CISCO-LWAPP-HA-MIB

All MIBs › CISCO-LWAPP-HA-MIB

Organization: Cisco Systems Inc.

Last Updated: 2020-06-07

Category: Cisco Devices, Hardware and Environment, Wireless and WLAN

Description: Manages LWAPP/CAPWAP wireless LAN controller high availability, SSO, and redundancy state.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-LWAPP-HA-MIB?

The CISCO-LWAPP-HA-MIB manages and reports high-availability, Stateful Switchover, and redundancy status for Cisco Wireless LAN Controllers that terminate LWAPP/CAPWAP tunnels from lightweight access points. It exposes objects describing the HA peer's IP/MAC addressing, redundancy interface addressing, virtual MAC address, and which unit is currently primary. Administrators rely on it to monitor the hardware/software redundancy health of a WLC pair, confirming cLHaPrimaryUnit reflects the expected active controller and that peer IP/MAC addresses are correctly reachable, since a mismatch or unreachable peer signals an HA link failure or unexpected failover. It is part of the Cisco LWAPP/CAPWAP wireless controller MIB family, built on standard IP addressing conventions such as InetAddressType/InetAddress for its peer objects. It is deployed in enterprise WLAN designs using paired Cisco WLCs configured for SSO/HA to ensure continuous wireless service during a controller failure. Engineers can download the CISCO-LWAPP-HA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-LWAPP-HA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco Wireless LAN Controller (WLC) pair configured for HA/SSO

Monitoring Examples

An admin polls cLHaPrimaryUnit to confirm which controller in an HA pair is currently active, and checks cLHaPeerIpAddress/cLHaPeerMacAddress against expected values to verify the HA link to the standby unit is intact. cLHaVirtualMacAddress and cLHaRedundancyIpAddress reveal the shared identity used during failover, so an unexpected change in cLHaPrimaryUnit combined with peer address unreachability would indicate an HA failover event or split-brain condition.

What Can Be Monitored

current primary/active HA unit
HA peer IP and MAC address reachability
virtual MAC address
redundancy interface IP address
AP SSO configuration state

Imported Objects

From CISCO-RF-MIB

cRFStatusPeerUnitState	OBJECT-TYPE
cRFStatusUnitState	OBJECT-TYPE

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From RFC1213-MIB

sysName

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using cLHaSecondaryControllerUsageDayCounter OID:

Select a Cisco Wireless LAN Controller (WLC) pair configured for HA/SSO as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cLHaSecondaryControllerUsageDayCounter into the Find box to locate it in the OID tree, then select it and click OK. This object represents the number of days the secondary controller is used. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ciscoLwappHaMIB	1.3.6.1.4.1.9.9.843			This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB is used to show and configure High availability (HA) related statistics. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node, Mobile Station(Ms) and client are used interchangeably. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
ciscoLwappHaMIBNotifs	1.3.6.1.4.1.9.9.843.0
NTF cLHaSecondaryControllerUsageTrap	1.3.6.1.4.1.9.9.843.0.1			This notification is sent on the event of a generic failure between the active and peer unit.
NTF cLHaRFSwapInfoTrap	1.3.6.1.4.1.9.9.843.0.2			The notification is sent by the active redundant unit whenever its RF state changes or the RF state of the peer unit changes. To avoid a flurry of notifications for all state transitions, notifications will only be sent for transitions to the following RF states: disabled (for the peer state) standbyCold standbyHot active activeExtraload.
NTF cLHaBulkSyncCompleteTrap	1.3.6.1.4.1.9.9.843.0.3			The notification is sent by the active redundant unit whenever the BulkSync to peer is complete.
NTF cLHaPeerHotStandbyTrap	1.3.6.1.4.1.9.9.843.0.4			The notification is sent by the active redundant unit whenever its peer unit turned hot-standby.
ciscoLwappHaMIBObjects	1.3.6.1.4.1.9.9.843.1
ciscoLwappHaGlobalConfig	1.3.6.1.4.1.9.9.843.1.1
T/F cLHaApSsoConfig	1.3.6.1.4.1.9.9.843.1.1.1	TruthValue	read-write	This object specifies the value of redundancy mode statefull switch over (SSO). A value of 'true' indicates that, redundancy mode SSO is enabled. A value of 'false' indicates that, redundancy mode SSO is disabled.
IPt cLHaPeerIpAddressType	1.3.6.1.4.1.9.9.843.1.1.2	InetAddressType	read-write	This object specifies the peer WLC IP address type.
IP cLHaPeerIpAddress	1.3.6.1.4.1.9.9.843.1.1.3	InetAddress	read-write	This object specifies the peer WLC IP address.
IPt cLHaServicePortPeerIpAddressType	1.3.6.1.4.1.9.9.843.1.1.4	InetAddressType	read-write	This object specifies the peer WLC service port IP address type.
IP cLHaServicePortPeerIpAddress	1.3.6.1.4.1.9.9.843.1.1.5	InetAddress	read-write	This object specifies the peer WLC service port IP address.
IPt cLHaServicePortPeerIpNetMaskType	1.3.6.1.4.1.9.9.843.1.1.6	InetAddressType	read-write	This object specifies the peer WLC service port net mask IP type.
IP cLHaServicePortPeerIpNetMask	1.3.6.1.4.1.9.9.843.1.1.7	InetAddress	read-write	This object specifies the peer WLC service port net mask IP address.
IPt cLHaRedundancyIpAddressType	1.3.6.1.4.1.9.9.843.1.1.8	InetAddressType	read-only	This object represents the peer WLC redundancy management interface IP address type.
IP cLHaRedundancyIpAddress	1.3.6.1.4.1.9.9.843.1.1.9	InetAddress	read-only	This object represents the peer WLC redundancy management interface IP address.
MAC cLHaPeerMacAddress	1.3.6.1.4.1.9.9.843.1.1.10	MacAddress	read-only	This object represents the peer WLC mac address.
MAC cLHaVirtualMacAddress	1.3.6.1.4.1.9.9.843.1.1.11	MacAddress	read-write	This object specifies the peer WLC mobility MAC address.
T/F cLHaPrimaryUnit	1.3.6.1.4.1.9.9.843.1.1.12	TruthValue	read-write	This object specifies whether this is the primary or secondary unit. A value of 'true' indicates that, this unit is the primary unit. A value of 'false' indicates that, this unit is the secondary unit.
T/F cLHaLinkEncryption	1.3.6.1.4.1.9.9.843.1.1.13	TruthValue	read-write	This object specifies whether link encryption is enabled or disabled. A value of 'true' indicates that, link encryption is enabled. A value of 'false' indicates that, link encryption is disabled.
T/F cLHaNetworkFailOver	1.3.6.1.4.1.9.9.843.1.1.14	TruthValue	read-write	This object specifies whether network failover is enabled or disabled. A value of 'true' indicates that, network failover is enabled. A value of 'false' indicates that, network failover is disabled.
IP cLHaRFStatusUnitIp	1.3.6.1.4.1.9.9.843.1.1.15	InetAddress	read-only	This object specifies the peer IP address when Redundancy Framwork(RF) state of active/peer unit changes.
U32 cLHaKATimeout	1.3.6.1.4.1.9.9.843.1.1.16	Unsigned32	read-write	This object specifies keep alive timeout value in milli seconds between 100 and 1000. The value for this object configured in multiples of 50.
U32 cLHaKARetryCount	1.3.6.1.4.1.9.9.843.1.1.17	Unsigned32	read-write	This object specifies keep alive retry count and The value for this object configured between 3 and 10.
U32 cLHaGwRetryCount	1.3.6.1.4.1.9.9.843.1.1.18	Unsigned32	read-write	This object specifies default gateway reachability retry count and The value for this object configured between 6 and 12.
U32 cLHaPeerSearchTimeout	1.3.6.1.4.1.9.9.843.1.1.19	Unsigned32	read-write	This object specifies peer search timeout and The value for this object configured between 60 and 300 seconds.
IPt cLHaRFStatusUnitIpType	1.3.6.1.4.1.9.9.843.1.1.20	InetAddressType	read-only	This object specifies the peer IP address type when redundancy framwork(RF) state of active/peer unit changes.
ciscoLwappHaNetworkConfig	1.3.6.1.4.1.9.9.843.1.2
cLHaNetworkRoutePeerConfigTable	1.3.6.1.4.1.9.9.843.1.2.1		not-accessible	This table represents the peer network route entries.
cLHaNetworkRoutePeerConfigEntry	1.3.6.1.4.1.9.9.843.1.2.1.1		not-accessible	Each entry contains configuration of peer network route.
IPt cLHaNetworkRoutePeerIPAddressType	1.3.6.1.4.1.9.9.843.1.2.1.1.1	InetAddressType	not-accessible	This object represents peer network route IP address type.
IP cLHaNetworkRoutePeerIPAddress	1.3.6.1.4.1.9.9.843.1.2.1.1.2	InetAddress	not-accessible	This object represents peer network route IP address.
IPt cLHaNetworkRoutePeerIPNetmaskType	1.3.6.1.4.1.9.9.843.1.2.1.1.3	InetAddressType	read-create	This object specifies peer network route IP netmask type.
IP cLHaNetworkRoutePeerIPNetmask	1.3.6.1.4.1.9.9.843.1.2.1.1.4	InetAddress	read-create	This object specifies peer network route IP netmask.
IPt cLHaNetworkRoutePeerGatewayType	1.3.6.1.4.1.9.9.843.1.2.1.1.5	InetAddressType	read-create	This object represents peer network route gateway IP type.
IP cLHaNetworkRoutePeerGateway	1.3.6.1.4.1.9.9.843.1.2.1.1.6	InetAddress	read-create	This object specifies peer network route gateway IP address.
INT cLHaNetworkRoutePeerTransferStatus	1.3.6.1.4.1.9.9.843.1.2.1.1.7	INTEGER	read-only	This object represents peer network route transfer status. A value of initiate(1) indicates that, network route transfer initiated. A value of inProgress(2) indicates that, network route transfer in progress. A value of success(3) indicates that, network route transfer success. A value of failure(4) indicates that, network route transfer failure. A value of timeout(5) indicates that network route transfer time out.
ROW cLHaNetworkRoutePeerRowStatus	1.3.6.1.4.1.9.9.843.1.2.1.1.8	RowStatus	read-create	This object specifies status column for this row and used to create and delete specific instances of rows in this table.
ciscoLwappHaNotificationVariable	1.3.6.1.4.1.9.9.843.1.3
INT cLHaSecondaryControllerUsageTrapType	1.3.6.1.4.1.9.9.843.1.3.1	INTEGER	read-only	This object represents the usage of secondary controller. After the usuage of 90 days, one trap is generated per day for over usage. A value of usageStart(1) indicates that, start of secondary controller usage. A value of usageComplete(2) indicates, that completion of secondary controller usage period of 90 days. A value of overUsage(3) indicates that, Secondary controller overusage.
C32 cLHaSecondaryControllerUsageDayCounterEx	1.3.6.1.4.1.9.9.843.1.3.2	Counter32	read-only	This object represents the number of days the secondary controller is used.
INT cLHaBulkSyncCompleteEvent	1.3.6.1.4.1.9.9.843.1.3.3	INTEGER	read-only	This object represents the time when the bulksync was complete.
INT cLHaPeerHotStandbyEvent	1.3.6.1.4.1.9.9.843.1.3.4	INTEGER	read-only	This object represents that the peer has turned hot-standby.
ciscoLwappHaPeerStatisticsVariable	1.3.6.1.4.1.9.9.843.1.4
ciscoLwappHaSystemStatistics	1.3.6.1.4.1.9.9.843.1.4.1
ciscoLwappHaCpuStatistics	1.3.6.1.4.1.9.9.843.1.4.1.1
STR cLHaAllCpuUsage	1.3.6.1.4.1.9.9.843.1.4.1.1.1	SnmpAdminString	read-only	This object represents the all CPUs usage of peer.
ciscoLwappHaPowerSupplyStatistics	1.3.6.1.4.1.9.9.843.1.4.1.2
T/F cLHaPowerSupply1Present	1.3.6.1.4.1.9.9.843.1.4.1.2.1	TruthValue	read-only	This object represents whether peer switch power Supply 1 is enabled or disabled. A value of 'true' indicates that, peer switch power supply 1 is enabled. A value of 'false' indicates that, peer switch power supply 1 is disabled.
T/F cLHaPowerSupply1Operational	1.3.6.1.4.1.9.9.843.1.4.1.2.2	TruthValue	read-only	This object represents whether peer switch power supply 1 operational or not. A value of 'true' indicates that, peer switch power supply 1 operational is enabled. A value of 'false' indicates that, peer switch power supply 1 operational is disabled.
T/F cLHaPowerSupply2Present	1.3.6.1.4.1.9.9.843.1.4.1.2.3	TruthValue	read-only	This object represents whether peer switch power supply 2 is enabled or disabled. A value of 'true' indicates that, peer switch power supply 2 is enabled. A value of 'false' indicates that, peer switch power supply 2 is disabled.
T/F cLHaPowerSupply2Operational	1.3.6.1.4.1.9.9.843.1.4.1.2.4	TruthValue	read-only	This object represents whether Peer switch power Supply 2 operational or not. A value of 'true' indicates that, peer switch power supply 2 operational is enabled. A value of 'false' indicates that, peer switch power supply 2 operational is disabled.
ciscoLwappHaMemoryStatistics	1.3.6.1.4.1.9.9.843.1.4.1.3
I32 cLHaTotalSystemMemory	1.3.6.1.4.1.9.9.843.1.4.1.3.1	Integer32	read-only	This object represents the total system memory in Kbytes.
I32 cLHaFreeSystemMemory	1.3.6.1.4.1.9.9.843.1.4.1.3.2	Integer32	read-only	This object represents the free system memory in Kbytes.
I32 cLHaUsedSystemMemory	1.3.6.1.4.1.9.9.843.1.4.1.3.3	Integer32	read-only	This object represents the used system memory in Kbytes.
I32 cLHaAllocatedFromRtos	1.3.6.1.4.1.9.9.843.1.4.1.3.4	Integer32	read-only	This object represents the number of bytes allocated from RTOS in Kbytes.
I32 cLHaChunksFree	1.3.6.1.4.1.9.9.843.1.4.1.3.5	Integer32	read-only	This object represents the number of free chunks.
I32 cLHaMmappedRegions	1.3.6.1.4.1.9.9.843.1.4.1.3.6	Integer32	read-only	This object represents the number of memory mapped regions.
I32 cLHaSpaceInMmappedRegions	1.3.6.1.4.1.9.9.843.1.4.1.3.7	Integer32	read-only	This object represents the space in the memory mapped regions in Kbytes.
I32 cLHaTotalAllocatedSpace	1.3.6.1.4.1.9.9.843.1.4.1.3.8	Integer32	read-only	This object represents the total allocated space in Kbytes.
I32 cLHaTotalNotInUseSpace	1.3.6.1.4.1.9.9.843.1.4.1.3.9	Integer32	read-only	This object represents the total space not in-use in Kbytes.
I32 cLHaTopMostReleasableSpace	1.3.6.1.4.1.9.9.843.1.4.1.3.10	Integer32	read-only	This object represents the top most releasable space in Kbytes.
I32 cLHaTotalAllocatedInclMmap	1.3.6.1.4.1.9.9.843.1.4.1.3.11	Integer32	read-only	This object represents the total memory allocated including memory map in Kbytes.
I32 cLHaTotalUsedMmap	1.3.6.1.4.1.9.9.843.1.4.1.3.12	Integer32	read-only	This object represents the total memory in-use including memory map in Kbytes.
I32 cLHaTotalFreeInclMmap	1.3.6.1.4.1.9.9.843.1.4.1.3.13	Integer32	read-only	This object represents the total free memory including memory map in Kbytes.
ciscoLwappHaStatisticsVariable	1.3.6.1.4.1.9.9.843.1.5
I32 cLHaAvgPeerReachLatency	1.3.6.1.4.1.9.9.843.1.5.1	Integer32	read-only	This object represents average value of peer controller reachable latency in micro seconds.
I32 cLHaAvgGwReachLatency	1.3.6.1.4.1.9.9.843.1.5.2	Integer32	read-only	This object represents average value of default gate way reachable latency in micro seconds.
STR cLHaBulkSyncStatus	1.3.6.1.4.1.9.9.843.1.5.3	SnmpAdminString	read-only	This object represents current status of bulk sync.
ciscoLwappMcHaConfig	1.3.6.1.4.1.9.9.843.1.6
STR cLMcHaPortName	1.3.6.1.4.1.9.9.843.1.6.1	DisplayString	read-write	This object allows user to specify and get the interface name designated as the HA Interface in Multi-Chassis HA environments. This will be applicable only on the virtual Chassis systems. This should be the complete namestring of the chassis interface.
IPt cLMcHaPortLocIpAddrType	1.3.6.1.4.1.9.9.843.1.6.2	InetAddressType	read-write	This object represents the IP version to be used for HA transport. This object will apply to both local IP and the cLMcHaPortMask
IP cLMcHaPortLocIp	1.3.6.1.4.1.9.9.843.1.6.3	InetAddress	read-write	This object allows user to specify and get the Local chassis IPv4 Address to establish the HA communication. This IP Address will be assigned to the HA Port on the configuring chassis, and it will be take effect only after a reload.
IP cLMcHaPortMask	1.3.6.1.4.1.9.9.843.1.6.4	InetAddress	read-write	This object allows user to specify and get the network mask for the local chassis IPv4 Address to establish the HA communication. This netmask will be assigned to designated HA interface.
IPt cLMcHaPortRemoteIpAddrType	1.3.6.1.4.1.9.9.843.1.6.5	InetAddressType	read-write	This object represents the IP version to be used for HA transport.
IP cLMcHaPortRemIp	1.3.6.1.4.1.9.9.843.1.6.6	InetAddress	read-write	This object allows user to specify and get the peer chassis IPv4 Address to establish the HA communication.
U32 cLMcHaKeepAliveTimeOut	1.3.6.1.4.1.9.9.843.1.6.7	Unsigned32	read-write	This object specifies keep alive timeout value in milli seconds between 100 and 1000. The value for this object configured in multiples of 100.
U32 cLMcHaChassisPriority	1.3.6.1.4.1.9.9.843.1.6.8	Unsigned32	read-write	This object allows user to specify and get the current chassis priority. The higher the priority, higher the chance of local chassis becoming the Active.
T/F cLMcHaClearConfig	1.3.6.1.4.1.9.9.843.1.6.9	TruthValue	read-write	This object allows user to remove the multi-chassis HA configuration. When get, TRUE value indicating HA configuration is cleared, FALSE means not.
U32 cLMcHaKeepAliveRetryCount	1.3.6.1.4.1.9.9.843.1.6.10	Unsigned32	read-write	This object specifies keep alive retry count and The value for this object configured between 3 and 10.
ciscoLwappMcRmiConfig	1.3.6.1.4.1.9.9.843.1.7
U32 cLMcRmiConfigAction	1.3.6.1.4.1.9.9.843.1.7.1	Unsigned32	read-write	This object allows user to remove the RMI configuration. When get, 1 value indicating RMI configuration is applied , 2 means clear config.
STR cLMcRmiInterface	1.3.6.1.4.1.9.9.843.1.7.2	SnmpAdminString	read-write	This object specifies Chassis/Switch number and The value for this object is between 1 and 15.
U32 cLMcRmiChassisANum	1.3.6.1.4.1.9.9.843.1.7.3	Unsigned32	read-write	This object specifies Chassis/Switch number and The value for this object is between 1 and 15.
IPt cLMcRmiChassisAIpAddrType	1.3.6.1.4.1.9.9.843.1.7.4	InetAddressType	read-write	This object represents IP version to be used for RMI transport
IP cLMcRmiChassisAIp	1.3.6.1.4.1.9.9.843.1.7.5	InetAddress	read-write	This object allows user to specify and get the chassis. IPv4 Address to establish the RMI communication. This IP Address will be assigned to the RMI Port on the configuring chassis, and it will be take effect only after a reload.
U32 cLMcRmiChassisBNum	1.3.6.1.4.1.9.9.843.1.7.6	Unsigned32	read-write	This object specifies Chassis/Switch number and The value for this object is between 1 and 15.
IPt cLMcRmiChassisBIpAddrType	1.3.6.1.4.1.9.9.843.1.7.7	InetAddressType	read-write	This object represents IP version to be used for RMI transport
IP cLMcRmiChassisBIp	1.3.6.1.4.1.9.9.843.1.7.8	InetAddress	read-write	This object allows user to specify and get the chassis. IPv4 Address to establish the RMI communication. This IP Address will be assigned to the RMI Port on the configuring chassis, and it will be take effect only after a reload.
T/F cLMcRmiGatewayFailover	1.3.6.1.4.1.9.9.843.1.7.9	TruthValue	read-write	This object allows user to enable/disable RMI Gateway-Failover configuration. When get, TRUE value indicating RMI Gateway-Failover configuration is enabled, FALSE means disabled.
U32 cLMcRmiGatewayFailoverInterval	1.3.6.1.4.1.9.9.843.1.7.10	Unsigned32	read-write	This object specifies Gateway-Failover interval and The value for this object is between 6 and 12.
ciscoLwappHaMIBConform	1.3.6.1.4.1.9.9.843.2
ciscoLwappHaMIBCompliances	1.3.6.1.4.1.9.9.843.2.1
ciscoLwappHaMIBCompliance	1.3.6.1.4.1.9.9.843.2.1.1			This is a default module-compliance containing default object groups.
ciscoLwappHaMIBComplianceRev1	1.3.6.1.4.1.9.9.843.2.1.2			This is a default module-compliance containing default object groups.
ciscoLwappHaMIBGroups	1.3.6.1.4.1.9.9.843.2.2
ciscoLwappHaGlobalConfigGroup	1.3.6.1.4.1.9.9.843.2.2.1			This collection of objects represents the information about global config of the high availability objects on the controller.
ciscoLwappHaNetworkConfigGroup	1.3.6.1.4.1.9.9.843.2.2.2			This collection of objects represents the information about network config of the high availability objects on the controller.
ciscoLwappHaStatisticsGroup	1.3.6.1.4.1.9.9.843.2.2.3			This collection of objects represents the information about the Statistics of high availability objects on the controller.
ciscoLwappHaMIBNotificationVariableGroup	1.3.6.1.4.1.9.9.843.2.2.4			This collection of objects represents the information about the Notification of high availability objects on the controller.
ciscoLwappHaMIBNotificationGroup	1.3.6.1.4.1.9.9.843.2.2.5			This supplemental collection of objects represents the HA related notifications sent by the agent to a network management station.
ciscoLwappMcHaConfigGroup	1.3.6.1.4.1.9.9.843.2.2.6			This collection of objects represents the information about network config of the multi chassis high availability RMI objects on the controller.
ciscoLwappMcRmiConfigGroup	1.3.6.1.4.1.9.9.843.2.2.7			This collection of objects represents the information about network config of the multi chassis RMI objects on the controller.

RFC description

Cisco Lightweight Access Point Protocol (LWAPP) high-availability MIB for Cisco wireless controllers managing redundancy and failover.

Start monitoring Cisco Wireless LAN Controller (WLC) pair configured for HA/SSO with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-LWAPP-HA-MIB