All MIBs › DELLEMC-OS10-BGP4V2-MIB
Organization: Dell EMC
Last Updated: 2020-02-25
Category: Routing Protocols, Vendor: Dell
Description: Manages BGP4 peer sessions, routing policy, and path attributes for Dell EMC OS10 switches.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is DELLEMC-OS10-BGP4V2-MIB?
DELLEMC-OS10-BGP4V2-MIB is a Dell EMC vendor MIB for switches running the OS10 network operating system, providing management of the BGP-4 (and multiprotocol/v2) routing protocol. It belongs to the Dell EMC OS10 networking software family and exposes BGP peer session state, routing policy application, and path attribute data for exchanged routes. For monitoring purposes it is primarily used to track software/protocol status rather than physical hardware: administrators use it to confirm BGP peering sessions are established, watch for flapping neighbors, and verify route counts and policy application are behaving as configured. It explicitly implements/extends the IETF BGP4-MIB (and its v2/multiprotocol successor) conventions, so it is tightly coupled to that standards-based routing MIB structure. It is typically deployed on Dell EMC PowerSwitch (OS10-based) data center and campus switches that participate in BGP routing, such as leaf-spine data center fabrics. Network engineers evaluating or troubleshooting this functionality can download the DELLEMC-OS10-BGP4V2-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in DELLEMC-OS10-BGP4V2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Dell EMC PowerSwitch (OS10-based) switches
Monitoring Examples
An operator would poll a BGP peer table (analogous to bgpPeerTable/bgpPeerEntry) to check bgpPeerState for each configured neighbor, alerting if a peer transitions out of the Established state, which would indicate a routing adjacency failure. Path attribute objects would be checked to confirm that a route's AS-path or next-hop reflects the expected routing policy, helping diagnose unexpected route selection in a leaf-spine fabric. Because this MIB covers protocol-level software state rather than chassis sensors, it is typically polled alongside hardware-focused Dell OS10 MIBs for a complete health picture.
What Can Be Monitored
- BGP peer/session state
- peer established/down transitions
- route path attributes
- routing policy application
- AS path / next-hop data
This MIB depends on
Related MIBs
Imported Objects
From DELLEMC-OS10-SMI-MIB
| os10Experiment | OBJECT-IDENTITY |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressPrefixLength | |
| InetAddressType | |
| InetAutonomousSystemNumber | |
| InetPortNumber |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowPointer | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| os10bgp4V2AdjRibsOutEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.10.1 | not-accessible | List of BGP routes that have been placed into a peer's Adj-Ribs-Out. | |
| U32 os10bgp4V2AdjRibsOutIndex | 1.3.6.1.4.1.674.11000.5000.200.1.1.10.1.1 | Unsigned32 | not-accessible | Certain extensions to BGP permit multiple instance of a per afi, per safi prefix to be advertised to a peer. This object allows the enumeration of them. |
| NUM os10bgp4V2AdjRibsOutRoute | 1.3.6.1.4.1.674.11000.5000.200.1.1.10.1.2 | RowPointer | read-only | This object points to the route in the os10bgp4V2NlriTable that corresponds to the entry in the peer's Adj-Rib-Out. Outgoing route maps are not reflected at this point as those are part of the Update-Send process. |
| os10bgp4V2AdjRibsOutTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.10 | not-accessible | This table contains on a per-peer basis one or more routes from the os10bgp4V2NlriTable that have been placed in this peer's Adj-Ribs-Out. | |
| os10bgp4V2Conformance | 1.3.6.1.4.1.674.11000.5000.200.1.2 | |||
| os10bgp4V2DiscontinuityEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.1.1 | not-accessible | Entry repsenting information about a discontinuity event for a given BGP instance. | |
| os10bgp4V2DiscontinuityTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.1 | not-accessible | Table of BGP-4 discontinuities. Discontinuities that have external visibility occur on a per-BGP instance basis. Transitions by a given BGP peer will result in a consistent BGP view within that instance and thus do not represent a discontinuity from a protocol standpoint. | |
| TIM os10bgp4V2DiscontinuityTime | 1.3.6.1.4.1.674.11000.5000.200.1.1.1.1.1 | TimeStamp | read-only | The value of sysUpTime at the most recent occasion at which this BGP management instance has suffered a discontinuity. |
| os10Bgp4V2Mib | 1.3.6.1.4.1.674.11000.5000.200.1 | The MIB module for the BGP-4 protocol. | ||
| ADR os10bgp4V2NlriAfi | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.2 | Os10Bgp4V2AddressFamilyIdentifierTC | not-accessible | The address family of the prefix for this NLRI. Note that the AFI is not necessarily equivalent to the an InetAddressType. |
| OID os10bgp4V2NlriAggregatorAddr | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.21 | Os10Bgp4V2IdentifierTC | read-only | The IP address of the last BGP4 speaker that performed route aggregation. When os10bgp4V2NlriAggregatorPresent is false, the value of this object should be 0.0.0.0 |
| INE os10bgp4V2NlriAggregatorAS | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.20 | InetAutonomousSystemNumber | read-only | The AS number of the last BGP4 speaker that performed route aggregation. When os10bgp4V2NlriAggregatorPresent is false, the value of this object should be zero (0). |
| T/F os10bgp4V2NlriAggregatorPresent | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.19 | TruthValue | read-only | This value is true when the AGGREGATOR path attribute was sent in the UPDATE message. |
| OCT os10bgp4V2NlriAsPath | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.24 | OCTET STRING | read-only | In order to provide a canonicalized form of the BGP-4 AS_PATH along with the human-readable os10bgp4V2NlriAsPathString, which may be truncated, this object contains the contents of the BGP-4 AS_PATH Path Attribute. This object may be parsed using the rules defined for Four-octet ASes as defined in RFC 4893. RFC 4271, Section 4.3, 'Path Attributes: b) AS_PATH' as amended by RFC 5065, Section 3 defines the general format of the AS_PATH path attribute and its code points. In brief, the AS_PATH is composed of a sequence of AS Segments. Each AS Segment is represented by a triple: . The path segment type and path segment length fields are one octet in length each. The path segment type field may be one of: 1 - AS_SET (RFC 4721, Section 4.3) 2 - AS_SEQUENCE (RFC 4721, Section 4.3) 3 - AS_CONFED_SEQUENCE (RFC 3065, Section 5) 4 - AS_CONFED_SET (RFC 3065, Section 5) The path segment length field contains the number of ASes (not the number of octets) in the path segment value field. The path segment value field contains one or more AS numbers, each encoded as a 4-octet length field in network byte order. Note that since an SNMP agent may truncate this object to less than its maximum theoretical length of 4072 octets users of this object should be prepared to deal with a truncated and thus malformed AS_PATH. It is RECOMMENDED that when such truncation would occur on the boundary of an encoded AS that the partial AS be discarded from this object and the object's size be adjusted accordingly. Further, it is also RECOMMENDED that when such truncation, either alone or in conjuction with the truncation of a partially encoded AS described previously, would yield an empty path segment value field that the path segment type and path segment length components of the truncated AS_PATH also be discarded and the object's size be adjusted accordingly. |
| U32 os10bgp4V2NlriAsPathCalcLength | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.22 | Unsigned32 | read-only | This value represents the calculated length of the AS Path according to the rules of the BGP specification. This value is used in route selection. |
| STR os10bgp4V2NlriAsPathString | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.23 | SnmpAdminString | read-only | This is a string depicting the autonomous system path to this network which was received from the peer which advertised it. The format of the string is implementation-dependent, and should be designed for operator readability. Note that SnmpAdminString is only capable of representing a maximum of 255 characters. This may lead to the string being truncated in the presence of a large AS Path. It is RECOMMENDED that when this object's contents will be truncated that the final 3 octets be reserved for the ellipses string, '...'. os10bgp4V2NlriAsPath may give access to the full AS Path. |
| T/F os10bgp4V2NlriAtomicAggregate | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.18 | TruthValue | read-only | This value is true when the ATOMIC_AGGREGATE Path Attribute is present and indicates that the NLRI MUST NOT be made more specific. |
| T/F os10bgp4V2NlriBest | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.7 | TruthValue | read-only | An indication of whether or not this route was chosen as the best BGP4 route for this destination. |
| U32 os10bgp4V2NlriCalcLocalPref | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.8 | Unsigned32 | read-only | The degree of preference calculated by the receiving BGP4 speaker for an advertised route. In the case where this prefix is ineligible, the value of this object will be zero (0). |
| os10bgp4V2NlriEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1 | not-accessible | Information about a path to a network. | |
| U32 os10bgp4V2NlriIndex | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.1 | Unsigned32 | not-accessible | This index allows for multiple instances of a base prefix for a certain AFI-SAFI from a given peer. This is currently useful for two things: 1. Allowing for a peer in future implementations to send more than a single route instance. 2. Allow for extensions which extend the NLRI field to send the same prefix while utilizing other extension specific information. An example of this is RFC 3107 - Carrying MPLS labels in BGP. |
| IP os10bgp4V2NlriLinkLocalNextHopAddr | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.13 | InetAddress | read-only | This value contains an IPv6 link local address and is present only when receiving RFC 2545 style double nexthops. This object is optionally present in BGP implementations that do not support IPv6. When no IPv6 link local nexthop is present, the length of this object should be zero. |
| IPt os10bgp4V2NlriLinkLocalNextHopAddrType | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.12 | InetAddressType | read-only | The address type for IPv6 link local addresses. This is present only when receiving RFC 2545 style double nexthops. This object is optionally present in BGP implementations that do not support IPv6. When no IPv6 link local nexthop is present, the value of this object should be unknown(0). |
| U32 os10bgp4V2NlriLocalPref | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.15 | Unsigned32 | read-only | The originating BGP4 speakers degree of preference for an advertised route. |
| T/F os10bgp4V2NlriLocalPrefPresent | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.14 | TruthValue | read-only | This value is true when the LOCAL_PREF value was sent in the UPDATE message. |
| U32 os10bgp4V2NlriMed | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.17 | Unsigned32 | read-only | This metric is used to discriminate between multiple exit points to an adjacent autonomous system. When the MED value is absent but has a calculated default value, this object will contain the calculated value. |
| T/F os10bgp4V2NlriMedPresent | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.16 | TruthValue | read-only | This value is true when the MED value was sent in the UPDATE message. |
| IP os10bgp4V2NlriNextHopAddr | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.11 | InetAddress | read-only | The address of the border router that should be used to access the destination network. This address is the nexthop address received in the UPDATE packet associated with this prefix. Note that for RFC2545 style double nexthops, this object will always contain the global scope nexthop. bgpPathAttrLinkLocalNextHop will contain the linklocal scope nexthop, if it is present. In the case a mechanism is developed to use only a link local nexthop, os10bgp4V2NlriNextHopAddr will contain the link local nexthop. |
| IPt os10bgp4V2NlriNextHopAddrType | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.10 | InetAddressType | read-only | The address family of the address for the border router that should be used to access the destination network. |
| INT os10bgp4V2NlriOrigin | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.9 | INTEGER | read-only | The ultimate origin of the path information. |
| OCT os10bgp4V2NlriPathAttrUnknown | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.25 | OCTET STRING | read-only | Path Attributes not understood by this implementation SHOULD be be presented in this object. Those Path Attributes use the type, length, value encoding documented in RFC 4271, Section 4.3, 'Path Attributes'. Note that since an SNMP agent may truncate this object to less than its maximum theoretical length of 4072 octets users of this object should be prepared to deal with a truncated and thus malformed Path Attribute. |
| IP os10bgp4V2NlriPrefix | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.5 | InetAddress | not-accessible | An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by os10bgp4V2NlriPrefixLen. Any bits beyond the length specified by os10bgp4V2NlriPrefixLen are zeroed. An implementation is required to support IPv4 prefixes. In this case, the object length is (0..4). An implementation MAY support IPv6 prefixes. In this case, the object length is (0..16) |
| ADR os10bgp4V2NlriPrefixLen | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.6 | InetAddressPrefixLength | not-accessible | Length in bits of the address prefix in the Network Layer Reachability Information field. |
| IPt os10bgp4V2NlriPrefixType | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.4 | InetAddressType | not-accessible | The type of the IP address prefix in the Network Layer Reachability Information field. The value of this object is derived from the appropriate value from the os10bgp4V2NlriAfi field. Where an appropriate InetAddressType is not available, the value of the object must be unknown(0). |
| ADR os10bgp4V2NlriSafi | 1.3.6.1.4.1.674.11000.5000.200.1.1.9.1.3 | Os10Bgp4V2SubsequentAddressFamilyIdentifierTC | not-accessible | The subsequent address family of the prefix for this NLRI |
| os10bgp4V2NlriTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.9 | not-accessible | The BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers. Collectively, this represents the Adj-Ribs-In. The route where os10bgp4V2NlriBest is true represents, for this NLRI, the route that is installed in the LocRib from the Adj-Ribs-In. | |
| os10bgp4V2Notifications | 1.3.6.1.4.1.674.11000.5000.200.1.0 | |||
| os10bgp4V2Objects | 1.3.6.1.4.1.674.11000.5000.200.1.1 | |||
| INT os10bgp4V2PeerAdminStatus | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.12 | INTEGER | read-only | Whether or not the BGP FSM for this remote peer is halted or running. The BGP FSM for a remote peer is halted after processing a Stop event. Likewise, it is in the running state after a Start event. The os10bgp4V2PeerState will generally be in the idle state when the FSM is halted, although some extensions such as Graceful Restart will leave the peer in the Idle state but with the FSM running. |
| os10bgp4V2PeerConfiguredTimersEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.5.1 | not-accessible | Each entry corresponds to the current state of BGP timers on a given peering session. | |
| os10bgp4V2PeerConfiguredTimersTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.5 | not-accessible | Per peer management data on BGP session timers. | |
| U32 os10bgp4V2PeerConnectRetryInterval | 1.3.6.1.4.1.674.11000.5000.200.1.1.5.1.1 | Unsigned32 | read-only | Time interval (in seconds) for the ConnectRetry timer. The suggested value for this timer is 120 seconds. |
| os10bgp4V2PeerCountersEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.7.1 | not-accessible | Each entry contains counters of message transmissions and FSM transitions for a given BGP Peering session. | |
| os10bgp4V2PeerCountersTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.7 | not-accessible | The counters associated with a BGP Peer. | |
| STR os10bgp4V2PeerDescription | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.14 | SnmpAdminString | read-only | A user configured description identifying this peer. When this object is not the empty string, this object SHOULD contain a description that is unique within a given BGP instance for this peer. |
| os10bgp4V2PeerEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1 | not-accessible | Entry containing information about the connection with a remote BGP peer. | |
| os10bgp4V2PeerErrorsEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1 | not-accessible | Each entry contains information about errors sent and received for a particular BGP peer. | |
| os10bgp4V2PeerErrorsTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.3 | not-accessible | On a per-peer basis, this table reflects the last protocol-defined error encountered and reported on the peer session. | |
| os10bgp4V2PeerEventTimesEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.4.1 | not-accessible | Each row contains a set of statistics about time spent and events encountered in the peer session established state. | |
| os10bgp4V2PeerEventTimesTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.4 | not-accessible | A table reporting the per-peering session amount of time elapsed and update events since the peering session advanced into the established state. | |
| G32 os10bgp4V2PeerFsmEstablishedTime | 1.3.6.1.4.1.674.11000.5000.200.1.1.4.1.1 | Gauge32 | read-only | This timer indicates how long (in seconds) this peer has been in the established state or how long since this peer was last in the established state. It is set to zero when a new peer is configured or when the router is booted. If the peer has never reached the established state, the value remains zero. |
| C32 os10bgp4V2PeerFsmEstablishedTransitions | 1.3.6.1.4.1.674.11000.5000.200.1.1.7.1.5 | Counter32 | read-only | The total number of times the BGP FSM transitioned into the established state for this peer. |
| U32 os10bgp4V2PeerHoldTime | 1.3.6.1.4.1.674.11000.5000.200.1.1.6.1.1 | Unsigned32 | read-only | The value of this object is calculated by this BGP Speaker as being; zero (0) - if this was the value sent by the peer and this value is permitted by this BGP Speaker. In this case, no keepalive messages are sent and the Hold Timer is not set. At least three (3). This value is the smaller of the value sent by this peer in the OPEN message and os10bgp4V2PeerHoldTimeConfigured for this peer. If the peer is not in the established state, the value of this object is zero (0). |
| U32 os10bgp4V2PeerHoldTimeConfigured | 1.3.6.1.4.1.674.11000.5000.200.1.1.5.1.2 | Unsigned32 | read-only | Time interval (in seconds) for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker, using the smaller of the values in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at least three seconds if it is not zero (0). If the Hold Timer has not been established with the peer this object MUST have a value of zero (0). If the bgpPeerHoldTimeConfigured object has a value of (0), then this object MUST have a value of (0). |
| U32 os10bgp4V2PeerInstance | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.1 | Unsigned32 | not-accessible | The routing instance index. Some BGP implementations permit the creation of multiple instances of a BGP routing process. An example includes routers running BGP/MPLS IP Virtual Private Networks. Implementations that do not support multiple routing instances should return 1 for this object. |
| C32 os10bgp4V2PeerInTotalMessages | 1.3.6.1.4.1.674.11000.5000.200.1.1.7.1.3 | Counter32 | read-only | The total number of messages received from the remote peer on this connection. |
| C32 os10bgp4V2PeerInUpdates | 1.3.6.1.4.1.674.11000.5000.200.1.1.7.1.1 | Counter32 | read-only | The number of BGP UPDATE messages received on this connection. |
| G32 os10bgp4V2PeerInUpdatesElapsedTime | 1.3.6.1.4.1.674.11000.5000.200.1.1.4.1.2 | Gauge32 | read-only | Elapsed time (in seconds) since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is set to zero (0). |
| U32 os10bgp4V2PeerKeepAlive | 1.3.6.1.4.1.674.11000.5000.200.1.1.6.1.2 | Unsigned32 | read-only | Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with os10bgp4V2PeerHoldTime, it has the same proportion as what os10bgp4V2PeerKeepAliveConfigured has when compared with os10bgp4V2PeerHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of os10bgp4V2PeerKeepAliveConfigured is zero (0). If the peer is not in the established state, the value of this object is zero (0). |
| U32 os10bgp4V2PeerKeepAliveConfigured | 1.3.6.1.4.1.674.11000.5000.200.1.1.5.1.3 | Unsigned32 | read-only | Time interval (in seconds) for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodic KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds. |
| U32 os10bgp4V2PeerLastErrorCodeReceived | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.1 | Unsigned32 | read-only | The last error code received from this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero. |
| U32 os10bgp4V2PeerLastErrorCodeSent | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.6 | Unsigned32 | read-only | The last error code sent to this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero. |
| OCT os10bgp4V2PeerLastErrorReceivedData | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.5 | OCTET STRING | read-only | The last error code's data seen by this peer. Per RFC 2578, some implementations may have limitations dealing with OCTET STRINGS larger than 255. Thus, this data may be truncated. |
| STR os10bgp4V2PeerLastErrorReceivedText | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.4 | SnmpAdminString | read-only | This object contains an implementation specific explanation of the error that was reported. |
| TIM os10bgp4V2PeerLastErrorReceivedTime | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.3 | TimeStamp | read-only | The timestamp that the last NOTIFICATION was received from this peer. |
| OCT os10bgp4V2PeerLastErrorSentData | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.10 | OCTET STRING | read-only | The last error code's data sent to this peer. Per RFC 2578, some implementations may have limitations dealing with OCTET STRINGS larger than 255. Thus, this data may be truncated. |
| STR os10bgp4V2PeerLastErrorSentText | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.9 | SnmpAdminString | read-only | This object contains an implementation specific explanation of the error that is being reported. |
| TIM os10bgp4V2PeerLastErrorSentTime | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.8 | TimeStamp | read-only | The timestamp that the last NOTIFICATION was sent to this peer. |
| U32 os10bgp4V2PeerLastErrorSubCodeReceived | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.2 | Unsigned32 | read-only | The last subcode received from this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero. |
| U32 os10bgp4V2PeerLastErrorSubCodeSent | 1.3.6.1.4.1.674.11000.5000.200.1.1.3.1.7 | Unsigned32 | read-only | The last subcode sent to this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero. |
| IP os10bgp4V2PeerLocalAddr | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.3 | InetAddress | read-only | The local IP address of this entry's BGP connection. An implementation is required to support IPv4 peering sessions in which case the length of this object is 4. An implementation MAY support IPv6 peering sessions in which case the length of this object is 16. IPv6 link-local peering sessions MAY be supported by this MIB. In this case the length of this object is 20. |
| IPt os10bgp4V2PeerLocalAddrType | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.2 | InetAddressType | read-only | The address family of the local end of the peering session. |
| INE os10bgp4V2PeerLocalAs | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.7 | InetAutonomousSystemNumber | read-only | Some implementations of BGP can represent themselves as multiple ASes. This is the AS that this peering session is representing itself as to the remote peer. |
| OID os10bgp4V2PeerLocalIdentifier | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.8 | Os10Bgp4V2IdentifierTC | read-only | The BGP Identifier of the local system for this peering session. It is REQUIRED that all os10bgp4V2PeerLocalIdentifier values for the same os10bgp4V2PeerInstance be identical. |
| INE os10bgp4V2PeerLocalPort | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.6 | InetPortNumber | read-only | The local port for the TCP connection between the BGP peers. |
| U32 os10bgp4V2PeerMinASOrigInterval | 1.3.6.1.4.1.674.11000.5000.200.1.1.5.1.4 | Unsigned32 | read-only | Time interval (in seconds) for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds. |
| U32 os10bgp4V2PeerMinRouteAdverInterval | 1.3.6.1.4.1.674.11000.5000.200.1.1.5.1.5 | Unsigned32 | read-only | Time interval (in seconds) for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds for EBGP connections and 5 seconds for IBGP connections. |
| os10bgp4V2PeerNegotiatedTimersEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.6.1 | not-accessible | Each entry reflects a value of the currently operational, negotiated timer as reflected in the Os10Bgp4V2PeerNegotiatedTimersEntry. | |
| os10bgp4V2PeerNegotiatedTimersTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.6 | not-accessible | Configured values of per-peer timers are seen in the os10bgp4V2PeerConfiguredTimersTable. Values in this table reflect the current operational values, after negotiation from values derived from initial configuration. | |
| C32 os10bgp4V2PeerOutTotalMessages | 1.3.6.1.4.1.674.11000.5000.200.1.1.7.1.4 | Counter32 | read-only | The total number of messages transmitted to the remote peer on this connection. |
| C32 os10bgp4V2PeerOutUpdates | 1.3.6.1.4.1.674.11000.5000.200.1.1.7.1.2 | Counter32 | read-only | The number of BGP UPDATE messages transmitted on this connection. |
| IP os10bgp4V2PeerRemoteAddr | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.5 | InetAddress | not-accessible | The remote IP address of this entry's BGP peer. |
| IPt os10bgp4V2PeerRemoteAddrType | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.4 | InetAddressType | not-accessible | The address family of the remote end of the peering session. An implementation is required to support IPv4 peering sessions in which case the length of this object is 4. An implementation MAY support IPv6 peering sessions in which case the length of this object is 16. IPv6 link-local peering sessions MAY be supported by this MIB. In this case the length of this object is 20. |
| INE os10bgp4V2PeerRemoteAs | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.10 | InetAutonomousSystemNumber | read-only | The remote autonomous system number received in the BGP OPEN message. |
| OID os10bgp4V2PeerRemoteIdentifier | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.11 | Os10Bgp4V2IdentifierTC | read-only | The BGP Identifier of this entry's remote BGP peer. This entry should be 0.0.0.0 unless the os10bgp4V2PeerState is in the openconfirm or the established state. |
| INE os10bgp4V2PeerRemotePort | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.9 | InetPortNumber | read-only | The remote port for the TCP connection between the BGP peers. Note that the objects os10bgp4V2PeerLocalAddr, os10bgp4V2PeerLocalPort, os10bgp4V2PeerRemoteAddr and os10bgp4V2PeerRemotePort provide the appropriate reference to the standard MIB TCP connection table, or even the ipv6 TCP MIB as in RFC 4022. |
| INT os10bgp4V2PeerState | 1.3.6.1.4.1.674.11000.5000.200.1.1.2.1.13 | INTEGER | read-only | The BGP peer connection state. |
| os10bgp4V2PeerTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.2 | not-accessible | BGP peer table. This table contains, one entry per BGP peer, information about the connections with BGP peers. | |
| ADR os10bgp4V2PrefixGaugesAfi | 1.3.6.1.4.1.674.11000.5000.200.1.1.8.1.1 | Os10Bgp4V2AddressFamilyIdentifierTC | not-accessible | The AFI index of the per-peer, per prefix counters |
| os10bgp4V2PrefixGaugesEntry | 1.3.6.1.4.1.674.11000.5000.200.1.1.8.1 | not-accessible | Entry containing information about a bgp-peers prefix counters. | |
| ADR os10bgp4V2PrefixGaugesSafi | 1.3.6.1.4.1.674.11000.5000.200.1.1.8.1.2 | Os10Bgp4V2SubsequentAddressFamilyIdentifierTC | not-accessible | The SAFI index of the per-peer, per prefix counters |
| os10bgp4V2PrefixGaugesTable | 1.3.6.1.4.1.674.11000.5000.200.1.1.8 | not-accessible | Additional per-peer, per AFI-SAFI counters for prefixes | |
| G32 os10bgp4V2PrefixInPrefixes | 1.3.6.1.4.1.674.11000.5000.200.1.1.8.1.3 | Gauge32 | read-only | The number of prefixes received from a peer and are stored in the Adj-Ribs-In for that peer. Note that this number does not reflect prefixes that have been discarded due to policy. |
| G32 os10bgp4V2PrefixInPrefixesAccepted | 1.3.6.1.4.1.674.11000.5000.200.1.1.8.1.4 | Gauge32 | read-only | The number of prefixes for a peer that are installed in the Adj-Ribs-In and are eligible to become active in the Loc-Rib. |
| G32 os10bgp4V2PrefixOutPrefixes | 1.3.6.1.4.1.674.11000.5000.200.1.1.8.1.5 | Gauge32 | read-only | The number of prefixes for a peer that are installed in that peer's Adj-Ribs-Out. |
RFC description
BGP-4 protocol management and monitoring for Dell EMC OS10 switches.
Start monitoring Dell EMC switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.