All MIBs › CTRON-REMOTE-ACCESS-MIB
Category: VPN and Security, Vendor: Cabletron/Enterasys
Description: Manages Cabletron remote access server configuration, dial-in user sessions, and PPP/ISDN parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CTRON-REMOTE-ACCESS-MIB?
CTRON-REMOTE-ACCESS-MIB is a Cabletron (later Enterasys) enterprise MIB for managing a Cabletron remote-access server appliance, covering dial-in user session and PPP/ISDN connection parameters. It exposes configuration data for remote-access ports/lines along with session-level state, such as which dial-in users are currently connected and their PPP/ISDN link parameters. Its main monitoring value is tracking active dial-in sessions and line/connection status - letting an admin see how many remote users are connected, detect failed or dropped PPP negotiations, and confirm ISDN channel/line health, which is effectively software/service-status monitoring of the remote-access function. It likely depends on standard PPP-related MIBs (e.g. the RFC 1471/1472 PPP MIBs) for underlying link-layer parameters even though it is packaged as a Cabletron-specific wrapper. It was deployed on Cabletron/Enterasys remote-access server appliances providing dial-up/ISDN remote connectivity into corporate LANs, a now-legacy access technology. Network engineers evaluating or troubleshooting this functionality can download the CTRON-REMOTE-ACCESS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CTRON-REMOTE-ACCESS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cabletron/Enterasys remote access server
Monitoring Examples
No sample objects were provided for this module. Based on its stated purpose, it plausibly defines a dial-in session table and a PPP/ISDN line-configuration table, and the realistic use would be polling active session count/state and per-line PPP/ISDN parameters to spot line failures or unusually high concurrent-session counts - but since no concrete object names were given, exact identifiers cannot be cited here.
What Can Be Monitored
- active dial-in session count
- PPP link negotiation status per session
- ISDN line status
- remote user connection state
This MIB depends on
Related MIBs
Imported Objects
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| cabletron | 1.3.6.1.4.1.52 | |||
| mibs | 1.3.6.1.4.1.52.4 | |||
| ctron | 1.3.6.1.4.1.52.4.1 | |||
| ctDataLink | 1.3.6.1.4.1.52.4.1.2 | |||
| ctronWan | 1.3.6.1.4.1.52.4.1.2.7 | |||
| ctRemoteAccess | 1.3.6.1.4.1.52.4.1.2.7.2 | |||
| ctRemoteConnection | 1.3.6.1.4.1.52.4.1.2.7.2.1 | |||
| INT ctRemNumConnections | 1.3.6.1.4.1.52.4.1.2.7.2.1.1 | INTEGER | read-only | This object describes the number of physical remote access connections on the platform. |
| ctRemPhysPortTable | 1.3.6.1.4.1.52.4.1.2.7.2.1.2 | not-accessible | A list of the descriptions of the physical remote access ports of this platform. | |
| ctRemPhysPortEntry | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1 | not-accessible | A physical port entry. It contains objects relating to a given physical remote access port | |
| INT ctRemConnectionIndex | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.1 | INTEGER | read-only | A value indicating the remote connection this entry is located on. |
| INT ctRemPhysPortType | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.2 | INTEGER | read-only | The type of physical port that this entry describes. None indicates that the physical port has no connector. |
| OID ctRemPhysPortSpecificMib | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.3 | OBJECT IDENTIFIER | read-only | This object identifies an instance of the index object in the first group of objects in the MIB specific to the physical port. |
| INT ctRemPhysPortProtMgrType | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.4 | INTEGER | read-write | This object identifies an instance of the type of Protocol Manager residing on this physical port. Before a physical port may be used, the type of manager must be designated. For example, if the physical port was going to be used as an ISDN PRI interface, with dial up PPP links, then the manager type would be set to (4), ISDN-PRI-PPP. |
| INT ctRemPhysPortProtMgrIfaceNum | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.5 | INTEGER | read-write | This object identifies the interface number that will be assigned to the Protocol Managers IFO |
| INT ctRemPhysPortWanIfaceNum | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.6 | INTEGER | read-only | This object identifies the interface number that will be assigned to the Wanio's IFO |
| INT ctRemPhysPortProtMgrMaxIfos | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.7 | INTEGER | read-write | This object identifies the maximum number of IFO's that can be created on this physical interface. |
| STR ctRemPhysPortProtMgrIfaceList | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.8 | DisplayString | read-only | This object identifies a list of interfaces that will be assigned to this Protocol Managers data IFO's |
| INT ctRemPhysAlarmTimeOut | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.9 | INTEGER | read-write | Whenever the physical port is configured for nailed-up PPP this object specifies the time the physical port must remain in a failed state as a condition to begin the backup procedure. The backup procedure is begun for any active interface(s) that were connected over the failed physical port and which have been configured for backup. |
| INT ctRemPhysWpimType | 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.10 | INTEGER | read-write | This Mib object determines the Mode of operation that the T1/DDS Wpim module will function as. Setting a value of 1 will set the mode to DDS, setting a value of 2 will set the mode to T1. |
| ctRemInterfaceTable | 1.3.6.1.4.1.52.4.1.2.7.2.1.3 | not-accessible | The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured. | |
| ctRemInterfaceEntry | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1 | not-accessible | A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products. | |
| INT ctRemIntEntIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.1 | INTEGER | read-only | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| INT ctRemIntEntCompression | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.2 | INTEGER | read-write | This flag will indicate whether compression should take place on this interface. |
| STR ctRemIntEntCompRatio | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.3 | DisplayString | read-only | This string indicates the current compression ratio on this interface. |
| INT ctRemIntEntCompStatus | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.4 | INTEGER | read-only | This flag will indicate whether compression has been nogotiated on this interface. |
| INT ctRemIntEntMTU | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.5 | INTEGER | read-write | The MTU to be negotiated for this interface. This will not be updated with the actual MTU, which can be found in the ifTable. |
| INT ctRemIntEntCongestion | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.6 | INTEGER | read-write | This object identifies the Leaky Bucket algorithm flag for a Frame Relay circuit on this intertface. The option is supported when this flag is enabled, and not supported when this flag is disabled. |
| INT ctRemIntEntMaxProfiles | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.7 | INTEGER | read-write | This object specifies the maximum number of neighbor profiles. A neighbor profile describes a possible connection. The maximum should be set to account for support of PPP multilink. That is to say, if PPP multilink is being used then the number of profiles must at least accomodate the maximum possible number of additional more BW connections. As such, each neighbor profile would then describe a possible connection to the same remote end point. |
| INT ctRemIntEntTxIdleTimeout | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.8 | INTEGER | read-write | This object identifies the idle timeout value in which a packet needs to be transmitted before the interface is automatically disconnected. Allowed values are in increments of five seconds including zero. |
| INT ctRemIntEntRxIdleTimeout | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.9 | INTEGER | read-write | This object identifies the idle timeout in which a packet needs to be received before the interface is automatically disconnected. Allowed values are in increments of five seconds including zero. |
| STR ctRemIntEntCircuitName | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.10 | DisplayString | read-write | This object associates a circuit name with a specific interface. |
| INT ctRemIntEntEncryption | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.11 | INTEGER | read-write | This flag will indicate whether encryption should take place on this interface. |
| INT ctRemIntEntEncryptStatus | 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.12 | INTEGER | read-only | This flag will indicate whether Encryption has been nogotiated on this interface. |
| ctRemPrimaryInterfaceTable | 1.3.6.1.4.1.52.4.1.2.7.2.1.4 | not-accessible | The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured. | |
| ctRemPrimaryInterfaceEntry | 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1 | not-accessible | A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products. | |
| INT ctRemPriIntEntIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1.1 | INTEGER | read-only | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| INT ctRemPriIntEntConnectRetryInterval | 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1.2 | INTEGER | read-write | This object specifies the interval in seconds between retries for restoring the primary interface. |
| ctRemBackupInterfaceTable | 1.3.6.1.4.1.52.4.1.2.7.2.1.5 | not-accessible | The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured. | |
| ctRemBackupInterfaceEntry | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1 | not-accessible | A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products. | |
| INT ctRemIntEntBackupIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.1 | INTEGER | read-only | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| INT ctRemIntEntBackupIfNum | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.2 | INTEGER | read-write | This object identifies which ifIndex will backup this interface in the event of a communications failure. |
| INT ctRemIntEntBackupIfInUseCnt | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.3 | INTEGER | read-only | This object identifies how many other interfaces this interface will backup. |
| INT ctRemIntEntBackupIfTimeToConnect | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.4 | INTEGER | read-write | This object identifies how long to wait in seconds before attempting to switchover to the backup interface. Allowed values are in increments of five seconds including zero. |
| INT ctRemIntEntBackupIfTimeToDisconnect | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.5 | INTEGER | read-write | This object identifies how long to wait in seconds before attempting to switchover to the primary interface. Allowed values are in increments of five seconds including zero. |
| INT ctRemIntEntBackupIfOverride | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.6 | INTEGER | read-write | This object identifies if the interface will switch back to the primary link after it has become active again. A force condition will not allow the interface to switch back. |
| INT ctRemIntEntBackupConnectRetries | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.7 | INTEGER | read-write | This object specifies the number of tries to bring-up the backup interface before giving up. |
| INT ctRemIntEntBackupConnectRetryInterval | 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.8 | INTEGER | read-write | This object specifies the interval in seconds between retries for bringing up backup interface before giving up. |
| ctRemExtPhysPortTable | 1.3.6.1.4.1.52.4.1.2.7.2.1.6 | not-accessible | A list of the descriptions of the physical remote access ports of this platform. | |
| ctRemExtPhysPortEntry | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1 | not-accessible | A physical port entry. It contains objects relating to a given physical remote access port | |
| INT ctRemExtConnectionIndex | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.1 | INTEGER | read-only | A value indicating the remote connection this entry is located on. |
| INT ctRemExtProtMgrIndex | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.2 | INTEGER | read-only | A value indicating the protMgr number for this entry. |
| INT ctRemExtPhysPortProtMgrType | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.3 | INTEGER | read-write | This object identifies an instance of the type of Protocol Manager residing on this physical port. Before a physical port may be used, the type of manager must be designated. For example, if the physical port was going to be used as an ISDN PRI interface, with dial up PPP links, then the manager type would be set to (4), ISDN-PRI-PPP. |
| INT ctRemExtPhysPortProtMgrEnable | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.4 | INTEGER | read-write | This object identifies an instance of the the enable flag of Protocol Manager residing on this physical port. |
| INT ctRemExtPhysPortProtMgrIfaceNum | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.5 | INTEGER | read-write | This object identifies the interface number that will be assigned to the Protocol Managers IFO |
| INT ctRemExtPhysPortProtMgrMaxIfos | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.6 | INTEGER | read-write | This object identifies the maximum number of IFO's that can be created on this physical interface. |
| STR ctRemExtPhysPortProtMgrIfaceList | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.7 | DisplayString | read-only | This object identifies a list of interfaces that will be assigned to this Protocol Managers data IFO's |
| STR ctRemExtPhysPortProtMgrChannelList | 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.8 | DisplayString | read-only | This object identifies a list of channles/timeslots that will be assigned to this Protocol Managers data IFO's |
| ctDs1Ext | 1.3.6.1.4.1.52.4.1.2.7.2.2 | |||
| ctDs1ExtensionsTable | 1.3.6.1.4.1.52.4.1.2.7.2.2.1 | not-accessible | This table is an extension to the standard ds1 configuration table. It is a list of items that are pertinant to ds1 ports on a platform. There is one entry per ds1 physical port on the platform. | |
| ctDs1ExtensionsEntry | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1 | not-accessible | A ds1 extensions entry containing objects relating to the particular ds1 physical port. | |
| INT ctDs1ExtensionsEntryIndex | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.1 | INTEGER | read-only | A unique value for each ds1 physical port on the platform. |
| INT ctDs1ExtensionsNumInterfaces | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.2 | INTEGER | read-only | The number of interfaces on this physical port. This number inidicates the number of entries this physical port uses in the ifTable. |
| INT ctDs1ExtensionsToggleFracTable | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.3 | INTEGER | read-write | Setting this object to 1 will cause the Ds1 Fractional Table to be updated with the new values, as entered. Setting this object to 2, will cause the Ds1 Fractional Table to view as the table being entered. Setting this object to 3, will cause the Ds1 Fractional Table to be the table that is currently in use, regardless of any changes being entered. Setting this object to 4, will cause any changes that have been made to the Ds1 Fractional Table since the last update-table to be deleted. For physical ports that are of type synch, or for Ds1 ports that do not support the Ds1 Fractional Table, this object will have no affect, and will always return a 1. |
| INT ctDs1ExtensionsLineBuildOut | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.4 | INTEGER | read-write | The line build out setting for this ds1 physical port. Unknown indicates that the setting is neither readable or writable. |
| INT ctDs1ExtensionsCFADuration | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.5 | INTEGER | read-write | The length of time (in seconds), that the ds1 port will remain in the Carrier Failure Alarm state after the alarm condition has cleared. For those Ds1 ports not supporting Carrier Failure Alarm duration, this object always returns 1, and setting the object has no effect. |
| INT ctDs1ExtensionsDIEnable | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.6 | INTEGER | read-write | Enables or disables Drop and Insert functionality on a D/I WPIM. If enabled, all zero assigned timeslots will designate D/I interface channels, if disabled all zero channels will designate dummy channels as on a T1 or E1. |
| CTR ctDs1ExtensionsTotalValidIntervals | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.7 | Counter | read-only | The number of previous intervals for which valid data was collected for the DS1 mib, which is currently RFC1406. This counter is similar to RFC1406 dsx1ValidIntervals except that the count represents the total number of complete 15 minute intervals since the ds1 interface has been online, and does not stop at the 24 hour period. |
| INT wanDs1ExtensionsBertTestMode | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.8 | INTEGER | read-write | This object is used to request that a type of process be in control of the testing function. This is used to differentiate between automated test procedures and those manually controlled by a user. When read, this object reflects which type of process is actually in control of the testing function. The implementation is free to prioritize or deny requests in a proprietary manner. |
| INT wanDs1ExtensionsBertRun | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.9 | INTEGER | read-write | Controls the sending of test data over this physical port. The data is a pattern described by wanDs1ExtensionsBertTestPattern. |
| INT wanDs1ExtensionsBertCurrentResults | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.10 | INTEGER | read-only | Indicates the results of the testing for the last completed sampling period. A non-negative number is the error rate in bits per million bits. |
| INT wanDs1ExtensionsBertCumulativeResults | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.11 | INTEGER | read-only | Indicates the total number of errors since the testing was enabled. It is not a rate. |
| INT wanDs1ExtensionsBertPeakResults | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.12 | INTEGER | read-only | Indicates the highest value of wanDs1ExtensionsBertCurrentResults since the testing was enabled. A non-negative number is the error rate in bits per million bits. |
| INT wanDs1ExtensionsBertAverageResult | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.13 | INTEGER | read-only | Indicates the average value of wanDs1ExtensionsBertCurrentResults since the testing was enabled. A non-negative number is the error rate in bits per million bits. |
| INT wanDs1ExtensionsBertTestPattern | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.14 | INTEGER | read-write | This object is used to specify the pattern of the test data. |
| INT wanDs1ExtensionsBertSamplePeriod | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.15 | INTEGER | read-write | This object is the duration of time in seconds at which the current test results will be periodically written to wanDs1ExtensionsBertCurrentResults. The range is 1 to 3600, with a default value of 10. |
| CTR wanDs1ExtensionsBertNumPeriods | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.16 | Counter | read-only | The number of sampling periods that have elapsed during the current test run. |
| INT wanDs1ExtensionsBertTestTraps | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.17 | INTEGER | read-write | This object is used to enable or disable the sending of a trap at the conclusion of the measurement period. The trap will contain the information described by ctDs1BertCurrentResults. The default value is disabled. |
| INT wanDs1ExtensionsBertDataStatus | 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.18 | INTEGER | read-only | This object provides the operating status of the transmission of test data packets. |
| ctDs1WanDriverTable | 1.3.6.1.4.1.52.4.1.2.7.2.2.2 | not-accessible | This table is an extension to the standard ds1 configuration table. It is a list of items that are pertinant to the hdlc driver on a platform. There is one entry per ds1 physical port on the platform. | |
| ctDs1WanDriverEntry | 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1 | not-accessible | A ds1 wan driver entry containing objects relating to the particular ds1 physical port pertaining to a specific channel on the wan driver chip. | |
| INT ctDs1WanDriverEntryIndex | 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.1 | INTEGER | read-only | A unique value for each ds1 physical port on the platform. |
| INT ctDs1WanDriverChannelIndex | 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.2 | INTEGER | read-only | A unique value for each channel on a wan driver on the platform. |
| INT ctDs1WanDriverLineCode | 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.3 | INTEGER | read-write | This object controls the individual channels line coding on a wan driver device on the platform. |
| INT ctDs1WanDriverCRCBits | 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.4 | INTEGER | read-write | This object controls the individual channels CRC bits generation on a wan driver device on the platform. |
| ctRs232Ext | 1.3.6.1.4.1.52.4.1.2.7.2.3 | |||
| ctRs232ExtensionsTable | 1.3.6.1.4.1.52.4.1.2.7.2.3.1 | not-accessible | This table is an extension to the standard rs232-like mib. It is a list of items that are pertinant to rs232-like ports on a platform. There is one entry per synchronous physical port on the platform. | |
| ctRs232ExtensionsEntry | 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1 | not-accessible | A rs232-like extensions entry containing objects relating to the particular rs232-like physical port. | |
| INT ctRs232ExtensionsEntryIndex | 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.1 | INTEGER | read-only | A unique value for each rs232-like physical port on the platform. |
| INT ctRs232ExtensionsCTSEnable | 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.2 | INTEGER | read-write | This object indicates whether the platform should generate CTS. When disabled the platform will not generate CTS, when enabled, the platform will generate CTS. The actual state of the CTS line is available in the rs-232 like mib. |
| INT ctRs232ExtensionsDSREnable | 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.3 | INTEGER | read-write | This object indicates whether the platform should generate DSR. When disabled the platform will not generate DSR, when enabled, the platform will generate DSR. The actual state of the DSR line is available in the rs-232 like mib. |
| INT ctRs232ExtensionsRTSEnable | 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.4 | INTEGER | read-write | This object indicates whether the platform should generate RTS. When disabled the platform will not generate RTS, when enabled, the platform will generate RTS. The actual state of the RTS line is available in the rs-232 like mib. |
| INT ctRs232ExtensionsDTREnable | 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.5 | INTEGER | read-write | This object indicates whether the platform should generate DTR. When disabled the platform will not generate DSR, when enabled, the platform will generate DTR. The actual state of the DTR line is available in the rs-232 like mib. |
| ctFrDcp | 1.3.6.1.4.1.52.4.1.2.7.2.4 | |||
| frDcpCircuitTable | 1.3.6.1.4.1.52.4.1.2.7.2.4.1 | not-accessible | A table containing data compression information about specific Data Link Connection Identifiers and corresponding virtual circuit. This information is used to support the frCircuitTable following RFC-1315. | |
| frDcpCircuitEntry | 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1 | not-accessible | The data compression information regarding a single Data Link Connection Identifier. | |
| IND frDcpCircuitIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.1 | Index | read-only | The ifIndex value of ifEntry that this DCP virtual circuit object is layered onto. |
| DLC frDcpCircuitDlci | 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.2 | DLCI | read-only | The Data Link Connection Identifier for this DCP virtual circuit object. |
| INT frDcpCircuitEnable | 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.3 | INTEGER | read-write | Indicates whether data compression should take place on this particular end side virtual circuit. |
| INT frDcpCircuitStatus | 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.4 | INTEGER | read-only | On indicates that the compression has been successfully negotiated and is operating. Off indicates that the compression negotiation has failed and compression is not operating at this time, or compression has been terminated by either peer. |
| OCT frDcpCircuitRatio | 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.5 | OCTET STRING | read-only | The ratio of uncompressed to compressed transmitted data. If the data compression status is off, 1:1 will be displayed. |
| ctDDSExt | 1.3.6.1.4.1.52.4.1.2.7.2.5 | |||
| ctDDSConfigTable | 1.3.6.1.4.1.52.4.1.2.7.2.5.1 | not-accessible | The DDS Configuration Table | |
| ctDDSConfigEntry | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1 | not-accessible | An Entry in the DDS Configuration Table | |
| INT ctDDSLineIndex | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.1 | INTEGER | read-only | A unique value for each ds1 physical port on the platform. |
| INT ctDDSIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.2 | INTEGER | read-only | Index associated with this dds physical port |
| INT ctDDSLineMode | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.3 | INTEGER | read-write | DDS-PRI is full duplex 56k link, No framing in loop data so loop speed is also 56k. Data stream: --d1 d2 d3 d4 d5 d6 d7-- DDS-SC is also full duplex 56k link, requires framing bits to distinguish between primary and secondary channels. --d1 d2 d3 d4 d5 d6 d7 F C/S-- where F is framing bit and C/S for secondary channel as well as used for control bit. With these two extra bits the loop speed is increased to 72k. primary channel rate is 56k. DDS-CC is full duplex 64k link. Does not require framing bit but uses a same format as SC, nineth bit position is lumped with primary channel and not used for control. Loop speed is 72k, Primary channel rate is 64k. --d1 d2 d3 d4 d5 d6 d7 F d8-- |
| INT ctDDSLineCoding | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.4 | INTEGER | read-write | This object describes the variety of Zero Code suppression on this interface. JBZS refers to Jammed Bit Zero suppresion, which forces a 1 bit every 8 bit periods. None refers to a mode in which some other means is used to insure pulse density requirements. |
| INT ctDDSLoopbackConfig | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.5 | INTEGER | read-write | This variable represents the loopback configuration of the DDS interface. ddsNoLoop means the interface is not in loopback state, ddsLocalLoop means the signal is transmitted and looped back to the same interface, ddsLineLoop means the received signal at this interface does not go through the device but is looped back out, and ddsOtherLoop represents a loop not defined here. |
| INT ctDDSLineStatus | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.6 | INTEGER | read-only | This variable describes the current operational status of DDS line. |
| INT ctDDSTxClockSource | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.7 | INTEGER | read-write | The source of Transmit clock. 'ddsLoopTiming' indicates that the recovered receive clock is used as transmit clock. 'ddsLocalTiming' indicates that a local clock source is used. 'ddsThroughTiming' indicates that recovered receive clock from another interface is used as transmit clock. |
| INT ctDDSPortInSpeed | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.8 | INTEGER | read-only | This variable describes the current operational receive speed of DDS line. It is a read only value based entirely on DDS type (CC or PRI). |
| INT ctDDSPortOutSpeed | 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.9 | INTEGER | read-only | This variable describes the current operational transmit speed of DDS line. It is a read only value based entirely on DDS type CC or PRI |
| ctPPPExt | 1.3.6.1.4.1.52.4.1.2.7.2.6 | |||
| ctPppCountersTable | 1.3.6.1.4.1.52.4.1.2.7.2.6.1 | not-accessible | Table containing the parameters for the local PPP entity related to the counters and timers. | |
| ctPppCountersEntry | 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1 | not-accessible | PPP counter/timer information for a particular PPP link. | |
| INT ctPppCountersIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.1 | INTEGER | read-write | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| INT ctPppCountersMaxTerminate | 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.2 | INTEGER | read-write | MaxTerminate indicates the number of Terminate- Request packets sent without receiving a Terminate-Ack before assuming that the peer in unable to respond. |
| INT ctPppCountersMaxConfigure | 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.3 | INTEGER | read-write | MaxConfigure indicates the number of Configure- Request packets sent without receiving a Configure-Ack, Configre-Nak or Configure-Reject before assuming that the peer in unable to respond. |
| INT ctPppCountersMaxFailure | 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.4 | INTEGER | read-write | MaxFailure indicates the number of Configure-Nak packets sent without sending a Configure-Ack before assuming that the configuration is not converging. Any further Configure-Reject packets for peer requested options are converted to Configure-Reject packets, and locally desires options are no longer appended. |
| INT ctPppCountersRestartTimer | 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.5 | INTEGER | read-write | The Restart timer is used to time transmissions of Configure-Request and Terminate-Request packets. Expiration of the Restart-Timer causes a Timeout event, and retransmission of the corresponding Configure-Request or Terminate-Request packet. |
| ctPppLcpExtTable | 1.3.6.1.4.1.52.4.1.2.7.2.6.2 | not-accessible | Table containing the parameters for the local PPP entity related to the counters and timers. | |
| ctPppLcpExtEntry | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1 | not-accessible | PPP LCP configurationinformation for a particular PPP link. | |
| INT ctPppLcpExtIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.1 | INTEGER | read-write | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| INT ctPppLcpExtAuthenticationProt | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.2 | INTEGER | read-only | Enables a particular authentication protocol on this PPP link(now modified for read-only. |
| INT ctPppLcpExtQualityProt | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.3 | INTEGER | read-write | Enables a particular link-quality protocol on this PPP link. |
| INT ctPppLcpExtPFC | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.4 | INTEGER | read-write | Enables protocol field compression on this PPP link. |
| INT ctPppLcpExtACFC | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.5 | INTEGER | read-write | Enables address and control field compression on this PPP link. |
| INT ctPppLcpExtSelfDescribePadding | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.6 | INTEGER | read-write | This Configuration Option provides a method for an implementation to indicate to the peer that it understands self-describing pads when padding is added at the end of the PPP Information field. |
| INT ctPppLcpExtCallback | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.7 | INTEGER | read-write | This Configuration Option provides a method for an implementation to request a dial-up peer to call back. |
| INT ctPppLcpExtCompoundFrames | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.8 | INTEGER | read-write | This Configuration Option provides a method for an implementation to send multiple PPP encapsulated packets within the same frame. |
| INT ctPppLcpExtMru | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.9 | INTEGER | read-write | Enables and disables Mru status. |
| INT ctPppLcpExtAccm | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.10 | INTEGER | read-write | Enables and disables Accm status. |
| INT ctPppLcpExtEchoRequest | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.11 | INTEGER | read-write | A zero indicated no Echo Request and any other value provides an interval to send Echo-Requests to the Peer. The Echo-Request provides a Data Link Layer loopback mechanism for use in exercising both directions of the link. This is useful in debugging, link quality determination. LCP MUST be in the OPENED state for an Echo-Request to occur. |
| INT ctPppLcpExtReplyCounter | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.12 | INTEGER | read-only | Increments a counter if the Local Device correctly received an Echo-Reply from the Peer. LCP MUST be in the OPENED state for an Echo-Reply to occur. |
| INT ctPppLcpExtMpCapable | 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.13 | INTEGER | read-write | Multilink Protocol (MP) option selector. Set to a value of one when MP support is desired otherwise set to a value of two. The default value is two. When set to two the attempt is made to negotiate MP support. MP support is symmetrical. |
| ctPppBncpExtTable | 1.3.6.1.4.1.52.4.1.2.7.2.6.3 | not-accessible | Table containing the parameters for the local PPP entity related to the counters and timers. | |
| ctPppBncpExtEntry | 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1 | not-accessible | PPP LCP configuration information for a particular PPP link. | |
| INT ctPppBncpExtIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1.1 | INTEGER | read-write | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| INT ctPppBncpExtCrcStatus | 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1.2 | INTEGER | read-write | Enables and disables CRC status. First our platform must support CRC. If the platform does, then setting to disabled will not send CRC. The default is enabled, which sends CRC. |
| ctPppMpExtTable | 1.3.6.1.4.1.52.4.1.2.7.2.6.4 | not-accessible | Table containing the parameters for the local PPP entity related to the counters and timers. | |
| ctPppMpExtEntry | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1 | not-accessible | PPP LCP configurationinformation for a particular PPP link. | |
| INT ctPppMpExtIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.1 | INTEGER | read-write | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| INT ctPppLcpExtMpLUT | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.2 | INTEGER | read-write | Used to set the Line Utilization Threshold (LUT) % value to compare against the linear weighted percentage by which to determine when more/less bandwidth is to be added/removed. Linear weighting is averaged over the period of time specified by ctPppLcpExtMpHistoryTime. |
| INT ctPppLcpExtMpHistoryTime | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.3 | INTEGER | read-write | Used to set the history time value in seconds for the number of line utilization reading(s) desired to compute the average line utilization. That is to say, it specifies the window size over which to compute the average line utilization. |
| INT ctPppLcpExtMpMoreBW | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.4 | INTEGER | read-write | Used to set the number of consecutive line utilization average readings that must exceed ctPppLcpExtMpLUT as a condition of when to increase the bandwidth if more BW is permitted. |
| INT ctPppLcpExtMpLessBW | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.5 | INTEGER | read-write | Used to set the number of consecutive line utilization average readings that must fall below ctPppLcpExtMpLUT as a condition of when to remove possible previously added bandwidth. |
| INT ctPppLcpExtMpMaxChannels | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.6 | INTEGER | read-write | Used to set the maxium number of channels an MP capable connection is allowed. |
| INT ctPppLcpExtMpChannelsToAdd | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.7 | INTEGER | read-write | Used to set the number of additional channel(s) to increment by whenever the need for more bandwidth is determined. |
| INT ctPppLcpExtMpChannelsToRemove | 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.8 | INTEGER | read-write | Used to set the number of channel(s) to decrement by whenever the need for possible previously added bandwidth is determined to no longer be needed. |
| ctPppEcpExtTable | 1.3.6.1.4.1.52.4.1.2.7.2.6.5 | not-accessible | Table containing the parameters for the local PPP entity related to the encrpytion control protocol. | |
| ctPppEcpExtEntry | 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1 | not-accessible | PPP ECP configuration information for a particular PPP link. | |
| INT ctPppEcpExtIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.1 | INTEGER | read-write | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| STR ctPppEcpKey | 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.2 | DisplayString | read-write | A 56-bit key (14 hex characters) used for the DES encryption. |
| STR ctPppEcpIV | 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.3 | DisplayString | read-write | A 64-bit initialization vector (16 hex characters) used for the DES encryption in CBC mode. |
| ctWanalyzer | 1.3.6.1.4.1.52.4.1.2.7.2.7 | |||
| ctWanalyzerTable | 1.3.6.1.4.1.52.4.1.2.7.2.7.1 | not-accessible | Table containing the parameters for the local Wanalyzer entity related to the configured Protocol. | |
| ctWanalyzerEntry | 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1 | not-accessible | Information for a particular interface. | |
| INT ctWanalyzerIfIndex | 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.1 | INTEGER | read-write | The ifIndex of the interface. This is the index of this entry in the ifTable. |
| INT ctWanalyzerEnabled | 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.2 | INTEGER | read-write | This Persistent Object is a flag which indicates whether or not the WANalyzer is enabled or disabled. Upon system initialization this flag defaults to disabled unless a value for this object is found in NVRAM. |
| INT ctWanalyzerMaxEntries | 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.3 | INTEGER | read-write | This Persistent Object is an integer greater than 1 which specifies the maximum total number of entries which the table will handle. When the WANalyzer is enabled this value defaults to a value dependent on the implementation unless a value is found in NVRAM. |
| INT ctWanalyzerClearAll | 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.4 | INTEGER | read-write | When set to 2, the entire table of entries is cleared. Upon clearing of the table, this value is reset to 1. This object is not present if the WANalyzer is disabled. |
| INT ctWanalyzerClearInterface | 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.5 | INTEGER | read-write | When set to 2, all entries for this MIB-II interface index will be removed from the table. Upon complete removal of those entries, this value is reset to 1. This object is not present if the WANalyzer is disabled. |
| INT ctWanalyzerDisplayInterface | 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.6 | INTEGER | read-write | When set to a valid MIB-II interface number, the table displays only those entries in the table which were received from that MIB-II interface. This value is set to -1 upon initialization and indicates that entries from all interfaces will be displayed. This object is not present if the WANalyzer is disabled. |
| INT ctWanalyzerCurrEntries | 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.7 | INTEGER | read-only | A non-negative integer indicating the current number of entries in the table. This object is not present if the WANalyzer is disabled. |
| wanalyzerMessageTable | 1.3.6.1.4.1.52.4.1.2.7.2.7.2 | not-accessible | A table containing all of the message entries for this device. If the WANalyzer is disabled, this table will not be present. | |
| wanalyzerEntry | 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1 | not-accessible | A message entry in the WANalyzer table corresponding to a particular interface in a particular instance. | |
| INT wanMessageIndex | 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.1 | INTEGER | read-only | An integer between 1 and wanalyzerMaxEntries which indicates the overall position this entry has in the WANalyzer table. |
| INT wanMessageInterfaceIndex | 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.2 | INTEGER | read-only | The MIB-II interface index representing the interface which sent this message. |
| STR wanMessageDate | 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.3 | DisplayString | read-only | The date when this message was received by the WANalyzer in the standard MMDDYY format. |
| STR wanMessageTime | 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.4 | DisplayString | read-only | The time of day when this message was received by the WANalyzer in the standard HHMMSS format. |
| INT wanMessageCode | 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.5 | INTEGER | read-only | An enumerated value representing the nature of the debug message sent by the interface. |
| ctDs1Alarms | 1.3.6.1.4.1.52.4.1.2.7.2.8 | |||
| ds1AlarmsGlobalConfigGroup | 1.3.6.1.4.1.52.4.1.2.7.2.8.1 | |||
| INT ds1AlarmGlobalAdmin | 1.3.6.1.4.1.52.4.1.2.7.2.8.1.1 | INTEGER | read-write | Used to enable and disable the DS1 Alarm Monitoring Application for all DS1 circuits on the device. |
| INT ds1AlarmGlobalAutoRecovery | 1.3.6.1.4.1.52.4.1.2.7.2.8.1.2 | INTEGER | read-write | Used to enable and disable the DS1 Alarm Automatic Recovery feature for all DS1 circuits on the device. For those devices that support ds1 alarm monitoring, but do not support the automatic recovery feature, this object always returns disabled, and performs no action when written. |
| INT ds1AlarmGlobalTrapEnable | 1.3.6.1.4.1.52.4.1.2.7.2.8.1.3 | INTEGER | read-write | Used to enable and disable the DS1 Alarm SNMP Trap generation feature for all DS1 circuits on the device. This object operates in conjunction with configuration of objects in the ctron-trap-mib.txt |
| INT ds1AlarmGlobalESCount | 1.3.6.1.4.1.52.4.1.2.7.2.8.1.4 | INTEGER | read-write | Used in conjuction with ctDs1AlarmESInterval to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval. |
| INT ds1AlarmGlobalESInterval | 1.3.6.1.4.1.52.4.1.2.7.2.8.1.5 | INTEGER | read-write | Used in conjuction with ds1AlarmGlobalESCount to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval. |
| INT ds1AlarmGlobalBPVErrorRate | 1.3.6.1.4.1.52.4.1.2.7.2.8.1.6 | INTEGER | read-write | Used to specify the negative exponent of 10, used in monitoring Bipolar Violations (Code Violations for E1) over intervals defined by ds1AlarmGlobalBPVInterval. For example, for a ds1AlarmGlobalBPVErrorRate value of 6 used with a ds1AlarmGlobalBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written. |
| INT ds1AlarmGlobalBPVInterval | 1.3.6.1.4.1.52.4.1.2.7.2.8.1.7 | INTEGER | read-write | Used to specify the interval, used in monitoring Bipolar Violations (Code Violations for E1) with thresholds defined by ds1AlarmGlobalBPVErrorRate. For example, for a ds1AlarmGlobalBPVErrorRate value of 6 used with a ds1AlarmGlobalBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not detect bipolar violations, this object always returns the default, and performs no action when written. |
| INT ds1AlarmGlobalManualRecovery | 1.3.6.1.4.1.52.4.1.2.7.2.8.1.8 | INTEGER | read-write | To cause a manual recovery to occur on all Ds1 circuits, this object is set to a 1. It is always read as a 1. The recovery will occur only when automatic recovery is disabled. |
| ds1AlarmConfigTable | 1.3.6.1.4.1.52.4.1.2.7.2.8.2 | not-accessible | Table containing objects used to configure DS1 alarm functionality on a per DS1 basis. | |
| ds1AlarmConfigEntry | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1 | not-accessible | A description of a single entry. | |
| INT ds1PhysNum | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.1 | INTEGER | read-only | The value for this object is equal to the value of a unique physical connection identifier associated with this DS1 which is clearly labeled on the device. For those products that do not have a DS1 identifier labeled on the device, the value for this object is the same as rfc1406 dsx1LineIndex. |
| INT ds1AlarmAdmin | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.2 | INTEGER | read-write | Used to enable and disable the DS1 Alarm Monitoring Application for this DS1 circuit. |
| INT ds1AlarmAutoRecovery | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.3 | INTEGER | read-write | Used to enable and disable the DS1 Alarm Automatic Recovery feature for this DS1 circuit. For those devices that support ds1 alarm monitoring, but do not support the automatic recovery feature, this object always returns disabled, and performs no action when written. |
| INT ds1AlarmTrapEnable | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.4 | INTEGER | read-write | Used to enable and disable the DS1 Alarm SNMP Trap generation feature for this DS1 circuit. This object operates in conjunction with configuration of objects in the ctron-trap-mib.txt |
| INT ds1AlarmESCount | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.5 | INTEGER | read-write | Used in conjuction with ctDs1AlarmESInterval to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval. |
| INT ds1AlarmESInterval | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.6 | INTEGER | read-write | Used in conjuction with ctDs1AlarmESCount to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval. |
| INT ds1AlarmBPVErrorRate | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.7 | INTEGER | read-write | Used to specify the negative exponent of 10, used in monitoring Bipolar Violations (Code Violations for E1) over intervals defined by ds1AlarmBPVInterval. For example, for a ds1AlarmBPVErrorRate value of 6 used with a ds1AlarmBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written. |
| INT ds1AlarmBPVInterval | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.8 | INTEGER | read-write | Used to specify the interval, used in monitoring Bipolar Violations (Code Violations for E1) with thresholds defined by ds1AlarmBPVErrorRate. For example, for a ds1AlarmBPVErrorRate value of 6 used with a ds1AlarmBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written. |
| INT ds1AlarmManualRecovery | 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.9 | INTEGER | read-write | To cause a manual recovery to occur, this object is set to a 1. It is always read as a 1. The recovery will occur only when automatic recovery is disabled. |
| ctIPPQFilters | 1.3.6.1.4.1.52.4.1.2.7.2.9 | |||
| ipPQConfigGroup | 1.3.6.1.4.1.52.4.1.2.7.2.9.1 | |||
| INT ipPQAdmin | 1.3.6.1.4.1.52.4.1.2.7.2.9.1.1 | INTEGER | read-write | Used to enable and disable the IP Priority Queue Forwarding Application. |
| INT iPPQMaxEntries | 1.3.6.1.4.1.52.4.1.2.7.2.9.1.2 | INTEGER | read-only | Returns the maximum number of IP address entries supported by the IP Priority Queue application on this device. |
| INT iPPQNumEntries | 1.3.6.1.4.1.52.4.1.2.7.2.9.1.3 | INTEGER | read-only | Get the number of IP address entries currently programmed in the ipPQAddressTable. |
| IP iPPQAddAddress | 1.3.6.1.4.1.52.4.1.2.7.2.9.1.4 | IpAddress | read-write | Add an IP address to the ipPQAddressTable. Always read as a 0.0.0.0. |
| IP iPPQDelAddress | 1.3.6.1.4.1.52.4.1.2.7.2.9.1.5 | IpAddress | read-write | Delete an IP address from the ipPQAddressTable. Always read as a 0.0.0.0. |
| ipPQAddressTable | 1.3.6.1.4.1.52.4.1.2.7.2.9.2 | not-accessible | Table containing IP addresses, used in an IP Priority Queue Forwarding function. | |
| ipPQAddressEntry | 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1 | not-accessible | A description of a single entry. | |
| INT ipPQAddressId | 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1.1 | INTEGER | read-only | A unique value identifying an element in a sequence of IP PQ address entries. |
| IP ipPQIPAddress | 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1.2 | IpAddress | read-only | Returns an IP address associated with a specific entry in this table. |
| ctDs3Ext | 1.3.6.1.4.1.52.4.1.2.7.2.10 | |||
| ctDs3ExtensionsTable | 1.3.6.1.4.1.52.4.1.2.7.2.10.1 | not-accessible | This table is an extension to the standard ds3 configuration table. It is a list of items that are pertinant to ds3 ports on a platform. There is one entry per ds3 physical port on the platform. | |
| ctDs3ExtensionsEntry | 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1 | not-accessible | A ds3 extensions entry containing objects relating to the particular ds3 physical port. | |
| INT ctDs3ExtensionsEntryIndex | 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.1 | INTEGER | read-only | A unique value for each ds3 physical port on the platform. |
| INT ctDs3ExtensionsNumInterfaces | 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.2 | INTEGER | read-only | The number of interfaces on this physical port. This number inidicates the number of entries this physical port uses in the ifTable. |
| INT ctDs3ExtensionsLineBuildOut | 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.3 | INTEGER | read-write | The line build out setting for this ds3 physical port. Unknown indicates that the setting is neither readable or writable. |
RFC description
Cabletron Systems remote access MIB for managing dial-up and remote connectivity features on Cabletron devices.
Start monitoring Cabletron/Enterasys remote-access server (dial-in/ISDN) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.