DLINKPRIME-SYSLOG-MIB

All MIBs › DLINKPRIME-SYSLOG-MIB

Organization: D-Link Corp.

Last Updated: 2014-04-26

Category: D-Link, Syslog

Description: Manages syslog server configuration and log severity filters on D-Link Prime network devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DLINKPRIME-SYSLOG-MIB?

This D-Link Prime MIB manages syslog server configuration on the switch, including remote syslog server addresses and severity-level filtering for log messages. No sample object names were provided in this extraction, so specific table/column names cannot be enumerated, but the module's stated purpose is configuration of the system log function. This is fundamentally a software/logging-configuration MIB; it indirectly supports monitoring device software health by determining what log severities get forwarded for centralized analysis, rather than exposing sensor data itself. It has no described dependency on external standard MIBs beyond general syslog concepts (RFC 5424 is the protocol referenced conceptually, though this is a private D-Link definition). It is typically deployed when centralizing log collection from D-Link Prime switches into a syslog server or SIEM for auditing and fault diagnosis. Network engineers evaluating or troubleshooting this functionality can download the DLINKPRIME-SYSLOG-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DLINKPRIME-SYSLOG-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link Prime series managed switch

Monitoring Examples

No sample_objects were supplied for this MIB, so a concrete object-level monitoring scenario cannot be honestly constructed; typically such a MIB would let an admin verify configured syslog server addresses and minimum severity level being forwarded, but exact object names cannot be confirmed here.

Imported Objects

From DLINK-ID-REC-MIB

dlinkPrimeCommon

OBJECT-IDENTITY

From IF-MIB

InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TruthValue

From SYSLOG-TC-MIB

SyslogFacility
SyslogSeverity

OIDs

OID symbolic	OID numeric	Type	Access	Description
dlinkPrimeSyslogMIB	1.3.6.1.4.1.171.28.21			This MIB module defines objects for system log function.
dpSyslogMIBNotifications	1.3.6.1.4.1.171.28.21.0
dpSyslogMIBObjects	1.3.6.1.4.1.171.28.21.1
dpSyslogGeneral	1.3.6.1.4.1.171.28.21.1.1
T/F dpSyslogLogOnEnabled	1.3.6.1.4.1.171.28.21.1.1.1	TruthValue	read-write	This object enables or disables the System Log function during system runtime.
dpSyslogLogbuffer	1.3.6.1.4.1.171.28.21.1.2			This object identifier represents the group of objects that are related to the logging system message to local buffer.
INT dpSyslogClearLogBuffer	1.3.6.1.4.1.171.28.21.1.2.1	INTEGER	read-write	This object is used to clear log messages at logging buffer when set to 'clear'. No action is taken if this object is set to 'noOp'. When read, the value 'noOp' is returned.
T/F dpSyslogLogBufferEnabled	1.3.6.1.4.1.171.28.21.1.2.2	TruthValue	read-write	This object indicates the state of logging system messages to the local buffer. Messages must enter the local message buffer first before it can be further dispatched to other destinations.
dpSyslogServer	1.3.6.1.4.1.171.28.21.1.3
IP dpSyslogServerAddress	1.3.6.1.4.1.171.28.21.1.3.1	IpAddress	read-write	This object indicates the IPv4 address of the SYSLOG server.
U32 dpSyslogServerPort	1.3.6.1.4.1.171.28.21.1.3.2	Unsigned32	read-write	This object indicates the UDP port number to be used for the SYSLOG server.
INT dpSyslogServerSeverity	1.3.6.1.4.1.171.28.21.1.3.3	INTEGER	read-write	This object indicates the severity of log messages that will be sent to the server.
INT dpSyslogServerFacility	1.3.6.1.4.1.171.28.21.1.3.4	INTEGER	read-write	Specifies the logging facility of the log host.
U32 dpSyslogBufferTableNum	1.3.6.1.4.1.171.28.21.1.4	Unsigned32	read-only	This object indicates the number of entries presented in the dpSyslogBufferTable.
dpSyslogBufferTable	1.3.6.1.4.1.171.28.21.1.5		not-accessible	A table consists of a list of system log messages.
dpSyslogBufferEntry	1.3.6.1.4.1.171.28.21.1.5.1		not-accessible	An entry defines a log message.
STR dpSyslogBufferLevel	1.3.6.1.4.1.171.28.21.1.5.1.1	DisplayString	read-only	An index that uniquely identifies the message.
STR dpSyslogBufferDateAndTime	1.3.6.1.4.1.171.28.21.1.5.1.2	DisplayString	read-only	The date and time when the message is logged.
STR dpSyslogBufferDescription	1.3.6.1.4.1.171.28.21.1.5.1.3	DisplayString	read-only	The content of the log message.
dpSyslogMIBConformance	1.3.6.1.4.1.171.28.21.2
dpSyslogMIBCompliances	1.3.6.1.4.1.171.28.21.2.1
dpSyslogMIBCompliance	1.3.6.1.4.1.171.28.21.2.1.1			The compliance statement for entities which implement the DLINKPRIME-SYSLOG-MIB.
dpSyslogMIBGroups	1.3.6.1.4.1.171.28.21.2.1.2
dpSyslogGeneralGroup	1.3.6.1.4.1.171.28.21.2.1.2.1			A collection of objects provides basic configuration of SYSLOG feature.
dpSyslogLogServerGroup	1.3.6.1.4.1.171.28.21.2.1.2.2			A collection of objects provides configurations that are related to the logging system messages to the SYSLOG servers.

RFC description

D-Link system logging configuration, enabling syslog function management and log buffer control for network devices.

Start monitoring D-Link Prime series managed switch (syslog server config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DLINKPRIME-SYSLOG-MIB

What Is DLINKPRIME-SYSLOG-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description