All MIBs › DF10-DCB-MIB
Organization: Dell Inc.
Last Updated: 2012-04-16
Category: Quality of Service
Description: Manages Data Center Bridging (DCB) configuration and priority flow control for DF10 equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is DF10-DCB-MIB?
DF10-DCB-MIB is Dell's proprietary extension MIB for Dell Networking OS (Force10-derived) switches, managing Data Center Bridging (DCB) and DCBX (DCB Exchange) features such as Priority-based Flow Control (PFC) and Enhanced Transmission Selection (ETS) used in converged/lossless Ethernet fabrics (e.g., for FCoE or iSCSI traffic). It exposes configuration objects for DCB applications, DCBX negotiation, and ETS bandwidth/priority group settings, along with notification objects for DCB-related events. Its role in monitoring is chiefly software/protocol status: DCBX negotiation state and application priority mappings must be correctly matched between switch and end-host/adapter to avoid lossless-traffic disruptions, and notifications flag misconfigurations or negotiation failures. It's explicitly an extension to the standard Dell Networking OS management framework, complementing IEEE DCB standards (802.1Qbb PFC, 802.1Qaz ETS/DCBX). It's typically deployed on Dell/Force10 data center switches supporting converged Ethernet fabrics carrying storage and LAN traffic together, and administrators can download the DF10-DCB-MIB file to load it directly into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in DF10-DCB-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Dell Networking (Force10) data center switch
Monitoring Examples
An admin would poll dF10DcbApplicationObjects to confirm the priority-to-application (e.g., FCoE, iSCSI) mapping matches expectations on a given switch port, and check dF10DCBXObjects to verify DCBX negotiation with an attached converged network adapter completed successfully rather than falling back to defaults. Monitoring dF10ETSObjects reveals whether bandwidth allocation across traffic classes (ETS priority groups) matches the configured policy, and a mismatch here could starve storage traffic of guaranteed bandwidth. dF10DcbNotificationObjects would be watched for DCBX peer change or configuration-mismatch traps indicating a cabling or adapter configuration issue.
What Can Be Monitored
- DCBX negotiation state
- priority flow control (PFC) configuration
- ETS bandwidth/priority group allocation
- application-to-priority mapping
- DCB configuration change notifications
This MIB depends on
Related MIBs
Imported Objects
From FORCE10-SMI
| f10Mgmt | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using dF10DCBXPortMultiplePeerCount OID:
Select a Dell Networking (Force10) data center switch (DCB/DCBX) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type dF10DCBXPortMultiplePeerCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Indicates number of times multiple peers were detected. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| dF10Dcb | 1.3.6.1.4.1.6027.3.15 | The proprietary extension MIB module for Dell Networking OS DCB and DCBX. | ||
| dF10DcbApplicationObjects | 1.3.6.1.4.1.6027.3.15.3 | |||
| ENA dF10DcbETSAdminStatus | 1.3.6.1.4.1.6027.3.15.2.1.1.2 | EnabledStatus | read-only | This object is used to display if ETS feature is enabled or disabled on the given port. |
| U32 dF10DcbMaxPfcProfiles | 1.3.6.1.4.1.6027.3.15.1.3 | Unsigned32 | read-only | The maximum number of PFC(Priority Based Flow Control)profiles supported by the device. A PFC profile is a bitmap, containing the status of PFC for all the priorities. If Bit 0 is set, then it means PFC is enabled for priority 0, otherwise PFC is disabled for priority 0. If Bit 1 is set, then it means PFC is enabled for priority 1, otherwise PFC is disabled for priority 1, and so on. If this object value is zero, it means all the bits are set to zero and PFC is disabled for all priorities. If this object's value is 3, it means the bits 0 and 1 are set and PFC is enabled for priorities 0 and 1 and disabled for all other priorities. Device supporting 256 PFC profiles, means all possible combination of PFC status on 8 priorities are supported. |
| dF10DCBMibCompliance | 1.3.6.1.4.1.6027.3.15.5.1.2 | The compliance statement for Dell Networking OS product which implement the Dell Networking OS dcb MIB. This module consists of the obsolete MIB objects. | ||
| dF10DCBMibComplianceRev1 | 1.3.6.1.4.1.6027.3.15.5.1.1 | The compliance statement for Dell Networking OS product which implement the Dell Networking OS dcbx MIB. | ||
| dF10DCBMibCompliances | 1.3.6.1.4.1.6027.3.15.5.1 | |||
| dF10DCBMibConformance | 1.3.6.1.4.1.6027.3.15.5 | |||
| dF10DCBMibGroups | 1.3.6.1.4.1.6027.3.15.5.2 | |||
| dF10DcbNotificationObjects | 1.3.6.1.4.1.6027.3.15.4 | |||
| dF10DCBNotificationObjectsGroup | 1.3.6.1.4.1.6027.3.15.5.2.9 | This object group represents the collection of objects used by the notification group dF10DCBNotificationsGroup. | ||
| dF10DCBNotificationsGroup | 1.3.6.1.4.1.6027.3.15.5.2.10 | A collection on notification objects in the DF10-DCB mib | ||
| dF10DcbObjectGroup | 1.3.6.1.4.1.6027.3.15.5.2.2 | This group represents a collection of objects providing the information on the DCB control parameters for a particular port. | ||
| dF10DcbObjects | 1.3.6.1.4.1.6027.3.15.2 | |||
| T/F dF10DcbPeerUpStatus | 1.3.6.1.4.1.6027.3.15.4.1.2 | TruthValue | accessible-for-notify | This object refers to the DCBX Peer Up or Peer down status on the port. If the value is 'true', then the DCBX Peer will be present and UP. If the value is 'false', then the DCBX Peer will be absent and DOWN. |
| ENA dF10DcbPFCAdminStatus | 1.3.6.1.4.1.6027.3.15.2.1.1.3 | EnabledStatus | read-only | This object is used to display if PFC feature is enabled or disabled on the given port. |
| U32 dF10DcbPfcMaxThreshold | 1.3.6.1.4.1.6027.3.15.1.2 | Unsigned32 | read-only | The maximum PFC(Priority Based Flow Control)threshold for the switch. This Object indicates the maximum Receive queue buffer count. The minimum and maximum values for this object may vary based on the underlying hardware's capacity. |
| U32 dF10DcbPfcMinThreshold | 1.3.6.1.4.1.6027.3.15.1.1 | Unsigned32 | read-only | The minimum PFC(Priority Based Flow Control) threshold for the switch. This Object indicates the minimum Receive queue buffer count. The minimum and maximum values for this object may vary based on the underlying hardware's capacity. |
| dF10DcbPortEntry | 1.3.6.1.4.1.6027.3.15.2.1.1 | not-accessible | An entry containing DCB control parameters for a particular port. | |
| NUM dF10DcbPortNumber | 1.3.6.1.4.1.6027.3.15.2.1.1.1 | InterfaceIndex | not-accessible | This indicates the interface identifier for which the Dcb configuration is applied. |
| dF10DcbPortTable | 1.3.6.1.4.1.6027.3.15.2.1 | not-accessible | Port table contains the DCB features (Enhanced Transmission Selection/Priortiy Based Flow Control) status (enabled or disabled). | |
| dF10DcbSystem | 1.3.6.1.4.1.6027.3.15.1 | |||
| dF10DcbSystemObjectGroup | 1.3.6.1.4.1.6027.3.15.5.2.1 | This group represents a collection of objects providing the DCB system information. | ||
| dF10DCBTrapObjects | 1.3.6.1.4.1.6027.3.15.4.1 | |||
| T/F dF10DcbTrapPortNumber | 1.3.6.1.4.1.6027.3.15.4.1.1 | TruthValue | accessible-for-notify | This object refers to the Port number for which the DCBX feature is enabled. And will be used in sending the feature port specific Traps. |
| dF10DCBTraps | 1.3.6.1.4.1.6027.3.15.4.0 | |||
| ENA dF10DCBXAdminStatus | 1.3.6.1.4.1.6027.3.15.3.1.2.1.2 | EnabledStatus | read-only | This object is used to display if DCBX feature is enabled(1) or disabled(2) on the given port. |
| DCB dF10DCBXAutoCfgPortRole | 1.3.6.1.4.1.6027.3.15.3.1.2.1.3 | DcbxPortRole | read-write | Ports operating in the manual role do not have their configuration affected by peer devices or by internal propagation of configuration. These ports will advertise their configuration to their peer if DCBX is enabled on that port. Auto-up: Advertises a configuration, but is also willing to accept a configuration from the link-partner and propagate it internally to the auto-downstream ports as well as receive configuration propagated internally by other auto-upstream ports. Auto-down: Advertises a configuration but is not willing to accept one from the link partner. However, the port will accept a configuration propagated internally by the configuration source. Configuration Source:In this role, the port has been manually selected to be the configuration source. Configuration received over this port is propagated to the other auto-configuration ports. |
| I32 dF10DcbxGlobalTraceLevel | 1.3.6.1.4.1.6027.3.15.3.1.1.1 | Integer32 | read-write | This object is used to enable Trace Statements in DCBX Module. A FOUR BYTE integer is used for enabling the level of tracing. Each BIT in the four byte integer represents a particular level of Trace. The mapping between the bit positions & the level of trace is as follows: 1 - Management Traces 2 - DCBX State Machine Traces 3 - TLV Traces 4 - System Resource Traces 5 - Failure Traces 6 - Configuration Exchange Traces 7 - Auto Detection Traces The remaining bits are unused. The user has to enter the corresponding INTEGER VALUE for the trace to be set. Only one trace can be enabled at a time. To enable all the traces, sum of all individual traces must be provided. |
| DCB dF10DCBXGlobalVersion | 1.3.6.1.4.1.6027.3.15.3.1.1.2 | DcbxVersion | read-write | CIN is Cisco Intel Nuova DCBX (version 1.0). CEE is converged enhanced ethernet DCBX (version 1.06). IEEE is 802-1 az version. The default value is auto. DCBX supports the legacy implementations v1.0 (CIN) and v1.06 (CEE) in addition to standard IEEE version 2.4 DCBX. 1.DCBX starts in standard IEEE mode by sending an IEEE standard version 2.4 DCBX frame. If the peer responds, then IEEE standard version 2.4 DCBX is used,Starts means after a link up, a DCBX timeout (or multiple peer condition) or when commanded by the network operator. If DCBX receives a DCBX frame with an OUI indicating a legacy version, it immediately switches into legacy mode for the detected version and does not wait for the 3x LLDP fast timeout. 2.If no IEEE DCBX response is received within 3 times the LLDP fast transmit timeout period, DCBX immediately transmits a version 1.06 DCBX frame with the appropriate version number. If DCBX receives a DCBX frame with an OUI indicating IEEE standard support, it immediately switches into IEEE standard mode and does not wait for the timer. If DCBX receives a DCBX frame with an OUI indicating legacy mode and a version number indicating version 1.0 support, it immediately switches into legacy 1.0 mode and does not wait for the timer. 3.If no version 1.06 response is received within 3 times the DCBX fast transmit timeout period, DCBX falls back to version 1.0 and immediately transmits a version 1.0 frame. If no response is received within 3 times the DCBX fast transmit period, DCBX waits the standard LLDP timeout period, and then begins again with step 1. If DCBX receives a DCBX frame with an OUI indicating IEEE standard mode, it immediately switches into IEEE standard mode. |
| dF10DCBXObjects | 1.3.6.1.4.1.6027.3.15.3.1 | |||
| ENA dF10DCBXOperStatus | 1.3.6.1.4.1.6027.3.15.3.1.3.1.5 | EnabledStatus | read-only | This object gives information on the operational status of DCBX on the given port. Enabled(1) indicates DCBX on the port is in sync with the remote and is operationally up. Disabled(2) indicates DCBX on the port is operationally disabled. |
| U32 dF10DCBXPortAckNum | 1.3.6.1.4.1.6027.3.15.3.1.3.1.11 | Unsigned32 | read-only | Specifies the current ACK number that is to be sent to peer in DCBX control TLVs in CEE/CIN Mode. |
| INT dF10DCBXPortCfgSource | 1.3.6.1.4.1.6027.3.15.3.1.3.1.4 | INTEGER | read-only | Indicates if this port is the source of configuration information for auto-* ports. |
| BIT dF10DCBXPortConfigTLVsTxEnable | 1.3.6.1.4.1.6027.3.15.3.1.2.1.6 | Bits | read-write | Bitmap that includes the DCBX defined set of LLDP TLVs whose transmission is enabled on the local LLDP agent by network management. Having the bit 'pfc(0)' set indicates that the LLDP transmit PFC TLV as part of DCBX TLVs. Having the bit 'etsConfig(1)' set indicates that the LLDP transmit ETS configuration TLV as part of DCBX TLVs. Having the bit 'etsRecom(2)' set indicates that transmit ETS Recommendation TLV as part of DCBX TLVs. Having the bit 'applicationPriorityFCOE(3)' set indicates that the LLDP transmit applicationPriority TLV for FCOE as part of DCBX TLVs. Having the bit 'applicationPriorityISCSI(4)' set indicates that the LLDP transmit applicationPriority TLV for ISCSI as part of DCBX TLVs. |
| dF10DCBXPortEntry | 1.3.6.1.4.1.6027.3.15.3.1.2.1 | not-accessible | An entry containing DCBX control parameters for a particular port. | |
| C32 dF10DCBXPortErrorFramesCount | 1.3.6.1.4.1.6027.3.15.3.1.3.1.15 | Counter32 | read-only | The number of DCBX frames discarded due to errors in the frame. |
| C32 dF10DCBXPortMultiplePeerCountEx | 1.3.6.1.4.1.6027.3.15.3.1.3.1.6 | Counter32 | read-only | Indicates number of times multiple peers were detected. A duplicate peer is when more than one DCBX peer is detected on a port. |
| NUM dF10DCBXPortNumber | 1.3.6.1.4.1.6027.3.15.3.1.2.1.1 | InterfaceIndex | not-accessible | This indicates the interface identifier for which the DCBX configuration is applied. |
| DCB dF10DCBXPortOperVersion | 1.3.6.1.4.1.6027.3.15.3.1.3.1.2 | DcbxVersion | read-only | Specifies the DCBX mode in which the interface is currently operating. |
| MAC dF10DCBXPortPeerMACaddress | 1.3.6.1.4.1.6027.3.15.3.1.3.1.3 | MacAddress | read-only | MAC Address of the DCBX peer. |
| U32 dF10DCBXPortPeerMaxVersion | 1.3.6.1.4.1.6027.3.15.3.1.3.1.9 | Unsigned32 | read-only | Specifies the max version of the peer DCBX device. Valid only when peer device is CEE/CIN DCBX device. |
| U32 dF10DCBXPortPeerOperVersionNum | 1.3.6.1.4.1.6027.3.15.3.1.3.1.8 | Unsigned32 | read-only | Specifies the operational version of the peer DCBX device. Valid only when peer device is a CEE/CIN DCBX device. |
| U32 dF10DCBXPortPeerRcvdAckNum | 1.3.6.1.4.1.6027.3.15.3.1.3.1.12 | Unsigned32 | read-only | Specifies the current ACK number that is sent by peer in DCBX control TLV in CEE/CIN Mode. |
| C32 dF10DCBXPortPeerRemovedCount | 1.3.6.1.4.1.6027.3.15.3.1.3.1.7 | Counter32 | read-only | . |
| C32 dF10DCBXPortRxCount | 1.3.6.1.4.1.6027.3.15.3.1.3.1.14 | Counter32 | read-only | The number of DCBX frames received per interface. |
| U32 dF10DCBXPortSeqNum | 1.3.6.1.4.1.6027.3.15.3.1.3.1.10 | Unsigned32 | read-only | Specifies the current sequence number that is sent in DCBX control TLVs in CEE/CIN Mode. |
| dF10DCBXPortStatusEntry | 1.3.6.1.4.1.6027.3.15.3.1.3.1 | not-accessible | . | |
| dF10DCBXPortStatusTable | 1.3.6.1.4.1.6027.3.15.3.1.3 | not-accessible | . | |
| BIT dF10DCBXPortSupportedTLVs | 1.3.6.1.4.1.6027.3.15.3.1.2.1.5 | Bits | read-only | Bitmap that includes the supported set of DCBX LLDP TLVs the device is capable of and whose transmission is allowed on the local LLDP agent by network management. Having the bit 'pfc(0)' set indicates that the LLDP transmit PFC TLV as part of DCBX TLVs. Having the bit 'etcConfig(1)' set indicates that the LLDP transmit ETS configuration TLV as part of DCBX TLVs. Having the bit 'etsRecom(2)' set indicates that transmit ETS Recommendation TLV as part of DCBX TLVs. Having the bit 'applicationPriorityFCOE(3)' set indicates that the LLDP transmit applicationPriority TLV for FCOE as part of DCBX TLVs. Having the bit 'applicationPriorityISCSI(4)' set indicates that the LLDP transmit applicationPriority TLV for ISCSI as part of DCBX TLVs. |
| dF10DCBXPortTable | 1.3.6.1.4.1.6027.3.15.3.1.2 | not-accessible | Port table contains the DCBX feature status (enabled or disabled). | |
| dF10DCBXPortTableGroup | 1.3.6.1.4.1.6027.3.15.5.2.4 | This group contains the collection of objects describing the DCBX specific information on the particular port. | ||
| C32 dF10DCBXPortTxCount | 1.3.6.1.4.1.6027.3.15.3.1.3.1.13 | Counter32 | read-only | The number of DCBX frames transmitted per interface. |
| DCB dF10DCBXPortVersion | 1.3.6.1.4.1.6027.3.15.3.1.2.1.4 | DcbxVersion | read-write | CIN is Cisco Intel Nuova DCBX (version 1.0). CEE is converged enhanced ethernet DCBX (version 1.06). IEEE is 802-1 az version. The default value is auto. DCBX supports the legacy implementations v1.0 (CIN) and v1.06 (CEE) in addition to standard IEEE version 2.4 DCBX. 1.DCBX starts in standard IEEE mode by sending an IEEE standard version 2.4 DCBX frame. If the peer responds, then IEEE standard version 2.4 DCBX is used,Starts means after a link up, a DCBX timeout (or multiple peer condition) or when commanded by the network operator. If DCBX receives a DCBX frame with an OUI indicating a legacy version, it immediately switches into legacy mode for the detected version and does not wait for the 3x LLDP fast timeout. 2.If no IEEE DCBX response is received within 3 times the LLDP fast transmit timeout period, DCBX immediately transmits a version 1.06 DCBX frame with the appropriate version number. If DCBX receives a DCBX frame with an OUI indicating IEEE standard support, it immediately switches into IEEE standard mode and does not wait for the timer. If DCBX receives a DCBX frame with an OUI indicating legacy mode and a version number indicating version 1.0 support, it immediately switches into legacy 1.0 mode and does not wait for the timer. 3.If no version 1.06 response is received within 3 times the DCBX fast transmit timeout period, DCBX falls back to version 1.0 and immediately transmits a version 1.0 frame. If no response is received within 3 times the DCBX fast transmit period, DCBX waits the standard LLDP timeout period, and then begins again with step 1. If DCBX receives a DCBX frame with an OUI indicating IEEE standard mode, it immediately switches into IEEE standard mode. |
| dF10DCBXScalars | 1.3.6.1.4.1.6027.3.15.3.1.1 | |||
| dF10DcbxScalarsGroup | 1.3.6.1.4.1.6027.3.15.5.2.3 | This group represents the DCBX scalars in the DF10 DCB mib. | ||
| DCB dF10ETSAdminMode | 1.3.6.1.4.1.6027.3.15.3.2.2.1.2 | DcbAdminMode | read-only | This object is used to display the Admin mode for ETS feature on the given port. If the mode is 'on(1)',ETS feature is enabled on this port. ETS configurations, either from this system or the remote system will take effect based on DCBX negotiations. If the mode is 'off(2)', ETS feature is disabled on this port. Operational(local) parameters is same as Admin Configuration Parameters. But Operational(local) parameters do not have any impact in the system and dF10ETSOperState is in 'Off' state. dF10ETSDcbxOperState becomes oper up if remote is also disabled. The Operational(local) parameters do not have any impact in the system if this object value is 'on(1)' and dF10ETSModuleStatus is disabled. dF10ETSDcbxOperState will be in 'Off' State. |
| T/F dF10ETSClearCounters | 1.3.6.1.4.1.6027.3.15.3.2.1.3 | TruthValue | read-write | This object when set to TRUE, clears the following counters for the ETS Module: dF10ETSConfTxTLVCounter, dF10ETSConfRxTLVCounter, dF10ETSConfRxTLVErrors, dF10ETSRecoTxTLVCounter, dF10ETSRecoRxTLVCounter, dF10ETSRecoRxTLVErrors. Setting this object to FALSE has no effect. This object always returns FALSE when read. |
| T/F dF10ETSClearTLVCounters | 1.3.6.1.4.1.6027.3.15.3.2.2.1.6 | TruthValue | read-write | This object when set to TRUE, clears the following counters associated with a Port: dF10ETSConfTxTLVCounter, dF10ETSConfRxTLVCounter, dF10ETSConfRxTLVErrors, dF10ETSRecoTxTLVCounter, dF10ETSRecoRxTLVCounter, dF10ETSRecoRxTLVErrors. Setting this object to FALSE has no effect. This object always returns FALSE when read. |
| C32 dF10ETSConfRxTLVCounter | 1.3.6.1.4.1.6027.3.15.3.2.2.1.8 | Counter32 | read-only | This object is used to keep track of the number of ETS ConfigurationTLV that are received in this port. This counter will be incremented every time when there is ETS Configuration TLV is received from the LLDP. |
| C32 dF10ETSConfRxTLVErrors | 1.3.6.1.4.1.6027.3.15.3.2.2.1.9 | Counter32 | read-only | This object is used to keep track of number of malformed ETS Conf TLVs received by ETS. This counter will be incremented every time a ETS Conf TLV is dropped by ETS. |
| C32 dF10ETSConfTxTLVCounter | 1.3.6.1.4.1.6027.3.15.3.2.2.1.7 | Counter32 | read-only | This object is used to keep track of the number of ETS configuration TLV that are transmitted from this port. This counter will be incremented every time when there is ETS Configuration TLV is generated and transmitted to the LLDP. |
| DCB dF10ETSDcbxOperState | 1.3.6.1.4.1.6027.3.15.3.2.2.1.3 | DcbState | read-only | This object is used to display the current state of the DCBX state machine for the ETS feature on the given port. If state is Off '(0)', then ETS Operational(local) parameters will be same as ETS Admin Configuration Parameters and will not have any impact in the system(hardware). If state is init '(1)', then ETS Operational(local) parameters will be same as ETS Admin Configuration Parameters. If state is rxrecommended '(2)', then ETS Operational(local) parameters will be same as ETS Remote Parameters. internallypropagated '(3)', In this state all the Operational(local) parameters for the feature will be same as the internal propagated information from the config source. |
| DCB dF10ETSDcbxStateMachine | 1.3.6.1.4.1.6027.3.15.3.2.2.1.4 | DcbStateMachineType | read-only | This object is used to display the DCBX state machine type that is used by the ETS feature on the given port. |
| I32 dF10ETSGlobalEnableTrap | 1.3.6.1.4.1.6027.3.15.3.2.1.4 | Integer32 | read-only | This object indicates whether the transmission of TRAP notification messages for ETS feature is enabled or disabled. |
| ENA dF10ETSModuleStatus | 1.3.6.1.4.1.6027.3.15.3.2.1.2 | EnabledStatus | read-only | The ETS(Enhanced Transmission Selection) Module status for the switch. If this object returns with 'disabled', then all the ports have the ETS feature disabled in the system(hardware) and the DCBX state machine has stopped on the ports. If this object returns with 'enabled', then all the ports have the ETS feature enabled in the system(hardware) and the DCBX state machine is running on the ports. |
| NTF dF10ETSModuleStatusTrap | 1.3.6.1.4.1.6027.3.15.4.0.1 | This trap is generated when there is a change in the ETS Module status. This trap is generated only if dF10ETSGlobalEnableTrap is enabled to send the trap. | ||
| dF10ETSObjects | 1.3.6.1.4.1.6027.3.15.3.2 | |||
| ENA dF10ETSOperStatus | 1.3.6.1.4.1.6027.3.15.3.2.2.1.5 | EnabledStatus | read-only | This object gives information on the operational status of ETS on the given port. Enabled(1) indicates ETS on the port is in sync with the remote and is operationally up. Disabled(2) indicates ETS on the port is operationally disabled. |
| NTF dF10ETSPortAdminStatusTrap | 1.3.6.1.4.1.6027.3.15.4.0.2 | This trap is generated in the following conditions. Whenever there is a change in the ETS Admin status and the dF10ETSGlobalEnableTrap is enabled to send the trap for ETS Admin mode change. | ||
| NTF dF10ETSPortDcbxOperStateTrap | 1.3.6.1.4.1.6027.3.15.4.0.4 | This trap is generated in the following conditions. Whenever there is a change in the ETS Operational State and the dF10ETSGlobalEnableTrap is enabled to send the trap for ETS state machine state change. | ||
| dF10ETSPortEntry | 1.3.6.1.4.1.6027.3.15.3.2.2.1 | not-accessible | An entry containing ETS control parameters and ETS information for a particular port. | |
| NUM dF10ETSPortNumber | 1.3.6.1.4.1.6027.3.15.3.2.2.1.1 | InterfaceIndex | not-accessible | This indicates the interface identifier for which the ETS configuration is applied. |
| NTF dF10ETSPortPeerStatusTrap | 1.3.6.1.4.1.6027.3.15.4.0.3 | This trap is generated in the following conditions. Whenever there is a change in the DCBX Peer Status and the dF10ETSGlobalEnableTrap is enabled to send the trap for Peer Up or Peer Down. | ||
| dF10ETSPortTable | 1.3.6.1.4.1.6027.3.15.3.2.2 | not-accessible | ETS Port table contains the ETS (Enhanced Transmission Selection) features information specific to this port. An entry created in this table in the following tables in the standard DCBX Mib for this port. lldpXdot1dcbxConfigTCSupportedTable, lldpXdot1dcbxConfigETSConfigurationTable, lldpXdot1dcbxConfigETSRecommendationTable, lldpXdot1dcbxLocTCSupportedTable, lldpXdot1dcbxLocETSBasicConfigurationTable, lldpXdot1dcbxLocETSConPriorityAssignmentTable, lldpXdot1dcbxLocETSRecommendationTable, lldpXdot1dcbxAdminTCSupportedTable, lldpXdot1dcbxAdminETSBasicConfigurationTable, lldpXdot1dcbxAdminETSConPriorityAssignmentTable, lldpXdot1dcbxAdminETSRecommendationTable. Deletion of entry in this table deletes all the entries in the above tables in the standatd DCBX mib for this port. | |
| dF10ETSPortTableGroup | 1.3.6.1.4.1.6027.3.15.5.2.6 | This object group represents the collection of objects providing ETS specific status information on a specific port. | ||
| C32 dF10ETSRecoRxTLVCounter | 1.3.6.1.4.1.6027.3.15.3.2.2.1.11 | Counter32 | read-only | This object is used to keep track of the number of ETS Recommendation TLV that are received in this port. This counter will be incremented every time when there is ETS Recommendation TLV is received from the LLDP. |
| C32 dF10ETSRecoRxTLVErrors | 1.3.6.1.4.1.6027.3.15.3.2.2.1.12 | Counter32 | read-only | This object is used to keep track of number of malformed ETS Reco TLVs received by ETS. This counter will be incremented every time a ETS Reco TLV is dropped by ETS. |
| C32 dF10ETSRecoTxTLVCounter | 1.3.6.1.4.1.6027.3.15.3.2.2.1.10 | Counter32 | read-only | This object is used to keep track of the number of ETS Recommendation TLV that are transmitted from this port. This counter will be incremented every time when there is ETS Recommendation TLV is generated and transmitted to the LLDP. |
| dF10ETSScalars | 1.3.6.1.4.1.6027.3.15.3.2.1 | |||
| dF10ETSScalarsGroup | 1.3.6.1.4.1.6027.3.15.5.2.5 | This object represents the collection of objects providing the ETS Information on the system. | ||
| INT dF10ETSSystemControl | 1.3.6.1.4.1.6027.3.15.3.2.1.1 | INTEGER | read-only | The ETS(Enhanced Transmission selection) system control status for the switch. It indicates whether ETS Module in the system is running or shutdown. When this object returns 'running', resources required by ETS module are allocated and the module is running. When this object returns 'shutdown', all the pools used by ETS module are released to the system. |
| DCB dF10PFCAdminMode | 1.3.6.1.4.1.6027.3.15.3.3.2.1.2 | DcbAdminMode | read-only | This object is used to display Admin mode for PFC feature on the given port. If mode is 'on(1)',PFC feature is enabled on this port. PFC configurations, either from this system or the remote system will take effect based on DCBX negotiations. If mode is 'off(2)',PFC feature is disabled on this port. Operational(local) parameters is same as Admin Configuration Parameters. But Operational(local) parameters do not have any impact in the system.dF10PFCDcbxOperState becomes up if remote is also disabled The Operational(local) parameters do not have any impact in the system if this object value is 'on(1)' and dF10PFCModuleStatus is disabled. dF10PFCDcbxOperState will be in 'Off' State. |
| T/F dF10PFCClearCounters | 1.3.6.1.4.1.6027.3.15.3.3.1.3 | TruthValue | read-write | This object when set to TRUE, clears the following counters for the PFC Module: dF10PFCTxTLVCounter, dF10PFCRxTLVCounter, dF10PFCRxTLVErrors. Setting this object to FALSE has no effect. This object always returns FALSE when read. |
| T/F dF10PFCClearTLVCounters | 1.3.6.1.4.1.6027.3.15.3.3.2.1.6 | TruthValue | read-write | This object when set to TRUE, clears the following counters associated with a Port: dF10PFCTxTLVCounter, dF10PFCRxTLVCounter, dF10PFCRxTLVErrors. Setting this object to FALSE has no effect. This object always returns FALSE when read. |
| DCB dF10PFCDcbxOperState | 1.3.6.1.4.1.6027.3.15.3.3.2.1.3 | DcbState | read-only | This object is used to display the current state of the DCBX state machine for the PFC feature on the given port. If state is Off '(0)', then PFC Operational(local) parameters will be same as PFC Admin Configuration Parameters and will not have any impact in the system(hardware). If state is init '(1)', then PFC Operational(local) parameters will be same as PFC Admin Configuration Parameters. If state is rxrecommended '(2)',then PFC Operational(local) parameters will be same as PFC Remote Parameters. internallypropagated '(3)', In this state all the Operational(local) parameters for the feature will be same as the internal propagated information from the config source. |
| DCB dF10PFCDcbxStateMachine | 1.3.6.1.4.1.6027.3.15.3.3.2.1.4 | DcbStateMachineType | read-only | This object is used to display the DCBX state machine type that is used by the PFC feature on the given port. |
| I32 dF10PFCGlobalEnableTrap | 1.3.6.1.4.1.6027.3.15.3.3.1.4 | Integer32 | read-only | This object indicates whether the transmission of TRAP notification messages for PFC feature is enabled or disabled. |
| ENA dF10PFCModuleStatus | 1.3.6.1.4.1.6027.3.15.3.3.1.2 | EnabledStatus | read-only | The PFC(Priority Based Flow Control) Module status for the switch. If this object returns with 'disabled', then all the ports have the PFC feature disabled in the system(hardware) and the DCBX state machine has stopped on the ports. If this object returns with 'enabled', then all the ports have the PFC feature enabled in the system(hardware) and the DCBX state machine is running on the ports. |
| NTF dF10PFCModuleStatusTrap | 1.3.6.1.4.1.6027.3.15.4.0.5 | This trap is generated when there is a change in the PFC Module status is enabled. This trap is generated only if dF10PFCGlobalEnableTrap is enabled to send the trap. | ||
| dF10PFCObjects | 1.3.6.1.4.1.6027.3.15.3.3 | |||
| ENA dF10PFCOperStatus | 1.3.6.1.4.1.6027.3.15.3.3.2.1.5 | EnabledStatus | read-only | This object gives information on the operational status of PFC on the given port. Enabled(1) indicates PFC on the port is in sync with the remote and is operationally up. Disabled(2) indicates PFC on the port is operationally disabled. |
| NTF dF10PFCPortAdminStatusTrap | 1.3.6.1.4.1.6027.3.15.4.0.6 | This trap is generated in the following conditions. Whenever there is a change in the PFC Admin Status and the dF10PFCGlobalEnableTrap is enabled to send the trap for PFC Admin Status change. | ||
| NTF dF10PFCPortDcbxOperStateTrap | 1.3.6.1.4.1.6027.3.15.4.0.8 | This trap is generated in the following conditions. Whenever there is a change in the PFC Operational State and the dF10PFCGlobalEnableTrap is enabled to send the trap for PFC state machine state change. | ||
| dF10PFCPortEntry | 1.3.6.1.4.1.6027.3.15.3.3.2.1 | not-accessible | An entry containing PFC control parameters and PFC information for a particular port. | |
| NUM dF10PFCPortNumber | 1.3.6.1.4.1.6027.3.15.3.3.2.1.1 | InterfaceIndex | not-accessible | This indicates the interface identifier for which the PFC configuration is applied. |
| NTF dF10PFCPortPeerStatusTrap | 1.3.6.1.4.1.6027.3.15.4.0.7 | This trap is generated in the following conditions. Whenever there is a change in the DCBX Peer Status and the dF10PFCGlobalEnableTrap is enabled to send the trap for Peer Up or Peer Down. | ||
| dF10PFCPortTable | 1.3.6.1.4.1.6027.3.15.3.3.2 | not-accessible | PFC Port table contains the PFC (Priortiy Based Flow Control) features information specific to this port. An entry created in the port table populates the entry in this table and in the following tables in the standard DCBX Mib for this port. lldpXdot1dcbxConfigPFCTable, lldpXdot1dcbxLocPFCBasicTable, lldpXdot1dcbxLocPFCEnableTable, lldpXdot1dcbxAdminPFCBasicTable, lldpXdot1dcbxAdminPFCEnableTable. Deletion of entry in the port table deletes the entry in this table and all the entries in the above tables in the standatd DCBX mib for this port. | |
| dF10PFCPortTableGroup | 1.3.6.1.4.1.6027.3.15.5.2.8 | This group represents a collection of objects providing the PFC specific status information per port. | ||
| C32 dF10PFCRxTLVCounter | 1.3.6.1.4.1.6027.3.15.3.3.2.1.8 | Counter32 | read-only | This object is used to keep track of the number of PFC TLV that are received in this port. This counter will be incremented every time when there is PFC TLV is received from the LLDP. |
| C32 dF10PFCRxTLVErrors | 1.3.6.1.4.1.6027.3.15.3.3.2.1.9 | Counter32 | read-only | This object is used to keep track of number of malformed TLVs received by PFC. This counter will be incremented every time a PFC-TLV is dropped by PFC. |
| dF10PFCScalars | 1.3.6.1.4.1.6027.3.15.3.3.1 | |||
| dF10PFCScalarsGroup | 1.3.6.1.4.1.6027.3.15.5.2.7 | This group represents a collection of objects providing the system information related to PFC. | ||
| INT dF10PFCSystemControl | 1.3.6.1.4.1.6027.3.15.3.3.1.1 | INTEGER | read-only | The PFC(Priority Based Flow Control) system control status for the switch. It indicates whether PFC Module in the system is running or shutdown. When this object returns 'running', resources required by PFC module are allocated and the module is running. When this object returns 'shutdown', all the pools used by PFC module are released to the system. |
| C32 dF10PFCTxTLVCounter | 1.3.6.1.4.1.6027.3.15.3.3.2.1.7 | Counter32 | read-only | This object is used to keep track of the number of PFC TLV that are transmitted from this port. This counter will be incremented every time when there is PFC TLV is generated and transmitted to the LLDP. |
RFC description
Data Center Bridging configuration MIB for Dell Networking OS switches supporting PFC and ETS.
Start monitoring Dell Networking (Force10) data center switch (DCB/DCBX) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.