HPN-ICF-DOT11-CFG-MIB

All MIBs › HPN-ICF-DOT11-CFG-MIB

Last Updated: 2010-09-25

Category: Technology: Wireless, Vendor: H3C/HH3C, Vendor: HP/HPE, Wireless and WLAN

Description: HP Networking ICF SNMP MIB for 802.11 wireless SSID, radio, and basic WLAN configuration on HP wireless networking devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-DOT11-CFG-MIB?

HPN-ICF-DOT11-CFG-MIB is an H3C/HPE Networking (ICF) proprietary MIB configuring WLAN controller-wide 802.11 behavior. Its objects cover global country code, station keepalive/idle timer intervals, broadcast-probe-reply flag, AP scan mode, AC control/data-tunnel security-support flags, auto-AP support/name, persistent naming, interface-trap threshold, monitor/sample intervals, channel-switch-check interval, per-AP user uplimit, AP Layer-2-isolation enable, AP BSSID-support count, DoS-protection enable, max APs per interface, and uplink-tracking/route-collection settings. As a configuration MIB it lets an administrator confirm global WLAN capacity and security settings on an H3C/HPE ICF wireless controller. It is deployed on H3C/HPE Networking (ICF-based) wireless controllers. Engineers can download the HPN-ICF-DOT11-CFG-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-DOT11-CFG-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C/HPE Networking (ICF-based) wireless controllers

Monitoring Examples

An administrator checks hpnicfDot11APUserUplimit and hpnicfDot11APDoSProtectEnable to confirm per-AP capacity and DoS protection settings on an H3C/HPE ICF wireless controller.

What Can Be Monitored

global WLAN capacity and security configuration

Imported Objects

From HPN-ICF-DOT11-REF-MIB

HpnicfDot11AuthenType
HpnicfDot11ChannelScopeType
HpnicfDot11CirMode
HpnicfDot11ObjectIDType
HpnicfDot11PreambleType
HpnicfDot11RadioElementIndex
HpnicfDot11RadioScopeType
HpnicfDot11RadioType
HpnicfDot11RadioType2
HpnicfDot11SSIDEncryptModeType
HpnicfDot11SSIDStringType
HpnicfDot11SecIEStatusType
HpnicfDot11ServicePolicyIDType
HpnicfDot11TruthValueCM
HpnicfDot11TunnelSecSchemType
HpnicfDot11TxPwrLevelScopeType
HpnicfDot11WorkMode
hpnicfDot11	MODULE-IDENTITY
hpnicfDot11APElementIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress

From RFC1213-MIB

ifIndex

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfDot11CFG	1.3.6.1.4.1.11.2.14.11.15.2.75.4			This MIB provides information about WLAN configuration. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC. Fit AP Applied in the enterprise environment, it will work under the control and management from AC. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP. Radio The chip set to receive and send wireless signal. Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.) Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association. MSDU MAC Service Data Unit, it is frame format defined by 802.11. TU It is 1,024 microseconds (ms), which is about 1 millisecond. AKM The authentication and key management method defined by 802.11i, and which includes 802.1x and pre-shared key.
hpnicfDot11GlobeConfigGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1
OCT hpnicfDot11GlobalCountryCode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.1	OCTET STRING	read-write	Represents the country code for wireless network.
U32 hpnicfDot11StaKeepALiveTimerIntvl	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.2	Unsigned32	read-write	Represents the interval of the keep alive requests sent between AP and STA. Default value 0 : The keep alive function is disabled.
I32 hpnicfDot11StaIdleTimerIntvl	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.3	Integer32	read-write	Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
T/F hpnicfDot11BroadcastProbeReply	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.4	TruthValue	read-write	Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
INT hpnicfDot11APScanMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.5	INTEGER	read-write	Represents the scanning mode for AP. The following values are supported: active - AP will actively do scan. passive - AP will passively do scan.
HPN hpnicfDot11ACCtrlTunnelSecSupport	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.6	HpnicfDot11TunnelSecSchemType	read-write	Represents what security schemes are supported for CAPWAP Control tunnel.
HPN hpnicfDot11ACDataTunnelSecSupport	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.7	HpnicfDot11TunnelSecSchemType	read-write	Represents what security schemes are supported for CAPWAP data tunnel. The cleartxt is the default scheme.
T/F hpnicfDot11ACAutoAPSupport	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.8	TruthValue	read-write	Represents enable the auto AP functionality or not. 'true' : The auto AP functionality is enabled. 'false': The auto AP functionality is disabled
OCT hpnicfDot11AutoAPName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.9	OCTET STRING	read-write	Represents the name of auto AP that needs to be made persistent. When read the value from the node, NULL value be returned.
OCT hpnicfDot11PersistentName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.10	OCTET STRING	read-write	Represents the new name of auto AP after being made persistent. When read the value from the node, NULL value be returned.
I32 hpnicfDot11IntfTrapThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.11	Integer32	read-write	Represents threshold of interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
U32 hpnicfDot11MonitorInterval	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.12	Unsigned32	read-write	Represents the monitoring interval. Default value 0 : The monitoring functionality is changed to real-time mode.
U32 hpnicfDot11SampleInterval	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.13	Unsigned32	read-write	Represents the sampling interval. Default value 0 : The sampling functionality is disabled.
U32 hpnicfDot11ChnlSwitChkInterval	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.14	Unsigned32	read-write	Represents the checking interval of channel switch.
U32 hpnicfDot11APUserUplimit	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.15	Unsigned32	read-write	Represents the upper limit of user which has access to this AP.
T/F hpnicfDot11APL2IsolateEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.16	TruthValue	read-write	Represents enable the layer2 isolation or not. 'true' : The layer2 isolation functionality is enabled. 'false': The layer2 isolation functionality is disabled.
I32 hpnicfDot11APBSSIDSupportNum	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.17	Integer32	read-only	Represents the max number of BSSID supported by Current AP.
DAT hpnicfDot11APLastUpdateStatTime	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.18	DateAndTime	read-only	Represents date and time update statistic information lately.
T/F hpnicfDot11APDoSProtectEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.19	TruthValue	read-write	Represents enable the DOS protection or not. 'true' : The DOS protection functionality is enabled. 'false': The DOS protection functionality is disabled.
U32 hpnicfDot11MaxAPPerIf	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.20	Unsigned32	read-write	Represents max AP number that can be connected to AC interface.
DAT hpnicfDot11SampleTimeStamp	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.21	DateAndTime	read-only	Represents the start time of current sample period.
U32 hpnicfDot11UplinkTrackId	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.22	Unsigned32	read-write	Represents the track id of AP. Default value 0 : The uplink track function for AP is disabled.
T/F hpnicfDot11RtCollectSwitch	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.23	TruthValue	read-write	This object is used to turn on/off real-time statistics collection between AC and AP. If the value is true, hpnicfDot11RtCollectIntvl will take effect. Otherwise, hpnicfDot11RglCollectIntvl will take effect.
I32 hpnicfDot11RglCollectIntvl	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.24	Integer32	read-write	This object represents interval to regularly collect statistics from AC to AP.
I32 hpnicfDot11RtCollectIntvl	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.25	Integer32	read-write	This object represents interval to collect real-time statistics from AC to AP.
I32 hpnicfDot11AllAPCpuUsageThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.26	Integer32	read-write	The CPU usage threshold for all AP.
I32 hpnicfDot11AllAPMemUsageThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.27	Integer32	read-write	The memory usage threshold for all AP.
I32 hpnicfDot11AdjIntfTrapThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.28	Integer32	read-write	Represents threshold of adjacent interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
INT hpnicfDot11AllAPMonitorMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.29	INTEGER	read-write	Represents what work mode for All AP. The following values are supported: normal, - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
INT hpnicfDot11GlobalApFmwUpdState	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.30	INTEGER	read-write	Represents the status of version auto-update for an AP. The following values are supported: enable - AP version will be updated automatically. disable - AP version will not be updated automatically.
OCT hpnicfDot11ACNasIDCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.31	OCTET STRING	read-write	Represents the NAS-ID of current AC.
hpnicfDot11PolicyConfigGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2
hpnicfDot11RadioPolicyTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1		not-accessible	The table defines the parameters for radio policy, as per radio policy of CLI. One radio policy could be assigned to the different radios (AP).
hpnicfDot11RadioPolicyEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1		not-accessible	Each entry contains information of each radio policy.
OCT hpnicfDot11RadioPolicyName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.1	OCTET STRING	not-accessible	Represents the name of radio policy.
I32 hpnicfDot11BeaconInterval	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.2	Integer32	read-create	Represents the interval for Beacon management frame.
I32 hpnicfDot11DtimInterval	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.3	Integer32	read-create	Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
I32 hpnicfDot11RtsThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.4	Integer32	read-create	Represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
I32 hpnicfDot11FragThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.5	Integer32	read-create	Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
I32 hpnicfDot11ShortRetryThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.6	Integer32	read-create	Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RTSThreshold, which shall be made before a failure condition is indicated.
I32 hpnicfDot11LongRetryThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.7	Integer32	read-create	Represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RTSThreshold, that shall be made before a failure condition is indicated.
U32 hpnicfDot11MaxRxLifetime	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.8	Unsigned32	read-create	Represents the elapsed time. After the time specified by hpnicfDot11MaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated.
ROW hpnicfDot11RdoPolicyRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.9	RowStatus	read-create	The status of this table entry.
I32 hpnicfDot11RdoClientMaxCount	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.10	Integer32	read-create	Represent the maximum number of stations supported by this radio policy.
I32 hpnicfDot11BeaconIntervalMs	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.11	Integer32	read-create	Represents the interval for Beacon management frame.
hpnicfDot11ServicePolicyTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2		not-accessible	The table defines the parameters for ESS, as per service policy of CLI. One service policy could be assigned to the different radios (AP).
hpnicfDot11ServicePolicyEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1		not-accessible	Each entry contains information of each service policy.
HPN hpnicfDot11ServicePolicyID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.1	HpnicfDot11ServicePolicyIDType	not-accessible	Represents the ID of each service policy.
STR hpnicfDot11SSIDName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.2	HpnicfDot11SSIDStringType	read-create	Represents the ESS. As per CLI, the value of service policy name will be SSID.
T/F hpnicfDot11SSIDHidden	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.3	TruthValue	read-create	This attribute controls whether the SSID will be advertised in the beacon frame. If it is true, then SSID will not be advertised in the beacon frame.
HPN hpnicfDot11AuthenMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.4	HpnicfDot11AuthenType	read-create	Represents the Authentication mode defined by 802.11.
HPN hpnicfDot11SSIDEncryptionMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.5	HpnicfDot11SSIDEncryptModeType	read-create	Represents the encryption mode for this ESS.
OCT hpnicfDot11WlanInfBindingType	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.6	OCTET STRING	read-create	Represents the service policy will bind to what kind of data forwarding interface.
I32 hpnicfDot11WlanInfBindingID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.7	Integer32	read-create	Represents the interface ID of the interface that ESS will bind to. If the value is set to -1, the binding will be removed.
ROW hpnicfDot11SrvPolicyRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.8	RowStatus	read-create	The status of this table entry.
I32 hpnicfDot11ClientMaxCount	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.9	Integer32	read-create	Represent the maximum number of stations supported by this service policy.
HPN hpnicfDot11SPInCirMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.10	HpnicfDot11CirMode	read-create	CIR(committed information rate) mode of inbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset.
I32 hpnicfDot11SPInCirValue	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.11	Integer32	read-create	Represents the CIR of inbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
HPN hpnicfDot11SPOutCirMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.12	HpnicfDot11CirMode	read-create	CIR(committed information rate) mode of outbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset.
I32 hpnicfDot11SPOutCirValue	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.13	Integer32	read-create	Represents the CIR of outbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
I32 hpnicfDot11WlanInfPVID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.14	Integer32	read-create	Represents the VLAN ID of SSID.
I32 hpnicfDot11SPInCirStaticValue	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.15	Integer32	read-create	Represents the CIR of inbound direction for static CIR mode.
I32 hpnicfDot11SPOutCirStaticValue	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.16	Integer32	read-create	Represents the CIR of outbound direction for static CIR mode.
T/F hpnicfDot11SPIsolate	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.17	TruthValue	read-create	If it is true, then stations connected with the service policy are isolated.
IP hpnicfDot11WlanexAuthServerIP	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.18	IpAddress	read-create	Represents the IP address of the Wlanex Authentication server
T/F hpnicfDot11SPBeaconMeasEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.19	TruthValue	read-create	If it is true, then beacon-measurement is enabled.
INT hpnicfDot11SPBeaconMeasType	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.20	INTEGER	read-create	Represents what the work mode for BeaconMeasurement type. The following values are supported: passive, - BeaconMeasurement will use the passive type. active - BeaconMeasurement will use the active type. beaconTable - BeaconMeasurement will use the beacon table type.
I32 hpnicfDot11SPBeaconMeasInterval	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.21	Integer32	read-create	Represents the beacon-measurement interval.
INT hpnicfDot11AuthenModeCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.22	INTEGER	read-create	Represents the Authentication mode defined by 802.11.
INT hpnicfDot11SecIEStatusCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.23	INTEGER	read-create	To enable the security Information element in the beacon and probe response frames sent by AP.
INT hpnicfDot11SecurityCiphersCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.24	INTEGER	read-create	The WLAN system support the following cipher type for data frame encryption. none wep40 wep104 tkip aesccmp wpi-SMS4 When the value of node equals to zero, it means no configuration or undo operation.
INT hpnicfDot11SrvPolicyStatusCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.25	INTEGER	read-create	The status of the Service Policy.
HPN hpnicfDot11SSIDHiddenCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.26	HpnicfDot11TruthValueCM	read-create	This attribute controls whether the SSID will be advertised in beacon frames. If it is dot11true, the SSID will not be advertised in beacon frames.
HPN hpnicfDot11SPIsolateCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.27	HpnicfDot11TruthValueCM	read-create	If it is dot11true, the clients connected with the service policy are isolated to each other.
hpnicfDot11ServicePolicyExtTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3		not-accessible	The table defines the parameters for ESS, as per service policy of CLI. When the value of hpnicfDot11SSIDEncryptionMode equals to cipher(2), more configuration for a ESS will be put into the table.
hpnicfDot11ServicePolicyExtEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1		not-accessible	Each entry contains information of each service policy under cipher(2) mode.
HPN hpnicfDot11ServicePolicyExtID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.1	HpnicfDot11ServicePolicyIDType	not-accessible	Represents the ID of each service policy.
HPN hpnicfDot11SecIEStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.2	HpnicfDot11SecIEStatusType	read-create	To enable the security Information element in the beacon and probe response frames sent by AP.
I32 hpnicfDot11SecurityCiphers	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.3	Integer32	read-create	The WLAN system support the following cipher type for data frame encryption. wep40(2) tkip(4) aesccmp(16) wep104(32) wpisms4(64) wep128(128) For each service policy, it could support multiple cipher types at the same time. So the value of object could combine multiple value of cipher type above. When the value of node equals to zero, it means no configuration or undo operation.
I32 hpnicfDot11CipherKeyIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.4	Integer32	read-create	Represents the key index of cipher key for packet. When hpnicfDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective.
OCT hpnicfDot11CipherKey	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.5	OCTET STRING	read-create	Represents the cipher key for packet. When hpnicfDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective.
ROW hpnicfDot11SrvPolicyExtRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.6	RowStatus	read-create	The status of this table entry.
INT hpnicfDot11CipherKeyType	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.7	INTEGER	read-create	Represents the cipher key type of hpnicfDot11CipherKey.
hpnicfDot11RadioPolicyExtTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4		not-accessible	The table defines the radio policy of each radio. It can't be modified if the radio policy is a default radio policy.
hpnicfDot11RadioPolicyExtEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1		not-accessible	Each entry contains information of each radio policy.
OCT hpnicfDot11RPAPSerialID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.1	OCTET STRING	not-accessible	This object represents the Serial ID of AP.
HPN hpnicfDot11RPRadioID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.2	HpnicfDot11RadioScopeType	not-accessible	This object represents each radio.
I32 hpnicfDot11RPBeaconInterval	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.3	Integer32	read-write	This object represents the interval for Beacon management frame.
I32 hpnicfDot11RPDtimInterval	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.4	Integer32	read-write	This object represents the number of beacon intervals that shall elapse between transmissions of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
I32 hpnicfDot11RPRtsThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.5	Integer32	read-write	This object represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
I32 hpnicfDot11RPFragThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.6	Integer32	read-write	This object represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
I32 hpnicfDot11RPShortRetryThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.7	Integer32	read-write	This object represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RTSThreshold, that shall be made before a failure condition is indicated.
I32 hpnicfDot11RPLongRetryThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.8	Integer32	read-write	This object represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RTSThreshold, and that shall be made before a failure condition is indicated.
I32 hpnicfDot11RPClientMaxCount	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.9	Integer32	read-write	This object represents the maximum number of stations supported by this radio policy.
I32 hpnicfDot11RPBeaconIntervalCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.10	Integer32	read-write	This object represents beacon interval.
hpnicfDot11SrvPortSecurityTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5		not-accessible	This table defines the WLAN security status for ESS, BSS and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, hpnicfPortSecurityTables should be used to configure port security.
hpnicfDot11SrvPortSecurityEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1		not-accessible	There is a row in this table for service policy.
HPN hpnicfDot11SecurityServicePolicyID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.1	HpnicfDot11ServicePolicyIDType	not-accessible	Represents the ID of each service policy.
INT hpnicfDot11SrvPortSecurityMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.2	INTEGER	read-write	Determines the security modes of the WLAN port. noRestrictions The default value, no any security mode is set. userLoginSecureExt Access to the port is denied until the port client is authorized (by 802.1X). psk Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext Access to the port is denied until the port client is authenticated (by ext).
INT hpnicfDot11SrvSecurityKeyType	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.3	INTEGER	read-write	This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone - This means the key type is not set yet. userLoginTxKeyTypeDot11Key - This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4 session encryption.
INT hpnicfDot11SrvSecurityPskKeyMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.4	INTEGER	read-write	This is the password input mode. When input as pskKeyModePassPhrase, hpnicfDot11SrvSecurityPskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, hpnicfDot11SrvSecurityPskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'.
STR hpnicfDot11SrvSecurityPskKeyString	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.5	DisplayString	read-write	This is the password string used for psk authentication.
INT hpnicfDot11SrvPortSecurityModeCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.6	INTEGER	read-write	Determines the security modes of the WLAN port. none - The default value, no any security mode is set. psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). radius - Access to the port is denied until the port client is authorized (by 802.1X). wlanex - Access to the port is denied until the port client is authenticated by wlan cert.
hpnicfDot11SrvPolicyExtendTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6		not-accessible	The table defines the parameters of each service policy.
hpnicfDot11SrvPolicyExtendEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6.1		not-accessible	Each entry contains information of each service policy.
INT hpnicfDot11SPEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6.1.1	INTEGER	read-write	Represents whether the service policy is enabled.
hpnicfDot11APConfigGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3
hpnicfDot11APTemplateTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1		not-accessible	By AP template CLI, administrator will configure the parameters of AP by convenience. Before AP boot up and connect to AC by CAPWAP tunnel, administrator will create AP template for each AP. When AP connect to AC, AC will assign configuration to AP by hpnicfDot11APSerialID information in AP template.
hpnicfDot11APTemplateEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1		not-accessible	Each entry contains configuration information for each AP.
OCT hpnicfDot11APTemplateName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.1	OCTET STRING	not-accessible	Represents the name of AP template.
OCT hpnicfDot11APSerialID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.2	OCTET STRING	read-create	Represents AP serial id.
OCT hpnicfDot11TemplateAPModelAlias	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.3	OCTET STRING	read-create	Represents the alias of AP model name.
OCT hpnicfDot11Description	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.4	OCTET STRING	read-create	This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed.
INT hpnicfDot11APWorkMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.5	INTEGER	read-create	Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
ROW hpnicfDot11APTemplateRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.6	RowStatus	read-create	The status of this table entry.
OCT hpnicfDot11APName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.7	OCTET STRING	read-create	Represents the AP name.
I32 hpnicfDot11StatisInterv	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.8	Integer32	read-create	Represents the interval of radio statistic.
T/F hpnicfDot11APBroadcastProbeReply	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.9	TruthValue	read-create	Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
I32 hpnicfDot11StaIdleTimerInterv	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.10	Integer32	read-create	Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
I32 hpnicfDot11StaKeepAliveTimerInterv	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.11	Integer32	read-create	Represents the interval of the keep alive requests sent between AP and STA.
I32 hpnicfDot11APCir	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.12	Integer32	read-create	Represents the committed information rate between AP and AC.
I32 hpnicfDot11APCbs	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.13	Integer32	read-create	Represents the committed burst size between AP and AC.
I32 hpnicfDot11APPriorityLevel	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.14	Integer32	read-create	This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP.
I32 hpnicfDot11APElementID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.15	Integer32	read-only	This object represents the AP element ID.
T/F hpnicfDot11APDevDetectEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.16	TruthValue	read-create	Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object hpnicfDot11APWorkMode is monitor, device detection can not be enabled with object hpnicfDot11APDevDetectEnable.
INT hpnicfDot11APGetIPMethod	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.17	INTEGER	read-create	This object represents the method how AP gets IP address.
INT hpnicfDot11StatisIntervMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.18	INTEGER	read-create	This object represents the mode of statics interval. normal - statics interval value between 10s to 120s realtime - statics interval value between 2s to 5s
T/F hpnicfDot11ApTrapEnabled	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.19	TruthValue	read-write	Represents whether the trap status is enabled or not. 'true' : Enable the trap status; 'false' : Disable the trap status.
INT hpnicfDot11ApFmwUpdState	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.20	INTEGER	read-create	Represents the status of version auto-update for an AP. The following values are supported: enable - AP version will be updated automatically. disable - AP version will not be updated automatically. inherit - The status will inherit value from apgroup-view or system-view.
INT hpnicfDot11StatisIntervModeCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.21	INTEGER	read-create	This object represents the mode of statistic interval. off - statistic interval value between 10s to 120s on - statistic interval value between 2s to 5s
OCT hpnicfDot11ApNasIDCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.22	OCTET STRING	read-create	Represents the NAS-ID of current service policy for each specific radio of AP.
hpnicfDot11RadioToConfigTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2		not-accessible	Before AP connects to AC, administrator will configure radio parameter to each radio.
hpnicfDot11RadioToConfigEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1		not-accessible	Each entry contains configuration information for each radio.
OCT hpnicfDot11APTemplateNameCfg	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.1	OCTET STRING	not-accessible	Represents the name of AP template.
HPN hpnicfDot11CfgRadioID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.2	HpnicfDot11RadioScopeType	not-accessible	Represents each radio.
OCT hpnicfDot11CfgRadioPolicyName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.3	OCTET STRING	read-write	Represents the name of radio policy.
HPN hpnicfDot11CfgRadioType	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.4	HpnicfDot11RadioType	read-write	Represents the radio will work with which 802.11 radio type.
HPN hpnicfDot11CfgChannel	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.5	HpnicfDot11ChannelScopeType	read-write	Represents the channel allocation of radio.
HPN hpnicfDot11CfgMaxTxPowerLevel	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.6	HpnicfDot11TxPwrLevelScopeType	read-write	Represents the maximal transmit power scope for AP.
HPN hpnicfDot11PreambleLen	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.7	HpnicfDot11PreambleType	read-write	Represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLen will be valid. Otherwise, the value for it will be invalid.
T/F hpnicfDot11CfgRadioStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.8	TruthValue	read-write	Represents the radio admin status whether is enabled or disabled.
U32 hpnicfDot11CfgRdElementID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.9	Unsigned32	read-only	Represents the element ID of this radio. It comprises two parts. The highest 24 bits are AP element ID and the lowest 8 bits are radio ID.
HPN hpnicfDot11CfgWorkMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.10	HpnicfDot11WorkMode	read-write	Represents work mode of the radio.
I32 hpnicfDot11CfgPwrAttValue	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.11	Integer32	read-write	Represents the value of power attenuation.
INT hpnicfDot11RadioTxArithmetic	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.12	INTEGER	read-write	Represents the transmission arithmetic of the radio. The following values are supported: quality - Consider the quality first during the transmission. bandwidth - Consider the bandwidth first during the transmission.
INT hpnicfDot11CfgChannelLockStat	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.13	INTEGER	read-write	Represents locked status of channel on the radio.
INT hpnicfDot11CfgPowerLockStat	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.14	INTEGER	read-write	Represents locked status of power on the radio.
U32 hpnicfDot11CfgLBRdGroupId	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.15	Unsigned32	read-write	Represents the load balance group ID allocated for the radio.
U32 hpnicfDot11CfgRRMSDRdGroupId	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.16	Unsigned32	read-write	Represents the RRM self-decisive group ID allocated for the radio.
HPN hpnicfDot11CfgRadioType2	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.17	HpnicfDot11RadioType2	read-write	Represents the radio will work with which 802.11 radio type.
T/F hpnicfDot11CfgIDSEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.18	TruthValue	read-write	Represents whether intrusion detection is enabled for this radio.
T/F hpnicfDot11CfgSaEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.19	TruthValue	read-write	Represents whether spectrum analysis is enabled.
T/F hpnicfDot11CfgSaCltRtFFTData	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.20	TruthValue	read-write	Represents whether to collect real-time FFT data for this radio.
INT hpnicfDot11CfgSaBand	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.21	INTEGER	read-write	Represents which band of channels will be monitored when collection real-time FFT data is enabled for this radio. Detection of interference devices and air quality will also be affected. Each band responds to the following channels. dot11g (Channels 1-14) dot11aLower (channels 36-64) dot11aMiddle (channels 100-140) dot11aUpper (channels 149-165).
hpnicfDot11APServiceSetTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3		not-accessible	For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies.
hpnicfDot11APServiceSetEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1		not-accessible	Each entry contains service policy information for each specific radio of AP.
HPN hpnicfDot11CfgServicePolicyID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.1	HpnicfDot11ServicePolicyIDType	not-accessible	Represents the ID of each service policy used by the AP.
ROW hpnicfDot11SrvSetRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.2	RowStatus	read-create	The status of this table entry.
I32 hpnicfDot11ServiceSetVlanId	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.3	Integer32	read-create	Represents the Vlan ID of BSS which is generated when service policy is binded with the Radio.
hpnicfDot11APSysInfoSetTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4		not-accessible	The table of the system information for each AP.
hpnicfDot11APSysInfoSetEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1		not-accessible	The system information configuration for each AP.
OCT hpnicfDot11APSysNetID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.1	OCTET STRING	read-write	Represents the system Net ID for AP.
I32 hpnicfDot11APCpuUsageThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.2	Integer32	read-write	The CPU usage threshold for AP.
I32 hpnicfDot11APMemUsageThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.3	Integer32	read-write	The memory usage threshold for AP.
hpnicfDot11APLimitTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5		not-accessible	For each connected APs, administrator could configure a series of limits. This table describes the limit information for AP(s).
hpnicfDot11APLimitEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1		not-accessible	Each entry contains the limit information for each AP.
I32 hpnicfDot11APSsidNumLimit	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.1	Integer32	read-write	Represents the upper limit of service template binded with this AP. All radios of AP share this limit. Default value 0 : There is no upper limit of service template binded with this AP.
I32 hpnicfDot11APUserCntLimit	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.2	Integer32	read-write	Represents the upper limit of user which has access to this AP. All BSSs binded with AP share this limit. Default value 0 : There is no upper limit of user which has access to this AP.
I32 hpnicfDot11APUserThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.3	Integer32	read-write	Represents the threshold of user which has access to this AP. All BSSs binded with AP share this limit. If the user counter is overflow, the trap will be sent. Default value 0 : There is no threshold of user which has access to this AP.
hpnicfDot11APIfSetTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6		not-accessible	The table of the interface information for each AP.
hpnicfDot11APIfSetEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1		not-accessible	The interface information configuration for each AP.
I32 hpnicfDot11APSetIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1.1	Integer32	not-accessible	Represents the index for a interface.
STR hpnicfDot11APIfAlias	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1.2	DisplayString	read-write	This object is an 'alias' name for the interface as specified by a network manager for AP.
hpnicfDot11APServiceVlanTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7		not-accessible	For all the radios on the AP, it could configure multiple service policies. The table describes the relationship between AP and service policies.
hpnicfDot11APServiceVlanEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1		not-accessible	Each entry contains service policy information for each AP.
OCT hpnicfDot11APServiceVlanSerialID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.1	OCTET STRING	not-accessible	This object represents AP serial id.
HPN hpnicfDot11APServiceVlanSPID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.2	HpnicfDot11ServicePolicyIDType	not-accessible	This object represents the ID of each service policy used by the AP.
I32 hpnicfDot11APServiceVlanId	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.3	Integer32	read-create	This object represents the VLAN ID of BSS which is generated when the service policy is bound to the radio.
ROW hpnicfDot11APServiceVlanRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.4	RowStatus	read-create	This object represents the status of this table entry.
hpnicfDot11RadioConfigTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8		not-accessible	Before AP connects to AC, administrator will configure radio parameter to each radio.
hpnicfDot11RadioConfigEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1		not-accessible	Each entry contains configuration information for each radio.
OCT hpnicfDot11RCAPSerialID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.1	OCTET STRING	not-accessible	This object represents the Serial ID of AP.
HPN hpnicfDot11RCRadioID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.2	HpnicfDot11RadioScopeType	not-accessible	This object represents each radio.
HPN hpnicfDot11RCRadioType	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.3	HpnicfDot11RadioType	read-write	This object represents the radio will work with which 802.11 radio type.
HPN hpnicfDot11RCChannel	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.4	HpnicfDot11ChannelScopeType	read-write	This object represents the channel allocation of radio.
HPN hpnicfDot11RCPreambleLen	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.5	HpnicfDot11PreambleType	read-write	This object represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLen will be valid. Otherwise, the value for it will be invalid.
I32 hpnicfDot11RCPwrAttValue	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.6	Integer32	read-write	This object represents the value of power attenuation.
HPN hpnicfDot11RCApPowerLevel	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.7	HpnicfDot11TxPwrLevelScopeType	read-write	Represents the maximal transmit power scope for AP.
T/F hpnicfDot11RCDynamicChlState	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.8	TruthValue	read-write	Enable/Disable dynamic channel selection.
T/F hpnicfDot11RCDynamicPowerState	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.9	TruthValue	read-write	Enable/Disable dynamic power selection for the band.
T/F hpnicfDot11RCRadioStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.10	TruthValue	read-write	Represents the radio admin status whether is enabled or disabled.
OCT hpnicfDot11RCRadioRate	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.11	OCTET STRING	read-write	Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format can be MCS X. The data transmit rates between AP and STA must fall into the configured rates. (Note: For 802.11n radios, the first value will be treated as a mandatory rate, and the second value will be treated as a supported rate. If you configure more than two rates, the configuration cannot take effect. If you configure only one rate, it is considered as the mandatory rate by default.)
I32 hpnicfDot11RCPwrAdjustStepLength	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.12	Integer32	read-only	Power adjustment step-length in dBm.
HPN hpnicfDot11RCRadioType2	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.13	HpnicfDot11RadioType2	read-write	This object represents the radio will work with which 802.11 radio type.
INT hpnicfDot11RCPreambleLenCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.14	INTEGER	read-write	This object represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLenCM will be valid. Otherwise, the value for it will be invalid.
INT hpnicfDot11RCDynamicChlStateCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.15	INTEGER	read-write	Enable/Disable dynamic channel selection.
INT hpnicfDot11RCRadioStatusCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.16	INTEGER	read-write	Represents the radio admin status whether is enabled or disabled.
OCT hpnicfDot11RCRadioRateCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.17	OCTET STRING	read-write	Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format of each value can be MCS X. The data transmit rates between AP and client should be one of the configured rates. (Note: For 802.11n radios, the first value is mandatory rate, and the second value is supported rate. If more than two rate values are configured, the configuration will not take effect. If only one rate value is configured, the mandatory rate will be set to the default value.)
HPN hpnicfDot11RCDynamicPowerStateCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.18	HpnicfDot11TruthValueCM	read-write	Enable/disable dynamic power selection for the band.
hpnicfDot11RadioSSIDCfgTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9		not-accessible	For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies.
hpnicfDot11RadioSSIDCfgEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1		not-accessible	Each entry contains SSID configuration information for each radio.
HPN hpnicfDot11RadioSSIDSerialID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.1	HpnicfDot11ObjectIDType	not-accessible	This object represents the serial ID of AP.
HPN hpnicfDot11RadioSSIDRadioID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.2	HpnicfDot11RadioScopeType	not-accessible	This object represents each radio.
I32 hpnicfDot11RadioSSIDWLANID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.3	Integer32	not-accessible	This object represents the WLAN ID of the BSSID.
HPN hpnicfDot11RadioSSIDIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.4	HpnicfDot11ServicePolicyIDType	read-create	This object represents the ID of each service policy used by the radio.
MAC hpnicfDot11RadioBSSID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.5	MacAddress	read-only	As MAC address format, it is used to identify BSS.
ROW hpnicfDot11RadioSSIDRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.6	RowStatus	read-create	RowStatus.
hpnicfDot11APSerialIDTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10		not-accessible	The table will provide the general information about APs.
hpnicfDot11APSerialIDEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1		not-accessible	Each entry contains the general information of an AP.
OCT hpnicfDot11SIDAPSerialID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.1	OCTET STRING	not-accessible	Represents AP serial id.
INT hpnicfDot11SIDAPWorkMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.2	INTEGER	read-create	Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
INT hpnicfDot11SIDAPGetIPMethod	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.3	INTEGER	read-create	This object represents the method how AP gets IP address.
OCT hpnicfDot11SIDAPTemplateName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.4	OCTET STRING	read-create	Represents the name of AP template.
OCT hpnicfDot11SIDModelAlias	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.5	OCTET STRING	read-create	Represents the alias of AP model name.
OCT hpnicfDot11SIDAPDescription	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.6	OCTET STRING	read-create	This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed.
ROW hpnicfDot11SIDRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.7	RowStatus	read-create	The status of this table entry.
OCT hpnicfDot11SIDAPName	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.8	OCTET STRING	read-create	Represents the AP name.
I32 hpnicfDot11SIDStatisInterv	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.9	Integer32	read-create	Represents the interval of radio statistic.
T/F hpnicfDot11SIDAPBroadcastProbeReply	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.10	TruthValue	read-create	Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
I32 hpnicfDot11SIDAPStaIdleTimerInterv	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.11	Integer32	read-create	Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
I32 hpnicfDot11SIDStaKeepAliveTimerInterv	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.12	Integer32	read-create	Represents the interval of the keep alive requests sent between AP and STA.
I32 hpnicfDot11SIDAPCir	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.13	Integer32	read-create	Represents the committed information rate between AP and AC.
I32 hpnicfDot11SIDAPCbs	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.14	Integer32	read-create	Represents the committed burst size between AP and AC.
I32 hpnicfDot11SIDAPPriorityLevel	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.15	Integer32	read-create	This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP.
I32 hpnicfDot11SIDAPElementID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.16	Integer32	read-only	This object represents the AP element ID.
T/F hpnicfDot11SIDAPDevDetectEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.17	TruthValue	read-create	Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object hpnicfDot11APWorkMode is monitor, device detection can not be enabled with object hpnicfDot11SIDAPDevDetectEnable.
INT hpnicfDot11SIDAPStatisIntervMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.18	INTEGER	read-create	This object represents the mode of statics interval. normal - statics interval value between 10s to 120s realtime - statics interval value between 2s to 5s
INT hpnicfDot11SIDAPWorkModeCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.19	INTEGER	read-create	Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. SemiMonitor - AP will supply WLAN service and Device detection is enabled.
hpnicfDot11APSTVlanTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11		not-accessible	For each service policy, it could be bind to several VLANs. The table describes the relationship between VLAN and service policies.
hpnicfDot11APSTVlanEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1		not-accessible	Each entry contains VLAN and service policy information for each specific radio of AP.
I32 hpnicfDot11CfgSTVLANID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.1	Integer32	read-create	Represents the VLAN that current Service Policy have bind to.
OCT hpnicfDot11CfgSTNASPortID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.2	OCTET STRING	read-only	Represents the NAS Port ID of current Service Policy for each specific radio of AP.
ROW hpnicfDot11CfgServiceSetRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.3	RowStatus	read-create	The status of this table entry.
OCT hpnicfDot11CfgSTNASID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.4	OCTET STRING	read-only	Represents the NAS ID of current Service Policy for each specific radio of AP.
hpnicfDot11RadioIntfConfigGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4
hpnicfDot11RadioIntfConfigTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1		not-accessible	The table defines the parameters for radio in AP, as per radio.
hpnicfDot11RadioIntfConfigEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1		not-accessible	Each entry contains information of each radio in AP.
I32 hpnicfDot11RadioIfIdx	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.1	Integer32	not-accessible	Represents the Radio IfIndex of radio in AP.
I32 hpnicfDot11RadioCfgBeaconIntvl	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.2	Integer32	read-write	Represents the interval for Beacon management frame.
I32 hpnicfDot11RadioCfgDtimIntvl	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.3	Integer32	read-write	Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
I32 hpnicfDot11RadioCfgRtsThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.4	Integer32	read-write	Represents the current minimum size,in octets,of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
I32 hpnicfDot11RadioCfgFragThreshold	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.5	Integer32	read-write	Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
I32 hpnicfDot11RadioCfgShtRetryThld	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.6	Integer32	read-write	Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RadioRTSThreshold, that shall be made before a failure condition is indicated.
I32 hpnicfDot11RadioCfglongRtrThld	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.7	Integer32	read-write	Represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RadioRTSThreshold, that shall be made before a failure condition is indicated.
U32 hpnicfDot11RadioCfgMaxRxLifetime	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.8	Unsigned32	read-write	Represents the elapsed time. After the time specified by hpnicfDot11RadioCfgMaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated.
HPN hpnicfDot11RadioCfgType	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.9	HpnicfDot11RadioType	read-write	Represents the radio will work with which 802.11 radio type.
HPN hpnicfDot11RadioCfgChannel	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.10	HpnicfDot11ChannelScopeType	read-write	Represents the channel allocation of radio.
HPN hpnicfDot11RadioCfgMaxTxPwrLvl	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.11	HpnicfDot11TxPwrLevelScopeType	read-write	Represents the maximal transmit power scope for AP.
HPN hpnicfDot11RadioCfgPreambleLen	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.12	HpnicfDot11PreambleType	read-write	Represents whether use long or short preamble for 802.11 MAC frame.
HPN hpnicfDot11RadioCfgWorkMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.13	HpnicfDot11WorkMode	read-write	Represents work mode of the radio.
T/F hpnicfDot11RadioCfgOnly11gEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.14	TruthValue	read-write	Represents whether enable only 802.11g radio mode or not. 'true' : Only 802.11g radio mode is enabled. 'false': Only 802.11g radio mode is disabled.
HPN hpnicfDot11RadioCfgType2	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.15	HpnicfDot11RadioType2	read-write	Represents the radio will work with which 802.11 radio type.
I32 hpnicfDot11RadioCfgRssithresholdCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.16	Integer32	read-write	Represents the minimum value of the RSSI. The clients with RSSI below this value will be refused to associate.
hpnicfDot11RadioIntfBindTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2		not-accessible	The table defines the binding information for each radio in AP.
hpnicfDot11RadioIntfBindEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1		not-accessible	Each entry contains the radio interface binding information in AP.
HPN hpnicfDot11RadioIntfBindSvcPlcyID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.1	HpnicfDot11ServicePolicyIDType	not-accessible	Represents the ID of each service policy.
U32 hpnicfDot11RadioIntfBindIfIdx	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.2	Unsigned32	read-create	Represents the Ifindex of interface which is binded to the radio.
ROW hpnicfDot11RadioIntfBindRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.3	RowStatus	read-create	The status of this table entry.
hpnicfDot11DataRateConfigGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.5
hpnicfDot11DataRateConfigTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1		not-accessible	Table will provide data rate configuration for a specific radio type.
hpnicfDot11DataRateConfigEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1		not-accessible	Each entry of the table will provide data rate configuration for a specific radio type.
HPN hpnicfDot11RadioTypeID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.1	HpnicfDot11RadioType	not-accessible	Represents the radio type.
OCT hpnicfDot11SupportedRateSet	1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.2	OCTET STRING	read-write	Represents the supported rate set of a particular radio type.
OCT hpnicfDot11MandatoryRateSet	1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.3	OCTET STRING	read-write	Represents the mandatory rate set of a particular radio type.
OCT hpnicfDot11DisabledRateSet	1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.4	OCTET STRING	read-write	Represents the disabled rate set of a particular radio type.
OCT hpnicfDot11SmartRateSet	1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.5	OCTET STRING	read-write	Represents the rate set of a particular radio type.
hpnicfDot11InterfaceConfigGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6
hpnicfDot11WlanEssIfTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1		not-accessible	This table is used to configure WLAN ESS interface.
hpnicfDot11WlanEssIfEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1		not-accessible	Each entry contains the WLAN ESS interface configuration.
I32 hpnicfDot11WlanEssIfNumber	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.1	Integer32	not-accessible	This node represents the WLAN ESS interface number.
I32 hpnicfDot11WlanEssIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.2	Integer32	read-only	This node represents the ifIndex of WLAN-ESS interface.
ROW hpnicfDot11WlanEssRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.3	RowStatus	read-create	This node represents the WLAN ESS interface row status.
hpnicfDot11WlanBssIfTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2		not-accessible	This table is used to configure WLAN BSS interface.
hpnicfDot11WlanBssIfEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1		not-accessible	Each entry contains the WLAN BSS interface configuration.
I32 hpnicfDot11WlanBssIfNumber	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.1	Integer32	not-accessible	This node represents the WLAN BSS interface number.
I32 hpnicfDot11WlanBssIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.2	Integer32	read-only	This node represents the ifIndex of WLAN-BSS interface.
ROW hpnicfDot11WlanBssRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.3	RowStatus	read-create	This node represents the WLAN BSS interface row status.
hpnicfDot11WLANEthernetIfTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3		not-accessible	This table is used to configure WLAN Ethernet interface.
hpnicfDot11WLANEthernetIfEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1		not-accessible	Each entry contains the WLAN Ethernet interface configuration.
I32 hpnicfDot11WlanEthernetIfNumber	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.1	Integer32	not-accessible	This node represents the WLAN Ethernet interface number.
I32 hpnicfDot11WLANEthernetIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.2	Integer32	read-only	This node represents the ifIndex of WLAN-Ethernet interface.
ROW hpnicfDot11WlanEthernetRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.3	RowStatus	read-create	This node represents the Wlan Ethernet interface row status.
hpnicfDot11PortSecurityTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4		not-accessible	This table defines the WLAN security status for ESS, BSS, mesh and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, hpnicfPortSecurityTables should be used to configure port security.
hpnicfDot11PortSecurityEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1		not-accessible	There is a row in this table for each ESS, BSS and WLAN-Ethernet interface.It is indexed using the object ifIndex in RFC1213-MIB.
INT hpnicfDot11PortSecurityMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.1	INTEGER	read-write	Determines the security modes of the WLAN port. noRestrictions - The default value,no any security mode is set. userLoginSecureExt - Access to the port is denied until the port client is authorized (by 802.1X). psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk - The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk - This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext - Access to the port is denied until the port client is authenticated (by ext).
INT hpnicfDot11SecurityUserLoginTxKeyType	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.2	INTEGER	read-write	This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone - This means the key type is not set yet. userLoginTxKeyTypeDot11Key - This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4 session encryption.
INT hpnicfDot11SecurityPskKeyMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.3	INTEGER	read-write	This is the password input mode. When input as pskKeyModePassPhrase, hpnicfDot11SecurePskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, hpnicfDot11SecurePskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'.
STR hpnicfDot11SecurityPskKeyString	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.4	DisplayString	read-write	This is the password string used for psk authentication.
hpnicfDot11WlanMeshIfTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5		not-accessible	This table is used to configure WLAN mesh interface.
hpnicfDot11WlanMeshIfEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1		not-accessible	Each entry contains the WLAN mesh interface configuration.
I32 hpnicfDot11WlanMeshIfNumber	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.1	Integer32	not-accessible	This node represents the WLAN mesh interface number.
I32 hpnicfDot11WlanMeshIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.2	Integer32	read-only	This node represents the index of WLAN mesh interface.
ROW hpnicfDot11WlanMeshRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.3	RowStatus	read-create	This node represents the WLAN mesh interface row status.
hpnicfDot11ACBackupGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.7
IP hpnicfDot11BackupACAdrssIP	1.3.6.1.4.1.11.2.14.11.15.2.75.4.7.1	InetAddress	read-write	This object represents the backup AC IP address. If the backup AC IP address is not configured, the object value is 0.0.0.0.
IP hpnicfDot11BackupACAdrssIPv6	1.3.6.1.4.1.11.2.14.11.15.2.75.4.7.2	InetAddress	read-write	This object represents the backup AC IPv6 address. If the backup AC IPv6 address is not configured, the object value is 0::0.
hpnicfDot11RadioElementConfigGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8
hpnicfDot11nRadioCfgTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1		not-accessible	This table is used to configure dot11n on the radio.
hpnicfDot11nRadioCfgEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1		not-accessible	This entry contains the dot11n configuration on the radio.
HPN hpnicfDot11nRadioCfgIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.1	HpnicfDot11RadioElementIndex	not-accessible	Represents index of the radio.
T/F hpnicfDot11nAMpduEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.2	TruthValue	read-write	Enable the function of A-MPDU.
T/F hpnicfDot11nAMsduEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.3	TruthValue	read-write	Enable the function of A-MSDU.
T/F hpnicfDot11nClientDot11nOnly	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.4	TruthValue	read-write	If radio type is 802.11an or 802.11gn, only permit clients of 11n mode. If radio type is 802.11ac, permit clients of 11n and 11ac mode.
INT hpnicfDot11nChanelBand	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.5	INTEGER	read-write	Specify the bandwidth mode.
T/F hpnicfDot11nShortGiEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.6	TruthValue	read-write	The function of Short GI.
T/F hpnicfDot11nClientDot11acOnly	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.7	TruthValue	read-write	Only permit clients of 11ac mode.
hpnicfDot11RadioWDSTable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2		not-accessible	This table is used to configure WDS on the radio.
hpnicfDot11RadioWDSEntry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1		not-accessible	Each entry contains the WDS configuration on the radio.
HPN hpnicfDot11RadioWDSIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.1	HpnicfDot11RadioElementIndex	not-accessible	Represents the element index of radio.
INT hpnicfDot11RadioWDSMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.2	INTEGER	read-write	Represents enable the WDS mode or not. nowds: The WDS mode is disabled. wds : The WDS mode is enabled
OCT hpnicfDot11RadioWDSNetWorkID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.3	OCTET STRING	read-write	Represents the mesh ID of WDS.
INT hpnicfDot11WDSSecPskKeyMode	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.4	INTEGER	read-write	Represents the PSK mode of WDS.
STR hpnicfDot11WDSSecPskKeyString	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.5	DisplayString	read-write	Represents the PSK value of WDS.
hpnicfDot11nRadioCfg2Table	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3		not-accessible	This table is used to configure dot11n on the radio.
hpnicfDot11nRadioCfg2Entry	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1		not-accessible	This entry contains the dot11n configuration on the radio.
HPN hpnicfDot11nRadioCfg2APIDIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.1	HpnicfDot11ObjectIDType	not-accessible	Represents index of the AP.
HPN hpnicfDot11nRadioCfg2RadioIDIndex	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.2	HpnicfDot11RadioScopeType	not-accessible	Represents index of the radio.
T/F hpnicfDot11nRadioCfg2AMpduEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.3	TruthValue	read-write	Enable the function of A-MPDU.
T/F hpnicfDot11nRadioCfg2AMsduEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.4	TruthValue	read-write	Enable the function of A-MSDU.
T/F hpnicfDot11nRadioCfg2ClientDot11nOnly	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.5	TruthValue	read-write	If radio type is 802.11an or 802.11gn, only permit clients of 11n mode. If radio type is 802.11ac, permit clients of 11n and 11ac mode.
INT hpnicfDot11nRadioCfg2ChannelBand	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.6	INTEGER	read-write	Specify the bandwidth mode.
T/F hpnicfDot11nRadioCfg2ShortGiEnable	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.7	TruthValue	read-write	Enable the function of Short GI.
INT hpnicfDot11nRadioCfg2AMpduEnableCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.8	INTEGER	read-write	Enable the function of A-MPDU.
INT hpnicfDot11nRadioCfg2ChannelBandCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.9	INTEGER	read-write	Specify the bandwidth mode.
INT hpnicfDot11nRadioCfg2ShortGiEnableCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.10	INTEGER	read-write	Enable the function of Short GI.
T/F hpnicfDot11nRadioCfg2ClientDot11acOnly	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.11	TruthValue	read-write	Only permit clients of 11ac mode.
HPN hpnicfDot11nRadioCfg2ClientDot11nOnlyCM	1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.12	HpnicfDot11TruthValueCM	read-write	If radio type is 802.11an or 802.11gn, permit only clients of 11n mode. If radio type is 802.11ac, permit clients of both 11n and 11ac mode.
hpnicfDot11CfgNotifyGroup	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9
hpnicfDot11CfgNotifications	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0
NTF hpnicfDot11CfgCipherChange	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.1			This notification is sent when cipher type of corresponding service template is changed.
NTF hpnicfDot11CfgPSKChange	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.2			This notification is sent when pre-shared key of corresponding service template is changed.
NTF hpnicfDot11SSIDWepIDConflictTrap	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.3			This notification will be sent when the same wep ID is configured on two service policies.
hpnicfDot11CfgTrapVarObjects	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1
I32 hpnicfDot11PreConflictTemplateNum	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.1	Integer32	accessible-for-notify	Represents previous service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration.
I32 hpnicfDot11CurrConflictTemplateNum	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.2	Integer32	accessible-for-notify	Represents current service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration.
I32 hpnicfDot11ConflictCipherIdx	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.3	Integer32	accessible-for-notify	Represents wep ID that conflicted with.
HPN hpnicfDot11ConfigureAPID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.4	HpnicfDot11ObjectIDType	accessible-for-notify	Represents which AP is configured.
HPN hpnicfDot11ConfigureRadioID	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.5	HpnicfDot11RadioScopeType	accessible-for-notify	Represents which radio in AP is configured.
MAC hpnicfDot11ConfigureAPMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.6	MacAddress	accessible-for-notify	Represents MAC Address of AP.

RFC description

WLAN configuration MIB providing 802.11 wireless settings, AP templates, and security policies.

Start monitoring H3C/HPE Networking (ICF-based) wireless controller (WLAN config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-DOT11-CFG-MIB

What Is HPN-ICF-DOT11-CFG-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description