A3COM-HUAWEI-LswINF-MIB

All MIBs › A3COM-HUAWEI-LswINF-MIB

Last Updated: 2001-06-29

Category: Network Interfaces, Vendor: H3C/HH3C

Description: Monitors physical and logical interface status, speed, and error counters on H3C LAN switch platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is A3COM-HUAWEI-LswINF-MIB?

A3COM-HUAWEI-LswINF-MIB (module hwLswL2InfMib) is a Huawei/H3C joint-venture enterprise MIB (lswCommon 5, from A3COM-HUAWEI-OID-MIB) that extends the standard IF-MIB ifTable with LAN-switch-specific per-interface objects via the hwifXXTable, which AUGMENTS ifEntry. Its HwIfXXEntry sequence covers physical/aggregation/mirror-port flags (hwifUnBoundPort, hwifISPhyPort, hwifAggregatePort, hwifMirrorPort), VLAN type and multicast/broadcast suppression controls (hwifVLANType, hwifMcastControl, hwifPpsMcastControl, the various hwifUniSuppression/hwifMulSuppression rate-limiting objects), flow control and MAC learning controls, and interface-level payload/error counters (hwifOutPayloadOctets, hwifInPayloadOctets, hwifInErrorPktsRate, hwifInPkts, hwifInNormalPkts, hwifOutPkts). Because it augments ifEntry, every object is indexed by the same ifIndex as the standard IF-MIB, so this MIB is best understood as a Huawei-specific supplement layered directly on top of standard interface monitoring rather than a standalone table. It has been revised extensively since 2001 (through V3.3 in 2011) as H3C/Huawei LAN switch platforms added features like port isolation groups and combo-port support, and it is deployed on H3C/Huawei LAN switch platforms, for which the A3COM-HUAWEI-LswINF-MIB download supplies the object definitions.

IPNetwork Monitor allows you to monitor SNMP objects defined in A3COM-HUAWEI-LswINF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C/Huawei LAN switch platforms (A3Com-Huawei joint venture product line)

Monitoring Examples

An operator polls hwifInErrorPktsRate and hwifAggregatePort for a given ifIndex to check whether a port that is supposed to be part of a link aggregation group is seeing an abnormal error rate; a rising hwifInErrorPktsRate on an hwifAggregatePort-true interface would point to a bad cable or transceiver degrading one member of the aggregate.

What Can Be Monitored

physical/aggregation/mirror port flags
VLAN type and multicast/broadcast suppression settings
flow control and MAC-learning controls
interface payload octet counters
interface error packet rate
in/out packet counters

Imported Objects

From A3COM-HUAWEI-OID-MIB

lswCommon

OBJECT-IDENTITY

From RFC1213-MIB

ifEntry
ifIndex

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using hwifOutPayloadOctets OID:

Select an H3C/Huawei LAN switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hwifOutPayloadOctets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The actual output octets of the interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT hwBpduTunnelStatus	1.3.6.1.4.1.43.45.1.2.23.1.5.1.8	INTEGER	read-write	Bpdu tunnel enable status.
hwethernetEntry	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1		not-accessible	Entries of Ethernet port attribute table
hwethernetTable	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4		not-accessible	Ethernet port attribute table.
INT hwGlobalBroadcastMaxPps	1.3.6.1.4.1.43.45.1.2.23.1.5.1.6	INTEGER	read-write	The global max packets per second. When it is set, the value of BroadcastMaxPps in all ports will be changed to that setting.
INT hwGlobalBroadcastMaxRatio	1.3.6.1.4.1.43.45.1.2.23.1.5.1.7	INTEGER	read-write	The global max-ratio of broadcast from 0 to 100 percent. When it is set, the value of BroadcastMaxRatio in all ports will be changed to that setting.
hwifAggregateEntry	1.3.6.1.4.1.43.45.1.2.23.1.1.2.1		not-accessible	Port aggregation information table.
INT hwifAggregateModel	1.3.6.1.4.1.43.45.1.2.23.1.1.2.1.4	INTEGER	read-write	Load sharing mode for the port aggregation.
ROW hwifAggregateOperStatus	1.3.6.1.4.1.43.45.1.2.23.1.1.2.1.5	RowStatus	read-create	Current operation status of the row.
T/F hwifAggregatePort	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.3	TruthValue	read-only	Whether it is the aggregated port. (if the port participates in the aggregation, this value is true.)
NUM hwifAggregatePortIndex	1.3.6.1.4.1.43.45.1.2.23.1.1.2.1.1	InterfaceIndex	read-only	Index number of the main aggregated port.
POR hwifAggregatePortListPorts	1.3.6.1.4.1.43.45.1.2.23.1.1.2.1.3	PortList	read-write	Portlist of a aggregating.
OCT hwifAggregatePortName	1.3.6.1.4.1.43.45.1.2.23.1.1.2.1.2	OCTET STRING	read-write	Aggregation group name.
hwifAggregateTable	1.3.6.1.4.1.43.45.1.2.23.1.1.2		not-accessible	Port aggregation information table.
I32 hwifBKbpsMulSuppression	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.27	Integer32	read-write	With bandwidth-based multicast suppression, the bandwidth is measured in Kbps. The upper limit of the multicast suppession with bandwidth-based(Kbps) is the value of hwifBKbpsMulSuppressionMax in the entry. The value of hwifBKbpsMulSuppression must be multiple of the value of hwifBKbpsMulSuppressionStep. The default value of hwifBKbpsMulSuppression is the value of hwifBKbpsMulSuppressionMax.
I32 hwifBKbpsMulSuppressionMax	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.25	Integer32	read-only	The maximum value of the multicast suppression with bandwidth-based(Kbps) that a port can be configured.
I32 hwifBKbpsMulSuppressionStep	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.26	Integer32	read-only	The step of multicast suppression with bandwidth-based(Kbps).
I32 hwifBKbpsUniSuppression	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.34	Integer32	read-write	With bandwidth-based unicast suppression, the bandwidth is measured in Kbps. The upper limit of the unicast suppession with bandwidth-based(Kbps) is the value of hwifBKbpsUniSuppressionMax in the entry. The value of hwifBKbpsUniSuppression must be multiple of the value of hwifBKbpsUniSuppressionStep. The default value of hwifBKbpsUniSuppression is the value of hwifBKbpsUniSuppressionMax.
I32 hwifBKbpsUniSuppressionMax	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.32	Integer32	read-only	The maximum value of the unicast suppression with bandwidth-based (Kbps) that a port can be configured.
I32 hwifBKbpsUniSuppressionStep	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.33	Integer32	read-only	The step of unicast suppression with bandwidth-based(Kbps).
I32 hwifBMbpsMulSuppression	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.24	Integer32	read-write	With bandwidth-based multicast suppression, the bandwidth is measured in Mbps. The upper limit of the multicast suppession with bandwidth-based(Mbps) is the value of hwifBMbpsMulSuppressionMax in the entry. The default value of hwifBMbpsMulSuppression is the value of hwifBMbpsMulSuppressionMax.
I32 hwifBMbpsMulSuppressionMax	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.23	Integer32	read-only	The maximum value of the multicast suppression with bandwidth-based(Mbps) that a port can be configured.
I32 hwifBMbpsUniSuppression	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.31	Integer32	read-write	With bandwidth-based Unicast suppression, the bandwidth is measured in Mbps. The upper limit of the unicast suppession with bandwidth-based(Mbps) is the value of hwifBMbpsUniSuppressionMax in the entry. The default value of hwifBMbpsUniSuppression is the value of hwifBMbpsUniSuppressionMax.
I32 hwifBMbpsUniSuppressionMax	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.30	Integer32	read-only	The maximum value of the unicast suppression with bandwidth-based (Mbps) that a port can be configured.
INT hwifClearStat	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.9	INTEGER	read-write	Clear all port statistics. Read operation not supported.
INT hwifComboActivePort	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.22	INTEGER	read-write	Active port on combo interface.
INT hwifComboPortCurActive	1.3.6.1.4.1.43.45.1.2.23.1.1.4.1.2	INTEGER	read-write	Current active interface of combo interfaces. The value 'fiber' means the interface with fiber connector of the pair of combo-port interfaces is active. The value 'copper' means the interface with copper connector of the pair is active. The value 'na' means not supported.
hwifComboPortEntry	1.3.6.1.4.1.43.45.1.2.23.1.1.4.1		not-accessible	The entry of hwifComboPortTable.
NUM hwifComboPortIndex	1.3.6.1.4.1.43.45.1.2.23.1.1.4.1.1	InterfaceIndex	read-only	The combo-port interface index. Its value is the same as the value of ifIndex in ifTable, but only includes indexes of the combo-port interfaces.
hwifComboPortTable	1.3.6.1.4.1.43.45.1.2.23.1.1.4		not-accessible	Combo-port table.
SPE hwifEthernetAutoSpeed	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.20	SpeedModeFlag	read-write	This object indicates which kinds of speed mode are negotiable on this port. Only when a bit of hwifEthernetAutoSpeedMask is '1', the corresponding bit of this object can be set to '1', indicating the corresponding speed mode is negotiable. For example, if the value of hwifEthernetAutoSpeedMask is 0xA0, which indicates speed mode 's10M' and 's1000M' are negotiable, the possible value of this object should be one of the four values (0x00, 0x20, 0x80 and 0xA0). If the value of hwifEthernetSpeed is not 'auto', the value of this object is insignificant and should be ignored. The value length of this object should be as long as that of hwifEthernetAutoSpeedMask.
SPE hwifEthernetAutoSpeedMask	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.19	SpeedModeFlag	read-only	This object specifies which kinds of speed mode can be negotiated. Each bit corresponds to a kind of speed mode. If the value of a bit is '1', it means the corresponding speed mode is negotiable on the port. Otherwise the negotiation for that kind of speed mode is not supported on this port. If there are several negotiable speed modes, all bits for them are '1'. For example, if the speed mode 's10M' and 's1000M' can be negotiable, the value of this object is 0xA0.
INT hwifEthernetDuplex	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.3	INTEGER	read-write	Ethernet interface mode.
INT hwifEthernetFlowInterval	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.12	INTEGER	read-write	Set flow interval of the ethernet. The NMS should set value to integer which is a multiple of 5.
OCT hwifEthernetIsolate	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.13	OCTET STRING	read-write	Isolate group means that all ports in the same isolate group can not send and receive packets each other. Each octet within this value specifies a set of eight isolate groups, with the first octet specifying isolate groups 1 through 8, the second octet specifying isolate groups 9 through 16, etc. Within each octet, the leftmost bit is the first bit. the first bit represents the lowest numbered isolate group, and the last bit represents the highest numbered isolate group. one port can belong to more than one isolate group. Thus, each isolate group is represented by a single bit within the value of this object. If that bit has a value of '1', then that isolate group includes this port; the port is not included if its bit has a value of '0'. for example, the first octet is '10000100' means that the port is included in the isolate group 1 and isolate group 6.
INT hwifEthernetMdi	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.7	INTEGER	read-write	Type of the line connected to the port. MDI-II (straight-through cable): 1 MDI-X (crossover cable): 2 MDI-AUTO (auto-sensing): 3
INT hwifEthernetMTU	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.4	INTEGER	read-write	MTU on the Ethernet interface.
INT hwifEthernetSpeed	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.5	INTEGER	read-write	Ethernet interface speed.
INT hwifEthernetTest	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.10	INTEGER	read-write	Test this interface. The actual testing will be different according to products. Read operation not supported.
T/F hwifFlowControl	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.7	TruthValue	read-write	Flow control status.
hwifHybridPortEntry	1.3.6.1.4.1.43.45.1.2.23.1.1.3.1		not-accessible	Hybrid-port configuration table.
INT hwifHybridPortIndex	1.3.6.1.4.1.43.45.1.2.23.1.1.3.1.1	INTEGER	read-only	Index number of Hybrid-port.
hwifHybridPortTable	1.3.6.1.4.1.43.45.1.2.23.1.1.3		not-accessible	Hybrid-port configuration table.
OCT hwifHybridTaggedVlanListHigh	1.3.6.1.4.1.43.45.1.2.23.1.1.3.1.3	OCTET STRING	read-write	Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each tagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is tagged in the set of VLANs; the VLAN is not tagged if its bit has a value of '0'.
OCT hwifHybridTaggedVlanListLow	1.3.6.1.4.1.43.45.1.2.23.1.1.3.1.2	OCTET STRING	read-write	Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each tagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is tagged in the set of VLANs; the VLAN is not tagged if its bit has a value of '0'.
OCT hwifHybridUnTaggedVlanListHigh	1.3.6.1.4.1.43.45.1.2.23.1.1.3.1.5	OCTET STRING	read-write	Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'.
OCT hwifHybridUnTaggedVlanListLow	1.3.6.1.4.1.43.45.1.2.23.1.1.3.1.4	OCTET STRING	read-write	Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'.
I32 hwifInErrorPktsRate	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.37	Integer32	read-only	The rate of inbound error packets on the interface.
C64 hwifInNormalPkts	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.39	Counter64	read-only	The number of normal packets received on the interface.
C64 hwifInPayloadOctets	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.36	Counter64	read-only	The actual input octets of the interface.
C64 hwifInPkts	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.38	Counter64	read-only	The number of packets received on the interface.
I32 hwifIsolateGroupID	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.17	Integer32	read-write	Isolate group identifier. Value zero means this interface does not belong to any isolate group.
T/F hwifISPhyPort	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.2	TruthValue	read-only	Whether it is a physical interface.
INT hwifisUplinkPort	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.18	INTEGER	read-only	Ethernet uplink status, default value is 2.
INT hwifMacAddressLearn	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.9	INTEGER	read-only	This object indicates if the interface is allowed to learn mac address. eanbled(1) means the interface can learn mac address, otherwise disabled(2) can be set.
INT hwifMacAddrLearnMode	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.11	INTEGER	read-only	Status indicates mac address learn mode of the interface. IVL(1) means independent VLAN learning. SVL means shared VLAN learning.
INT hwifMcastControl	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.6	INTEGER	read-write	Broadcast storm suppression with the step length of 1, ranging from 1 to 100 percent. In some products the step is 5, ranging from 5 to 100.
T/F hwifMirrorPort	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.4	TruthValue	read-write	Whether it is a mirror port.
I32 hwifMulSuppression	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.20	Integer32	read-write	The multicast suppression with ranging from 1 to 100 percent in ratio mode. The step is determined by hwifMulSuppressionStep.
I32 hwifMulSuppressionStep	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.16	Integer32	read-only	The step of multicast suppression in ratio mode.
C64 hwifOutPayloadOctetsEx	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.35	Counter64	read-only	The actual output octets of the interface.
C64 hwifOutPkts	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.40	Counter64	read-only	The number of packets sent on the interface.
INT hwifPpsBcastDisValControl	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.13	INTEGER	read-write	Control the port's pps(packet per second) broadcast suppression. When the port is enabled, its pps broadcast suppression value is the global disperse value, and when disabled, it doesn't suppress broadcast.
I32 hwifPpsMcastControl	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.12	Integer32	read-write	The broadcast suppression with pps(packet per second) type. The max value is determined by the port type and product.
I32 hwifPpsMulSuppression	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.21	Integer32	read-write	The multicast suppression in pps(packet per second) mode. The max pps value is determined by hwifPpsMulSuppressionMax.
I32 hwifPpsMulSuppressionMax	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.17	Integer32	read-only	The max pps(packet per second) value of multicast suppression in pps mode.
I32 hwifPpsUniSuppression	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.19	Integer32	read-write	The unicast suppression in pps(packet per second) mode. The max value is determined by hwifPpsUniSuppressionMax.
I32 hwifPpsUniSuppressionMax	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.15	Integer32	read-only	The max pps(packet per second) value of unicast suppression in pps mode.
T/F hwifSrcMacControl	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.8	TruthValue	read-only	Whether to filter by source MAC address.
T/F hwifUnBoundPort	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.1	TruthValue	read-only	Whether it is the unbound port. (true indicates that the port is the main port of the aggregation or the port does not participate in the aggregation.)
I32 hwifUniSuppression	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.18	Integer32	read-write	The unicast suppression with the ranging from 1 to 100 percent in ratio mode. The step is determined by hwifUniSuppressionStep.
I32 hwifUniSuppressionStep	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.14	Integer32	read-only	The step of unicast suppression in ratio mode.
DRO hwifUnknownPacketDropMul	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.28	DropDirection	read-write	Control the port's unknown-multicast packets drop. When inbound direction is enabled on this port, the port will drop unknown-multicast packets in inbound direction. When outbound direction is enabled on this port, the port will drop unknown-multicast packets in outbound direction. When both directions are enabled on this port, the port will drop unknown-multicast packets in both inbound and outbound directions.
DRO hwifUnknownPacketDropUni	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.29	DropDirection	read-write	Control the port's unknown-unicast packets drop. When inbound direction is enabled on this port, the port will drop unknown-unicast packets in inbound direction. When outbound direction is enabled on this port, the port will drop unknown-unicast packets in outbound direction. When both directions are enabled on this port, the port will drop unknown-unicast packets in both inbound and outbound directions.
OCT hwifVLANTrunkAllowListHigh	1.3.6.1.4.1.43.45.1.2.23.1.5.1.3.1.7	OCTET STRING	read-write	Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is allowed in the set of VLANs; the VLAN is not allowed if its bit has a value of '0'.
OCT hwifVLANTrunkAllowListLow	1.3.6.1.4.1.43.45.1.2.23.1.5.1.3.1.6	OCTET STRING	read-write	Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is allowed in the set of VLANs; the VLAN is not allowed if its bit has a value of '0'.
INT hwifVLANTrunkGvrpRegistration	1.3.6.1.4.1.43.45.1.2.23.1.5.1.3.1.2	INTEGER	read-write	GVRP registration information normal: This is the default configuration. Allow create, register and unregister vlans dynamiclly at this port. fixed: Aallow create and register vlan manually at this port. Prevent from unregistering vlans or registering known vlans of this port at another trunk port. forbidden: Unregister all vlans but vlan 1, forbid to create or register any other vlans at this port.
NUM hwifVLANTrunkIndex	1.3.6.1.4.1.43.45.1.2.23.1.5.1.3.1.1	InterfaceIndex	read-only	Index number of the VLANTrunk interface.
OCT hwifVLANTrunkPassListHigh	1.3.6.1.4.1.43.45.1.2.23.1.5.1.3.1.5	OCTET STRING	read-only	Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each actually passed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is actually passed in the set of VLANs; the VLAN is not actually passed if its bit has a value of '0'.
OCT hwifVLANTrunkPassListLow	1.3.6.1.4.1.43.45.1.2.23.1.5.1.3.1.4	OCTET STRING	read-only	Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each actually passed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is actually passed in the set of VLANs; the VLAN is not actually passed if its bit has a value of '0'.
hwifVLANTrunkStatusEntry	1.3.6.1.4.1.43.45.1.2.23.1.5.1.3.1		not-accessible	Gvrp attributes on the VlanTrunk port.
hwifVLANTrunkStatusTable	1.3.6.1.4.1.43.45.1.2.23.1.5.1.3		not-accessible	Gvrp attributes on the VlanTrunk port.
INT hwifVLANType	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.5	INTEGER	read-write	port vlan types. hybrid (3) port can carry multiple VLANs. If fabric function is supported, fabric(4) means the port is a fabric port.
INT hwifVlanVPNStatus	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.14	INTEGER	read-write	Vlan VPN enable status.
I32 hwifVlanVPNTPID	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.16	Integer32	read-write	Port based Vlan VPN TPID(Tag Protocol Indentifier), default value is 0x8100. Please refer to hwVlanVPNTPIDMode to get more information.
INT hwifVlanVPNUplinkStatus	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.15	INTEGER	read-write	Vlan VPN uplink status.
INT hwifXXBasePortIndex	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.10	INTEGER	read-only	Index number of the port and the first port index of the device is 1.
INT hwifXXDevPortIndex	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1.11	INTEGER	read-only	Device index of the port.
hwifXXEntry	1.3.6.1.4.1.43.45.1.2.23.1.1.1.1		not-accessible	Entries of extended Huawei private interface information table.
hwifXXTable	1.3.6.1.4.1.43.45.1.2.23.1.1.1		not-accessible	Extended Huawei private interface information table.
I32 hwIsolateGroupMax	1.3.6.1.4.1.43.45.1.2.23.1.5.1.5	Integer32	read-only	Max isolate group that this device support, the value is zero means that the device does not support isolate group.
hwLswExtInterface	1.3.6.1.4.1.43.45.1.2.23.1.1
hwLswL2InfMib	1.3.6.1.4.1.43.45.1.2.23.1.5
hwLswL2InfMibObject	1.3.6.1.4.1.43.45.1.2.23.1.5.1
INT hwMaxMacLearn	1.3.6.1.4.1.43.45.1.2.23.1.5.1.4.1.8	INTEGER	read-write	The maximum number of MAC addresses that the port can learn. The value -1 means that the number of Mac addresses that the port can learn is unlimited.
I32 hwMaxMacLearnRange	1.3.6.1.4.1.43.45.1.2.23.1.5.1.12	Integer32	read-only	The maximum number of MAC address that the port supports.
STR hwPortIsolateGroupDescription	1.3.6.1.4.1.43.45.1.2.23.1.5.1.11.1.4	DisplayString	read-create	Port isolate group description, default value is zero-length string.
hwPortIsolateGroupEntry	1.3.6.1.4.1.43.45.1.2.23.1.5.1.11.1		not-accessible	The entry of hwPortIsolateGroupTable.
I32 hwPortIsolateGroupIndex	1.3.6.1.4.1.43.45.1.2.23.1.5.1.11.1.1	Integer32	not-accessible	Port isolate group identifier. The index of the hwPortIsolateGroupTable. The value ranges from 1 to the limit of isolate group quantity.
ROW hwPortIsolateGroupRowStatus	1.3.6.1.4.1.43.45.1.2.23.1.5.1.11.1.3	RowStatus	read-create	Current operation status of the row.
hwPortIsolateGroupTable	1.3.6.1.4.1.43.45.1.2.23.1.5.1.11		not-accessible	Isolate Group attribute table.
NUM hwPortIsolateUplinkIfIndex	1.3.6.1.4.1.43.45.1.2.23.1.5.1.11.1.2	InterfaceIndex	read-create	Index number of the uplink interface.
INT hwSlotPortMax	1.3.6.1.4.1.43.45.1.2.23.1.5.1.1	INTEGER	read-only	Max ports of the slots.
INT hwSwitchPortMax	1.3.6.1.4.1.43.45.1.2.23.1.5.1.2	INTEGER	read-only	Max ports that this switch includes.
I32 hwVlanVPNTPID	1.3.6.1.4.1.43.45.1.2.23.1.5.1.10	Integer32	read-write	Global Vlan VPN TPID(Tag Protocol Indentifier), default value is 0x8100.
INT hwVlanVPNTPIDMode	1.3.6.1.4.1.43.45.1.2.23.1.5.1.9	INTEGER	read-only	Vlan VPN TPID mode. The value 'port-based' means VLAN VPN TPID value would be set based on port via hwifVlanVPNTPID. In this situation, hwVlanVPNTPID is meaningless and always return 0x8100. The value 'global' means VLAN VPN TPID value should be set globally via hwVlanVPNTPID. In this situation, hwifVlanVPNTPID in hwethernetTable has the same value with hwVlanVPNTPID.

RFC description

Manages Huawei LAN switch interface configuration including VLANs and broadcast suppression.

Start monitoring H3C/Huawei LAN switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download A3COM-HUAWEI-LswINF-MIB