| OID symbolic | OID numeric | Type | Access | Description |
|---|
| INT lapbcnvSysRouteConnectInterval | 1.3.6.1.4.1.495.2.1.6.28.1 | INTEGER | read-write | Determines the number of seconds between attempts to establish a
connection for a LAPB system route. A connection is attempted only for
defined non-connected routes.
Range of Values: 10 - 900 seconds
Default Value: 30 seconds
Configuration Changed: administrative and operative |
| lapbcnvSapTable | 1.3.6.1.4.1.495.2.1.6.28.10 | | not-accessible | A table containing configuration information about each LAPB convergence
service access point. Service access points of this type exist at the
upper interface of the LAPB Convergence layer, and are used to communicate
with the LAPBD or IAM layers. |
| lapbcnvSapEntry | 1.3.6.1.4.1.495.2.1.6.28.10.1 | | not-accessible | Defines a row in the Service Access Point Configuration table. Each row
contains the objects which are used to define a service access point upper
interface of the LAPB Convergence layer. |
| PSA lapbcnvSapNumber | 1.3.6.1.4.1.495.2.1.6.28.10.1.1 | PSapIndex | read-only | Identifies this SAP (service access point) with a numerical value. Values
are unique for each service access point. |
| INT lapbcnvSapRowStatus | 1.3.6.1.4.1.495.2.1.6.28.10.1.2 | INTEGER | read-write | Determines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table immediately, however values are
still in effect until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: valid (2)
Configuration Changed: administrative |
| ALI lapbcnvSapAlias | 1.3.6.1.4.1.495.2.1.6.28.10.1.3 | Alias | read-write | Identifies this service access point by a textual name. Names must be
unique across all service access points at all layers.
Range of Values: 1 -16 alphanumeric characters (first character must be a
letter)
Default Value: none
Configuration Changed: administrative |
| INT lapbcnvSapControl | 1.3.6.1.4.1.495.2.1.6.28.10.1.5 | INTEGER | write-only | Permits control of a specific SAP (service access point).
Options:
clearStats (1): Clear all statistics stored by statistics objects.
Configuration Changed: operative |
| INT lapbcnvSapState | 1.3.6.1.4.1.495.2.1.6.28.10.1.6 | INTEGER | read-only | Indicates the current state of this SAP (service access point).
Options:
offLine (1): Indicates a newly created service access point whose
configuration has not yet been sent to the LAPB Convergence layer.
unbound (2): SAP is not yet bound to its companion SAP at an upper layer.
notConnected (3): The associated route with this SAP is not connected, or
there is no route associated with this SAP.
inProgress (4): The associated route is in the process of connecting.
connected (5): The associated route is connected. |
| CTR lapbcnvSapTxFrames | 1.3.6.1.4.1.495.2.1.6.28.10.1.7 | Counter | read-only | Indicates the number of frames transmitted by this service access point. |
| CTR lapbcnvSapRxFrames | 1.3.6.1.4.1.495.2.1.6.28.10.1.8 | Counter | read-only | Indicates the number of frames received by this service access point. |
| CTR lapbcnvSapTxOctets | 1.3.6.1.4.1.495.2.1.6.28.10.1.9 | Counter | read-only | Indicates the number of octets transmitted by this service access point. |
| CTR lapbcnvSapRxOctets | 1.3.6.1.4.1.495.2.1.6.28.10.1.10 | Counter | read-only | Indicates the number of octets received by this service access point. |
| CTR lapbcnvSapOutSuccessfullConnects | 1.3.6.1.4.1.495.2.1.6.28.10.1.11 | Counter | read-only | Indicates the number of successful outgoing connections established by
this SAP (service access point). An outgoing connection is always
attempted from LAPB convergence to the Inter-Application Module (IAM).
At the PSAP, this object represents the total number of outgoing
connections established by all SAPs. At each individual SAP, this object
represents the number of outgoing connections established by only that
SAP. |
| CTR lapbcnvSapOutUnsuccessfullConnects | 1.3.6.1.4.1.495.2.1.6.28.10.1.12 | Counter | read-only | Indicates the number of unsuccessful outgoing connections attempted by
this SAP (service access point). An outgoing connection is always
attempted from LAPB convergence to the Inter-Application Module (IAM).
At the PSAP, this object represents the total number of unsuccessful
outgoing connections attempted by all SAPs. At each individual SAP, this
object represents the number of unsuccessful outgoing connections
attempted by only that SAP. |
| CTR lapbcnvSapInSuccessfullConnects | 1.3.6.1.4.1.495.2.1.6.28.10.1.13 | Counter | read-only | Indicates the number of successful incoming connections established at
this SAP (service access point). An incoming connection is always
attempted from the Inter-Application Module (IAM) to LAPB convergence.
At the PSAP, this object represents the total number of successful
incoming connections for all SAPs. At each individual SAP, this object
represents the number of successful incoming connections for only that
SAP. |
| CTR lapbcnvSapInUnsuccessfullConnects | 1.3.6.1.4.1.495.2.1.6.28.10.1.14 | Counter | read-only | Indicates the number of unsuccessful incoming connections attempted at
this SAP (service access point). An incoming connection is always
attempted from the Inter-Application Module (IAM) to LAPB convergence.
At the PSAP, this object represents the total number of unsuccessful
incoming connections for all SAPs. At each individual SAP, this object
represents the number of unsuccessful incoming connections for only that
SAP. |
| CTR lapbcnvSapUnopenedServiceDiscards | 1.3.6.1.4.1.495.2.1.6.28.10.1.15 | Counter | read-only | This object applies only to the PSAP (public service access point).
Indicates the number of frames received and discarded by the PSAP because:
- no route was associated with the frame
- the frame was destined for a route that is not connected |
| CTR lapbcnvSapTxResets | 1.3.6.1.4.1.495.2.1.6.28.10.1.16 | Counter | read-only | This object applies only to the PSAP (public service access point).
Indicates the number of Inter- Application Module (IAM) reset frames sent
by the PSAP. |
| CTR lapbcnvSapRxResets | 1.3.6.1.4.1.495.2.1.6.28.10.1.17 | Counter | read-only | This object applies only to the PSAP.
Indicates the number of Inter- Application Module (IAM) reset frames
received by the PSAP. |
| lapbcnvSysRouteTable | 1.3.6.1.4.1.495.2.1.6.28.11 | | not-accessible | A table containing information about each LAPB system route. Routes allow
this LAPB/D layer to link with another LAPB/D layer across a frame relay
network, or with the LAPB layer on another similar card in the same
chassis (for future use with the CX1000). |
| lapbcnvSysRouteEntry | 1.3.6.1.4.1.495.2.1.6.28.11.1 | | not-accessible | Defines a row in the lapbcnvSysRouteTable. Each row contains the objects
which define a system route. |
| SAP lapbcnvSRSapNumber | 1.3.6.1.4.1.495.2.1.6.28.11.1.1 | SapIndex | read-only | Identifies the service access point this route entry is associated with. |
| INT lapbcnvSRRowStatus | 1.3.6.1.4.1.495.2.1.6.28.11.1.2 | INTEGER | read-write | Determines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table immediately, however values are
still in effect until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: none
Configuration Changed: administrative and operative |
| ALI lapbcnvSRDestAlias | 1.3.6.1.4.1.495.2.1.6.28.11.1.3 | Alias | read-write | Determines the textual name of the destination service this route
connects to. When attempting a LAPB connection across Frame Relay, this
object specifies the name of the outgoing circuit at the Frame Relay
layer.
When attempting a LAPB connection between cards within the same chassis
(future use within CX1000), this object specifies the name of the LAPB
Convergence SAP on the remote card.
Range of Values: 1 -16 characters (first character must be a letter)
Default Value: none
Configuration Changed: administrative and operative |
| SUB lapbcnvSRSubRef | 1.3.6.1.4.1.495.2.1.6.28.11.1.4 | SubRef | read-write | Specifies a reference number that uniquely identifies this route. This
number is used by the FRIM (Frame Relay Interface Module) to identify
routes using the same DLCI (enables PVC consolidation). This number must
be unique for all routes sharing the same DLCI.
Range of Values: 1 - 255 (when using PVC consolidation)
0 (when not using PVC consolidation)
Default Value: 0
Configuration Changed: administrative and operative |
| INT lapbcnvSRRouteStatus | 1.3.6.1.4.1.495.2.1.6.28.11.1.10 | INTEGER | read-only | Indicates the connection status of this LAPB route.
Options:
offLine (1): Indicates that the LAPB Convergence SAP this route is
associated with does not exist or is offline.
notConnected (2): Indicates that the remote destination does not exist, or
has refused the connection.
inProgress (3): Indicates that the connection is in the process of being
established. This is a transient state.
connected (4): Indicates that the connection is established and is ready
for data transfer. |
| INT lapbcnvSRClearStatus | 1.3.6.1.4.1.495.2.1.6.28.11.1.11 | INTEGER | read-only | Indicates the status of a failed connection. The value of this object is
only valid only between attempts to establish the route connection
(lapbcnvSRRouteStatus = notConnected), and may or may not change after
successive failed attempts.
Options:
noFailure (1): Once a system route has been successfully connected, this
value is maintained for the duration of the connection.
internalError (2): An internal error has occurred.
localAllocFailure (3): There is insufficient memory available for LAPB
Convergence to establish this connection.
remoteAllocFailure (4): There is insufficient memory available for the
destination protocol layer to establish this connection.
localNoAccess (5): This route is associated with a SAP that does not
exist.
remoteNoAccess (6): This route is associated with a SAP that does not
exist at the destination layer.
localPvcDown (7): For future use.
remotePvcDown (8): The PVC at the destination protocol layer is down.
localPvcBusy (9): The SAP associated with this route is already connected.
remotePvcBusy (10): The destination associated with this route is already
connected. This typically occurs when the route is a non-MPE (PVC
consolidating) circuit.
localFcnFailure (11): Flow control negotiation failed.
remoteFcnFailure (12): Flow control negotiation failed at the destination
protocol layer.
localDsnFailure (13): Data size negotiation failed.
localRefInUse (14): Data size negotiation failed at the destination
protocol layer.
remoteAliasNotFound (15): The destination alias (lapbcnvSRDestAlias) does
not exist.
remoteNoPvcService (16): The destination protocol layer does not support
PVC service.
mpeInvalidSubref (17): The value of lapbcnvSRSubRef is invalid at the
destination protocol layer. (i.e., lapcnvSRSubRef is set to '0' and the
destination frame relay circuit is configured for PVC consolidation). |
