DSG-IF-STD-MIB

All MIBs › DSG-IF-STD-MIB

Organization: Cable Television Laboratories, Inc.

Last Updated: 2017-06-15

Description: CableLabs MIB for DOCSIS Set-top Gateway tunnel, client, and classifier configuration on DOCSIS 2.0/3.0 cable networks

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DSG-IF-STD-MIB?

DSG-IF-STD-MIB is a CableLabs/DOCSIS standards MIB (vendor-neutral) defining managed objects for the DOCSIS Set-top Gateway (DSG) interface used to tunnel out-of-band messaging to cable set-top boxes over DOCSIS 2.0/3.0 cable plant. It exposes configuration and operational data for DSG tunnels, client identification, classification of downstream traffic into tunnels, and timeout/timer settings for the DSG channel sets (Tdsg1-Tdsg4). Its primary monitoring value is operational/configuration status rather than classic hardware faults: it lets an operator confirm the DSG mode a CMTS or cable modem is running in, verify DSG timer values, inspect the tunnel filter table that maps classifiers to DSG tunnels, and observe one-way recovery behavior when a device loses forward-path DSG signaling. It depends on the broader DOCSIS/CableLabs MIB family (e.g. DOCS-IF-MIB) and standard SNMP MIB-II conventions for the underlying interface table. It is deployed on CMTS headend equipment and DOCSIS cable modems/gateways, using the DSG-IF-STD-MIB reference in cable TV/broadband networks that carry set-top box control traffic in-band over DOCSIS.

IPNetwork Monitor allows you to monitor SNMP objects defined in DSG-IF-STD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral, standards-based MIB (CableLabs/DOCSIS)
applies to CMTS headend equipment and DOCSIS cable modems/set-top gateways

Monitoring Examples

An operator would read dsgIfStdDsgMode to confirm which DSG operational mode a device is running, and check dsgIfStdTdsg1 through dsgIfStdTdsg4 (with their paired Timeouts objects) to verify the DSG timer configuration matches the CMTS. Walking dsgIfStdTunnelFilterTable/dsgIfStdTunnelFilterEntry shows how downstream classifiers map to specific DSG tunnels, letting an admin confirm set-top traffic is being routed to the correct tunnel. The dsgIfStdOneWayRecovery object indicates whether a device is operating in one-way (forward-path-only) recovery mode, which would reveal a return-path signaling problem, and dsgIfStdNotifications would alert on related state changes.

What Can Be Monitored

DSG operational mode
DSG timer values (Tdsg1-Tdsg4)
tunnel-to-classifier mapping
one-way recovery status
DSG notification/trap events

Imported Objects

From CLAB-DEF-MIB

clabProjDocsis

OBJECT-IDENTITY

From DOCS-CABLE-DEVICE-MIB

docsDevEvId	OBJECT-TYPE
docsDevEvLevel	OBJECT-TYPE
docsDevEvText	OBJECT-TYPE

From DOCS-IF-MIB

docsIfCmCmtsAddress	OBJECT-TYPE
docsIfCmStatusDocsisOperMode	OBJECT-TYPE
docsIfCmStatusModulationType	OBJECT-TYPE
docsIfDocsisBaseCapability	OBJECT-TYPE

From DOCS-IF3-MIB

Dsid

From IF-MIB

ifPhysAddress

OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressPrefixLength
InetAddressType
InetPortNumber

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
TruthValue

How to Use in IPNetwork Monitor

Example using dsgIfStdTdsg1Timeouts OID:

Select a CMTS/DOCSIS cable modem-gateway (Set-top Gateway tunnel, vendor-neutral CableLabs standard) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type dsgIfStdTdsg1Timeouts into the Find box to locate it in the OID tree, then select it and click OK. The number of times Tdsg1 expired in the DSG eCM since last reboot. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
dsgIfStdMib	1.3.6.1.4.1.4491.2.1.4			Licensed under the Apache License, Version 2.0 (the 'License'); you may not use this file except in compliance with the License. You may obtain a copy of the License at: http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an 'AS IS' BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. This MIB module provides the management objects of the DOCSIS Set-top Gateway (DSG) client controller CM component for DSG operations of Set-top devices. Copyright 1999-2017 Cable Television Laboratories, Inc. All rights reserved.
dsgIfStdNotifications	1.3.6.1.4.1.4491.2.1.4.0
NTF dsgIfStdUpstreamEnabledNotify	1.3.6.1.4.1.4491.2.1.4.0.1			Indicates the eCM is being instructed to have the upstream transmitter enabled. This notification is send after CM registration. Note that the objects docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode and docsIfCmStatusModulationType may not be supported in some situations (e.g., for 1.1 CMs in 1.0 mode these objects are optional, for 3.0 CMs docsIfCmStatusDocsisOperMode and docsIfCmStatusModulationType are deprecated). If that is the case, the above varbind objects are indicated as noSuchName or noSuchObject for SNMPv1 and SNMPv2 notification PDUs respectively.
NTF dsgIfStdUpstreamDisabledNotify	1.3.6.1.4.1.4491.2.1.4.0.2			Indicates the CM is being instructed to have the upstream transmitter disabled. This notification is only send when the CM is registered and prior to disable the upstream transmitter. Note that the objects docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode and docsIfCmStatusModulationType may not be supported in some situations (e.g., for 1.1 CMs in 1.0 mode these objects are optional, for 3.0 CMs docsIfCmStatusDocsisOperMode and docsIfCmStatusModulationType are deprecated). If that is the case the above varbind objects are indicated as noSuchName or noSuchObject for SNMPv1 and SNMPv2 notification PDUs respectively.
NTF dsgIfStdTdsg2TimeoutNotify	1.3.6.1.4.1.4491.2.1.4.0.3			Notifies that the eCM has a timeout Tdsg2. Note that the objects docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode and docsIfCmStatusModulationType may not be supported in some situations (e.g., for 1.1 CMs in 1.0 mode these objects are optional, for 3.0 CMs docsIfCmStatusDocsisOperMode and docsIfCmStatusModulationType are deprecated). If that is the case the above varbind objects are indicated as noSuchName or noSuchObject for SNMPv1 and SNMPv2 notification PDUs respectively.
dsgIfStdMibObjects	1.3.6.1.4.1.4491.2.1.4.1
dsgIfStdConfig	1.3.6.1.4.1.4491.2.1.4.1.1
INT dsgIfStdDsgMode	1.3.6.1.4.1.4491.2.1.4.1.1.1	INTEGER	read-only	The DSG Mode of operation of this device. The value 'none' indicates that the eCM is not performing DSG operations.
U32 dsgIfStdTdsg1	1.3.6.1.4.1.4491.2.1.4.1.1.2	Unsigned32	read-only	The configured value for the Tdsg1 timer.
U32 dsgIfStdTdsg2	1.3.6.1.4.1.4491.2.1.4.1.1.3	Unsigned32	read-only	The configured value for the Tdsg2 timer.
U32 dsgIfStdTdsg3	1.3.6.1.4.1.4491.2.1.4.1.1.4	Unsigned32	read-only	The configured value for the Tdsg3 timer.
U32 dsgIfStdTdsg4	1.3.6.1.4.1.4491.2.1.4.1.1.5	Unsigned32	read-only	The configured value for the Tdsg4 timer.
C32 dsgIfStdTdsg1TimeoutsEx	1.3.6.1.4.1.4491.2.1.4.1.1.6	Counter32	read-only	The number of times Tdsg1 expired in the DSG eCM since last reboot.
C32 dsgIfStdTdsg2Timeouts	1.3.6.1.4.1.4491.2.1.4.1.1.7	Counter32	read-only	The number of times Tdsg2 expired in the DSG eCM since last reboot.
C32 dsgIfStdTdsg3Timeouts	1.3.6.1.4.1.4491.2.1.4.1.1.8	Counter32	read-only	The number of times Tdsg3 expired in the DSG eCM since last reboot.
C32 dsgIfStdTdsg4Timeouts	1.3.6.1.4.1.4491.2.1.4.1.1.9	Counter32	read-only	The number of times Tdsg4 expired in the DSG eCM since last reboot.
INT dsgIfStdOneWayRecovery	1.3.6.1.4.1.4491.2.1.4.1.1.10	INTEGER	read-write	This objects describes what the eCM does when the Tdsg3 timer expires. A value of retryUp(1) indicates that the eCM will remain on the current downstream channel(s) and will attempt to re-establish the upstream. A value of scan(2) indicates that the eCM will scan for new downstream channel(s). The value of the object is retained in nonvolatile storage.
dsgIfStdTunnelFilter	1.3.6.1.4.1.4491.2.1.4.1.2
dsgIfStdTunnelFilterTable	1.3.6.1.4.1.4491.2.1.4.1.2.1		not-accessible	A table of the active DSG Tunnel Filters. Each DSG Tunnel Filter is used to identify packets to forward to a DSG Client. Conceptually, each DSG Tunnel is composed of one or more DSG tunnel filters.
dsgIfStdTunnelFilterEntry	1.3.6.1.4.1.4491.2.1.4.1.2.1.1		not-accessible	The DSG eCM will have one entry for each DSG Tunnel Filter. One or more entries in this table are created when the DSG Client Controller instructs the eCM to begin forwarding traffic from a particular DSG Tunnel. When the Client Controller instructs the eCM that traffic from a DSG Tunnel should no longer be forwarded, the eCM deletes corresponding entries from this table. Note that a DSG Tunnel Filter is constructed by the DSG Client Controller using an unspecified algorithm and based on information in the DCD. Statistics like the packet and octet counts apply to the DSG Tunnel Filter and not necessarily to a DSG Rule.
U32 dsgIfStdTunnelFilterIndex	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.1	Unsigned32	not-accessible	The unique index of entries in this table.
I32 dsgIfStdTunnelFilterApplicationId	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.2	Integer32	read-only	The Application ID of the DSG Tunnel associated with this DSG Tunnel Filter. This object returns -1 for: DSG Tunnels that do not have an associated Application ID or for DSG Tunnels for which the Application ID is unknown. In an OpenCable Host, this object returns '0' for a DSG Tunnel whose client resides on the Card. This object has been replaced by the dsgIfStdTunnelFilterClientIdType and dsgIfStdTunnelFilterClientIdValue objects.
MAC dsgIfStdTunnelFilterMacAddress	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.3	MacAddress	read-only	The destination MAC Address matching this DSG Tunnel Filter entry.
IPt dsgIfStdTunnelFilterIpAddressType	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.4	InetAddressType	read-only	The type of InetAddress for dsgIfStdTunnelFilterSrcIpAddr, dsgIfStdTunnelFilterSrcIpMask and dsgIfStdTunnelFilterDestIpAddr. Currently DSG Agents, DSG Client Controllers and DSG eCMs are not required to support IPv6 DSG classifiers.
IP dsgIfStdTunnelFilterSrcIpAddr	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.5	InetAddress	read-only	The source IP Address matching this DSG Tunnel Filter. This object is used in conjunction with dsgIfStdTunnelFilterSrcMask. A value of zero indicates that source IP Address filtering does not apply. The type of this address is determined by the value of the dsgIfStdTunnelFilterIpAddressType object.
IP dsgIfStdTunnelFilterSrcIpMask	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.6	InetAddress	read-only	The Source IP Mask to be used with dsgIfStdTunnelFilterSrcIpAddr when comparing a packet to this DSG Tunnel Filter. The type of this address is determined by the value of the dsgIfStdTunnelFilterIpAddressType object.
IP dsgIfStdTunnelFilterDestIpAddr	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.7	InetAddress	read-only	The destination IP Address matching this DSG Tunnel Filter. A value of zero indicates that destination IP Address filtering does not apply. The type of this address is determined by the value of the dsgIfStdTunnelFilterIpAddressType object.
INE dsgIfStdTunnelFilterDestPortStart	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.8	InetPortNumber	read-only	The lower UDP destination port value in the range matching this DSG Tunnel Filter.
INE dsgIfStdTunnelFilterDestPortEnd	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.9	InetPortNumber	read-only	The upper UDP destination port value in the range matching this DSG Tunnel Filter.
C32 dsgIfStdTunnelFilterPkts	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.10	Counter32	read-only	The total number of Packets matching this DSG Tunnel Filter entry since creation of the entry.
C32 dsgIfStdTunnelFilterOctets	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.11	Counter32	read-only	The total number of octets matching this DSG Tunnel Filter entry since creation of the entry.
C32 dsgIfStdTunnelFilterTimeActive	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.12	Counter32	read-only	The total number of seconds that this DSG Tunnel Filter entry has been instantiated.
U32 dsgIfStdTunnelFilterTunnelId	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.13	Unsigned32	read-only	In DSG Advanced Mode, this value identifies the DSG Tunnel corresponding to this DSG Tunnel Filter entry. This value may correspond to the DSG Rule ID from the DCD message.
DSI dsgIfStdTunnelFilterDsid	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.14	Dsid	read-only	When operating with Multicast DSID Forwarding (MDF) enabled, this object contains the DSID value obtained from the DA-to-DSID TLV in the MDD. If no DSID has been advertised for this tunnel MAC address then this object returns 0. When MDF is disabled, this object returns 0. Pre-3.0 DOCSIS devices are not required to instantiate this object.
INT dsgIfStdTunnelFilterClientIdType	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.15	INTEGER	read-only	The value of cableCard(0) indicates a DSG Tunnel requested by the CableCARD on an OpenCable Host. The value of broadcast(1) indicates a DSG Tunnel for an industry standard flow identified by a DSG Broadcast ID. The value of macAddress(2) indicates a DSG Tunnel for a flow identified by a well known MAC Address. The value of caSystemId(3) indicates a DSG Tunnel for a flow identified by a CA_system_ID. The value of applicationId(4) indicates a DSG Tunnel identified by an application ID.
OCT dsgIfStdTunnelFilterClientIdValue	1.3.6.1.4.1.4491.2.1.4.1.2.1.1.16	OCTET STRING	read-only	The Client Identification Value. The content depends on the value of the dsgIfStdTunnelFilterClientIdType. For dsgIfStdTunnelFilterClientIdType of type cableCard(0), this object will return a zero length string. For dsgIfStdTunnelFilterClientIdType of a type broadcast(1), this object will have a 16-bit value whether or not it is a length 0 or length 2 broadcast ID. If the value is 0, then the encoded TLV in the DCD would be the original, zero length, broadcast ID. If the value is specified in Table 5-2, then the TLV in the DCD would be a length 2 broadcast ID followed by the value. For dsgIfStdTunnelFilterClientIdType of type macAddress(2), this object will return a well known MAC address. For dsgIfStdTunnelFilterClientIdType of type caSystemId(3), this object will return a CA System ID. For dsgIfStdTunnelFilterClientIdType of type applicationId(4), this object will return an application ID. Client IDs representing types broadcast(1), caSystemId(3) or applicationId(4) are encoded in DCD messages as Unsigned integers and configured in this object as 6 octet string with the 2 LSB for the client ID value, e.g., an applicationId 2048 (0x0800) is encoded as '000000000800'h.
dsgIfStdDsgChannelList	1.3.6.1.4.1.4491.2.1.4.1.3
dsgIfStdDsgChannelListTable	1.3.6.1.4.1.4491.2.1.4.1.3.1		not-accessible	This table contains the list of DSG channels provided to the DSG eCM for use in scanning.
dsgIfStdDsgChannelListEntry	1.3.6.1.4.1.4491.2.1.4.1.3.1.1		not-accessible	The conceptual row for this table. The DSG eCM creates an entry per each downstream channel provided in the DCD message. An entry is deleted when removed from the DCD message.
U32 dsgIfStdDsgChannelListIndex	1.3.6.1.4.1.4491.2.1.4.1.3.1.1.1	Unsigned32	not-accessible	The unique identifier for entries in this table
U32 dsgIfStdDsgChannelListFrequency	1.3.6.1.4.1.4491.2.1.4.1.3.1.1.2	Unsigned32	read-only	The downstream channel center frequency of this entry.
dsgIfStdDsgSeb	1.3.6.1.4.1.4491.2.1.4.1.4
T/F dsgIfStdDsgSebControlObject	1.3.6.1.4.1.4491.2.1.4.1.4.1	TruthValue	read-write	This object controls the state of DSG SEB. When set to FALSE the device is prohibited from enabling DSG SEB, both as a client or a server.
INT dsgIfStdDsgSebRole	1.3.6.1.4.1.4491.2.1.4.1.4.2	INTEGER	read-only	This object reports the current role of this device. The value of disabled(1) is used for a device where SEB is administratively disabled. The value of sebServerIneligible(2) is used for a device that is two-way operational but is not eligible to act as a SEB Server. The value of sebServerNoClients(3) represents a device that is two-way operational and is eligible to act as a server, but does not have any clients. The value of sebServerWithClients(4) represents a SEB Server with at least one established SEB Tunnel. The value of sebClientNoTunnel(5) represents a one-way device that has not established a SEB Tunnel. The value of sebClientWithTunnel(6) represents a one-way device that has successfully established a SEB Tunnel. The value of attemptingTwoWay(7) is used when a device is in the process of establishing DOCSIS upstream connectivity.
U32 dsgIfStdDsgSebFomWeightUpstreamPower	1.3.6.1.4.1.4491.2.1.4.1.4.3	Unsigned32	read-write	This object controls the contribution of the upstream transmit power level term for the Figure of Merit Calculation.
U32 dsgIfStdDsgSebFomWeightDownstreamPower	1.3.6.1.4.1.4491.2.1.4.1.4.4	Unsigned32	read-write	This object controls the contribution of the downstream receive power level term for the Figure of Merit Calculation.
U32 dsgIfStdDsgSebFomWeightEqualizer	1.3.6.1.4.1.4491.2.1.4.1.4.5	Unsigned32	read-write	This object controls the contribution of the equalizer performance term for the Figure of Merit Calculation.
U32 dsgIfStdDsgSebFomUsPwrHr	1.3.6.1.4.1.4491.2.1.4.1.4.6	Unsigned32	read-write	This object defines the Upstream transmit power headroom value for the Figure of Merit Calculation.
U32 dsgIfStdDsgSebFomMfQpsk	1.3.6.1.4.1.4491.2.1.4.1.4.7	Unsigned32	read-write	This object defines the value of maximum power level for QPSK upstream for the Figure of Merit Calculation.
U32 dsgIfStdDsgSebFomMfQam16	1.3.6.1.4.1.4491.2.1.4.1.4.8	Unsigned32	read-write	This object defines the value of maximum power level for QAM16 upstream for the Figure of Merit Calculation.
U32 dsgIfStdDsgSebFomMfQam64	1.3.6.1.4.1.4491.2.1.4.1.4.9	Unsigned32	read-write	This object defines the value of maximum power level for QAM64 upstream for the Figure of Merit Calculation.
I32 dsgIfStdDsgSebFomDsDesPwr	1.3.6.1.4.1.4491.2.1.4.1.4.10	Integer32	read-write	This object defines the value of desired downstream receive power for the Figure of Merit Calculation.
I32 dsgIfStdDsgSebFomDspMin	1.3.6.1.4.1.4491.2.1.4.1.4.11	Integer32	read-write	This object defines the value of downstream receive power minimum for the Figure of Merit Calculation.
I32 dsgIfStdDsgSebFomDspMax	1.3.6.1.4.1.4491.2.1.4.1.4.12	Integer32	read-write	This object defines the value of downstream receive power maximum for the Figure of Merit Calculation.
U32 dsgIfStdDsgSebFomNmteRng	1.3.6.1.4.1.4491.2.1.4.1.4.13	Unsigned32	read-write	This object defines the value of non-main tap energy range for the Figure of Merit Calculation.
I32 dsgIfStdDsgSebFomNmteMax	1.3.6.1.4.1.4491.2.1.4.1.4.14	Integer32	read-write	This object defines the value of non-main tap energy maximum for the Figure of Merit Calculation.
I32 dsgIfStdDsgSebFomMtcMin	1.3.6.1.4.1.4491.2.1.4.1.4.15	Integer32	read-write	This object defines the value of main tap compression minimum for the Figure of Merit Calculation.
U32 dsgIfStdDsgSebFom	1.3.6.1.4.1.4491.2.1.4.1.4.16	Unsigned32	read-only	This object contains the value resulting from the FOM calculation.
U32 dsgIfStdDsgSebTunnelTimeout	1.3.6.1.4.1.4491.2.1.4.1.4.17	Unsigned32	read-write	The number of seconds the SEB Server will wait for the SEB Tunnel to be established by the SEBC after receiving the ClientConnect service action.
I32 dsgIfStdDsgSebTdsg3Override	1.3.6.1.4.1.4491.2.1.4.1.4.18	Integer32	read-write	This object overrides the value of the Tdsg3 timeout specified in the DCD. A value of -1 indicates that the DCD value will be used. This object is ignored when dsgIfStdDsgSebControlObject is set to false.
dsgIfStdDsgSebConnectedDeviceTable	1.3.6.1.4.1.4491.2.1.4.1.4.19		not-accessible	For a SEB Server, a list of the connected devices. In general, each SEB Tunnel will be used for multiple devices and will therefore have multiple entries in this table. For a SEB Client, a list of devices contained within the client utilizing the SEB service.
dsgIfStdDsgSebConnectedDeviceEntry	1.3.6.1.4.1.4491.2.1.4.1.4.19.1		not-accessible	The conceptual row of dsgIfStdDsgSebConnectedDeviceTable.
U32 dsgIfStdDsgSebConnectedDeviceIndex	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.1	Unsigned32	not-accessible	The unique identifier for entries in this table
MAC dsgIfStdDsgSebConnectedDeviceMacAddress	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.2	MacAddress	read-only	MAC Address of the connected device.
IPt dsgIfStdDsgSebConnectedDeviceIpAddressType	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.3	InetAddressType	read-only	Type of IP Address for dsgIfStdDsgSebConnectedDeviceIpAddress.
IP dsgIfStdDsgSebConnectedDeviceIpAddress	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.4	InetAddress	read-only	Global IP address assigned by a DHCP server and used on the DOCSIS network for this device. This object will report 0.0.0.0 if no address has been assigned or if the address is unknown. Note that the SEB Server will not generally know the DHCP-assigned addresses of the connected devices and will populate this object as 0.0.0.0.
INT dsgIfStdDsgSebConnectedDeviceType	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.5	INTEGER	read-only	Type of device. Type cableCard(2) has been deprecated.
IPt dsgIfStdDsgSebTunnelClientIpAddressType	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.6	InetAddressType	read-only	This object specifies the IP address type of dsgIfStdDsgSebTunnelClientIpAddress.
IP dsgIfStdDsgSebTunnelClientIpAddress	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.7	InetAddress	read-only	The client side IP address of the SEB Tunnel. If a SEB Tunnel is not established, this object will report 0.0.0.0.
U32 dsgIfStdDsgSebTunnelClientPort	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.8	Unsigned32	read-only	The server side TCP port used by this tunnel. If a SEB Tunnel is not established, this object will report 0.
IPt dsgIfStdDsgSebTunnelServerIpAddressType	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.9	InetAddressType	read-only	This object specifies the IP address type of dsgIfStdDsgSebTunnelServerIpAddress.
IP dsgIfStdDsgSebTunnelServerIpAddress	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.10	InetAddress	read-only	The server side IP address of the SEB Tunnel. If a SEB Tunnel is not established, this object will report 0.0.0.0.
U32 dsgIfStdDsgSebTunnelServerPort	1.3.6.1.4.1.4491.2.1.4.1.4.19.1.11	Unsigned32	read-only	The server side TCP port used by this tunnel. If a SEB Tunnel is not established, this object will report 0.
dsgIfStdConformance	1.3.6.1.4.1.4491.2.1.4.2
dsgIfStdCompliances	1.3.6.1.4.1.4491.2.1.4.2.1
dsgIfStdBasicCompliance	1.3.6.1.4.1.4491.2.1.4.2.1.1			The compliance statement for DOCSIS Set-top Gateway eCMs.
dsgIfStdDsgSebCompliance	1.3.6.1.4.1.4491.2.1.4.2.1.2			The compliance statement for DOCSIS Set-top Gateway devices that support DSG SEB.
dsgIfStdGroups	1.3.6.1.4.1.4491.2.1.4.2.2
dsgIfStdConfigGroup	1.3.6.1.4.1.4491.2.1.4.2.2.1			A collection of configuration elements provided in DCD messages and DSG operations.
dsgIfStdNotifyGroup	1.3.6.1.4.1.4491.2.1.4.2.2.2			The collection of DSG notifications that the eCM reports as part of the Set-top device
dsgIfStdDsgSebGroup	1.3.6.1.4.1.4491.2.1.4.2.2.3			A collection of configuration elements in support of DSG SEB operation. These objects are required for both clients and servers.

RFC description

DOCSIS Set-top Gateway interface standard for cable set-top device management.

Start monitoring CMTS/DOCSIS cable modem-gateway (Set-top Gateway tunnel, vendor-neutral CableLabs standard) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DSG-IF-STD-MIB