HH3C-DOT11-RRM-MIB

All MIBs › HH3C-DOT11-RRM-MIB

Organization: Hangzhou H3C Technologies Co., Ltd.

Last Updated: 2010-09-25

Category: Technology: Wireless, Vendor: H3C/HH3C

Description: Manages 802.11 Radio Resource Management (RRM) including channel, power, and coverage optimization on H3C APs.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HH3C-DOT11-RRM-MIB?

HH3C-DOT11-RRM-MIB is an H3C enterprise MIB for Radio Resource Management (RRM) on wireless LAN access points, covering automatic channel selection, transmit-power adjustment, coverage optimization, and interference/spectrum management for 802.11a/g/n radios. It exposes per-radio configuration and status such as channel-scan intervals, transmit power constraints, MCS (modulation and coding scheme) capability settings, and interference-count thresholds. Its monitoring value lies in wireless RF health: tracking interference counts at the AP and station level, scan-report activity, and auto-channel-avoidance behavior lets an admin detect congested channels, interference sources, or coverage holes affecting Wi-Fi service quality - effectively continuous software/RF-status monitoring of each radio. It is a WLAN-controller-side MIB that complements H3C's broader dot11 MIB family (AP/radio inventory and client-association MIBs) for a full picture of WLAN hardware/software status. It is deployed on H3C wireless LAN controllers managing fleets of access points in enterprise/campus Wi-Fi networks. Engineers can download the HH3C-DOT11-RRM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HH3C-DOT11-RRM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C wireless LAN controller
H3C 802.11 access point

Monitoring Examples

hh3cDot11RRMRadioCfgTable/hh3cDot11RRMRadioCfgEntry lets an admin inspect and set per-radio RRM parameters, while hh3cDot11RRMScanChl and hh3cDot11RRMScanRptIntvel control how often APs scan neighboring channels and report back, useful for detecting channel congestion. hh3cDot11APInterfNumThreshhd and hh3cDot11StaInterfNumThreshhd define interference-count thresholds at the AP and station level respectively - a sustained count above threshold flags an interference or coverage problem on a particular radio. hh3cDot11RRM11gProtect and hh3cDot11RRM11aPwrConstrt reveal 802.11g protection mode and 802.11a transmit-power constraints, which an admin would check when diagnosing throughput drops caused by legacy-client protection overhead or regulatory power limiting.

What Can Be Monitored

channel scan interval/report frequency
AP and station interference thresholds
transmit power constraints
802.11g protection mode
MCS capability settings
auto channel-avoidance activity

Imported Objects

From HH3C-DOT11-REF-MIB

Hh3cDot11ChannelScopeType
Hh3cDot11ObjectIDType
Hh3cDot11RadioElementIndex
Hh3cDot11RadioScopeType
Hh3cDot11RadioType
Hh3cDot11SSIDStringType
hh3cDot11	MODULE-IDENTITY
hh3cDot11APElementIndex	OBJECT-TYPE

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
MacAddress
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
I32 hh3cDot11APInterfNumThreshhd	1.3.6.1.4.1.25506.2.75.8.1.1.9	Integer32	read-write	Represents threshold of AP interference . If the value of AP interference exceeds this threshold, AP interference trap will be sent. If the value of this node is zero, AP interference trap will be sent immediately.
hh3cDot11MonitorDetectedDevEntry	1.3.6.1.4.1.25506.2.75.8.4.1.1		not-accessible	Each entry contains information of detected devices.
hh3cDot11MonitorDetectedDevTable	1.3.6.1.4.1.25506.2.75.8.4.1		not-accessible	This table shows the devices of AP detected
hh3cDot11MonitorDetectedGroup	1.3.6.1.4.1.25506.2.75.8.4
I32 hh3cDot11MonitorDevBeaconIntvl	1.3.6.1.4.1.25506.2.75.8.4.1.1.9	Integer32	read-only	Represents the beacon interval for the detected device(not include the device which type is client).
MAC hh3cDot11MonitorDevBSSID	1.3.6.1.4.1.25506.2.75.8.4.1.1.5	MacAddress	read-only	Represents the basic service set identifier of the detected device.
HH3 hh3cDot11MonitorDevChannel	1.3.6.1.4.1.25506.2.75.8.4.1.1.6	Hh3cDot11ChannelScopeType	read-only	Represents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is interference between adjacent channels.
T/F hh3cDot11MonitorDevClear	1.3.6.1.4.1.25506.2.75.8.4.1.1.12	TruthValue	read-write	This object is used to clear the information of the device detected in the WLAN. It will return false for get operation.
DAT hh3cDot11MonitorDevFstDctTime	1.3.6.1.4.1.25506.2.75.8.4.1.1.10	DateAndTime	read-only	Represents the time at which the device was first detected.
DAT hh3cDot11MonitorDevLstDctTime	1.3.6.1.4.1.25506.2.75.8.4.1.1.11	DateAndTime	read-only	Represents the time at which the device was detected last time.
MAC hh3cDot11MonitorDevMAC	1.3.6.1.4.1.25506.2.75.8.4.1.1.1	MacAddress	not-accessible	Represents MAC address of the device detected.
I32 hh3cDot11MonitorDevMaxRSSI	1.3.6.1.4.1.25506.2.75.8.4.1.1.8	Integer32	read-only	Represents the maximum detected RSSI of the device in a scan report cycle.
I32 hh3cDot11MonitorDevSNR	1.3.6.1.4.1.25506.2.75.8.4.1.1.13	Integer32	read-only	Represents the SNR of the device in a scan report cycle.
OCT hh3cDot11MonitorDevSSID	1.3.6.1.4.1.25506.2.75.8.4.1.1.4	OCTET STRING	read-only	Represents the service set identifier for the ESS of the device which type is ap or adhoc.
INT hh3cDot11MonitorDevType	1.3.6.1.4.1.25506.2.75.8.4.1.1.2	INTEGER	read-only	Represents type of the device detected.
OCT hh3cDot11MonitorDevVendor	1.3.6.1.4.1.25506.2.75.8.4.1.1.3	OCTET STRING	read-only	Represents vendor of the detected device.
HH3 hh3cDot11MonitorRadioId	1.3.6.1.4.1.25506.2.75.8.4.1.1.7	Hh3cDot11RadioScopeType	read-only	Represents the radio ID of the AP that detected the device.
I32 hh3cDot11NewPower	1.3.6.1.4.1.25506.2.75.8.3.3.1	Integer32	accessible-for-notify	Power of the radio after the change of power.
I32 hh3cDot11OldPower	1.3.6.1.4.1.25506.2.75.8.3.3.2	Integer32	accessible-for-notify	Power of the radio before the change of power.
hh3cDot11RRM	1.3.6.1.4.1.25506.2.75.8			This MIB file is to provide the object definition of WLAN radio resource management (RRM).
I32 hh3cDot11RRM11aPwrConstrt	1.3.6.1.4.1.25506.2.75.8.1.1.4	Integer32	read-write	Configure the power constraint for all 802.11a radios. The configured power constraint is advertised in beacons if spectrum management is enabled. The range of power constraint is 0 to MAX-POWER-1 (where the MAX-POWER is defined by the regulatory domain).
T/F hh3cDot11RRM11aSpectrumManag	1.3.6.1.4.1.25506.2.75.8.1.1.5	TruthValue	read-write	Enable/Disable spectrum management for 802.11a radios. When spectrum management is enabled, the WLAN sub-system advertises power capabilities of the AP and power constraints applicable to all devices in the BSS based on regulatory domain specification.
T/F hh3cDot11RRM11gProtect	1.3.6.1.4.1.25506.2.75.8.1.1.3	TruthValue	read-write	Enable/Disable dot11g protection.
I32 hh3cDot11RRM11nMadtMaxMcs	1.3.6.1.4.1.25506.2.75.8.1.1.1	Integer32	read-write	Specify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No maximum MCS index is specified for 802.11n mandatory rates by default. Besides 255, the specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.
I32 hh3cDot11RRM11nSuptMaxMcs	1.3.6.1.4.1.25506.2.75.8.1.1.2	Integer32	read-write	Specify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.
I32 hh3cDot11RRMAdjChlIntfTrapThhd	1.3.6.1.4.1.25506.2.75.8.1.5.1.5	Integer32	read-write	Represents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
hh3cDot11RRMAPCfg2Entry	1.3.6.1.4.1.25506.2.75.8.1.5.1		not-accessible	Each entry contains information of RRM parameters for AP.
hh3cDot11RRMAPCfg2Table	1.3.6.1.4.1.25506.2.75.8.1.5		not-accessible	This table defines the RRM parameters for AP.
hh3cDot11RRMAPCfgEntry	1.3.6.1.4.1.25506.2.75.8.1.3.1		not-accessible	Each entry contains information of RRM parameters for AP.
hh3cDot11RRMAPCfgTable	1.3.6.1.4.1.25506.2.75.8.1.3		not-accessible	This table defines the RRM parameters for AP.
I32 hh3cDot11RRMAPIntfThreshold	1.3.6.1.4.1.25506.2.75.8.1.5.1.2	Integer32	read-write	Represents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent.
HH3 hh3cDot11RRMAPSerialID	1.3.6.1.4.1.25506.2.75.8.1.5.1.1	Hh3cDot11ObjectIDType	not-accessible	Serial ID of the AP.
INT hh3cDot11RRMAPWorkMode	1.3.6.1.4.1.25506.2.75.8.1.3.1.1	INTEGER	read-write	AP work mode.
T/F hh3cDot11RRMAutoChlAvoid11h	1.3.6.1.4.1.25506.2.75.8.1.1.6	TruthValue	read-write	Configure the auto-channel set as non-dot11h channels, this is, only the non-dot11h channels belonging to the country code are scanned during initial channel selection and one of them is selected.
I32 hh3cDot11RRMCfgAdjacencyFctr	1.3.6.1.4.1.25506.2.75.8.1.2.1.13	Integer32	read-write	Configure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value n is the adjacency factor.
INT hh3cDot11RRMCfgChlMode	1.3.6.1.4.1.25506.2.75.8.1.2.1.3	INTEGER	read-write	Configure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled.
T/F hh3cDot11RRMCfgChlState	1.3.6.1.4.1.25506.2.75.8.1.2.1.2	TruthValue	read-write	Enable/Disable dynamic channel selection.
I32 hh3cDot11RRMCfgIntrfThres	1.3.6.1.4.1.25506.2.75.8.1.2.1.9	Integer32	read-write	Configure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel reaches the set threshold, RRM will perform resource adjustment to control the situation.
I32 hh3cDot11RRMCfgIntrvl	1.3.6.1.4.1.25506.2.75.8.1.2.1.8	Integer32	read-write	Configure the calibration interval.
I32 hh3cDot11RRMCfgNoiseThres	1.3.6.1.4.1.25506.2.75.8.1.2.1.10	Integer32	read-write	Configure the noise threshold.
I32 hh3cDot11RRMCfgPERThres	1.3.6.1.4.1.25506.2.75.8.1.2.1.11	Integer32	read-write	Configure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation.
INT hh3cDot11RRMCfgPwrMode	1.3.6.1.4.1.25506.2.75.8.1.2.1.6	INTEGER	read-write	Configure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled.
T/F hh3cDot11RRMCfgPwrState	1.3.6.1.4.1.25506.2.75.8.1.2.1.5	TruthValue	read-write	Enable/Disable dynamic power selection for the band.
I32 hh3cDot11RRMCfgToleranceFctr	1.3.6.1.4.1.25506.2.75.8.1.2.1.12	Integer32	read-write	Configure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interference and packet error rate than those specified by the user.
U32 hh3cDot11RRMChlProntoRadioElmt	1.3.6.1.4.1.25506.2.75.8.1.2.1.4	Unsigned32	read-write	Specify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of channel selection control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.
hh3cDot11RRMChlQltyNotifications	1.3.6.1.4.1.25506.2.75.8.3.1
hh3cDot11RRMChlQltyNtfPrefix	1.3.6.1.4.1.25506.2.75.8.3.1.0
I32 hh3cDot11RRMChlRptChlNum	1.3.6.1.4.1.25506.2.75.8.2.1.1.2	Integer32	accessible-for-notify	Channel number.
INT hh3cDot11RRMChlRptChlQlty	1.3.6.1.4.1.25506.2.75.8.2.1.1.4	INTEGER	read-only	Channel quality.
INT hh3cDot11RRMChlRptChlType	1.3.6.1.4.1.25506.2.75.8.2.1.1.3	INTEGER	read-only	Channel type.
hh3cDot11RRMChlRptEntry	1.3.6.1.4.1.25506.2.75.8.2.1.1		not-accessible	Each entry contains information of RRM channel information of the radio on the AP.
I32 hh3cDot11RRMChlRptIntrf	1.3.6.1.4.1.25506.2.75.8.2.1.1.8	Integer32	read-only	Interference observed on the channel in percentage.
I32 hh3cDot11RRMChlRptLoad	1.3.6.1.4.1.25506.2.75.8.2.1.1.6	Integer32	read-only	Load observed on the channel in percentage.
I32 hh3cDot11RRMChlRptNbrCnt	1.3.6.1.4.1.25506.2.75.8.2.1.1.5	Integer32	read-only	Number of neighbors found on the channel.
I32 hh3cDot11RRMChlRptNoise	1.3.6.1.4.1.25506.2.75.8.2.1.1.11	Integer32	read-only	Noise observed on the channel.
I32 hh3cDot11RRMChlRptPER	1.3.6.1.4.1.25506.2.75.8.2.1.1.9	Integer32	read-only	Packet error rate observed on the channel in percentage.
INT hh3cDot11RRMChlRptRadarIndtcr	1.3.6.1.4.1.25506.2.75.8.2.1.1.12	INTEGER	read-write	Radar detection status.
I32 hh3cDot11RRMChlRptRetryRate	1.3.6.1.4.1.25506.2.75.8.2.1.1.10	Integer32	read-only	Percentage of retransmission happened on the channel.
hh3cDot11RRMChlRptTable	1.3.6.1.4.1.25506.2.75.8.2.1		not-accessible	This table shows the RRM channel information of each radio on all APs.
I32 hh3cDot11RRMChlRptUtlz	1.3.6.1.4.1.25506.2.75.8.2.1.1.7	Integer32	read-only	Utilization of the channel in percentage.
I32 hh3cDot11RRMCoChlIntfTrapThhd	1.3.6.1.4.1.25506.2.75.8.1.5.1.4	Integer32	read-write	Represents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
hh3cDot11RRMConfigGroup	1.3.6.1.4.1.25506.2.75.8.1
hh3cDot11RRMDetectGroup	1.3.6.1.4.1.25506.2.75.8.2
hh3cDot11RRMGlobalCfgPara	1.3.6.1.4.1.25506.2.75.8.1.1
DAT hh3cDot11RRMHistoryChgDateTime	1.3.6.1.4.1.25506.2.75.8.2.3.1.12	DateAndTime	read-only	The time when the channel or power change occurred.
BIT hh3cDot11RRMHistoryChgReason	1.3.6.1.4.1.25506.2.75.8.2.3.1.11	Bits	read-only	Reason for the change of channel or power. The various bit positions are: \|0 \|Others \| \|1 \|Coverage \| \|2 \|Radar \| \|3 \|Retransmission \| \|4 \|Packets discarded \| \|5 \|Interference \| 0 is returned when the history record type is after.
HH3 hh3cDot11RRMHistoryChl	1.3.6.1.4.1.25506.2.75.8.2.3.1.3	Hh3cDot11ChannelScopeType	read-only	Channel on which the radio operates before/after the change of channel or power.
hh3cDot11RRMHistoryEntry	1.3.6.1.4.1.25506.2.75.8.2.3.1		not-accessible	Each entry shows the details of channel and power changes.
I32 hh3cDot11RRMHistoryId	1.3.6.1.4.1.25506.2.75.8.2.3.1.1	Integer32	not-accessible	History number of the change.
I32 hh3cDot11RRMHistoryIntrf	1.3.6.1.4.1.25506.2.75.8.2.3.1.7	Integer32	read-only	Interference observed on the radio in percentage before/after the change of channel or power.
I32 hh3cDot11RRMHistoryLoad	1.3.6.1.4.1.25506.2.75.8.2.3.1.5	Integer32	read-only	Load observed on the radio in percentage before/after the change of channel or power.
I32 hh3cDot11RRMHistoryNoise	1.3.6.1.4.1.25506.2.75.8.2.3.1.8	Integer32	read-only	Noise observed on the radio before/after the change of channel or power.
I32 hh3cDot11RRMHistoryPER	1.3.6.1.4.1.25506.2.75.8.2.3.1.9	Integer32	read-only	Packet error rate observed on the radio in percentage before/after the change of channel or power.
I32 hh3cDot11RRMHistoryPwr	1.3.6.1.4.1.25506.2.75.8.2.3.1.4	Integer32	read-only	Power of the radio before/after the change of channel or power.
INT hh3cDot11RRMHistoryRecIndctr	1.3.6.1.4.1.25506.2.75.8.2.3.1.2	INTEGER	not-accessible	History record type of the change.
I32 hh3cDot11RRMHistoryRetryRate	1.3.6.1.4.1.25506.2.75.8.2.3.1.10	Integer32	read-only	Percentage of retransmission happened on the radio before/after the change of channel or power.
hh3cDot11RRMHistoryTable	1.3.6.1.4.1.25506.2.75.8.2.3		not-accessible	This table shows the details of the latest three channel changes and power changes applied on all APs, including time of change, reason of the change and the channel, power, interference parameters.
I32 hh3cDot11RRMHistoryUtlz	1.3.6.1.4.1.25506.2.75.8.2.3.1.6	Integer32	read-only	Utilization of the radio in percentage before/after the change of channel or power.
NTF hh3cDot11RRMIntrfLimit	1.3.6.1.4.1.25506.2.75.8.3.1.0.1			This notification will be sent when interference on the radio exceeds the limit.
MAC hh3cDot11RrmNbrBSSID	1.3.6.1.4.1.25506.2.75.8.2.2.1.1	MacAddress	not-accessible	MAC address of the AP.
HH3 hh3cDot11RrmNbrChl	1.3.6.1.4.1.25506.2.75.8.2.2.1.2	Hh3cDot11ChannelScopeType	read-only	Channel number on which the neighbor was found.
hh3cDot11RRMNbrInfoEntry	1.3.6.1.4.1.25506.2.75.8.2.2.1		not-accessible	Each entry contains information of RRM neighbor information of the radio on an AP.
hh3cDot11RRMNbrInfoTable	1.3.6.1.4.1.25506.2.75.8.2.2		not-accessible	This table shows the RRM neighbor information of each radio on all APs.
I32 hh3cDot11RRMNbrIntrf	1.3.6.1.4.1.25506.2.75.8.2.2.1.3	Integer32	read-only	Interference observed on the channel in percentage by neighbor.
I32 hh3cDot11RrmNbrRSSI	1.3.6.1.4.1.25506.2.75.8.2.2.1.4	Integer32	read-only	Signal strength of the AP in dBm.
STR hh3cDot11RrmNbrSSID	1.3.6.1.4.1.25506.2.75.8.2.2.1.6	Hh3cDot11SSIDStringType	read-only	SSID of the Neighbor.
INT hh3cDot11RrmNbrType	1.3.6.1.4.1.25506.2.75.8.2.2.1.5	INTEGER	read-only	Type of the AP, managed or unmanaged.
NTF hh3cDot11RRMNoiseLimit	1.3.6.1.4.1.25506.2.75.8.3.1.0.3			This notification will be sent when noise on the radio exceeds the limit.
hh3cDot11RRMNotificationsVar	1.3.6.1.4.1.25506.2.75.8.3.3
hh3cDot11RRMNotifyGroup	1.3.6.1.4.1.25506.2.75.8.3
NTF hh3cDot11RRMPERLimit	1.3.6.1.4.1.25506.2.75.8.3.1.0.2			This notification will be sent when packet error rate on the radio exceeds the limit.
NTF hh3cDot11RRMPowerChange	1.3.6.1.4.1.25506.2.75.8.3.2.0.1			This notification will be sent when power changed on the radio automatically.
U32 hh3cDot11RRMPwrProntoRadioElmt	1.3.6.1.4.1.25506.2.75.8.1.2.1.7	Unsigned32	read-write	Specify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of transmit power control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.
hh3cDot11RRMRadioCfgEntry	1.3.6.1.4.1.25506.2.75.8.1.2.1		not-accessible	Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time.
hh3cDot11RRMRadioCfgTable	1.3.6.1.4.1.25506.2.75.8.1.2		not-accessible	Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time.
HH3 hh3cDot11RRMRadioIndex	1.3.6.1.4.1.25506.2.75.8.2.1.1.1	Hh3cDot11RadioElementIndex	accessible-for-notify	Represents index of the radio.
HH3 hh3cDot11RRMRadioType	1.3.6.1.4.1.25506.2.75.8.1.2.1.1	Hh3cDot11RadioType	not-accessible	802.11 radio type.
hh3cDot11RRMResChgNotifications	1.3.6.1.4.1.25506.2.75.8.3.2
hh3cDot11RRMResChgNtfPrefix	1.3.6.1.4.1.25506.2.75.8.3.2.0
INT hh3cDot11RRMScanChl	1.3.6.1.4.1.25506.2.75.8.1.1.7	INTEGER	read-write	Set the scan mode. auto: When this option is set, all channels of the country code being set are scanned. all: When this option is set, all the channels of the radio band are scanned.
I32 hh3cDot11RRMScanRptIntvel	1.3.6.1.4.1.25506.2.75.8.1.1.8	Integer32	read-write	Set the scan report interval.
OCT hh3cDot11RRMSDRadioGroupDesc	1.3.6.1.4.1.25506.2.75.8.1.4.1.2	OCTET STRING	read-create	Represents the description of RRM self-decisive radio group.
hh3cDot11RRMSDRadioGroupEntry	1.3.6.1.4.1.25506.2.75.8.1.4.1		not-accessible	Each entry contains information of one RRM self-decisive radio group.
U32 hh3cDot11RRMSDRadioGroupId	1.3.6.1.4.1.25506.2.75.8.1.4.1.1	Unsigned32	not-accessible	Represents RRM self-decisive radio group ID.
hh3cDot11RRMSDRadioGroupTable	1.3.6.1.4.1.25506.2.75.8.1.4		not-accessible	This table defines RRM self-decisive radio group.
ROW hh3cDot11RRMSDRdGroupRowStatus	1.3.6.1.4.1.25506.2.75.8.1.4.1.5	RowStatus	read-create	The row status of this table entry.
U32 hh3cDot11RRMSDRdGrpChlHolddownTm	1.3.6.1.4.1.25506.2.75.8.1.4.1.3	Unsigned32	read-create	Represents the channel holddown time of RRM self-decisive radio group.
U32 hh3cDot11RRMSDRdGrpPwrHolddownTm	1.3.6.1.4.1.25506.2.75.8.1.4.1.4	Unsigned32	read-create	Represents the power holddown time of RRM self-decisive radio group.
I32 hh3cDot11RRMStaIntfThreshold	1.3.6.1.4.1.25506.2.75.8.1.5.1.3	Integer32	read-write	Represents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent.
I32 hh3cDot11StaInterfNumThreshhd	1.3.6.1.4.1.25506.2.75.8.1.1.10	Integer32	read-write	Represents threshold of STA interference. If the value of STA interference exceeds this threshold, STA interference trap will be sent. If the value of this node is zero, STA interference trap will be sent immediately.

RFC description

H3C WLAN radio resource management MIB for 802.11 access point configuration and monitoring with RRM parameters and interference detection.

Start monitoring H3C wireless LAN controller/access point (Radio Resource Management) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HH3C-DOT11-RRM-MIB

What Is HH3C-DOT11-RRM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description