| OID symbolic | OID numeric | Type | Access | Description |
|---|
| org | 1.3 | | | |
| dod | 1.3.6 | | | |
| internet | 1.3.6.1 | | | |
| private | 1.3.6.1.4 | | | |
| enterprises | 1.3.6.1.4.1 | | | |
| bintec | 1.3.6.1.4.1.272 | | | |
| bibo | 1.3.6.1.4.1.272.4 | | | |
| tokenring | 1.3.6.1.4.1.272.4.11 | | | |
| tokenringIfTable | 1.3.6.1.4.1.272.4.11.1 | | not-accessible | The tokenringIfTable contains information relating to the
interfaces found on the system. Each entry corresponds to
a connected TokenRing interface. Entries can only be added or
deleted by the system.
Creating entries: Entries are created by the system
only when a new TokenRing module is installed.
Deleting entries: Entries are removed by the system
after the appropriate TokenRing module is removed. |
| tokenringIfEntry | 1.3.6.1.4.1.272.4.11.1.1 | | not-accessible | |
| INT tokenringIfSlot | 1.3.6.1.4.1.272.4.11.1.1.1 | INTEGER | read-only | Unique Slot of the TokenRing interface. |
| INT tokenringIfState | 1.3.6.1.4.1.272.4.11.1.1.2 | INTEGER | read-only | The TokenRing adapter initialization state |
| INT tokenringIfRingRate | 1.3.6.1.4.1.272.4.11.1.1.3 | INTEGER | read-write | speed of the token ring. |
| INT tokenringIfEarlyTokenRelease | 1.3.6.1.4.1.272.4.11.1.1.4 | INTEGER | read-write | enable or disable early token release. This feature is only
valid with the 16 Mbps ring rate |
| INT tokenringIfWrapInterface | 1.3.6.1.4.1.272.4.11.1.1.5 | INTEGER | read-write | enable or disable the wrap interface option. If enabled the
ring insertion process is omitted and all user-transmit data
appears as receive data. |
| INT tokenringIfMtu | 1.3.6.1.4.1.272.4.11.1.1.6 | INTEGER | read-write | The size of the largest datagram which can be
sent/received on the interface, specified in
octets. |
| PHY tokenringIfOverwritePhysAddress | 1.3.6.1.4.1.272.4.11.1.1.7 | PhysAddress | read-write | The interface's address at the protocol layer
immediately `below' the network layer in the
protocol stack. This overwrites the address
defined in the adapter PROM. |
| PHY tokenringIfNAUN | 1.3.6.1.4.1.272.4.11.1.1.8 | PhysAddress | read-only | The interface's address of the nearest upstream
neighbour. |
| CTR tokenringIfLineError | 1.3.6.1.4.1.272.4.11.1.1.9 | Counter | read-only | Count of line errors. This counter is incremented whenever
1) a frame is repeated or copied, and
2) the Error Detected Indicator (EDI) is zero in the incoming
frame, and
3) at least one of the following conditions exists:
a) a code violation between SDEL and EDEL
b) a code violation in a token
c) a FCS error |
| CTR tokenringIfBurstError | 1.3.6.1.4.1.272.4.11.1.1.10 | Counter | read-only | Count of burst errors. This counter is incremented whenever
the interface detects the absence of transitions for five
half-bit times between SDEL and EDEL, or EDEL and SDEL |
| CTR tokenringIfAriFciError | 1.3.6.1.4.1.272.4.11.1.1.11 | Counter | read-only | Count of ARI/FCI errors. This counter is incremented whenever
the interface receives an Active Monitor Present (AMP) MAC
frame with the ARI/FCI bit equal to zero and a Standby Monitor
Present (SMP) MAC frame with the ARI/FCI bits equal to zero,
or more than one SMP MAC frame with the ARI/FCI bits equal
to zero, without receiving an intervening AMP MAC frame. |
| CTR tokenringIfLostFrameError | 1.3.6.1.4.1.272.4.11.1.1.12 | Counter | read-only | Count of lost frames errors. This counter is incremented
whenever the interface is in transmit (stripping) mode and
fails to receive the end of the frame it transmitted |
| CTR tokenringIfReceiveCongestionError | 1.3.6.1.4.1.272.4.11.1.1.13 | Counter | read-only | Count of receive congestion errors. This counter is
incremented whenever the interface in the repeat mode
recognizes a frame addressed to it but has no buffer space
to copy the frame |
| CTR tokenringIfFrameCopiedError | 1.3.6.1.4.1.272.4.11.1.1.14 | Counter | read-only | Count of frame copied errors. This counter is incremented
whenever the interface in the receive/repeat mode recognizes
a frame addressed to its specific address but finds the
ARI bits not equal to zero |
| CTR tokenringIfTokenError | 1.3.6.1.4.1.272.4.11.1.1.15 | Counter | read-only | Count of token errors. This counter is only active in the
active monitor station. It is incremented when the active
monitor detects an error in the token protocol |
| CTR tokenringIfDmaBusError | 1.3.6.1.4.1.272.4.11.1.1.16 | Counter | read-only | Count of DMA bus errors. This counter is counts the occurences
of DMA bus errors that do not exceed the specified abort
thresholds |
| CTR tokenringIfDmaParityError | 1.3.6.1.4.1.272.4.11.1.1.17 | Counter | read-only | Count of DMA parity errors. This counter counts the occurences
of DMA parity errors that do not exceed the specified abort
thresholds |
| CTR tokenringIfSoftError | 1.3.6.1.4.1.272.4.11.1.1.18 | Counter | read-only | Count of soft errors that occur during normal operation. A soft
error is an error condition that temporarily degrades system
performance; however the ring recovers by using the protocols
of the adapter. The adapter counts these errors and can report
them to both the attached product and the ring error monitor. |
| INT tokenringIfSourceRouting | 1.3.6.1.4.1.272.4.11.1.1.19 | INTEGER | read-write | enable or disable source routing. If enabled, a routing
information field is added to the frame sent over this
interface. |
