DVB-CABLE-INA-IF-MIB

All MIBs › DVB-CABLE-INA-IF-MIB

Organization: DVB/DAVIC Interoperability Consortium Technical Working Group

Last Updated: 2001-02-09

Description: DVB/DAVIC MIB for EuroModem-compliant INA cable interface management on DVB-RC broadband cable access devices

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DVB-CABLE-INA-IF-MIB?

DVB-CABLE-INA-IF-MIB is a standard MIB from the DVB/DAVIC Interoperability Consortium Technical Working Group, defining interface objects for INAs (Interactive Network Adapters) conforming to the EuroModem specification (assumes MIB-II/RFC 1213 support). Its MAC table, keyed by interface, records device capabilities/extended capabilities, MAC capabilities/extended capabilities, protocol support, a set of numbered plus D/E/F contention timeouts, rapid-sign-on enable, response-collision time window, address-filter use/position-mask/comparison-value, grant-protocol timeout, idle interval/invalid count, and contention-message parameters (N, max length). As a configuration/protocol-status MIB it lets an administrator confirm a DVB cable INA's MAC-layer contention and addressing parameters conform to the EuroModem specification. It is deployed on DVB/DAVIC-compliant cable Interactive Network Adapters (EuroModem). Engineers implementing or auditing this functionality typically reference the DVB-CABLE-INA-IF-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in DVB-CABLE-INA-IF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

DVB/DAVIC-compliant cable Interactive Network Adapters (EuroModem)

Monitoring Examples

An administrator checks dvbInaIfMacProtocolSupport and dvbInaIfMacRapidSignOnEnable to confirm a cable INA's EuroModem MAC-layer configuration conforms to the DVB/DAVIC specification.

What Can Be Monitored

MAC-layer contention/addressing configuration

Imported Objects

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32
experimental
transmission

From SNMPv2-TC

MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using dvbInaIfMacUnknownNiuError OID:

Select a DVB/DAVIC EuroModem cable Interactive Network Adapter (vendor-neutral standard) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type dvbInaIfMacUnknownNiuError into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This value is incremented if a message is received from a unknown NIU, except if it is a SignOn_Response Message. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
dvbInaIf	1.3.6.1.2.1.10.146			The MIB modules for INAs that conform to the EuroModem specification. This MIB assumes the INA implements MIB-II RFC 1213 The original MIB definition work was carried out for the DVB-RC group by Bert Van Willigen Philips Research Laboratory Eindhoven, The Netherlands.
dvbInaIfMIBObjects	1.3.6.1.2.1.10.146.1
dvbInaIfMac	1.3.6.1.2.1.10.146.1.1
dvbInaIfMacTable	1.3.6.1.2.1.10.146.1.1.1		not-accessible	Describes the attributes of each MAC interface, extending the information available from ifEntry.
dvbInaIfMacEntry	1.3.6.1.2.1.10.146.1.1.1.1		not-accessible	An entry containing objects describing attributes of each MAC entry, extending the information in ifEntry. An entry in this table exists for each ifEntry with an ifType of dvbRecMacLayer(146). The state of the MAC depends on the state of the INA. If the INA is not operational also the MAC is not operational.
OCT dvbInaIfMacDeviceCapabilities	1.3.6.1.2.1.10.146.1.1.1.1.1	OCTET STRING	read-only	This 32-bit object specifies the maximum capabilities of this MAC entity. This is the possible set of capability for this INA.
OCT dvbInaIfMacDeviceExtendedCapabilities	1.3.6.1.2.1.10.146.1.1.1.1.2	OCTET STRING	read-only	This 32-bit object specifies the maximum extended capabilities of this MAC entity. This is the possible set of capability for this INA.
OCT dvbInaIfMacCapabilities	1.3.6.1.2.1.10.146.1.1.1.1.3	OCTET STRING	read-write	This 32-bit object specifies the capabilities of this MAC entity. It is equal to or a subset of dvbInaIfMacDeviceCapabilities. Default this parameter is equal to dvbInaIfMacDeviceCapabilities. The object can be used to restrict the capabilities for this MAC entity.
OCT dvbInaIfMacExtendedCapabilities	1.3.6.1.2.1.10.146.1.1.1.1.4	OCTET STRING	read-write	This 32-bit object specifies the extended capabilities of this MAC entity. It is equal to or a subset of dvbInaIfMacDeviceExtendedCapabilities. Default this parameter is equal to dvbInaIfMacDeviceExtendedCapabilities. The object can be used to restrict the extended capabilities for this MAC entity.
INT dvbInaIfMacProtocolSupport	1.3.6.1.2.1.10.146.1.1.1.1.5	INTEGER	read-write	Specifies the MAC standard version supported by this MAC entity. Optional, this parameter can be written to force a particular MAC version to be executed by the INA.
ETS dvbInaIfMacTimeout0	1.3.6.1.2.1.10.146.1.1.1.1.6	EtsTimeOut	read-write	Time-out value 0x0.
ETS dvbInaIfMacTimeout1	1.3.6.1.2.1.10.146.1.1.1.1.7	EtsTimeOut	read-write	Time-out value 0x1.
ETS dvbInaIfMacTimeout2	1.3.6.1.2.1.10.146.1.1.1.1.8	EtsTimeOut	read-write	Time-out value 0x2.
ETS dvbInaIfMacTimeout3	1.3.6.1.2.1.10.146.1.1.1.1.9	EtsTimeOut	read-write	Time-out value 0x3.
ETS dvbInaIfMacTimeout4	1.3.6.1.2.1.10.146.1.1.1.1.10	EtsTimeOut	read-write	Time-out value 0x4.
ETS dvbInaIfMacTimeoutD	1.3.6.1.2.1.10.146.1.1.1.1.11	EtsTimeOut	read-write	Time-out value 0xD. Terminal Time-Out, Security Sign-On.
ETS dvbInaIfMacTimeoutE	1.3.6.1.2.1.10.146.1.1.1.1.12	EtsTimeOut	read-write	Time-out value 0xE. Terminal Time-Out, Main Key Exchange.
ETS dvbInaIfMacTimeoutF	1.3.6.1.2.1.10.146.1.1.1.1.13	EtsTimeOut	read-write	Time-out value 0xF. Terminal Time-Out, Quick/Explicit Key exchange.
T/F dvbInaIfMacRapidSignOnEnable	1.3.6.1.2.1.10.146.1.1.1.1.14	TruthValue	read-write	This Boolean parameter specifies whether the NIU's are allowed to do a rapid sign-on when they enter the sign-on process. (See the Need_Calibration bit in the Sign-On_Request_Message.). By default this object is False.
U32 dvbInaIfMacRespCollTimeWindow	1.3.6.1.2.1.10.146.1.1.1.1.15	Unsigned32	read-write	Specifies the maximum time for the sign-on response message transmission randomisation.
INT dvbInaIfMacAddressFilterUse	1.3.6.1.2.1.10.146.1.1.1.1.16	INTEGER	read-write	This setting controls the use of the of the Address filter in the Sign-On Request Message. Disabled : The address filter is not used. Managed : The manager can control the use of the address filter with dvbInaIfMacAddressPositionMask and dvbInaIfMacAddressComparisonValue Automatic : The INA controls use of the address filter itself. The readback values of dvbInaIfMacAddressPositionMask and dvbInaIfMacAddressComparisonValue will not necessary reflect the values used by the INA.
INT dvbInaIfMacAddressPositionMask	1.3.6.1.2.1.10.146.1.1.1.1.17	INTEGER	read-write	Indicates the bit positions in the NIU MAC address that are used for address filtering comparison.
INT dvbInaIfMacAddressComparisonValue	1.3.6.1.2.1.10.146.1.1.1.1.18	INTEGER	read-write	Specifies the value that the NIU should use for MAC address comparison.
U32 dvbInaIfMacGrantProtocolTimeOut	1.3.6.1.2.1.10.146.1.1.1.1.19	Unsigned32	read-write	Default value for the time that the NIU should wait before verifying the status of pending grants. See also dvbInaIfNiuGrantProtocolTimeOut.
U32 dvbInaIfMacIdleInterval	1.3.6.1.2.1.10.146.1.1.1.1.20	Unsigned32	read-write	Specifies the transmission interval in seconds to be used for the MAC Idle message. When this value is zero, no idle messages shall be sent.
INT dvbInaIfMacIdleInvalidCount	1.3.6.1.2.1.10.146.1.1.1.1.21	INTEGER	read-write	Specifies a MAC Idle message invalid period in number of dvbInaIfMacIdleInterval, after which the NIU is declared to be signed-off. For example, if dvbInaIfMacIdleInterval is 5 seconds and this parameter is 3, then if in 15 seconds no data and/or MAC Idle messages are received, the INA will assume that the NIU in question has signed-off. This object is only valid when dvbInaIfMacIdleInterval is non-zero.
INT dvbInaIfMacN	1.3.6.1.2.1.10.146.1.1.1.1.22	INTEGER	read-write	Maximum value of the upstream slot position register.
INT dvbInaIfMacMaxContentionMsgLen	1.3.6.1.2.1.10.146.1.1.1.1.23	INTEGER	read-write	The default value for the Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using contention access. Any message greater than this should use reservation access. See also dvbInaIfConMaxContentionMsgLen.
INT dvbInaIfMacMaxReservationMsgLen	1.3.6.1.2.1.10.146.1.1.1.1.24	INTEGER	read-write	The default value for the Maximum_Reservation_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using a single reservation access. Any message greater than this should be transmitted by making multiple reservation requests. See also dvbInaIfConMaxReservationMsgLen.
G32 dvbInaIfMacNiuCount	1.3.6.1.2.1.10.146.1.1.1.1.25	Gauge32	read-only	Number of connected NIUs.
G32 dvbInaIfMacConnections	1.3.6.1.2.1.10.146.1.1.1.1.26	Gauge32	read-only	The number of connections currently active for this MAC entity.
C32 dvbInaIfMacUnknownNiuErrorEx	1.3.6.1.2.1.10.146.1.1.1.1.27	Counter32	read-only	This value is incremented if a message is received from a unknown NIU, except if it is a SignOn_Response Message.
C32 dvbInaIfMacMsgDataError	1.3.6.1.2.1.10.146.1.1.1.1.28	Counter32	read-only	This value is incremented if a MAC message is received with a data error, i.e. 1) is too short, 2) has an illegal Connection ID or Reservation ID, 3) is a reservation message from a NIU not reservation capable, 4) is a security message from a NIU not security capable 5) is an illegal MAC message.
C32 dvbInaIfMacMsgHdrError	1.3.6.1.2.1.10.146.1.1.1.1.29	Counter32	read-only	This value is incremented if a MAC message is received with a header error, i.e. 1) is too short, 2) does not contain a MAC address.
C32 dvbInaIfMacInvalidNiu	1.3.6.1.2.1.10.146.1.1.1.1.30	Counter32	read-only	This value is incremented if a MAC Initialisation Complete Message is transmitted with the Invalid_STB/NIU bit set.
C32 dvbInaIfMacTimingRangingError	1.3.6.1.2.1.10.146.1.1.1.1.31	Counter32	read-only	This value is incremented if a MAC Initialisation Complete Message is transmitted with the Timing_Ranging_Error bit set.
C32 dvbInaIfMacPowerRangingError	1.3.6.1.2.1.10.146.1.1.1.1.32	Counter32	read-only	This value is incremented if a MAC Initialisation Complete Message is transmitted with the Power_Ranging_Error bit set.
C32 dvbInaIfMacOtherSignOnError	1.3.6.1.2.1.10.146.1.1.1.1.33	Counter32	read-only	This value is incremented if a MAC Initialisation Complete Message is transmitted with the Other_Error bit set.
dvbInaIfProvision	1.3.6.1.2.1.10.146.1.2
dvbInaIfProvChTable	1.3.6.1.2.1.10.146.1.2.1		not-accessible	This table specifies the information for the Default Configuration Message transmitted on the Provisioning channel.
dvbInaIfProvChEntry	1.3.6.1.2.1.10.146.1.2.1.1		not-accessible	An entry containing objects describing information for the Default Configuration Message transmitted on the Provisioning channel. More than one downstream can use than same entry or different entries can be made for different downstreams. If provisioning is done on an other INA, this table will be empty.
INT dvbInaIfProvChIndex	1.3.6.1.2.1.10.146.1.2.1.1.1	INTEGER	not-accessible	Index of this table entry.
ROW dvbInaIfProvChRowAccessStatus	1.3.6.1.2.1.10.146.1.2.1.1.2	RowStatus	read-create	Controls and reflects the status of this row in this table.
NUM dvbInaIfProvChServiceChIfIndex	1.3.6.1.2.1.10.146.1.2.1.1.3	InterfaceIndex	read-create	The ifIndex of the upstream channel used as Service Channel for the provisioning.
NUM dvbInaIfProvChBackupServiceChIfIndex	1.3.6.1.2.1.10.146.1.2.1.1.4	InterfaceIndex	read-create	The ifIndex of the upstream channel used as Backup Service Channel for the provisioning.
INT dvbInaIfProvChIncrPowerRetryCount	1.3.6.1.2.1.10.146.1.2.1.1.5	INTEGER	read-create	Specifies the number of attempts the NIU should do to enter the system at the same power level before incrementing its upstream transmit power for this MAC entity.
INT dvbInaIfProvChMaxPowerLevel	1.3.6.1.2.1.10.146.1.2.1.1.6	INTEGER	read-create	Specifies the maximum power in dBuV the NIU is allowed to transmit upstream for this MAC entity.
INT dvbInaIfProvChMinPowerLevel	1.3.6.1.2.1.10.146.1.2.1.1.7	INTEGER	read-create	Specifies the minimum power in dBuV the NIU has to transmit upstream for this MAC entity.
INT dvbInaIfProvChMaxBackOffExponent	1.3.6.1.2.1.10.146.1.2.1.1.8	INTEGER	read-create	Specifies the maximum back off exponent counter for this MAC entity.
INT dvbInaIfProvChMinBackOffExponent	1.3.6.1.2.1.10.146.1.2.1.1.9	INTEGER	read-create	Specifies the minimum back off exponent counter for this MAC entity.
INT dvbInaIfProvChAbsoluteTimeOffset	1.3.6.1.2.1.10.146.1.2.1.1.10	INTEGER	read-create	Specifies the default absolute time offset in 100 ns units to be used for first sign-on of a NIU for this MAC entity.
dvbInaIfDsCh	1.3.6.1.2.1.10.146.1.3
dvbInaIfDsChTable	1.3.6.1.2.1.10.146.1.3.1		not-accessible	This table describes the attributes of downstream channels (frequency bands).
dvbInaIfDsChEntry	1.3.6.1.2.1.10.146.1.3.1.1		not-accessible	List of attributes for a single Downstream channel. An entry in this table exists for each downstream ifEntry.
DOW dvbInaIfDsChFrequency	1.3.6.1.2.1.10.146.1.3.1.1.1	DownFrequency	read-write	The centre of the downstream frequency associated with this channel.
G32 dvbInaIfDsChConnections	1.3.6.1.2.1.10.146.1.3.1.1.2	Gauge32	read-only	Specifies the number of connections currently active for this down stream channel.
INT dvbInaIfDsChTxPower	1.3.6.1.2.1.10.146.1.3.1.1.3	INTEGER	read-write	Specifies the down stream transmission power in dBuV of this interface.
U32 dvbInaIfDsChDownCoaxId	1.3.6.1.2.1.10.146.1.3.1.1.4	Unsigned32	read-write	Specifies the coax ID of the Downstream HFC segment to which the downstream channel is connected. By default this parameter is zero.
DOW dvbInaIfDsChSymbolRate	1.3.6.1.2.1.10.146.1.3.1.1.5	DownstreamSymbolrate	read-write	Specifies the symbol rate for the Downstream channel.
MOD dvbInaIfDsChModulation	1.3.6.1.2.1.10.146.1.3.1.1.6	Modulation	read-write	Specifies the modulation for the Downstream channel.
INT dvbInaIfDsChType	1.3.6.1.2.1.10.146.1.3.1.1.7	INTEGER	read-write	Specifies if the Downstream channel is inband or out-of-band.
U32 dvbInaIfDsChDefaultPID	1.3.6.1.2.1.10.146.1.3.1.1.8	Unsigned32	read-write	The default value of the MPEG PID of the elementary stream that carries the data on this downstream. See also dvbInaIfConPID.
DOW dvbInaIfDsChProvFrequency	1.3.6.1.2.1.10.146.1.3.1.1.9	DownFrequency	read-write	Specifies the Downstream frequency of the provisioning channel. This setting is always used, no matter the provisioning channel is on this INA or on another. If the provisioning channel is on this INA, the value will be the frequency of one of the downstreams.
INT dvbInaIfDsChProvDownstreamType	1.3.6.1.2.1.10.146.1.3.1.1.10	INTEGER	read-write	Specifies the type of the downstream provisioning channel in the Provisioning Channel Message. 0 = QAM_MPEG, 1 = QPSK_1,544, 2 = QPSK_3,088 3..255 Reserved This setting is always used, no matter the provisioning channel is on this INA or on another. If the provisioning channel is on this INA, the value can be derived from the ib/oob type and modulation.
T/F dvbInaIfDsChProvEnable	1.3.6.1.2.1.10.146.1.3.1.1.11	TruthValue	read-write	Specifies if this downstream channel is a Provisioning channel and as such transmits the Default Configuration Message. true = Provisioning channel false = not a Provisioning channel.
INT dvbInaIfDsChProvTableIndex	1.3.6.1.2.1.10.146.1.3.1.1.12	INTEGER	read-write	If this downstream channel is a provisioning channel, then an index to the Provisioning tabel must be give here.
dvbInaIfUsCh	1.3.6.1.2.1.10.146.1.4
dvbInaIfUsChTable	1.3.6.1.2.1.10.146.1.4.1		not-accessible	Describes the attributes of attached upstream channels (frequency bands).
dvbInaIfUsChEntry	1.3.6.1.2.1.10.146.1.4.1.1		not-accessible	List of attributes for a single upstream channel. The state of the upstream channel depends on the state of the MAC and downstream channel. If one of both or both are non-operational also the state upstream channel(s) shall be ready. That in the case of Space division Multiplex SDM each upstream channel has a different non-zero Coax ID.
UPF dvbInaIfUsChFrequency	1.3.6.1.2.1.10.146.1.4.1.1.1	UpFrequency	read-write	Specifies the frequency in Hz of the carrier used for this upstream channel.
UPS dvbInaIfUsChSymbolRate	1.3.6.1.2.1.10.146.1.4.1.1.2	UpstreamSymbolrate	read-write	Specifies the symbol rate for this upstream channel.
MOD dvbInaIfUsChModulation	1.3.6.1.2.1.10.146.1.4.1.1.3	Modulation	read-write	Specifies the modulation for this upstream channel.
MAC dvbInaIfUsChMacFlagSet	1.3.6.1.2.1.10.146.1.4.1.1.4	MacFlagSet	read-only	Specifies the MAC flag set assigned to this upstream channel.
INT dvbInaIfUsChId	1.3.6.1.2.1.10.146.1.4.1.1.5	INTEGER	read-only	Specifies the logical channel number associated with this upstream channel.
G32 dvbInaIfUsChConnections	1.3.6.1.2.1.10.146.1.4.1.1.6	Gauge32	read-only	Specifies the number of connections currently active for this upstream channel.
INT dvbInaIfUsChCalibrationRxPower	1.3.6.1.2.1.10.146.1.4.1.1.9	INTEGER	read-write	Specifies the target receive signal power in dBuV to which the NIUs on this upstream channel are calibrated
U32 dvbInaIfUsChUpCoaxId	1.3.6.1.2.1.10.146.1.4.1.1.10	Unsigned32	read-write	Specifies the coax ID of the UpStream HFC segment to which the upstream channel is connected. By default this parameter is zero.
U32 dvbInaIfUsChDownCoaxId	1.3.6.1.2.1.10.146.1.4.1.1.11	Unsigned32	read-write	Specifies the coax ID of the Downstream HFC segment to which the upstream channel is connected. By default this parameter is zero.
C64 dvbInaIfUsChAtmCells	1.3.6.1.2.1.10.146.1.4.1.1.12	Counter64	read-only	Total number of recieved ATM Cells. 0 can indicate the counter is not supported.
C64 dvbInaIfUsChAtmTimingErrors	1.3.6.1.2.1.10.146.1.4.1.1.13	Counter64	read-only	Number of ATM Cells received with Timing Error. 0 can indicate the counter is not supported.
C64 dvbInaIfUsChAtmPowerErrors	1.3.6.1.2.1.10.146.1.4.1.1.14	Counter64	read-only	Number of ATM Cells received with Signal Level Error. 0 can indicate the counter is not supported.
C64 dvbInaIfUsChAtmRSCorrectableErrors	1.3.6.1.2.1.10.146.1.4.1.1.15	Counter64	read-only	Number of ATM Cells received with correctable Reed-Solomon Errors. 0 can indicate the counter is not supported.
C64 dvbInaIfUsChAtmRSNonCorrectableErrors	1.3.6.1.2.1.10.146.1.4.1.1.16	Counter64	read-only	Number of ATM Cells received with non-correctable Reed-Solomon Errors. 0 can indicate the counter is not supported.
C64 dvbInaIfUsChAtmHecErrors	1.3.6.1.2.1.10.146.1.4.1.1.17	Counter64	read-only	Number of ATM Cells received with HEC Error. 0 can indicate the counter is not supported.
C64 dvbInaIfUsChAal5CrcErrors	1.3.6.1.2.1.10.146.1.4.1.1.18	Counter64	read-only	Number AAL5 frames received with CRC error. 0 can indicate the counter is not supported.
C64 dvbInaIfUsChAtmCollisionErrors	1.3.6.1.2.1.10.146.1.4.1.1.19	Counter64	read-only	Number of ATM Cells received with Collision detected. 0 can indicate the counter is not supported.
dvbInaIfNiu	1.3.6.1.2.1.10.146.1.5
dvbInaIfNiuTable	1.3.6.1.2.1.10.146.1.5.1		not-accessible	Describes the attributes of Network Interface Units.
dvbInaIfNiuEntry	1.3.6.1.2.1.10.146.1.5.1.1		not-accessible	Initially the table shall be empty. A new entry for a NIU is automatically created when the NIU in question signs on. Furthermore, the manager through the dvbInaIfNiuRowAccessStatus object can create new entries. This can be used in the case of re-provisioning where by the manager first makes an entry and sets all relevant parameters before the NIU is re-provisioned to this INA. When an entry is created for a NIU, also automatically an entry is created in the connection table for the default connection of the NIU in question. When a NIU entry is deleted, also all associated connection entries are deleted.
MAC dvbInaIfNiuMacAddress	1.3.6.1.2.1.10.146.1.5.1.1.1	MacAddress	not-accessible	A 48-bit value representing the unique MAC address of the NIU.
ROW dvbInaIfNiuRowAccessStatus	1.3.6.1.2.1.10.146.1.5.1.1.2	RowStatus	read-create	Controls and reflects the status of this row in this table.
INT dvbInaIfNiuState	1.3.6.1.2.1.10.146.1.5.1.1.3	INTEGER	read-only	Returned status information is the NIU status as assumed by the INA. The following states are possible: null(1) Any state other than below. ranging(2): The NIU has responded to a [MAC] Sign-on Request Message but the time ranging and power calibration is not yet complete. rangingAborted(3), The INA has sent a Initalisation Complete Message to the NIU with Completion_Status_Field != 0 rangingComplete(4), The INA has sent a Initalisation Complete Message to the NIU with Completion_Status_Field = 0 connecting(5), The INA has sent a Connect Message for first connection and is waiting for a Connect Response Message from the NIU. connectComplete(6) The INA has sent a Connect Confirm Message for first connection to the NIU. stopped(7) The NUI is in the stopped transmission state after the INA has send a Stop_Upstream_Transmission to the NIU and the NIU has returned a Link Management Response. NOTE: The INA only needs to report states it is able to detect.
INT dvbInaIfNiuDesiredState	1.3.6.1.2.1.10.146.1.5.1.1.4	INTEGER	read-create	Specifies the desired state of the NIU. This parameter can be set to one of the following values: down : Initial state. Disable NIU operation. start : Enable NIU operation. stop : Stop upstream transmission from the NIU.
NUM dvbInaIfNiuDownIfIndex	1.3.6.1.2.1.10.146.1.5.1.1.5	InterfaceIndexOrZero	read-only	Specifies the IfIndex of the downstream channel on which the NIU is tuned.
NUM dvbInaIfNiuUpIfIndex	1.3.6.1.2.1.10.146.1.5.1.1.6	InterfaceIndexOrZero	read-only	Specifies the IfIndex of the upstream channel that is used by the NIU.
INT dvbInaIfNiuUpTxLevel	1.3.6.1.2.1.10.146.1.5.1.1.7	INTEGER	read-only	Specifies the upstream transmit level. This is the INA notion of NIU transmit level. (See also 'dvbInaIfNiuRespTxLevel'.)
I32 dvbInaIfNiuTimeOffset	1.3.6.1.2.1.10.146.1.5.1.1.8	Integer32	read-only	Specifies the time offset. This is the INA notion of NIU time offset. (See also 'dvbInaIfNiuRespTimeOffset'.)
U32 dvbInaIfNiuStatus	1.3.6.1.2.1.10.146.1.5.1.1.9	Unsigned32	read-only	This 32-bit object specifies the status of this NIU. See Sign-On Response Message and Status Response Message [1] for the exact bit assignment. This object is updated after the reception of a Status Response Message [1].
U32 dvbInaIfNiuErrorCode	1.3.6.1.2.1.10.146.1.5.1.1.10	Unsigned32	read-only	This 16-bit object specifies the error code in the Sign-On Response Message. See ES 200 800 for the exact bit assignment.
INT dvbInaIfNiuRetryCount	1.3.6.1.2.1.10.146.1.5.1.1.11	INTEGER	read-only	This 8-bit object specifies the number of transmissions of the Sign-On Response Message. (See [1]).
OCT dvbInaIfNiuCapabilities	1.3.6.1.2.1.10.146.1.5.1.1.12	OCTET STRING	read-only	This 32-bit object specifies the capabilities of this NIU. See also ES 200 800 for the bit assignment.
OCT dvbInaIfNiuExtendedCapabilities	1.3.6.1.2.1.10.146.1.5.1.1.13	OCTET STRING	read-only	This 32-bit object specifies the extended capabilities of this NIU. See also ES 200 800 and ECR 5 for the bit assignment.
INT dvbInaIfNiuInitCompletionStatus	1.3.6.1.2.1.10.146.1.5.1.1.14	INTEGER	read-only	This 8-bit object indicates the errors in the initialisation phase of this NIU. See the Initialization Complete Message ES 200 800 for the exact bit assignment.
INT dvbInaIfNiuRequestStatus	1.3.6.1.2.1.10.146.1.5.1.1.15	INTEGER	read-create	This object triggers the transmission of a Status Request Message [1]. This parameter can be set to one of the following parameters: 'NiuReqAddressPars(0)': request address parameters, 'NiuReqErrorPars(1)': request error parameters, 'NiuReqConnectionsPars(2)': request connection parameters, and 'NiuReqPhyLayerPars(3)': request physical layer parameters. When read this object returns 'NiuReqAddressPars(0)'.
C32 dvbInaIfNiuResponseNumber	1.3.6.1.2.1.10.146.1.5.1.1.16	Counter32	read-only	This object is incremented when a Status Response Message [1] is received. This object can be polled to detect the reception of this message. After reset this object is zero.
INT dvbInaIfNiuRespTxLevel	1.3.6.1.2.1.10.146.1.5.1.1.17	INTEGER	read-only	Specifies the transmit power level of the NIU. This object is updated after the reception of a Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.
I32 dvbInaIfNiuRespTimeOffset	1.3.6.1.2.1.10.146.1.5.1.1.18	Integer32	read-only	Specifies the time offset of the NIU. This object is updated after the reception of a Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.
DOW dvbInaIfNiuRespOoBDownFrequency	1.3.6.1.2.1.10.146.1.5.1.1.19	DownFrequency	read-only	Specifies the OoB downstream frequency of the NIU. This object is updated after the reception of a Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.
DOW dvbInaIfNiuRespIBDownFrequency	1.3.6.1.2.1.10.146.1.5.1.1.20	DownFrequency	read-only	Specifies the IB downstream frequency of the NIU. This object is updated after the reception of a Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.
INT dvbInaIfNiuRespSNRLevel	1.3.6.1.2.1.10.146.1.5.1.1.21	INTEGER	read-only	Specifies the estimated SNR level at the RF input of the NIU. This object is updated after the reception of a Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.
INT dvbInaIfNiuRespRxLevel	1.3.6.1.2.1.10.146.1.5.1.1.22	INTEGER	read-only	Specifies the estimated downstream power level of the MAC messages at the RF input of the NIU. This object is updated after the reception of a Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.
U32 dvbInaIfNiuDefaultConnectionId	1.3.6.1.2.1.10.146.1.5.1.1.23	Unsigned32	read-create	Specifies the ConnectionId of the default connection that is assigned to this NIU.
U32 dvbInaIfNiuLifetime	1.3.6.1.2.1.10.146.1.5.1.1.24	Unsigned32	read-create	Defines how long after the NIU was signed off, the entry is removed from the table. An infinite(0) value would mean that the values are stored at least until the next reboot of the INA.
U32 dvbInaIfNiuGrantProtocolTimeOut	1.3.6.1.2.1.10.146.1.5.1.1.25	Unsigned32	read-create	The time that the NIU should wait before verifying the status of pending grants. Default value is dvbInaIfMacGrantProtocolTimeOut.
C32 dvbInaIfNiuSlotConfigurationErr	1.3.6.1.2.1.10.146.1.5.1.1.26	Counter32	read-only	NIU Error Parameter: Slot_Configuration_CRC_Error_Count, the number of errors in Slot_Configuration_Count R bytes, as found by the CRC decoder.
C32 dvbInaIfNiuAtmPacketLoss	1.3.6.1.2.1.10.146.1.5.1.1.27	Counter32	read-only	NIU Error Parameter: ATM_Packet_Loss_Count, the number of received ATM cells that were lost, either due to unrecoverable Reed-Solomon errors or because of an erroneous HEC of the ATM cell header.
C32 dvbInaIfNiuSlEsCrcErr	1.3.6.1.2.1.10.146.1.5.1.1.28	Counter32	read-only	Niu Error Parameter: SL-ESF_CRC_Error_Count, the number of CRC errors found in consecutive C1-C6.
C32 dvbInaIfNiuSlEsFrameCount	1.3.6.1.2.1.10.146.1.5.1.1.29	Counter32	read-only	NIU Error Parameter: SL-ESF_Frame_Count, the number of frames the statistics apply to.
C32 dvbInaIfNiuSlotConfigurationCount	1.3.6.1.2.1.10.146.1.5.1.1.30	Counter32	read-only	NIU Error Parameter: Slot_Configuration_Count, the number of R-byte sets (Rxa-Rxc) used to calculate Slot_Configuration_CRC_Error_Count.
C32 dvbInaIfNiuRSErrCorrectable	1.3.6.1.2.1.10.146.1.5.1.1.31	Counter32	read-only	NIU Error Parameter: Reed_Solomon_Errors_Correctable, MPEG frames received with correctable Reed-Solomon Errors (IB only).
C32 dvbInaIfNiuRSErrNonCorrectable	1.3.6.1.2.1.10.146.1.5.1.1.32	Counter32	read-only	NIU Error Parameter: Reed_Solomon_Errors_Non_Correctable, MPEG frames received with non-correctable Reed-Solomon Errors (IB only).
TIK dvbInaIfNiuSignOnTime	1.3.6.1.2.1.10.146.1.5.1.1.33	TimeTicks	read-only	The value of sysUpTime at the time this NIU was signed on. If the time is unknown, this value shall be zero.
C64 dvbInaIfNiuDsChBytes	1.3.6.1.2.1.10.146.1.5.1.1.34	Counter64	read-only	Number of bytes sent in direction INA to NIU.
C64 dvbInaIfNiuUsChBytes	1.3.6.1.2.1.10.146.1.5.1.1.35	Counter64	read-only	Number of bytes sent in direction NIU to INA. Includes backbone, NIU-to-NIU and broadcast/multicast traffic.
C32 dvbInaIfNiuTimeRanging	1.3.6.1.2.1.10.146.1.5.1.1.36	Counter32	read-only	Number of times the NIU has been time ranged.
C32 dvbInaIfNiuPowerRanging	1.3.6.1.2.1.10.146.1.5.1.1.37	Counter32	read-only	Number of times the NIU has been power ranged.
dvbInaIfConnection	1.3.6.1.2.1.10.146.1.6
dvbInaIfConTable	1.3.6.1.2.1.10.146.1.6.1		not-accessible	Contains information about DVB-RC MAC connections.
dvbInaIfConEntry	1.3.6.1.2.1.10.146.1.6.1.1		not-accessible	Initially the table shall be empty. A new entry for a connection is automatically generated when a Resource Request Message is received from the NIU in question requesting a new connection. Also during reprovisioning new entries are created. Furthermore, the manager through the dvbInaIfConAccessStatus object can create new entries. Connection table entries shall be deleted, when the associated NIU entry is deleted. Furthermore, the manager can delete unused connection entries. The following parameters can only be set when the connection is in state down(1) dvbInaIfConAccessStatus, dvbInaIfConEncapsulation, dvbInaIfConFilterMACAddress, dvbInaIfConPID.
MAC dvbInaIfConNiuMacAddress	1.3.6.1.2.1.10.146.1.6.1.1.1	MacAddress	not-accessible	MAC address of the NIU that is associated with the connection.
U32 dvbInaIfConConnectionId	1.3.6.1.2.1.10.146.1.6.1.1.2	Unsigned32	not-accessible	Specifies the connection identifier to be used for this connection.
INT dvbInaIfConCurrentState	1.3.6.1.2.1.10.146.1.6.1.1.3	INTEGER	read-only	Current state of the connection. The following states are possible: down(1) In this state an entry is made in the connection table for the connection in question. However, there is not (yet) any connection on MAC layer between the INA and NIU. settingUp(2) Either the NIU in question has requested a connection via a [MAC] Resource Request message, or the manager has initiated a (new) connection by setting dvbInaConDesiredState to the state Up. up(3) In this state the connection in question is up and running. breakingDown(4) Either the NIU in question has requested to release the connection via a [MAC] Resource Request message, or the manager has initiated the release of the connection by setting dvbInaConDesiredState to the state: Down. downAlloc(5) In this state an entry is made in the connection table for the connection in question. Furthermore, the bandwidth for the fixed rate connection is allocated. However, the connection doesn't (yet) exist on MAC layer between the INA and NIU. alarm(6) The connection in question is in the alarm state. his means that either the parameter setting is not valid, or the scheduler of the MAC has not the resources to allocate the requested bandwidth for a fixed rate connection, or the NIU didn't response in time during the set-up of the connection or during the break down of it. This state shall be left, when either the manager sets dvbInaConDesiredState to Down(1) or, the NIU enters the Null(1) state.
INT dvbInaIfConDesiredState	1.3.6.1.2.1.10.146.1.6.1.1.4	INTEGER	read-create	Desired state for the connection. The following desired states are possible: down(1), up(3) and, downAlloc(5).
BIT dvbInaIfConConnectionType	1.3.6.1.2.1.10.146.1.6.1.1.5	Bits	read-create	Specifies the kind of connection: fixed rate, contention based, or reservation based. This parameter can be set to a value that is an OR of the following bits: 'conTypeFixedRate(0)' 'conTypeContention(1)' 'conTypeReservation(2)' Default this object is 'conTypeContention(1)'.
ROW dvbInaIfConAccessStatus	1.3.6.1.2.1.10.146.1.6.1.1.6	RowStatus	read-create	Controls and reflects the status of this row in this table.
INT dvbInaIfConEncapsulation	1.3.6.1.2.1.10.146.1.6.1.1.7	INTEGER	read-create	This object indicates the type of encapsulation provided on this connection. This object can have one of the following values: 'directIp(1)', 'ethernetMacBridging(2)', or 'ppp(3)'. By default this parameter is set to 'directIp(1)'.
U32 dvbInaIfConAtmDownstreamVCC	1.3.6.1.2.1.10.146.1.6.1.1.8	Unsigned32	read-only	ATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission.
U32 dvbInaIfConAtmUpstreamVCC	1.3.6.1.2.1.10.146.1.6.1.1.9	Unsigned32	read-only	ATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission.
MAC dvbInaIfConFilterMACAddress	1.3.6.1.2.1.10.146.1.6.1.1.10	MacAddress	read-create	Specifies the 'soft' MPEG MPE MAC address used to filter the data out of the downstream IB transmission. This is found in the Downstream_Multiprotocol_CBD substructure in the Connect Message.
U32 dvbInaIfConPID	1.3.6.1.2.1.10.146.1.6.1.1.11	Unsigned32	read-create	Specifies the MPEG PID of the elementary stream that carries the data.
INT dvbInaIfConMaxContentionMsgLen	1.3.6.1.2.1.10.146.1.6.1.1.12	INTEGER	read-create	The Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using contention access. Any message greater than this should use reservation access. The default value should be dvbInaIfMacMaxContentionMsgLen.
INT dvbInaIfConMaxReservationMsgLen	1.3.6.1.2.1.10.146.1.6.1.1.13	INTEGER	read-create	This is the maximum length of a message that may be transmitted using a single reservation access. Any message greater than this should be transmitted by making multiple reservation requests. The default value should be dvbInaIfMacMaxReservationMsgLen.
INT dvbInaIfConAuxFlags	1.3.6.1.2.1.10.146.1.6.1.1.14	INTEGER	read-only	The Connection_Control_Field_Aux from the Connect Message Structure. This is used to indicate if the Priority, Downstream flowspec and Session binding objects are used for the connection.
dvbInaIfConQosTable	1.3.6.1.2.1.10.146.1.6.2		not-accessible	Contains information about connection quality for DVB-RC MAC connections. Both upstream and downstream quality parameters are found.
dvbInaIfConQosEntry	1.3.6.1.2.1.10.146.1.6.2.1		not-accessible	An entry in the table is automatically created when a new entry in the connection table connection is created and the INA supports Quality of Service on the MAC layer. You must always create an entry in the Connection table first and this will automatically create an entry in the QoS table. The entries are deleted when the contection table entry is deleted.
INT dvbInaIfConQosPriority	1.3.6.1.2.1.10.146.1.6.2.1.1	INTEGER	read-write	The priority of the connection. Connections with low priority field value can be reprovisioned in order to accommodate the requirements of connections with high priority field. Standard data flow applications 0-79 Applications with QoS requirements 80-200 High priority applications 201-255
U32 dvbInaIfConQosDsReqMaxPacketSize	1.3.6.1.2.1.10.146.1.6.2.1.2	Unsigned32	read-write	A downstream QoS parameter. Defines the requested maximum packet size in the downstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request. The packet size includes propriety protocols header, transport protocol (UDP/TCP) header, and the IP header. The packet size does not include the Ethernet header.
U32 dvbInaIfConQosDsReqBitrate	1.3.6.1.2.1.10.146.1.6.2.1.3	Unsigned32	read-write	A downstream QoS parameter. Defines requested average bit rate in the downstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.
INT dvbInaIfConQosDsReqJitter	1.3.6.1.2.1.10.146.1.6.2.1.4	INTEGER	read-write	A downstream QoS parameter. Defines the requested maximum allowed jitter in the downstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.
U32 dvbInaIfConQosDsAllocMaxPacketSize	1.3.6.1.2.1.10.146.1.6.2.1.5	Unsigned32	read-only	A downstream QoS parameter. This is the actual maximum packet size supported by the INA in the downstream. The packet size includes propriety protocols header, transport protocol (UDP/TCP) header, and the IP header. The packet size does not include the Ethernet header.
U32 dvbInaIfConQosDsAllocBitrate	1.3.6.1.2.1.10.146.1.6.2.1.6	Unsigned32	read-only	A downstream QoS parameter. This is the actual average bit rate supported by the INA in the downstream.
INT dvbInaIfConQosDsAllocJitter	1.3.6.1.2.1.10.146.1.6.2.1.7	INTEGER	read-only	A downstream QoS parameter. This is the actual maximum jitter supported by the INA in the downstream.
U32 dvbInaIfConQosUsReqBw	1.3.6.1.2.1.10.146.1.6.2.1.8	Unsigned32	read-write	An upstream QoS parameter. The requested bandwidth for the upstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.
U32 dvbInaIfConQosUsReqMaxDistSlots	1.3.6.1.2.1.10.146.1.6.2.1.9	Unsigned32	read-write	An upstream QoS parameter. The requested maximum distance between slots for the upstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.
U32 dvbInaIfConQosUsReqFrameLength	1.3.6.1.2.1.10.146.1.6.2.1.10	Unsigned32	read-write	An upstream QoS parameter. The requested frame length for the upstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.
U32 dvbInaIfConQosUsAllocBw	1.3.6.1.2.1.10.146.1.6.2.1.11	Unsigned32	read-only	An upstream QoS parameter. The actual allocated bandwidth for the upstream.
U32 dvbInaIfConQosUsAllocMaxDistSlots	1.3.6.1.2.1.10.146.1.6.2.1.12	Unsigned32	read-only	An upstream QoS parameter. The allocated distance between slots for the upstream. In case of using a cyclic assignment, this is the parameter sent by the INA in the connect message. In the case of reservation access, this parameter is an average number, calculated by the INA to reflect the actual allocation.
U32 dvbInaIfConQosUsAllocFrameLength	1.3.6.1.2.1.10.146.1.6.2.1.13	Unsigned32	read-only	An upstream QoS parameter. The allocated frame length for the upstream. In case of using a cyclic assignment, this is the parameter sent by the INA in the connect message. In the case of reservation access, this parameter is an average number, calculated by the INA to reflect the actual allocation.
INT dvbInaIfConQosUsReqFixedRateMethod	1.3.6.1.2.1.10.146.1.6.2.1.14	INTEGER	read-write	An upstream QoS parameter. Request a specific fixed rate slot assignment method to be used. If cyclic then cyclic assignment is used. If slotList then the slot list method is used. The parameter can be set either by the managment system, or by the INA according to the NIU resource request. If the bit Cyclic_Assignment_Needed is set, the NIU requests the cyclic method. Otherwise the slot list method.
INT dvbInaIfConQosUsAllocFixedRateMethod	1.3.6.1.2.1.10.146.1.6.2.1.15	INTEGER	read-only	An upstream QoS parameter. Reflects the actual fixed rate slot assignment method that is used. If cyclic then cyclic assignment is used. If slotList then the slot list method is used.
dvbInaIfConSesTable	1.3.6.1.2.1.10.146.1.6.3		not-accessible	Contains information about session binding for DVB-RC MAC connections.
dvbInaIfConSesEntry	1.3.6.1.2.1.10.146.1.6.3.1		not-accessible	An entry in the table is automatically created when a new entry in the connection table connection is created if the INA and the NIU supports session binding. The entries are deleted when the contection table entry is deleted.
U32 dvbInaIfConSesUsControl	1.3.6.1.2.1.10.146.1.6.3.1.1	Unsigned32	read-only	Control which fields of the upstream session binding parameters that are used.
IPt dvbInaIfConSesUsNiuClientSrcIpType	1.3.6.1.2.1.10.146.1.6.3.1.2	InetAddressType	read-only	The type of the IP source address of the NIU client.
IP dvbInaIfConSesUsNiuClientSrcIp	1.3.6.1.2.1.10.146.1.6.3.1.3	InetAddress	read-only	The IP source address of the NIU client. Only used if bit 0 of dvbInaIfConSesUsControl is set.
IPt dvbInaIfConSesUsNiuClientDstIpType	1.3.6.1.2.1.10.146.1.6.3.1.4	InetAddressType	read-only	The type of the IP destination address of the NIU client.
IP dvbInaIfConSesUsNiuClientDstIp	1.3.6.1.2.1.10.146.1.6.3.1.5	InetAddress	read-only	The IP destination address of the NIU client. Only used if bit 1 of dvbInaIfConSesUsControl is set.
U32 dvbInaIfConSesUsNiuClientSrcPort	1.3.6.1.2.1.10.146.1.6.3.1.6	Unsigned32	read-only	The source port of the NIU client. Only used if bit 2 of dvbInaIfConSesUsControl is set.
U32 dvbInaIfConSesUsNiuClientDstPort	1.3.6.1.2.1.10.146.1.6.3.1.7	Unsigned32	read-only	The destination port of the NIU client. Only used if bit 3 of dvbInaIfConSesUsControl is set.
INT dvbInaIfConSesUsTransportProtocol	1.3.6.1.2.1.10.146.1.6.3.1.8	INTEGER	read-only	The transport protocol used by the NIU client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfConSesUsControl is set.
MAC dvbInaIfConSesUsNiuClientSrcMac	1.3.6.1.2.1.10.146.1.6.3.1.9	MacAddress	read-only	The Ethernet source MAC address of the NIU client. Only used if bit 5 of dvbInaIfConSesUsControl is set.
MAC dvbInaIfConSesUsNiuClientDstMac	1.3.6.1.2.1.10.146.1.6.3.1.10	MacAddress	read-only	The Ethernet destination MAC address of the NIU client. Only used if bit 6 of dvbInaIfConSesUsControl is set.
U32 dvbInaIfConSesUsEthernetProtocol	1.3.6.1.2.1.10.146.1.6.3.1.11	Unsigned32	read-only	The ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfConSesUsControl is set.
U32 dvbInaIfConSesUsSessionId	1.3.6.1.2.1.10.146.1.6.3.1.12	Unsigned32	read-only	The session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfConSesUsControl is set.
U32 dvbInaIfConSesDsControl	1.3.6.1.2.1.10.146.1.6.3.1.13	Unsigned32	read-only	Control which fields of the downstream session binding parameters that are used.
IPt dvbInaIfConSesDsInaClientSrcIpType	1.3.6.1.2.1.10.146.1.6.3.1.14	InetAddressType	read-only	The type of the IP source address of the INA client.
IP dvbInaIfConSesDsInaClientSrcIp	1.3.6.1.2.1.10.146.1.6.3.1.15	InetAddress	read-only	The IP source address of the INA client. Only used if bit 0 of dvbInaIfConSesDsControl is set.
IPt dvbInaIfConSesDsInaClientDstIpType	1.3.6.1.2.1.10.146.1.6.3.1.16	InetAddressType	read-only	The type of the IP destination address of the INA client.
IP dvbInaIfConSesDsInaClientDstIp	1.3.6.1.2.1.10.146.1.6.3.1.17	InetAddress	read-only	The IP destination address of the INA client. Only used if bit 1 of dvbInaIfConSesDsControl is set.
U32 dvbInaIfConSesDsInaClientSrcPort	1.3.6.1.2.1.10.146.1.6.3.1.18	Unsigned32	read-only	The source port of the INA client. Only used if bit 2 of dvbInaIfConSesDsControl is set.
U32 dvbInaIfConSesDsInaClientDstPort	1.3.6.1.2.1.10.146.1.6.3.1.19	Unsigned32	read-only	The destination port of the INA client. Only used if bit 3 of dvbInaIfConSesDsControl is set.
INT dvbInaIfConSesDsTransportProtocol	1.3.6.1.2.1.10.146.1.6.3.1.20	INTEGER	read-only	The transport protocol used by the INA client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfConSesDsControl is set.
MAC dvbInaIfConSesDsInaClientSrcMac	1.3.6.1.2.1.10.146.1.6.3.1.21	MacAddress	read-only	The Ethernet source MAC address of the INA client. Only used if bit 5 of dvbInaIfConSesDsControl is set.
MAC dvbInaIfConSesDsInaClientDstMac	1.3.6.1.2.1.10.146.1.6.3.1.22	MacAddress	read-only	The Ethernet destination MAC address of the INA client. Only used if bit 6 of dvbInaIfConSesDsControl is set.
U32 dvbInaIfConSesDsEthernetProtocol	1.3.6.1.2.1.10.146.1.6.3.1.23	Unsigned32	read-only	The ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfConSesDsControl is set.
U32 dvbInaIfConSesDsSessionId	1.3.6.1.2.1.10.146.1.6.3.1.24	Unsigned32	read-only	The session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfConSesDsControl is set.
dvbInaIfConHdrSupTable	1.3.6.1.2.1.10.146.1.6.4		not-accessible	Table contains information about the header suppression for a connection, indexed trough the Connection ID and the Context ID.
dvbInaIfConHdrSupEntry	1.3.6.1.2.1.10.146.1.6.4.1		not-accessible	An entry in the table is automatically generated when a new header suppression starts. Or when a reprovisioning is made. An entry is deleted when the connection is deleted.
INT dvbInaIfConHdrSupContextId	1.3.6.1.2.1.10.146.1.6.4.1.1	INTEGER	not-accessible	The context ID for the header suppression session.
INT dvbInaIfConHdrSupDirection	1.3.6.1.2.1.10.146.1.6.4.1.2	INTEGER	not-accessible	The direction for this the header suppression session.
OCT dvbInaIfConHdrSupControl	1.3.6.1.2.1.10.146.1.6.4.1.3	OCTET STRING	read-only	String of bits that control the use of the header suppression. Each of the first 103 bits, indicates if a byte in the header is suppressed or not. Bit 103 is used as an overall suppression enable. If a mask bit is 0, the matching header byte is suppressed. If bit 103 is set, suppression is performed. Bit 103 is the least significant bit in octet 13. See also dvbInaIfConHdrSupHeader.
I32 dvbInaIfConHdrSupGeneration	1.3.6.1.2.1.10.146.1.6.4.1.4	Integer32	read-only	The generation number that is attached to the header fields value.
I32 dvbInaIfConHdrSupHeaderLength	1.3.6.1.2.1.10.146.1.6.4.1.5	Integer32	read-only	The number of usefull bytes in the suppression header. This is the number of the last zero in the dvbInaIfConHdrSupControl.
OCT dvbInaIfConHdrSupHeader	1.3.6.1.2.1.10.146.1.6.4.1.6	OCTET STRING	read-only	The header used for header suppression. Both fixed and changing fields together. Only the first dvbInaIfConHdrSupHeaderLength is used.
dvbInaIfReprov	1.3.6.1.2.1.10.146.1.7
dvbInaIfReprovSrcNiuTable	1.3.6.1.2.1.10.146.1.7.1		not-accessible	The table describes information created on INA 1 for a NIU that is about to be reprovisioned.
dvbInaIfReprovSrcNiuEntry	1.3.6.1.2.1.10.146.1.7.1.1		not-accessible	An entry in the table is created by the manager when a NIU is about to be reprovisioned. When the reprovisioning is done and the NIU entry is deleted after dvbInaIfNiuLifetime this entry will be deleted too.
ROW dvbInaIfReprovSrcNiuRowAccessStatus	1.3.6.1.2.1.10.146.1.7.1.1.1	RowStatus	read-create	Controls and reflects the status of this row in this table.
INT dvbInaIfReprovSrcNiuCommand	1.3.6.1.2.1.10.146.1.7.1.1.2	INTEGER	read-create	Controls the reprovisioning on INA 1. When set to reprovStart the actual reporvisioning on INA 1 is initiated with a Reprovisioning Message to the NIU. Everything must be prepared for the reprovisioning when this is done. When read the response will always be reprovIdle.
DOW dvbInaIfReprovSrcNiuDsChFrequency	1.3.6.1.2.1.10.146.1.7.1.1.3	DownFrequency	read-create	The centre of the new downstream frequency when the NIU is reprovisioned to INA 2.
DOW dvbInaIfReprovSrcNiuDsChSymbolRate	1.3.6.1.2.1.10.146.1.7.1.1.4	DownstreamSymbolrate	read-create	Specifies the new symbol rate for the Downstream channel when the NIU is reprovisioned.
MOD dvbInaIfReprovSrcNiuDsChModulation	1.3.6.1.2.1.10.146.1.7.1.1.5	Modulation	read-create	Specifies the new modulation for the Downstream channel when the NIU is reprovisioned.
INT dvbInaIfReprovSrcNiuDsChType	1.3.6.1.2.1.10.146.1.7.1.1.6	INTEGER	read-create	Specifies if the new Downstream channel is inband or out-of-band when the NIU is reprovisioned.
UPF dvbInaIfReprovSrcNiuUsChFrequency	1.3.6.1.2.1.10.146.1.7.1.1.7	UpFrequency	read-create	Specifies the new upstream channel frequency in Hz when the NIU is reprovisoned.
UPS dvbInaIfReprovSrcNiuUsChSymbolRate	1.3.6.1.2.1.10.146.1.7.1.1.8	UpstreamSymbolrate	read-create	Specifies the new upstream channel symbol rate when the NIU is reprovisoned.
MOD dvbInaIfReprovSrcNiuUsChModulation	1.3.6.1.2.1.10.146.1.7.1.1.9	Modulation	read-create	Specifies the new upstream modulation when the NIU is reprovisoned.
I32 dvbInaIfReprovSrcNiuUsChId	1.3.6.1.2.1.10.146.1.7.1.1.10	Integer32	read-only	Specifies the new logical channel number associated with the upstream channel when the NIU is reprovisioned.
dvbInaIfReprovDstNiuTable	1.3.6.1.2.1.10.146.1.7.2		not-accessible	The table describes information created on INA 2 for a NIU that is about to be reprovisioned.
dvbInaIfReprovDstNiuEntry	1.3.6.1.2.1.10.146.1.7.2.1		not-accessible	An entry in the table is created by the manager when a NIU is about to be reprovisioned. When the reprovisioning is done and the NIU signs on to INA 2 the information is transfered to the NIU table and the entry in this table is deleted automatically.
MAC dvbInaIfReprovDstNiuMacAddress	1.3.6.1.2.1.10.146.1.7.2.1.1	MacAddress	not-accessible	A 48-bit value representing the unique MAC address of the NIU to be reprovisioned. This is the index of the table.
ROW dvbInaIfReprovDstNiuRowAccessStatus	1.3.6.1.2.1.10.146.1.7.2.1.2	RowStatus	read-create	Controls and reflects the status of this row in this table.
INT dvbInaIfReprovDstNiuCommand	1.3.6.1.2.1.10.146.1.7.2.1.3	INTEGER	read-create	Controls the reprovisioning on INA 2. When set to reprovPrepare INA 2 will generate the necessary information that needs to be transferred back to INA 1. This includes: New Connection ID's New PID for each connection New downstream VPI/VCI New upstream VPI/VCI New upstream number Furthermore new fixed rate parameters are calculated if one of the new connections are fixed rate. All settings needed to calculate these new parameters must be given before reprovPrepare is set. When set to reprovReceiveNiu this is an indication to INA 2 that the NIU is expected to sign-on now. When read the response will always be reprovIdle.
NUM dvbInaIfReprovDstNiuDownIfIndex	1.3.6.1.2.1.10.146.1.7.2.1.4	InterfaceIndexOrZero	read-create	Specifies the IfIndex of the downstream channel on which the NIU is tuned after the reprovisioning.
NUM dvbInaIfReprovDstNiuUpIfIndex	1.3.6.1.2.1.10.146.1.7.2.1.5	InterfaceIndexOrZero	read-create	Specifies the IfIndex of the upstream channel that is used by the NIU after the reprovisioning.
U32 dvbInaIfReprovDstNiuLifetime	1.3.6.1.2.1.10.146.1.7.2.1.6	Unsigned32	read-create	Defines how long time after the NIU signs off, the NIU entry is removed from the NIU table. An infinite(0) value would mean that the values are stored at least until the next reboot of the INA
dvbInaIfReprovSrcConTable	1.3.6.1.2.1.10.146.1.7.3		not-accessible	Contains information about DVB-RC MAC connections on INA 1 that is about to be reprovisioned.
dvbInaIfReprovSrcConEntry	1.3.6.1.2.1.10.146.1.7.3.1		not-accessible	The entries in the table are created by the manager when a NIU on INA 1 is about to be reprovisioned. After the NIU is reprovisoned the entries are automatically deleted when the corresponding NUI entry are deleted after dvbInaIfNiuLifetime.
ROW dvbInaIfReprovSrcConRowAccessStatus	1.3.6.1.2.1.10.146.1.7.3.1.1	RowStatus	read-create	Controls and reflects the status of this row in this table.
U32 dvbInaIfReprovSrcConConnectionIdNew	1.3.6.1.2.1.10.146.1.7.3.1.2	Unsigned32	read-create	Specifies the new value for the connection identifier to be used for this connection after the reprovisioning. The management system must get this value from INA 2.
U32 dvbInaIfReprovSrcConPID	1.3.6.1.2.1.10.146.1.7.3.1.3	Unsigned32	read-create	Specifies the new MPEG PID of the elementary stream that carries the data after the reprovisioning.
U32 dvbInaIfReprovSrcConDsVc	1.3.6.1.2.1.10.146.1.7.3.1.4	Unsigned32	read-create	ATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission after reprovisioning. The management system must get this value from INA 2.
U32 dvbInaIfReprovSrcConUsVc	1.3.6.1.2.1.10.146.1.7.3.1.5	Unsigned32	read-create	ATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission after reprovisioning. The management system must get this value from INA 2.
dvbInaIfReprovDstConTable	1.3.6.1.2.1.10.146.1.7.4		not-accessible	Contains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2.
dvbInaIfReprovDstConEntry	1.3.6.1.2.1.10.146.1.7.4.1		not-accessible	The entries in the table are created by the manager when a NIU is about to be reprovisioned to INA 2. After the NIU has signed on to INA 2, the information in the tables are used to create entries in the normal connection tables. When the entries in the normal tables are made the entries in the reprovisioning table are automatically deleted.
U32 dvbInaIfReprovDstConConnectionIdOld	1.3.6.1.2.1.10.146.1.7.4.1.1	Unsigned32	not-accessible	Specifies the old value for the connection identifier that is used on INA 1. The management system must get this value from INA 1.
ROW dvbInaIfReprovDstConRowAccessStatus	1.3.6.1.2.1.10.146.1.7.4.1.2	RowStatus	read-create	Controls and reflects the status of this row in this table.
U32 dvbInaIfReprovDstConConnectionIdNew	1.3.6.1.2.1.10.146.1.7.4.1.3	Unsigned32	read-only	Specifies the new value for the connection identifier that is used on INA 2. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare.
BIT dvbInaIfReprovDstConConnectionType	1.3.6.1.2.1.10.146.1.7.4.1.4	Bits	read-create	Specifies the kind of connection: fixed rate, contention based, or reservation based. This parameter can be set to a value that is an OR of the following bits: 'conTypeFixedRate(0)' 'conTypeContention(1)' 'conTypeReservation(2)' Default this object is 'conTypeContention(1)'.
INT dvbInaIfReprovDstConEncapsulation	1.3.6.1.2.1.10.146.1.7.4.1.5	INTEGER	read-create	This object indicates the type of encapsulation provided on this connection. This object can have one of the following values: 'directIp(1)', 'ethernetMacBridging(2)', or 'ppp(3)'. By default this parameter is set to 'directIp(1)'.
U32 dvbInaIfReprovDstConAtmDownstreamVCC	1.3.6.1.2.1.10.146.1.7.4.1.6	Unsigned32	read-only	ATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare.
U32 dvbInaIfReprovDstConAtmUpstreamVCC	1.3.6.1.2.1.10.146.1.7.4.1.7	Unsigned32	read-only	ATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare.
MAC dvbInaIfReprovDstConFilterMACAddress	1.3.6.1.2.1.10.146.1.7.4.1.8	MacAddress	read-create	Specifies the 'soft' MPEG MPE MAC address used to filter the data out of the downstream IB transmission. This is found in the Downstream_Multiprotocol_CBD substructure in the Connect Message.
U32 dvbInaIfReprovDstConPID	1.3.6.1.2.1.10.146.1.7.4.1.9	Unsigned32	read-only	Specifies the MPEG PID of the elementary stream that carries the data. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare.
INT dvbInaIfReprovDstConMaxContentionMsgLen	1.3.6.1.2.1.10.146.1.7.4.1.10	INTEGER	read-create	The Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using contention access. Any message greater than this should use reservation access. The default value should be dvbInaIfMacMaxContentionMsgLen.
INT dvbInaIfReprovDstConMaxReservationMsgLen	1.3.6.1.2.1.10.146.1.7.4.1.11	INTEGER	read-create	This is the maximum length of a message that may be transmitted using a single reservation access. Any message greater than this should be transmitted by making multiple reservation requests. The default value should be dvbInaIfMacMaxReservationMsgLen.
INT dvbInaIfReprovDstConAuxFlags	1.3.6.1.2.1.10.146.1.7.4.1.12	INTEGER	read-only	The Connection_Control_Field_Aux from the Connect Message Structure. This is used to indicate if the Priority, Downstream flowspec and Session binding objects are used for the connection.
dvbInaIfReprovDstConSesTable	1.3.6.1.2.1.10.146.1.7.5		not-accessible	Contains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2.
dvbInaIfReprovDstConSesEntry	1.3.6.1.2.1.10.146.1.7.5.1		not-accessible	The entries in the table are created automatically when an entry in the dvbInaIfReprovDstConTable is created and the INA support session binding. You must always create an entry in the dvbInaIfReprovDstConTable first and this will automatically create an entry in the dvbInaIfReprovDstConSesTable table. After the NIU has signed on to INA 2, the information in the table are used to create entries in the normal connection tables. When the entries in the normal tables are made the entries in the reprovisioning table are automatically deleted.
U32 dvbInaIfReprovDstConSesUsControl	1.3.6.1.2.1.10.146.1.7.5.1.1	Unsigned32	read-write	Control which fields of the upstream session binding parameters that are used.
IPt dvbInaIfReprovDstConSesUsNiuClientSrcIpType	1.3.6.1.2.1.10.146.1.7.5.1.2	InetAddressType	read-write	The type of the IP source address of the NIU client.
IP dvbInaIfReprovDstConSesUsNiuClientSrcIp	1.3.6.1.2.1.10.146.1.7.5.1.3	InetAddress	read-write	The IP source address of the NIU client. Only used if bit 0 of dvbInaIfReprovDstConSesUsControl is set.
IPt dvbInaIfReprovDstConSesUsNiuClientDstIpType	1.3.6.1.2.1.10.146.1.7.5.1.4	InetAddressType	read-write	The type of the IP destination address of the NIU client.
IP dvbInaIfReprovDstConSesUsNiuClientDstIp	1.3.6.1.2.1.10.146.1.7.5.1.5	InetAddress	read-write	The IP destination address of the NIU client. Only used if bit 1 of dvbInaIfReprovDstConSesUsControl is set.
U32 dvbInaIfReprovDstConSesUsNiuClientSrcPort	1.3.6.1.2.1.10.146.1.7.5.1.6	Unsigned32	read-write	The source port of the NIU client. Only used if bit 2 of dvbInaIfReprovDstConSesUsControl is set.
U32 dvbInaIfReprovDstConSesUsNiuClientDstPort	1.3.6.1.2.1.10.146.1.7.5.1.7	Unsigned32	read-write	The destination port of the NIU client. Only used if bit 3 of dvbInaIfReprovDstConSesUsControl is set.
INT dvbInaIfReprovDstConSesUsTransportProtocol	1.3.6.1.2.1.10.146.1.7.5.1.8	INTEGER	read-write	The transport protocol used by the NIU client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfReprovDstConSesUsControl is set.
MAC dvbInaIfReprovDstConSesUsNiuClientSrcMac	1.3.6.1.2.1.10.146.1.7.5.1.9	MacAddress	read-write	The Ethernet source MAC address of the NIU client. Only used if bit 5 of dvbInaIfReprovDstConSesUsControl is set.
MAC dvbInaIfReprovDstConSesUsNiuClientDstMac	1.3.6.1.2.1.10.146.1.7.5.1.10	MacAddress	read-write	The Ethernet destination MAC address of the NIU client. Only used if bit 6 of dvbInaIfReprovDstConSesUsControl is set.
U32 dvbInaIfReprovDstConSesUsEthernetProtocol	1.3.6.1.2.1.10.146.1.7.5.1.11	Unsigned32	read-write	The ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfReprovDstConSesUsControl is set.
U32 dvbInaIfReprovDstConSesUsSessionId	1.3.6.1.2.1.10.146.1.7.5.1.12	Unsigned32	read-write	The session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfReprovDstConSesUsControl is set.
U32 dvbInaIfReprovDstConSesDsControl	1.3.6.1.2.1.10.146.1.7.5.1.13	Unsigned32	read-write	Control which fields of the downstream session binding parameters that are used.
IPt dvbInaIfReprovDstConSesDsInaClientSrcIpType	1.3.6.1.2.1.10.146.1.7.5.1.14	InetAddressType	read-write	The type of the IP source address of the INA client.
IP dvbInaIfReprovDstConSesDsInaClientSrcIp	1.3.6.1.2.1.10.146.1.7.5.1.15	InetAddress	read-write	The IP source address of the INA client. Only used if bit 0 of dvbInaIfReprovDstConSesDsControl is set.
IPt dvbInaIfReprovDstConSesDsInaClientDstIpType	1.3.6.1.2.1.10.146.1.7.5.1.16	InetAddressType	read-write	The type of the IP destination address of the INA client.
IP dvbInaIfReprovDstConSesDsInaClientDstIp	1.3.6.1.2.1.10.146.1.7.5.1.17	InetAddress	read-write	The IP destination address of the INA client. Only used if bit 1 of dvbInaIfReprovDstConSesDsControl is set.
U32 dvbInaIfReprovDstConSesDsInaClientSrcPort	1.3.6.1.2.1.10.146.1.7.5.1.18	Unsigned32	read-write	The source port of the INA client. Only used if bit 2 of dvbInaIfReprovDstConSesDsControl is set.
U32 dvbInaIfReprovDstConSesDsInaClientDstPort	1.3.6.1.2.1.10.146.1.7.5.1.19	Unsigned32	read-write	The destination port of the INA client. Only used if bit 3 of dvbInaIfReprovDstConSesDsControl is set.
INT dvbInaIfReprovDstConSesDsTransportProtocol	1.3.6.1.2.1.10.146.1.7.5.1.20	INTEGER	read-write	The transport protocol used by the INA client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfReprovDstConSesDsControl is set.
MAC dvbInaIfReprovDstConSesDsInaClientSrcMac	1.3.6.1.2.1.10.146.1.7.5.1.21	MacAddress	read-write	The Ethernet source MAC address of the INA client. Only used if bit 5 of dvbInaIfReprovDstConSesDsControl is set.
MAC dvbInaIfReprovDstConSesDsInaClientDstMac	1.3.6.1.2.1.10.146.1.7.5.1.22	MacAddress	read-write	The Ethernet destination MAC address of the INA client. Only used if bit 6 of dvbInaIfReprovDstConSesDsControl is set.
U32 dvbInaIfReprovDstConSesDsEthernetProtocol	1.3.6.1.2.1.10.146.1.7.5.1.23	Unsigned32	read-write	The ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfReprovDstConSesDsControl is set.
U32 dvbInaIfReprovDstConSesDsSessionId	1.3.6.1.2.1.10.146.1.7.5.1.24	Unsigned32	read-write	The session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfReprovDstConSesDsControl is set.
dvbInaIfReprovDstConHdrSupTable	1.3.6.1.2.1.10.146.1.7.6		not-accessible	Contains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2.
dvbInaIfReprovDstConHdrSupEntry	1.3.6.1.2.1.10.146.1.7.6.1		not-accessible	The entries in the table are created by the manager when a NIU is about to be reprovisioned to INA 2. After the NIU has signed on to INA 2, the information in the tables are used to create entries in the normal connection tables. When the entries in the normal tables are made the entries in the reprovisioning table are automatically deleted.
INT dvbInaIfReprovDstConHdrSupContextId	1.3.6.1.2.1.10.146.1.7.6.1.1	INTEGER	not-accessible	The context ID for the header suppression session.
INT dvbInaIfReprovDstConHdrSupDirection	1.3.6.1.2.1.10.146.1.7.6.1.2	INTEGER	not-accessible	The direction for this the header suppression session.
ROW dvbInaIfReprovDstConHdrSupRowAccessStatus	1.3.6.1.2.1.10.146.1.7.6.1.3	RowStatus	read-create	Controls and reflects the status of this row in this table.
OCT dvbInaIfReprovDstConHdrSupControl	1.3.6.1.2.1.10.146.1.7.6.1.4	OCTET STRING	read-only	String of bits that control the use of the header suppression. Each of the fisrt 103 bits, indicates if a byte in the header is suppressed or not. Bit 103 is used as an overall suppression enable. If a mask bit is 0, the matching header byte is suppressed. If bit 103 is set, suppression is performed. Bit 103 is the least significant bit in octet 13. See also dvbInaIfReprovDstConHdrSupHeader.
I32 dvbInaIfReprovDstConHdrSupGeneration	1.3.6.1.2.1.10.146.1.7.6.1.5	Integer32	read-only	The generation number that is attached to the header fields value.
I32 dvbInaIfReprovDstConHdrSupHeaderLength	1.3.6.1.2.1.10.146.1.7.6.1.6	Integer32	read-only	The number of usefull bytes in the suppression header. This is the number of the last zero in the dvbInaIfReprovDstConHdrSupControl.
OCT dvbInaIfReprovDstConHdrSupHeader	1.3.6.1.2.1.10.146.1.7.6.1.7	OCTET STRING	read-only	The header used for header suppression. Both fixed and changing fields together. Only the first dvbInaIfReprovDstConHdrSupHeaderLength is used.
dvbInaIfReprovDstConQosTable	1.3.6.1.2.1.10.146.1.7.7		not-accessible	Contains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2.
dvbInaIfReprovDstConQosEntry	1.3.6.1.2.1.10.146.1.7.7.1		not-accessible	The entries in the table are created automatically when an entry in the dvbInaIfReprovDstConTable is created and the INA support QoS settings. After the NIU has signed on to INA 2, the information in the tables are used to create entries in the normal connection tables. When the entries in the normal tables are made the entries in the reprovisioning table are automatically deleted.
INT dvbInaIfReprovDstConQosPriority	1.3.6.1.2.1.10.146.1.7.7.1.1	INTEGER	read-create	The priority of the connection. Connections with low priority field value can be reprovisioned in order to accommodate the requirements of connections with high priority field. Standard data flow applications 0-79 Applications with QoS requirements 80-200 High priority applications 201-255
U32 dvbInaIfReprovDstConQosDsReqMaxPacketSize	1.3.6.1.2.1.10.146.1.7.7.1.2	Unsigned32	read-create	A downstream QoS parameter. Defines the requested maximum packet size in the downstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request. The packet size includes propriety protocols header, transport protocol (UDP/TCP) header, and the IP header. The packet size does not include the Ethernet header.
U32 dvbInaIfReprovDstConQosDsReqBitrate	1.3.6.1.2.1.10.146.1.7.7.1.3	Unsigned32	read-create	A downstream QoS parameter. Defines requested average bit rate in the downstream.
INT dvbInaIfReprovDstConQosDsReqJitter	1.3.6.1.2.1.10.146.1.7.7.1.4	INTEGER	read-create	A downstream QoS parameter. Defines the requested maximum allowed jitter in the downstream.
U32 dvbInaIfReprovDstConQosUsReqBw	1.3.6.1.2.1.10.146.1.7.7.1.5	Unsigned32	read-create	An upstream QoS parameter. The requested bandwidth for the upstream.
U32 dvbInaIfReprovDstConQosUsReqMaxDistSlots	1.3.6.1.2.1.10.146.1.7.7.1.6	Unsigned32	read-create	An upstream QoS parameter. The requested maximum distance between slots for the upstream.
U32 dvbInaIfReprovDstConQosUsReqFrameLength	1.3.6.1.2.1.10.146.1.7.7.1.7	Unsigned32	read-create	An upstream QoS parameter. The requested frame length for the upstream.
INT dvbInaIfReprovDstConQosUsReqFixedRateMethod	1.3.6.1.2.1.10.146.1.7.7.1.8	INTEGER	read-create	An upstream QoS parameter. Request a specific fixed rate slot assignment method to be used. If cyclic then cyclic assignment is used. If slotList then the slot list method is used.
dvbInaIfMIBConform	1.3.6.1.2.1.10.146.2
dvbInaIfCompliances	1.3.6.1.2.1.10.146.2.1
dvbInaIfCompliance	1.3.6.1.2.1.10.146.2.1.1			The compliance statement for EuroModem INAs which implement the DVB-CABLE-INA-IF-MIB MIB. An implementation only has to support IPv4 addresses to be compliant.
dvbInaIfGroups	1.3.6.1.2.1.10.146.2.2
dvbInaIfMacGroup	1.3.6.1.2.1.10.146.2.2.1			A collection of objects providing capabilities and statistics for the MAC layer.
dvbInaIfProvisionGroup	1.3.6.1.2.1.10.146.2.2.2
dvbInaIfDsChGroup	1.3.6.1.2.1.10.146.2.2.3
dvbInaIfUsChGroup	1.3.6.1.2.1.10.146.2.2.4
dvbInaIfNiuGroup	1.3.6.1.2.1.10.146.2.2.5
dvbInaIfConnectionGroup	1.3.6.1.2.1.10.146.2.2.6
dvbInaIfConQosGroup	1.3.6.1.2.1.10.146.2.2.7
dvbInaIfConSesGroup	1.3.6.1.2.1.10.146.2.2.8
dvbInaIfConHdrSupGroup	1.3.6.1.2.1.10.146.2.2.9
dvbInaIfReprovSrcNiuGroup	1.3.6.1.2.1.10.146.2.2.10
dvbInaIfReprovDstNiuGroup	1.3.6.1.2.1.10.146.2.2.11
dvbInaIfReprovSrcConGroup	1.3.6.1.2.1.10.146.2.2.12
dvbInaIfReprovDstConGroup	1.3.6.1.2.1.10.146.2.2.13
dvbInaIfReprovDstConSesGroup	1.3.6.1.2.1.10.146.2.2.14
dvbInaIfReprovDstConHdrSupGroup	1.3.6.1.2.1.10.146.2.2.15
dvbInaIfReprovDstConQosGroup	1.3.6.1.2.1.10.146.2.2.16

RFC description

Manages DVB cable interactive network adapter interfaces conforming to EuroModem specification.

Start monitoring DVB/DAVIC EuroModem cable Interactive Network Adapter (vendor-neutral standard) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DVB-CABLE-INA-IF-MIB