DELL-NETWORKING-BGP4-V2-MIB

All MIBs › DELL-NETWORKING-BGP4-V2-MIB

Organization: IETF IDR Working Group

Last Updated: 2007-04-27

Category: Routing Protocols, Vendor: Dell

Description: Handles routing policy and peer session management for BGP4 version 2 on Dell Networking switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DELL-NETWORKING-BGP4-V2-MIB?

This MIB module manages Border Gateway Protocol version 4 (BGP4) routing objects for Dell Networking switches, covering peer session establishment, routing policy, and route exchange state for the BGP protocol used in large-scale IP routing. Although no sample objects were provided, a BGP4 MIB of this type typically exposes peer state (idle, connect, established, etc.), negotiated capabilities, path attributes, and route counts per peer. Its monitoring value lies in tracking BGP control-plane software health—detecting peer session flaps, unexpected state transitions, or route count anomalies that indicate routing instability—rather than hardware sensor data. It is explicitly modeled on and closely related to the standard IETF BGP4-MIB, extended/versioned for Dell's platform. It would be deployed on Dell Networking switches and routers acting as BGP speakers in data center or enterprise WAN routing environments. Engineers implementing or auditing this functionality typically reference the DELL-NETWORKING-BGP4-V2-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in DELL-NETWORKING-BGP4-V2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Dell Networking switch/router

Monitoring Examples

No sample objects were included for this MIB, so specific table/object names cannot be cited directly; however, based on the standard BGP4-MIB this module extends, an operator would typically poll a peer table for per-peer administrative and operational state (e.g., idle vs. established) and received/advertised route counts. A peer unexpectedly transitioning out of the established state, or a sharp drop in received routes, would signal a BGP session failure or upstream routing issue. Confirming exact object names would require consulting the actual MIB source.

What Can Be Monitored

BGP peer session state
BGP peer negotiated capabilities
route counts per peer
session state transitions

Imported Objects

From DELL-NETWORKING-SMI

dellNetExperiment

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressPrefixLength
InetAddressType
InetAutonomousSystemNumber
InetPortNumber

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32
mib-2

From SNMPv2-TC

RowPointer
RowStatus
StorageType
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using dellNetBgpM2PathAttrCount OID:

Select a Dell Networking switch/router (BGP4) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type dellNetBgpM2PathAttrCount into the Find box to locate it in the OID tree, then select it and click OK. The number of entries in the dellNetBgpM2PathAttrTable. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
dellNetBgpM2	1.3.6.1.4.1.6027.20.1			This MIB module defines management objects for the Border Gateway Protocol, Version 4.
dellNetBgpM2BaseScalars	1.3.6.1.4.1.6027.20.1.1
dellNetBgpM2BaseNotifications	1.3.6.1.4.1.6027.20.1.1.0
NTF dellNetBgpM2Established	1.3.6.1.4.1.6027.20.1.1.0.1			The BGP Established event is generated when the BGP FSM enters the ESTABLISHED state.
NTF dellNetBgpM2BackwardTransition	1.3.6.1.4.1.6027.20.1.1.0.2			The BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state.
dellNetBgpM2Version	1.3.6.1.4.1.6027.20.1.1.1
dellNetBgpM2VersionTable	1.3.6.1.4.1.6027.20.1.1.1.1		not-accessible	Table of supported BGP versions.
dellNetBgpM2VersionEntry	1.3.6.1.4.1.6027.20.1.1.1.1.1		not-accessible	Entry containing data on a given supported version of the Border Gateway Protocol and the level of support provided. It is expected that any agent implementation supporting this MIB module will report support for Version 4 of the Border Gateway Protocol at the very minimum.
U32 dellNetBgpM2VersionIndex	1.3.6.1.4.1.6027.20.1.1.1.1.1.1	Unsigned32	read-only	The version number of the BGP Protocol.
T/F dellNetBgpM2VersionSupported	1.3.6.1.4.1.6027.20.1.1.1.1.1.2	TruthValue	read-only	This value is TRUE if this version of the BGP protocol identified in 'dellNetBgpM2VersionIndex' is supported. The absence of a row for a particular dellNetBgpM2VersionIndex indicates that that dellNetBgpM2VersionIndex protocol version number is not supported.
dellNetBgpM2SupportedCapabilities	1.3.6.1.4.1.6027.20.1.1.2
T/F dellNetBgpM2CapabilitySupportAvailable	1.3.6.1.4.1.6027.20.1.1.2.1	TruthValue	read-only	This value is TRUE if capability support is available and is enabled.
dellNetBgpM2SupportedCapabilitiesTable	1.3.6.1.4.1.6027.20.1.1.2.2		not-accessible	Table of supported BGP-4 capabilities.
dellNetBgpM2SupportedCapabilitiesEntry	1.3.6.1.4.1.6027.20.1.1.2.2.1		not-accessible	Information about supported capabilities indexed by capability number.
U32 dellNetBgpM2SupportedCapabilityCode	1.3.6.1.4.1.6027.20.1.1.2.2.1.1	Unsigned32	read-only	Index of supported capability. The index directly corresponds with the BGP-4 Capability Advertisement Capability Code.
T/F dellNetBgpM2SupportedCapability	1.3.6.1.4.1.6027.20.1.1.2.2.1.2	TruthValue	read-only	This value is True if this capability is supported, False otherwise.
INT dellNetBgpM2AsSize	1.3.6.1.4.1.6027.20.1.1.4	INTEGER	read-only	The size of the AS value in this implementation. The semantics of this are determined as per the as-4bytes draft.
INE dellNetBgpM2LocalAs	1.3.6.1.4.1.6027.20.1.1.5	InetAutonomousSystemNumber	read-only	The local autonomous system number. If the dellNetBgpM2AsSize is twoOctet, then the range is constrained to be 0-65535.
OID dellNetBgpM2LocalIdentifier	1.3.6.1.4.1.6027.20.1.1.6	DellNetBgpM2Identifier	read-only	The BGP Identifier of local system. Current practice is trending away from this value being treated as an IP address and more as a generic identifier.
dellNetBgpM2BaseScalarExtensions	1.3.6.1.4.1.6027.20.1.1.7
dellNetBgpM2BaseScalarNonCapExts	1.3.6.1.4.1.6027.20.1.1.7.1
dellNetBgpM2BaseScalarRouteReflectExts	1.3.6.1.4.1.6027.20.1.1.7.1.2796
T/F dellNetBgpM2RouteReflector	1.3.6.1.4.1.6027.20.1.1.7.1.2796.1	TruthValue	read-only	This value is TRUE if this implementation supports the BGP Route Reflection Extension and is enabled as a route reflector. If the BGP Route Reflection extension is not supported this value must be FALSE.
OID dellNetBgpM2ClusterId	1.3.6.1.4.1.6027.20.1.1.7.1.2796.2	DellNetBgpM2Identifier	read-only	The configured Cluster-ID of the BGP Speaker. This will default to the BGP Speaker's DellNetBgpM2Identifier if this speaker is functioning as a route reflector and an explicit Cluster-ID has not been configured. A value of 0.0.0.0 will be present if Route Reflection is not enabled.
dellNetBgpM2BaseScalarASConfedExts	1.3.6.1.4.1.6027.20.1.1.7.1.3065
T/F dellNetBgpM2ConfederationRouter	1.3.6.1.4.1.6027.20.1.1.7.1.3065.1	TruthValue	read-only	This value is TRUE if this implementation supports the BGP AS Confederations Extension and this router is configured to be in a confederation.
INE dellNetBgpM2ConfederationId	1.3.6.1.4.1.6027.20.1.1.7.1.3065.2	InetAutonomousSystemNumber	read-only	The local Confederation Identification Number. This value will be zero (0) if this BGP Speaker is not a confederation router.
dellNetBgpM2BaseScalarCapExts	1.3.6.1.4.1.6027.20.1.1.7.2
dellNetBgpM2BaseScalarConfiguration	1.3.6.1.4.1.6027.20.1.1.8
STO dellNetBgpM2CfgBaseScalarStorageType	1.3.6.1.4.1.6027.20.1.1.8.1	StorageType	read-write	This object specifies the intended storage type for all configurable base scalars.
INE dellNetBgpM2CfgLocalAs	1.3.6.1.4.1.6027.20.1.1.8.2	InetAutonomousSystemNumber	read-write	The local autonomous system number. If the dellNetBgpM2AsSize is twoOctet, then the range is constrained to be 0-65535.
OID dellNetBgpM2CfgLocalIdentifier	1.3.6.1.4.1.6027.20.1.1.8.3	DellNetBgpM2Identifier	read-write	The BGP Identifier of local system. Current practice is trending away from this value being treated as an IP address and more as a generic identifier.
dellNetBgpM2CfgBaseScalarExtensions	1.3.6.1.4.1.6027.20.1.1.8.4
dellNetBgpM2CfgBaseScalarNonCapExts	1.3.6.1.4.1.6027.20.1.1.8.4.1
dellNetBgpM2CfgBaseScalarReflectorExts	1.3.6.1.4.1.6027.20.1.1.8.4.1.2796
T/F dellNetBgpM2CfgRouteReflector	1.3.6.1.4.1.6027.20.1.1.8.4.1.2796.1	TruthValue	read-write	This value is set to true if this implementation will be supporting route reflection.
OID dellNetBgpM2CfgClusterId	1.3.6.1.4.1.6027.20.1.1.8.4.1.2796.2	DellNetBgpM2Identifier	read-write	The configured Cluster-ID of the BGP Speaker. This will default to the BGP Speaker's DellNetBgpM2Identifier if this speaker is functioning as a route reflector and an explicit Cluster-ID has not been configured. A value of 0.0.0.0 will be present if Route Reflection is not enabled.
dellNetBgpM2CfgBaseScalarASConfedExts	1.3.6.1.4.1.6027.20.1.1.8.4.1.3065
T/F dellNetBgpM2CfgConfederationRouter	1.3.6.1.4.1.6027.20.1.1.8.4.1.3065.1	TruthValue	read-write	This value is set to true if this implementation will be supporting BGP AS Confederations.
INE dellNetBgpM2CfgConfederationId	1.3.6.1.4.1.6027.20.1.1.8.4.1.3065.2	InetAutonomousSystemNumber	read-write	The local Confederation Identification Number. This value will be zero (0) if this BGP Speaker is not a confederation router.
dellNetBgpM2CfgBaseScalarCapExts	1.3.6.1.4.1.6027.20.1.1.8.4.2
dellNetBgpM2Peer	1.3.6.1.4.1.6027.20.1.2
dellNetBgpM2PeerData	1.3.6.1.4.1.6027.20.1.2.1
dellNetBgpM2PeerTable	1.3.6.1.4.1.6027.20.1.2.1.1		not-accessible	BGP peer table. This table contains, one entry per remote BGP peer, any information about the connections with the remote BGP peers.
dellNetBgpM2PeerEntry	1.3.6.1.4.1.6027.20.1.2.1.1.1		not-accessible	Entry containing information about the connection with a remote BGP peer.
U32 dellNetBgpM2PeerInstance	1.3.6.1.4.1.6027.20.1.2.1.1.1.1	Unsigned32	read-only	The routing instance index. Some BGP implementations permit the creation of multiple instances of a BGP routing process. An example includes RFC 2547 PE-CE routers. Implementations that do not support multiple routing instances should return 1 for this object. XXX TODO - We need to provide a way to configure these in the peer configuration table.
OID dellNetBgpM2PeerIdentifier	1.3.6.1.4.1.6027.20.1.2.1.1.1.2	DellNetBgpM2Identifier	read-only	The BGP Identifier of this entry's remote BGP peer. This entry should be 0.0.0.0 unless the dellNetBgpM2PeerState is in the OpenConfirm or the Established state.
INT dellNetBgpM2PeerState	1.3.6.1.4.1.6027.20.1.2.1.1.1.3	INTEGER	read-only	The remote BGP peer's FSM state.
INT dellNetBgpM2PeerStatus	1.3.6.1.4.1.6027.20.1.2.1.1.1.4	INTEGER	read-only	Whether or not the BGP FSM for this remote peer is halted or running. The BGP FSM for a remote peer is halted after processing a Stop event. Likewise, it is in the running state after a Start event. The dellNetBgpM2PeerState will generally be in the idle state when the FSM is halted, although some extensions such as Graceful Restart will leave the peer in the Idle state but with the FSM running.
U32 dellNetBgpM2PeerConfiguredVersion	1.3.6.1.4.1.6027.20.1.2.1.1.1.5	Unsigned32	read-only	The configured version to originally start with this remote peer. The BGP speaker may permit negotiation to a lower version number of the protocol.
U32 dellNetBgpM2PeerNegotiatedVersion	1.3.6.1.4.1.6027.20.1.2.1.1.1.6	Unsigned32	read-only	The negotiated version of BGP running between the two peers.
IPt dellNetBgpM2PeerLocalAddrType	1.3.6.1.4.1.6027.20.1.2.1.1.1.7	InetAddressType	read-only	The address family of the local end of the peering session.
IP dellNetBgpM2PeerLocalAddr	1.3.6.1.4.1.6027.20.1.2.1.1.1.8	InetAddress	read-only	The address of the local end of the peering session.
INE dellNetBgpM2PeerLocalPort	1.3.6.1.4.1.6027.20.1.2.1.1.1.9	InetPortNumber	read-only	The local port for the TCP connection between the BGP peers.
INE dellNetBgpM2PeerLocalAs	1.3.6.1.4.1.6027.20.1.2.1.1.1.10	InetAutonomousSystemNumber	read-only	Some implementations of BGP can represent themselves as multiple ASs. This is the AS that this peering session is representing itself as to the remote peer.
IPt dellNetBgpM2PeerRemoteAddrType	1.3.6.1.4.1.6027.20.1.2.1.1.1.11	InetAddressType	read-only	The address family of the remote end of the peering session.
IP dellNetBgpM2PeerRemoteAddr	1.3.6.1.4.1.6027.20.1.2.1.1.1.12	InetAddress	read-only	The address of the remote end of the peering session.
INE dellNetBgpM2PeerRemotePort	1.3.6.1.4.1.6027.20.1.2.1.1.1.13	InetPortNumber	read-only	The remote port for the TCP connection between the BGP peers. In the case of a transport for which the notion of 'port' is irrelevant, an instance value of -1 should be returned by the agent for this object. Note that the objects dellNetBgpM2PeerLocalAddr, dellNetBgpM2PeerLocalPort, dellNetBgpM2PeerRemoteAddr and dellNetBgpM2PeerRemotePort provide the appropriate reference to the standard MIB TCP connection table. or even the ipv6 TCP MIB as in rfc2452.
INE dellNetBgpM2PeerRemoteAs	1.3.6.1.4.1.6027.20.1.2.1.1.1.14	InetAutonomousSystemNumber	read-only	The remote autonomous system number.
U32 dellNetBgpM2PeerIndex	1.3.6.1.4.1.6027.20.1.2.1.1.1.15	Unsigned32	read-only	This value is a unique index for the remote peer entry in the dellNetBgpM2PeerTable. It is assigned by the agent at the point of creation of the dellNetBgpM2PeerTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of dellNetBgpM2PeerIndex row instance values across rows of the dellNetBgpM2PeerTable. It is used to provide an index structure for other tables whose data is logically per-peer. For explicitly configured peers, this value will remain consistent until this row is deleted by deleting the configured peers. Unconfigured peers will generate a monotonically increasing number when a BGP FSM is built to process the peering session. Values in the dellNetBgpM2PeerTable and other tables utilizing dellNetBgpM2PeerIndex are expected to remain in existence for an arbitrary time after the unconfigured peer has been deleted in order to allow management applications to extract useful management information for those peers. Thus, an unconfigured peer using the same indices as the dellNetBgpM2PeerTable that comes up while this row still exists will re-utilize the same row.
dellNetBgpM2PeerErrors	1.3.6.1.4.1.6027.20.1.2.2
dellNetBgpM2PeerErrorsTable	1.3.6.1.4.1.6027.20.1.2.2.1		not-accessible	On a per peer basis, this table reflects the last protocol-defined error encountered and reported on the peer session. If no entry for a given peer, by its dellNetBgpM2PeerIndex, exists in this table, then no such errors have been observed, reported, and recorded on the session.
dellNetBgpM2PeerErrorsEntry	1.3.6.1.4.1.6027.20.1.2.2.1.1		not-accessible	Each entry contains information about errors sent and received for a particular BGP peer.
OCT dellNetBgpM2PeerLastErrorReceived	1.3.6.1.4.1.6027.20.1.2.2.1.1.1	OCTET STRING	read-only	The last error code and subcode received by this BGP Speaker via a NOTIFICATION message for this peer. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.
OCT dellNetBgpM2PeerLastErrorSent	1.3.6.1.4.1.6027.20.1.2.2.1.1.2	OCTET STRING	read-only	The last error code and subcode sent by this BGP Speaker via a NOTIFICATION message to this peer. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.
TIK dellNetBgpM2PeerLastErrorReceivedTime	1.3.6.1.4.1.6027.20.1.2.2.1.1.3	TimeTicks	read-only	The timestamp that the last NOTIFICATION was received from this peer.
TIK dellNetBgpM2PeerLastErrorSentTime	1.3.6.1.4.1.6027.20.1.2.2.1.1.4	TimeTicks	read-only	The timestamp that the last NOTIFICATION was sent to this peer.
STR dellNetBgpM2PeerLastErrorReceivedText	1.3.6.1.4.1.6027.20.1.2.2.1.1.5	SnmpAdminString	read-only	This object contains an implementation specific explanation of the error that was reported.
STR dellNetBgpM2PeerLastErrorSentText	1.3.6.1.4.1.6027.20.1.2.2.1.1.6	SnmpAdminString	read-only	This object contains an implementation specific explanation of the error that is being reported.
OCT dellNetBgpM2PeerLastErrorReceivedData	1.3.6.1.4.1.6027.20.1.2.2.1.1.7	OCTET STRING	read-only	The last error code's data seen by this peer.
OCT dellNetBgpM2PeerLastErrorSentData	1.3.6.1.4.1.6027.20.1.2.2.1.1.8	OCTET STRING	read-only	The last error code's data sent to this peer.
dellNetBgpM2PeerTimers	1.3.6.1.4.1.6027.20.1.2.3
dellNetBgpM2PeerEventTimesTable	1.3.6.1.4.1.6027.20.1.2.3.1		not-accessible	A table reporting the per-peering session amount of time elapsed and update events since the peering session advanced into the Established state.
dellNetBgpM2PeerEventTimesEntry	1.3.6.1.4.1.6027.20.1.2.3.1.1		not-accessible	Each row contains a set of statistics about time spent and events encountered in the peer session Established state.
G32 dellNetBgpM2PeerFsmEstablishedTime	1.3.6.1.4.1.6027.20.1.2.3.1.1.1	Gauge32	read-only	This timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set to zero when a new peer is configured or the router is booted.
G32 dellNetBgpM2PeerInUpdatesElapsedTime	1.3.6.1.4.1.6027.20.1.2.3.1.1.2	Gauge32	read-only	Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time dellNetBgpM2PeerInUpdates is incremented, the value of this object is set to zero (0). This value shall also be zero (0) when the peer is not in the Established state
dellNetBgpM2PeerConfiguredTimersTable	1.3.6.1.4.1.6027.20.1.2.3.2		not-accessible	Per peer management data on BGP session timers.
dellNetBgpM2PeerConfiguredTimersEntry	1.3.6.1.4.1.6027.20.1.2.3.2.1		not-accessible	Each entry corresponds to the current state of BGP timers on a given peering session.
U32 dellNetBgpM2PeerConnectRetryInterval	1.3.6.1.4.1.6027.20.1.2.3.2.1.1	Unsigned32	read-only	Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
U32 dellNetBgpM2PeerHoldTimeConfigured	1.3.6.1.4.1.6027.20.1.2.3.2.1.2	Unsigned32	read-only	Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (dellNetBgpM2PeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.
U32 dellNetBgpM2PeerKeepAliveConfigured	1.3.6.1.4.1.6027.20.1.2.3.2.1.3	Unsigned32	read-only	Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages frequency relative to the value specified in dellNetBgpM2PeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by dellNetBgpM2PeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of dellNetBgpM2PeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
U32 dellNetBgpM2PeerMinASOrigInterval	1.3.6.1.4.1.6027.20.1.2.3.2.1.4	Unsigned32	read-only	Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds.
U32 dellNetBgpM2PeerMinRouteAdverInterval	1.3.6.1.4.1.6027.20.1.2.3.2.1.5	Unsigned32	read-only	Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.
dellNetBgpM2PeerNegotiatedTimersTable	1.3.6.1.4.1.6027.20.1.2.3.3		not-accessible	Current values of per-peer timers which can be dynamically set in the dellNetBgpM2PeerConfiguredTimersTable. Values reflected in this table are the current operational values, after negotiation from values derived from initial configuration or last set from dellNetBgpM2PeerConfiguredTimersTable row instances.
dellNetBgpM2PeerNegotiatedTimersEntry	1.3.6.1.4.1.6027.20.1.2.3.3.1		not-accessible	Each entry reflects a value of the currently operational, negotiated timers as reflected in the DellNetBgpM2PeerNegotiatedTimersEntry.
U32 dellNetBgpM2PeerHoldTime	1.3.6.1.4.1.6027.20.1.2.3.3.1.1	Unsigned32	read-only	The value of this object is calculated by this BGP Speaker as being; zero (0) - if this was the value sent by the peer and this value is permitted by this BGP Speaker. In this case, no keepalive messages are sent and the Hold Timer is not set. At least three (3). This value is the smaller of the value sent by this peer in the OPEN message and dellNetBgpM2PeerHoldTimeConfigured for this peer. This value is only defined when the peering session is in the Established state.
U32 dellNetBgpM2PeerKeepAlive	1.3.6.1.4.1.6027.20.1.2.3.3.1.2	Unsigned32	read-only	Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with dellNetBgpM2PeerHoldTime, it has the same proportion as what dellNetBgpM2PeerKeepAliveConfigured has when compared with dellNetBgpM2PeerHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of dellNetBgpM2PeerKeepAliveConfigured is zero (0). This value is only defined when the peering session is in the Established state.
dellNetBgpM2PeerCapabilities	1.3.6.1.4.1.6027.20.1.2.4
dellNetBgpM2PeerCapsAnnouncedTable	1.3.6.1.4.1.6027.20.1.2.4.1		not-accessible	This table contains the capabilities that are supported for a given peer.
dellNetBgpM2PeerCapsAnnouncedEntry	1.3.6.1.4.1.6027.20.1.2.4.1.1		not-accessible	These entries are keyed by a BGP-4 peer remote address and the BGP Capability Code
U32 dellNetBgpM2PeerCapAnnouncedCode	1.3.6.1.4.1.6027.20.1.2.4.1.1.1	Unsigned32	read-only	The BGP Capability Advertisement Capability Code.
U32 dellNetBgpM2PeerCapAnnouncedIndex	1.3.6.1.4.1.6027.20.1.2.4.1.1.2	Unsigned32	read-only	Multiple instances of a given capability may be sent bgp a BGP speaker. This variable is used to index them.
OCT dellNetBgpM2PeerCapAnnouncedValue	1.3.6.1.4.1.6027.20.1.2.4.1.1.3	OCTET STRING	read-only	The value of the announced capability.
dellNetBgpM2PeerCapsReceivedTable	1.3.6.1.4.1.6027.20.1.2.4.2		not-accessible	This table contains the capabilities that are supported for a given peer.
dellNetBgpM2PeerCapsReceivedEntry	1.3.6.1.4.1.6027.20.1.2.4.2.1		not-accessible	These entries are keyed by a BGP-4 peer remote address and the BGP Capability Code
U32 dellNetBgpM2PeerCapReceivedCode	1.3.6.1.4.1.6027.20.1.2.4.2.1.1	Unsigned32	read-only	The BGP Capability Advertisement Capability Code.
U32 dellNetBgpM2PeerCapReceivedIndex	1.3.6.1.4.1.6027.20.1.2.4.2.1.2	Unsigned32	read-only	Multiple instances of a given capability may be sent bgp a BGP speaker. This variable is used to index them.
OCT dellNetBgpM2PeerCapReceivedValue	1.3.6.1.4.1.6027.20.1.2.4.2.1.3	OCTET STRING	read-only	The value of the announced capability.
dellNetBgpM2PeerCounters	1.3.6.1.4.1.6027.20.1.2.6
dellNetBgpM2PeerCountersTable	1.3.6.1.4.1.6027.20.1.2.6.1		not-accessible	The counters associated with a BGP Peer.
dellNetBgpM2PeerCountersEntry	1.3.6.1.4.1.6027.20.1.2.6.1.1		not-accessible	Each entry contains counters of message transmissions and FSM transitions for a given BGP Peering session.
C32 dellNetBgpM2PeerInUpdates	1.3.6.1.4.1.6027.20.1.2.6.1.1.1	Counter32	read-only	The number of BGP UPDATE messages received on this connection. This object should be initialized to zero (0) when the connection is established.
C32 dellNetBgpM2PeerOutUpdates	1.3.6.1.4.1.6027.20.1.2.6.1.1.2	Counter32	read-only	The number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero (0) when the connection is established.
C32 dellNetBgpM2PeerInTotalMessages	1.3.6.1.4.1.6027.20.1.2.6.1.1.3	Counter32	read-only	The total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established.
C32 dellNetBgpM2PeerOutTotalMessages	1.3.6.1.4.1.6027.20.1.2.6.1.1.4	Counter32	read-only	The total number of messages transmitted to the remote peer on this connection. This object should be initialized to zero when the connection is established.
C32 dellNetBgpM2PeerFsmEstablishedTrans	1.3.6.1.4.1.6027.20.1.2.6.1.1.5	Counter32	read-only	The total number of times the BGP FSM transitioned into the established state for this peer.
C32 dellNetBgpM2PeerInKeepalives	1.3.6.1.4.1.6027.20.1.2.6.1.1.6	Counter32	read-only	The number of Keepalive messages received from a peer.Implemented by Dell.
C32 dellNetBgpM2PeerOutKeepalives	1.3.6.1.4.1.6027.20.1.2.6.1.1.7	Counter32	read-only	The number of Keepalive messages sent to a peer. Implemented by Dell.
C32 dellNetBgpM2PeerInOpen	1.3.6.1.4.1.6027.20.1.2.6.1.1.8	Counter32	read-only	The number of Open messages received from a peer. Implemented by Dell.
C32 dellNetBgpM2PeerOutOpen	1.3.6.1.4.1.6027.20.1.2.6.1.1.9	Counter32	read-only	The number of Open messages sent to a peer. Implemented by Dell.
C32 dellNetBgpM2PeerInRteRefresh	1.3.6.1.4.1.6027.20.1.2.6.1.1.10	Counter32	read-only	The number of Route Refresh messages received from a peer. Implemented by Dell.
C32 dellNetBgpM2PeerOutRteRefresh	1.3.6.1.4.1.6027.20.1.2.6.1.1.11	Counter32	read-only	The number of Route Refresh messages sent to a peer. Implemented by Dell.
dellNetBgpM2PrefixCountersTable	1.3.6.1.4.1.6027.20.1.2.6.2		not-accessible	Additional per-peer, per AFI SAFI counters for prefixes
dellNetBgpM2PrefixCountersEntry	1.3.6.1.4.1.6027.20.1.2.6.2.1		not-accessible	Entry containing information about a bgp-peers prefix counters.
DEL dellNetBgpM2PrefixCountersAfi	1.3.6.1.4.1.6027.20.1.2.6.2.1.1	DellNetBgpM2Afi	read-only	The AFI index of the per-peer, per prefix counters
DEL dellNetBgpM2PrefixCountersSafi	1.3.6.1.4.1.6027.20.1.2.6.2.1.2	DellNetBgpM2Safi	read-only	The SAFI index of the per-peer, per prefix counters
G32 dellNetBgpM2PrefixInPrefixes	1.3.6.1.4.1.6027.20.1.2.6.2.1.7	Gauge32	read-only	The number of prefixes received from a peer and are stored in the Adj-Ribs-In for that peer.
G32 dellNetBgpM2PrefixInPrefixesAccepted	1.3.6.1.4.1.6027.20.1.2.6.2.1.8	Gauge32	read-only	The number of prefixes for a peer that are installed in the Adj-Ribs-In and are eligible to become active in the Loc-Rib.
G32 dellNetBgpM2PrefixInPrefixesRejected	1.3.6.1.4.1.6027.20.1.2.6.2.1.9	Gauge32	read-only	The number of prefixes for a peer that are installed in the Adj-Ribs-In and are NOT eligible to become active in the Loc-Rib.
G32 dellNetBgpM2PrefixOutPrefixes	1.3.6.1.4.1.6027.20.1.2.6.2.1.10	Gauge32	read-only	The number of prefixes for a peer that are installed in that peers Adj-Ribs-Out.
G32 dellNetBgpM2PrefixWdrawnByPeer	1.3.6.1.4.1.6027.20.1.2.6.2.1.11	Gauge32	read-only	The number of prefixes withdrawn by a peer. Implemened by Dell.
G32 dellNetBgpM2PrefixWdrawnFromPeer	1.3.6.1.4.1.6027.20.1.2.6.2.1.12	Gauge32	read-only	The number of prefixes withdrawn from a peer. Implemened by Dell.
dellNetBgpM2PeerExtensions	1.3.6.1.4.1.6027.20.1.2.7
dellNetBgpM2PeerNonCapExts	1.3.6.1.4.1.6027.20.1.2.7.1
dellNetBgpM2PeerRouteReflectionExts	1.3.6.1.4.1.6027.20.1.2.7.1.2796
dellNetBgpM2PeerReflectorClientTable	1.3.6.1.4.1.6027.20.1.2.7.1.2796.1		not-accessible	Table of route reflection client settings on a per-peer basis.
dellNetBgpM2PeerReflectorClientEntry	1.3.6.1.4.1.6027.20.1.2.7.1.2796.1.1		not-accessible	Entry containing data on a per-peer basis on whether the peer is configured as a route reflector client.
INT dellNetBgpM2PeerReflectorClient	1.3.6.1.4.1.6027.20.1.2.7.1.2796.1.1.1	INTEGER	read-only	This value indicates whether the given peer is a reflector client of this router, or not. A value of nonClient indicates that this peer is not a reflector client. A value of client indicates that this peer is a reflector client that is not fully meshed with other reflector clients. A value of meshedClient indicates that the peer is a reflector client and is fully meshed with all other reflector clients. This value must be nonClient (0) for BGP external peers.
dellNetBgpM2PeerASConfederationExts	1.3.6.1.4.1.6027.20.1.2.7.1.3065
dellNetBgpM2PeerConfedMemberTable	1.3.6.1.4.1.6027.20.1.2.7.1.3065.1		not-accessible	Table of confederation member settings on a per-peer basis.
dellNetBgpM2PeerConfedMemberEntry	1.3.6.1.4.1.6027.20.1.2.7.1.3065.1.1		not-accessible	Entry containing data on a per-peer basis on whether the peer is configured as a BGP confederation member.
T/F dellNetBgpM2PeerConfedMember	1.3.6.1.4.1.6027.20.1.2.7.1.3065.1.1.1	TruthValue	read-only	This value indicates whether the given peer is in our confederation or not.
dellNetBgpM2PeerCapExts	1.3.6.1.4.1.6027.20.1.2.7.2
dellNetBgpM2PeerConfiguration	1.3.6.1.4.1.6027.20.1.2.8
dellNetBgpM2CfgPeerAdminStatusTable	1.3.6.1.4.1.6027.20.1.2.8.1		not-accessible	Table containing rows for administratively starting and stopping peering sessions.
dellNetBgpM2CfgPeerAdminStatusEntry	1.3.6.1.4.1.6027.20.1.2.8.1.1		not-accessible	Entry containing row for administratively starting and stopping peers.
INT dellNetBgpM2CfgPeerAdminStatus	1.3.6.1.4.1.6027.20.1.2.8.1.1.1	INTEGER	read-write	This object allows the Manual Stop and Manual Start events to be sent to an activated peering session.
I32 dellNetBgpM2CfgPeerNextIndex	1.3.6.1.4.1.6027.20.1.2.8.2	Integer32	read-only	This object contains the next appropriate value to use as an index for creation of a row instance in in the dellNetBgpM2CfgPeerTable. If the number of available entries in the dellNetBgpM2CfgPeerTable is exhausted, a retrieval value of this object instance will return 0. A value of 0 may also be returned if the agent is otherwise incapable of dellNetBgpM2CfgPeerTable row creation at the time of dellNetBgpM2CfgPeerNextIndex retrieval.
dellNetBgpM2CfgPeerTable	1.3.6.1.4.1.6027.20.1.2.8.3		not-accessible	BGP configuration peer table. This table allows the configuration of the parameters for a session with a BGP peer. +++wayne provide description of how config should be done for a peer per table.
dellNetBgpM2CfgPeerEntry	1.3.6.1.4.1.6027.20.1.2.8.3.1		not-accessible	Entry containing information set up by a management entity to configure a connection with a BGP peer.
U32 dellNetBgpM2CfgPeerConfiguredVersion	1.3.6.1.4.1.6027.20.1.2.8.3.1.1	Unsigned32	read-create	The configured version to originally start with this peer. The BGP speaker may permit negotiation to a lower version number of the protocol depending on the set value of dellNetBgpM2CfgAllowVersionNegotiation.
T/F dellNetBgpM2CfgAllowVersionNegotiation	1.3.6.1.4.1.6027.20.1.2.8.3.1.2	TruthValue	read-create	If set to true, during session establishment with this peer, negotiation to a version lower than that specified in dellNetBgpM2CfgPeerConfiguredVersion will be allowed.
IPt dellNetBgpM2CfgPeerLocalAddrType	1.3.6.1.4.1.6027.20.1.2.8.3.1.3	InetAddressType	read-create	The address family of the speakers of this BGP session.
IP dellNetBgpM2CfgPeerLocalAddr	1.3.6.1.4.1.6027.20.1.2.8.3.1.4	InetAddress	read-create	The address of the local end of the peering session.
INE dellNetBgpM2CfgPeerLocalAs	1.3.6.1.4.1.6027.20.1.2.8.3.1.5	InetAutonomousSystemNumber	read-create	Autonomous system represented to peer on peering session initialization. Some implementations of BGP can represent themselves as multiple ASes. These implementations can set this to an alternate autonomous system. If this object is set to zero (0) at the point this row instance is set to active, then the implementation will initialize this session representing itself as the value of dellNetBgpM2CfgLocalAs.
IPt dellNetBgpM2CfgPeerRemoteAddrType	1.3.6.1.4.1.6027.20.1.2.8.3.1.6	InetAddressType	read-create	The address family of the speakers of the remote BGP session.
IP dellNetBgpM2CfgPeerRemoteAddr	1.3.6.1.4.1.6027.20.1.2.8.3.1.7	InetAddress	read-create	The address of the remote end (destination address of peer) for peering session.
INE dellNetBgpM2CfgPeerRemoteAs	1.3.6.1.4.1.6027.20.1.2.8.3.1.8	InetAutonomousSystemNumber	read-create	Autonomous system number of the remote peer.
STO dellNetBgpM2CfgPeerEntryStorageType	1.3.6.1.4.1.6027.20.1.2.8.3.1.9	StorageType	read-create	This object type specifies the intended storage type for the dellNetBgpM2CfgPeerEntry row instance.
INT dellNetBgpM2CfgPeerError	1.3.6.1.4.1.6027.20.1.2.8.3.1.10	INTEGER	read-only	This value indicates the current error status of the row denoting the configured error status. If this row is still under creation (has not been activated dellNetBgpM2CfgPeerRowEntryStatus), then this instance will be set to not-activated (1). At the point that the row is activated, dellNetBgpM2CfgPeerError will reflect the error status of the row data itself. If there is another session already activated with the same local and remote addresses as denoted by {dellNetBgpM2CfgPeerLocalAddrType, dellNetBgpM2CfgPeerLocalAddr, dellNetBgpM2CfgPeerRemoteAddr}, then the value of this will be set to err-duplicate-peering-session (2). If this row is associated with a peer session whose initialization has been attempted, the value will be set to activated (3) (and, dellNetBgpM2PeerCfgPeerEntry will be set to the row instance of the entry in the dellNetBgpM2PeerTable which reflects the state of the peering session). Note that this object only reflects the error as a function of the attempted activation of this row as containing data for a bgp peering session. The actual state of the session at the point of any protocol exchange or session state machine initiation is reflected in the dellNetBgpM2PeerTable row instance (as reflected through dellNetBgpM2CfgPeerPeerEntry) associated with this row instance.
NUM dellNetBgpM2CfgPeerBgpPeerEntry	1.3.6.1.4.1.6027.20.1.2.8.3.1.11	RowPointer	read-only	Upon activation of the session data contained in this row instance, this object points to an instance of a row within the dellNetBgpM2PeerTable reflecting the session in its initializing or operational state. Retrieval of this column instance will always yield a value of {0.0} unless the session has successfully been activated (via dellNetBgpM2CfgPeerRowEntryStatus). Such row instances will always have a value of dellNetBgpM2CfgPeerError which is activated (3).
ROW dellNetBgpM2CfgPeerRowEntryStatus	1.3.6.1.4.1.6027.20.1.2.8.3.1.12	RowStatus	read-create	This object type is used to control creation, activation, and deletion of this row instance.
I32 dellNetBgpM2CfgPeerIndex	1.3.6.1.4.1.6027.20.1.2.8.3.1.13	Integer32	accessible-for-notify	Uniquely identifies an instance of a peer row, as an element of configuration.
INT dellNetBgpM2CfgPeerStatus	1.3.6.1.4.1.6027.20.1.2.8.3.1.14	INTEGER	read-create	This specifies the state of the peering session upon activation. If disabled, the FSM is in the halted state and no Automatic Start events are generated. If enabled, the FSM is in the running state and Automatic Start events may be generated.
dellNetBgpM2CfgPeerTimersTable	1.3.6.1.4.1.6027.20.1.2.8.4		not-accessible	Table for configuration of per-peer timers.
dellNetBgpM2CfgPeerTimersEntry	1.3.6.1.4.1.6027.20.1.2.8.4.1		not-accessible	Entry containing per-peer timer configuration.
U32 dellNetBgpM2CfgPeerConnectRetryInterval	1.3.6.1.4.1.6027.20.1.2.8.4.1.1	Unsigned32	read-create	Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
U32 dellNetBgpM2CfgPeerHoldTimeConfigured	1.3.6.1.4.1.6027.20.1.2.8.4.1.2	Unsigned32	read-create	Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (dellNetBgpM2PeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.
U32 dellNetBgpM2CfgPeerKeepAliveConfigured	1.3.6.1.4.1.6027.20.1.2.8.4.1.3	Unsigned32	read-create	Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages frequency relative to the value specified in dellNetBgpM2PeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by dellNetBgpM2PeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of dellNetBgpM2PeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
U32 dellNetBgpM2CfgPeerMinASOrigInterval	1.3.6.1.4.1.6027.20.1.2.8.4.1.4	Unsigned32	read-create	Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds.
U32 dellNetBgpM2CfgPeerMinRouteAdverInter	1.3.6.1.4.1.6027.20.1.2.8.4.1.5	Unsigned32	read-create	Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.
dellNetBgpM2CfgPeerExtensions	1.3.6.1.4.1.6027.20.1.2.8.5
dellNetBgpM2CfgPeerNonCapExts	1.3.6.1.4.1.6027.20.1.2.8.5.1
dellNetBgpM2CfgPeerRouteReflectionExts	1.3.6.1.4.1.6027.20.1.2.8.5.1.2796
dellNetBgpM2CfgPeerReflectorClientTable	1.3.6.1.4.1.6027.20.1.2.8.5.1.2796.1		not-accessible	Table of route reflection client settings on a per-peer basis.
dellNetBgpM2CfgPeerReflectorClientEntry	1.3.6.1.4.1.6027.20.1.2.8.5.1.2796.1.1		not-accessible	Entry containing data on a per-peer basis on whether the peer is configured as a route reflector client.
INT dellNetBgpM2CfgPeerReflectorClient	1.3.6.1.4.1.6027.20.1.2.8.5.1.2796.1.1.1	INTEGER	read-create	This value indicates whether the given peer is a reflector client of this router, or not. A value of nonClient indicates that this peer is not a reflector client. A value of client indicates that this peer is a reflector client that is not fully meshed with other reflector clients. A value of meshedClient indicates that the peer is a reflector client and is fully meshed with all other reflector clients. This value must be nonClient (0) for BGP external peers.
dellNetBgpM2CfgPeerASConfederationExts	1.3.6.1.4.1.6027.20.1.2.8.5.1.3065
dellNetBgpM2CfgPeerConfedMemberTable	1.3.6.1.4.1.6027.20.1.2.8.5.1.3065.1		not-accessible	Table of confederation member settings on a per-peer basis.
dellNetBgpM2CfgPeerConfedMemberEntry	1.3.6.1.4.1.6027.20.1.2.8.5.1.3065.1.1		not-accessible	Entry containing data on a per-peer basis on whether the peer is configured as a BGP confederation member.
T/F dellNetBgpM2CfgPeerConfedMember	1.3.6.1.4.1.6027.20.1.2.8.5.1.3065.1.1.1	TruthValue	read-create	This value indicates whether the given peer is in our confederation or not.
dellNetBgpM2CfgPeerCapExts	1.3.6.1.4.1.6027.20.1.2.8.5.2
dellNetBgpM2Rib	1.3.6.1.4.1.6027.20.1.3
dellNetBgpM2NlriTable	1.3.6.1.4.1.6027.20.1.3.1		not-accessible	The BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers. Collectively, this represents the Adj-Ribs-In. The route where dellNetBgpM2NlriBest is TRUE represents, for this NLRI, the route that is installed in the LocRib from the Adj-Ribs-In.
dellNetBgpM2NlriEntry	1.3.6.1.4.1.6027.20.1.3.1.1		not-accessible	Information about a path to a network.
U32 dellNetBgpM2NlriIndex	1.3.6.1.4.1.6027.20.1.3.1.1.1	Unsigned32	read-only	This index allows for multiple instances of a base prefix for a certain AFI SAFI from a given peer. This is currently useful for two things: 1. Allowing for a peer in future implementations to send more than a single route instance. 2. Allow for extensions which extend the NLRI field to send the same prefix while utilizing other extension specific information. An example of this is RFC 3107 - Carrying MPLS labels in BGP.
DEL dellNetBgpM2NlriAfi	1.3.6.1.4.1.6027.20.1.3.1.1.2	DellNetBgpM2Afi	read-only	The address family of the prefix for this NLRI.
DEL dellNetBgpM2NlriSafi	1.3.6.1.4.1.6027.20.1.3.1.1.3	DellNetBgpM2Safi	read-only	The subsequent address family of the prefix for this NLRI
IPt dellNetBgpM2NlriPrefixType	1.3.6.1.4.1.6027.20.1.3.1.1.4	InetAddressType	read-only	The type of the IP address prefix in the Network Layer Reachability Information field. The value of this object is derived from the appropriate value from the dellNetBgpM2NlriAfi field. Where an appropriate InetAddressType is not available, the value of the object must be unknown(0). XXX TODO - This seems like a hack.
IP dellNetBgpM2NlriPrefix	1.3.6.1.4.1.6027.20.1.3.1.1.5	InetAddress	read-only	An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by dellNetBgpM2PathAttrAddrPrefixLen. Any bits beyond the length specified by dellNetBgpM2PathAttrAddrPrefixLen are zeroed.
ADR dellNetBgpM2NlriPrefixLen	1.3.6.1.4.1.6027.20.1.3.1.1.6	InetAddressPrefixLength	read-only	Length in bits of the address prefix in the Network Layer Reachability Information field.
T/F dellNetBgpM2NlriBest	1.3.6.1.4.1.6027.20.1.3.1.1.7	TruthValue	read-only	An indication of whether or not this route was chosen as the best BGP4 route.
U32 dellNetBgpM2NlriCalcLocalPref	1.3.6.1.4.1.6027.20.1.3.1.1.8	Unsigned32	read-only	The degree of preference calculated by the receiving BGP4 speaker for an advertised route.
U32 dellNetBgpM2PathAttrIndex	1.3.6.1.4.1.6027.20.1.3.1.1.9	Unsigned32	read-only	This value is a unique index for the per-NLRI entry in the dellNetBgpM2PathAttrTable. It is assigned by the agent at the point of creation of the dellNetBgpM2PathAttrTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of dellNetBgpM2PathAttrIndex row instance values across rows of the dellNetBgpM2PeerAttrTable. It is used to provide an index structure for other tables whose data is logically per-peer, per-NLRI.
INT dellNetBgpM2NlriOpaqueType	1.3.6.1.4.1.6027.20.1.3.1.1.10	INTEGER	read-only	This object enumerates the type of the row that is pointed to in the table row dellNetBgpM2NlriOpaquePointer instance, if dellNetBgpM2NlriOpaquePointer is in fact not a zero length. dellNetBgpM2NlriOpaqueType is necessary since the data referenced by dellNetBgpM2NlriOpaquePointer is opaque to BGP. For example, in the case of RFC 3107, the label stack that is pointed to may occur in the mplsLabelStackTable from the MPLS-LSR-MIB, and the instance value of dellNetBgpM2NlriOpaqueType would be bgpMplsLabelStack(1).
NUM dellNetBgpM2NlriOpaquePointer	1.3.6.1.4.1.6027.20.1.3.1.1.11	RowPointer	read-only	Pointer to a row that decomposes the data that is opaque to the BGP MIB but is sent in the NLRI. This RowPointer has zero (0) length data instance if dellNetBgpM2NlriOpaqueType is none.
dellNetBgpM2AdjRibsOutTable	1.3.6.1.4.1.6027.20.1.3.2		not-accessible	This table contains on a per-peer basis one or more routes from the dellNetBgpM2NlriTable that have been placed in this peer's Adj-Ribs-Out.
dellNetBgpM2AdjRibsOutEntry	1.3.6.1.4.1.6027.20.1.3.2.1		not-accessible	List of BGP routes that have been placed into a peer's Adj-Ribs-Out.
U32 dellNetBgpM2AdjRibsOutIndex	1.3.6.1.4.1.6027.20.1.3.2.1.1	Unsigned32	read-only	Certain extensions to BGP permit multiple instance of a per afi, per safi prefix to be advertised to a peer. This object allows the enumeration of them.
NUM dellNetBgpM2AdjRibsOutRoute	1.3.6.1.4.1.6027.20.1.3.2.1.2	RowPointer	read-only	This object points to the route in the dellNetBgpM2NlriTable that corresponds to the entry in the peer's Adj-Rib-Out. Outgoing route maps are not reflected at this point as those are part of the Update-Send process.
C32 dellNetBgpM2PathAttrCountEx	1.3.6.1.4.1.6027.20.1.3.3	Counter32	read-only	The number of entries in the dellNetBgpM2PathAttrTable.
dellNetBgpM2PathAttrTable	1.3.6.1.4.1.6027.20.1.3.4		not-accessible	Provides per advertised network-prefix attribute data, as advertised over a peering session.
dellNetBgpM2PathAttrEntry	1.3.6.1.4.1.6027.20.1.3.4.1		not-accessible	Each entry contains data about a given network prefix, per-prefix and per-advertising peer.
INT dellNetBgpM2PathAttrOrigin	1.3.6.1.4.1.6027.20.1.3.4.1.1	INTEGER	read-only	The ultimate origin of the path information.
IPt dellNetBgpM2PathAttrNextHopAddrType	1.3.6.1.4.1.6027.20.1.3.4.1.2	InetAddressType	read-only	The address family of the address for the border router that should be used to access the destination network.
IP dellNetBgpM2PathAttrNextHop	1.3.6.1.4.1.6027.20.1.3.4.1.3	InetAddress	read-only	The address of the border router that should be used to access the destination network. This address is the nexthop address received in the UPDATE packet. The address family of this object will be the same as that of the prefix in this row. Note that for RFC2545 style double nexthops, this object will always contain the global scope nexthop. dellNetBgpM2LinkLocalNextHopTable will contain the linklocal scope nexthop. In the case that the mechanism documented in draft-kato-bgp-ipv6-link-local-00.txt is used and only a link local nexthop has been sent, , dellNetBgpM2LinkLocalNextHopPresent will be false and dellNetBgpM2PathAttrNextHop will contain the link local nexthop.
T/F dellNetBgpM2PathAttrMedPresent	1.3.6.1.4.1.6027.20.1.3.4.1.4	TruthValue	read-only	Whether or not the MED value is present. If it is not present, the dellNetBgpM2PathAttrMed object has no useful value and should be set to 0.
U32 dellNetBgpM2PathAttrMed	1.3.6.1.4.1.6027.20.1.3.4.1.5	Unsigned32	read-only	This metric is used to discriminate between multiple exit points to an adjacent autonomous system.
T/F dellNetBgpM2PathAttrLocalPrefPresent	1.3.6.1.4.1.6027.20.1.3.4.1.6	TruthValue	read-only	Whether or not the LocalPref value is present. If it is not present, the dellNetBgpM2PathAttrLocalPref object has no useful value and should be set to 0.
U32 dellNetBgpM2PathAttrLocalPref	1.3.6.1.4.1.6027.20.1.3.4.1.7	Unsigned32	read-only	The originating BGP4 speakers degree of preference for an advertised route.
INT dellNetBgpM2PathAttrAtomicAggregate	1.3.6.1.4.1.6027.20.1.3.4.1.8	INTEGER	read-only	When this object is set to atomicAggregatePresent, the ATOMIC_AGGREGATE Path Attribute is present and indicates that the NLRI MUST NOT be made more specific.
INE dellNetBgpM2PathAttrAggregatorAS	1.3.6.1.4.1.6027.20.1.3.4.1.9	InetAutonomousSystemNumber	read-only	The AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute. Note propagation of AS of zero is illegal in the Internet.
OID dellNetBgpM2PathAttrAggregatorAddr	1.3.6.1.4.1.6027.20.1.3.4.1.10	DellNetBgpM2Identifier	read-only	The IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
U32 dellNetBgpM2AsPathCalcLength	1.3.6.1.4.1.6027.20.1.3.4.1.11	Unsigned32	read-only	This value represents the calculated length of the AS Path according to the rules of the BGP specification. This value is used in route selection.
STR dellNetBgpM2AsPathString	1.3.6.1.4.1.6027.20.1.3.4.1.12	SnmpAdminString	read-only	This is a string depicting the autonomous system path to this network which was received from the peer which advertised it. The format of the string is implementation-dependent, and should be designed for operator readability.
U32 dellNetBgpM2AsPathIndex	1.3.6.1.4.1.6027.20.1.3.4.1.13	Unsigned32	read-only	This value is a unique index for the decomposed AS Path in the dellNetBgpM2AsPathTable. It is assigned by the agent at the point of creation of the dellNetBgpM2AsPathTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of dellNetBgpM2AsPathIndex row instance values across rows of the dellNetBgpM2AsPathTable.
dellNetBgpM2AsPath4byteTable	1.3.6.1.4.1.6027.20.1.3.5		not-accessible	This table is present for BGP speakers that support the AS 4byte specification and are functioning as a router between 2-byte and 4-byte AS space.
dellNetBgpM2AsPath4byteEntry	1.3.6.1.4.1.6027.20.1.3.5.1		not-accessible	Each row contains the information for the AS 4-byte extension's NEW_AS_PATH and NEW_AGGREGATOR attributes.
T/F dellNetBgpM2AsPath4bytePathPresent	1.3.6.1.4.1.6027.20.1.3.5.1.1	TruthValue	read-only	This value may only be true if this BGP Speaker is functioning as a router between ASs that are in 2-byte and 4-byte AS space. If this value is true, then the NEW_AS_PATH attributes are present and the 4-byte versions of the appropriate path attributes are in this row. If this value is false, then the following values will be present in the row: dellNetBgpM2PathAttrAggregatorAS - zero (0). dellNetBgpM2AsPathCalcLength - zero (0). dellNetBgpM2AsPathString - zero (0) length string. dellNetBgpM2AsPathIndex - zero (0).
INE dellNetBgpM2AsPath4byteAggregatorAS	1.3.6.1.4.1.6027.20.1.3.5.1.2	InetAutonomousSystemNumber	read-only	The NEW_AGGREGATOR AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute. Note propagation of AS of zero is illegal in the Internet.
U32 dellNetBgpM2AsPath4byteCalcLength	1.3.6.1.4.1.6027.20.1.3.5.1.3	Unsigned32	read-only	This value represents the calculated length of the NEW_AS_PATH according to the rules of the BGP specification. This value is used in route selection.
STR dellNetBgpM2AsPath4byteString	1.3.6.1.4.1.6027.20.1.3.5.1.4	SnmpAdminString	read-only	This is a string depicting the autonomous system path to this network which was received from the peer which advertised it. The format of the string is implementation-dependent, and should be designed for operator readability.
U32 dellNetBgpM2AsPath4byteIndex	1.3.6.1.4.1.6027.20.1.3.5.1.5	Unsigned32	read-only	This value is a unique index for the decomposed AS Path in the dellNetBgpM2AsPathTable. It is assigned by the agent at the point of creation of the dellNetBgpM2AsPathTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of dellNetBgpM2AsPathIndex row instance values across rows of the dellNetBgpM2AsPathTable.
dellNetBgpM2AsPathTable	1.3.6.1.4.1.6027.20.1.3.6		not-accessible	The BGP-4 Path Attribute AS Path Table contains the per network path (NLRI) AS PATH data received from the advertising BGP peer.
dellNetBgpM2AsPathTableEntry	1.3.6.1.4.1.6027.20.1.3.6.1		not-accessible	Information about an AS path provided with a path to a network.
U32 dellNetBgpM2AsPathSegmentIndex	1.3.6.1.4.1.6027.20.1.3.6.1.1	Unsigned32	read-only	A per-AS path segment index. This will index a set of autonomous systems in an AS path which are part of the same sequence or set (as determined by the row value of dellNetBgpM2AsPathType, which should be the same value for each dellNetBgpM2AsPathTable entry indexed by the same (dellNetBgpM2PathAttrIndex, dellNetBgpM2AsPathIndex) pair).
U32 dellNetBgpM2AsPathElementIndex	1.3.6.1.4.1.6027.20.1.3.6.1.2	Unsigned32	read-only	A per-AS element index. This will index a particular AS within a sequence or set of autonomous systems in an AS path.
INT dellNetBgpM2AsPathType	1.3.6.1.4.1.6027.20.1.3.6.1.3	INTEGER	read-only	The type of sequence in which this asPath was advertised as an attribute. Note that all asPath row instances for a given (dellNetBgpM2PathAttrIndex, dellNetBgpM2AsPathIndex) index pair will have their dellNetBgpM2AsPathType set to the same value. The values for dellNetBgpM2AsPathType are interpreted as defined in the base BGP document and the BGP AS Confederations document.
INE dellNetBgpM2AsPathElementValue	1.3.6.1.4.1.6027.20.1.3.6.1.4	InetAutonomousSystemNumber	read-only	An AS value for an AS the related NLRI traversed in the propagation of its advertisement. This value is to be interpreted in the context of the sequence implied by dellNetBgpM2AsPathIndex and dellNetBgpM2AsPathType (and, in sequence of the other table rows with the same value of dellNetBgpM2PathAttrIndex and dellNetBgpM2AsPathIndex).
dellNetBgpM2PathAttrUnknownTable	1.3.6.1.4.1.6027.20.1.3.7		not-accessible	The BGP-4 Path Attribute Unknown Table contains the per network path (NLRI) data on the path attributes advertised with a route but not known to the local BGP implementation or not otherwise capable of being returned from this agent. The absence of row data for a given index value for dellNetBgpM2PathAttrIndex indicates a lack of such unknown attribute information for the indicated network path (as indexed by that dellNetBgpM2PathAttrIndex value in the dellNetBgpM2PathAttrTable).
dellNetBgpM2PathAttrUnknownEntry	1.3.6.1.4.1.6027.20.1.3.7.1		not-accessible	Information about an unknown attribute provided with a path to a network.
U32 dellNetBgpM2PathAttrUnknownIndex	1.3.6.1.4.1.6027.20.1.3.7.1.1	Unsigned32	read-only	An integer index for a row in this table.
U32 dellNetBgpM2PathAttrUnknownType	1.3.6.1.4.1.6027.20.1.3.7.1.2	Unsigned32	read-only	The attribute type advertised with this unknown attribute by the peer.
OCT dellNetBgpM2PathAttrUnknownValue	1.3.6.1.4.1.6027.20.1.3.7.1.3	OCTET STRING	read-only	Value of path attribute not understood by the base BGP-4 document. Octets beyond the maximum size, if any, are not recorded by this row object.
dellNetBgpM2PathAttrExtensions	1.3.6.1.4.1.6027.20.1.3.8
dellNetBgpM2PathAttrNonCapExts	1.3.6.1.4.1.6027.20.1.3.8.1
dellNetBgpM2PathAttrCommunityExts	1.3.6.1.4.1.6027.20.1.3.8.1.1997
dellNetBgpM2PathAttrCommTable	1.3.6.1.4.1.6027.20.1.3.8.1.1997.1		not-accessible	The BGP-4 Path Attribute Community Table contains the per network path (NLRI) data on the community membership advertised with a route. The absence of row data for a given index value for dellNetBgpM2PathAttrIndex indicates a lack of this attribute information for the indicated network path (as indexed by that dellNetBgpM2PathAttrIndex value in the dellNetBgpM2PathAttrTable).
dellNetBgpM2PathAttrCommEntry	1.3.6.1.4.1.6027.20.1.3.8.1.1997.1.1		not-accessible	Information about a community association provided with a path to a network.
U32 dellNetBgpM2PathAttrCommIndex	1.3.6.1.4.1.6027.20.1.3.8.1.1997.1.1.1	Unsigned32	read-only	An integer index for a row in this table.
DEL dellNetBgpM2PathAttrCommValue	1.3.6.1.4.1.6027.20.1.3.8.1.1997.1.1.2	DellNetBgpM2Community	read-only	A value representing a community. There are certain 4-octet long values which could be returned in this columnar row data that carry additional semantics.
dellNetBgpM2LinkLocalNextHopTable	1.3.6.1.4.1.6027.20.1.3.8.1.2545		not-accessible	Table of link local nexthops as sent by RFC 2545 for IPv6 BGP Speakers.
dellNetBgpM2LinkLocalNextHopEntry	1.3.6.1.4.1.6027.20.1.3.8.1.2545.1		not-accessible	Entry containing the link-local nexthops as sent by a BGP speaker running RFC 2545 extensions for double-nexthops.
T/F dellNetBgpM2LinkLocalNextHopPresent	1.3.6.1.4.1.6027.20.1.3.8.1.2545.1.1	TruthValue	read-only	This value is TRUE if and only if the BGP speaker is receiving IPv6 NLRI using the RFC 2545 double nexthop convention and it has received a link local scope nexthop in addition to the global scope nexthop.
IP dellNetBgpM2LinkLocalNextHop	1.3.6.1.4.1.6027.20.1.3.8.1.2545.1.2	InetAddress	read-only	This value contains an IPv6 link local address of InetAddressType of type ipv6z. This value is only present if dellNetBgpM2LinkLocalNextHopPresent is true.
dellNetBgpM2PathAttrRouteReflectionExts	1.3.6.1.4.1.6027.20.1.3.8.1.2796
dellNetBgpM2PathAttrOriginatorIdTable	1.3.6.1.4.1.6027.20.1.3.8.1.2796.1		not-accessible	Per prefix data pertinent to advertisement of a network prefix through an originator.
dellNetBgpM2PathAttrOriginatorIdEntry	1.3.6.1.4.1.6027.20.1.3.8.1.2796.1.1		not-accessible	Each entry contains data pertinent to a network prefix as received through its originating BGP route reflector.
OID dellNetBgpM2PathAttrOriginatorId	1.3.6.1.4.1.6027.20.1.3.8.1.2796.1.1.1	DellNetBgpM2Identifier	read-only	The Originator-ID identifying the router that initially advertised this destination to a Route Reflector. A value of 0.0.0.0 indicates the absence of this attribute.
dellNetBgpM2PathAttrClusterTable	1.3.6.1.4.1.6027.20.1.3.8.1.2796.2		not-accessible	The BGP-4 Path Attribute Cluster Table contains the per network path (NLRI) data on the reflection path which a route has traversed. The absence of row data for a given index value for dellNetBgpM2PathAttrIndex indicates a lack of this attribute information for the indicated network path (as indexed by that dellNetBgpM2PathAttrIndex value in the dellNetBgpM2PathAttrTable).
dellNetBgpM2PathAttrClusterEntry	1.3.6.1.4.1.6027.20.1.3.8.1.2796.2.1		not-accessible	Information about a cluster traversal provided with a path to a network.
U32 dellNetBgpM2PathAttrClusterIndex	1.3.6.1.4.1.6027.20.1.3.8.1.2796.2.1.1	Unsigned32	read-only	An integral index for a row in this table.
OID dellNetBgpM2PathAttrClusterValue	1.3.6.1.4.1.6027.20.1.3.8.1.2796.2.1.2	DellNetBgpM2Identifier	read-only	A four octet long value representing a part of the reflection path that the route has passed. Each such four octet long value represents the ID of a cluster that the route has traversed. The sequence of this path as received in the route advertisement will be preserved in the sequence of dellNetBgpM2PathAttrClusterTable rows (and the dellNetBgpM2PathAttrClusterValues in each row) as returned for a given dellNetBgpM2PathAttrIndex value, and the monotonically increasing sequence of dellNetBgpM2PathAttrClusterIndex values for that dellNetBgpM2PathAttrIndex.
dellNetBgpM2PathAttrExtCommTable	1.3.6.1.4.1.6027.20.1.3.8.1.3501		not-accessible	The BGP-4 Path Attribute Community Table contains the per network path (NLRI) data on the extended community membership advertised with a route. The absence of row data for a given index value for dellNetBgpM2PathAttrIndex indicates a lack of this attribute information for the indicated network path (as indexed by that dellNetBgpM2PathAttrIndex value in the dellNetBgpM2PathAttrTable). XXX JMH - can not assign the OID until an RFC is published.
dellNetBgpM2PathAttrExtCommEntry	1.3.6.1.4.1.6027.20.1.3.8.1.3501.1		not-accessible	Information about an extended community association provided with a path to a network.
U32 dellNetBgpM2PathAttrExtCommIndex	1.3.6.1.4.1.6027.20.1.3.8.1.3501.1.1	Unsigned32	read-only	An integral index for a row in this table.
DEL dellNetBgpM2PathAttrExtCommValue	1.3.6.1.4.1.6027.20.1.3.8.1.3501.1.2	DellNetBgpM2ExtendedCommunity	read-only	A value representing an extended community which was received with the route implied by the dellNetBgpM2PathAttr Index value of this row data. There are certain 8-octet long values which could be returned in this columnar row data that carry additional semantics.
dellNetBgpM2PathAttrCapExts	1.3.6.1.4.1.6027.20.1.3.8.2
dellNetBgpM2Conformance	1.3.6.1.4.1.6027.20.1.4
dellNetBgpM2MIBCompliances	1.3.6.1.4.1.6027.20.1.4.1
dellNetBgpM2MIBCompliance	1.3.6.1.4.1.6027.20.1.4.1.1			The compliance statement for entities which implement the BGP4 mib.
dellNetBgpM2MIBGroups	1.3.6.1.4.1.6027.20.1.4.2
dellNetBgpM2CommunitiesGroup	1.3.6.1.4.1.6027.20.1.4.2.1			Objects associated with BGP communities.
dellNetBgpM2ExtCommunitiesGroup	1.3.6.1.4.1.6027.20.1.4.2.2			Objects associated with BGP extended communities.
dellNetBgpM2RouteReflectionGroup	1.3.6.1.4.1.6027.20.1.4.2.3			Objects associated with BGP route reflection.
dellNetBgpM2AsConfederationGroup	1.3.6.1.4.1.6027.20.1.4.2.4			Objects associated with BGP confederation membership.
dellNetBgpM2TimersGroup	1.3.6.1.4.1.6027.20.1.4.2.5			Objects associated with BGP peering timers.
dellNetBgpM2CountersGroup	1.3.6.1.4.1.6027.20.1.4.2.6			Objects to count discrete events and exchanges on BGP sessions.
dellNetBgpM2CapabilitiesGroup	1.3.6.1.4.1.6027.20.1.4.2.7			Objects to report capabilities as received on BGP sessions.
dellNetBgpM2AsPathGroup	1.3.6.1.4.1.6027.20.1.4.2.8			Objects to report AS paths received on BGP NLRIs.
dellNetBgpM2As4byteGroup	1.3.6.1.4.1.6027.20.1.4.2.9			AS Size objects.
dellNetBgpM2BaseGroup	1.3.6.1.4.1.6027.20.1.4.2.10			Basic objects in local BGP implementation.
dellNetBgpM2ErrorsGroup	1.3.6.1.4.1.6027.20.1.4.2.11			Errors received on BGP peering sessions.
dellNetBgpM2PeerGroup	1.3.6.1.4.1.6027.20.1.4.2.12			Core object types on BGP peering sessions.
dellNetBgpM2PathAttributesGroup	1.3.6.1.4.1.6027.20.1.4.2.13			Attributes received on BGP peering sessions.
dellNetBgpM2PeerConfigurationGroup	1.3.6.1.4.1.6027.20.1.4.2.14			Configuration objects for BGP peers.
dellNetBgpM2PeerRouteReflectorCfgGroup	1.3.6.1.4.1.6027.20.1.4.2.15			Configuration objects for BGP peers that support route reflection.
dellNetBgpM2PeerAsConfederationCfgGroup	1.3.6.1.4.1.6027.20.1.4.2.16			Configuration objects for BGP peers that support BGP confederations.
dellNetBgpM2MIBNotificationsGroup	1.3.6.1.4.1.6027.20.1.4.2.17			This group contains objects for notifications supported by this mib module.
dellNetBgpM2Rfc2545Group	1.3.6.1.4.1.6027.20.1.4.2.18			This group is required for peers that support exchanging of IPv6 NLRI per RFC 2545.

RFC description

Manages BGP4 version 2 peer sessions and routing policy for Dell Networking switches.

Start monitoring Dell Networking switch/router (BGP4) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DELL-NETWORKING-BGP4-V2-MIB