| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ciscoWirelessExpMIB | 1.3.6.1.4.1.9.10.52 | | | This is the MIB Module for the Cisco Wireless Radio
Point to Point experimental components.
Glossary
The following terms are used in the MIB definitions below.
Radio Card: The line card that provides the wireless
communication features.
Radio Link: The bi-directional wireless link that exists
between two communicating radio cards.
Radio PHY: Represents the transmission characteristics of the
Radio Link.
RF Unit: The Radio Frequency components and the associated antennas.
Radio System: Radio card and RF unit(s).
Cisco Wireless Radio Experimental MIB Organization
The Cisco Wireless Radio Experimental MIB provides the following
management groups :
When the draft-ietf-entmib-v2-03.txt gets finalized the Radio Frequency
Group will be moved into that MIB.
When the CISCO-IMAGE-MIB.my gets updated to include the image
capabilities, the Image Group will be migrated into that MIB.
When the CISCO-LED-MIB.my becomes available and supports the
functionality the LED group needs, the LED group will be
migrated into that.
o. Radio Frequency Resource Group
This contains information about the Radio frequency
transmission and reception resources available on the
system. This group determines the portions of the
radio spectrum at which the radio subsystem can
operate.
This group in conjunction with the radio PHY group
determine the acutal spectrum that gets used for
communications.
o. Image Group
This provides facilities to manage radio line card's
firmware image file URL's in router's image repository.
It also provides access to the image details.
o. LED Group
This group provides information about LEDs available
on the line card.
o. Duplexor Group
This group provides information about the Duplexors
installed in the RF resources. |
| cwrRadioExpMibObjects | 1.3.6.1.4.1.9.10.52.1 | | | |
| cwrRadioFreqEntityGroup | 1.3.6.1.4.1.9.10.52.1.1 | | | |
| cwrRfEntityTable | 1.3.6.1.4.1.9.10.52.1.1.1 | | not-accessible | This table contains information about the radio
frequency resources available for use on the system. |
| cwrRfEntityEntry | 1.3.6.1.4.1.9.10.52.1.1.1.1 | | not-accessible | This represents one entry in the cwrRfEntityTable. This table is
largely a read only table which provides details on the radio
frequency resources available on the system. Physically
each RF resource may be realized by one antenna and its
associated control hardware.
But a single antenna and its associated hardware may act
as more than 1 RF resource.
A Duplexor is a mechanical device, that acts as a band pass filter
when installed in an RF resource.
Normally a RF resource is capable of operating over a wide
frequency range. To operate at restricted frequencies,
the user has to own that part of the frequency spectrum.
Since the user may not own parts of
the frequency spectrum over which the RF resource may operate, a
Duplexor is installed in the RF resource. This restricts the
RF resource to operate in the passband defined by the Duplexor.
In this table the Duplexor's are identified by an index into the
cwrDuplexorTable.
It is indexed by the ifIndex and cwrRfEntityIndex. |
| I32 cwrRfEntityIndex | 1.3.6.1.4.1.9.10.52.1.1.1.1.1 | Integer32 | not-accessible | This object represents the index of this entry in the
cwrRfEntityTable. |
| U32 cwrRfSwRevision | 1.3.6.1.4.1.9.10.52.1.1.1.1.2 | Unsigned32 | read-only | This object represents the software revision number
of controlling the RF subsystem. |
| U32 cwrRfAssemblyPartNumberClass | 1.3.6.1.4.1.9.10.52.1.1.1.1.3 | Unsigned32 | read-only | This object represents the assembly part number class of the RF
subsystem. |
| U32 cwrRfAssemblyPartNumberBase | 1.3.6.1.4.1.9.10.52.1.1.1.1.4 | Unsigned32 | read-only | This object represents the assembly part number base of the RF
subsystem. |
| U32 cwrRfAssemblyPartNumberVersion | 1.3.6.1.4.1.9.10.52.1.1.1.1.5 | Unsigned32 | read-only | This object represents the assembly part number version of the RF
subsystem. |
| U32 cwrRfBoardPartNumberClass | 1.3.6.1.4.1.9.10.52.1.1.1.1.6 | Unsigned32 | read-only | This object represents the board part number class of the RF
subsystem. |
| U32 cwrRfBoardPartNumberBase | 1.3.6.1.4.1.9.10.52.1.1.1.1.7 | Unsigned32 | read-only | This object represents the board part number base of the RF
subsystem. |
| U32 cwrRfBoardPartNumberVersion | 1.3.6.1.4.1.9.10.52.1.1.1.1.8 | Unsigned32 | read-only | This object represents the board part number version of the RF
subsystem. |
| STR cwrRfBoardRevision | 1.3.6.1.4.1.9.10.52.1.1.1.1.9 | DisplayString | read-only | This object represents the board revision of the RF subsystem. |
| STR cwrRfSerialNumber | 1.3.6.1.4.1.9.10.52.1.1.1.1.10 | DisplayString | read-only | This object represents the serial number of the RF subsystem. |
| DAT cwrRfManfDate | 1.3.6.1.4.1.9.10.52.1.1.1.1.11 | DateAndTime | read-only | This object represents the manufacturing date of the RF subsystem. |
| I32 cwrRfVendorId | 1.3.6.1.4.1.9.10.52.1.1.1.1.12 | Integer32 | read-only | This object represents the Radio frequency device vendor ID. |
| I32 cwrRfDuplexorIndex | 1.3.6.1.4.1.9.10.52.1.1.1.1.13 | Integer32 | read-only | This object represents the index into cwrDuplexorTable.
This index identifies the Duplexor associated with this
RF resource. |
| cwrIntFreqEntityTable | 1.3.6.1.4.1.9.10.52.1.1.2 | | not-accessible | This table contains information about the intermediate frequency
subsystem on the radio card. |
| cwrIntFreqEntityEntry | 1.3.6.1.4.1.9.10.52.1.1.2.1 | | not-accessible | This represents one entry in the cwrIntFreqEntityTable.
This table is largely a read only table which provides
details on the intermediate frequency subsystem available
on the radio card.
It is indexed by the ifIndex. |
| U32 cwrIfAssemblyPartNumberClass | 1.3.6.1.4.1.9.10.52.1.1.2.1.1 | Unsigned32 | read-only | This object represents the assembly part number class of the IF
subsystem. |
| U32 cwrIfAssemblyPartNumberBase | 1.3.6.1.4.1.9.10.52.1.1.2.1.2 | Unsigned32 | read-only | This object represents the assembly part number base of the IF
subsystem. |
| U32 cwrIfAssemblyPartNumberVersion | 1.3.6.1.4.1.9.10.52.1.1.2.1.3 | Unsigned32 | read-only | This object represents the assembly part number version of the IF
subsystem. |
| U32 cwrIfBoardPartNumberClass | 1.3.6.1.4.1.9.10.52.1.1.2.1.4 | Unsigned32 | read-only | This object represents the board part number class of the IF
subsystem. |
| U32 cwrIfBoardPartNumberBase | 1.3.6.1.4.1.9.10.52.1.1.2.1.5 | Unsigned32 | read-only | This object represents the board part number base of the IF
subsystem. |
| U32 cwrIfBoardPartNumberVersion | 1.3.6.1.4.1.9.10.52.1.1.2.1.6 | Unsigned32 | read-only | This object represents the board part number version of the IF
subsystem. |
| STR cwrIfBoardRevision | 1.3.6.1.4.1.9.10.52.1.1.2.1.7 | DisplayString | read-only | This object represents the board revision of the IF subsystem. |
| STR cwrIfSerialNumber | 1.3.6.1.4.1.9.10.52.1.1.2.1.8 | DisplayString | read-only | This object represents the serial number of the IF subsystem. |
| DAT cwrIfManfDate | 1.3.6.1.4.1.9.10.52.1.1.2.1.9 | DateAndTime | read-only | This object represents the manufacturing date of the IF subsystem. |
| I32 cwrIfVendorId | 1.3.6.1.4.1.9.10.52.1.1.2.1.10 | Integer32 | read-only | This object represents the IF vendor ID. |
| U32 cwrIfSwRevision | 1.3.6.1.4.1.9.10.52.1.1.2.1.11 | Unsigned32 | read-only | This object represents the IF software revision. |
| cwrRadioImageGroup | 1.3.6.1.4.1.9.10.52.1.2 | | | |
| cwrImageTable | 1.3.6.1.4.1.9.10.52.1.2.1 | | not-accessible | This table provides facilities to manage the firmware
images that the router will use to configure the radio
line cards.
When images need to be downloaded, the software will
search this list starting from the first, for an image whose
capabilities match the configuration specified in the
cwrRadioBaseTable and the cwrRadioPhyTable and download that image
to the appropriate hardware component.
Insertion into the table at arbitrary points is not supported.
Any new image URL added to this table will be inserted at index
1 only.
Also note that an image gets downloaded to the hardware only when
when a radio link is administratively enabled. |
| cwrImageEntry | 1.3.6.1.4.1.9.10.52.1.2.1.1 | | not-accessible | This represents one entry in the cwrImageTable. |
| I32 cwrImageIndex | 1.3.6.1.4.1.9.10.52.1.2.1.1.1 | Integer32 | not-accessible | This represents the one entry in this table. It also represents
the search order. When images need to be downloaded to the
hardware, the images are searched in the order of this index
for an image that matches the hardware capabilities and uses it. |
| STR cwrImageNameUrl | 1.3.6.1.4.1.9.10.52.1.2.1.1.2 | DisplayString | read-write | This object is the name of the image in the
Universal Resource Locator (URL) format.
This URL will be used to access the image when needed. |
| INT cwrImageState | 1.3.6.1.4.1.9.10.52.1.2.1.1.3 | INTEGER | read-only | This represents the state of the image.
image_invalid(1): If the image could not be accessed for any reason.
image_valid(2) : Image accessible and available for use. |
| U32 cwrImageSize | 1.3.6.1.4.1.9.10.52.1.2.1.1.4 | Unsigned32 | read-only | This represents the size of the image in bytes. |
| U32 cwrImageChipClass | 1.3.6.1.4.1.9.10.52.1.2.1.1.5 | Unsigned32 | read-only | This represents the class of chips onto which this image may be
loaded. |
| U32 cwrImageChipType | 1.3.6.1.4.1.9.10.52.1.2.1.1.6 | Unsigned32 | read-only | This represents the download method to use. |
| U32 cwrImageCapability1 | 1.3.6.1.4.1.9.10.52.1.2.1.1.7 | Unsigned32 | read-only | This represents a bitmask.
The bit mask identifies the capabilities of
this image. See also cwrImageCapability2. |
| U32 cwrImageCapability2 | 1.3.6.1.4.1.9.10.52.1.2.1.1.8 | Unsigned32 | read-only | This represents a bitmask.
The bit mask identifies the capabilities of
this image in addition to cwrImageCapability1. |
| U32 cwrImageVersion | 1.3.6.1.4.1.9.10.52.1.2.1.1.9 | Unsigned32 | read-only | This represents the version number of this image. |
| STR cwrImageTag | 1.3.6.1.4.1.9.10.52.1.2.1.1.10 | DisplayString | read-only | This object is the tag string associated with the image.
Normally used to trace the source code used to generate
this image. |
| INT cwrImageOp | 1.3.6.1.4.1.9.10.52.1.2.1.1.11 | INTEGER | read-write | This object represents the operation to be performed on the
identified image.
nop(0) - This value will be returned when this object is
read.
add(1) - Will add the image URL, as the first entry in the image
table.
delete(2) - Will delete the specified ULR from the image table.
move(3) - Will make the image specified by the URL the first entry
in the imageTable. |
| cwrRadioLedGroup | 1.3.6.1.4.1.9.10.52.1.3 | | | |
| cwrLedTable | 1.3.6.1.4.1.9.10.52.1.3.1 | | not-accessible | Entity (Light emitting diode) LED information. For each LED on the
entity, an entry will exist in this table, describing the location
and current status of that LED. |
| cwrLedEntry | 1.3.6.1.4.1.9.10.52.1.3.1.1 | | not-accessible | An entry in the table, containing the LED information
about the entity. The entPhysicalIndex identifies
the entity on which the Led's are present. |
| INT cwrLedIndex | 1.3.6.1.4.1.9.10.52.1.3.1.1.1 | INTEGER | not-accessible | For a given entPhysicalIndex, this index value uniquely identifies
an entry in the cwrLedTable. |
| STR cwrLedName | 1.3.6.1.4.1.9.10.52.1.3.1.1.2 | DisplayString | read-only | The label of the LED on the physical entity or a textual
description to identify the usage of the LED. |
| I32 cwrLedVerticalPosition | 1.3.6.1.4.1.9.10.52.1.3.1.1.3 | Integer32 | read-only | The position of the LED in the entity. It is counted from
top to bottom. |
| I32 cwrLedHorizontalPosition | 1.3.6.1.4.1.9.10.52.1.3.1.1.4 | Integer32 | read-only | The position of the LED in the entity. It is counted from
from left to right. |
| INT cwrLedMode | 1.3.6.1.4.1.9.10.52.1.3.1.1.5 | INTEGER | read-write | This objects specifies the desired mode of LED updates.
automatic(1) and latched(2) are settings used by the software
to determine how the LED should be updated.
The others are for diagnostic purposes. The LED will be turned on
or off as specified by the other (3-8) settings.
The modes mean the following:
automatic(1): The system updates the LED according to the
default settings for that entity.
latched(2): Once the LED is turned on, user has to turn it off.
This applies only to alarm LEDs.
forceOff(3): Force the LED off.
forceSolidGreen(4): Force the LED to be solid green in on state.
forceSolidYellow(5):Force the LED to be solid Yellow in on state
forceBlinkGreen(6): Force the LED to blink in Green.
forceBlinkYellow(7):Force the LED to blink in Yellow.
forceBlinkBoth(8): Force the LED to blink Yellow and
Green alternatively. |
| INT cwrLedCurrentColor | 1.3.6.1.4.1.9.10.52.1.3.1.1.6 | INTEGER | read-only | Indicates the current color of the LED. |
| cwrRadioDuplexorGroup | 1.3.6.1.4.1.9.10.52.1.4 | | | |
| cwrDuplexorTable | 1.3.6.1.4.1.9.10.52.1.4.1 | | not-accessible | This table contains information about the Duplexors
available for use on the system. |
| cwrDuplexorEntry | 1.3.6.1.4.1.9.10.52.1.4.1.1 | | not-accessible | This represents one entry in the cwrDuplexorTable. This table
provides details on the Duplexors available on the system.
It is indexed by the ifIndex and cwrDuplexorIndex. |
| I32 cwrDuplexorIndex | 1.3.6.1.4.1.9.10.52.1.4.1.1.1 | Integer32 | not-accessible | This object represents the index of this entry in the
cwrDuplexorTable. |
| STR cwrDuplexorCiscoPartNumber | 1.3.6.1.4.1.9.10.52.1.4.1.1.2 | DisplayString | read-write | This object represents the Cisco part number for this Duplexor. |
| STR cwrDuplexorLoPassbandRange | 1.3.6.1.4.1.9.10.52.1.4.1.1.3 | DisplayString | read-write | This object represents the low frequency range that
this Duplexor will pass through without any attenuation.
All low frequencies outside this
range will be attenuated to a level such that an RF resource that
uses this Duplexor will be unable to transmit or receive those
frequencies. |
| STR cwrDuplexorHiPassbandRange | 1.3.6.1.4.1.9.10.52.1.4.1.1.4 | DisplayString | read-write | This object represents the high frequency range
that this Duplexor will pass through without any
attenuation. All high frequencies outside this
range will be attenuated to a level such that an RF resource that
uses this Duplexor will be unable to transmit or receive those
frequencies. |
| INT cwrDuplexorReceivePassband | 1.3.6.1.4.1.9.10.52.1.4.1.1.5 | INTEGER | read-write | This object indicates which of the two passbands are being used
to receive transmissions. The RF Resource can receive on either of
the duplexor passbands.
loPassband(1) - The RF Resource is receiving on a frequency within
the range identified by cwrDuplexorLoPassbandRange.
hiPassband(2) - The RF Resource is receiving on a frequency within
the range identified by cwrDuplexorHiPassbandRange. |
| STR cwrDuplexorCLEICode | 1.3.6.1.4.1.9.10.52.1.4.1.1.6 | DisplayString | read-write | The CLEI code for this Duplexor. |
| STR cwrDuplexorVendorName | 1.3.6.1.4.1.9.10.52.1.4.1.1.7 | DisplayString | read-write | The Vendor Name for this Duplexor. |
| STR cwrDuplexorSerialNumber | 1.3.6.1.4.1.9.10.52.1.4.1.1.8 | DisplayString | read-write | The Serial number of this Duplexor. |
| cwrRadioExpConformance | 1.3.6.1.4.1.9.10.52.2 | | | |
| cwrRadioExpCompliances | 1.3.6.1.4.1.9.10.52.2.1 | | | |
| cwrRadioExpCompliance | 1.3.6.1.4.1.9.10.52.2.1.1 | | | The compliance statement for Point to Point wireless interface
devices compliant to Cisco Systems Inc. specification. |
| cwrRadioExpGroups | 1.3.6.1.4.1.9.10.52.2.2 | | | |
| cwrComplianceRadioRFGroup | 1.3.6.1.4.1.9.10.52.2.2.1 | | | Group of objects implemented in the point to point wireless
system for managing the Radio Frequency resources on the link. |
| cwrComplianceRadioImageGroup | 1.3.6.1.4.1.9.10.52.2.2.2 | | | Group of objects implemented in the point to point wireless
system for managing images related to the point-to-point wireless
firmware. |
| cwrComplianceRadioLEDGroup | 1.3.6.1.4.1.9.10.52.2.2.3 | | | Group of objects implemented in the point to point wireless
card to provide information about the LEDs on the card. |
| cwrComplianceRadioDuplexorGroup | 1.3.6.1.4.1.9.10.52.2.2.4 | | | Group of objects implemented in the point to point wireless
card to provide information about the duplexor's in the system. |
