DGS3612G-L2MGMT-MIB

All MIBs › DGS3612G-L2MGMT-MIB

Last Updated: 2000-07-15

Category: Technology: Switching/L2, Vendor: D-Link

Description: L2 management MIB for D-Link DGS-3612G Gigabit switch covering VLANs, STP, and L2 management features.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DGS3612G-L2MGMT-MIB?

This is a vendor-specific MIB from D-Link for Layer 2 management on the DGS-3612G Gigabit switch, covering VLAN configuration and related switching features. It exposes VLAN definitions and their name, type, and per-port membership (tagged, untagged, static, and forbidden ports), giving a structural view of the switch's Layer 2 segmentation. Its monitoring value is mainly configuration-state visibility rather than fault/hardware telemetry: administrators check swL2VlanCurrentTaggedPorts/swL2VlanCurrentUntaggedPorts to confirm the switch's live VLAN port assignments match intended configuration, which helps diagnose connectivity problems caused by VLAN misconfiguration. It builds on standard bridge/VLAN concepts akin to the IEEE 802.1Q and IETF BRIDGE-MIB model, though implemented as a private D-Link structure. It is deployed on D-Link DGS-3612G switches in enterprise or campus wiring closets where VLAN segmentation is used to isolate traffic. Network engineers evaluating or troubleshooting this functionality can download the DGS3612G-L2MGMT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DGS3612G-L2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DGS-3612G Gigabit Ethernet switch

Monitoring Examples

An admin walks swL2VlanTable/swL2VlanEntry, keyed by swL2VlanIndex, reading swL2VlanName and swL2VlanType to inventory configured VLANs, then compares swL2VlanStaticTaggedPorts/swL2VlanStaticPorts against the live swL2VlanCurrentTaggedPorts/swL2VlanCurrentUntaggedPorts to spot a port that hasn't picked up its intended VLAN membership after a config push. swL2VlanForbiddenPorts is checked to confirm a port meant to be excluded from a VLAN (e.g., for security segmentation) hasn't been accidentally added. swL2VlanAdvertisementState shows whether GVRP/VLAN advertisement is enabled on that VLAN, explaining unexpected VLAN propagation across trunk links.

What Can Be Monitored

VLAN name and type
VLAN static/tagged/untagged port membership
VLAN forbidden ports
current (operational) tagged/untagged port assignments
VLAN advertisement state

Imported Objects

From DLINK-ID-REC-MIB

AgentNotifyLevel

From RFC1155-SMI

Counter

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION

From SW36XXPRIMGMT-MIB

dgs3612g

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using swL2PortBufferFullDrops OID:

Select a D-Link DGS-3612G Gigabit Ethernet switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type swL2PortBufferFullDrops into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of packets discarded while buffer full. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL2MgmtMIB	1.3.6.1.4.1.171.11.70.9.2			The Structure of Layer 2 Network Management Information.
swL2DevMgmt	1.3.6.1.4.1.171.11.70.9.2.1
swL2DevInfo	1.3.6.1.4.1.171.11.70.9.2.1.1
INT swDevInfoTotalNumOfPort	1.3.6.1.4.1.171.11.70.9.2.1.1.1	INTEGER	read-only	The number of ports within this switch. This value is the sum of the ports within this switch.
INT swDevInfoNumOfPortInUse	1.3.6.1.4.1.171.11.70.9.2.1.1.2	INTEGER	read-only	The number of ports in this switch connected to the segment or the end stations.
swDevModuleInfoTable	1.3.6.1.4.1.171.11.70.9.2.1.1.3		not-accessible	This table contains the module information.
swDevModuleInfoEntry	1.3.6.1.4.1.171.11.70.9.2.1.1.3.1		not-accessible	A list of management information for each unit in the system.
INT swDevModuleInfoUnitID	1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.1	INTEGER	read-only	This object indicates the specific unit ID in the stacking/chassis table.
INT swDevModuleInfoModuleID	1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.2	INTEGER	read-only	This object indicates the module ID of this unit.
STR swDevModuleInfoModuleName	1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.3	DisplayString	read-only	A textual string containing name of the the module.
STR swDevModuleInfoReversion	1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.4	DisplayString	read-only	A textual string containing reversion of the module.
STR swDevModuleInfoSerial	1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.5	DisplayString	read-only	A textual string containing serial of the module.
STR swDevModuleInfoDescription	1.3.6.1.4.1.171.11.70.9.2.1.1.3.1.6	DisplayString	read-only	A textual string containing description of the module.
STR swDevInfoBootPromVersion	1.3.6.1.4.1.171.11.70.9.2.1.1.4	DisplayString	read-only	Boot Prom Version.
STR swDevInfoFirmwareVersion	1.3.6.1.4.1.171.11.70.9.2.1.1.5	DisplayString	read-only	Boot firmware Version.
OCT swDevInfoFrontPanelLedStatus	1.3.6.1.4.1.171.11.70.9.2.1.1.6	OCTET STRING	read-only	This object is a set of system LED indications. The first two octets is defined as system LED. The first LED is power LED. The second LED is console LED. The third LED is RPS (Redundancy Power Supply) LED. The other octets following the second octets are the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. 04 = 10Gbps. The four remaining bits are currently unused and must be 0.
swL2DevCtrl	1.3.6.1.4.1.171.11.70.9.2.1.2
INT swL2DevCtrlStpState	1.3.6.1.4.1.171.11.70.9.2.1.2.1	INTEGER	read-write	This object can be enabled or disabled spanning tree algorithm during runtime of the system.
INT swL2DevCtrlIGMPSnooping	1.3.6.1.4.1.171.11.70.9.2.1.2.2	INTEGER	read-write	This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.
INT swL2DevCtrlIGMPSnoopingMcstRTOnly	1.3.6.1.4.1.171.11.70.9.2.1.2.3	INTEGER	read-write
INT swL2DevCtrlRmonState	1.3.6.1.4.1.171.11.70.9.2.1.2.4	INTEGER	read-write	This object can be enabled or disabled RMON.
INT swL2DevCtrlCleanAllStatisticCounter	1.3.6.1.4.1.171.11.70.9.2.1.2.5	INTEGER	read-write	As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
VLA swL2DevCtrlVlanIdOfFDBTbl	1.3.6.1.4.1.171.11.70.9.2.1.2.6	VlanId	read-write	Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is DEFAULT_VLAN_ID of system .
VLA swL2DevCtrlManagementVlanId	1.3.6.1.4.1.171.11.70.9.2.1.2.7	VlanId	read-write	This object controls which Vlan includes system ip. And the Vlan should have been created.
INT swL2MACNotifyState	1.3.6.1.4.1.171.11.70.9.2.1.2.8	INTEGER	read-write	This object can enabled or disabled MAC Notification.
INT swL2MACNotifyHistorySize	1.3.6.1.4.1.171.11.70.9.2.1.2.9	INTEGER	read-write	This object indicates the history size of variation MAC in address table. The default value is 1 .
INT swL2MACNotifyInterval	1.3.6.1.4.1.171.11.70.9.2.1.2.10	INTEGER	read-write	This object indicates the time interval in second for trigger the MAC notify message.
swL2DevCtrlWeb	1.3.6.1.4.1.171.11.70.9.2.1.2.13
INT swL2DevCtrlWebState	1.3.6.1.4.1.171.11.70.9.2.1.2.13.1	INTEGER	read-write	This object control web status.
INT swL2DevCtrlWebTcpPort	1.3.6.1.4.1.171.11.70.9.2.1.2.13.2	INTEGER	read-write	This object can designate tcp port. When web disable this object can't accessible.
swL2DevCtrlTelnet	1.3.6.1.4.1.171.11.70.9.2.1.2.14
INT swL2DevCtrlTelnetState	1.3.6.1.4.1.171.11.70.9.2.1.2.14.1	INTEGER	read-write	This object control telnet status.
INT swL2DevCtrlTelnetTcpPort	1.3.6.1.4.1.171.11.70.9.2.1.2.14.2	INTEGER	read-write	This object can designate tcp port. When telnet disable this object can't accessible.
INT swL2DevCtrlIpAutoconfig	1.3.6.1.4.1.171.11.70.9.2.1.2.15	INTEGER	read-write
INT swL2DevCtrlLedPOEState	1.3.6.1.4.1.171.11.70.9.2.1.2.16	INTEGER	read-write	When set enabled(1), the POE LED is lighten. When set disabled(2), the Link/ACT/Speed LED is lighten.
INT swL2DevCtrlClipagingState	1.3.6.1.4.1.171.11.70.9.2.1.2.17	INTEGER	read-write
INT swL2DevCtrlLLDPState	1.3.6.1.4.1.171.11.70.9.2.1.2.18	INTEGER	read-write	Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For receiving LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
INT swL2DevCtrlLLDPForwardMessageState	1.3.6.1.4.1.171.11.70.9.2.1.2.19	INTEGER	read-write	When lldp is disabled and lldp forward_message's are enabled, the LLDP Data Unit packets received by the switch will be forwarded.
INT swL2DevCtrlVLANTrunkState	1.3.6.1.4.1.171.11.70.9.2.1.2.22	INTEGER	read-write	This indicates the global state of the VLAN trunking feature of the device.
swL2DevAlarm	1.3.6.1.4.1.171.11.70.9.2.1.3
INT swL2DevAlarmNewRoot	1.3.6.1.4.1.171.11.70.9.2.1.3.1	INTEGER	read-write	When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap.
INT swL2DevAlarmTopologyChange	1.3.6.1.4.1.171.11.70.9.2.1.3.2	INTEGER	read-write	This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other.
INT swL2DevAlarmLinkChange	1.3.6.1.4.1.171.11.70.9.2.1.3.3	INTEGER	read-write	This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.
swL2MultiFilter	1.3.6.1.4.1.171.11.70.9.2.2
swL2MultiFilterTable	1.3.6.1.4.1.171.11.70.9.2.2.1		not-accessible	A table that contains infomation about vlan multicast filter mode.
swL2MultiFilterEntry	1.3.6.1.4.1.171.11.70.9.2.2.1.1		not-accessible	A list of multicast filter mode information for each vlan.
INT swL2MultiFilterVid	1.3.6.1.4.1.171.11.70.9.2.2.1.1.1	INTEGER	read-only	vid for each vlan
INT swL2MultiFilterMode	1.3.6.1.4.1.171.11.70.9.2.2.1.1.2	INTEGER	read-write	vlan multicast filter mode.
swL2PortMgmt	1.3.6.1.4.1.171.11.70.9.2.3
swL2PortInfoTable	1.3.6.1.4.1.171.11.70.9.2.3.1		not-accessible	A table that contains information about every port.
swL2PortInfoEntry	1.3.6.1.4.1.171.11.70.9.2.3.1.1		not-accessible	A list of information for each port of the device.
INT swL2PortInfoPortIndex	1.3.6.1.4.1.171.11.70.9.2.3.1.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortInfoMediumType	1.3.6.1.4.1.171.11.70.9.2.3.1.1.2	INTEGER	read-only	Indicates medium type of the port number.
INT swL2PortInfoUnitID	1.3.6.1.4.1.171.11.70.9.2.3.1.1.3	INTEGER	read-only	Indicates ID of the unit in the system
INT swL2PortInfoType	1.3.6.1.4.1.171.11.70.9.2.3.1.1.4	INTEGER	read-only	This object indicates the connector type of this port.
INT swL2PortInfoLinkStatus	1.3.6.1.4.1.171.11.70.9.2.3.1.1.5	INTEGER	read-only	This object indicates the port link status.
INT swL2PortInfoNwayStatus	1.3.6.1.4.1.171.11.70.9.2.3.1.1.6	INTEGER	read-only	This object indicates the port speed and duplex mode.
INT swL2PortInfoErrDisReason	1.3.6.1.4.1.171.11.70.9.2.3.1.1.7	INTEGER	read-only	This object indicates the port if disabled and why error disabled.
swL2PortCtrlTable	1.3.6.1.4.1.171.11.70.9.2.3.2		not-accessible	A table that contains control information about every port.
swL2PortCtrlEntry	1.3.6.1.4.1.171.11.70.9.2.3.2.1		not-accessible	A list of control information for each port of the device.
INT swL2PortCtrlPortIndex	1.3.6.1.4.1.171.11.70.9.2.3.2.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCtrlMediumType	1.3.6.1.4.1.171.11.70.9.2.3.2.1.2	INTEGER	read-only	Indicates medium type of the port number.
INT swL2PortCtrlUnitIndex	1.3.6.1.4.1.171.11.70.9.2.3.2.1.3	INTEGER	read-only	Indicates ID of the unit in the device
INT swL2PortCtrlAdminState	1.3.6.1.4.1.171.11.70.9.2.3.2.1.4	INTEGER	read-write	This object decide the port enabled or disabled.
INT swL2PortCtrlNwayState	1.3.6.1.4.1.171.11.70.9.2.3.2.1.5	INTEGER	read-write	Chose the port speed, duplex mode, and N-Way function mode.
INT swL2PortCtrlFlowCtrlState	1.3.6.1.4.1.171.11.70.9.2.3.2.1.6	INTEGER	read-write	The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
INT swL2PortCtrlLockState	1.3.6.1.4.1.171.11.70.9.2.3.2.1.7	INTEGER	read-write	This object decide the port is locked or not.
INT swL2PortCtrlMACNotifyState	1.3.6.1.4.1.171.11.70.9.2.3.2.1.8	INTEGER	read-write	This object set each port MAC notification state.
INT swL2PortCtrlAutoNegRestart	1.3.6.1.4.1.171.11.70.9.2.3.2.1.11	INTEGER	read-write	If the value of this object is set to restart(1) then this will force auto-negotiation to begin link renegotiation. If auto-negotiation signaling is disabled, a write to this object has no effect. Setting the value of this object to norestart(2) has no effect.
IAN swL2PortCtrlAutoNegCapAdvertisedBits	1.3.6.1.4.1.171.11.70.9.2.3.2.1.12	IANAifMauAutoNegCapBits	read-write	A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in swL2PortAutoNegInfoCapabilityBits cannot be enabled. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC.
INT swL2PortCtrlJumboFrame	1.3.6.1.4.1.171.11.70.9.2.3.3	INTEGER	read-write	This object configure the switch's jumbo frame settings.
I32 swL2PortCtrlJumboFrameMaxSize	1.3.6.1.4.1.171.11.70.9.2.3.4	Integer32	read-only	This object configure the switch's jumbo frame settings.
swL2PortAutoNegInfoTable	1.3.6.1.4.1.171.11.70.9.2.3.8		not-accessible	A table that contains information about every port's auto negotiation status.
swL2PortAutoNegInfoEntry	1.3.6.1.4.1.171.11.70.9.2.3.8.1		not-accessible	A list of information for each port auto negotiation of the device.
INT swL2PortAutoNegInfoPortIndex	1.3.6.1.4.1.171.11.70.9.2.3.8.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortAutoNegInfoAdminStatus	1.3.6.1.4.1.171.11.70.9.2.3.8.1.2	INTEGER	read-only	If the value of this object is disabled(2) then the interface will act as it would if it had no auto-negotiation signaling. The status is affect by setting swL2PortCtrlNwayState.
IAN swL2PortAutoNegInfoCapabilityBits	1.3.6.1.4.1.171.11.70.9.2.3.8.1.3	IANAifMauAutoNegCapBits	read-only	A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. Note that interfaces that support this MIB may have capabilities that extend beyond the scope of this MIB. Note that the local auto-negotiation entity may support some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC.
IAN swL2PortAutoNegInfoCapAdvertisedBits	1.3.6.1.4.1.171.11.70.9.2.3.8.1.4	IANAifMauAutoNegCapBits	read-only	A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in swL2PortAutoNegCapabilityBits cannot be enabled. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC.
IAN swL2PortAutoNegInfoCapReceivedBits	1.3.6.1.4.1.171.11.70.9.2.3.8.1.5	IANAifMauAutoNegCapBits	read-only	A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Note that interfaces that support this MIB may be attached to remote auto-negotiation entities that have capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC.
swL2PortDropCounterTable	1.3.6.1.4.1.171.11.70.9.2.3.9		not-accessible	A table that contains information for each port drop counter.
swL2PortDropCounterEntry	1.3.6.1.4.1.171.11.70.9.2.3.9.1		not-accessible	A list of information for each port auto negotiation of the device.
INT swL2PortDropCounterPortIndex	1.3.6.1.4.1.171.11.70.9.2.3.9.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
CTR swL2PortBufferFullDropsEx	1.3.6.1.4.1.171.11.70.9.2.3.9.1.2	Counter	read-only	The total number of packets discarded while buffer full.
CTR swL2PortACLDrops	1.3.6.1.4.1.171.11.70.9.2.3.9.1.3	Counter	read-only	The total number of packets denied by ACLs.
CTR swL2PortMulticastDrops	1.3.6.1.4.1.171.11.70.9.2.3.9.1.4	Counter	read-only	The total number of multicast packet that is discarded.
CTR swL2PortVLANIngressDrops	1.3.6.1.4.1.171.11.70.9.2.3.9.1.5	Counter	read-only	The total number of packets discarded by VLAN ingress checking.
swL2QOSMgmt	1.3.6.1.4.1.171.11.70.9.2.6
swL2QOSBandwidthControlTable	1.3.6.1.4.1.171.11.70.9.2.6.1		not-accessible	.
swL2QOSBandwidthControlEntry	1.3.6.1.4.1.171.11.70.9.2.6.1.1		not-accessible	A list of information contained in swL2QOSBandwidthControlTable.
INT swL2QOSBandwidthPortIndex	1.3.6.1.4.1.171.11.70.9.2.6.1.1.1	INTEGER	read-only	Indicates the port .
INT swL2QOSBandwidthRxRate	1.3.6.1.4.1.171.11.70.9.2.6.1.1.2	INTEGER	read-write	Indicates RX Rate(1kbit/sec) of the specifed port. Value 10000000 means no limit.
INT swL2QOSBandwidthTxRate	1.3.6.1.4.1.171.11.70.9.2.6.1.1.3	INTEGER	read-write	Indicates TX Rate(1kbit/sec) of the specifed port. Value 10000000 means no limit.
INT swL2QOSBandwidthRadiusRxRate	1.3.6.1.4.1.171.11.70.9.2.6.1.1.4	INTEGER	read-only	The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate.
INT swL2QOSBandwidthRadiusTxRate	1.3.6.1.4.1.171.11.70.9.2.6.1.1.5	INTEGER	read-only	The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate.
swL2QOSSchedulingTable	1.3.6.1.4.1.171.11.70.9.2.6.2		not-accessible	.
swL2QOSSchedulingEntry	1.3.6.1.4.1.171.11.70.9.2.6.2.1		not-accessible	A list of information contained in swL2QOSSchedulingTable.
INT swL2QOSSchedulingPort	1.3.6.1.4.1.171.11.70.9.2.6.2.1.1	INTEGER	read-only	Indicates the port number.
INT swL2QOSSchedulingClassID	1.3.6.1.4.1.171.11.70.9.2.6.2.1.2	INTEGER	read-only	Indicates the hardware queue number.
INT swL2QOSSchedulingMaxPkts	1.3.6.1.4.1.171.11.70.9.2.6.2.1.3	INTEGER	read-write	Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.
INT swL2QOSSchedulingMechanism	1.3.6.1.4.1.171.11.70.9.2.6.2.1.4	INTEGER	read-write	Indicates the mechanism of QOS scheduling.
INT swL2QOSSchedulingMechanismEffec	1.3.6.1.4.1.171.11.70.9.2.6.2.1.5	INTEGER	read-only	Indicates the effective mechanism of QoS scheduling. If the swQoSSchedulingWeight is configured to be 0, then this object will always display strict (1).
swL2QOS8021pUserPriorityTable	1.3.6.1.4.1.171.11.70.9.2.6.3		not-accessible	.
swL2QOS8021pUserPriorityEntry	1.3.6.1.4.1.171.11.70.9.2.6.3.1		not-accessible	A list of information contained in swL2QOS8021pUserPriorityTable.
INT swL2QOS8021pUserPriorityIndex	1.3.6.1.4.1.171.11.70.9.2.6.3.1.1	INTEGER	read-only	The 802.1p user priority .
INT swL2QOS8021pUserPriorityClass	1.3.6.1.4.1.171.11.70.9.2.6.3.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 6 (the highest priority).
swL2QOS8021pDefaultPriorityTable	1.3.6.1.4.1.171.11.70.9.2.6.4		not-accessible	.
swL2QOS8021pDefaultPriorityEntry	1.3.6.1.4.1.171.11.70.9.2.6.4.1		not-accessible	A list of information contained in swL2QOS8021pDefaultPriorityTable.
INT swL2QOS8021pDefaultPriorityIndex	1.3.6.1.4.1.171.11.70.9.2.6.4.1.1	INTEGER	read-only	Indicates the port number .
INT swL2QOS8021pDefaultPriority	1.3.6.1.4.1.171.11.70.9.2.6.4.1.2	INTEGER	read-write	The priority value to assign to untagged packets received by the switch ports on the switch..
INT swL2QOS8021pRadiusPriority	1.3.6.1.4.1.171.11.70.9.2.6.4.1.3	INTEGER	read-only	Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
INT swL2QOSSchedulingMechanismCtrl	1.3.6.1.4.1.171.11.70.9.2.6.5	INTEGER	read-write	This object can control QOS scheduling Mechanism.
INT swL2QOSHolPreventionCtrl	1.3.6.1.4.1.171.11.70.9.2.6.6	INTEGER	read-write	Control QOS Hol Prevention
swCosBandwidthControlTable	1.3.6.1.4.1.171.11.70.9.2.6.7		not-accessible	A table that contains information about CoS Bandwidth Control on each port.
swCosBandwidthControlEntry	1.3.6.1.4.1.171.11.70.9.2.6.7.1		not-accessible	A list that contains CoS Bandwidth Control information for each port.
INT swCosBandwidthPort	1.3.6.1.4.1.171.11.70.9.2.6.7.1.1	INTEGER	read-only	This object indicates the port number.
INT swCosBandwidthClassID	1.3.6.1.4.1.171.11.70.9.2.6.7.1.2	INTEGER	read-only	Indicates the hardware queue number.
INT swCosBandwidthMinRate	1.3.6.1.4.1.171.11.70.9.2.6.7.1.3	INTEGER	read-write	Indicates the Minimum Rate of the specified port. A value of 0 means no limit.
INT swCosBandwidthMaxRate	1.3.6.1.4.1.171.11.70.9.2.6.7.1.4	INTEGER	read-write	Indicates the Maximum Rate of the specified port. A value of 0 means no limit.
swCpuRxRateControlTable	1.3.6.1.4.1.171.11.70.9.2.6.8		not-accessible	A table that contains information about CPU receiving rate control.
swCpuRxRateControlEntry	1.3.6.1.4.1.171.11.70.9.2.6.8.1		not-accessible	A list that contains CPU CoS receiving rate control information.
INT swCpuRxClassID	1.3.6.1.4.1.171.11.70.9.2.6.8.1.1	INTEGER	not-accessible	Indicates the Class of Service ID.
INT swCpuRxRateControlStatus	1.3.6.1.4.1.171.11.70.9.2.6.8.1.2	INTEGER	read-write	Indicates the status of receiving rate control.
swL2PortSecurityMgmt	1.3.6.1.4.1.171.11.70.9.2.7
swL2PortSecurityControlTable	1.3.6.1.4.1.171.11.70.9.2.7.1		not-accessible	port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reach N, any coming packet with not learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
swL2PortSecurityControlEntry	1.3.6.1.4.1.171.11.70.9.2.7.1.1		not-accessible	A list of information contained in swL2PortSecurityControlTable.
INT swL2PortSecurityPortIndex	1.3.6.1.4.1.171.11.70.9.2.7.1.1.1	INTEGER	read-only	Indicates the secured port to lock address learning.
INT swL2PortSecurityMaxLernAddr	1.3.6.1.4.1.171.11.70.9.2.7.1.1.2	INTEGER	read-write	Indicates allowable number of addresses to be learned at this port.
INT swL2PortSecurityMode	1.3.6.1.4.1.171.11.70.9.2.7.1.1.3	INTEGER	read-write	Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In deleteOnReset(4) mode - never age out the locked addresses unless restart the system to prevent from port movement or intrusion.
INT swL2PortSecurityAdmState	1.3.6.1.4.1.171.11.70.9.2.7.1.1.4	INTEGER	read-write	Indicates administration state of locking address.
swL2PortSecurityDelCtrl	1.3.6.1.4.1.171.11.70.9.2.7.2
STR swL2PortSecurityDelVlanName	1.3.6.1.4.1.171.11.70.9.2.7.2.1	DisplayString	read-write	Indicates vlan name.
INT swL2PortSecurityDelPort	1.3.6.1.4.1.171.11.70.9.2.7.2.2	INTEGER	read-write	Indicates the port.0 indicated the function isn't working now.
MAC swL2PortSecurityDelMacAddress	1.3.6.1.4.1.171.11.70.9.2.7.2.3	MacAddress	read-write	Specifies MAC address.
INT swL2PortSecurityDelActivity	1.3.6.1.4.1.171.11.70.9.2.7.2.4	INTEGER	read-write	.
swL2TrunkMgmt	1.3.6.1.4.1.171.11.70.9.2.9
INT swL2TrunkMaxSupportedEntries	1.3.6.1.4.1.171.11.70.9.2.9.1	INTEGER	read-only	Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
INT swL2TrunkCurrentNumEntries	1.3.6.1.4.1.171.11.70.9.2.9.2	INTEGER	read-only	Current actived number of entries in the trunk configuration table.
swL2TrunkCtrlTable	1.3.6.1.4.1.171.11.70.9.2.9.3		not-accessible	This table specifys which ports group a set of ports(up to 8) into a single logical link.
swL2TrunkCtrlEntry	1.3.6.1.4.1.171.11.70.9.2.9.3.1		not-accessible	A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
INT swL2TrunkIndex	1.3.6.1.4.1.171.11.70.9.2.9.3.1.1	INTEGER	read-only	The index of logical port trunk. The trunk group number depend on the existence of unit and module.
INT swL2TrunkMasterPort	1.3.6.1.4.1.171.11.70.9.2.9.3.1.3	INTEGER	read-create	The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
POR swL2TrunkMember	1.3.6.1.4.1.171.11.70.9.2.9.3.1.4	PortList	read-create	Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one trunks.
INT swL2TrunkFloodingPort	1.3.6.1.4.1.171.11.70.9.2.9.3.1.5	INTEGER	read-only	The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.
INT swL2TrunkType	1.3.6.1.4.1.171.11.70.9.2.9.3.1.6	INTEGER	read-create	This object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group .
ROW swL2TrunkState	1.3.6.1.4.1.171.11.70.9.2.9.3.1.7	RowStatus	read-create	This object indicates the status of this entry.
POR swL2TrunkActivePorts	1.3.6.1.4.1.171.11.70.9.2.9.3.1.8	PortList	read-only	The object indicates the active ports of the port trunk entry.
INT swL2TrunkAlgorithm	1.3.6.1.4.1.171.11.70.9.2.9.4	INTEGER	read-write	This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
swL2TrunkLACPPortTable	1.3.6.1.4.1.171.11.70.9.2.9.5		not-accessible	This table specifys which ports group a set of ports(up to 8) into a single logical link.
swL2TrunkLACPPortEntry	1.3.6.1.4.1.171.11.70.9.2.9.5.1		not-accessible	A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
INT swL2TrunkLACPPortIndex	1.3.6.1.4.1.171.11.70.9.2.9.5.1.1	INTEGER	read-only	The index of logical port lacp.
INT swL2TrunkLACPPortState	1.3.6.1.4.1.171.11.70.9.2.9.5.1.2	INTEGER	read-write	The state of logical port lacp.
swL2TrunkVLANTable	1.3.6.1.4.1.171.11.70.9.2.9.6		not-accessible	This table is used to manage the VLAN trunking feature of the device.
swL2TrunkVLANEntry	1.3.6.1.4.1.171.11.70.9.2.9.6.1		not-accessible	This object is used to configure the VLAN trunking settings for each port.
INT swL2TrunkVLANPort	1.3.6.1.4.1.171.11.70.9.2.9.6.1.1	INTEGER	read-only	This object indicates the port being configured.
INT swL2TrunkVLANState	1.3.6.1.4.1.171.11.70.9.2.9.6.1.2	INTEGER	read-write	The state of the logical port LACP.
swL2MirrorMgmt	1.3.6.1.4.1.171.11.70.9.2.10
INT swL2MirrorLogicTargetPort	1.3.6.1.4.1.171.11.70.9.2.10.1	INTEGER	read-write	This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
POR swL2MirrorPortSourceIngress	1.3.6.1.4.1.171.11.70.9.2.10.2	PortList	read-write	The represent the ingress into the source port packet to sniffed.
POR swL2MirrorPortSourceEgress	1.3.6.1.4.1.171.11.70.9.2.10.3	PortList	read-write	The represent the egress from the source port packet to sniffed.
INT swL2MirrorPortState	1.3.6.1.4.1.171.11.70.9.2.10.4	INTEGER	read-write	This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table. enabled(3) - this entry is reside in the table.
swL2MirrorGroupTable	1.3.6.1.4.1.171.11.70.9.2.10.5		not-accessible	This table specifies information about the Mirror group configuration.
swL2MirrorGroupEntry	1.3.6.1.4.1.171.11.70.9.2.10.5.1		not-accessible	A list of information about each Mirror group configuration.
INT swL2MirrorGroupID	1.3.6.1.4.1.171.11.70.9.2.10.5.1.1	INTEGER	not-accessible	This object indicates the mirror group. The range of this object is (1..n), the value of n depends on detail project.
ROW swL2MirrorGroupRowStatus	1.3.6.1.4.1.171.11.70.9.2.10.5.1.2	RowStatus	read-create	This object manages this mirror group entry.
INT swL2MirrorGroupState	1.3.6.1.4.1.171.11.70.9.2.10.5.1.3	INTEGER	read-create	This object indicates the mirror group state.
INT swL2MirrorGroupLogicTargetPort	1.3.6.1.4.1.171.11.70.9.2.10.5.1.4	INTEGER	read-create	This object indicates the mirror group target port.
POR swL2MirrorGroupPortSourceIngress	1.3.6.1.4.1.171.11.70.9.2.10.5.1.5	PortList	read-create	This object indicates the mirror group ingress source ports.
POR swL2MirrorGroupPortSourceEngress	1.3.6.1.4.1.171.11.70.9.2.10.5.1.6	PortList	read-create	This object indicates the mirror group engress source ports.
swL2IGMPMgmt	1.3.6.1.4.1.171.11.70.9.2.11
INT swL2IGMPMaxSupportedVlans	1.3.6.1.4.1.171.11.70.9.2.11.1	INTEGER	read-only	Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPMaxIpGroupNumPerVlan	1.3.6.1.4.1.171.11.70.9.2.11.2	INTEGER	read-only	Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
swL2IGMPCtrlTable	1.3.6.1.4.1.171.11.70.9.2.11.3		not-accessible	The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.
swL2IGMPCtrlEntry	1.3.6.1.4.1.171.11.70.9.2.11.3.1		not-accessible	The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
INT swL2IGMPCtrlVid	1.3.6.1.4.1.171.11.70.9.2.11.3.1.1	INTEGER	read-only	This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
INT swL2IGMPQueryInterval	1.3.6.1.4.1.171.11.70.9.2.11.3.1.2	INTEGER	read-write	The frequency at which IGMP Host-Query packets are transmitted on this switch.
INT swL2IGMPMaxResponseTime	1.3.6.1.4.1.171.11.70.9.2.11.3.1.3	INTEGER	read-write	The maximum query response time on this switch.
INT swL2IGMPRobustness	1.3.6.1.4.1.171.11.70.9.2.11.3.1.4	INTEGER	read-write	The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
INT swL2IGMPLastMemberQueryInterval	1.3.6.1.4.1.171.11.70.9.2.11.3.1.5	INTEGER	read-write	The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
INT swL2IGMPHostTimeout	1.3.6.1.4.1.171.11.70.9.2.11.3.1.6	INTEGER	read-write	The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.
INT swL2IGMPRouteTimeout	1.3.6.1.4.1.171.11.70.9.2.11.3.1.7	INTEGER	read-write	The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
INT swL2IGMPLeaveTimer	1.3.6.1.4.1.171.11.70.9.2.11.3.1.8	INTEGER	read-write	When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
INT swL2IGMPQueryState	1.3.6.1.4.1.171.11.70.9.2.11.3.1.9	INTEGER	read-write	This object decide the IGMP query enabled or disabled.
INT swL2IGMPCurrentState	1.3.6.1.4.1.171.11.70.9.2.11.3.1.10	INTEGER	read-only	This object indicates the current IGMP query state.
INT swL2IGMPCtrlState	1.3.6.1.4.1.171.11.70.9.2.11.3.1.11	INTEGER	read-write	This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry.
INT swL2IGMPFastLeaveState	1.3.6.1.4.1.171.11.70.9.2.11.3.1.12	INTEGER	read-write	This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP fast-leave funtion is disabled for this entry. enable(3) - IGMP fast-leave funtion is enabled for this entry.
INT swL2IGMPQueryVersion	1.3.6.1.4.1.171.11.70.9.2.11.3.1.13	INTEGER	read-write	Configure the IGMP version of query packet which will be sent by the router.
INT swL2IGMPReportSuppression	1.3.6.1.4.1.171.11.70.9.2.11.3.1.15	INTEGER	read-write	When enabled, multiple IGMP reports or leaves for a specific group (S,G) will be integrated into only one report before being sent to the router port.
swL2IGMPQueryInfoTable	1.3.6.1.4.1.171.11.70.9.2.11.4		not-accessible	The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.
swL2IGMPQueryInfoEntry	1.3.6.1.4.1.171.11.70.9.2.11.4.1		not-accessible	Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
INT swL2IGMPInfoVid	1.3.6.1.4.1.171.11.70.9.2.11.4.1.1	INTEGER	read-only	This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPInfoQueryCount	1.3.6.1.4.1.171.11.70.9.2.11.4.1.2	INTEGER	read-only	This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.
INT swL2IGMPInfoTxQueryCount	1.3.6.1.4.1.171.11.70.9.2.11.4.1.3	INTEGER	read-only	This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
swL2IGMPInfoTable	1.3.6.1.4.1.171.11.70.9.2.11.5		not-accessible	The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
swL2IGMPInfoEntry	1.3.6.1.4.1.171.11.70.9.2.11.5.1		not-accessible	Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
INT swL2IGMPVid	1.3.6.1.4.1.171.11.70.9.2.11.5.1.1	INTEGER	read-only	This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
IP swL2IGMPGroupIpAddr	1.3.6.1.4.1.171.11.70.9.2.11.5.1.2	IpAddress	read-only	This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.
MAC swL2IGMPMacAddr	1.3.6.1.4.1.171.11.70.9.2.11.5.1.3	MacAddress	read-only	This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.
POR swL2IGMPPortMap	1.3.6.1.4.1.171.11.70.9.2.11.5.1.4	PortList	read-only	This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.
INT swL2IGMPIpGroupReportCount	1.3.6.1.4.1.171.11.70.9.2.11.5.1.5	INTEGER	read-only	This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.
swL2IGMPRouterPortsTable	1.3.6.1.4.1.171.11.70.9.2.11.6		not-accessible	The table controls the Vlan's IGMP router ports function.
swL2IGMPRouterPortsEntry	1.3.6.1.4.1.171.11.70.9.2.11.6.1		not-accessible	The entry in IGMP router ports table (swL2IGMPRouterPortsTable).
INT swL2IGMPRouterPortsVid	1.3.6.1.4.1.171.11.70.9.2.11.6.1.1	INTEGER	read-only	This object indicates the IGMP router ports entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP ports Table.
POR swL2IGMPRouterStaticPortList	1.3.6.1.4.1.171.11.70.9.2.11.6.1.2	PortList	read-write
POR swL2IGMPRouterDynamicPortList	1.3.6.1.4.1.171.11.70.9.2.11.6.1.3	PortList	read-only
POR swL2IGMPRouterForbiddenPortList	1.3.6.1.4.1.171.11.70.9.2.11.6.1.4	PortList	read-write
swL2IGMPMulticastVlanTable	1.3.6.1.4.1.171.11.70.9.2.11.7		not-accessible	The information of the IGMP snooping multicast vlan table.
swL2IGMPMulticastVlanEntry	1.3.6.1.4.1.171.11.70.9.2.11.7.1		not-accessible	The entry of swL2IGMPMulticastVlanTable.
INT swL2IGMPMulticastVlanid	1.3.6.1.4.1.171.11.70.9.2.11.7.1.1	INTEGER	read-only	This object indicates the vlan id of the IGMP snooping multicast vlan entry.
STR swL2IGMPMulticastVlanName	1.3.6.1.4.1.171.11.70.9.2.11.7.1.2	DisplayString	read-create	This object indicates the vlan name of the IGMP snooping multicast vlan entry.
POR swL2IGMPMulticastVlanSourcePort	1.3.6.1.4.1.171.11.70.9.2.11.7.1.3	PortList	read-create	This object indicate the portlist of the source ports of IGMP snooping multicast vlan. The source ports will be set as tag ports of the vlan entry. And the IGMP control messages received from the member ports would be forwarded to the source ports.
POR swL2IGMPMulticastVlanMemberPort	1.3.6.1.4.1.171.11.70.9.2.11.7.1.4	PortList	read-create	This object indicate the portlist of the member ports of IGMP snooping multicast vlan. The source ports will be set as untag ports of the vlan entry. And the IGMP control messages received from the member ports would be forwarded to the source ports.
IP swL2IGMPMulticastVlanReplaceSourceIP	1.3.6.1.4.1.171.11.70.9.2.11.7.1.5	IpAddress	read-write	The replace source IP of this multicast vlan.
STR swL2IGMPMulticastVlanRangeName	1.3.6.1.4.1.171.11.70.9.2.11.7.1.6	DisplayString	read-write	The name of multicast address range. When read, it shows NULL.
INT swL2IGMPMulticastVlanRangeState	1.3.6.1.4.1.171.11.70.9.2.11.7.1.7	INTEGER	read-write	This object is uesed to add or delete the specified multicast address range. when read it shows none(1); when set add(2) or delete(3),the swL2IGMPMulticastVlanRangeName should not be NULL. When set deleteAll(4), means delete all swL2IGMPMulticastVlanRangeName on this vlan.
INT swL2IGMPMulticastVlanState	1.3.6.1.4.1.171.11.70.9.2.11.7.1.8	INTEGER	read-write	This object can be enabled or disabled IGMP_snooping multicast VLAN.
ROW swL2IGMPMulticastVlanRowStatus	1.3.6.1.4.1.171.11.70.9.2.11.7.1.9	RowStatus	read-create	This object indicates the status of this entry.
POR swL2IGMPMulticastVlanUntagSourcePort	1.3.6.1.4.1.171.11.70.9.2.11.7.1.10	PortList	read-write	This object indicates the untagged member ports to add to the multicast VLAN.
INT swL2IGMPMulticastVlanRemapPriority	1.3.6.1.4.1.171.11.70.9.2.11.7.1.11	INTEGER	read-create	The priority value (0 to 7) to be associated with the data traffic to be forwarded on the multicast VLAN. When set to 8, the packet's original priority will be used.
INT swL2IGMPMulticastVlanReplacePriority	1.3.6.1.4.1.171.11.70.9.2.11.7.1.12	INTEGER	read-create	Specifies that a packet's priority will be changed by the switch based on the remap priority. This flag will only take effect when remap priority is set.
POR swL2IGMPMulticastVlanTagMemberPort	1.3.6.1.4.1.171.11.70.9.2.11.7.1.13	PortList	read-write	This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.
swL2IGMPForwardingTable	1.3.6.1.4.1.171.11.70.9.2.11.8		not-accessible	The table containing current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
swL2IGMPForwardingEntry	1.3.6.1.4.1.171.11.70.9.2.11.8.1		not-accessible	Information about current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
INT swL2IGMPForwardingVid	1.3.6.1.4.1.171.11.70.9.2.11.8.1.1	INTEGER	read-only	This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
IP swL2IGMPForwardingSrcIp	1.3.6.1.4.1.171.11.70.9.2.11.8.1.2	IpAddress	read-only	This object is identify source ip address.
IP swL2IGMPForwardingGroupAddr	1.3.6.1.4.1.171.11.70.9.2.11.8.1.3	IpAddress	read-only	This object is identify group ip address.
POR swL2IGMPForwardingPortMember	1.3.6.1.4.1.171.11.70.9.2.11.8.1.4	PortList	read-only	This object indicates which ports are belong to the same multicast group, in per-Vlan basis.
swL2IGMPMulticastVlanGroupTable	1.3.6.1.4.1.171.11.70.9.2.11.9		not-accessible	The table containing the IGMP snooping multicast VLAN group information
swL2IGMPMulticastVlanGroupEntry	1.3.6.1.4.1.171.11.70.9.2.11.9.1		not-accessible	Information about current IGMP snooping multicast VLAN group.
INT swL2IGMPMulticastVlanGroupVid	1.3.6.1.4.1.171.11.70.9.2.11.9.1.1	INTEGER	read-only	This object indicates the Vid of IGMP snooping multicast VLAN group.
STR swL2IGMPMulticastVlanGroupRangeName	1.3.6.1.4.1.171.11.70.9.2.11.9.1.2	DisplayString	read-only	The name of multicast address range.
IP swL2IGMPMulticastVlanGroupHead	1.3.6.1.4.1.171.11.70.9.2.11.9.1.3	IpAddress	read-only	The head of multicast address range.
IP swL2IGMPMulticastVlanGroupTail	1.3.6.1.4.1.171.11.70.9.2.11.9.1.4	IpAddress	read-only	The tail of multicast address range.
swIGMPSnoopingGroupTable	1.3.6.1.4.1.171.11.70.9.2.11.11		not-accessible	The table contains the current IGMP snooping group information captured by the device.
swIGMPSnoopingGroupEntry	1.3.6.1.4.1.171.11.70.9.2.11.11.1		not-accessible	Information about the current IGMP snooping group information which has been captured by the device.
INT swIGMPSnoopingGroupVid	1.3.6.1.4.1.171.11.70.9.2.11.11.1.1	INTEGER	read-only	This object indicates the VID of the individual IGMP snooping group table entry.
IP swIGMPSnoopingGroupGroupAddr	1.3.6.1.4.1.171.11.70.9.2.11.11.1.2	IpAddress	read-only	This object identifies the group IP address which have been captured from the IGMP packet, on a per-VLAN basis.
IP swIGMPSnoopingGroupSourceAddr	1.3.6.1.4.1.171.11.70.9.2.11.11.1.3	IpAddress	read-only	This object identifies the source addresses.
POR swIGMPSnoopingGroupIncludePortMap	1.3.6.1.4.1.171.11.70.9.2.11.11.1.4	PortList	read-only	This object indicates the port list under INCLUDE mode.
POR swIGMPSnoopingGroupExcludePortMap	1.3.6.1.4.1.171.11.70.9.2.11.11.1.5	PortList	read-only	This object indicates the port list under EXCLUDE mode.
swL2IGMPSnoopingStaticGroupTable	1.3.6.1.4.1.171.11.70.9.2.11.16		not-accessible	The table contains the current IGMP snooping static group information captured by the device.
swL2IGMPSnoopingStaticGroupEntry	1.3.6.1.4.1.171.11.70.9.2.11.16.1		not-accessible	Information about current IGMP snooping static group information captured by the device.
INT swL2IGMPSnoopingStaticGroupVID	1.3.6.1.4.1.171.11.70.9.2.11.16.1.1	INTEGER	read-only	This object indicates the VID of the current IGMP snooping static group.
IP swL2IGMPSnoopingStaticGroupIPaddress	1.3.6.1.4.1.171.11.70.9.2.11.16.1.2	IpAddress	read-only	This object indicates the current IGMP snooping static group IP address.
POR swL2IGMPSnoopingStaticGroupMemberPortList	1.3.6.1.4.1.171.11.70.9.2.11.16.1.3	PortList	read-write	This object indicates the current IGMP snooping static group Member Portlist.
ROW swL2IGMPSnoopingStaticGroupRowStatus	1.3.6.1.4.1.171.11.70.9.2.11.16.1.4	RowStatus	read-create	This object indicates the status of this entry.
swL2TrafficSegMgmt	1.3.6.1.4.1.171.11.70.9.2.14
swL2TrafficSegTable	1.3.6.1.4.1.171.11.70.9.2.14.1		not-accessible	This table specifys the port just can forward traffic to the specific port list.
swL2TrafficSegEntry	1.3.6.1.4.1.171.11.70.9.2.14.1.1		not-accessible	A list of information specifies the port with its traffic forward list.
INT swL2TrafficSegPort	1.3.6.1.4.1.171.11.70.9.2.14.1.1.1	INTEGER	read-only	The port number of the logical port.
POR swL2TrafficSegForwardPorts	1.3.6.1.4.1.171.11.70.9.2.14.1.1.2	PortList	read-write	The port list that the specific port can forward traffic.
swL2IpLimitedMulticastMgmt	1.3.6.1.4.1.171.11.70.9.2.15
swL2IpLimitedMulticastTable	1.3.6.1.4.1.171.11.70.9.2.15.1		not-accessible	This entity's per-port Limited IP multicast address range table.
swL2IpLimitedMulticastEntry	1.3.6.1.4.1.171.11.70.9.2.15.1.1		not-accessible	A particular route to a particular destination, under a particular policy. Once an entry be built,it shouldn't be modified.That is,it just support create and delete action.
INT swL2IpLimitedMulticastPortIndex	1.3.6.1.4.1.171.11.70.9.2.15.1.1.1	INTEGER	read-only	A port to config the limited multicast address.
IP swL2IpLimitedMulticastHead	1.3.6.1.4.1.171.11.70.9.2.15.1.1.2	IpAddress	not-accessible	The head of multicast address range.
IP swL2IpLimitedMulticastTail	1.3.6.1.4.1.171.11.70.9.2.15.1.1.3	IpAddress	not-accessible	The tail of multicast address range.
INT swL2IpLimitedMulticastAccess	1.3.6.1.4.1.171.11.70.9.2.15.1.1.4	INTEGER	read-write	It allow you to permit or deny multicast range.
INT swL2IpLimitedMulticastState	1.3.6.1.4.1.171.11.70.9.2.15.1.1.5	INTEGER	read-write	Enable or disable limited multicast address for the chosen port.
INT swL2IpLimitedMulticastDelState	1.3.6.1.4.1.171.11.70.9.2.15.1.1.6	INTEGER	not-accessible	Enable or disable delete limited multicast address for the chosen port.
STR swL2IpLimitedMulticastRangeName	1.3.6.1.4.1.171.11.70.9.2.15.1.1.7	DisplayString	read-write	The name of multicast address range. When read, it shows NULL.
INT swL2IpLimitedMulticastRangeNameState	1.3.6.1.4.1.171.11.70.9.2.15.1.1.8	INTEGER	read-write	Add or delete the specified multicast address range. When read, it shows other(1); When set add(2) or delete(3), the swL2IpLimitedMulticastRangeName should be set also, and it should not be NULL. When set deleteAll(4), means delete all swL2IpLimitedMulticastRangeName on this port. And the set multicast range name value could be gotten in swL2LimitedMulticastAddressTable.
swL2LimitedMulticastAddressTable	1.3.6.1.4.1.171.11.70.9.2.15.2		not-accessible	A table contains the limited multicast address information.
swL2LimitedMulticastAddressEntry	1.3.6.1.4.1.171.11.70.9.2.15.2.1		not-accessible	The information of limited multicast address.
INT swL2LimitedMulticastAddressPort	1.3.6.1.4.1.171.11.70.9.2.15.2.1.1	INTEGER	read-only	The port index.
STR swL2LimitedMulticastAddressRangeName	1.3.6.1.4.1.171.11.70.9.2.15.2.1.2	DisplayString	read-only	The name of multicast address range.
IP swL2LimitedMulticastAddressHead	1.3.6.1.4.1.171.11.70.9.2.15.2.1.3	IpAddress	read-only	The head of multicast address range.
IP swL2LimitedMulticastAddressTail	1.3.6.1.4.1.171.11.70.9.2.15.2.1.4	IpAddress	read-only	The tail of multicast address range.
swL2MgmtMIBTraps	1.3.6.1.4.1.171.11.70.9.2.16
swL2Notify	1.3.6.1.4.1.171.11.70.9.2.16.1
swL2NotifyPrefix	1.3.6.1.4.1.171.11.70.9.2.16.1.2
swL2NotifFirmware	1.3.6.1.4.1.171.11.70.9.2.16.1.2.0
NTF swL2macNotification	1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.1			This trap indicates the mac addresses variation in address table .
NTF swL2PortLoopOccurred	1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.3			The trap is sent when Port loop occurred.
NTF swL2PortLoopRestart	1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.4			The trap is sent when Port loop restart after interval time.
NTF swL2VlanLoopOccurred	1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.5			The trap is sent when Port with VID loop occurred.
NTF swL2VlanLoopRestart	1.3.6.1.4.1.171.11.70.9.2.16.1.2.0.6			The trap is sent when Port with VID loop restart after interval time.
swl2NotificationBidings	1.3.6.1.4.1.171.11.70.9.2.16.1.2.1
OCT swL2macNotifyInfo	1.3.6.1.4.1.171.11.70.9.2.16.1.2.1.1	OCTET STRING	read-only	This object indicates the last time reboot information.
INT swL2VlanLoopDetectVID	1.3.6.1.4.1.171.11.70.9.2.16.1.2.1.3	INTEGER	accessible-for-notify	This object indicates the VID that has detected a loopback.
swL2VlanMgmt	1.3.6.1.4.1.171.11.70.9.2.17
swL2VlanTable	1.3.6.1.4.1.171.11.70.9.2.17.1		not-accessible	A table containing current configuration information for each VLAN currently configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
swL2VlanEntry	1.3.6.1.4.1.171.11.70.9.2.17.1.1		not-accessible	Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
VLA swL2VlanIndex	1.3.6.1.4.1.171.11.70.9.2.17.1.1.1	VlanId	not-accessible	The VLAN ID of the VLAN to be created. The range is 1 - 4094.
STR swL2VlanName	1.3.6.1.4.1.171.11.70.9.2.17.1.1.2	DisplayString	read-only	The name of the VLAN to be displayed.
INT swL2VlanType	1.3.6.1.4.1.171.11.70.9.2.17.1.1.3	INTEGER	read-only	The type of the VLAN to be displayed.
POR swL2VlanMemberPorts	1.3.6.1.4.1.171.11.70.9.2.17.1.1.4	PortList	read-only	A range of member ports to the VLAN.
POR swL2VlanStaticPorts	1.3.6.1.4.1.171.11.70.9.2.17.1.1.5	PortList	read-only	A range of static ports to the VLAN.
POR swL2VlanStaticTaggedPorts	1.3.6.1.4.1.171.11.70.9.2.17.1.1.6	PortList	read-only	Specifies the additional ports as tagged.
POR swL2VlanStaticUntaggedPorts	1.3.6.1.4.1.171.11.70.9.2.17.1.1.7	PortList	read-only	Specifies the additional ports as untagged.
POR swL2VlanForbiddenPorts	1.3.6.1.4.1.171.11.70.9.2.17.1.1.8	PortList	read-only	The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanStaticEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set.
POR swL2VlanCurrentTaggedPorts	1.3.6.1.4.1.171.11.70.9.2.17.1.1.9	PortList	read-only	The set of ports which are transmitting traffic for this VLAN as tagged frames.
POR swL2VlanCurrentUntaggedPorts	1.3.6.1.4.1.171.11.70.9.2.17.1.1.10	PortList	read-only	The set of ports which are transmitting traffic for this VLAN as untagged frames.
INT swL2VlanAdvertisementState	1.3.6.1.4.1.171.11.70.9.2.17.1.1.11	INTEGER	read-write	Specifies the VLAN as able to join GVRP If this parameter is not set, the VLAN cannot be configured to have forbidden ports. This flag protocol VLAN is fixed to DISABLE.
INT swL2PVIDAutoAssignmentState	1.3.6.1.4.1.171.11.70.9.2.17.2	INTEGER	read-write	This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change PVID. If 'Auto-assign PVID' is enabled, PVID will be possibly changed by PVID or VLAN configuration. When user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. In the form of VLAN list command, PVID is updated with last item of VLAN list. When user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned with 'default VLAN'.
swL2dot1vProtocolMgmt	1.3.6.1.4.1.171.11.70.9.2.18
swL2dot1vProtocolGroupTable	1.3.6.1.4.1.171.11.70.9.2.18.1		not-accessible	A table that contains mappings from Protocol Templates to Protocol Group Identifiers used for Port-and-Protocol-based VLAN Classification.
swL2dot1vProtocolGroupEntry	1.3.6.1.4.1.171.11.70.9.2.18.1.1		not-accessible	A mapping from a Protocol Template to a Protocol Group Identifier.
INT swL2dot1vProtocolTemplateFrameType	1.3.6.1.4.1.171.11.70.9.2.18.1.1.1	INTEGER	read-only	The data-link encapsulation format or the 'detagged_frame_type' in a Protocol Template.
OCT swL2dot1vProtocolTemplateProtocolValue	1.3.6.1.4.1.171.11.70.9.2.18.1.1.2	OCTET STRING	read-only	The identification of the protocol above the data-link layer in a Protocol Template. Depending on the frame type, the octet string will have one of the following values: For 'ethernet', 'rfc1042' and 'snap8021H', this is the 16-bit (2-octet) IEEE 802.3 Type Field. For 'llcOther', this is the 2-octet IEEE 802.2 Link Service Access Point (LSAP) pair: first octet for Destination Service Access Point (DSAP) and second octet for Source Service Access Point (SSAP).
I32 swL2dot1vProtocolGroupId	1.3.6.1.4.1.171.11.70.9.2.18.1.1.3	Integer32	read-create	Represents a group of protocols that are associated together when assigning a VID to a frame.
ROW swL2dot1vProtocolGroupRowStatus	1.3.6.1.4.1.171.11.70.9.2.18.1.1.4	RowStatus	read-create	This object indicates the status of this entry.
swL2dot1vProtocolPortTable	1.3.6.1.4.1.171.11.70.9.2.18.2		not-accessible	A table that contains VID sets used for Port-and-Protocol-based VLAN Classification.
swL2dot1vProtocolPortEntry	1.3.6.1.4.1.171.11.70.9.2.18.2.1		not-accessible	A VID set for a port.
I32 swL2dot1vProtocolPort	1.3.6.1.4.1.171.11.70.9.2.18.2.1.1	Integer32	read-only	The port number of the port.
I32 swL2dot1vProtocolPortGroupId	1.3.6.1.4.1.171.11.70.9.2.18.2.1.2	Integer32	read-only	Designates a group of protocols in the Protocol Group Database.
I32 swL2dot1vProtocolPortGroupVid	1.3.6.1.4.1.171.11.70.9.2.18.2.1.3	Integer32	read-write	The VID associated with a group of protocols for each port.
ROW swL2dot1vProtocolPortRowStatus	1.3.6.1.4.1.171.11.70.9.2.18.2.1.5	RowStatus	read-create	This object indicates the status of this entry.
swL2MulticastRangeMgmt	1.3.6.1.4.1.171.11.70.9.2.19
swL2MulticastRangeTable	1.3.6.1.4.1.171.11.70.9.2.19.1		not-accessible	A table contains multicast address range information.
swL2MulticastRangeEntry	1.3.6.1.4.1.171.11.70.9.2.19.1.1		not-accessible	Information about multicast address range.
STR swL2MulticastRangeName	1.3.6.1.4.1.171.11.70.9.2.19.1.1.1	DisplayString	read-only	The name of multicast address range.
IP swL2MulticastRangeHead	1.3.6.1.4.1.171.11.70.9.2.19.1.1.2	IpAddress	read-create	The head of multicast address range.
IP swL2MulticastRangeTail	1.3.6.1.4.1.171.11.70.9.2.19.1.1.3	IpAddress	read-create	The tail of multicast address range.
ROW swL2MulticastRangeState	1.3.6.1.4.1.171.11.70.9.2.19.1.1.4	RowStatus	read-create	This object indicates the status of this entry.
swL2LoopDetectMgmt	1.3.6.1.4.1.171.11.70.9.2.20
swL2LoopDetectCtrl	1.3.6.1.4.1.171.11.70.9.2.20.1
INT swL2LoopDetectAdminState	1.3.6.1.4.1.171.11.70.9.2.20.1.1	INTEGER	read-write	This object indicates the loopback detection status for the system.
INT swL2LoopDetectInterval	1.3.6.1.4.1.171.11.70.9.2.20.1.2	INTEGER	read-write	This object indicates the interval value, the range is from 1 to 32767 seconds.
INT swL2LoopDetectRecoverTime	1.3.6.1.4.1.171.11.70.9.2.20.1.3	INTEGER	read-write	This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
INT swL2LoopDetectMode	1.3.6.1.4.1.171.11.70.9.2.20.1.4	INTEGER	read-write	This object indicates the loopback detection mode for the system.
INT swL2LoopDetectTrapMode	1.3.6.1.4.1.171.11.70.9.2.20.1.5	INTEGER	read-write	This object indicates the loopback detection trap mode for the system.
swL2LoopDetectPortMgmt	1.3.6.1.4.1.171.11.70.9.2.20.2
swL2LoopDetectPortTable	1.3.6.1.4.1.171.11.70.9.2.20.2.1		not-accessible	The table specifies the loopback detection function specified by port.
swL2LoopDetectPortEntry	1.3.6.1.4.1.171.11.70.9.2.20.2.1.1		not-accessible	The table specifies the loopback detection function specified by port.
INT swL2LoopDetectPortIndex	1.3.6.1.4.1.171.11.70.9.2.20.2.1.1.1	INTEGER	read-only	This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
INT swL2LoopDetectPortState	1.3.6.1.4.1.171.11.70.9.2.20.2.1.1.2	INTEGER	read-write	This object indicates the loopback detection function state on the port.
STR swL2LoopDetectPortLoopVLAN	1.3.6.1.4.1.171.11.70.9.2.20.2.1.1.3	DisplayString	read-only	This object indicates the VLAN list that has detected a loopback.
INT swL2LoopDetectPortLoopStatus	1.3.6.1.4.1.171.11.70.9.2.20.2.1.1.4	INTEGER	read-only	This object indicates the port status.
swL2DhcpLocalRelayMgmt	1.3.6.1.4.1.171.11.70.9.2.24
INT swL2DhcpLocalRelayState	1.3.6.1.4.1.171.11.70.9.2.24.1	INTEGER	read-write	This object indicates the status of the DHCP local relay function of the switch.
swL2DhcpLocalRelayVLANTable	1.3.6.1.4.1.171.11.70.9.2.24.2		not-accessible	This table is used to manage the DHCP local relay status for each VLAN.
swL2DhcpLocalRelayVLANEntry	1.3.6.1.4.1.171.11.70.9.2.24.2.1		not-accessible	This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
INT swL2DhcpLocalRelayVLANID	1.3.6.1.4.1.171.11.70.9.2.24.2.1.1	INTEGER	read-only	This object shows the VIDs of the current VLANS in the switch.
INT swL2DhcpLocalRelayVLANState	1.3.6.1.4.1.171.11.70.9.2.24.2.1.2	INTEGER	read-write	This object indicates the status of the DHCP relay function of the VLAN.

RFC description

Layer 2 management for D-Link DGS3612G switch including VLANs, port management, QoS, and security.

Start monitoring D-Link DGS-3612G Gigabit Ethernet switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DGS3612G-L2MGMT-MIB