All MIBs › HH3C-IPSEC-MONITOR-V2-MIB
Organization: Hangzhou H3C Tech. Co., Ltd.
Last Updated: 2012-06-27
Category: Domain: Security, VPN and Security, Vendor: H3C/HH3C
Description: Provides enhanced IPsec monitoring objects including SA lifetime and rekeying statistics on H3C VPN gateways.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HH3C-IPSEC-MONITOR-V2-MIB?
HH3C-IPSEC-MONITOR-V2-MIB is an H3C enterprise MIB providing enhanced monitoring of IPsec VPN tunnels on H3C security gateways/routers, an updated (v2) version of IPsec statistics reporting. It exposes per-tunnel and aggregate statistics such as security-association (SA) lifetime, rekeying counts, and traffic/error counters for established IPsec tunnels. Its core monitoring purpose is software/service (VPN tunnel) status and performance: tracking SA lifetime and rekey events reveals whether tunnels are renegotiating on schedule or failing repeatedly, and tunnel statistics show throughput/error levels, both key indicators of VPN health on the gateway. It complements the standard IPsec/IKE protocol stack and likely a v1 predecessor MIB on the same platform, explicitly stated to provide statistics for individual or all tunnels. Typical deployment is on H3C VPN gateways/firewalls terminating site-to-site or remote-access IPsec tunnels, where HH3C-IPSEC-MONITOR-V2-MIB SNMP monitoring tracks tunnel health and rekey activity.
IPNetwork Monitor allows you to monitor SNMP objects defined in HH3C-IPSEC-MONITOR-V2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- H3C VPN gateway/firewall with IPsec
Monitoring Examples
No specific objects were sampled for this MIB, so exact identifiers can't be cited, but consistent with its description an operator would poll per-tunnel SA lifetime and rekey-count objects to confirm a tunnel is successfully rekeying before expiry, and check aggregate or per-tunnel traffic/error counters to spot a tunnel with rising packet-drop or authentication-failure rates, which would indicate the far-end peer is misconfigured or the tunnel is under attack.
What Can Be Monitored
- IPsec SA lifetime
- rekeying count/events
- per-tunnel traffic statistics
- per-tunnel error/failure counters
- tunnel status (up/down)
This MIB depends on
Related MIBs
Imported Objects
From HH3C-OID-MIB
| hh3cCommon | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From RFC1213-MIB
| ifIndex |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using hh3cIPsecTunTotalRefreshesV2 OID:
Select an H3C VPN gateway/firewall (IPsec tunnel stats, v2) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hh3cIPsecTunTotalRefreshesV2 into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of security association refreshing performed. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hh3cIPsecMonitorV2 | 1.3.6.1.4.1.25506.2.126 | The MIB is designed to get statistic information of IPsec tunnels. With this MIB, we can get information of a certain tunnel or all tunnels. | ||
| hh3cIPsecObjectsV2 | 1.3.6.1.4.1.25506.2.126.1 | |||
| hh3cIPsecScalarObjectsV2 | 1.3.6.1.4.1.25506.2.126.1.1 | |||
| STR hh3cIPsecMIBVersion | 1.3.6.1.4.1.25506.2.126.1.1.1 | DisplayString | read-only | Version string of this MIB. |
| hh3cIPsecTunnelV2Table | 1.3.6.1.4.1.25506.2.126.1.2 | not-accessible | The IPsec Phase-2 Tunnel Table. There is one entry in this table for each active IPsec Phase-2 Tunnel. | |
| hh3cIPsecTunnelV2Entry | 1.3.6.1.4.1.25506.2.126.1.2.1 | not-accessible | Information about hh3cIPsecTunnelV2Table. | |
| I32 hh3cIPsecTunIndexV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.1 | Integer32 | accessible-for-notify | The index of IPsec Phase-2 Tunnel Table. The value of the index is a number which begins at one and is incremented with each tunnel that is created. The value of this object will wrap at 2147483647. |
| NUM hh3cIPsecTunIfIndexV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.2 | InterfaceIndex | read-only | The interface index( the ifIndex of ifTable ). |
| I32 hh3cIPsecTunIKETunnelIndexV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.3 | Integer32 | read-only | The index of the associated IPsec Phase-1 IKE Tunnel (IKETunIndex in the IKETunnelTable). 2147483647 is defined as invalid value. |
| HH3 hh3cIPsecTunIKETunLocalIDTypeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.4 | Hh3cIPsecIDTypeV2 | read-only | The type of the local peer identity for the associated IPsec Phase-1 IKE Tunnel (IKETunLocalType in the IKETunnelTable). |
| STR hh3cIPsecTunIKETunLocalIDVal1V2 | 1.3.6.1.4.1.25506.2.126.1.2.1.5 | DisplayString | read-only | The value of the local peer identity for the associated IPsec Phase-1 IKE Tunnel (IKETunLocalValue1 in the IKETunnelTable). If the local peer type is ipv4Addr/ipv6Addr, this is the IP address used to identify the local peer. If the local peer type is ipv4AddrSubnet/ipv6AddrSubnet, this is the subnet address. If the local peer type is ipv4AddrRange/ipv6AddrRange, this is the beginning IP address of the range. If the local peer type is fqdn/userFqdn, this is the host name used to identify the local peer. If the local peer type is derAsn1Dn, this is the binary DER encoding of an ASN.1 X.500 Distinguished Name [X.501] of the principal whose certificates are being exchanged to establish the SA. If the local peer type is derAsn1Gn, this is the binary DER encoding of an ASN.1 X.500 GeneralName [X.509] of the principal whose certificates are being exchanged to establish the SA. If the local peer type is keyId, this is an opaque byte stream which may be used to pass vendor-specific information necessary to identify which pre-shared key should be used to authenticate Aggressive mode negotiations. |
| STR hh3cIPsecTunIKETunLocalIDVal2V2 | 1.3.6.1.4.1.25506.2.126.1.2.1.6 | DisplayString | read-only | The second specification of the local peer's IP address for the associated IPsec Phase-1 IKE Tunnel (IKETunLocalValue2 in the IKETunnelTable). If the local peer type is ipv4AddrSubnet/ipv6AddrSubnet, this is the subnet mask. If the local peer type is ipv4AddrRange/ipv6AddrRange, this is the ending IP address of the range. If the local peer type is others, this is a zero-length string. |
| HH3 hh3cIPsecTunIKETunRemoteIDTypeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.7 | Hh3cIPsecIDTypeV2 | read-only | The type of the remote peer identity for the associated IPsec Phase-1 IKE Tunnel (IKETunRemoteType in the IKETunnelTable). |
| STR hh3cIPsecTunIKETunRemoteIDVal1V2 | 1.3.6.1.4.1.25506.2.126.1.2.1.8 | DisplayString | read-only | The value of the remote peer identity for the associated IPsec Phase-1 IKE Tunnel (IKETunRemoteValue1 in the IKETunnelTable). If the remote peer type is ipv4Addr/ipv6Addr, this is the IP address used to identify the remote peer. If the remote peer type is ipv4AddrSubnet/ipv6AddrSubnet, this is the subnet address. If the remote peer type is ipv4AddrRange/ipv6AddrRange, this is the beginning IP address of the range. If the remote peer type is fqdn/userFqdn, this is the host name used to identify the remote peer. If the remote peer type is derAsn1Dn, this is the binary DER encoding of an ASN.1 X.500 Distinguished Name [X.501] of the principal whose certificates are being exchanged to establish the SA. If the remote peer type is derAsn1Gn, this is the binary DER encoding of an ASN.1 X.500 GeneralName [X.509] of the principal whose certificates are being exchanged to establish the SA. If the remote peer type is keyId, this is an opaque byte stream which may be used to pass vendor-specific information necessary to identify which pre-shared key should be used to authenticate Aggressive mode negotiations. |
| STR hh3cIPsecTunIKETunRemoteIDVal2V2 | 1.3.6.1.4.1.25506.2.126.1.2.1.9 | DisplayString | read-only | The second specification of the remote peer's IP address for the associated IPsec Phase-1 IKE Tunnel(IKETunRemoteValue2 in the IKETunnelTable). If the remote peer type is ipv4AddrSubnet/ipv6AddrSubnet, this is the subnet mask. If the remote peer type is ipv4AddrRange/ipv6AddrRange, this is the ending IP address of the range. If the remote peer type is others, this is a zero-length string. |
| IPt hh3cIPsecTunLocalAddrTypeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.10 | InetAddressType | read-only | The type of the IP address for the local peer of the IPsec Phase-2 Tunnel. |
| IP hh3cIPsecTunLocalAddrV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.11 | InetAddress | read-only | The IP address of the local peer for the IPsec Phase-2 Tunnel. |
| IPt hh3cIPsecTunRemoteAddrTypeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.12 | InetAddressType | read-only | The type of the IP address for the remote peer of the IPsec Phase-2 Tunnel. |
| IP hh3cIPsecTunRemoteAddrV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.13 | InetAddress | read-only | The IP address of the remote peer for the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecTunKeyTypeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.14 | Hh3cIPsecNegoTypeV2 | read-only | The key negotiate mode used by the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecTunEncapModeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.15 | Hh3cIPsecEncapModeV2 | read-only | The encapsulation mode used by the IPsec Phase-2 Tunnel. |
| INT hh3cIPsecTunInitiatorV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.16 | INTEGER | read-only | The initiator of this IPsec tunnel. Value none is used for manual IPsec tunnel, for there is no initiator or responder in this method. |
| G32 hh3cIPsecTunLifeSizeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.17 | Gauge32 | read-only | The negotiated LifeSize of the IPsec Phase-2 Tunnel in kilobytes. 0 is defined as invalid value. |
| I32 hh3cIPsecTunLifeTimeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.18 | Integer32 | read-only | The negotiated LifeTime of the IPsec Phase-2 Tunnel in seconds. 2147483647 is defined as invalid value. |
| I32 hh3cIPsecTunRemainTimeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.19 | Integer32 | read-only | The remain time of SA in seconds. 2147483647 is defined as invalid value. |
| I32 hh3cIPsecTunActiveTimeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.20 | Integer32 | read-only | The duration the IPsec Phase-2 Tunnel has been active in hundredths of seconds. 2147483647 is defined as invalid value. |
| G32 hh3cIPsecTunRemainSizeV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.21 | Gauge32 | read-only | The remain LifeSize of SA in kilobytes. 0 is defined as invalid value. |
| C32 hh3cIPsecTunTotalRefreshesV2Ex | 1.3.6.1.4.1.25506.2.126.1.2.1.22 | Counter32 | read-only | The total number of security association refreshing performed. |
| G32 hh3cIPsecTunCurrentSaInstancesV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.23 | Gauge32 | read-only | The number of security associations which are currently active or expiring. |
| HH3 hh3cIPsecTunInSaEncryptAlgoV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.24 | Hh3cIPsecEncryptAlgoV2 | read-only | The encryption algorithm used by the inbound security association of the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecTunInSaAhAuthAlgoV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.25 | Hh3cIPsecAuthAlgoV2 | read-only | The authentication algorithm used by the inbound authentication header (AH) security association of the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecTunInSaEspAuthAlgoV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.26 | Hh3cIPsecAuthAlgoV2 | read-only | The authentication algorithm used by the inbound encapsulation security protocol(ESP) security association of the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecTunDiffHellmanGrpV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.27 | Hh3cIPsecDiffHellmanGrpV2 | read-only | The Diffie Hellman Group used by the security association of the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecTunOutSaEncryptAlgoV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.28 | Hh3cIPsecEncryptAlgoV2 | read-only | The encryption algorithm used by the outbound security association of the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecTunOutSaAhAuthAlgoV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.29 | Hh3cIPsecAuthAlgoV2 | read-only | The authentication algorithm used by the outbound authentication header (AH) security association of the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecTunOutSaEspAuthAlgoV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.30 | Hh3cIPsecAuthAlgoV2 | read-only | The authentication algorithm used by the outbound encapsulation security protocol(ESP) security association of the IPsec Phase-2 Tunnel. |
| STR hh3cIPsecTunPolicyNameV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.31 | DisplayString | read-only | The policy name used by this IPsec tunnel. |
| I32 hh3cIPsecTunPolicyNumV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.32 | Integer32 | read-only | The sequence number of policy used by this IPsec tunnel. |
| INT hh3cIPsecTunStatusV2 | 1.3.6.1.4.1.25506.2.126.1.2.1.33 | INTEGER | read-only | The status of the IPsec Tunnel. |
| hh3cIPsecTunnelStatV2Table | 1.3.6.1.4.1.25506.2.126.1.3 | not-accessible | The IPsec Phase-2 Tunnel Statistics Table. | |
| hh3cIPsecTunnelStatV2Entry | 1.3.6.1.4.1.25506.2.126.1.3.1 | not-accessible | Information about hh3cIPsecTunnelStatV2Table. | |
| C64 hh3cIPsecTunInOctetsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.1 | Counter64 | read-only | The total number of octets received by this IPsec Phase-2 Tunnel. This value is accumulated BEFORE determining whether or not the packet should be decompressed. |
| C64 hh3cIPsecTunInDecompOctetsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.2 | Counter64 | read-only | The total number of decompressed octets received by this IPsec Phase-2 Tunnel. This value is accumulated AFTER the packet is decompressed. |
| C64 hh3cIPsecTunInPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.3 | Counter64 | read-only | The total number of packets received by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunInDropPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.4 | Counter64 | read-only | The total number of packets dropped during receiving process by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunInReplayDropPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.5 | Counter64 | read-only | The total number of packets dropped during receiving process due to Anti-Replay process by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunInAuthFailsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.6 | Counter64 | read-only | The total number of inbound authentication's which ended in failure by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunInDecryptFailsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.7 | Counter64 | read-only | The total number of inbound decryption's which ended in failure by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunOutOctetsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.8 | Counter64 | read-only | The total number of octets sent by this IPsec Phase-2 Tunnel. This value is accumulated AFTER determining whether or not the packet should be compressed. |
| C64 hh3cIPsecTunOutUncompOctetsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.9 | Counter64 | read-only | The total number of uncompressed octets sent by this IPsec Phase-2 Tunnel. This value is accumulated BEFORE the packet is compressed. |
| C64 hh3cIPsecTunOutPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.10 | Counter64 | read-only | The total number of packets sent by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunOutDropPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.11 | Counter64 | read-only | The total number of packets dropped during sending process by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunOutEncryptFailsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.12 | Counter64 | read-only | The total number of outbound encryption's which ended in failure by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunNoMemoryDropPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.13 | Counter64 | read-only | The total number of packets dropped due to no enough memory by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunQueueFullDropPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.14 | Counter64 | read-only | The total number of packets dropped due to queue full by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunInvalidLenDropPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.15 | Counter64 | read-only | The total number of packets dropped due to invalid length packet by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunTooLongDropPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.16 | Counter64 | read-only | The total number of packets dropped due to too long packet by this IPsec Phase-2 Tunnel. |
| C64 hh3cIPsecTunInvalidSaDropPktsV2 | 1.3.6.1.4.1.25506.2.126.1.3.1.17 | Counter64 | read-only | The total number of packets dropped due to invalid SA by this IPsec Phase-2 Tunnel. |
| hh3cIPsecSaV2Table | 1.3.6.1.4.1.25506.2.126.1.4 | not-accessible | The IPsec Phase-2 Security Protection Index Table. This table contains an entry for each active and expiring security association. | |
| hh3cIPsecSaV2Entry | 1.3.6.1.4.1.25506.2.126.1.4.1 | not-accessible | Information about hh3cIPsecSaV2Table. | |
| I32 hh3cIPsecSaIndexV2 | 1.3.6.1.4.1.25506.2.126.1.4.1.1 | Integer32 | accessible-for-notify | The number of the Sa associated with the Phase-2 Tunnel Table. The value of this index is a number which begins at one and is incremented with each Sa associated with an IPsec Phase-2 Tunnel. The value of this object will wrap at 2,147,483,647. |
| INT hh3cIPsecSaDirectionV2 | 1.3.6.1.4.1.25506.2.126.1.4.1.2 | INTEGER | read-only | The direction of the SA. |
| U32 hh3cIPsecSaSpiValueV2 | 1.3.6.1.4.1.25506.2.126.1.4.1.3 | Unsigned32 | read-only | The value of the SPI. |
| HH3 hh3cIPsecSaSecProtocolV2 | 1.3.6.1.4.1.25506.2.126.1.4.1.4 | Hh3cIPsecSaProtocolV2 | read-only | The security protocol of the SA. |
| HH3 hh3cIPsecSaEncryptAlgoV2 | 1.3.6.1.4.1.25506.2.126.1.4.1.5 | Hh3cIPsecEncryptAlgoV2 | read-only | The encryption algorithm used by the security association of the IPsec Phase-2 Tunnel. |
| HH3 hh3cIPsecSaAuthAlgoV2 | 1.3.6.1.4.1.25506.2.126.1.4.1.6 | Hh3cIPsecAuthAlgoV2 | read-only | The authentication algorithm used by the SA. |
| INT hh3cIPsecSaStatusV2 | 1.3.6.1.4.1.25506.2.126.1.4.1.7 | INTEGER | read-only | The status of the SA. |
| hh3cIPsecTrafficV2Table | 1.3.6.1.4.1.25506.2.126.1.5 | not-accessible | The IPsec Phase-2 Tunnel Traffic Table. | |
| hh3cIPsecTrafficV2Entry | 1.3.6.1.4.1.25506.2.126.1.5.1 | not-accessible | Information about hh3cIPsecTrafficV2Table. | |
| HH3 hh3cIPsecTrafficLocalTypeV2 | 1.3.6.1.4.1.25506.2.126.1.5.1.1 | Hh3cIPsecTrafficTypeV2 | read-only | The type of the local peer's traffic. Possible values are: 1) A single IP address 2) An IP address range 3) An IP subnet |
| IPt hh3cIPsecTrafficLocalAddr1TypeV2 | 1.3.6.1.4.1.25506.2.126.1.5.1.2 | InetAddressType | read-only | The type of the first IP address specification for the local peer's traffic. |
| IP hh3cIPsecTrafficLocalAddr1V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.3 | InetAddress | read-only | The first IP address specification of the local peer's traffic. If the local peer's traffic type is single IP address, this is the IP address. If the local peer's traffic type is IP subnet, this is the subnet address. If the local peer's traffic type is IP address range, this is the beginning IP address of the range. |
| IPt hh3cIPsecTrafficLocalAddr2TypeV2 | 1.3.6.1.4.1.25506.2.126.1.5.1.4 | InetAddressType | read-only | The type of the second IP address specification for the local peer's traffic. |
| IP hh3cIPsecTrafficLocalAddr2V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.5 | InetAddress | read-only | The second IP address specification of the local peer's traffic. If the local peer's traffic type is single IP address, this is the IP address. If the local peer's traffic type is IP subnet, this is the subnet mask. If the local peer's traffic type is IP address range, this is the ending IP address of the range. |
| I32 hh3cIPsecTrafficLocalProtocol1V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.6 | Integer32 | read-only | The first protocol number specification of the local peer's traffic. If the protocol type of the local peer's traffic is single protocol, this is the protocol number. If the protocol type of the local peer's traffic is protocol range, this is the beginning protocol number of the range. |
| I32 hh3cIPsecTrafficLocalProtocol2V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.7 | Integer32 | read-only | The second protocol number specification of the local peer's traffic. If the protocol type of the local peer's traffic is single protocol, this is the protocol number. If the protocol type of the local peer's traffic is protocol range, this is the ending protocol number of the range. |
| I32 hh3cIPsecTrafficLocalPort1V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.8 | Integer32 | read-only | The first port number specification of the local peer's traffic. If the port type of the local peer's traffic is single port, this is the port number. If the port type of the local peer's traffic is port range, this is the beginning port number of the range. |
| I32 hh3cIPsecTrafficLocalPort2V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.9 | Integer32 | read-only | The second port number specification of the local peer's traffic. If the port type of the local peer's traffic is single port, this is the port number. If the port type of the local peer's traffic is port range, this is the ending port number of the range. |
| HH3 hh3cIPsecTrafficRemoteTypeV2 | 1.3.6.1.4.1.25506.2.126.1.5.1.10 | Hh3cIPsecTrafficTypeV2 | read-only | The type of the remote peer's traffic. Possible values are: 1) A single IP address 2) An IP address range 3) An IP subnet |
| IPt hh3cIPsecTrafficRemAddr1TypeV2 | 1.3.6.1.4.1.25506.2.126.1.5.1.11 | InetAddressType | read-only | The type of the first IP address specification for the remote peer's traffic. |
| IP hh3cIPsecTrafficRemAddr1V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.12 | InetAddress | read-only | The first IP address specification of the remote peer's traffic. If the remote traffic type is single IP address, this is the IP address. If the remote traffic type is IP subnet, this is the subnet address. If the remote traffic type is IP address range, this is the beginning IP address of the range. |
| IPt hh3cIPsecTrafficRemAddr2TypeV2 | 1.3.6.1.4.1.25506.2.126.1.5.1.13 | InetAddressType | read-only | The type of the second IP address specification for the remote peer's traffic. |
| IP hh3cIPsecTrafficRemAddr2V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.14 | InetAddress | read-only | The second IP address specification of the remote peer's traffic. If the remote traffic type is single IP address, this is the IP address. If the remote traffic type is IP subnet, this is the subnet mask. If the remote traffic type is IP address range, this is the ending IP address of the range. |
| I32 hh3cIPsecTrafficRemoPro1V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.15 | Integer32 | read-only | The first protocol number specification of the remote peer's traffic. If the protocol type of the remote peer's traffic is single protocol, this is the protocol number. If the protocol type of the remote peer's traffic is protocol range, this is the beginning protocol number of the range. |
| I32 hh3cIPsecTrafficRemoPro2V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.16 | Integer32 | read-only | The second protocol number specification of the remote peer's traffic. If the protocol type of the remote peer's traffic is single protocol, this is the protocol number. If the protocol type of the remote peer's traffic is protocol range, this is the ending protocol number of the range. |
| I32 hh3cIPsecTrafficRemPort1V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.17 | Integer32 | read-only | The first port number specification of the remote peer's traffic. If the port type of the remote peer's traffic is single port, this is the port number. If the port type of the remote peer's traffic is port range, this is the beginning port number of the range. |
| I32 hh3cIPsecTrafficRemPort2V2 | 1.3.6.1.4.1.25506.2.126.1.5.1.18 | Integer32 | read-only | The second port number specification of the remote peer's traffic. If the port type of the remote peer's traffic is single port, this is the port number. If the port type of the remote peer's traffic is port range, this is the ending port number of the range. |
| hh3cIPsecGlobalStatsV2 | 1.3.6.1.4.1.25506.2.126.1.6 | |||
| G32 hh3cIPsecGlobalActiveTunnelsV2 | 1.3.6.1.4.1.25506.2.126.1.6.1 | Gauge32 | read-only | The total number of currently active IPsec Phase-2 Tunnels. |
| G32 hh3cIPsecGlobalActiveSasV2 | 1.3.6.1.4.1.25506.2.126.1.6.2 | Gauge32 | read-only | The total number of currently active or expiring IPsec Phase-2 SA. |
| C64 hh3cIPsecGlobalInOctetsV2 | 1.3.6.1.4.1.25506.2.126.1.6.3 | Counter64 | read-only | The total number of octets received by all current and previous IPsec Phase-2 Tunnels. This value is accumulated BEFORE determining whether or not the packet should be decompressed. |
| C64 hh3cIPsecGlobalInDecompOctetsV2 | 1.3.6.1.4.1.25506.2.126.1.6.4 | Counter64 | read-only | The total number of decompressed octets received by all current and previous IPsec Phase-2 Tunnels. This value is accumulated AFTER the packet is decompressed. |
| C64 hh3cIPsecGlobalInPktsV2 | 1.3.6.1.4.1.25506.2.126.1.6.5 | Counter64 | read-only | The total number of packets received by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalInDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.6 | Counter64 | read-only | The total number of packets dropped during receiving process by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalInReplayDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.7 | Counter64 | read-only | The total number of packets dropped during receiving process due to Anti-Replay process by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalInAuthFailsV2 | 1.3.6.1.4.1.25506.2.126.1.6.8 | Counter64 | read-only | The total number of inbound authentication's which ended in failure by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalInDecryptFailsV2 | 1.3.6.1.4.1.25506.2.126.1.6.9 | Counter64 | read-only | The total number of inbound decryption's which ended in failure by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalOutOctetsV2 | 1.3.6.1.4.1.25506.2.126.1.6.10 | Counter64 | read-only | The total number of octets sent by all current and previous IPsec Phase-2 Tunnels. This value is accumulated AFTER determining whether or not the packet should be compressed. |
| C64 hh3cIPsecGlobalOutUncompOctetsV2 | 1.3.6.1.4.1.25506.2.126.1.6.11 | Counter64 | read-only | The total number of uncompressed octets sent by all current and previous IPsec Phase-2 Tunnels. This value is accumulated BEFORE the packet is compressed. |
| C64 hh3cIPsecGlobalOutPktsV2 | 1.3.6.1.4.1.25506.2.126.1.6.12 | Counter64 | read-only | The total number of packets sent by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalOutDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.13 | Counter64 | read-only | The total number of packets dropped during sending process by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalOutEncryptFailsV2 | 1.3.6.1.4.1.25506.2.126.1.6.14 | Counter64 | read-only | The total number of outbound encryption's which ended in failure by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalNoMemoryDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.15 | Counter64 | read-only | The total number of packets dropped due to no enough memory by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalNoFindSaDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.16 | Counter64 | read-only | The total number of packets dropped due to not find SA by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalQueueFullDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.17 | Counter64 | read-only | The total number of packets dropped due to queue full by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalInvalidLenDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.18 | Counter64 | read-only | The total number of packets dropped due to invalid packet length by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalTooLongDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.19 | Counter64 | read-only | The total number of packets dropped due to too long packet by all current and previous IPsec Phase-2 Tunnels. |
| C64 hh3cIPsecGlobalInvalidSaDropsV2 | 1.3.6.1.4.1.25506.2.126.1.6.20 | Counter64 | read-only | The total number of packets dropped due to invalid SA by all current and previous IPsec Phase-2 Tunnels. |
| hh3cIPsecTrapObjectV2 | 1.3.6.1.4.1.25506.2.126.1.7 | |||
| STR hh3cIPsecPolicyNameV2 | 1.3.6.1.4.1.25506.2.126.1.7.1 | DisplayString | accessible-for-notify | The IPsec policy name with a trap. |
| I32 hh3cIPsecPolicySeqNumV2 | 1.3.6.1.4.1.25506.2.126.1.7.2 | Integer32 | accessible-for-notify | The IPsec policy sequence number with a trap. |
| I32 hh3cIPsecPolicySizeV2 | 1.3.6.1.4.1.25506.2.126.1.7.3 | Integer32 | accessible-for-notify | The number of IPsec policies with a trap. |
| hh3cIPsecTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8 | |||
| T/F hh3cIPsecTrapGlobalCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.1 | TruthValue | read-write | Indicates whether all IPsec traps should be generated. |
| T/F hh3cIPsecTunnelStartTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.2 | TruthValue | read-write | Indicates whether hh3cIPsecTunnelStartV2 traps should be generated. |
| T/F hh3cIPsecTunnelStopTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.3 | TruthValue | read-write | Indicates whether hh3cIPsecTunnelStopV2 traps should be generated. |
| T/F hh3cIPsecNoSaTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.4 | TruthValue | read-write | Indicates whether hh3cIPsecNoSaFailureV2 traps should be generated. |
| T/F hh3cIPsecAuthFailureTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.5 | TruthValue | read-write | Indicates whether hh3cIPsecAuthFailFailureV2 traps should be generated. |
| T/F hh3cIPsecEncryFailureTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.6 | TruthValue | read-write | Indicates whether hh3cIPsecEncryFailFailureV2 traps should be generated. |
| T/F hh3cIPsecDecryFailureTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.7 | TruthValue | read-write | Indicates whether hh3cIPsecDecryFailFailureV2 traps should be generated. |
| T/F hh3cIPsecInvalidSaTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.8 | TruthValue | read-write | Indicates whether hh3cIPsecInvalidSaFailureV2 traps should be generated. |
| T/F hh3cIPsecPolicyAddTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.9 | TruthValue | read-write | Indicates whether hh3cIPsecPolicyAddV2 traps should be generated. |
| T/F hh3cIPsecPolicyDelTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.10 | TruthValue | read-write | Indicates whether hh3cIPsecPolicyDelV2 traps should be generated. |
| T/F hh3cIPsecPolicyAttachTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.11 | TruthValue | read-write | Indicates whether hh3cIPsecPolicyAttachV2 traps should be generated. |
| T/F hh3cIPsecPolicyDetachTrapCntlV2 | 1.3.6.1.4.1.25506.2.126.1.8.12 | TruthValue | read-write | Indicates whether hh3cIPsecPolicyDetachV2 traps should be generated. |
| hh3cIPsecTrapV2 | 1.3.6.1.4.1.25506.2.126.1.9 | |||
| hh3cIPsecNotificationsV2 | 1.3.6.1.4.1.25506.2.126.1.9.0 | |||
| NTF hh3cIPsecTunnelStartV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.1 | This notification is generated when an IPsec Phase-2 Tunnel is created. | ||
| NTF hh3cIPsecTunnelStopV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.2 | This notification is generated when an IPsec Phase-2 Tunnel is deleted. | ||
| NTF hh3cIPsecNoSaFailureV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.3 | This notification is generated when an IPsec Phase-2 non-existent SA error occurs. | ||
| NTF hh3cIPsecAuthFailFailureV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.4 | This notification is generated when the IPsec phase-2 authentication failure occurs. | ||
| NTF hh3cIPsecEncryFailFailureV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.5 | This notification is generated when the IPsec phase-2 tunnel has an encrypting failure. | ||
| NTF hh3cIPsecDecryFailFailureV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.6 | This notification is generated when the IPsec phase-2 tunnel has a decrypting failure. | ||
| NTF hh3cIPsecInvalidSaFailureV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.7 | This notification is generated when the IPsec phase-2 invalid SA failure occurs. | ||
| NTF hh3cIPsecPolicyAddV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.8 | This notification is generated when an IPsec policy is added. | ||
| NTF hh3cIPsecPolicyDelV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.9 | This notification is generated when an IPsec policy is deleted. | ||
| NTF hh3cIPsecPolicyAttachV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.10 | This notification is generated when an IPsec policy is attached with one interface. | ||
| NTF hh3cIPsecPolicyDetachV2 | 1.3.6.1.4.1.25506.2.126.1.9.0.11 | This notification is generated when an IPsec policy is detached with one interface. | ||
| hh3cIPsecConformanceV2 | 1.3.6.1.4.1.25506.2.126.2 | |||
| hh3cIPsecCompliancesV2 | 1.3.6.1.4.1.25506.2.126.2.1 | |||
| hh3cIPsecComplianceV2 | 1.3.6.1.4.1.25506.2.126.2.1.1 | |||
| hh3cIPsecGroupsV2 | 1.3.6.1.4.1.25506.2.126.2.2 | |||
| hh3cIPsecScalarObjectsGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.1 | The group contains all of scalar objects of the MIB. | ||
| hh3cIPsecTunnelTableGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.2 | The group contains the IPsec tunnel's property information. | ||
| hh3cIPsecTunnelStatGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.3 | The group contains the IPsec tunnel's statistic information. | ||
| hh3cIPsecSaGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.4 | The group contains the SA's property information. | ||
| hh3cIPsecTrafficTableGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.5 | The group contains the property information of the data flow protected by IPsec tunnel. | ||
| hh3cIPsecGlobalStatsGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.6 | The group contains all of the IPsec tunnel's statistic information. | ||
| hh3cIPsecTrapObjectGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.7 | The group contains all of trap objects of IPsec tunnels. | ||
| hh3cIPsecTrapCntlGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.8 | The group contains all of trap switches of IPsec tunnels. | ||
| hh3cIPsecTrapGroupV2 | 1.3.6.1.4.1.25506.2.126.2.2.9 | The group contains all of trap of IPsec tunnels. |
RFC description
H3C IPsec tunnel statistics and monitoring MIB providing tunnel information, encryption algorithms, and Diffie-Hellman group details.
Start monitoring H3C VPN gateway/firewall (IPsec tunnel stats, v2) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.