| OID symbolic | OID numeric | Type | Access | Description |
|---|
| dnxE3 | 1.3.6.1.4.1.644.2.4.2.8 | | | |
| dnxE3Enterprise | 1.3.6.1.4.1.644.2.4.2.8.0 | | | ERI DNX E3 Enterprise for Alarms/Events |
| NTF e3PortConfigTrap | 1.3.6.1.4.1.644.2.4.2.8.0.1 | | | This trap is used to notify a NMS that a user has updated
the configuration for a given E3 Port entry. |
| NTF e3E1ConfigTrap | 1.3.6.1.4.1.644.2.4.2.8.0.2 | | | This trap is used to notify a NMS that a user has updated
the Link configuration for a given E3-E1 channel entry. |
| e3Config | 1.3.6.1.4.1.644.2.4.2.8.1 | | | |
| e3PortConfigTable | 1.3.6.1.4.1.644.2.4.2.8.1.1 | | not-accessible | This is the E3 Port Configuration table which consists
of an entry for each of the E3 cards. The total number of
entries depends on the number of E3 cards in the Node. |
| e3PortConfigEntry | 1.3.6.1.4.1.644.2.4.2.8.1.1.1 | | not-accessible | The conceptual row of the E3 Port Configuration table.
A row in this table cannot be added or deleted, only modified. |
| ADR e3PortCfgAddr | 1.3.6.1.4.1.644.2.4.2.8.1.1.1.1 | LinkPortAddress | read-only | This number uniquely identifies a E3 port resource.
This number will be used throughout the system to identify
a unique resource. |
| I32 e3PortCfgResource | 1.3.6.1.4.1.644.2.4.2.8.1.1.1.2 | Integer32 | read-only | Uniquely identifies an E3 Port in the system.
This number is provided as key to allow the manager to
map this entry to a corresponding Resource Table entry. |
| INT e3Timing | 1.3.6.1.4.1.644.2.4.2.8.1.1.1.3 | INTEGER | read-write | Determines the mode of E3 transmit timing provided by the
receive clock. When internal, timing is provided by an on-board
oscillator. |
| DEC e3ShortCable | 1.3.6.1.4.1.644.2.4.2.8.1.1.1.4 | DecisionType | read-write | Indicates the line build out of the E3 transmitter. 'Yes' when
attached to a cable less than 50 feet long. |
| LIN e3CmdStatus | 1.3.6.1.4.1.644.2.4.2.8.1.1.1.5 | LinkCmdStatus | read-write | The command status for this link configuration row/record.
The value used in a SET will be replaced by a response
value in the GET RESPONSE indicating success or failure.
Default Response State used in GET RESPONSE Command
ready-for-command (0)
initial default status for a row
E3 Link Commands used in SET Command (1..199)
update-link-config(1),
Change existing Link Configuration
Response States used in GET RESPONSE Command (200..399)
update-successful (201)
Link data has been successfully changed
E3 Port Config Error Codes used in GET RESPONSE Command (400..699)
err-general-link-config-error (400)
Unknown link configuration error occurred
err-invalid-link-command (403)
Unrecognized link command-action
err-invalid-link-rem-loop (408)
Remote Loop type not valid for e3 frame type
err-invalid-link-ais (409)
Unrecognized e3 AIS selection
err-device-in-standby (414)
Can't change config for designated Standby device
err-data-locked-by-another-user (450)
Another administrative user is making changes to this
part of the system via a terminal session. Check Event
Log for user name.
err-snmp-parse-failed (500)
Agent could not parse variable
err-invalid-snmp-type (501)
Variable ASN type does not match Agent defined type
err-invalid-snmp-var-size (502)
Variable size is too big |
| e3E1LinkConfigTable | 1.3.6.1.4.1.644.2.4.2.8.1.2 | | not-accessible | This is the E3 E1 Link Configuration table which consists
of an entry for each of the card's 16 links. The total number of
entries depends on the number of E3 cards in the Node. |
| e3E1LinkConfigEntry | 1.3.6.1.4.1.644.2.4.2.8.1.2.1 | | not-accessible | The conceptual row of the E3 E1 Link Configuration table.
A row in this table cannot be added or deleted, only modified. |
| ADR e3E1CfgLinkAddr | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.1 | LinkPortAddress | read-only | This number uniquely identifies a E3 E1 link resource.
This number will be used throughout the system to identify
a unique resource. |
| I32 e3E1CfgResource | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.2 | Integer32 | read-only | Uniquely identifies an E3 E1 Channel in the system.
This number is provided as key to allow the manager to
map this entry to a corresponding Resource Table entry. |
| STR e3E1CfgLinkName | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.3 | DisplayString | read-write | This is the user friendly text name to identify the link. |
| POR e3E1Status | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.4 | PortStatus | read-write | Dictates the current status of the link, in-service or
out-of-service. |
| INT e3E1Clear | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.5 | INTEGER | read-write | Determines if the port supports E1 unframed clear mode. |
| INT e3E1Framing | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.6 | INTEGER | read-write | Determines the type of framing used on the line.
When value of e3E1Clear is set to unframed (2), the only
valid framing option is: e1Unframed(4). |
| FUN e3E1NetLoop | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.7 | FunctionSwitch | read-write | Determines whether or not the module should respond to loop
diagnostic commands received from the network supplier. Select
'enable' unless the commands are to be passed to another E3
device. |
| DEC e3E1RAI | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.8 | DecisionType | read-write | Causes the module to discard data and send a yellow alarm if it
is in a red alarm condition after a 3 second period. 'Yes' must
be chosen if the network supplier is a common carrier, such as a
telephone company. |
| INT e3E1UnusedTSs | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.9 | INTEGER | read-write | Determines the whether the code that will be transmitted over
the unused links will be 'idle' or 'busy' (all 1's). |
| ONE e3E1NationalBits | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.10 | OneByteField | read-write | Enables E1 National S-bits to be set to zero or one.
This single byte field can be changed to set the values
of the E1 NFA byte in odd frames as depicted below:
sa8 sa7 sa6 sa5 sa4 reserved bits
--- --- --- --- --- -------------
1 1 1 1 1 0 0 0 = F8 (default)
Values should be entered in Hex. If reserved bits are changed,
an error code (427) will be returned in the command status. |
| LIN e3E1CfgCmdStatus | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.11 | LinkCmdStatus | read-write | The command status for this link configuration row/record.
The value used in a SET will be replaced by a response
value in the GET RESPONSE indicating success or failure.
Default Response State used in GET RESPONSE Command
ready-for-command (0)
initial default status for a row
E3-E1 Link Commands used in SET Command (1..199)
update(1)
Change existing Link Configuration
inServiceAll (7)
Change Link Status to in-service for all 16 links.
copyToAll (9)
Copy E1 Link configuration to all other links
within the same device
outOfServiceAll (12)
Change Link Status to out-of-service for all 16 links.
Response States used in GET RESPONSE Command (100..199)
update-successful (101)
Link data has been successfully changed
insvc-successful (107)
All Links have been successfully placed In Service
copy-successful (109)
E1 Link data has been successfully copied to other links
oos-successful (112)
All Links have been successfully placed Out of Service
E3-E1 Link Config Error Codes used in GET RESPONSE Command (400..699)
err-general-link-config-error (400)
Unknown link configuration error occurred
err-invalid-link-status (401)
Unrecognized link status setting
err-invalid-link-framing (402)
Line framing type not valid for link type
err-invalid-link-command (403)
Unrecognized link command-action
err-invalid-network-loop (410)
Unrecognized network loop setting
err-invalid-yellow-alrm (411)
Unrecognized yellow alarm setting
err-invalid-idle-code (413)
Unrecognized idle code
err-device-in-standby (414)
Can't change config for designated Standby device
err-invalid-link-bits (427)
Reserved E1 bits must be left at zero.
err-data-locked-by-another-user (450)
Another administrative user is making changes to this
part of the system via a terminal session. Check Event
Log for user name
err-snmp-parse-failed (500)
Agent could not parse variable
err-invalid-snmp-type (501)
Variable ASN type does not match Agent defined type
err-invalid-snmp-var-size (502)
Variable size is too big |
| ONE e3E1InterNational | 1.3.6.1.4.1.644.2.4.2.8.1.2.1.12 | OneByteField | read-write | Enables InterNational S(i) Spare bit to be set to zero or one.
This single byte field can be changed to set the values
of the Bit 1 of TS0 G.704 frame as depicted below:
reserved bits S(i)
-------------------------- -----
0 0 0 0 0 0 0 1 = 01 (default)
Values should be entered in Hex. If reserved bits are changed,
an error code (427) will be returned in the command status. |
| e3Diag | 1.3.6.1.4.1.644.2.4.2.8.2 | | | |
| e3FramerStatusTable | 1.3.6.1.4.1.644.2.4.2.8.2.1 | | not-accessible | This is the E-3 Framer Status table which consists of a single
entry for each card's Framer Display. The total number of
entries depends on the number of E3 cards in the nest. |
| e3FramerStatusEntry | 1.3.6.1.4.1.644.2.4.2.8.2.1.1 | | not-accessible | The conceptual row of the Framer table.
A row in this table cannot be added or deleted, only modified. |
| ADR e3FramerStatusAddr | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.1 | LinkPortAddress | read-only | This number uniquely identifies an e3 Framer resource.
This number will be used throughout the system to identify
a unique resource. |
| I32 e3FramerStatusResource | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.2 | Integer32 | read-only | This number uniquely identifies an e3 Framer link resource.
This number is provided as key to allow the manager to map this
entry to a corresponding Resource Table Entry. |
| INT e3FramerStatusState | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.3 | INTEGER | read-only | Determines the current line condition status of the Framer.
ok (0) - No Alarm
ais (8) - Sending All Ones
lof (32) - Loss/Out of Frame
los (64) - Loss of Signal
errors (2147483647) - Multiple Errors displays raw bit field value |
| C32 e3FramerStatusErrSecs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.4 | Counter32 | read-only | This is the total number of errored seconds. |
| C32 e3FramerStatusOOFErrs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.5 | Counter32 | read-only | This is the number of seconds an Out Of Frame alignment error was declared. |
| C32 e3FramerStatusAISSecs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.6 | Counter32 | read-only | This is the number of seconds an Alarm Indication Signal was declared. |
| C32 e3FramerStatusFramingErrs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.7 | Counter32 | read-only | Indicates the number of Framing Errors. |
| INT e3FramerStatusLoop | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.8 | INTEGER | read-write | The Loop status for the Framer as well as the Line Interface Unit. |
| INT e3FramerStatusBertState | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.9 | INTEGER | read-write | Indicates the Bert State.
bertOff (50) - Turns the BERT off
framed-2047 - Framed 2047
framed-2-15th - Framed 2^15-1 Inverted |
| C32 e3FramerStatusBertSecs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.10 | Counter32 | read-only | Indicates the Bert Duration in Seconds. |
| C32 e3FramerStatusBertErrSecs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.11 | Counter32 | read-only | Indicates the number of errored seconds since the Bert is running. |
| DAT e3FramerStatusBertSync | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.12 | DataSwitch | read-only | Indicates the Bert Synchronization as being ON or OFF. |
| C32 e3FramerStatusLiuRLOSs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.13 | Counter32 | read-only | This is the number of seconds recorded for Receive Loss of Signal. |
| C32 e3FramerStatusLiuRLOLs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.14 | Counter32 | read-only | This is the number of seconds recorded for Receive Loss of Lock. |
| C32 e3FramerStatusLiuLCVs | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.15 | Counter32 | read-only | This is the number of seconds recorded for the Line Code Violation. |
| INT e3FramerStatusInsErrMode | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.16 | INTEGER | read-write | Determines the status of the current Insert Error mode associated
with the framer. In order to insert an error, the e3FramerStatusCmdStatus
must be sent in a SET PDU with a value of 'insertError'. |
| INT e3FramerStatusCmdStatus | 1.3.6.1.4.1.644.2.4.2.8.2.1.1.17 | INTEGER | read-write | This is the command status for the Framer Row.
The value used in a SET will be replaced by a response
value in the GET RESPONSE indicating success or failure.
Default Response State used in GET RESPONSE Command
ready-for-command (0)
initial default status for a row
E3 Framer Action Commands used in SET Command (1..99)
update (1)
Can be used optionally when activating loops and berts
in order to get status code back in response
clearErrors (14)
Resets all error counters and bert test time to zero
insertError (16)
Inserts the current invalid bit pattern as indicated
by the value of e3FramerStatusCmdStatus.
Response States used in GET RESPONSE Command (100..199)
update-successful (101)
Test action has been successfully performed
clear-successful (114)
Error counts have been successfully cleared
insert-successful (116)
Errored bits have been successfully inserted
The Error Codes used in GET RESPONSE Command (200..799)
err-general-framer-error (200)
Unknown request error occurred.
err-invalid-loop-type (202)
Unrecognized loop selection
err-invalid-bert-type (203)
Unrecognized bert selection
err-test-in-progress (205)
Requested action cannot be performed during bert
err-field-cannot-be-set (206)
Read-only field was included in SET request
err-invalid-command (208)
Unrecognized framer Command requested
err-snmp-parse-failed (500)
Agent could not parse variable
err-invalid-snmp-type (501)
Variable ASN type does not match Agent defined type
err-invalid-snmp-var-size (502)
Variable size is too big |
| eriDNXE3MIB | 1.3.6.1.4.1.644.3.11 | | | The ERI Enterprise MIB Module for the DNX E3 Device. |
