| OID symbolic | OID numeric | Type | Access | Description |
|---|
| I32 bbChanClpHiThreshold | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.22 | Integer32 | read-write | Ingress CLP High Threshold.
Default is 3/4 of max cell count. |
| I32 bbChanClpLoThreshold | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.23 | Integer32 | read-write | Ingress CLP Low Threshold. Valid only when
Ingress CLP Hysteresis option is selected.
Default Value is 1/2 of max cell count. |
| bbChanCnfGrpEntry | 1.3.6.1.4.1.351.110.5.2.7.1.1.1 | | not-accessible | The config table is for logical channel. |
| bbChanCnfGrpTable | 1.3.6.1.4.1.351.110.5.2.7.1.1 | | not-accessible | The Broadband Channel config table is for a channel on logical
interface. There will an entry for each of the channel added on the
logical partition of the physical line.
Following parameters are needed if the connection is from a
PXM user port and policing is enabled. These apply to
connection on PXM lines confiured as user port only.
PCR/CDVT is used for GCRA1 and
SCR/MBS is used for GCRA2
UpcEnable
UpcPCR
UpcCDVT
UpcSCRPolicing
for CBR conns.
UpcPCR0
UpcCDVT0
for non CBR conns.
UpcSCR
UpcMBS |
| I32 bbChanCnfNum | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.1 | Integer32 | read-only | This identifies a channel on the PXM logical interface, used as
PXM port. |
| INT bbChanCongstUpdateCode | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.24 | INTEGER | read-write | Ingress Channel Congestion Update Code. |
| STR bbChanConnDesc | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.5 | DisplayString | read-write | A string that has been defined to give a
descriptive name to the connection. |
| INT bbChanConnType | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.3 | INTEGER | read-write | This specifies the connection type
vpc(1) : Virtual Path Connection
vcc(2) : Virtual Channel Connection
This object can not be modified once the connection is created. |
| INT bbChanDiscardOption | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.20 | INTEGER | read-write | Enable Frame Discard or CLP Hysteresis. |
| I32 bbChanEfciThreshold | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.19 | Integer32 | read-write | Threshold above which EFCI bit is to be set.
Default Value is 3/4 of max cell count. |
| I32 bbChanEgrPercentUtil | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.27 | Integer32 | read-write | Percentage Utilization of the EgrService Rate.
This is used for egress bandwidth calculation and
connection admission control. |
| I32 bbChanEgrSrvRate | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.28 | Integer32 | read-write | Egress service rate - This is used for egress bandwidth calculation
and for connection admission control. The actual value
depends on the speed of the logical interface. |
| INT bbChanEgrXmtState | 1.3.6.1.4.1.351.110.5.2.7.2.1.1.3 | INTEGER | read-only | Indicates the status of port transmit(Egress). |
| I32 bbChanFrmDiscardThreshold | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.21 | Integer32 | read-write | Ingress Frame Discard Threshold.
Valid only when Ingress Frame Discard option is selected. |
| INT bbChanGcra1Action | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.16 | INTEGER | read-write | GCRA1 Action.
1 = No Action
2 = Tag Untagged cells
3 = Tag untagged cells and discard tagged cells
4 = Discard all (0+1) non-comforming cells. |
| INT bbChanGcra2Action | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.17 | INTEGER | read-write | GCRA2 Action.
1 = No Action
2 = Tag Untagged cells
3 = Tag untagged cells and discard tagged cells
4 = Discard all (0+1) non-comforming cells. |
| I32 bbChanIfNum | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.8 | Integer32 | read-write | Channel's logical Interface from which traffic of the connection
will be received. |
| I32 bbChanIngrPercentUtil | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.26 | Integer32 | read-write | Percentage Utilization of the IngrService Rate. This is used
for connection admission control. |
| INT bbChanIngrRcvState | 1.3.6.1.4.1.351.110.5.2.7.2.1.1.4 | INTEGER | read-only | indicates the status of port receive(Ingress). |
| ADR bbChanLocalNsapAddr | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.32 | IfNsapAddress | read-write | The Near End NSAP Address value for this channel. |
| I32 bbChanLocalVci | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.31 | Integer32 | read-only | The VCI value for this channel. |
| I32 bbChanLocalVpi | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.30 | Integer32 | read-only | The VPI value for this channel. |
| INT bbChanMaster | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.36 | INTEGER | read-write | This is used by the PXM switch platform module,
to determine if this endpoint ia master or slave. |
| I32 bbChanMaxCellMemThreshold | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.25 | Integer32 | read-write | Maximum number of cells of that connection in
the memory.
Assuming Total Cell Memory is 512K cells, this is defaulted to
half of total size. |
| I32 bbChanMaxCost | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.38 | Integer32 | read-write | Maximum allowed cost. It is related to Cost Based Routing.
This is used by PXM so that it won't choose a path with a
cost greater than this configured level. |
| I32 bbChanNumNextAvailable | 1.3.6.1.4.1.351.110.5.2.7.1.2 | Integer32 | read-only | This variable contains the next unused channel number of the possible
4096 . This number can be used in channel config table.
ChanNumNextAvailable gets updated whenever this number is used to
create a new logical channel. Value 0 for this variable indicates that
no more channels are available. |
| INT bbChanOvrSubOvrRide | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.29 | INTEGER | read-write | Channel Over Subscrive Override
This MIB variable allows one to add a new connection on a port
even if it is over subscribed. |
| ADR bbChanRemoteNsapAddr | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.35 | IfNsapAddress | read-write | The Far End NSAP Address value for this channel. |
| I32 bbChanRemoteVci | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.34 | Integer32 | read-write | The VCI value for this channel. |
| I32 bbChanRemoteVpi | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.33 | Integer32 | read-write | The VPI value for this channel. |
| INT bbChanRestrictTrkType | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.39 | INTEGER | read-write | Restricted trunk type for routind, used by PXM.
It specifies that the connection either cannot be
routed over satellite trunks or terrestrial trunks,
or it can be on any type of trunk. |
| INT bbChanRowStatus | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.2 | INTEGER | read-write | This object is used for adding/deleting/modifying
entries in the table.
add(1) : Adds the entry.
delete(2) : Deletes the entry
modify(3) : Set this before modifying any entries in the table.
Following parameters need to be available before creating
the entry:
bbChanConnType,
bbChanServiceType. |
| I32 bbChanRtePriority | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.37 | Integer32 | read-write | This is also known as class of service, it is used by
PXM to determine how important this connection is when
selecting connections to route. |
| INT bbChanServiceType | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.4 | INTEGER | read-write | This specifies the service type
cbr(1) : Constant Bit Rate
vbr(2) : Variable Bit Rate
abr(3) : Available Bit Rate
ubr(4) : Unspecified Bit Rate
vbr-rt(5): Variable Bit Rate - Real Time
This object can not be modified once the connection is created. |
| INT bbChanState | 1.3.6.1.4.1.351.110.5.2.7.2.1.1.2 | INTEGER | read-only | This variable indicates the state of the VC (channel). |
| bbChanStateGrpEntry | 1.3.6.1.4.1.351.110.5.2.7.2.1.1 | | not-accessible | The state table is for logical channel.
The available number of channels on the broadband interface (user ports)
on the PXM card is restricted to 4K.
The PXM card has 2 Queue Engines ( QE0 and QE1).
Current calculations allow 31954 GLCNs on QE0, and 31748 GLCNs on QE1. |
| bbChanStateGrpTable | 1.3.6.1.4.1.351.110.5.2.7.2.1 | | not-accessible | The Broadband Channel state table is for a channel on logical
interface. There will an entry for each of the channel added on the
logical partition of the physical line. |
| I32 bbChanStateNum | 1.3.6.1.4.1.351.110.5.2.7.2.1.1.1 | Integer32 | read-only | Refers to the logical channel number. |
| I32 bbChanSvcConnId | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.7 | Integer32 | read-write | This connection ID is for future use Currently not supported. |
| INT bbChanSvcFlag | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.6 | INTEGER | read-write | This specifies the connection type
svc(1) : SVC connection
pvc(2) : PVC connection, used by PAR(Portable Auto Route)
spvc(3) : Soft PVC connection, used by PNNI |
| I32 bbChanTestResult | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.42 | Integer32 | read-only | This is round trip delay in milliseconds.
When you select testdelay option for the chanTestType,
the result of the test that is measured in milliseconds
can be read in chanTestResult. |
| INT bbChanTestState | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.41 | INTEGER | read-only | This object provides the state of the test performed
on a connection.
When you add a connection then the chanTestState becomes notinprogress
and when you select any test, it would go to inprogress state and after
it completes the test, it will go to failed or passed state.
1 = Passed
2 = Failed
3 = In Progress
4 = Not In Progress |
| INT bbChanTestStateCPESide | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.44 | INTEGER | read-only | This shows the state of the test
When you add a connection then the chanTestState becomes notinprogress
and when you select any test, it would go to inprogress state and after
it completes the test, it will go to failed or passed state.
1 = Passed
2 = Failed
3 = In Progress
4 = Not In Progress |
| INT bbChanTestType | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.40 | INTEGER | read-write | The chanTestType starts testing the continuity or delay
of a connection. It sends specific cell patterns toward
the network and the terminating end of this connection
has to be an AXIS or ASI of a BPX in order for this test
to be working. The receiving node would loop back when
it receives these cells. The test should be done in
about couple of seconds.
testcon(1) : The testcon tests the continuity of
the connection and testdelay uses the same
test except that it measures for delay through
the network.
To test the delay follow this procedure:
a- set chanTestType to testdelay
b- read chanTestState till it is Pass or Fail
c- Read chanTestResult for the delay if it is Pass
* Note that the chanTestType would go back to notest when the
test is completed
To test the continuity follow this procedure:
a- set chanTestType to testcon
b- read chanTestState till it is Pass or Fail
* Note that the chanTestType would go back to notest when the
test is completed
You CAN NOT select 2 tests back to back, you have to select one
and wait for the result and then start the other one. |
| INT bbChanTestTypeCPESide | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.43 | INTEGER | read-write | The chanTestType starts testing the segment continuity
of a connection.
It sends OAM Segment loopback cell towards port side (CPE)
The CPE would loop back the cell
To test the continuity follow this procedure:
a- set chanTestTypeCPEside to testconseg
b- read chanTestState till it is Pass or Fail
*Note that the chanTestType would go back to notest when the
test is completed. |
| I32 bbChanUpcCDVT | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.13 | Integer32 | read-write | Compliant Cell Delay Variation. Also known as
CDVT(0+1), Cell Delay Variation Tolerance, which
specifies the maximum time period for accumulated
violations of cell-arrival time parameters. This object
applies to the First Leaky bucket for cells with Cell
Loss Priority of 0 or 1.
. Units: microseconds.
. Applicable connection types:
UBR, CBR, VBR, ABR
. Default:
CBR: 10000
Others: 250000 |
| INT bbChanUpcEnable | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.11 | INTEGER | read-write | enables/disables UPC for Ingress cells. |
| I32 bbChanUpcMBS | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.15 | Integer32 | read-write | Maximum Burst Size (MBS). Also known as Compliant Burst Size (CBS).
. Units: cells
. Applicable connection types:
. VBR, ABR
. Default: 1000
. Range : 1-5000000 |
| I32 bbChanUpcMCR | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.53 | Integer32 | read-write | SCR, Sustainable Cell Rate, is an upper bound on the
conforming average rate of an ATM connection, over
time scales which are long relative to those for which
the PCR is defined. Enforcement of this bound by the UPC
could allow the network to allocate sufficient resources,
but less than thos based on the PCR, and still ensure
that the performance objectives (e.g., Cell Loss Ratio)
can be achieved.
. Units: cell per second.
. Applicable connection types:
. ABR
. Ranges:
T3 : 50-96000
E3 : 50-80000
OC3 : 50-353208
OC12: 50-1412832
. Default: 50 |
| I32 bbChanUpcPCR | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.12 | Integer32 | read-write | PCR(0+1), Peak Cell Rate, specifies an upper bound on
rate at which traffic can be submitted on an ATM
connection. This object applies to the First Leaky
Bucket for leaving cells with Cell Loss Priority of 0 or 1.
. Units: cells per second.
. Applicable connection types:
UBR, CBR, VBR, ABR
. Default: 50
. Ranges:
T3 : 50-96000
E3 : 50-80000
OC3 : 50-353208
OC12: 50-1412832
PCR is used for GCRA1. |
| I32 bbChanUpcSCR | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.14 | Integer32 | read-write | SCR, Sustainable Cell Rate, is an upper bound on the
conforming average rate of an ATM connection, over
time scales which are long relative to those for which
the PCR is defined. Enforcement of this bound by the UPC
could allow the network to allocate sufficient resources,
but less than thos based on the PCR, and still ensure
that the performance objectives (e.g., Cell Loss Ratio)
can be achieved.
. Units: cell per second.
. Applicable connection types:
. VBR, ABR
. Ranges:
T3 : 50-96000
E3 : 50-80000
OC3 : 50-353208
OC12: 50-1412832
. Default: 50 |
| INT bbChanUpcSCRPolicing | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.18 | INTEGER | read-write | Selects SCR policing for CLP = 0 or all cells. |
| I32 bbChanVci | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.10 | Integer32 | read-write | VCI for the connection. |
| I32 bbChanVpi | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.9 | Integer32 | read-write | VPI for the connection. |
| I32 bbChanVpIdNextAvailable | 1.3.6.1.4.1.351.110.5.2.7.1.3 | Integer32 | read-only | This in only valid for a Service Module, will NOT be used in PXM.
This variable contains the next unused local VPId of the possible
1 to 4095. This number can be used in channel config table. It gets
updated if the number is used to create a new vp connection.
The max. no. of VP conn.s is limited to the VPI range configured
for this logical interface.
Value of 0 for this variable indicates that no more vp connections
are available |
| I32 bbConnPCR | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.47 | Integer32 | read-write | Peak cell rate, could be derived from the end point parameter |
| I32 bbConnPercentUtil | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.49 | Integer32 | read-write | This is the expected long-term utilization of the
channel by this end-point. |
| I32 bbConnSCR | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.48 | Integer32 | read-write | Sustained cell rate, could be derived from the end point parameter |
| INT bbConnServiceType | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.46 | INTEGER | read-write | This specifies the service type
1 ==> Constant Bit Rate
2 ==> Variable Bit Rate
4 ==> Unspecified Bit Rate
6 ==> Available Bit Rate ( standard )
8 ==> Variable Bit Rate - Real-Time
Note that this is used by PXM card,
Also to make it compatible with existing AUSM MIB definition,
value 3 is not used.
foresight ABR is not supported in PXM , i.e Virtual Service Module |
| INT bbConnVpcFlag | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.45 | INTEGER | read-write | This represents the connection type, used for PXM to
identify VPC/VCC. |
| I32 bbRemoteConnPCR | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.50 | Integer32 | read-write | Peak cell rate of the other end, if not set, will be
set to the same as local end PCR (bbChanUpcPCR). However,
note that if the PCRs for both local and remote end
are set to the different value (i.e., asymmetric conn),
then this should be set differently from local end PCR. |
| I32 bbRemoteConnPercentUtil | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.52 | Integer32 | read-write | This is the expected long-term utilization of the
channel by this end-point. If this is not specified in
the connection setup request, it'll be defaulted to
100 percent |
| I32 bbRemoteConnSCR | 1.3.6.1.4.1.351.110.5.2.7.1.1.1.51 | Integer32 | read-write | Sustained cell rate of the other end, if not set, will be
set to the same as local end SCR (bbChanUpcSCR). However,
note that if the PCRs for both local and remote end
are set to the different value (i.e., asymmetric conn),
then this should be set differently from local end SCR. |
| ciscoWanBbifAtmConnMIB | 1.3.6.1.4.1.351.150.35 | | | The MIB module to configure the ATM Connections
on a broad band interface in PXM1 Service module. |
| cwbAtmConnCompliance | 1.3.6.1.4.1.351.150.35.2.2.1 | | | The compliance statement for SNMP entities
which support Frame realy connection MIB. |
| cwbAtmConnGeneralGroup | 1.3.6.1.4.1.351.150.35.2.1.3 | | | A collection of objects related to next
available channeli number and next available
VPI value of connections supported. |
| cwbAtmConnGroup | 1.3.6.1.4.1.351.150.35.2.1.1 | | | A collection of objects providing information
applicable to an ATM Connection on broad band interfaces. |
| cwbAtmConnMIBCompliances | 1.3.6.1.4.1.351.150.35.2.2 | | | |
| cwbAtmConnMIBConformance | 1.3.6.1.4.1.351.150.35.2 | | | |
| cwbAtmConnMIBGroups | 1.3.6.1.4.1.351.150.35.2.1 | | | |
| cwbAtmConnStateGroup | 1.3.6.1.4.1.351.150.35.2.1.2 | | | A collection of objects related to state
of ATM Connections on Broad band interface. |
