DLINKPRIME-DEVICE-INFORMATION-MIB

All MIBs › DLINKPRIME-DEVICE-INFORMATION-MIB

Organization: D-Link Corp.

Last Updated: 2014-05-30

Description: D-Link Prime MIB exposing general device information such as system identity, IP addresses, and hardware details for D-Link network equipment

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DLINKPRIME-DEVICE-INFORMATION-MIB?

DLINKPRIME-DEVICE-INFORMATION-MIB is a D-Link "Prime" enterprise MIB exposing general device-identity information for D-Link network equipment, such as system identity, IP addressing, and hardware detail fields. No sample objects were extracted, so specific object names cannot be confirmed, but per its stated purpose it would expose scalar objects for device model, serial number, firmware/software version, and management IP address(es), typical of a device-information/inventory MIB. Its monitoring value would be primarily inventory/software-version tracking, confirming which firmware version and hardware model a given device is running, rather than dynamic performance counters. It is likely a foundational module within the broader D-Link "Prime" enterprise MIB suite, referenced by other D-Link Prime MIBs for device identification context. It would be deployed on D-Link switches/routers/APs managed under the D-Link Prime network management ecosystem. Engineers can download the DLINKPRIME-DEVICE-INFORMATION-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DLINKPRIME-DEVICE-INFORMATION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link network equipment managed under the D-Link Prime ecosystem

Monitoring Examples

No object or table names were available in the extracted metadata for this module, so a concrete monitoring scenario cannot be honestly constructed beyond the general expectation of device identity/firmware-version objects implied by the module's short description.

Imported Objects

From DLINK-ID-REC-MIB

dlinkPrimeCommon

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP
TEXTUAL-CONVENTION

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
dlinkPrimeDeviceInfoMIB	1.3.6.1.4.1.171.28.3			This MIB module defines objects for device information function.
dpDeviceInfoMIBObjects	1.3.6.1.4.1.171.28.3.1
dpDeviceInfoSysConfiguration	1.3.6.1.4.1.171.28.3.1.1
INT dpDeviceInfoIpV4AddrCfgMode	1.3.6.1.4.1.171.28.3.1.1.1	INTEGER	read-write	Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.
IP dpDeviceInfoIpV4Addr	1.3.6.1.4.1.171.28.3.1.1.2	IpAddress	read-write	Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.
IP dpDeviceInfoIpV4SubnetMask	1.3.6.1.4.1.171.28.3.1.1.3	IpAddress	read-write	IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.
IP dpDeviceInfoGateway	1.3.6.1.4.1.171.28.3.1.1.4	IpAddress	read-write	Gateway
U32 dpDeviceInfoDhcpRetry	1.3.6.1.4.1.171.28.3.1.1.5	Unsigned32	read-write	This object indicates the DHCP retry Times when DHCP client is enabled.
INT dpDeviceInfoIpV6GlobalState	1.3.6.1.4.1.171.28.3.1.1.6	INTEGER	read-write	The state of IPv6 that you want this interface to be in. It must be a exist vlan id.
ADR dpDeviceInfoIpV6AddressIpAddr	1.3.6.1.4.1.171.28.3.1.1.7	Ipv6Address	read-write	Static IPv6 Address.
MAC dpDeviceInfoMacAddr	1.3.6.1.4.1.171.28.3.1.2	MacAddress	read-only	The MAC address of this system.
STR dpDeviceInfoBootPromVersion	1.3.6.1.4.1.171.28.3.1.3	DisplayString	read-only	A textual string containing the PROM version of the system.
STR dpDeviceInfoFirmwareVersion	1.3.6.1.4.1.171.28.3.1.4	DisplayString	read-only	A textual string containing the firmware version of the system.
STR dpDeviceInfoHardwareVersion	1.3.6.1.4.1.171.28.3.1.5	DisplayString	read-only	A textual string containing the hardware version of the system.
STR dpDeviceInfoSerialNumber	1.3.6.1.4.1.171.28.3.1.6	DisplayString	read-only	A text string containing the serial number of the system.

RFC description

D-Link Prime device information MIB for IPv4/IPv6 configuration and system settings.

Start monitoring D-Link Prime ecosystem device (identity/inventory) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DLINKPRIME-DEVICE-INFORMATION-MIB

What Is DLINKPRIME-DEVICE-INFORMATION-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description