All MIBs › HH3C-TUNNEL-MIB
Organization: Hangzhou H3C Tech. Co., Ltd.
Last Updated: 2013-02-28
Category: Network Interfaces, Technology: VPN, VPN and Security, Vendor: H3C/HH3C
Description: HH3C MIB for tunnel interface management supporting GRE, IPsec, and other tunnel types on H3C devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HH3C-TUNNEL-MIB?
HH3C-TUNNEL-MIB is an H3C enterprise MIB for managing tunnel interfaces such as GRE, IPsec, and VXLAN tunnels on H3C/Comware devices. It exposes tunnel interface configuration data, including encapsulation method, hop limit, security mode, ToS/flow-label handling, and local/remote tunnel endpoint addresses. Its monitoring focus is on the software/protocol configuration and status of tunnel interfaces rather than physical hardware -- an operator can confirm a tunnel's encapsulation type, endpoint addresses, and security settings to verify it is correctly established. It builds on standard interface and address-type conventions (InetAddressType/InetAddress) common to IETF tunnel MIBs, though it is itself an H3C-proprietary module. It is typically deployed on H3C/Comware routers and switches providing GRE, IPsec, or VXLAN tunnel connectivity between sites or data centers, where HH3C-TUNNEL-MIB SNMP monitoring confirms each tunnel remains correctly established.
IPNetwork Monitor allows you to monitor SNMP objects defined in HH3C-TUNNEL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- H3C/Comware router or switch
Monitoring Examples
An administrator would poll hh3cTunnelIfTable/hh3cTunnelIfEntry to check hh3cTunnelIfEncapsMethod, hh3cTunnelIfLocalInetAddress, and hh3cTunnelIfRemoteInetAddress for each configured tunnel, confirming the tunnel uses the expected encapsulation and endpoints. Checking hh3cTunnelIfSecurity and hh3cTunnelIfHopLimit would reveal whether a tunnel has security enabled and whether its hop limit is misconfigured, while hh3cTunnelVxlanConfigGroup objects would be relevant for VXLAN-specific tunnels in a data center overlay.
What Can Be Monitored
- tunnel encapsulation method
- tunnel local/remote endpoint address
- tunnel hop limit
- tunnel security mode
- tunnel ToS/flow label settings
- VXLAN tunnel configuration
This MIB depends on
Related MIBs
Imported Objects
From HH3C-OID-MIB
| hh3cCommon | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero | |
| ifIndex | OBJECT-TYPE |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From IPV6-FLOW-LABEL-MIB
| IPv6FlowLabelOrAny |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hh3cTunnel | 1.3.6.1.4.1.25506.2.53 | This MIB contains objects to Manage configuration and Monitor tunnel. | ||
| hh3cTunnelMIBObjects | 1.3.6.1.4.1.25506.2.53.1 | |||
| hh3cTunnelTables | 1.3.6.1.4.1.25506.2.53.1.1 | |||
| hh3cTunnelIfTable | 1.3.6.1.4.1.25506.2.53.1.1.1 | not-accessible | The (conceptual) table containing information on configured tunnels. | |
| hh3cTunnelIfEntry | 1.3.6.1.4.1.25506.2.53.1.1.1.1 | not-accessible | An entry (conceptual row) containing the information on a particular configured tunnel. | |
| HH3 hh3cTunnelIfEncapsMethod | 1.3.6.1.4.1.25506.2.53.1.1.1.1.3 | Hh3cTunnelType | read-write | The encapsulation method used by the tunnel. |
| I32 hh3cTunnelIfHopLimit | 1.3.6.1.4.1.25506.2.53.1.1.1.1.4 | Integer32 | read-only | The IPv4 TTL or IPv6 Hop Limit to use in the outer IP header. A value of 0 indicates that the value is copied from the payload's header. |
| INT hh3cTunnelIfSecurity | 1.3.6.1.4.1.25506.2.53.1.1.1.1.5 | INTEGER | read-only | The method used by the tunnel to secure the outer IP header. The value ipsec indicates that IPsec is used between the tunnel endpoints for authentication or encryption or both. More specific security-related information may be available in a MIB module for the security protocol in use. |
| I32 hh3cTunnelIfTOS | 1.3.6.1.4.1.25506.2.53.1.1.1.1.6 | Integer32 | read-only | The method used to set the high 6 bits (the differentiated services codepoint) of the IPv4 TOS or IPv6 Traffic Class in the outer IP header. A value of -1 indicates that the bits are copied from the payload's header. A value of -2 indicates that a traffic conditioner is invoked and more information may be available in a traffic conditioner MIB module. A value between 0 and 63 inclusive indicates that the bit field is set to the indicated value. |
| IPV hh3cTunnelIfFlowLabel | 1.3.6.1.4.1.25506.2.53.1.1.1.1.7 | IPv6FlowLabelOrAny | read-only | The method used to set the IPv6 Flow Label value. This object need not be present in rows where hh3cTunnelIfAddressType indicates the tunnel is not over IPv6. A value of -1 indicates that a traffic conditioner is invoked and more information may be available in a traffic conditioner MIB. Any other value indicates that the Flow Label field is set to the indicated value. |
| IPt hh3cTunnelIfAddressType | 1.3.6.1.4.1.25506.2.53.1.1.1.1.8 | InetAddressType | read-write | The type of address in the corresponding hh3cTunnelIfLocalInetAddress and hh3cTunnelIfRemoteInetAddress objects. |
| IP hh3cTunnelIfLocalInetAddress | 1.3.6.1.4.1.25506.2.53.1.1.1.1.9 | InetAddress | read-write | The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header). If the address is unknown, the value is 0.0.0.0 for IPv4 or :: for IPv6. The type of this object is given by hh3cTunnelIfAddressType. |
| IP hh3cTunnelIfRemoteInetAddress | 1.3.6.1.4.1.25506.2.53.1.1.1.1.10 | InetAddress | read-write | The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header). If the address is unknown or the tunnel is not a point-to-point link (e.g., if it is a 6to4 tunnel), the value is 0.0.0.0 for tunnels over IPv4 or :: for tunnels over IPv6. The type of this object is given by hh3cTunnelIfAddressType. |
| I32 hh3cTunnelIfEncapsLimit | 1.3.6.1.4.1.25506.2.53.1.1.1.1.11 | Integer32 | read-only | The maximum number of additional encapsulations permitted for packets undergoing encapsulation at this node. A value of -1 indicates that no limit is present (except as a result of the packet size). |
| hh3cTunnelInetConfigTable | 1.3.6.1.4.1.25506.2.53.1.1.3 | not-accessible | The (conceptual) table containing information on configured tunnels. This table can be used to map a set of tunnel endpoints to the associated ifIndex value. It can also be used for row creation. Note that every row in the hh3cTunnelIfTable with a fixed destination address should have a corresponding row in the hh3cTunnelInetConfigTable, regardless of whether it was created via SNMP. | |
| hh3cTunnelInetConfigEntry | 1.3.6.1.4.1.25506.2.53.1.1.3.1 | not-accessible | An entry (conceptual row) containing the information on a particular configured tunnel. | |
| I32 hh3cTunnelInetConfigSlot | 1.3.6.1.4.1.25506.2.53.1.1.3.1.1 | Integer32 | not-accessible | Slot number. hh3cTunnelInetConfigSlot, hh3cTunnelInetConfigSubSlot and hh3cTunnelInetConfigTunnNum describe a tunnel interface. For Example, interface tunnel 0/0/25 would be configured as: hh3cTunnelInetConfigSlot 0 hh3cTunnelInetConfigSubSlot 0 hh3cTunnelInetConfigTunnNum 25 |
| I32 hh3cTunnelInetConfigSubSlot | 1.3.6.1.4.1.25506.2.53.1.1.3.1.2 | Integer32 | not-accessible | Sub slot number. As described in hh3cTunnelInetConfigSlot's description. |
| I32 hh3cTunnelInetConfigTunnNum | 1.3.6.1.4.1.25506.2.53.1.1.3.1.3 | Integer32 | not-accessible | Tunnel number. As described in hh3cTunnelInetConfigSlot's description. |
| NUM hh3cTunnelInetConfigIfIndex | 1.3.6.1.4.1.25506.2.53.1.1.3.1.6 | InterfaceIndexOrZero | read-only | If the value of hh3cTunnelInetConfigStatus for this row is active, then this object contains the value of ifIndex corresponding to the tunnel interface. A value of 0 is not legal in the active state, and means that the interface index has not yet been assigned. |
| ROW hh3cTunnelInetConfigStatus | 1.3.6.1.4.1.25506.2.53.1.1.3.1.7 | RowStatus | read-create | The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hh3cTunnelIfTable may be modified while this row is active. To create a row in this table, the management station should set hh3cTunnelInetConfigSlot, hh3cTunnelInetConfigSubSlot, hh3cTunnelInetConfigTunnNum, and set hh3cTunnelInetConfigStatus to createAndGo. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable and the hh3cTunnelIfTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable and in the hh3cTunnelIfTable. |
| hh3cTunnelEviTable | 1.3.6.1.4.1.25506.2.53.1.1.4 | not-accessible | The (conceptual) table containing information on configured EVI-Tunnel. | |
| hh3cTunnelEviEntry | 1.3.6.1.4.1.25506.2.53.1.1.4.1 | not-accessible | An entry (conceptual row) containing the information on a particular configured EVI-Tunnel. | |
| I32 hh3cTunnelEviTunnNum | 1.3.6.1.4.1.25506.2.53.1.1.4.1.1 | Integer32 | not-accessible | Tunnel number. An identifier used to distinguish between multiple tunnels. |
| NUM hh3cTunnelEviIfIndex | 1.3.6.1.4.1.25506.2.53.1.1.4.1.2 | InterfaceIndex | read-only | A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. |
| ROW hh3cTunnelEviStatus | 1.3.6.1.4.1.25506.2.53.1.1.4.1.3 | RowStatus | read-create | The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hh3cTunnelEviTable may be modified while this row is active. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable. |
| IPt hh3cTunnelEviAddressType | 1.3.6.1.4.1.25506.2.53.1.1.4.1.4 | InetAddressType | read-create | The type of address in the corresponding hh3cTunnelEviLocalAddr objects. Can not be modified after creation. |
| IP hh3cTunnelEviLocalAddr | 1.3.6.1.4.1.25506.2.53.1.1.4.1.5 | InetAddress | read-create | The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header). The type of this object is given by hh3cTunnelEviAddressType. |
| I32 hh3cTunnelEviNetworkID | 1.3.6.1.4.1.25506.2.53.1.1.4.1.6 | Integer32 | read-create | The method used to assign a network ID to an EVI-Tunnel interface. Assign the same network ID to the EVI-Tunnel interfaces of all edge devices in an EVI network. A value of 0 indicates that no network ID is assigned to any EVI-Tunnel interface. |
| I32 hh3cTunnelEviKeepaliveInterval | 1.3.6.1.4.1.25506.2.53.1.1.4.1.7 | Integer32 | read-create | The method used to assign the keepalive interval. |
| I32 hh3cTunnelEviKeepaliveTimes | 1.3.6.1.4.1.25506.2.53.1.1.4.1.8 | Integer32 | read-create | The method used to assign the keepalive maximum number of consecutive keepalive failures that are allowed. |
| hh3cTunnelEviLinkTable | 1.3.6.1.4.1.25506.2.53.1.1.5 | not-accessible | The (conceptual) table containing information on configured EVI-Link. | |
| hh3cTunnelEviLinkEntry | 1.3.6.1.4.1.25506.2.53.1.1.5.1 | not-accessible | An entry (conceptual row) containing the information on a particular configured EVI-Link. | |
| I32 hh3cTunnelEviLinkNum | 1.3.6.1.4.1.25506.2.53.1.1.5.1.1 | Integer32 | not-accessible | EVI-Link number. |
| NUM hh3cTunnelEviLinkIfIndex | 1.3.6.1.4.1.25506.2.53.1.1.5.1.2 | InterfaceIndex | read-only | A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. |
| IPt hh3cTunnelEviLinkAddressType | 1.3.6.1.4.1.25506.2.53.1.1.5.1.3 | InetAddressType | read-only | The type of address in the corresponding hh3cTunnelEviLinkRemoteAddr objects. Can not be modified after creation. |
| IP hh3cTunnelEviLinkRemoteAddr | 1.3.6.1.4.1.25506.2.53.1.1.5.1.4 | InetAddress | read-only | The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header). |
| hh3cTunnelGreTable | 1.3.6.1.4.1.25506.2.53.1.1.6 | not-accessible | The (conceptual) table containing information on configured Gre-Tunnel. | |
| hh3cTunnelGreEntry | 1.3.6.1.4.1.25506.2.53.1.1.6.1 | not-accessible | An entry (conceptual row) containing the information on a particular configured Gre-Tunnel. | |
| I32 hh3cTunnelGreTunnNum | 1.3.6.1.4.1.25506.2.53.1.1.6.1.1 | Integer32 | not-accessible | Tunnel number. An identifier used to distinguish between multiple tunnels. |
| NUM hh3cTunnelGreTunnIfIndex | 1.3.6.1.4.1.25506.2.53.1.1.6.1.2 | InterfaceIndex | read-only | A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. |
| IPt hh3cTunnelGreAddressType | 1.3.6.1.4.1.25506.2.53.1.1.6.1.3 | InetAddressType | read-create | The type of address in the corresponding hh3cTunnelGreLocalAddr and hh3cTunnelGreRemoteAddr objects. |
| IP hh3cTunnelGreLocalAddr | 1.3.6.1.4.1.25506.2.53.1.1.6.1.4 | InetAddress | read-create | The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header). |
| IP hh3cTunnelGreRemoteAddr | 1.3.6.1.4.1.25506.2.53.1.1.6.1.5 | InetAddress | read-create | The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header). |
| T/F hh3cTunnelGreKeepaliveEnabled | 1.3.6.1.4.1.25506.2.53.1.1.6.1.6 | TruthValue | read-create | This MIB object specifies whether or not keepalive is used. A value of true indicates that keepalive SHOULD be used. When keepalive is not be used, the value of hh3cTunnelGreKeepaliveInterval and hh3cTunnelGreKeepaliveTimes MUST be zero. |
| I32 hh3cTunnelGreKeepaliveInterval | 1.3.6.1.4.1.25506.2.53.1.1.6.1.7 | Integer32 | read-create | The method used to assign the keepalive interval. The value is zero when keepalive is not used. The valid value is from 1 to 32767, when keepalive is used. |
| I32 hh3cTunnelGreKeepaliveTimes | 1.3.6.1.4.1.25506.2.53.1.1.6.1.8 | Integer32 | read-create | The method used to assign the keepalive maximum number of consecutive keepalive failures that are allowed. The value is zero when keepalive is not used. The valid value is from 1 to 255, when keepalive is used. |
| U32 hh3cTunnelGreSlbgGroupNum | 1.3.6.1.4.1.25506.2.53.1.1.6.1.9 | Unsigned32 | read-create | The method used to assign the service-loopback-group. |
| ROW hh3cTunnelGreTunnStatus | 1.3.6.1.4.1.25506.2.53.1.1.6.1.10 | RowStatus | read-create | The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hh3cTunnelGreTable may be modified while this row is active. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable. |
| hh3cTunnelVxlanIfTable | 1.3.6.1.4.1.25506.2.53.1.1.7 | not-accessible | The (conceptual) table containing information on configured Vxlan-Tunnel. | |
| hh3cTunnelVxlanIfEntry | 1.3.6.1.4.1.25506.2.53.1.1.7.1 | not-accessible | An entry (conceptual row) containing the information on a particular configured Vxlan-Tunnel. | |
| I32 hh3cTunnelVxlanIfTunnNum | 1.3.6.1.4.1.25506.2.53.1.1.7.1.1 | Integer32 | not-accessible | Tunnel number. An identifier used to distinguish between multiple tunnels. |
| NUM hh3cTunnelVxlanTunnIfIndex | 1.3.6.1.4.1.25506.2.53.1.1.7.1.2 | InterfaceIndex | read-only | A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. |
| IPt hh3cTunnelVxlanIfAddressType | 1.3.6.1.4.1.25506.2.53.1.1.7.1.3 | InetAddressType | read-create | The type of address in the corresponding hh3cTunnelVxlanIfLocalAddr and hh3cTunnelVxlanIfRemoteAddr objects. |
| IP hh3cTunnelVxlanIfLocalAddr | 1.3.6.1.4.1.25506.2.53.1.1.7.1.4 | InetAddress | read-create | The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header). |
| IP hh3cTunnelVxlanIfRemoteAddr | 1.3.6.1.4.1.25506.2.53.1.1.7.1.5 | InetAddress | read-create | The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header). |
| ROW hh3cTunnelVxlanIfStatus | 1.3.6.1.4.1.25506.2.53.1.1.7.1.6 | RowStatus | read-create | The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hh3cTunnelVxlanIfTable may be modified while this row is active. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable. |
| hh3cTunnelVxlanConfigGroup | 1.3.6.1.4.1.25506.2.53.1.1.8 | |||
| I32 hh3cTunnelVxlanUdpPort | 1.3.6.1.4.1.25506.2.53.1.1.8.1 | Integer32 | read-write | The UDP port number for Vxlan Tunnels. |
| T/F hh3cTunnelVxlanDropWrongCksmPkt | 1.3.6.1.4.1.25506.2.53.1.1.8.2 | TruthValue | read-write | Whether or not dropping invalid UDP chesksum Vxlan packet. |
| T/F hh3cTunnelVxlanDropVlanTagPkt | 1.3.6.1.4.1.25506.2.53.1.1.8.3 | TruthValue | read-write | Whether or not dropping Vxlan packet with inner VLAN tag. |
| hh3cTunnelAvailableIDGroup | 1.3.6.1.4.1.25506.2.53.1.1.9 | |||
| I32 hh3cTunnelAvailableID | 1.3.6.1.4.1.25506.2.53.1.1.9.1 | Integer32 | read-only | The available tunnel ID. A value of -1 indicates that there is no available tunnel ID. |
| hh3cTunnelTotalNumTable | 1.3.6.1.4.1.25506.2.53.1.1.10 | not-accessible | Total number of a particular method tunnel. | |
| hh3cTunnelTotalNumEntry | 1.3.6.1.4.1.25506.2.53.1.1.10.1 | not-accessible | Total number of a particular method tunnel. | |
| HH3 hh3cTunnelEncapsMethod | 1.3.6.1.4.1.25506.2.53.1.1.10.1.1 | Hh3cTunnelType | not-accessible | The encapsulation method used by the tunnel. |
| U32 hh3cTunnelTotalNum | 1.3.6.1.4.1.25506.2.53.1.1.10.1.2 | Unsigned32 | read-only | Total number of a particular method tunnel. |
| hh3cTunnelNvgreIfTable | 1.3.6.1.4.1.25506.2.53.1.1.11 | not-accessible | The (conceptual) table containing information on configured Nvgre-Tunnel. | |
| hh3cTunnelNvgreIfEntry | 1.3.6.1.4.1.25506.2.53.1.1.11.1 | not-accessible | An entry (conceptual row) containing the information on a particular configured Nvgre-Tunnel. | |
| I32 hh3cTunnelNvgreIfTunnNum | 1.3.6.1.4.1.25506.2.53.1.1.11.1.1 | Integer32 | not-accessible | Tunnel number. An identifier used to distinguish between multiple tunnels. |
| NUM hh3cTunnelNvgreTunnIfIndex | 1.3.6.1.4.1.25506.2.53.1.1.11.1.2 | InterfaceIndex | read-only | A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. |
| IPt hh3cTunnelNvgreIfAddressType | 1.3.6.1.4.1.25506.2.53.1.1.11.1.3 | InetAddressType | read-create | The type of address in the corresponding hh3cTunnelNvgreIfLocalAddr and hh3cTunnelNvgreIfRemoteAddr objects. |
| IP hh3cTunnelNvgreIfLocalAddr | 1.3.6.1.4.1.25506.2.53.1.1.11.1.4 | InetAddress | read-create | The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header). |
| IP hh3cTunnelNvgreIfRemoteAddr | 1.3.6.1.4.1.25506.2.53.1.1.11.1.5 | InetAddress | read-create | The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header). |
| ROW hh3cTunnelNvgreIfStatus | 1.3.6.1.4.1.25506.2.53.1.1.11.1.6 | RowStatus | read-create | The status of this row, by which new entries may be created, or old entries deleted from this table. The agent need not support setting this object to createAndWait or notInService since there are no other writable objects in this table, and writable objects in rows of corresponding tables such as the hh3cTunnelNvgreIfTable may be modified while this row is active. Creating a row in this table will cause an interface index to be assigned by the agent in an implementation-dependent manner, and corresponding rows will be instantiated in the ifTable. The status of this row will become active as soon as the agent assigns the interface index, regardless of whether the interface is operationally up. Deleting a row in this table will likewise delete the corresponding row in the ifTable. |
RFC description
Manages GRE, L2TP, PPTP, 6to4 and other tunnel configuration on H3C devices.
Start monitoring H3C/Comware router or switch (GRE/IPsec/VXLAN tunnel interfaces) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.