HH3C-EPON-UNI-MIB

All MIBs › HH3C-EPON-UNI-MIB

Organization: Hangzhou H3C Technologies Co., Ltd.

Last Updated: 2008-07-28

Category: Technology: EPON/PON, Vendor: H3C/HH3C

Description: Manages EPON User Network Interface (UNI) port parameters and service mappings on H3C ONU devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HH3C-EPON-UNI-MIB?

HH3C-EPON-UNI-MIB is a Hangzhou H3C Technologies proprietary MIB managing and displaying configuration of an EPON UNI (User Network Interface) on an ONU (Optical Network Unit). Its system-management table, keyed by index, records description, admin status, MDI mode, priority, VLAN type, access VLAN, trunk PVID, VLAN trunk-allow-list low/high, inbound/outbound line rate, flow control, speed, duplex, VLAN-VPN status, a count-reset action, port-isolate flag, VLAN configuration, auto-negotiation, a restart-auto-neg action, link status, and interface type. As a configuration/status MIB it lets an administrator confirm VLAN and rate-limiting configuration on an EPON subscriber-facing UNI port. It is deployed on H3C EPON ONU subscriber equipment. Engineers can download the HH3C-EPON-UNI-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HH3C-EPON-UNI-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C EPON ONU subscriber equipment

Monitoring Examples

An administrator checks hh3cEponUniAccessVlan and hh3cEponUniInboundLineRate to confirm VLAN and rate-limit settings on an EPON UNI port on H3C ONU equipment.

What Can Be Monitored

EPON UNI VLAN and rate-limit configuration

Imported Objects

From HH3C-OID-MIB

hh3cEpon

OBJECT-IDENTITY

From IF-MIB

ifDescr	OBJECT-TYPE
ifIndex	OBJECT-TYPE

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hh3cEponUni	1.3.6.1.4.1.25506.2.42.5			The objects in this MIB module are used to manage and display current configuration of UNI (user network interface) which is based on the ONU(Optical Network Unit).
hh3cEponUniSysMan	1.3.6.1.4.1.25506.2.42.5.1
hh3cEponUniSysManTable	1.3.6.1.4.1.25506.2.42.5.1.1		not-accessible	This table defines several UNI system parameters.
hh3cEponUniSysManEntry	1.3.6.1.4.1.25506.2.42.5.1.1.1		not-accessible	The entry of hh3cEponUniSysManTable.
I32 hh3cEponUniIndex	1.3.6.1.4.1.25506.2.42.5.1.1.1.1	Integer32	accessible-for-notify	The index value which uniquely identifies the FE(fast Ethernet) interface of the ONU.
OCT hh3cEponUniDescr	1.3.6.1.4.1.25506.2.42.5.1.1.1.2	OCTET STRING	read-only	A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware and software.
INT hh3cEponUniAdminStatus	1.3.6.1.4.1.25506.2.42.5.1.1.1.3	INTEGER	read-write	The desired state of the user network interface. When a managed system initializes, all user network interfaces start with down(2) state. The testing(3)state indicates that no operational packets can be passed. As a result of either explicit management action or per configuration information retained by the managed system, hh3cEponUniAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
INT hh3cEponUniMdi	1.3.6.1.4.1.25506.2.42.5.1.1.1.4	INTEGER	read-write	Type of the line connected to UNI interface: mdi-ii(straight-through cable), mdi-x (crossover cable), mdi-auto (auto-sensing).
I32 hh3cEponUniPriority	1.3.6.1.4.1.25506.2.42.5.1.1.1.5	Integer32	read-write	The priority of user network interface. If the value is larger, the priority will be higher.
INT hh3cEponUniVlanType	1.3.6.1.4.1.25506.2.42.5.1.1.1.6	INTEGER	read-write	UNI vlan types.
I32 hh3cEponUniAccessVlan	1.3.6.1.4.1.25506.2.42.5.1.1.1.7	Integer32	read-write	The vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
INT hh3cEponUniTrunkPvid	1.3.6.1.4.1.25506.2.42.5.1.1.1.8	INTEGER	read-write	PVID(port vlan ID), the vlan ID assigned to untagged frames or Priority-Tagged frames received on user network interface.
OCT hh3cEponUniVLANTrunkAllowListLow	1.3.6.1.4.1.25506.2.42.5.1.1.1.9	OCTET STRING	read-write	Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans. the vlan is not allowed if its bit has a value of '0'.
OCT hh3cEponUniVLANTrunkAllowListHigh	1.3.6.1.4.1.25506.2.42.5.1.1.1.10	OCTET STRING	read-write	Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 2049 through 2056, the second octet specifying vlans 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered vlan, and the least significant bit represents the lowest numbered vlan. Thus, each allowed vlan of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is allowed in the set of vlans; the vlan is not allowed if its bit has a value of '0'.
I32 hh3cEponUniInboundLineRate	1.3.6.1.4.1.25506.2.42.5.1.1.1.11	Integer32	read-write	The value of the inbound line-rate. measured with kbps. The upper limit of the line-rate is the value of hh3cEponUniLineRateMax in the entry. It must be multiple of the value of hh3cEponUniLineRateStep. The default value of hh3cEponUniLineRate is the value of hh3cEponUniLineRateMax.
I32 hh3cEponUniOutboundLineRate	1.3.6.1.4.1.25506.2.42.5.1.1.1.12	Integer32	read-write	The value of the outbound line-rate. measured with kbps. The upper limit of the line-rate is the value of hh3cEponUniLineRateMax in the entry. It must be multiple of the value of hh3cEponUniLineRateStep. The default value of hh3cEponUniLineRate is the value of hh3cEponUniLineRateMax.
T/F hh3cEponUniFlowControl	1.3.6.1.4.1.25506.2.42.5.1.1.1.13	TruthValue	read-write	Flow control status. true(1) - Flow control status enable. false(2) - Flow control status disable.
INT hh3cEponUniSpeed	1.3.6.1.4.1.25506.2.42.5.1.1.1.14	INTEGER	read-write	User network interface speed.
INT hh3cEponUniDuplex	1.3.6.1.4.1.25506.2.42.5.1.1.1.15	INTEGER	read-write	User network interface mode.
T/F hh3cEponUniVlanVPNStatus	1.3.6.1.4.1.25506.2.42.5.1.1.1.16	TruthValue	read-write	vlan VPN status. true(1) - vlan VPN status enable. false(2) - vlan VPN disable.
INT hh3cEponUniCountReset	1.3.6.1.4.1.25506.2.42.5.1.1.1.17	INTEGER	read-write	Reset the counter which is about packets of the interface, then the counter will change to zero. There is no sense in reading this object.
INT hh3cEponUniPortIsolate	1.3.6.1.4.1.25506.2.42.5.1.1.1.18	INTEGER	read-write	enable - enable UNI port isolate setting. disable - disable UNI port isolate setting.
OCT hh3cEponUniVlanConfiguration	1.3.6.1.4.1.25506.2.42.5.1.1.1.23	OCTET STRING	read-write	The vlan configuration of the related vlan mode. Transparent vlan mode: hh3cEponUniVlanConfiguration is a zero length string. Tag vlan mode: the first four octets were the tag assigned to untagged frames received on UNI, including TPID, VID,CFI and priority. Translation vlan mode: the first four octets were the old tag (including TPID, VID, CFI and priority), which is replaced by the new tag(including TPID, VID, CFI and priority), the second four octets.
INT hh3cEponUniAutoNegotiation	1.3.6.1.4.1.25506.2.42.5.1.1.1.25	INTEGER	read-write	enable - enable auto negotiation. disable - disable auto negotiation.
INT hh3cEponUniRestartAutoNeg	1.3.6.1.4.1.25506.2.42.5.1.1.1.26	INTEGER	read-write	Force to restart the auto negotiation process.
INT hh3cEponUniLinkStatus	1.3.6.1.4.1.25506.2.42.5.1.1.1.29	INTEGER	read-only	The link status of UNI.
INT hh3cEponUniInterfaceType	1.3.6.1.4.1.25506.2.42.5.1.1.1.30	INTEGER	read-only	UNI interface type.
INT hh3cEponUniVitualCableTest	1.3.6.1.4.1.25506.2.42.5.1.1.1.31	INTEGER	read-write	True(1): Virtual cable test enable. False(2): Virtual cable test disable.
INT hh3cEponUniVCTCableStatus	1.3.6.1.4.1.25506.2.42.5.1.1.1.32	INTEGER	read-only	Get the cable status. Normal(1),cable is normal. Abnormal(2),cable is abnormal. AbnormalOpen(3),cable is abnormal because of open circuit. AbnormalShort(4),cable is abnormal because of short circuit. Failure(5),cable is abnormal because of testing failure.
I32 hh3cEponUniVCTCableLength	1.3.6.1.4.1.25506.2.42.5.1.1.1.33	Integer32	read-only	Get the cable length. When hh3cEponUniVCTCableStatus is normal, the node stands for the length from the UNI port to the port opposite. When hh3cEponUniVCTCableStatus is abnormal, it stands for the lengh from the UNI port to the failure place. Unit:meter(m).
INT hh3cEponUniVCTImpedanceMismatch	1.3.6.1.4.1.25506.2.42.5.1.1.1.34	INTEGER	read-only	Get the cable impedance. Not-support(1),the UNI port does not support this function. True(2),impedance match. False(3),impedance mismatch.
I32 hh3cEponUniVCTPairSkew	1.3.6.1.4.1.25506.2.42.5.1.1.1.35	Integer32	read-only	Get the symmetry of cable. If the function is not supported , the default value 0 will be returned. Unit:nanosecond(ns).
INT hh3cEponUniVCTPairSwap	1.3.6.1.4.1.25506.2.42.5.1.1.1.36	INTEGER	read-only	NotSupport(1),the UNI port does not support this function. True(2),pair swap. False(3),not pair swap.
INT hh3cEponUniVCTPolaritySwap	1.3.6.1.4.1.25506.2.42.5.1.1.1.37	INTEGER	read-only	NotSupport(1),the UNI port does not support this function. True(2),polarity swap. False(3),not polarity swap.
I32 hh3cEponUniVCTInsertionLoss	1.3.6.1.4.1.25506.2.42.5.1.1.1.38	Integer32	read-only	If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
I32 hh3cEponUniVCTReturnLoss	1.3.6.1.4.1.25506.2.42.5.1.1.1.39	Integer32	read-only	If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
I32 hh3cEponUniVCTNearendCrosstalk	1.3.6.1.4.1.25506.2.42.5.1.1.1.40	Integer32	read-only	If the function is not supported , the default value 0 will be returned. Unit:decibel(db).
hh3cEponUniCountTable	1.3.6.1.4.1.25506.2.42.5.1.2		not-accessible	A list of interface counter about frames entries.
hh3cEponUniCountEntry	1.3.6.1.4.1.25506.2.42.5.1.2.1		not-accessible	An entry containing management information applicable to a particular interface.
U32 hh3cEponUniInStatsPkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.1	Unsigned32	read-only	The total number of frames (including bad frames, broadcast frames, and multicast frames) received.
U32 hh3cEponUniInStatsUnicastPkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.2	Unsigned32	read-only	The total number of good frames received that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
U32 hh3cEponUniInStatsBroadcastPkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.3	Unsigned32	read-only	The total number of good frames received that are directed to the broadcast address. Note that this does not include multicast frames.
U32 hh3cEponUniInStatsMulticastPkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.4	Unsigned32	read-only	The total number of good frames received that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
U32 hh3cEponUniInPausePkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.5	Unsigned32	read-only	A count of MAC Control frames received on this interface by the pause(flow control) operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
U32 hh3cEponUniInTotalErrors	1.3.6.1.4.1.25506.2.42.5.1.2.1.6	Unsigned32	read-only	Total count of the error frames received on this interface.
U32 hh3cEponUniInStatsCRCAlignErrors	1.3.6.1.4.1.25506.2.42.5.1.2.1.7	Unsigned32	read-only	The total number of frames received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
U32 hh3cEponUniInStatsUndersizePkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.8	Unsigned32	read-only	The total number of frames received that are less than 64 octets long (excluding framing bits, but including FCS octets) and are otherwise well formed.
U32 hh3cEponUniInStatsOversizePkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.9	Unsigned32	read-only	The total number of frames received that are longer than 1518 octets (excluding framing bits, but including FCS octets) and are otherwise well formed.
U32 hh3cEponUniInErrorbyOther	1.3.6.1.4.1.25506.2.42.5.1.2.1.10	Unsigned32	read-only	The total number of error frames received on this interface.
U32 hh3cEponUniOutStatsPkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.11	Unsigned32	read-only	The total number of frames (including bad frames, broadcast frames, and multicast frames) sent.
U32 hh3cEponUniOutStatsUnicastPkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.12	Unsigned32	read-only	The total number of good frames sent that are directed to the unicast address. Note that this does not include multicast and broadcast frames.
U32 hh3cEponUniOutStatsBroadcastPkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.13	Unsigned32	read-only	The total number of good frames sent that are directed to the broadcast address. Note that this does not include multicast frames.
U32 hh3cEponUniOutStatsMulticastPkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.14	Unsigned32	read-only	The total number of good frames sent that are directed to a multicast address. Note that this number does not include frames directed to the broadcast address.
U32 hh3cEponUniOutStatsPausePkts	1.3.6.1.4.1.25506.2.42.5.1.2.1.15	Unsigned32	read-only	The total number of MAC control frames sent on this interface by the pause operation. This counter does not increment when the interface is in a half-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system.
U32 hh3cEponUniOutTotalErrors	1.3.6.1.4.1.25506.2.42.5.1.2.1.16	Unsigned32	read-only	The total number of error frames sent on this interface.
U32 hh3cEponUniOutStatsCollisions	1.3.6.1.4.1.25506.2.42.5.1.2.1.17	Unsigned32	read-only	The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment could. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
U32 hh3cEponUniOutDelayExceededDiscards	1.3.6.1.4.1.25506.2.42.5.1.2.1.18	Unsigned32	read-only	The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
U32 hh3cEponUniOutErrorbyOther	1.3.6.1.4.1.25506.2.42.5.1.2.1.19	Unsigned32	read-only	The total number of other error frames sent on this interface. Other error frames means the error frames out of collision frames and excessive delayed frames.
U32 hh3cEponUniOutDroppedFrames	1.3.6.1.4.1.25506.2.42.5.1.2.1.20	Unsigned32	read-only	The total number of frames dropped because of buffer failure.
hh3cEponUniIgmpInfoTable	1.3.6.1.4.1.25506.2.42.5.1.3		not-accessible	This table stores igmp information of UNI interface.
hh3cEponUniIgmpInfoEntry	1.3.6.1.4.1.25506.2.42.5.1.3.1		not-accessible	The entry of hh3cEponUniIgmpInfoTable.
I32 hh3cEponUniMacIndex	1.3.6.1.4.1.25506.2.42.5.1.3.1.1	Integer32	not-accessible	The index uniquely identifies the igmp information in current UNI interface.
MAC hh3cEponUniIgmpMacAddress	1.3.6.1.4.1.25506.2.42.5.1.3.1.2	MacAddress	read-only	A 6-octet read-only value carrying the individual MAC address indicates which igmp group the UNI interface belonging to.
I32 hh3cEponUniIgmpVlanId	1.3.6.1.4.1.25506.2.42.5.1.3.1.3	Integer32	read-only	An integer range from 1 to 4094 indicates the vlan which the igmp Mac address has joined in.
hh3cEponUniParaMan	1.3.6.1.4.1.25506.2.42.5.1.4
I32 hh3cEponUniLineRateMax	1.3.6.1.4.1.25506.2.42.5.1.4.1	Integer32	read-only	The maximum value of the line-rate(kbps) that user network interface can be set.
I32 hh3cEponUniLineRateStep	1.3.6.1.4.1.25506.2.42.5.1.4.2	Integer32	read-only	The step of line-rate(kbps).
I32 hh3cEponUniNumberOnOnu	1.3.6.1.4.1.25506.2.42.5.1.4.3	Integer32	read-only	The user network interface number on ONU.
hh3cEponUniScalarGroup	1.3.6.1.4.1.25506.2.42.5.1.5
hh3cEponUniPortPolicyTable	1.3.6.1.4.1.25506.2.42.5.1.6		not-accessible	UNI port policy configuration.
hh3cEponUniPortPolicyEntry	1.3.6.1.4.1.25506.2.42.5.1.6.1		not-accessible	The entry of hh3cEponUniPortPolicyTable.
INT hh3cEponUniPortPolicyStatus	1.3.6.1.4.1.25506.2.42.5.1.6.1.1	INTEGER	read-write	enable - enable UNI upstream port policing. disable - disable UNI upstream port policing.
I32 hh3cEponUniPortPolicyCir	1.3.6.1.4.1.25506.2.42.5.1.6.1.2	Integer32	read-write	The committed information rate, ranging from 1 to 102400, measured in kbps.
I32 hh3cEponUniPortPolicyBucketDepth	1.3.6.1.4.1.25506.2.42.5.1.6.1.3	Integer32	read-write	The depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
I32 hh3cEponUniPortPolicyExtraBurst	1.3.6.1.4.1.25506.2.42.5.1.6.1.4	Integer32	read-write	The extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
I32 hh3cEponUniPortPolicyInboundCir	1.3.6.1.4.1.25506.2.42.5.1.6.1.5	Integer32	read-write	The inbound committed information rate, measured in kbps.
I32 hh3cEponUniPortPolicyInboundBucketDepth	1.3.6.1.4.1.25506.2.42.5.1.6.1.6	Integer32	read-write	The inbound depth of the token bucket to tolerant the certain burst(CBS), ranging from 0 to 65535, measured in bytes.
I32 hh3cEponUniPortPolicyInboundExtraBurst	1.3.6.1.4.1.25506.2.42.5.1.6.1.7	Integer32	read-write	The inbound extra token to permit the forwarding engine to finish the packet being sent when the bucket depth is exhausted, ranging from 0 to 65535, measured in bytes.
I32 hh3cEponUniPortPolicyOutboundCir	1.3.6.1.4.1.25506.2.42.5.1.6.1.8	Integer32	read-write	The outbound committed information rate, stepped by 64, measured in kbps.
I32 hh3cEponUniPortPolicyOutboundPir	1.3.6.1.4.1.25506.2.42.5.1.6.1.9	Integer32	read-write	The outbound peak information rate, stepped by 64, measured in kbps.
hh3cEponUniMulticastTable	1.3.6.1.4.1.25506.2.42.5.1.7		not-accessible	UNI multicast configuration.
hh3cEponUniMulticastEntry	1.3.6.1.4.1.25506.2.42.5.1.7.1		not-accessible	The entry of hh3cEponUniPortPolicyTable.
I32 hh3cEponUniMulticastGroupNumber	1.3.6.1.4.1.25506.2.42.5.1.7.1.1	Integer32	read-write	The allowed multicast group number that can be handled at the same time by UNI.
OCT hh3cEponUniMulticastVlanList	1.3.6.1.4.1.25506.2.42.5.1.7.1.2	OCTET STRING	read-write	The multicast vlan list. The first two octets of the string represent the first VLAN ID; the second two octets of the string represent the second VLAN ID, and so on. It is a zero length string by default.
INT hh3cEponUniMulticastStripStatus	1.3.6.1.4.1.25506.2.42.5.1.7.1.3	INTEGER	read-write	true - strip the vlan tag of multicast packet. false - does not strip the vlan tag of multicast packet.
T/F hh3cEponUniMulticastFastleave	1.3.6.1.4.1.25506.2.42.5.1.7.1.4	TruthValue	read-write	true(1) - fast leave of IGMP enable on ONU. false(2) - fast leave of IGMP disable on ONU.
hh3cEponUniTechAbilityTable	1.3.6.1.4.1.25506.2.42.5.1.8		not-accessible	UNI multicast configuration.
hh3cEponUniTechAbilityEntry	1.3.6.1.4.1.25506.2.42.5.1.8.1		not-accessible	The entry of hh3cEponUniTechAbilityTable.
OCT hh3cEponUniLocalTechAbility	1.3.6.1.4.1.25506.2.42.5.1.8.1.1	OCTET STRING	read-only	The local port capabilities of the UNI. Each two octets stand for a capability of UNI: the first two octets represent one capability and the second two octets represent another capability, and so on. The capabilities list: 1 - undefined, 2 - initializing, true ability not yet known, 14 - 10BASE-T, 142 - full duplex 10BASE-T, 23 - 100BASE-T4, 25 - 100BASE-TX, 252 - full duplex 100BASE-TX, 312 - PAUSE operation for full duplex links, 313 - asymmetric PAUSE operation for full duplex links, 314 - symmetric PAUSE operation for full duplex links, 32 - 100BASE-T2, 322 - full duplex 100BASE-T2, 36 - 1000BASE-X, 362 - full duplex 1000BASE-X, 40 - 1000BASE-T UTP PHY, 402 - full duplex 1000BASE-T UTP PHY, 37 - remote fault bit 1(RF1), 372 - remote fault bit 2(RF2), 8029 - 802.9ISLAN-16T.
OCT hh3cEponUniAdvertisedTechAbility	1.3.6.1.4.1.25506.2.42.5.1.8.1.2	OCTET STRING	read-only	The advertised port capabilities of the UNI. The capabilities list references the description of hh3cEponUniLocalTechAbility.
hh3cEponUniMulticastControlTable	1.3.6.1.4.1.25506.2.42.5.1.9		not-accessible	UNI multicast control parameters.
hh3cEponUniMulticastControlEntry	1.3.6.1.4.1.25506.2.42.5.1.9.1		not-accessible	The entry of the table hh3cEponUniMulticastControlTable.
I32 hh3cEponUniMulticastVlanIndex	1.3.6.1.4.1.25506.2.42.5.1.9.1.1	Integer32	read-create	The multicast vlan ID.
OCT hh3cEponUniMulticastAddressList	1.3.6.1.4.1.25506.2.42.5.1.9.1.2	OCTET STRING	read-create	The multicast address, each four octets represents a multicast address, the address section ranging from the first four octets to the second four octets, and the like.
INT hh3cEponUniMulticastAccessRule	1.3.6.1.4.1.25506.2.42.5.1.9.1.3	INTEGER	read-create	deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
I32 hh3cEponUniMulticastChannelLimit	1.3.6.1.4.1.25506.2.42.5.1.9.1.4	Integer32	read-create	The limitation of multicast preview channel number.
I32 hh3cEponUniMulticastPreTimeSlice	1.3.6.1.4.1.25506.2.42.5.1.9.1.5	Integer32	read-create	The time slice of multicast preview.
I32 hh3cEponUniMulticastPreTimes	1.3.6.1.4.1.25506.2.42.5.1.9.1.6	Integer32	read-create	The number of multicast preview times.
I32 hh3cEponUniMulticastPreInterval	1.3.6.1.4.1.25506.2.42.5.1.9.1.7	Integer32	read-create	The interval between two consecutive previews, measured in minute.
ROW hh3cEponUniMulticastRowStatus	1.3.6.1.4.1.25506.2.42.5.1.9.1.8	RowStatus	read-create	The status of this table entry. The active, createAndGo and the destory statuses are supported.
INT hh3cEponUniMulticastIndex	1.3.6.1.4.1.25506.2.42.5.1.9.1.9	INTEGER	not-accessible	The index of the entry.
OCT hh3cEponUniMulticastSourceIpList	1.3.6.1.4.1.25506.2.42.5.1.9.1.10	OCTET STRING	read-create	This list contains many source ip addresses. Each ip address is contained in four octets.
I32 hh3cEponUniMulticastResetInterval	1.3.6.1.4.1.25506.2.42.5.1.9.1.11	Integer32	read-create	The interval is measured in minute. From the last preview limitation is reached, a customer can preview again after this interval is expired.
hh3cEponUniQosIndexNextTable	1.3.6.1.4.1.25506.2.42.5.1.10		not-accessible	The next index table.
hh3cEponUniQosIndexNextEntry	1.3.6.1.4.1.25506.2.42.5.1.10.1		not-accessible	The entry of the table hh3cEponUniQosIndexNextTable.
I32 hh3cEponUniQosConfIndexNext	1.3.6.1.4.1.25506.2.42.5.1.10.1.1	Integer32	read-only	This object contains an appropriate value to be used for hh3cEponUniQosConfIndex when creating rows in the hh3cEponUniQosConfTable.
hh3cEponUniQosConfTable	1.3.6.1.4.1.25506.2.42.5.1.11		not-accessible	UNI Qos configuration.
hh3cEponUniQosConfEntry	1.3.6.1.4.1.25506.2.42.5.1.11.1		not-accessible	The entry of the table hh3cEponUniQosConfTable.
I32 hh3cEponUniQosConfIndex	1.3.6.1.4.1.25506.2.42.5.1.11.1.1	Integer32	not-accessible	The rule index.
I32 hh3cEponUniQosConfRuleIndexNext	1.3.6.1.4.1.25506.2.42.5.1.11.1.2	Integer32	read-only	This object contains an appropriate value to be used for hh3cEponUniQosRuleIndex when creating rows in the hh3cEponUniQosRuleTable.
I32 hh3cEponUniQosConfMappedQueue	1.3.6.1.4.1.25506.2.42.5.1.11.1.3	Integer32	read-create	The queue that the ethernet frames will be mapped.
I32 hh3cEponUniQosConfMarkedPriority	1.3.6.1.4.1.25506.2.42.5.1.11.1.4	Integer32	read-create	Priority of the ethernet frames to be marked, which compliant with the 802.1D user priority standard.
ROW hh3cEponUniQosConfRowStatus	1.3.6.1.4.1.25506.2.42.5.1.11.1.5	RowStatus	read-create	The status of this table entry. The active, createAndGo and the destory statuses are supported.
hh3cEponUniQosRuleTable	1.3.6.1.4.1.25506.2.42.5.1.12		not-accessible	Qos sub rule of the UNI.
hh3cEponUniQosRuleEntry	1.3.6.1.4.1.25506.2.42.5.1.12.1		not-accessible	The entry of the table hh3cEponUniQosRuleTable.
I32 hh3cEponUniQosRuleIndex	1.3.6.1.4.1.25506.2.42.5.1.12.1.1	Integer32	not-accessible	The sub rule index.
INT hh3cEponUniQosRuleSelector	1.3.6.1.4.1.25506.2.42.5.1.12.1.2	INTEGER	read-create	The ethernet frame selector. dstmac - based on destination MAC address. srcmac - based on source MAC address. ethernetpriority - based on ethernet priority. vlanid - based on VLAN ID. ethernettype - based on ethernet type. dstip - based on destination IP address. srcip - based on source IP address. ipprototype - based on IP type(ipv4 or ipv6). ipv4tosdscp - based on IP TOS/DSCP. ipv6 - based IP precedence. srcport - based on layer 4 source port. dstport - based on layer 4 destination port.
I32 hh3cEponUniQosRuleValue	1.3.6.1.4.1.25506.2.42.5.1.12.1.3	Integer32	read-create	The rule value based on the hh3cEponUniQosRuleSelector.
MAC hh3cEponUniQosRuleMacAddress	1.3.6.1.4.1.25506.2.42.5.1.12.1.4	MacAddress	read-create	MAC Address.
INT hh3cEponUniQosRuleOperator	1.3.6.1.4.1.25506.2.42.5.1.12.1.5	INTEGER	read-create	nervermatch - value never match. equal - field equal to the value. notequal - field not equal to the value. lessthanequal - field less than or equal to the value. greaterthanequal - field greater than or equal to the value. fieldexist - value is ignored if field exists. fieldnotexist - value is ignored if field does not exist. alwaysmatch - value always match.
ROW hh3cEponUniQosRuleRowStatus	1.3.6.1.4.1.25506.2.42.5.1.12.1.6	RowStatus	read-create	The status of this table entry. Only active, createAndGo and the destory are supported.
hh3cEponUniMirrorGroupTable	1.3.6.1.4.1.25506.2.42.5.1.13		not-accessible	Qos sub rule of the UNI.
hh3cEponUniMirrorGroupEntry	1.3.6.1.4.1.25506.2.42.5.1.13.1		not-accessible	The entry of the hh3cEponUniMirrorGroupTable.
I32 hh3cEponUniMirrorGroupID	1.3.6.1.4.1.25506.2.42.5.1.13.1.1	Integer32	not-accessible	Epon UNI mirror group ID.
OCT hh3cEponUniMirrorInboundPortList	1.3.6.1.4.1.25506.2.42.5.1.13.1.2	OCTET STRING	read-write	UNI inbound port list. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered UNI, and the least significant bit represents the lowest numbered UNI. Thus, each UNI port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is allowed in the set of ports. the port is not allowed if its bit has a value of '0'.
OCT hh3cEponUniMirrorOutboundPortList	1.3.6.1.4.1.25506.2.42.5.1.13.1.3	OCTET STRING	read-create	UNI outnbound port list, more infomation reference hh3cEponUniMirrorInboundPortList
I32 hh3cEponUniMonitorPort	1.3.6.1.4.1.25506.2.42.5.1.13.1.4	Integer32	read-create	UNI monitor port.
ROW hh3cEponUniMirrorRowStatus	1.3.6.1.4.1.25506.2.42.5.1.13.1.5	RowStatus	read-create	RowStatus, Now support three status: createAndGo, active, destroy.
hh3cEponUniMirrorGroupIdNextTable	1.3.6.1.4.1.25506.2.42.5.1.14		not-accessible	The next index table, which is used by hh3cEponUniMirrorGroupTable.
hh3cEponUniMirrorGroupIdNextEntry	1.3.6.1.4.1.25506.2.42.5.1.14.1		not-accessible	The entry of the table hh3cEponUniMirrorGroupIdNextEntry.
I32 hh3cEponUniMirrorGroupIDNext	1.3.6.1.4.1.25506.2.42.5.1.14.1.1	Integer32	read-only	This object contains an appropriate value to be used for hh3cEponUniMirrorGroupID when creating rows in the hh3cEponUniMirrorGroupTable.
hh3cEponUniMulticastCtrlInfoTable	1.3.6.1.4.1.25506.2.42.5.1.15		not-accessible	UNI multicast information which is active .
hh3cEponUniMulticastCtrlInfoEntry	1.3.6.1.4.1.25506.2.42.5.1.15.1		not-accessible	The entry of the table hh3cEponUniMulticastCtrlInfoTable.
I32 hh3cEponUniMultActVlan	1.3.6.1.4.1.25506.2.42.5.1.15.1.1	Integer32	not-accessible	The multicast vlan ID which is active.
IP hh3cEponUniMultActAddress	1.3.6.1.4.1.25506.2.42.5.1.15.1.2	IpAddress	not-accessible	The multicast address which is active.
INT hh3cEponUniMultActAccessRule	1.3.6.1.4.1.25506.2.42.5.1.15.1.3	INTEGER	read-only	deny - deny the multicast packet. permit - permit the multicast packet. preview - permit the multicast packet with conditions.
I32 hh3cEponUniMultActPreTimes	1.3.6.1.4.1.25506.2.42.5.1.15.1.4	Integer32	read-only	The number of multicast preview times which is active.
I32 hh3cEponUniMultActPreRemain	1.3.6.1.4.1.25506.2.42.5.1.15.1.5	Integer32	read-only	The remanent time slice of multicast preview which is active.
hh3cEponUniMulticastIndexNextTable	1.3.6.1.4.1.25506.2.42.5.1.16		not-accessible	The next index table, which is used by hh3cEponUniMulticastControlTable.
hh3cEponUniMulticastIndexNextEntry	1.3.6.1.4.1.25506.2.42.5.1.16.1		not-accessible	The entry of the table hh3cEponUniMulticastIndexNextEntry.
I32 hh3cEponUniMulticastConfIndexNext	1.3.6.1.4.1.25506.2.42.5.1.16.1.1	Integer32	read-only	This object contains an appropriate value to be used for hh3cEponUniMulticastIndex when creating rows in the hh3cEponUniMulticastControlTable.
hh3cEponUniTrap	1.3.6.1.4.1.25506.2.42.5.2
hh3cEponUniTrapPrefix	1.3.6.1.4.1.25506.2.42.5.2.0
NTF hh3cEponUniLinkUpTrap	1.3.6.1.4.1.25506.2.42.5.2.0.1			A hh3cEponUniLinkUpTrap notification is sent when the UNI up event is detected and the transmitting switch is turned on.
NTF hh3cEponUniLinkDownTrap	1.3.6.1.4.1.25506.2.42.5.2.0.2			A hh3cEponUniLinkDownTrap notification is sent when the UNI down event is detected and the transmitting switch is turned on.

RFC description

H3C EPON UNI (User Network Interface) MIB for managing EPON port configuration, QoS, multicast, and link status.

Start monitoring H3C EPON ONU subscriber equipment (UNI port config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HH3C-EPON-UNI-MIB

What Is HH3C-EPON-UNI-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description