All MIBs › CISCO-WAN-FR-PORT-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2002-10-17
Category: Frame Relay, Vendor: Cisco Devices
Description: Manages Cisco WAN Frame Relay port configuration and operational status on MGX service modules.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-WAN-FR-PORT-MIB?
CISCO-WAN-FR-PORT-MIB is a Cisco enterprise MIB for configuring and monitoring Frame Relay ports on WAN service modules within Cisco MGX multiservice switching platforms, covering logical frame relay ports carried over T1/E1 physical lines. It exposes port configuration groups (line number, DS0 channel bitmap, speed, admin type), port state groups reflecting current operational status, and port counter groups for statistics on frame relay traffic. For monitoring, it lets an administrator confirm a frame relay port's administrative and operational state, check configured line speed and DS0 channelization, and pull traffic statistics to spot congestion or errors on the WAN link, which is core to diagnosing service-affecting problems on carrier frame relay circuits. It builds on standard T1/E1 physical-layer MIBs for the underlying line, since a frame relay port is logically layered on a DS0/T1/E1 channel. It is deployed on Cisco MGX WAN switching platforms used by carriers and enterprises to deliver Frame Relay services over T1/E1 access lines, and network engineers can download the CISCO-WAN-FR-PORT-MIB file directly to load it into their MIB browser for these platforms.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-WAN-FR-PORT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco MGX WAN switch (Frame Relay service module)
Monitoring Examples
An operator would poll portAdmin and the corresponding operational state from frPortStateGrp for entries in frPortCnfPortGrpTable to confirm a frame relay port is administratively up and passing traffic, cross-checking portDs0ConfigBitMap and portSpeed to verify the correct DS0 channels and line speed are provisioned. If portRowStatus shows a port as active but frPortCntPortGrp statistics show rising errors, that points to a physical-layer or channelization problem on the underlying T1/E1 line rather than a configuration issue.
What Can Be Monitored
- frame relay port admin/operational state
- DS0 channel configuration
- port line speed
- port type
- frame relay traffic statistics
This MIB depends on
Related MIBs
Imported Objects
From BASIS-MIB
| frPort | OBJECT-IDENTITY |
| frPortCnf | OBJECT-IDENTITY |
| frPortCnt | OBJECT-IDENTITY |
| frPortServiceQueGrp | OBJECT-IDENTITY |
From CISCOWAN-SMI
| ciscoWan | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
How to Use in IPNetwork Monitor
Example using rcvPortFrames OID:
Select a Cisco MGX WAN switch (Frame Relay service module, legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type rcvPortFrames into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of frames Received on the ingress. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in Frames), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoWanFrPortCompliance | 1.3.6.1.4.1.351.150.44.2.2.1 | The compliance statement for objects related to Frame Relay Ports. | ||
| ciscoWanFrPortConfGroup | 1.3.6.1.4.1.351.150.44.2.1.1 | The collection of objects which are used to represent Frame Relay Port information. | ||
| ciscoWanFrPortDs0InDs1Group | 1.3.6.1.4.1.351.150.44.2.1.3 | The objects representing the DS0(in DS1) that are used by the frame relay logical ports. | ||
| ciscoWanFrPortMIB | 1.3.6.1.4.1.351.150.44 | The MIB module to create/configure frame relay ports/interfaces. This module contains tables related to frame relay port states and statistics. The frame relay logical port is referred to as 'frame relay port' in this mib. Terminologies Used: Channel : Generically refers to the user access channel across which frame relay data travels. This is also referred to use logical port/interface in this MIB. Within a given T1 or E1 physical line, a channel can be one of the following, depending on how the line is configured. Unchannelized : The Entire T1/E1 line is considered a channel, where: * The T1 line operates at the speed of 1.536 Mbps and is single channel consisting of 24 T1 time slots. * The E1 line operates at the speed of 1.984 Mbps and is single channel consisting of 31 T1 time slots. Channelized: The channel is any one of the N time slots within a given line, where: * The T1 line consists of any one or more channels. Each channel is any one of 24 time slots. * The E1 line consists of one or more channels. Each channel is any one of 31 time slots. Fractional: The T1/E1 channel is one of the following groupings of consecutively or nonconsecutively assigned time slots: * N T1 time slots(N*56/64Kbps where N=1-23 T1 Time slots per FT1 channel. * N E1 time slots(N*64Kbps where N=1-30 Time slots per E1: channel. SVC : Switched Virtual Circuits. SVCs allow access through a Frame Relay Network by setting up a path to the destination endpoints only when the need arises and tearing down the path when it is no longer needed. Refer ITU Q.933 and Q.922 FECN : Forward Explicit Congestion Notification A bit set by a frame relay network to notify an interface device(DTE) that congestion avoidance procedures should be initiated by the receiving device. BECN : Backward Explicit Congestion Notification A bit set by a frame relay network to notify an interface device(DTE) that congestion avoidance procedures should be initiated by the sending device. DE : Discard Eligibility A user-bit set indicating that a frame may be discarded in preference to other frames if congestion occurs, to maintain the committed quality of service within the network. Frames with the DE bit set are considered Be(Excess Burst Size)excess data. Unchannelized Service Modules: Following Service Modules does not support channelized interfaces(i.e supports only unchannelized). FRSM-VHS : FRSM-2T3/2E3, FRSM-HS2/HS2B, FRSM-T3B/E3B For following service modules, ifTable is supported: FRSM-12. | ||
| ciscoWanFrPortMIBCompliances | 1.3.6.1.4.1.351.150.44.2.2 | |||
| ciscoWanFrPortMIBConformance | 1.3.6.1.4.1.351.150.44.2 | |||
| ciscoWanFrPortMIBGroups | 1.3.6.1.4.1.351.150.44.2.1 | |||
| ciscoWanFrPortServiceQueueGroup | 1.3.6.1.4.1.351.150.44.2.1.6 | The collection of objects related to service queue on frame relay ports. | ||
| ciscoWanFrPortStateGroup | 1.3.6.1.4.1.351.150.44.2.1.4 | The collection of objects related to state information of Frame Relay Ports. | ||
| ciscoWanFrPortStatsGroup | 1.3.6.1.4.1.351.150.44.2.1.5 | The collection of objects related to statistics information of frame relay ports. | ||
| ciscoWanFrPortsUsedGroup | 1.3.6.1.4.1.351.150.44.2.1.7 | The collection of objects related to information on DS0 time slots used in each DS1 line. | ||
| ciscoWanFrPortSvcGroup | 1.3.6.1.4.1.351.150.44.2.1.2 | The collection of objects which are used to represent SVC characteristics of a Frame Relay Port. | ||
| I32 cntPortNum | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.1 | Integer32 | read-only | This is the frame relay(logical) port number. The value of this object must be same as the value of object 'portNum' in frPortCnfPortGrpTable. |
| frPortCnfPortGrp | 1.3.6.1.4.1.351.110.5.1.1.1.1 | |||
| frPortCnfPortGrpEntry | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1 | not-accessible | An entry in the frame relay port table. | |
| frPortCnfPortGrpTable | 1.3.6.1.4.1.351.110.5.1.1.1.1.1 | not-accessible | This table is used for creating/configuring Frame Relay Logical(referred to as frame relay port)Ports. Relation with ifTable: The modules in which ifTable is implemented, the creation of frame relay port in this table will cause an entry to be created in ifTable. The possible interfaces that are created in ifTable are identified by ifType = frameRelayService(44) and frForward(158). The deletion of an entry in this table causes the corresponding entry in ifTable to be deleted. | |
| frPortCntPortGrp | 1.3.6.1.4.1.351.110.5.1.1.2.1 | |||
| frPortCntPortGrpEntry | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1 | not-accessible | An entry for logical port | |
| frPortCntPortGrpTable | 1.3.6.1.4.1.351.110.5.1.1.2.1.1 | not-accessible | The config table is for logical port interface there are upto 248 entries (for 8 E1s) or 192 (for 8 T1s). In FRSM-VHS, there is support for upto 256 entries. | |
| frPortServiceQueGrpEntry | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1 | not-accessible | An entry for logical port. | |
| frPortServiceQueGrpTable | 1.3.6.1.4.1.351.110.5.1.1.1.4.1 | not-accessible | The config table is for logical port interface. In FRSM-VHS, there are 256 entries for FRSM-2CT3 card and 2 entries for FRSM-T3/E3/HS2/T3B/E3B/HS2B-HSSI cards and 8 entries for FRSM-HS2B-12IN1. The table is supported only in FRSM-VHS when the object egrQosFeature in the cardSpecific group is set to egrQosFeatureEnabled. | |
| frPortStateGrp | 1.3.6.1.4.1.351.110.5.1.1.3 | |||
| frPortStateGrpEntry | 1.3.6.1.4.1.351.110.5.1.1.3.1.1 | not-accessible | An entry for logical port. | |
| frPortStateGrpTable | 1.3.6.1.4.1.351.110.5.1.1.3.1 | not-accessible | Table of transmit/receive states of ports. | |
| I32 frPortsUsedLine | 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1.2 | Integer32 | read-only | The value of this object provides the information on DS0 time slots used by the DS1 identified by 'frPortsUsedLineIndex' object. A bit set represents a DS0 that is used by all the logical ports defined so far for DS1 interface. The most significant byte is invalid for DS1. |
| frPortsUsedLineGrpEntry | 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1 | not-accessible | An entry for each DS1 interface. | |
| frPortsUsedLineGrpTable | 1.3.6.1.4.1.351.110.5.1.1.1.1.11 | not-accessible | This table Contains information on the DS0 time slots used in each DS1 interface. | |
| I32 frPortsUsedLineIndex | 1.3.6.1.4.1.351.110.5.1.1.1.1.11.1.1 | Integer32 | read-only | This object uniquely identifies the DS1 interface. |
| I32 frServPortNum | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.1 | Integer32 | read-only | This is the frame relay port number. The value of this object must match with the value of object 'portNum' in frPortCnfPortGrpTable. |
| INT portAdmin | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.9 | INTEGER | read-write | The value of this object is used for changing the desired state of the port. up(1) : Up the port;Admin up down(2) : Down the port;Admin down For Service Modules, supporting ifTable, this is equivalent to 'ifAdminStatus' object. The write-only is not supported in these cases. |
| INT portBERTEnable | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.21 | INTEGER | read-write | The value of this object enables/disables the Bit Error Rate Testing (BERT) on the frame relay port. For FRSM12 card: Not Supported |
| C32 portBytesDiscXceedDEThresh | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.8 | Counter32 | read-only | Counter maintained for the no of bytes discarded due to DE threshold exceeded. |
| C32 portBytesDiscXceedQueFull | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.7 | Counter32 | read-only | Counter maintained for the no of bytes discarded due to port queue depth exceeded. |
| INT portClrButton | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.32 | INTEGER | read-write | The value of this object is used for clearing all the port related statistics counters. clear(2) : Clears the Counters. noaction(1) : No action taken. |
| INT portDeleteSvcs | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.18 | INTEGER | read-write | The value of this object indicates that all the SVC connections on a given frame relay port has to be deleted. For FRSM12 card: Not Supported |
| I32 portDs0ConfigBitMap | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.4 | Integer32 | read-write | This respesents bit map of DS0s for a line/interface which are used to form this logical port. The Bit 0 represents DS0-1(First DS0 timeslot). This object is not applicable for unchannelized service modules. In case of unchannelized interfaces, this field carries the value of 'ffffff'h. |
| INT portDs0Speed | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.5 | INTEGER | read-write | The value of this object is used for configuring the port speed(or data rate) of Ds0 in frame relay port. speed56k(1) : set to 56k speed64k(2) : set to 64k unUsed(3) : Not applicable. This field is not applicable for unchannelized interfaces/ports. In case of unchannelized interfaces this object is set to 'unUsed' always. This object can be specified only during port creation. |
| I32 portEgresDEThresh | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.5 | Integer32 | read-write | DE threshold for the frame relay port. If the total queue depth of all connections mapped to this port queue exceeds this threshold, and the DE bit is set in the incoming frame, then the frame gets dropped. |
| I32 portEgresECNThresh | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.4 | Integer32 | read-write | ECN threshold for the frame relay port. If the total queue depth of all connections mapped to this port queue exceeds this threshold, then the appropriate ECN bit (FECN in the downstream direction and BECN in the upstream direction) get set. |
| I32 portEgresQDepth | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.3 | Integer32 | read-write | Indicates the peak Egress queue depth for the frame relay port. The total queue depth of all connections mapped to this queue should not exceed this value. |
| I32 portEgrPercentUtil | 1.3.6.1.4.1.351.110.5.1.1.3.1.1.6 | Integer32 | read-only | Percentage Utilization of the Port in the Egress direction. |
| I32 portEgrSvcBandW | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.20 | Integer32 | read-only | The value of this object identifies the Egress bandwidth reserved for SVC. For FRSM12 card: Not Supported. |
| INT portEnhancedSIW | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.22 | INTEGER | read-write | This variable enables/disables enhanced SIW feature. Enabling this permits support for SIW translation of Appletalk. This feature is supported only in the FRSM-VHS card. This object is not required in FRSM12 since Appletalk is supported by default in FRF.8.1 and FRSM12 supports FRF.8.1 |
| I32 portEqueueServiceRatio | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.7 | Integer32 | read-write | Number of times queue 1 is serviced for every time queue 2 is serviced. The value 0 is supported only by FRSM-VHS. FRSM-VHS supports two different egress queue servicing algorithms depending on the Egress Qos Feature. if EgrQosFeature is ENABLED, Weighted Fair queueing algorithm will be used to select one queue out of 4 data queues and this object will be set to a default value of 0 in this case and this value cannot be modified by user. In case of EgrQosFeature being DISABLED, this object will be set to a default value of 1 and can be configured to user desired value. This value will be used to decide number of times High priority queue has to be serviced for every time low priority queue is serviced. For FRSM12 card: There is only one scheme of egress scheduling of COS queues within ports, which uses only two COS queues for user data. The scheduling scheme uses a pre-defined ratio to schedule these COS queues on a given port. This object will be used to decide number of times High priority queue has to be serviced for every time low priority queue is serviced. |
| I32 portFileId | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.26 | Integer32 | read-write | The value of this object identifies the Service Class Template(SCT) file ID. The SCT holds the module specific configuration parameters for the frame relay port. This object is not applicable to MGX Release 1.x. |
| I32 portFlagsBetweenFrames | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.6 | Integer32 | read-write | Number of flags transmitted between FR frames For FRSM12 card: Only the values 1 to 8 are supported. The mapping is as follows: MIB object value No. of HDLC flags inserted 1 1 2 2 3 4 4 8 5 16 6 32 7 64 8 128 This object can not be modified if there are any frame relay connections that are configured on the port. |
| INT portFrameChkSumType | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.25 | INTEGER | read-write | The value of this object identifies the CRC Length in the HDLC Packet. Applicable for FrameForwarding ports only. This object can not be modified if there are any frame relay connections that are configured on the port. This object is not applicable to MGX Release 1.x. |
| INT portHeaderLen | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.24 | INTEGER | read-write | The value of this object identifies the Q.922 address field length and DLCI length for this UNI/NNI logical port. This object can not be modified if there are any frame relay connections that are configured on the port. This object is not applicable to MGX Release 1.x. |
| I32 portIngrPercentUtil | 1.3.6.1.4.1.351.110.5.1.1.3.1.1.5 | Integer32 | read-only | Percentage Utilization of the Port in the Ingress direction. |
| I32 portIngrSvcBandW | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.19 | Integer32 | read-only | The value of this object identifies the Ingress bandwidth reserved for SVC. For FRSM12 card: Not Supported |
| I32 portLineNum | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.2 | Integer32 | read-write | This object represents the physical line number on which the frame relay port need to be created. For Service Modules, supporting ifTable, this must be the ifIndex value of the physical line or logical interface. The ifIndex entries in ifTable applicable to this category are identified by ifType values of ds3(30), ds1(18). |
| I32 portM32EgrQueueThresh | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.23 | Integer32 | read-write | This represents the M32 logical port Egress Queue threshold in bytes. Frames will not be queued until the number of bytes in the queue is less than the threshold. The default value is 6000. Using a very low value could under utilize the logical port. This is supported in FRSM 8t1e1 and FRSM 4t1e1 Service Modules only. |
| I32 portNextAvailable | 1.3.6.1.4.1.351.110.5.1.1.1.1.6 | Integer32 | read-only | This variable contains the next UNUSED logical port number. This number can be used in channel config table, the portNextAvailable gets updated if the number gets used to create a logical port. A '0' indicates that no more ports are available. For FRSM12 Card: Not Supported |
| I32 portNum | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.1 | Integer32 | read-only | This is the frame relay(logical) port number. For Service Modules, supporting ifTable, this must be the ifIndex value of the frame relay port. The port number value supported depends upon the following for each Service Module: - type(Channelized, Unchannelized, Fractional etc) of physical line and number of physical lines - Number of physical line supported - Limitations due to Service Module Hardware components. Port Number mapping is as follows: (NOTE: All the Supported Service Module information is not provided here). T1(channelized) : 24 Time Slots * Max #Lines Supported. Example: 8 Port Service Module - 1..192(24*8) E1(channelized) : 31 Time Slots * Max #Lines Supported. Example: 8 Port Service Module - 1..248(31*8) T3 Channelized : Example: 2CT3 Service Module: 1-256(Limited by hardware) Unchannelized VHS : Range is 1-2 (T3/E3/HS2/T3B/E3B/HS2B-HSSI) FRSM-HS2B-12IN1 : Range is 1-8 FRSM-12 : same as ifIndex value. With the above convention, Port Number mapping is as follows: T1 Service Module : Range is 1-192. E1 Service Module : Range is 1-248. 2CT3 Service Module : Range is 1-256 NOTE: For other Service Modules(Where ifTable is supported): This value for this object must be same as the ifIndex value for the frame relay port ifTable. The frame relay ports identified by ifType values frameRelayService(44) and frForward(158) are valid for this object. Since, Frame Relay Port table is used for creating entries in ifTable, it sounds odd to specify ifIndex value for this object, even before creating the ifTable entries!. The reason(s) for this is as follows: - There are tables in other frame relay mibs, which are indexed by auxiliary objects(objects which are both specified in the INDEX clause and columnar objects of the same row) whose value is supposed to be same as 'portNum'. These MIBs have been used earlier by NMS Applications for the other product lines(MGX8250, MGX8220 etc). - The same frame relay tables in used in other products has been decided to use in new products(for example MGX8850 with FRSM-12 Service Module). It is a requirement that ifTable must be supported in New Service Modules. If we use ifIndex value of the frame relay port (after creation) in other tables(FR Port Stats, FR R Resource Partition or FR Connection etc), and if ifIndex value is different than 'portNum', then it will break the NMS applications which have been using this MIB with the assumptions that 'portNum' and INDEXes(For example: frResPartPortNum, lmiCnfPortNum, etc) are same. To avoid this confusion, it is required that 'portNum' value must be same as 'ifIndex' of the frame relay port. |
| INT portOverSubEnable | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.27 | INTEGER | read-write | The value of this object enables/disables the port to be over subscribed. This object is not applicable to MGX Release 1.x. |
| INT portOversubscribed | 1.3.6.1.4.1.351.110.5.1.1.3.1.1.4 | INTEGER | read-only | This variable indicates the whether the port is over subscribed or not. |
| I32 portQBwInc | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.6 | Integer32 | read-only | Denotes the bandwidth increment for this port queue. The bandwidth increment is the percentage of the port bandwidth used by all connections mapped to a particular queue scaled by the value 16384. |
| INT portRowStatus | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.3 | INTEGER | read-write | The value of this object is used for creating modifying or deleting frame relay ports. The possible values are : add(1) : Create frame relay port del(2) : Delete frame relay port mod(3) : Modify the frame relay port. This value is required to be set in Some Older Service Modules (FRSM-8T1/E1, FRSM-VHS, FRSM-HS2B etc) to modify the port parameters. In some service modules, when the port is successfully created(add(1)), this object is set internally to mod(3). The reason for this is, one can modify parameters of the port without requiring to go through an explicit mod(3) to modify the parameters. |
| INT portServiceQueueNo | 1.3.6.1.4.1.351.110.5.1.1.1.4.1.1.2 | INTEGER | read-write | This identifies the Q depending on the Service Type 1 High Priority Queue 2 rt VBR Queue 3 nrt VBR and ABR Queue 4 UBR Queue queue5(5) to queue8(8) are reserved for future use There are 8 queues but only four are being used as of now. |
| I32 portSignallingState | 1.3.6.1.4.1.351.110.5.1.1.3.1.1.3 | Integer32 | read-only | Bit 0 = 0 -> LMI O.K. or not enabled Bit 0 = 1 -> LMI failed Bit 1 = 0 -> CLLM O.K. or not enabled Bit 1 = 1 -> CLLM failed |
| I32 portSpeed | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.8 | Integer32 | read-only | The value of this object contains the Configured speed of port. |
| INT portState | 1.3.6.1.4.1.351.110.5.1.1.3.1.1.2 | INTEGER | read-only | This variable indicates the state of the logical port |
| I32 portsUsedLine1 | 1.3.6.1.4.1.351.110.5.1.1.1.1.2 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1. This is for line. |
| I32 portsUsedLine2 | 1.3.6.1.4.1.351.110.5.1.1.1.1.3 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1. This is for line 2. |
| I32 portsUsedLine3 | 1.3.6.1.4.1.351.110.5.1.1.1.1.4 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 3. |
| I32 portsUsedLine4 | 1.3.6.1.4.1.351.110.5.1.1.1.1.5 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 4. |
| I32 portsUsedLine5 | 1.3.6.1.4.1.351.110.5.1.1.1.1.7 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 5. |
| I32 portsUsedLine6 | 1.3.6.1.4.1.351.110.5.1.1.1.1.8 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 6. |
| I32 portsUsedLine7 | 1.3.6.1.4.1.351.110.5.1.1.1.1.9 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 7. |
| I32 portsUsedLine8 | 1.3.6.1.4.1.351.110.5.1.1.1.1.10 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 8. |
| I32 portSvcDlciHigh | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.17 | Integer32 | read-only | The value of this object identifies the high end of reserved DLCI for SVC. For FRSM12 card: Not Supported. |
| I32 portSvcDlciLow | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.16 | Integer32 | read-only | The value of this object identifies the low end of reserved DLCI for SVC. For FRSM12 card: Not Supported. |
| INT portSvcInUse | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.12 | INTEGER | read-write | The value of this object is used for representing whether SVC is in use or not. For FRSM12 card: Not Supported |
| I32 portSvcLcnHigh | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.15 | Integer32 | read-only | The value of this object identifies the high end of reserved LCN for SVC. For FRSM12 card: Not Supported |
| I32 portSvcLcnLow | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.14 | Integer32 | read-only | The value of this object identifies the low end of the reserved LCN for SVC. For FRSM12 card: Not Supported |
| INT portSvcShareLcn | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.13 | INTEGER | read-only | The value of this object identifies the SVC shared LCN type. For FRSM12 card: Not Supported |
| INT portSvcStatus | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.11 | INTEGER | read-write | The value of this object is used for enabling/disabling the SVC operation on a frame relay port. For FRSM12 card: Not Supported |
| INT portType | 1.3.6.1.4.1.351.110.5.1.1.1.1.1.1.10 | INTEGER | read-write | The value of this object identifies the network interface for this frame relay port. The Possible values are: frame-relay(1) : Frame Relay Service Port frFUNI (2) : Frame based UNI Port. when a frame arrives from the FUNI interface the 2 byte FUNI header is removed and frame is segmented into ATM Cells by using AAL5. frame-forward(3): Frame Forward Port. In this case 2 byte Q.922 header is not assumed or interpreted. The signaling(LMI) parameters are not applicable for these ports. Relationship with ifTable: The service modules in which ifTable is implemented following side-effects will take place. For value frame-relay(1) an ifTable entry with ifType = frameRelayService(44) will be created. For value frame-forward(3) an ifTable entry with ifType = frForward(158) will be created. This object can not be modified after the port is created. |
| C32 rcvBufNotAvailable | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.19 | Counter32 | read-only | The number of times the receiver is turned off |
| C32 rcvFramesAbort | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.11 | Counter32 | read-only | The number of received frames aborted |
| C32 rcvFramesDiscAlignmentError | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.8 | Counter32 | read-only | The number of frames discarded on the ingress due to Alignment error. |
| C32 rcvFramesDiscCRCError | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.7 | Counter32 | read-only | The number of frames discarded on the ingress due to CRC error. |
| C32 rcvFramesDiscIllegalHeader | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.10 | Counter32 | read-only | The number of frames discarded on the ingress due to illegal header. |
| C32 rcvFramesDiscIllegalLen | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.9 | Counter32 | read-only | The number of frames discarded on the ingress due to illegal length. |
| C32 rcvFramesDiscNoChan | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.33 | Counter32 | read-only | The number of frames received when no channel is setup. |
| C32 rcvFramesDiscOverrun | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.34 | Counter32 | read-only | The number of frames discarded in Ingress direction due to FIFO overrun in HDLC Controller. This object is not applicable to MGX Release 1.x |
| C32 rcvFramesUnknownDLCI | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.12 | Counter32 | read-only | The number of frames received with an unknown DLCI. |
| I32 rcvLastUnknownDLCI | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.13 | Integer32 | read-only | The last unknown DLCI received. |
| C32 rcvPortBytes | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.3 | Counter32 | read-only | The number of bytes Received on the ingress. |
| C32 rcvPortBytesDE | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.38 | Counter32 | read-only | Number of bytes received in the ingress direction by the port with DE bit set to 1 |
| C32 rcvPortBytesDiscXceedDEThresh | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.41 | Counter32 | read-only | Number of bytes discarded in the ingress direction by the port due to exceeded DE Threshold |
| C32 rcvPortFramesEx | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.2 | Counter32 | read-only | The number of frames Received on the ingress. |
| C32 rcvPortFramesBECN | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.6 | Counter32 | read-only | The number of frames with BECN bit set received on the ingress. |
| C32 rcvPortFramesDE | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.4 | Counter32 | read-only | The number of frames with DE bit set received on the ingress. |
| C32 rcvPortFramesDiscard | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.35 | Counter32 | read-only | Number of framesdiscarded in the ingress direction by the port |
| C32 rcvPortFramesDiscXceedDEThresh | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.17 | Counter32 | read-only | The number of frames discarded on the ingress due to exceeded DE Threshold. |
| C32 rcvPortFramesFECN | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.5 | Counter32 | read-only | The number of frames with FECN bit set received on the ingress. |
| C32 rcvPortFramesTaggedBECN | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.15 | Counter32 | read-only | The number of frames received that were tagged with BECN bit. |
| C32 rcvPortFramesTaggedDE | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.16 | Counter32 | read-only | The number of frames received that were tagged with DE bit. |
| C32 rcvPortFramesTaggedFECN | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.14 | Counter32 | read-only | The number of frames received that were tagged with FECN bit. |
| I32 rcvPortKbpsAIR | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.18 | Integer32 | read-only | Received Average Information Rate in KBPS. |
| I32 statePortNum | 1.3.6.1.4.1.351.110.5.1.1.3.1.1.1 | Integer32 | read-only | This is the frame relay(logical) port number. The value of this object must match with the value of object 'portNum' in frPortCnfPortGrpTable. |
| C32 xmtBufNotAvailable | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.31 | Counter32 | read-only | The number of times the transmitter is turned off For FRSM12 Card: Not Supported |
| C32 xmtFramesAbort | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.28 | Counter32 | read-only | The number of transmit frames aborted For FRSM12 Card: Not Supported |
| C32 xmtFramesUnderrun | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.29 | Counter32 | read-only | The number of frames discarded due to underrun. |
| C32 xmtPortBytes | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.21 | Counter32 | read-only | The number of bytes transmitted. |
| C32 xmtPortBytesDE | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.37 | Counter32 | read-only | Number of bytes transmitted in the egress direction by the port with DE bit set to 1 |
| C32 xmtPortBytesDiscXceedDEThresh | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.40 | Counter32 | read-only | Number of bytes discarded in the egress direction by the port due to exceeded DE Threshold |
| C32 xmtPortBytesDiscXceedQDepth | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.25 | Counter32 | read-only | The number of bytes discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported |
| C32 xmtPortBytesDuringLMIAlarm | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.27 | Counter32 | read-only | The number of bytes transmitted during LMI logical port alarm |
| C32 xmtPortFrames | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.20 | Counter32 | read-only | The number of frames transmitted. |
| C32 xmtPortFramesBECN | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.23 | Counter32 | read-only | The number of frames transmitted with BECN bit already set. |
| C32 xmtPortFramesDE | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.36 | Counter32 | read-only | Number of frames transmitted in the egress direction by the port with DE bit set to 1 |
| C32 xmtPortFramesDiscXceedDEThresh | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.39 | Counter32 | read-only | Number of frames discarded in the egress direction by the port due to exceeded DE Threshold |
| C32 xmtPortFramesDiscXceedQDepth | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.24 | Counter32 | read-only | The number of frames discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported |
| C32 xmtPortFramesDuringLMIAlarm | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.26 | Counter32 | read-only | The number of frames transmitted during LMI logical port alarm |
| C32 xmtPortFramesFECN | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.22 | Counter32 | read-only | The number of frames transmitted with FECN bit already set. |
| I32 xmtPortKbpsAIR | 1.3.6.1.4.1.351.110.5.1.1.2.1.1.1.30 | Integer32 | read-only | Transmit Average Information Rate in KBPS. |
RFC description
Manages Frame Relay port configuration and statistics on Cisco WAN devices.
Start monitoring Cisco MGX WAN switch (Frame Relay service module, legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.