	1.3.6.1.4.1.2011.6.111.1.3.1.1		not-accessible	The table adsl2LineInventoryTable contains inventory of ADSL2 unit. The index of this table is an interface index where the interface has an ifType of adsl2(230).
ADS adsl2LInvUnit	1.3.6.1.4.1.2011.6.111.1.3.1.1.1	Adsl2Unit	not-accessible	The termination unit ATUC{1} or ATUR{2}.
OCT adsl2LInvG994VendorId	1.3.6.1.4.1.2011.6.111.1.3.1.1.2	OCTET STRING	read-only	The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as defined in Recommendation T.35.
OCT adsl2LInvSystemVendorId	1.3.6.1.4.1.2011.6.111.1.3.1.1.3	OCTET STRING	read-only	The ATU System Vendor ID (identifies the ATU system integrator) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of 8 binary octets, with same format as used for Adsl2InvG994VendorId.
OCT adsl2LInvVersionNumber	1.3.6.1.4.1.2011.6.111.1.3.1.1.4	OCTET STRING	read-only	The ATU version number (vendor specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of up to 16 binary octets.
OCT adsl2LInvSerialNumber	1.3.6.1.4.1.2011.6.111.1.3.1.1.5	OCTET STRING	read-only	The ATU serial number (vendor specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It is vendor specific information. It consists of up to 32 ASCII characters.
OCT adsl2LInvSelfTestResult	1.3.6.1.4.1.2011.6.111.1.3.1.1.6	OCTET STRING	read-only	The ATU self-test result, coded as a 32-bit value. The most significant octet of the result is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discretionary.
ADS adsl2LInvTransmissionCapabilities	1.3.6.1.4.1.2011.6.111.1.3.1.1.7	Adsl2TransmissionModeType	read-only	The ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1. A set of ADSL2 line transmission modes, with one bit per mode.
adsl2PM	1.3.6.1.4.1.2011.6.111.1.4
adsl2PMLine	1.3.6.1.4.1.2011.6.111.1.4.1
adsl2PMLineCurrTable	1.3.6.1.4.1.2011.6.111.1.4.1.1		not-accessible	The table adsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line.
adsl2PMLineCurrEntry	1.3.6.1.4.1.2011.6.111.1.4.1.1.1		not-accessible	The table adsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230) and the termination unit. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
ADS adsl2PMLCurrUnit	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.1	Adsl2Unit	not-accessible	The termination unit ATUC{1} or ATUR{2}.
U32 adsl2PMLCurrValidIntervals	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.2	Unsigned32	read-only	Valid intervals.
U32 adsl2PMLCurrInvalidIntervals	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.3	Unsigned32	read-only	Invalid intervals.
HCP adsl2PMLCurr15MTimeElapsed	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.4	HCPerfTimeElapsed	read-only	Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
C32 adsl2PMLCurr15MFecs	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.5	Counter32	read-only	Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
C32 adsl2PMLCurr15MEs	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.6	Counter32	read-only	Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 . This parameter is inhibited during UAS.
C32 adsl2PMLCurr15MSes	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.7	Counter32	read-only	Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 . This parameter is inhibited during UAS.
C32 adsl2PMLCurr15MLoss	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.8	Counter32	read-only	Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R).
C32 adsl2PMLCurr15MUas	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.9	Counter32	read-only	Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely-errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
U32 adsl2PMLCurr1DayValidIntervals	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.10	Unsigned32	read-only	Valid intervals.
U32 adsl2PMLCurr1DayInvalidIntervals	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.11	Unsigned32	read-only	Invalid intervals.
HCP adsl2PMLCurr1DayTimeElapsed	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.12	HCPerfTimeElapsed	read-only	Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
C32 adsl2PMLCurr1DayFecs	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.13	Counter32	read-only	Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
C32 adsl2PMLCurr1DayEs	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.14	Counter32	read-only	Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
C32 adsl2PMLCurr1DaySes	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.15	Counter32	read-only	Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS.
C32 adsl2PMLCurr1DayLoss	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.16	Counter32	read-only	Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R).
C32 adsl2PMLCurr1DayUas	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.17	Counter32	read-only	Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
C32 adsl2PMLEverBeforeFecs	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.18	Counter32	read-only	Count of seconds since agent reset that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
C32 adsl2PMLEverBeforeEs	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.19	Counter32	read-only	Count of seconds since agent reset that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
C32 adsl2PMLEverBeforeSes	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.20	Counter32	read-only	Count of seconds since agent reset that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS.
C32 adsl2PMLEverBeforeLoss	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.21	Counter32	read-only	Count of seconds since agent reset that there was LOS (or LOS-FE for ATU-R).
C32 adsl2PMLEverBeforeUas	1.3.6.1.4.1.2011.6.111.1.4.1.1.1.22	Counter32	read-only	Count of seconds in Unavailability State since agent reset. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
adsl2PMLineCurrInitTable	1.3.6.1.4.1.2011.6.111.1.4.1.2		not-accessible	The table adsl2PMLineCurrInitTable contains current initialization counters of ADSL2 line. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
adsl2PMLineCurrInitEntry	1.3.6.1.4.1.2011.6.111.1.4.1.2.1		not-accessible	The table adsl2PMLineCurrInitTable contains current initialization counters of ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230) and the termination unit.
U32 adsl2PMLCurrInit15MTimeElapsed	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.1	Unsigned32	read-only	Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
U32 adsl2PMLCurrInit15MFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.2	Unsigned32	read-only	Count of full initializations attempted on the line (successful and failed) during this interval.
U32 adsl2PMLCurrInit15MFailedFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.3	Unsigned32	read-only	Count of failed full initializations on the line during this interval.
U32 adsl2PMLCurrInit15MShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.4	Unsigned32	read-only	Count of short initializations attempted on the line (successful and failed) during this interval.
U32 adsl2PMLCurrInit15MFailedShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.5	Unsigned32	read-only	Count of failed short initializations on the line during this interval.
U32 adsl2PMLCurrInit1DayTimeElapsed	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.6	Unsigned32	read-only	Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
U32 adsl2PMLCurrInit1DayFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.7	Unsigned32	read-only	Count of full initializations attempted on the line (successful and failed) during this interval.
U32 adsl2PMLCurrInit1DayFailedFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.8	Unsigned32	read-only	Count of failed full initializations on the line during this interval.
U32 adsl2PMLCurrInit1DayShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.9	Unsigned32	read-only	Count of short initializations attempted on the line (successful and failed) during this interval.
U32 adsl2PMLCurrInit1DayFailedShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.10	Unsigned32	read-only	Count of failed short initializations on the line during this interval.
U32 adsl2PMLInitEverBeforeFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.11	Unsigned32	read-only	Count of full initializations attempted on the line (successful and failed) since agent reset.
U32 adsl2PMLInitEverBeforeFailedFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.12	Unsigned32	read-only	Count of failed full initializations on the line since agent reset.
U32 adsl2PMLInitEverBeforeShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.13	Unsigned32	read-only	Count of short initializations attempted on the line (successful and failed) since agent reset.
U32 adsl2PMLInitEverBeforeFailedShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.2.1.14	Unsigned32	read-only	Count of failed short initializations on the line since agent reset.
adsl2PMLineHist15MinTable	1.3.6.1.4.1.2011.6.111.1.4.1.3		not-accessible	The table adsl2PMLineHist15MinTable contains PM line history for 15min intervals of ADSL2 line.
adsl2PMLineHist15MinEntry	1.3.6.1.4.1.2011.6.111.1.4.1.3.1		not-accessible	The table adsl2PMLineHist15MinTable contains PM line history for 15min intervals of ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230), the termination unit, and an interval number.
ADS adsl2PMLHist15MUnit	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.1	Adsl2Unit	not-accessible	The termination unit ATUC{1} or ATUR{2}.
U32 adsl2PMLHist15MInterval	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.2	Unsigned32	not-accessible	The interval number.
U32 adsl2PMLHist15MMonitoredTime	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.3	Unsigned32	read-only	Total seconds monitored in this interval.
C32 adsl2PMLHist15MFecs	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.4	Counter32	read-only	Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
C32 adsl2PMLHist15MEs	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.5	Counter32	read-only	Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
C32 adsl2PMLHist15MSes	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.6	Counter32	read-only	Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
C32 adsl2PMLHist15MLoss	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.7	Counter32	read-only	Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R).
C32 adsl2PMLHist15MUas	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.8	Counter32	read-only	Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
T/F adsl2PMLHist15MValidInterval	1.3.6.1.4.1.2011.6.111.1.4.1.3.1.9	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adsl2PMLineHist1DayTable	1.3.6.1.4.1.2011.6.111.1.4.1.4		not-accessible	The table adsl2PMLineHist1DayTable contains PM line history for 24 hours intervals of ADSL2 line.
adsl2PMLineHist1DayEntry	1.3.6.1.4.1.2011.6.111.1.4.1.4.1		not-accessible	The table adsl2PMLineHist1DayTable contains PM line history for 24 hours intervals of ADSL2 line. The indexes of this table is an interface index where the interface has an ifType of adsl2(230), the termination unit and an interval number.
ADS adsl2PMLHist1DUnit	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.1	Adsl2Unit	not-accessible	The termination unit.
U32 adsl2PMLHist1DInterval	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.2	Unsigned32	not-accessible	The interval number.
U32 adsl2PMLHist1DMonitoredTime	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.3	Unsigned32	read-only	Total seconds monitored in this interval.
C32 adsl2PMLHist1DFecs	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.4	Counter32	read-only	Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
C32 adsl2PMLHist1DEs	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.5	Counter32	read-only	Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
C32 adsl2PMLHist1DSes	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.6	Counter32	read-only	Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >> 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
C32 adsl2PMLHist1DLoss	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.7	Counter32	read-only	Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R).
C32 adsl2PMLHist1DUas	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.8	Counter32	read-only	Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
T/F adsl2PMLHist1DValidInterval	1.3.6.1.4.1.2011.6.111.1.4.1.4.1.9	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adsl2PMLineInitHist15MinTable	1.3.6.1.4.1.2011.6.111.1.4.1.5		not-accessible	The table adsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of ADSL2 line.
adsl2PMLineInitHist15MinEntry	1.3.6.1.4.1.2011.6.111.1.4.1.5.1		not-accessible	The table adsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230) and an interval number.
U32 adsl2PMLHistInit15MInterval	1.3.6.1.4.1.2011.6.111.1.4.1.5.1.1	Unsigned32	not-accessible	The interval number.
U32 adsl2PMLHistInit15MMonitoredTime	1.3.6.1.4.1.2011.6.111.1.4.1.5.1.2	Unsigned32	read-only	Total seconds monitored in this interval.
U32 adsl2PMLHistInit15MFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.5.1.3	Unsigned32	read-only	Count of full initializations attempted on the line (successful and failed) during this interval.
U32 adsl2PMLHistInit15MFailedFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.5.1.4	Unsigned32	read-only	Count of failed full initializations on the line during this interval.
U32 adsl2PMLHistInit15MShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.5.1.5	Unsigned32	read-only	Count of short initializations attempted on the line (successful and failed) during this interval.
U32 adsl2PMLHistInit15MFailedShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.5.1.6	Unsigned32	read-only	Count of failed short initializations on the line during this interval.
T/F adsl2PMLHistInit15MValidInterval	1.3.6.1.4.1.2011.6.111.1.4.1.5.1.7	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adsl2PMLineInitHist1DayTable	1.3.6.1.4.1.2011.6.111.1.4.1.6		not-accessible	The table adsl2PMLineInitHist1DayTable contains PM line initialization history for 24 hours intervals of ADSL2 line.
adsl2PMLineInitHist1DayEntry	1.3.6.1.4.1.2011.6.111.1.4.1.6.1		not-accessible	The table adsl2PMLineInitHist1DayTable contains PM line initialization history for 24 hours intervals of ADSL2 line. The indexes of this table is an interface index where the interface has an ifType of adsl2(230) and an interval number.
U32 adsl2PMLHistinit1DInterval	1.3.6.1.4.1.2011.6.111.1.4.1.6.1.1	Unsigned32	not-accessible	The interval number.
U32 adsl2PMLHistinit1DMonitoredTime	1.3.6.1.4.1.2011.6.111.1.4.1.6.1.2	Unsigned32	read-only	Total seconds monitored in this interval.
U32 adsl2PMLHistinit1DFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.6.1.3	Unsigned32	read-only	Count of full initializations attempted on the line (successful and failed) during this interval.
U32 adsl2PMLHistinit1DFailedFullInits	1.3.6.1.4.1.2011.6.111.1.4.1.6.1.4	Unsigned32	read-only	Count of failed full initializations on the line during this interval.
U32 adsl2PMLHistinit1DShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.6.1.5	Unsigned32	read-only	Count of short initializations attempted on the line (successful and failed) during this interval.
U32 adsl2PMLHistinit1DFailedShortInits	1.3.6.1.4.1.2011.6.111.1.4.1.6.1.6	Unsigned32	read-only	Count of failed short initializations on the line during this interval.
T/F adsl2PMLHistinit1DValidInterval	1.3.6.1.4.1.2011.6.111.1.4.1.6.1.7	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adsl2PMChannel	1.3.6.1.4.1.2011.6.111.1.4.2
adsl2PMChCurrTable	1.3.6.1.4.1.2011.6.111.1.4.2.1		not-accessible	The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
adsl2PMChCurrEntry	1.3.6.1.4.1.2011.6.111.1.4.2.1.1		not-accessible	The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. The indexes of this table is an interface index where the interface has an ifType value which is applicable for a DSL channel and the termination unit.
ADS adsl2PMChCurrUnit	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.1	Adsl2Unit	not-accessible	The termination unit.
U32 adsl2PMChCurrValidIntervals	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.2	Unsigned32	read-only	Valid intervals.
U32 adsl2PMChCurrInvalidIntervals	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.3	Unsigned32	read-only	Invalid intervals.
HCP adsl2PMChCurr15MTimeElapsed	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.4	HCPerfTimeElapsed	read-only	Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
U32 adsl2PMChCurr15MCodingViolations	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.5	Unsigned32	read-only	Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
U32 adsl2PMChCurr15MCorrectedBlocks	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.6	Unsigned32	read-only	Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
U32 adsl2PMChCurr1DayValidIntervals	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.7	Unsigned32	read-only	Valid intervals.
U32 adsl2PMChCurr1DayInvalidIntervals	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.8	Unsigned32	read-only	Invalid intervals.
HCP adsl2PMChCurr1DayTimeElapsed	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.9	HCPerfTimeElapsed	read-only	Total elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized.
U32 adsl2PMChCurr1DayCodingViolations	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.10	Unsigned32	read-only	Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
U32 adsl2PMChCurr1DayCorrectedBlocks	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.11	Unsigned32	read-only	Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
U32 adsl2PMChEverBeforeCodingViolations	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.12	Unsigned32	read-only	Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
U32 adsl2PMChEverBeforeCorrectedBlocks	1.3.6.1.4.1.2011.6.111.1.4.2.1.1.13	Unsigned32	read-only	Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
adsl2PMChHist15MinTable	1.3.6.1.4.1.2011.6.111.1.4.2.2		not-accessible	The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel.
adsl2PMChHist15MinEntry	1.3.6.1.4.1.2011.6.111.1.4.2.2.1		not-accessible	The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. The indexes of this table is an interface index where the interface has an ifType value which is applicable for a DSL channel, the termination unit and the interval number.
ADS adsl2PMChHist15MUnit	1.3.6.1.4.1.2011.6.111.1.4.2.2.1.1	Adsl2Unit	not-accessible	The termination unit.
U32 adsl2PMChHist15MInterval	1.3.6.1.4.1.2011.6.111.1.4.2.2.1.2	Unsigned32	not-accessible	The interval number.
U32 adsl2PMChHist15MMonitoredTime	1.3.6.1.4.1.2011.6.111.1.4.2.2.1.3	Unsigned32	read-only	Total seconds monitored in this interval.
U32 adsl2PMChHist15MCodingViolations	1.3.6.1.4.1.2011.6.111.1.4.2.2.1.4	Unsigned32	read-only	Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
U32 adsl2PMChHist15MCorrectedBlocks	1.3.6.1.4.1.2011.6.111.1.4.2.2.1.5	Unsigned32	read-only	Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
T/F adsl2PMChHist15MValidInterval	1.3.6.1.4.1.2011.6.111.1.4.2.2.1.6	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adsl2PMChHist1DTable	1.3.6.1.4.1.2011.6.111.1.4.2.3		not-accessible	The table adsl2PMChHist1DayTable contains PM channel history for 1 day intervals of ADSL2.
adsl2PMChHist1DEntry	1.3.6.1.4.1.2011.6.111.1.4.2.3.1		not-accessible	The table adsl2PMChHist1DayTable contains PM channel history for 1 day intervals of ADSL2. The indexes of this table is an interface index where the interface has an ifType value which is applicable for a DSL channel, the termination unit and the interval number.
ADS adsl2PMChHist1DUnit	1.3.6.1.4.1.2011.6.111.1.4.2.3.1.1	Adsl2Unit	not-accessible	The termination unit.
U32 adsl2PMChHist1DInterval	1.3.6.1.4.1.2011.6.111.1.4.2.3.1.2	Unsigned32	not-accessible	The interval number.
U32 adsl2PMChHist1DMonitoredTime	1.3.6.1.4.1.2011.6.111.1.4.2.3.1.3	Unsigned32	read-only	Total seconds monitored in this interval.
U32 adsl2PMChHist1DCodingViolations	1.3.6.1.4.1.2011.6.111.1.4.2.3.1.4	Unsigned32	read-only	Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
U32 adsl2PMChHist1DCorrectedBlocks	1.3.6.1.4.1.2011.6.111.1.4.2.3.1.5	Unsigned32	read-only	Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
T/F adsl2PMChHist1DValidInterval	1.3.6.1.4.1.2011.6.111.1.4.2.3.1.6	TruthValue	read-only	This variable indicates if the data for this interval is valid.
adsl2Profile	1.3.6.1.4.1.2011.6.111.1.5
adsl2ProfileLine	1.3.6.1.4.1.2011.6.111.1.5.1
adsl2LineConfTemplateTable	1.3.6.1.4.1.2011.6.111.1.5.1.1		not-accessible	The table adsl2LineConfTemplateTable contains ADSL2 line configuration template. Entries in this table MUST be maintained in a persistent manner.
adsl2LineConfTemplateEntry	1.3.6.1.4.1.2011.6.111.1.5.1.1.1		not-accessible	The table adsl2LineConfTemplateTable contains ADSL2 line configuration template. A default template with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
STR adsl2LConfTempTemplateName	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.1	SnmpAdminString	not-accessible	This object identifies a row in this table.
STR adsl2LConfTempLineProfile	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.2	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Line Configuration Profile Table, (Adsl2LineConfProfileTable), which applies for this ADSL2 line.
STR adsl2LConfTempChan1ConfProfile	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.3	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the adsl2ChConfProfileTable table.
U32 adsl2LConfTempChan1RaRatioDs	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.4	Unsigned32	read-create	Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan1RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.
U32 adsl2LConfTempChan1RaRatioUs	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.5	Unsigned32	read-create	Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan1RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100 %.
STR adsl2LConfTempChan2ConfProfile	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.6	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel #2. If the channel is unused, then the object is set to a zero length string. This object may be set to a zero length string only if adsl2LConfTempChan3ConfProfile contains a zero length string.
U32 adsl2LConfTempChan2RaRatioDs	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.7	Unsigned32	read-create	Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan2RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.
U32 adsl2LConfTempChan2RaRatioUs	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.8	Unsigned32	read-create	Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan2RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100 %.
STR adsl2LConfTempChan3ConfProfile	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.9	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel #3. If the channel is unused, then the object is set to a zero length string. This object may be set to a zero length string only if adsl2LConfTempChan4ConfProfile contains a zero length string. This object may be set to a non-zero length string only if adsl2LConfTempChan2ConfProfile contains a non-zero length string.
U32 adsl2LConfTempChan3RaRatioDs	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.10	Unsigned32	read-create	Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan3RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.
U32 adsl2LConfTempChan3RaRatioUs	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.11	Unsigned32	read-create	Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan3RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.
STR adsl2LConfTempChan4ConfProfile	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.12	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (Adsl2ChanConfProfileTableDs) that applies to ADSL2 bearer channel #4. If the channel is unused, then the object is set to a zero length string. This object may be set to a non-zero length string only if adsl2LConfTempChan3ConfProfile contains a non-zero length string.
U32 adsl2LConfTempChan4RaRatioDs	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.13	Unsigned32	read-create	Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan4RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%.
U32 adsl2LConfTempChan4RaRatioUs	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.14	Unsigned32	read-create	Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan4RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%.
ROW adsl2LConfTempRowStatus	1.3.6.1.4.1.2011.6.111.1.5.1.1.1.15	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the template. Before a template can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must be first unreferenced from all associated lines.
adsl2LineConfProfTable	1.3.6.1.4.1.2011.6.111.1.5.1.2		not-accessible	The table adsl2LineConfProfTable contains ADSL2 line profile configuration. Entries in this table MUST be maintained in a persistent manner.
adsl2LineConfProfEntry	1.3.6.1.4.1.2011.6.111.1.5.1.2.1		not-accessible	The table adsl2LineConfProfTable contains ADSL2 line profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
STR adsl2LConfProfProfileName	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.1	SnmpAdminString	not-accessible	This object identifies a row in this table.
ADS adsl2LConfProfScMaskDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.2	Adsl2ScMaskDs	read-create	Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds i <= 512) should be set to '1'.
ADS adsl2LConfProfScMaskUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.3	Adsl2ScMaskUs	read-create	Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'.
ADS adsl2LConfProfRfiBandsDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.4	Adsl2RfiDs	read-create	The subset of downstream PSD mask breakpoints that shall be used to notch an RFI band. The specific interpolation around these points is defined in G.992.5. It is a bitmap of 512 bits that allows referring to up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is part of a notch filter, and if set to '0', the respective sub-carrier is not part of a notch filter. This information complements the specification provided by adsl2LconfProfPsdMaskDs. Note that if NSCds < 512, all bits i (NSCds
ADS adsl2LConfProfRaModeDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.5	Adsl2RaMode	read-create	The mode of operation of a rate-adaptive ATU-C in the transmit direction. The parameter can take three values: manual (1), raInit (2), dynamicRa (3).
ADS adsl2LConfProfRaModeUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.6	Adsl2RaMode	read-create	The mode of operation of a rate-adaptive ATU-R in the transmit direction. The parameter can take three values: manual (1), raInit (2), dynamicRa (3).
U32 adsl2LConfProfRaUsNrmDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.7	Unsigned32	read-create	The Downstream Up-Shift Noise Margin value, to be used when Adsl2LineConfRaModeDs is set to dynamicRa. If the downstream noise margin is above this value and stays above it for more than the time specified by the Adsl2LineConfRaUsTimeDs, the ATU-R shall attempt to increase the downstream net data rate. The Downstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
U32 adsl2LConfProfRaUsNrmUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.8	Unsigned32	read-create	The Upstream Up-Shift Noise Margin value, to be used when Adsl2LineConfRaModeUs is set to dynamicRa. If the upstream noise margin is above this value and stays above it for more than the time specified by the Adsl2LineConfRaUsTimeUs, the ATU-C shall attempt to increase the upstream net data rate. The Upstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
U32 adsl2LConfProfRaUsTimeDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.9	Unsigned32	read-create	The Downstream Up-Shift Time Interval, to be used when Adsl2LineConfRaModeDs is set to dynamicRa. The interval of time that the downstream noise margin should stay above the Downstream Up-shift Noise Margin before the ATU-R shall attempt to increase the downstream net data rate. The time interval ranges from 0 to 16383 seconds.
U32 adsl2LConfProfRaUsTimeUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.10	Unsigned32	read-create	The Upstream Up-Shift Time Interval, to be used when Adsl2LineConfRaModeUs is set to dynamicRa. The interval of time the upstream noise margin should stay above the Upstream Up-shift Noise Margin before the ATU-C shall attempt to increase the upstream net data rate. The time interval ranges from 0 to 16383 seconds.
U32 adsl2LConfProfRaDsNrmsDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.11	Unsigned32	read-create	The Downstream Down-Shift Noise Margin value, to be used when Adsl2LineConfRaModeDs is set to dynamicRa. If the downstream noise margin is below this value and stays below that for more than the time specified by the Adsl2LineConfRaDsTimeDs, the ATU-R shall attempt to decrease the downstream net data rate. The Downstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
U32 adsl2LConfProfRaDsNrmsUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.12	Unsigned32	read-create	The Upstream Downshift Noise Margin value, to be used when Adsl2LineConfRaModeUs is set to dynamicRa. If the upstream noise margin is below this value and stays below that for more than the time specified by the Adsl2LineConfRaDsTimeUs, the ATU-C shall attempt to decrease the upstream net data rate. The Upstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
U32 adsl2LConfProfRaDsTimeDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.13	Unsigned32	read-create	The Downstream Downshift Time Interval, to be used when Adsl2LineConfRaModeDs is set to dynamicRa. The interval of time the downstream noise margin should stay below the Downstream Down-shift Noise Margin before the ATU-R shall attempt to decrease the downstream net data rate. The time interval ranges from 0 to 16383 seconds.
U32 adsl2LConfProfRaDsTimeUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.14	Unsigned32	read-create	The Upstream Down-Shift Time Interval, to be used when Adsl2LineConfRaModeUs is set to dynamicRa. The interval of time the upstream noise margin should stay below the Upstream Down-shift Noise Margin before the ATU-C shall attempt to decrease the upstream net data rate. The time interval ranges from 0 to 16383 seconds.
U32 adsl2LConfProfTargetSnrmDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.15	Unsigned32	read-create	The minimum Noise Margin the ATU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
U32 adsl2LConfProfTargetSnrmUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.16	Unsigned32	read-create	The minimum Noise Margin the ATU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
U32 adsl2LConfProfMaxSnrmDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.17	Unsigned32	read-create	The maximum Noise Margin the ATU-R receiver shall try to sustain. If the Noise Margin is above this level, the ATU-R shall request that the ATU-C reduce the ATU-C transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
U32 adsl2LConfProfMaxSnrmUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.18	Unsigned32	read-create	The maximum Noise Margin the ATU-C receiver shall try to sustain. If the Noise Margin is above this level, the ATU-C shall request that the ATU-R reduce the ATU-R transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
U32 adsl2LConfProfMinSnrmDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.19	Unsigned32	read-create	The minimum Noise Margin the ATU-R receiver shall tolerate. If the noise margin falls below this level, the ATU-R shall request that the ATU-C increase the ATU-C transmit power. If an increase to ATU-C transmit power is not possible, a loss-of-margin (LOM) defect occurs, the ATU-R shall fail and attempt to reinitialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum.
U32 adsl2LConfProfMinSnrmUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.20	Unsigned32	read-create	The minimum Noise Margin the ATU-C receiver shall tolerate. If the noise margin falls below this level, the ATU-C shall request that the ATU-R increase the ATU-R transmit power. If an increase of ATU-R transmit power is not possible, a loss-of-margin (LOM) defect occurs, the ATU-C shall fail and attempt to re-initialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum.
U32 adsl2LConfProfMsgMinUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.21	Unsigned32	read-create	Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in upstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps.
U32 adsl2LConfProfMsgMinDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.22	Unsigned32	read-create	Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in downstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps.
ADS adsl2LConfProfAtuTransSysEna	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.23	Adsl2TransmissionModeType	read-create	ATU Transmission System Enabling (ATSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATUs may apply the respective coding for the ADSL line. A bit set to '0' means that the ATUs cannot apply the respective coding for the ADSL line. All 'reserved' bits should be set to '0'.
ADS adsl2LConfProfPmMode	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.24	Adsl2LConfProfPmMode	read-create	Power management state Enabling. Defines the power states the ATU-C or ATU-R may autonomously transition to on this line. The various bit positions are: allowTransitionsToIdle (0) and allowTransitionsToLowPower (1). A bit with a '1' value means that the ATU is allowed to transit into the respective state and a '0' value means that the ATU is not allowed to transit into the respective state.
U32 adsl2LConfProfL0Time	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.25	Unsigned32	read-create	This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds.
U32 adsl2LConfProfL2Time	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.26	Unsigned32	read-create	This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds.
U32 adsl2LConfProfL2Atpr	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.27	Unsigned32	read-create	The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB.
U32 adsl2LConfProfL2Atprt	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.28	Unsigned32	read-create	The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims.
ADS adsl2LConfProfTrellisMode	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.29	Adsl2TrellisMode	read-create	Enables and disables the Trellions mode. This object is defaulted enabled(2).
ADS adsl2LConfProfBitSwapDs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.30	Adsl2BitSwap	read-create	Enables and disables the bit swap downstream of a line.
ADS adsl2LConfProfBitSwapUs	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.31	Adsl2BitSwap	read-create	Enables and disables the bit swap upstream of a line.
ROW adsl2LConfProfRowStatus	1.3.6.1.4.1.2011.6.111.1.5.1.2.1.32	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must be first unreferenced from all associated templates.
adsl2LineConfProfModeSpecTable	1.3.6.1.4.1.2011.6.111.1.5.1.3		not-accessible	The table adsl2LineConfProfModeSpecTable extends the ADSL2 line configuration profile by ADSL Mode Specific parameters. A row in this table that has an index of adsl2LconfProfAdslMode == defMode(1), is called a 'mandatory' row. A row in this table that has an index such that adsl2LconfProfAdslMode is not equal to defMode(1), is called an 'optional' row. When a row in the adsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the adsl2LConfProfModeSpecRowStatus attribute will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the adsl2LConfProfModeSpecRowStatus attribute if the parent row exists. The manager MAY delete an 'optional' row in this table using the adsl2LConfProfModeSpecRowStatus attribute at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row. Entries in this table MUST be maintained in a persistent manner.
adsl2LineConfProfModeSpecEntry	1.3.6.1.4.1.2011.6.111.1.5.1.3.1		not-accessible	The table adsl2LineConfProfModeSpecTable extends the ADSL2 line configuration profile by ADSL Mode Specific parameters.
ADS adsl2LconfProfAdslMode	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.1	Adsl2OperationModes	not-accessible	The ADSL Mode is a way of categorizing the various ADSL transmission modes into groups, each group (ADSL Mode) shares the same PSD configuration. There should be multiple entries in this table for a given line profile in case multiple bits are set in adsl2LConfProfAtuTransSysEna for that profile.
I32 adsl2LConfProfMaxNomPsdDs	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.2	Integer32	read-create	The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz).
I32 adsl2LConfProfMaxNomPsdUs	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.3	Integer32	read-create	The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz).
U32 adsl2LConfProfMaxNomAtpDs	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.4	Unsigned32	read-create	The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).
U32 adsl2LConfProfMaxNomAtpUs	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.5	Unsigned32	read-create	The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).
I32 adsl2LConfProfMaxAggRxPwrUs	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.6	Integer32	read-create	The maximum upstream aggregate receive power over the relevant set of sub-carriers. The ATU-C should verify that the upstream power cutback is such that this maximum aggregate receive power value is honored. It ranges from -255 to 255 units of 0.1 dBm (physical values are -25.5 to 25.5 dBm).
ADS adsl2LConfProfPsdMaskDs	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.7	Adsl2PsdMaskDs	read-create	The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
ADS adsl2LConfProfPsdMaskUs	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.8	Adsl2PsdMaskUs	read-create	The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 4 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 9-11, which are associated with a 4th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 4, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
U32 adsl2LConfProfPsdMaskSelectUs	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.9	Unsigned32	read-create	The selected upstream PSD mask. This parameter is used only for annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in adsl2LConfProfAtuTransSysEna.
ROW adsl2LConfProfModeSpecRowStatus	1.3.6.1.4.1.2011.6.111.1.5.1.3.1.10	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must be first unreferenced from all associated templates.
adsl2ProfileChannel	1.3.6.1.4.1.2011.6.111.1.5.2
adsl2ChConfProfileTable	1.3.6.1.4.1.2011.6.111.1.5.2.1		not-accessible	The table adsl2ChConfProfileTable contains ADSL2 channel profile configuration. Entries in this table MUST be maintained in a persistent manner.
adsl2ChConfProfileEntry	1.3.6.1.4.1.2011.6.111.1.5.2.1.1		not-accessible	The table adsl2ChConfProfileTable contains ADSL2 channel profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
STR adsl2ChConfProfProfileName	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.1	SnmpAdminString	not-accessible	This object identifies a row in this table.
U32 adsl2ChConfProfMinDataRateDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.2	Unsigned32	read-create	Minimum Data Rate on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s.
U32 adsl2ChConfProfMinDataRateUs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.3	Unsigned32	read-create	Minimum Data Rate on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s.
U32 adsl2ChConfProfMinResDataRateDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.4	Unsigned32	read-create	Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Adsl2LineConfRaModeDs) is set to dynamicRa.
U32 adsl2ChConfProfMinResDataRateUs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.5	Unsigned32	read-create	Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Adsl2LineConfRaModeUs) is set to dynamicRa.
U32 adsl2ChConfProfMaxDataRateDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.6	Unsigned32	read-create	Maximum Data Rate on Downstream direction. The maximum net data rate for the bearer channel, coded in bit/s.
U32 adsl2ChConfProfMaxDataRateUs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.7	Unsigned32	read-create	Maximum Data Rate on Upstream direction. The maximum net data rate for the bearer channel, coded in bit/s.
U32 adsl2ChConfProfMinDataRateLowPwrDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.8	Unsigned32	read-create	Minimum Data Rate in Low Power state on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s., during the low power state (L1 in G.992.2, L2 in G.992.3).
U32 adsl2ChConfProfMaxDelayDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.9	Unsigned32	read-create	Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The ATUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Adsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Adsl2ChanConfMaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed.
U32 adsl2ChConfProfMaxDelayUs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.10	Unsigned32	read-create	Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The ATUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Adsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Adsl2ChanConfMaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed.
ADS adsl2ChConfProfMinProtectionDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.11	Adsl2SymbolProtection	read-create	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol.
ADS adsl2ChConfProfMinProtectionUs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.12	Adsl2SymbolProtection	read-create	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol.
ADS adsl2ChConfProfMaxBerDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.13	Adsl2MaxBer	read-create	Maximum Bit Error Ratio on Downstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7): eminus3 (1), eminus5 (2), eminus7 (3)
ADS adsl2ChConfProfMaxBerUs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.14	Adsl2MaxBer	read-create	Maximum Bit Error Ratio on Upstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7): eminus3 (1), eminus5 (2), eminus7 (3)
U32 adsl2ChConfProfUsDataRateDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.15	Unsigned32	read-create	Data Rate Threshold Up shift for downstream direction. An 'Up-shift rate change' event is triggered when the actual downstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s.
U32 adsl2ChConfProfDsDataRateDs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.16	Unsigned32	read-create	Data Rate Threshold Downshift for downstream direction. A 'Down-shift rate change' event is triggered when the actual downstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s.
U32 adsl2ChConfProfUsDataRateUs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.17	Unsigned32	read-create	Data Rate Threshold Up shift for upstream direction. An 'Up-shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s.
U32 adsl2ChConfProfDsDataRateUs	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.18	Unsigned32	read-create	Data Rate Threshold Downshift for upstream direction. A 'Down-shift rate change' event is triggered when the actual upstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s.
T/F adsl2ChConfProfImaEnabled	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.19	TruthValue	read-create	IMA Mode Enable. The parameter enables the IMA operation mode in the ATM Data Path. Relevant only if the channel is of ATM Data Path. When in 'enable' state, the ATM data path should comply with the requirements for IMA transmission.
ROW adsl2ChConfProfRowStatus	1.3.6.1.4.1.2011.6.111.1.5.2.1.1.20	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must be first unreferenced from all associated templates.
adsl2ProfileAlarmConf	1.3.6.1.4.1.2011.6.111.1.5.3
adsl2LineAlarmConfTemplateTable	1.3.6.1.4.1.2011.6.111.1.5.3.1		not-accessible	The table adsl2LineAlarmConfTemplateTable contains ADSL2 line configuration template. Entries in this table MUST be maintained in a persistent manner.
adsl2LineAlarmConfTemplateEntry	1.3.6.1.4.1.2011.6.111.1.5.3.1.1		not-accessible	The table adsl2LineAlarmConfTemplateTable contains ADSL2 line PM thresholds template. A default template with an index of 'DEFVAL' will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document
STR adsl2LAlarmConfTempTemplateName	1.3.6.1.4.1.2011.6.111.1.5.3.1.1.1	SnmpAdminString	not-accessible	This object identifies a row in this table.
STR adsl2LAlarmConfTempLineProfile	1.3.6.1.4.1.2011.6.111.1.5.3.1.1.2	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Line Thresholds Configuration Profile Table (adsl2LineAlarmConfProfileTable) that applies to this ADSL2 line.
STR adsl2LAlarmConfTempChan1ConfProfile	1.3.6.1.4.1.2011.6.111.1.5.3.1.1.3	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table.
STR adsl2LAlarmConfTempChan2ConfProfile	1.3.6.1.4.1.2011.6.111.1.5.3.1.1.4	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #2. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. If the channel is unused, then the object is set to a zero length string.
STR adsl2LAlarmConfTempChan3ConfProfile	1.3.6.1.4.1.2011.6.111.1.5.3.1.1.5	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #3. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. This object may be set to a non-zero length string only if adsl2LAlarmConfTempChan2ConfProfile contains a non-zero length string.
STR adsl2LAlarmConfTempChan4ConfProfile	1.3.6.1.4.1.2011.6.111.1.5.3.1.1.6	SnmpAdminString	read-create	The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #4. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. This object may be set to a non-zero length string only if adsl2LAlarmConfTempChan3ConfProfile contains a non-zero length string.
ROW adsl2LAlarmConfTempRowStatus	1.3.6.1.4.1.2011.6.111.1.5.3.1.1.7	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the template. Before a template can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must be first unreferenced from all associated lines.
adsl2LineAlarmConfProfileTable	1.3.6.1.4.1.2011.6.111.1.5.3.2		not-accessible	The table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. Entries in this table MUST be maintained in a persistent manner.
adsl2LineAlarmConfProfileEntry	1.3.6.1.4.1.2011.6.111.1.5.3.2.1		not-accessible	The table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document
STR adsl2LineAlarmConfProfileName	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.1	SnmpAdminString	not-accessible	This object identifies a row in this table.
NUM adsl2LineAlarmConfProfileAtucThresh15MinFecs	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.2	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is ATUC{1}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAtucThresh15MinEs	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.3	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is ATUC{1}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAtucThresh15MinSes	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.4	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAtucThresh15MinLoss	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.5	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAtucThresh15MinUas	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.6	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAturThresh15MinFecs	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.7	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAturThresh15MinEs	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.8	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAturThresh15MinSes	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.9	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAturThresh15MinLoss	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.10	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
NUM adsl2LineAlarmConfProfileAturThresh15MinUas	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.11	HCPerfIntervalThreshold	read-create	A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
U32 adsl2LineAlarmConfProfileThresh15MinFailedFullInt	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.12	Unsigned32	read-create	A threshold for the adsl2PMLCurrInit15MfailedFullInits counter. The value 0 means that no threshold is specified for the associated counter.
U32 adsl2LineAlarmConfProfileThresh15MinFailedShrtInt	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.13	Unsigned32	read-create	A threshold for the adsl2PMLCurrInit15MFailedShortInits counter. The value 0 means that no threshold is specified for the associated counter.
ROW adsl2LineAlarmConfProfileRowStatus	1.3.6.1.4.1.2011.6.111.1.5.3.2.1.14	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must be first unreferenced from all associated templates.
adsl2ChAlarmConfProfileTable	1.3.6.1.4.1.2011.6.111.1.5.3.3		not-accessible	The table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. Entries in this table MUST be maintained in a persistent manner.
adsl2ChAlarmConfProfileEntry	1.3.6.1.4.1.2011.6.111.1.5.3.3.1		not-accessible	The table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
STR adsl2ChAlarmConfProfileName	1.3.6.1.4.1.2011.6.111.1.5.3.3.1.1	SnmpAdminString	not-accessible	This object identifies a row in this table.
U32 adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations	1.3.6.1.4.1.2011.6.111.1.5.3.3.1.2	Unsigned32	read-create	A threshold for the adsl2PMChCurr15MCodingViolations counter, when adsl2PMChCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
U32 adsl2ChAlarmConfProfileAtucThresh15MinCorrected	1.3.6.1.4.1.2011.6.111.1.5.3.3.1.3	Unsigned32	read-create	A threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
U32 adsl2ChAlarmConfProfileAturThresh15MinCodingViolations	1.3.6.1.4.1.2011.6.111.1.5.3.3.1.4	Unsigned32	read-create	A threshold for the adsl2PMChCurr15MCodingViolations counter, when adsl2PMChCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
U32 adsl2ChAlarmConfProfileAturThresh15MinCorrected	1.3.6.1.4.1.2011.6.111.1.5.3.3.1.5	Unsigned32	read-create	A threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
U32 adsl2ChAlarmConfProfileMonitoringRateDs	1.3.6.1.4.1.2011.6.111.1.5.3.3.1.6	Unsigned32	read-create	The channel monitoring rate downstream.
U32 adsl2ChAlarmConfProfileMonitoringRateUs	1.3.6.1.4.1.2011.6.111.1.5.3.3.1.7	Unsigned32	read-create	The channel monitoring rate upstream.
ROW adsl2ChAlarmConfProfileRowStatus	1.3.6.1.4.1.2011.6.111.1.5.3.3.1.8	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must be first unreferenced from all associated templates.
adsl2Scalar	1.3.6.1.4.1.2011.6.111.1.6
adsl2ScalarSC	1.3.6.1.4.1.2011.6.111.1.6.1
U32 adsl2ScalarSCMaxInterfaces	1.3.6.1.4.1.2011.6.111.1.6.1.1	Unsigned32	read-only	This value determines the upper size of adsl2SCStatusTable. The maximum number of entries in adsl2SCStatusTable is equal to two times the value of this attribute.
U32 adsl2ScalarSCAvailInterfaces	1.3.6.1.4.1.2011.6.111.1.6.1.2	Unsigned32	read-only	This value determines the amount of space that is currently available in adsl2SCStatusTable. The number of entries available in adsl2SCStatusTable is equal to two times the value of this attribute.
adsl2Conformance	1.3.6.1.4.1.2011.6.111.1.8
adsl2Groups	1.3.6.1.4.1.2011.6.111.1.8.1
adsl2LineGroup	1.3.6.1.4.1.2011.6.111.1.8.1.1			The group of configuration, status, and commands objects on the line level.
adsl2ChannelStatusGroup	1.3.6.1.4.1.2011.6.111.1.8.1.2			The group of status objects on the channel level.
adsl2ChannelStatusAtmGroup	1.3.6.1.4.1.2011.6.111.1.8.1.3			The group of status objects on the data path level when it is ATM.
adsl2ChannelStatusPtmGroup	1.3.6.1.4.1.2011.6.111.1.8.1.4			The group of status objects on the data path level when it is PTM.
adsl2SCStatusGroup	1.3.6.1.4.1.2011.6.111.1.8.1.5			The group of status objects on the sub-carrier level. They are updated as a result of a DELT process.
adsl2LineInventoryGroup	1.3.6.1.4.1.2011.6.111.1.8.1.6			The group of inventory objects per xTU.
adsl2LineConfTemplateGroup	1.3.6.1.4.1.2011.6.111.1.8.1.7			The group of objects in a line configuration template.
adsl2LineConfProfGroup	1.3.6.1.4.1.2011.6.111.1.8.1.8			The group of objects in a line configuration profile.
adsl2LineConfProfRaGroup	1.3.6.1.4.1.2011.6.111.1.8.1.9			The group of objects required for controlling the rate adaptive behavior of the line.
adsl2LineConfProfMsgMinGroup	1.3.6.1.4.1.2011.6.111.1.8.1.10			The group of objects required for controlling the rate reserved for Overhead traffic.
adsl2LineConfProfModeSpecGroup	1.3.6.1.4.1.2011.6.111.1.8.1.11			The group of objects in a line configuration profile that have an instance for each operation mode allowed.
adsl2ChConfProfileGroup	1.3.6.1.4.1.2011.6.111.1.8.1.12			The group of objects in a channel configuration profile.
adsl2ChConfProfileAtmGroup	1.3.6.1.4.1.2011.6.111.1.8.1.13			The group of configuration objects required when the data path is ATM.
adsl2ChConfProfileMinResGroup	1.3.6.1.4.1.2011.6.111.1.8.1.14			The group of configuration objects required for the reserved data rate.
adsl2LineAlarmConfTemplateGroup	1.3.6.1.4.1.2011.6.111.1.8.1.15			The group of objects in a line alarm template.
adsl2LineAlarmConfProfileGroup	1.3.6.1.4.1.2011.6.111.1.8.1.16			The group of objects in a line alarm profile.
adsl2ChAlarmConfProfileGroup	1.3.6.1.4.1.2011.6.111.1.8.1.17			The group of objects in a channel alarm profile.
adsl2PMLineCurrGroup	1.3.6.1.4.1.2011.6.111.1.8.1.18			The group of objects that report the line level counters for current PM intervals.
adsl2PMLineCurrInitGroup	1.3.6.1.4.1.2011.6.111.1.8.1.19			The group of objects that report the full initializations counters for current PM intervals.
adsl2PMLineCurrInitShortGroup	1.3.6.1.4.1.2011.6.111.1.8.1.20			The group of objects that report the short initializations counters for current PM intervals.
adsl2PMLineHist15MinGroup	1.3.6.1.4.1.2011.6.111.1.8.1.21			The group of line level PM counters for the previous 15 minutes intervals.
adsl2PMLineHist1DayGroup	1.3.6.1.4.1.2011.6.111.1.8.1.22			The group of line level PM counters for the previous 24 hours intervals.
adsl2PMLineInitHist15MinGroup	1.3.6.1.4.1.2011.6.111.1.8.1.23			The group of PM counters for the previous 15 minutes intervals full initializations.
adsl2PMLineInitHist15MinShortGroup	1.3.6.1.4.1.2011.6.111.1.8.1.24			The group of PM counters for the previous 15 minutes intervals short initializations.
adsl2PMLineInitHist1DayGroup	1.3.6.1.4.1.2011.6.111.1.8.1.25			The group of PM counters for the previous 24 hours intervals full initializations.
adsl2PMLineInitHist1DayShortGroup	1.3.6.1.4.1.2011.6.111.1.8.1.26			The group of PM counters for the previous 24 hours intervals short initializations.
adsl2PMChCurrGroup	1.3.6.1.4.1.2011.6.111.1.8.1.27			The group of objects that report the channel level counters for current PM intervals.
adsl2PMChHist15MinGroup	1.3.6.1.4.1.2011.6.111.1.8.1.28			The group of objects that report the channel level counters for previous 15 minutes PM intervals.
adsl2PMChHist1DGroup	1.3.6.1.4.1.2011.6.111.1.8.1.29			The group of objects that report the channel level counters for previous 24 hours PM intervals.
adsl2ScalarSCGroup	1.3.6.1.4.1.2011.6.111.1.8.1.30			The group of objects that report the available memory resources for DELT processes.
adsl2ThreshNotificationGroup	1.3.6.1.4.1.2011.6.111.1.8.1.31			This group supports notifications of significant conditions associated with ADSL2 lines.
adsl2StatusChangeNotificationGroup	1.3.6.1.4.1.2011.6.111.1.8.1.32			This group supports notifications of thresholds crossing associated with ADSL2 lines.
adsl2Compliances	1.3.6.1.4.1.2011.6.111.1.8.2
adsl2LineMibCompliance	1.3.6.1.4.1.2011.6.111.1.8.2.1			The compliance statement for SNMP entities which manage ADSL2 interfaces.
adsl2Mode	1.3.6.1.4.1.2011.6.111.1.9
ADS hwadslmodecfg	1.3.6.1.4.1.2011.6.111.1.9.1	Adsl2CfgMode	read-write	This object is used to change ADSL management mode. After the mode being changed, system will automatically save data and reboot.

RFC description

Manages ADSL2/ADSL2+ lines with performance monitoring, configuration modes, power management, and line status tracking.

Start monitoring Huawei DSLAM/MSAN broadband access equipment (ADSL2/ADSL2+) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-ADSL2-LINE-MIB

What Is HUAWEI-ADSL2-LINE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description