| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ibm | 1.3.6.1.4.1.2 | | | |
| ibmProd | 1.3.6.1.4.1.2.6 | | | |
| ibmSP | 1.3.6.1.4.1.2.6.117 | | | |
| ibmSPDepNode | 1.3.6.1.4.1.2.6.117.4 | | | |
| NTF switchInfoNeeded | 1.3.6.1.4.1.2.6.117.4.0.1 | | | A switchInfoNeeded trap signifies that the sending protocol entity needs SP switch configuration information for a dependent secondary node within the sender's configuration. |
| NTF switchConfigState | 1.3.6.1.4.1.2.6.117.4.0.2 | | | A switchConfigState trap indicates the final configuration state of a dependent secondary node's SP switch interface. |
| NTF switchNodeUp | 1.3.6.1.4.1.2.6.117.4.0.3 | | | A switchNodeUp trap indicates that a dependent secondary node in the sender's configuration has just been reinitialized or reconfigured and is able to handle SP Switch Manager protocol messages. |
| NTF switchNodeDown | 1.3.6.1.4.1.2.6.117.4.0.4 | | | A switchNodeDown trap indicates that a dependent secondary node in the sender's configuration is no longer able to handle Switch Manager protocol messages on the switch network. |
| ibmSPDepNodeTable | 1.3.6.1.4.1.2.6.117.4.1 | | not-accessible | This entity's table of dependent secondary nodes
attached to IBM SP switch networks. |
| ibmSPDepNodeEntry | 1.3.6.1.4.1.2.6.117.4.1.1 | | not-accessible | Configuration information for a dependent
secondary node on SP switch network. |
| STR ibmSPDepNodeName | 1.3.6.1.4.1.2.6.117.4.1.1.1 | DisplayString | read-only | Identifier assigned to this node in its
system's administrative environment. |
| INT ibmSPDepNodeNumber | 1.3.6.1.4.1.2.6.117.4.1.1.2 | INTEGER | read-write | Relative node number assigned to this node in the SP system.
Note that this is distinct from switch node number. |
| OCT ibmSPDepSwToken | 1.3.6.1.4.1.2.6.117.4.1.1.3 | OCTET STRING | read-write | Opaque correlator assigned in the SP system
for this node's switch connection. |
| INT ibmSPDepSwARP | 1.3.6.1.4.1.2.6.117.4.1.1.4 | INTEGER | read-write | Indicates whether ARP is enabled for the partition
of the switch network that contains the associated
dependent secondary node.
NOTE: An SNMP Agent may be responsible for switch
nodes in several SP system partitions, and ARP
may be enabled in none, some, or all of the partitions.
A value of disabled(1) indicates that ARP is
not to be used to resolve network protocol
addresses to switch node numbers for the switch
network. Instead, the mapping of IP addresses
to switch node numbers is determined via the
algorithm in the description of ibmSPDepIPHostOffset.
A value of enabled(2) indicates that ARP is
to be used to resolve network protocol
addresses to switch node numbers for the switch
network. |
| INT ibmSPDepSwNodeNumber | 1.3.6.1.4.1.2.6.117.4.1.1.5 | INTEGER | read-write | The switch node number of the associated SP switch
interface. In common networking terminology,
this is the physical address for the interface
on the SP switch network, and is also called
the Node Device ID in the SP dependent node
architecture. |
| IP ibmSPDepIPaddr | 1.3.6.1.4.1.2.6.117.4.1.1.6 | IpAddress | read-write | The IP address for the associated SP switch interface. |
| IP ibmSPDepNetMask | 1.3.6.1.4.1.2.6.117.4.1.1.7 | IpAddress | read-write | The subnet mask associated with the IP address of
this entry. The value of the mask is an IP
address with all the network bits set to 1 and all
the host bits set to 0. |
| INT ibmSPDepIPMaxLinkPkt | 1.3.6.1.4.1.2.6.117.4.1.1.8 | INTEGER | read-write | The maximum number of bytes in the data portion of
link-layer packets for IP datagrams on the
SP switch network. |
| INT ibmSPDepIPHostOffset | 1.3.6.1.4.1.2.6.117.4.1.1.9 | INTEGER | read-write | This value is the difference between switch node
numbers and the host portion of the corresponding
IP addresses when ARP is disabled on the SP switch
network. It is the value to subtract from the
host portion of an IP address to calculate the
corresponding switch node number. |
| INT ibmSPDepConfigState | 1.3.6.1.4.1.2.6.117.4.1.1.10 | INTEGER | read-only | This value indicates the final configuration state
of the corresponding SP switch interface. |
| STR ibmSPDepSysName | 1.3.6.1.4.1.2.6.117.4.1.1.11 | DisplayString | read-write | The fully-qualified domain name of the SP system
partition that contains this dependent node. This
name is administratively assigned in the SP system. |
| INT ibmSPDepNodeState | 1.3.6.1.4.1.2.6.117.4.1.1.12 | INTEGER | read-only | This value indicates the state of the dependent
node with respect to its capability to handle
Switch Manager protocol via its SP switch interface.
A value of nodeUp(1) indicates that the node has
been reinitialized or reconfigured sufficiently
to handle the Switch Manager protocol to unfence
the node if it were previously fenced from the
SP switch network.
A value of nodeDown(2) indicates that the node is
no longer able to handle Switch Manager protocol
messages on the SP switch network. |
| INT ibmSPDepSwChipLink | 1.3.6.1.4.1.2.6.117.4.1.1.13 | INTEGER | read-write | The send port number for packets from the
adjacent switch chip to the dependent node.
The dependent node needs this value to build
the packet that it sends to the adjacent
switch chip to trigger that chip to reply
with a clock synchronization packet. |
| INT ibmSPDepNodeDelay | 1.3.6.1.4.1.2.6.117.4.1.1.14 | INTEGER | read-write | This value is an estimate of how many clock
cycles elapse before a clock synchronization packet
sent from the adjacent switch chip to the dependent node
results in loading of the switch time-of-day register
for the node.
The dependent node needs this value to build
the packet that it sends to the adjacent
switch chip to trigger that chip to reply with
a clock synchronization packet. |
| INT ibmSPDepAdminStatus | 1.3.6.1.4.1.2.6.117.4.1.1.15 | INTEGER | read-write | This value indicates the desired state of the dependent
node with respect to its capability to handle
Switch Manager protocol via its SP switch interface.
If the dependent node is not in the desired state,
then the SNMP Agent triggers actions to change its state
to the desired state.
A value of up(1) indicates that the node should be
initialized and configured sufficiently
to handle the Switch Manager protocol.
A value of down(2) indicates that the node should be
reset such that it is not able to receive and handle
Switch Manager protocol messages on the SP switch
network.
A value of reconfigure(3) indicates that the SNMP Agent
must send the switchInfoNeeded trap to request new SP
switch configuration information for the dependent
node. This causes the SNMP Manager to send the
new configuration information for the dependent node
MIB objects via set-request PDU(s).
Once the new values are set by the SNMP Manager,
the SNMP Agent reinitializes and reconfigures the dependent
node sufficiently to handle the Switch Manager protocol. |
