CISCO-DYNAMIC-TEMPLATE-MIB

All MIBs › CISCO-DYNAMIC-TEMPLATE-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2007-09-06

Category: Cisco Devices, Device Management

Description: Manages dynamic subscriber policy templates on Cisco IOS/IOS-XE, controlling per-subscriber service activation and parameter assignment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-DYNAMIC-TEMPLATE-MIB?

CISCO-DYNAMIC-TEMPLATE-MIB is a Cisco proprietary SNMP module for IOS/IOS-XE platforms that manages dynamic templates, reusable sets of configuration attributes that can be applied on the fly to a target, most commonly a subscriber-facing interface. It exposes a template table describing each template's name, storage type, source, status, and usage count, along with a target table mapping templates to the entities (currently interfaces) they are applied to. Its monitoring/management role is configuration and operational-state tracking rather than hardware sensors: cdtTemplateStatus and cdtTemplateUsageCount let an admin confirm a template is active and see how widely it is applied, while cdtTemplateTargetTable shows exactly which targets (by type and ID) currently have a given template bound to them. It builds on Cisco's broader subscriber-session and interface architecture since templates are applied to interface-like targets. It is typically deployed in Broadband Network Gateway (BNG) or edge-router environments doing dynamic, per-subscriber service activation such as bandwidth or QoS policy changes triggered by RADIUS/COA. Engineers can download the CISCO-DYNAMIC-TEMPLATE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-DYNAMIC-TEMPLATE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco IOS/IOS-XE router
Broadband Network Gateway (BNG)/subscriber edge router

Monitoring Examples

An operator troubleshooting inconsistent subscriber service would query cdtTemplateTable/cdtTemplateEntry for a given cdtTemplateName to check cdtTemplateStatus (active/inactive) and cdtTemplateUsageCount, then cross-reference cdtTemplateTargetTable/cdtTemplateTargetEntry using cdtTemplateTargetType and cdtTemplateTargetId to confirm which specific interface has that template applied. A usage count of zero when a subscriber policy change was expected to apply would indicate the template failed to bind to its target, while ciscoDynamicTemplateMIBNotifs would carry any related trap for template application failures. cdtTemplateSrc helps identify whether the template originated from local configuration or a dynamic source like RADIUS.

What Can Be Monitored

template name/status
template usage count
template storage type
template-to-target bindings
target type and ID
template source

Imported Objects

From CISCO-CBP-TC-MIB

CbpElementName

From CISCO-DYNAMIC-TEMPLATE-TC-MIB

DynamicTemplateName
DynamicTemplateTargetId
DynamicTemplateTargetType
DynamicTemplateType

From CISCO-IP-URPF-MIB

UnicastRpfOptions
UnicastRpfType

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From CISCO-TC

CiscoVrfName

From IF-MIB

InterfaceIndexOrZero

From INET-ADDRESS-MIB

InetAddressIPv4
InetAddressIPv6
InetAddressPrefixLength

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
StorageType
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
cdtBase	1.3.6.1.4.1.9.9.784.1.1
cdtBaseGroup	1.3.6.1.4.1.9.9.784.2.2.1			This group contains objects describing dynamic templates, targets of dynamic templates, and the associations between dynamic templates and targets.
STR cdtCommonAddrPool	1.3.6.1.4.1.9.9.784.1.1.5.1.6	SnmpAdminString	read-create	This object specifies the name of the IP address pool the system will use to assign an IP address to a peer of a target. This column is valid only if the 'addrPool' bit of the corresponding instance of cdtCommonValid is '1'.
STR cdtCommonDescr	1.3.6.1.4.1.9.9.784.1.1.5.1.2	SnmpAdminString	read-create	This object specifies a human-readable description for the dynamic template. This column is valid only if the 'descr' bit of the corresponding instance of cdtCommonValid is '1'.
cdtCommonGroup	1.3.6.1.4.1.9.9.784.2.2.2			This group contains objects describing attributes common to all dynamic templates.
cdtCommonIf	1.3.6.1.4.1.9.9.784.1.2
STR cdtCommonIpv4AccessGroup	1.3.6.1.4.1.9.9.784.1.1.5.1.7	SnmpAdminString	read-create	This object specifies the name (or number) of the IPv4 ACL applied to a target. This column is valid only if the 'ipv4AccessGroup' bit of the corresponding instance of cdtCommonValid is '1'.
T/F cdtCommonIpv4Unreachables	1.3.6.1.4.1.9.9.784.1.1.5.1.8	TruthValue	read-create	This object specifies whether a target generates ICMPv4 unreachable messages. This column is valid only if the 'ipv4Unreachables' bit of the corresponding instance of cdtCommonValid is '1'.
STR cdtCommonIpv6AccessGroup	1.3.6.1.4.1.9.9.784.1.1.5.1.9	SnmpAdminString	read-create	This object specifies the name (or number) of the IPv4 ACL applied to a target. This column is valid only if the 'ipv6AccessGroup' bit of the corresponding instance of cdtCommonValid is '1'.
T/F cdtCommonIpv6Unreachables	1.3.6.1.4.1.9.9.784.1.1.5.1.10	TruthValue	read-create	This object specifies whether a target generates ICMPv6 unreachable messages. This column is valid only if the 'ipv6Unreachables' bit of the corresponding instance of cdtCommonValid is '1'.
U32 cdtCommonKeepaliveInt	1.3.6.1.4.1.9.9.784.1.1.5.1.3	Unsigned32	read-create	This object specifies the interval that the system sends keepalive messages to a target. This column is valid only if the 'keepaliveInterval' bit of the corresponding instance of cdtCommonValid is '1'.
U32 cdtCommonKeepaliveRetries	1.3.6.1.4.1.9.9.784.1.1.5.1.4	Unsigned32	read-create	This object specifies the number of times the system will resend a keepalive message without a response before it transitions a target to an operationally down state. This column is valid only if the 'keepaliveRetries' bit of the corresponding instance of cdtCommonValid is '1'.
CBP cdtCommonSrvAcct	1.3.6.1.4.1.9.9.784.1.1.5.1.13	CbpElementName	read-create	This object specifies the name of the traffic accounting policy applied to a target. The system should assume that the cbpPolicyMapType (defined by the CISCO-CBP-BASE-CFG-MIB) of the policy is cbpPmtTrafficAccounting (defined by the CISCO-CBP-TYPE-OID-MIB). This column is valid only if the 'srvAcct' bit of the corresponding instance of cdtCommonValid is '1'.
CBP cdtCommonSrvNetflow	1.3.6.1.4.1.9.9.784.1.1.5.1.15	CbpElementName	read-create	This object specifies the name of the NetFlow policy applied to a target. The system should assume that the cbpPolicyMapType (defined by the CISCO-CBP-BASE-CFG-MIB) of the policy is cbpPmtNetflow (defined by the CISCO-CBP-TYPE-OID-MIB). This column is valid only if the 'srvNetflow' bit of the corresponding instance of cdtCommonValid is '1'.
CBP cdtCommonSrvQos	1.3.6.1.4.1.9.9.784.1.1.5.1.14	CbpElementName	read-create	This object specifies the name of the traffic QoS policy applied to a target. The system should assume that the cbpPolicyMapType (defined by the CISCO-CBP-BASE-CFG-MIB) of the policy is cbpPmtQos (defined by the CISCO-CBP-TYPE-OID-MIB). This column is valid only if the 'srvQos' bit of the corresponding instance of cdtCommonValid is '1'.
CBP cdtCommonSrvRedirect	1.3.6.1.4.1.9.9.784.1.1.5.1.12	CbpElementName	read-create	This object specifies the name of the traffic redirect policy applied to a target. The system should assume that the cbpPolicyMapType (defined by the CISCO-CBP-BASE-CFG-MIB) of the policy is cbpPmtTrafficRedirect (defined by the CISCO-CBP-TYPE-OID-MIB). This column is valid only if the 'srvRedirect' bit of the corresponding instance of cdtCommonValid is '1'.
CBP cdtCommonSrvSubControl	1.3.6.1.4.1.9.9.784.1.1.5.1.11	CbpElementName	read-create	This object specifies the name of the subscriber control policy applied to a target. The system should assume that the cbpPolicyMapType (defined by the CISCO-CBP-BASE-CFG-MIB) of the policy is cbpPmtControlSubscriber (defined by the CISCO-CBP-TYPE-OID-MIB). This column is valid only if the 'srvSubControl' bit of the corresponding instance of cdtCommonValid is '1'.
BIT cdtCommonValid	1.3.6.1.4.1.9.9.784.1.1.5.1.1	Bits	read-create	This object specifies which attributes in the dynamic template have been configured to valid values. Each bit in this bit string corresponds to a column in this table. If the bit is '0', then the value of the corresponding column is not valid. If the bit is '1', then the value of the corresponding column has been configured to a valid value. The following list specifies the mappings between bits and the columns: 'descr' => cdtCommonDescr 'keepaliveInt' => cdtCommonKeepaliveInt 'keepaliveRetries' => cdtCommonKeepaliveRetries 'vrf' => cdtCommonVrf 'addrPool' => cdtCommonAddrPool 'ipv4AccessGroup' => cdtCommonIpv4AccessGroup 'ipv4Unreachables' => cdtCommonIpv4Unreachables 'ipv6AccessGroup' => cdtCommonIpv6AccessGroup 'ipv6Unreachables' => cdtCommonIpv6Unreachables 'srvSubControl' => cdtCommonSrvSubControl 'srvRedirect' => cdtCommonSrvRedirect 'srvAcct' => cdtCommonSrvAcct 'srvQos' => cdtCommonSrvQos 'srvNetflow' => cdtCommonSrvNetflow
CIS cdtCommonVrf	1.3.6.1.4.1.9.9.784.1.1.5.1.5	CiscoVrfName	read-create	This object specifies the name of the VRF with which a target has an association. This column is valid only if the 'vrf' bit of the corresponding instance of cdtCommonValid is '1'.
cdtEthernet	1.3.6.1.4.1.9.9.784.1.4
STR cdtEthernetBridgeDomain	1.3.6.1.4.1.9.9.784.1.4.1.1.2	SnmpAdminString	read-create	This object specifies the name of the bridge domain...
cdtEthernetGroup	1.3.6.1.4.1.9.9.784.2.2.5			This group contains objects describing attributes contained by Ethernet templates.
T/F cdtEthernetIpv4PointToPoint	1.3.6.1.4.1.9.9.784.1.4.1.1.4	TruthValue	read-create	This object specifies whether...
MAC cdtEthernetMacAddr	1.3.6.1.4.1.9.9.784.1.4.1.1.5	MacAddress	read-create	This object specifies the...
T/F cdtEthernetPppoeEnable	1.3.6.1.4.1.9.9.784.1.4.1.1.3	TruthValue	read-create	This object specifies whether...
cdtEthernetTemplateEntry	1.3.6.1.4.1.9.9.784.1.4.1.1		not-accessible	An entry containing attributes relating to dynamic interfaces initiated on Ethernet virtual interfaces (e.g., EoMPLS) or automatically created VLANs. The system automatically creates an entry when the system or the EMS/NMS creates a row in the cdtTemplateTable with a cdtTemplateType of one of the following values: 'derived' 'ethernet' Likewise, the system automatically destroys an entry when the system or the EMS/NMS destroys the corresponding row in the cdtTemplateTable.
cdtEthernetTemplateTable	1.3.6.1.4.1.9.9.784.1.4.1		not-accessible	This table contains attributes relating to dynamic interfaces initiated on Ethernet virtual interfaces (e.g., EoMPLS) or automatically created VLANs. This table has a sparse-dependent relationship on the cdtTemplateTable, containing a row for each dynamic template having a cdtTemplateType of one of the following values: 'derived' 'ethernet'
BIT cdtEthernetValid	1.3.6.1.4.1.9.9.784.1.4.1.1.1	Bits	read-create	This object specifies which attributes in the dynamic template have been configured to valid values. Each bit in this bit string corresponds to a column in this table. If the bit is '0', then the value of the corresponding column is not valid. If the bit is '1', then the value of the corresponding column has been configured to a valid value. The following list specifies the mappings between bits and the columns: bridgeDomain => cdtEthernetBridgeDomain pppoeEnable => cdtEthernetPppoeEnable ipv4PointToPoint => cdtEthernetIpv4PointToPoint macAddr => cdtEthernetMacAddr
T/F cdtIfCdpEnable	1.3.6.1.4.1.9.9.784.1.2.1.1.3	TruthValue	read-create	This object specifies whether the target interface participates in the Cisco Discovery Protocol (CDP). This column is valid only if the 'cdpEnable' bit of the corresponding instance of cdtIfValid is '1'.
STR cdtIfFlowMonitor	1.3.6.1.4.1.9.9.784.1.2.1.1.4	SnmpAdminString	read-create	This object specifies the name of the flow monitor associated with the target interface. This column is valid only if the 'flowMonitor' bit of the corresponding instance of cdtIfValid is '1'.
cdtIfGroup	1.3.6.1.4.1.9.9.784.2.2.3			This group contains objects describing attributes common to dynamic templates applied to dynamic interfaces.
U32 cdtIfIpv4Mtu	1.3.6.1.4.1.9.9.784.1.2.1.1.7	Unsigned32	read-create	This object specifies the Maximum Transfer Unit (MTU) size for IPv4 packets sent on the target interface. The value '0' cannot be written to an instance of this object. However, it serves as a convenient value when the column is not valid. This column is valid only if the 'ipv4Mtu' bit of the corresponding instance of cdtIfValid is '1'.
T/F cdtIfIpv4SubEnable	1.3.6.1.4.1.9.9.784.1.2.1.1.6	TruthValue	read-create	This object specifies whether the target interface allows IPv4 subscriber sessions. This column is valid only if the 'ipv4SubEnable' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv4TcpMssAdjust	1.3.6.1.4.1.9.9.784.1.2.1.1.8	Unsigned32	read-create	This object specifies the adjustment to the Maximum Segment Size (MSS) of TCP SYN packets received by the target interface contained in IPv4 datagrams. The value '0' cannot be written to an instance of this object. However, it serves as a convenient value when the column is not valid. This column is valid only if the 'ipv4TcpMssAdjust' bit of the corresponding instance of cdtIfValid is '1'.
NUM cdtIfIpv4Unnumbered	1.3.6.1.4.1.9.9.784.1.2.1.1.5	InterfaceIndexOrZero	read-create	This object specifies the interface of the source address that the target interface uses when originating IPv4 packets. The value '0' cannot be written to an instance of this object. However, it serves as a convenient value when the column is not valid (e.g., immediately following the creation of an instance of the object). This column is valid only if the 'ipv4Unnumbered' bit of the corresponding instance of cdtIfValid is '1'.
UNI cdtIfIpv4VerifyUniRpf	1.3.6.1.4.1.9.9.784.1.2.1.1.9	UnicastRpfType	read-create	This object specifies whether the type of unicast RPF the system performs on IPv4 packets received by the target interface. This column is valid only if the 'ipv4VerifyUniRpf' bit of the corresponding instance of cdtIfValid is '1'.
STR cdtIfIpv4VerifyUniRpfAcl	1.3.6.1.4.1.9.9.784.1.2.1.1.10	SnmpAdminString	read-create	This object specifies the name (or number) of the IPv4 ACL used to determine whether the system should permit/deny packets received by the target interface that fail unicast RPF verification. This column is valid only if the 'ipv4VerifyUniRpfAcl' bit of the corresponding instance of cdtIfValid is '1'.
UNI cdtIfIpv4VerifyUniRpfOpts	1.3.6.1.4.1.9.9.784.1.2.1.1.11	UnicastRpfOptions	read-create	This object specifies the options that affect how the system performs unicast RPF on IPv4 packets received by the target interface. This column is valid only if the 'ipv4VerifyUniRpfOpts' bit of the corresponding instance of cdtIfValid is '1'.
T/F cdtIfIpv6Enable	1.3.6.1.4.1.9.9.784.1.2.1.1.12	TruthValue	read-create	This object specifies whether the system processes IPv6 packets received by the target interface. This column is valid only if the 'ipv6Enable' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv6NdDadAttempts	1.3.6.1.4.1.9.9.784.1.2.1.1.23	Unsigned32	read-create	This object specifies the number of consecutive neighbor solitication messages the system sends on the target interface while performing duplicate address detection on unicast IPv6 addresses on the target interface. The value '0' disables duplicate address detection on the target interface. This column is valid only if the 'ipv6NdDadAttempts' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv6NdNsInterval	1.3.6.1.4.1.9.9.784.1.2.1.1.24	Unsigned32	read-create	This object specifies the interval between neighbor solicitation retransmissions on the target interface. This column is valid only if the 'ipv6NdNsIntervals' bit of the corresponding instance of cdtIfValid is '1'.
BIT cdtIfIpv6NdOpts	1.3.6.1.4.1.9.9.784.1.2.1.1.22	Bits	read-create	This object specifies options that affect advertisements sent on the target interface: 'advertise' This option specifies that the system should advertise the IPv6 prefix (i.e., the corresponding instance of cdtIfIpv6NdPrefix). 'onlink' This option specifies that the IPv6 prefix has been assigned to a link. If set to '0', the system advertises the IPv6 prefix as 'offlink'. 'router' This option indicates that the router will send the full router address and not set the 'R' bit in prefix advertisements. 'autoConfig' This option indicates to hosts on the local link that the specified prefix supports IPv6 auto-configuration. 'advertisementInterval' This option specifies the advertisement interval option in router advertisements sent on the target interface. 'managedConfigFlag' This option causes the system to set the 'managed address configuration flag' in router advertisements sent on the target interface. 'otherConfigFlag' This option causes the system to set the 'other stateful configuration' flag in router advertisements sent on the target interface. 'frameIpv6Prefix' This option causes the system to add the prefix in a received RADIUS framed IPv6 prefix attribute to the target interface's neighbor discovery prefix queue and includes it in router advertisements sent on the target interface. 'raSupress' This option suppresses the transmission of router advertisements on the target interface. This column is valid only if the 'ipv6NdOpts' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv6NdPreferredLife	1.3.6.1.4.1.9.9.784.1.2.1.1.21	Unsigned32	read-create	This object specifies the interval that the system advertises the IPv6 prefix (i.e., the corresponding instance of cdtIfIpv6NdPrefix) as 'preferred' for IPv6 router advertisements sent on the target interface. This column is valid only if the 'ipv6NdPreferredLife' bit of the corresponding instance of cdtIfValid is '1'.
ADR cdtIfIpv6NdPrefix	1.3.6.1.4.1.9.9.784.1.2.1.1.18	InetAddressIPv6	read-create	This object specifies the IPv6 network number included in IPv6 router advertisements sent on the target interface. This column is valid only if the 'ipv6NdPrefix' bit of the corresponding instance of cdtIfValid is '1'.
ADR cdtIfIpv6NdPrefixLength	1.3.6.1.4.1.9.9.784.1.2.1.1.19	InetAddressPrefixLength	read-create	This object specifies the length of the IPv6 prefix specified by the corresponding instance of cdtIpv6NdPrefix. This column is valid only if the 'ipv6NdPrefix' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv6NdRaIntervalMax	1.3.6.1.4.1.9.9.784.1.2.1.1.27	Unsigned32	read-create	This object specifies the maximum interval between IPv6 router advertisements sent on the target interface. The value '0' cannot be written to an instance of this object. However, it serves as a convenient value when the column is not valid. This column is valid only if the 'ipv6NdRaInterval' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv6NdRaIntervalMin	1.3.6.1.4.1.9.9.784.1.2.1.1.28	Unsigned32	read-create	This object specifies the minimum interval between IPv6 router advertisements sent on the target interface. The value of this column has the following restrictions: 1) This value cannot be less than 75% of the value specified for cdtIfIpv6NdRaIntervalMax. 2) If the corresponding instance of cdtIfIpv6NdRaIntervalUnits is 'seconds', then this value cannot be less than '3'. 3) If the corresponding instance of cdtIfIpv6NdRaIntervalUnits is 'milliseconds', then this value cannot be less than '30'. If the target interface template does not specify this value, then the system automatically assumes a minimum interval that is 75% of the corresponding instance of cdtIfIpv6NdRaIntervalMax. The value '0' cannot be written to an instance of this object. However, it serves as a convenient value when the column is not valid. This column is valid only if the 'ipv6NdRaInterval' bit of the corresponding instance of cdtIfValid is '1'.
INT cdtIfIpv6NdRaIntervalUnits	1.3.6.1.4.1.9.9.784.1.2.1.1.26	INTEGER	read-create	This object specifies the units of time for the corresponding instances of cdtIfIpv6NdRaIntervalMin and cdtIfIpv6NdRaIntervalMax. This column is valid only if the 'ipv6NdRaInterval' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv6NdRaLife	1.3.6.1.4.1.9.9.784.1.2.1.1.29	Unsigned32	read-create	This object specifies the router lifetime value in IPv6 router advertisements sent on the target interface. The value '0' specifies that neighbors should not consider the router as a default router.
U32 cdtIfIpv6NdReachableTime	1.3.6.1.4.1.9.9.784.1.2.1.1.25	Unsigned32	read-create	This object specifies the amount of time the system considers a neighbor of the target interface reachable after a reachability confirmation event has occurred. The value '0' disables neighbor reachability detection on the target interface. This column is valid only if the 'ipv6NdReachable' bit of the corresponding instance of cdtIfValid is '1'.
INT cdtIfIpv6NdRouterPreference	1.3.6.1.4.1.9.9.784.1.2.1.1.30	INTEGER	read-create	This object specifies the Default Router Preference (DRP) for the router on the target interface. This column is valid only if the 'ipv6NdRouterPreference' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv6NdValidLife	1.3.6.1.4.1.9.9.784.1.2.1.1.20	Unsigned32	read-create	This object specifies the interval that the system advertises the IPv6 prefix (i.e., the corresponding instance of cdtIfIpv6NdPrefix) as 'valid' for IPv6 router advertisements sent on the target interface. This column is valid only if the 'ipv6NdValidLife' bit of the corresponding instance of cdtIfValid is '1'.
T/F cdtIfIpv6SubEnable	1.3.6.1.4.1.9.9.784.1.2.1.1.13	TruthValue	read-create	This object specifies whether the target interface allows IPv6 subscriber sessions. This column is valid only if the 'ipv6SubEnable' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfIpv6TcpMssAdjust	1.3.6.1.4.1.9.9.784.1.2.1.1.14	Unsigned32	read-create	This object specifies the adjustment to the Maximum Segment Size (MSS) of TCP SYN packets received by the target interface contained in IPv6 datagrams. The value '0' cannot be written to an instance of this object. However, it serves as a convenient value when the column is not valid. This column is valid only if the 'ipv6TcpMssAdjust' bit of the corresponding instance of cdtIfValid is '1'.
UNI cdtIfIpv6VerifyUniRpf	1.3.6.1.4.1.9.9.784.1.2.1.1.15	UnicastRpfType	read-create	This object specifies whether the type of unicast RPF the system performs on IPv6 packets received by the target interface. This column is valid only if the 'ipv6VerifyUniRpf' bit of the corresponding instance of cdtIfValid is '1'.
STR cdtIfIpv6VerifyUniRpfAcl	1.3.6.1.4.1.9.9.784.1.2.1.1.16	SnmpAdminString	read-create	This object specifies the name (or number) of the IPv6 ACL used to determine whether the system should permit/deny packets received by the target interface that fail unicast RPF verification. This column is valid only if the 'ipv6VerifyUniRpfAcl' bit of the corresponding instance of cdtIfValid is '1'.
UNI cdtIfIpv6VerifyUniRpfOpts	1.3.6.1.4.1.9.9.784.1.2.1.1.17	UnicastRpfOptions	read-create	This object specifies the options that affect how the system performs unicast RPF on IPv6 packets received by the target interface. This column is valid only if the 'ipv6VerifyUniRpfOpts' bit of the corresponding instance of cdtIfValid is '1'.
U32 cdtIfMtu	1.3.6.1.4.1.9.9.784.1.2.1.1.2	Unsigned32	read-create	This object specifies the Maximum Transfer Unit (MTU) size for all packets sent on the target interface. The value '0' cannot be written to an instance of this object. However, it serves as a convenient value when the column is not valid. This column is valid only if the 'mtu' bit of the corresponding instance of cdtIfValid is '1'.
cdtIfTemplateEntry	1.3.6.1.4.1.9.9.784.1.2.1.1		not-accessible	An entry containing attributes relating to interface configuration. The system automatically creates an entry when the system or the EMS/NMS creates a row in the cdtTemplateTable with a cdtTemplateType of one of the following values: 'derived' 'ppp' 'ethernet' 'ipSubscriber' Likewise, the system automatically destroys an entry when the system or the EMS/NMS destroys the corresponding row in the cdtTemplateTable.
cdtIfTemplateTable	1.3.6.1.4.1.9.9.784.1.2.1		not-accessible	This table contains attributes relating to interface configuration. This table has a sparse-dependent relationship on the cdtTemplateTable, containing a row for each dynamic template having a cdtTemplateType of one of the following values: 'derived' 'ppp' 'ethernet' 'ipSubscriber'
BIT cdtIfValid	1.3.6.1.4.1.9.9.784.1.2.1.1.1	Bits	read-create	This object specifies which attributes in the dynamic template have been configured to valid values. Each bit in this bit string corresponds to a column in this table. If the bit is '0', then the value of the corresponding column is not valid. If the bit is '1', then the value of the corresponding column has been configured to a valid value. The following list specifies the mappings between bits and the columns: 'mtu' => cdtIfMtu 'cdpEnable' => cdtIfCdpEnable 'flowMonitor' => cdtIfFlowMonitor 'ipv4Unnumbered' => cdtIfIpv4Unnumbered 'ipv4SubEnable' => cdtIfIpv4SubEnable 'ipv4Mtu' => cdtIfIpv4Mtu 'ipv4TcpMssAdjust' => cdtIfIpv4TcpMssAdjust 'ipv4VerifyUniRpf' => cdtIfIpv4VerifyUniRpf 'ipv4VerifyUniRpfAcl' => cdtIfIpv4VerifyUniRpfAcl 'ipv4VerifyUniRpfOpts' => cdtIfIpv4VerifyUniRpfOpts 'ipv6Enable' => cdtIfIpv6Enable 'ipv6SubEnable' => cdtIfIpv6SubEnable 'ipv6TcpMssAdjust' => cdtIfIpv6TcpMssAdjust 'ipv6VerifyUniRpf' => cdtIfIpv6VerifyUniRpf 'ipv6VerifyUniRpfAcl' => cdtIfIpv6VerifyUniRpfAcl 'ipv6VerifyUniRpfOpts' => cdtIfIpv6VerifyUniRpfOpts 'ipv6NdPrefix' => cdtIfIpv6NdPrefix, cdtIfIpv6NdPrefixLength 'ipv6NdValidLife' => cdtIfIpv6NdValidLife 'ipv6NdPreferredLife' => cdtIfIpv6NdPreferredLife 'ipv6NdOpts' => cdtIfIpv6NdOpts 'ipv6NdDadAttempts' => cdtIfIpv6NdDadAttempts 'ipv6NdNsInterval' => cdtIfIpv6NdNsInterval 'ipv6NdReacableTime' => cdtIfIpv6NdReacableTime 'ipv6NdRaIntervalMax' => cdtIfIpv6NdRaIntervalUnits, cdtIfIpv6NdRaIntervalMax 'ipv6NdRaIntervalMin' => cdtIfIpv6NdRaIntervalMin 'ipv6NdRaLife' => cdtIfIpv6NdRaLife 'ipv6NdRouterPreference'' => cdtIfIpv6NdRouterPreference
cdtIpSubscriber	1.3.6.1.4.1.9.9.784.1.5
cdtPpp	1.3.6.1.4.1.9.9.784.1.3
T/F cdtPppAccounting	1.3.6.1.4.1.9.9.784.1.3.1.1.2	TruthValue	read-create	This object specifies whether the system applies accounting services to the target PPP connection. This column is valid only if the 'accounting' bit of the corresponding instance of cdtPppValid is '1'.
BIT cdtPppAuthentication	1.3.6.1.4.1.9.9.784.1.3.1.1.3	Bits	read-create	This object specifies authentication services applied to a target PPP connection and other options affecting authentication services: 'chap' This option enables the Challenge Handshake Protocol (CHAP) on a target PPP connection. 'msChap' This option enables Microsoft's CHAP on a target PPP connection. 'msChapV2' This option enables version 2 of Microsoft's CHAP on a target PPP connection. 'pap' This option enables Password Authentication Protocol (PAP) on a target PPP connection. 'eap' This option enables Extensible Authentication Protocol (EAP) on a target PPP connection. 'optional' This option specifies that the system accepts the connection even if the peer of a target PPP connection refuses to accept the authentication methods the system has requested. 'callin' This option specifies that authentication should only happen for incoming calls. 'oneTime' This option specifies that the system accepts the username and password in the username field of authentication responses received on a target PPP connection. This column is valid only if the 'authentication' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppAuthenticationMethods	1.3.6.1.4.1.9.9.784.1.3.1.1.4	SnmpAdminString	read-create	This object specifies the name of a list of authentication methods used on a target PPP connection. If the template does not include this attribute, then the system uses the default method list. This column is valid only if the 'authentication' bit of the corresponding instance of cdtPppValid is '1'.
T/F cdtPppAuthorization	1.3.6.1.4.1.9.9.784.1.3.1.1.5	TruthValue	read-create	This object specifies whether the system applies authorization services to a target PPP connection. This column is valid only if the 'authorization' bit of the corresponding instance of cditPppValid is '1'.
STR cdtPppChapHostname	1.3.6.1.4.1.9.9.784.1.3.1.1.14	SnmpAdminString	read-create	This object specifies the hostname sent in a CHAP response on a target PPP connection. If the template does not include this attribute, then the system uses its assigned hostname. This column is valid only if the 'chapHostname' bit of the corresponding instance of cdtPppValid is '1'.
BIT cdtPppChapOpts	1.3.6.1.4.1.9.9.784.1.3.1.1.13	Bits	read-create	This object specifies how the system processes the CHAP on a target PPP connection: 'refuse' This option specifies that the system should refuse CHAP requests from peers of a target PPP connection. 'callin' This option specifies that the system should only refuse CHAP requests for incoming calls on a target PPP connection. This option is only relevant if the 'refuse' option is set to '1'. 'wait' This option delays CHAP authentication until after the peer of a target PPP connection has authenticated itself to the system. 'encrypted' This option specifies that the value specified by the corresponding instance of cdtPppChapPassword is already encrypted. This column is valid only if the 'chapOpts' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppChapPassword	1.3.6.1.4.1.9.9.784.1.3.1.1.15	SnmpAdminString	read-create	This object specifies the password used to construct a CHAP response on the target PPP connection. This column is valid only if the 'chapPassword' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppEapIdentity	1.3.6.1.4.1.9.9.784.1.3.1.1.26	SnmpAdminString	read-create	This object specifies the identity sent in an EAP response on a target PPP connection. This column is valid only if the 'eapIdentity' bit of the corresponding instance of cdtPppValid is '1'.
BIT cdtPppEapOpts	1.3.6.1.4.1.9.9.784.1.3.1.1.25	Bits	read-create	This object specifies how the system processes the EAP on a target PPP connection: 'refuse' This option specifies that the system should refuse EAP requests from peers of a target PPP connection. 'callin' This option specifies that the system should only refuse EAP requests for incoming calls on a target PPP connection. This option is only relevant if the 'refuse' option is set to '1'. 'wait' This option delays EAP authentication until after the peer of a target PPP connection has authenticated itself to the system. 'local' This option specifies that the system should locally authenticate the peer of a target PPP connection, rather than acting as a proxy to an external AAA server. This column is valid only if the 'eapOpts' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppEapPassword	1.3.6.1.4.1.9.9.784.1.3.1.1.27	SnmpAdminString	read-create	This object specifies the password used to construct an EAP response on a target PPP connection. This column is valid only if the 'eapPassword' bit of the corresponding instance of cdtPppValid is '1'.
cdtPppGroup	1.3.6.1.4.1.9.9.784.2.2.4			This group contains objects describing attributes contained by PPP templates.
INT cdtPppIpcpAddrOption	1.3.6.1.4.1.9.9.784.1.3.1.1.28	INTEGER	read-create	This object specifies the IPCP address option for a target PPP connection: 'other' The implementation of this MIB module does not recognize the configured IPCP address option. 'accept' The system accepts any non-zero IP address from the peer of a target PPP connection. 'required' The system disconnects the peer of a target PPP connection if it could not negotiate an IP address. 'unique' The system disconnects the peer of a target PPP connection if the IP address is already in use. This column is valid only if the 'ipcpAddrOption' bit of the corresponding instance of cdtPppValid is '1'.
INT cdtPppIpcpDnsOption	1.3.6.1.4.1.9.9.784.1.3.1.1.29	INTEGER	read-create	This object specifies the IPCP DNS option for the dynamic interface: 'other' The implementation of this MIB module does not recognize the configured DNS option. 'accept' The system accepts any non-zero DNS address form the peer of a target PPP connection. 'request' The system requests the DNS address from the peer of a target PPP connection. 'reject' The system rejects the DNS option from the peer of a target PPP connection. This column is valid only if the 'ipcpDnsOption' bit of the corresponding instance of cdtPppValid is '1'.
ADR cdtPppIpcpDnsPrimary	1.3.6.1.4.1.9.9.784.1.3.1.1.30	InetAddressIPv4	read-create	This object specifies the IP address of the primary DNS server offered to the peer of a target PPP connection. This column is valid only if the 'ipcpDnsPrimary' bit of the corresponding instance of cdtPppValid is '1'.
ADR cdtPppIpcpDnsSecondary	1.3.6.1.4.1.9.9.784.1.3.1.1.31	InetAddressIPv4	read-create	This object specifies the IP address of the secondary DNS server offered to the peer of a target PPP connection. This column is valid only if the 'ipcpDnsSecondary' bit of the corresponding instance of cdtPppValid is '1'.
ADR cdtPppIpcpMask	1.3.6.1.4.1.9.9.784.1.3.1.1.36	InetAddressIPv4	read-create	This object specifies the IP address mask offered to the peer of a target PPP connection. This column is valid only if the 'ipcpMask' bit of the corresponding instance of cdtPppValid is '1'.
INT cdtPppIpcpMaskOption	1.3.6.1.4.1.9.9.784.1.3.1.1.35	INTEGER	read-create	This object specifies the IPCP IP subnet mask option for a target PPP connection: 'other' The implementation of this MIB module does not recognize the configured IP subnet mask option. 'request' The system requests the IP subnet mask from the peer of a target PPP connection. 'reject' The system rejects the IP subnet mask option from the peer of a target PPP connection. This column is valid only if the 'ipcpMaskOption' bit of the corresponding instance of cdtPppValid is '1'.
INT cdtPppIpcpWinsOption	1.3.6.1.4.1.9.9.784.1.3.1.1.32	INTEGER	read-create	This object specifies the IPCP WINS option for a target PPP connection: 'other' The implementation of this MIB module does not recognize the configured WINS option. 'accept' The system accepts any non-zero WINS address from the peer of a target PPP connection. 'request' The system requests the WINS address from the peer of a target PPP connection. 'reject' The system rejects the WINS option from the peer of a target PPP connection. This column is valid only if the 'ipcpWinsOption' bit of the corresponding instance of cdtPppValid is '1'.
ADR cdtPppIpcpWinsPrimary	1.3.6.1.4.1.9.9.784.1.3.1.1.33	InetAddressIPv4	read-create	This object specifies the IP address of the primary WINS server offered to the peer of a target PPP connection. This column is valid only if the 'ipcpWinsPrimary' bit of the corresponding instance of cdtPppValid is '1'.
ADR cdtPppIpcpWinsSecondary	1.3.6.1.4.1.9.9.784.1.3.1.1.34	InetAddressIPv4	read-create	This object specifies the IP address of the secondary WINS server offered to the peer of a target PPP connection. This column is valid only if the 'ipcpWinsSecondary' bit of the corresponding instance of cdtPppValid is '1'.
T/F cdtPppLoopbackIgnore	1.3.6.1.4.1.9.9.784.1.3.1.1.6	TruthValue	read-create	This object specifies whether the system ignores loopback on a target PPP connection. When the system ignores loopback, loopback detection is disabled. This column is valid only if the 'loopbackIgnore' bit of the corresponding instance of cdtPppValid is '1'.
U32 cdtPppMaxBadAuth	1.3.6.1.4.1.9.9.784.1.3.1.1.7	Unsigned32	read-create	This object specifies the number of authentication failures allowed by the system before a target PPP connection is reset. The value '0' cannot be written to an instance of this object. However, it serves as a convenient value when the column is not valid. This column is valid only if the 'maxBadAuth' bit of the corresponding instance of cdtPppValid is '1'.
U32 cdtPppMaxConfigure	1.3.6.1.4.1.9.9.784.1.3.1.1.8	Unsigned32	read-create	This object specifies the number of unacknowledged Configure-Request messages a target PPP connection can send before the system abandons LCP or NCP negotiations. This column is valid only if the 'maxConfigure' bit of the corresponding instance of cdtPppValid is '1'.
U32 cdtPppMaxFailure	1.3.6.1.4.1.9.9.784.1.3.1.1.9	Unsigned32	read-create	This object specifies the number of Configure-Nak messages a target PPP connection can receive before the system abandons LCP or NCP negotiations. This column is valid only if the 'maxFailure' bit of the corresponding instance of cdtPppValid is '1'.
U32 cdtPppMaxTerminate	1.3.6.1.4.1.9.9.784.1.3.1.1.10	Unsigned32	read-create	This object specifies the number of unacknowledged Terminate-Request messages a target PPP connection can send before the system abandons LCP or NCP negotiations. This column is valid only if the 'maxTerminate' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppMsChapV1Hostname	1.3.6.1.4.1.9.9.784.1.3.1.1.17	SnmpAdminString	read-create	This object specifies the hostname sent in a Microsoft CHAP (v1) response on a target PPP connection. If the template does not include this attribute, then the system uses its assigned hostname. This column is valid only if the 'msChapV1Hostname' bit of the corresponding instance of cdtPppValid is '1'.
BIT cdtPppMsChapV1Opts	1.3.6.1.4.1.9.9.784.1.3.1.1.16	Bits	read-create	This object specifies how the system processes version 1 of Microsoft CHAP on a target PPP connection: 'refuse' This option specifies that the system should refuse Microsoft CHAP (v1) requests from peers of a target PPP connection. 'callin' This option specifies that the system should only refuse Microsoft CHAP (v1) requests for incoming calls on a target PPP connection. This option is only relevant if the 'refuse' option is set to '1'. 'wait' This option delays Microsoft CHAP (v1) authentication until after the peer of a target PPP connection has authenticated itself to the system. 'encrypted' This option specifies that the value specified by the corresponding instance of cdtPppMsChapV1Password is already encrypted. This column is valid only if the 'msChapV1Opts' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppMsChapV1Password	1.3.6.1.4.1.9.9.784.1.3.1.1.18	SnmpAdminString	read-create	This object specifies the password used to construct a Microsoft CHAP (v1) response on a target PPP connection. This column is valid only if the 'msChapV1Password' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppMsChapV2Hostname	1.3.6.1.4.1.9.9.784.1.3.1.1.20	SnmpAdminString	read-create	This object specifies the hostname sent in a Microsoft CHAP (v2) response on a target PPP connection. If the template does not include this attribute, then the system uses its assigned hostname. This column is valid only if the 'msChapV2Hostname' bit of the corresponding instance of cdtPppValid is '1'.
BIT cdtPppMsChapV2Opts	1.3.6.1.4.1.9.9.784.1.3.1.1.19	Bits	read-create	This object specifies how the system processes version 2 of Microsoft CHAP on a target PPP connection: 'refuse' This option specifies that the system should refuse Microsoft CHAP (v2) requests from peers of a target PPP connection. 'callin' This option specifies that the system should only refuse Microsoft CHAP (v2) requests for incoming calls on a target PPP connection. This option is only relevant if the 'refuse' option is set to '1'. 'wait' This option delays Microsoft CHAP (v2) authentication until after the peer of a target PPP connection has authenticated itself to the system. 'encrypted' This option specifies that the value specified by the corresponding instance of cdtPppMsChapV2Password is already encrypted. This column is valid only if the 'msChapV2Opts' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppMsChapV2Password	1.3.6.1.4.1.9.9.784.1.3.1.1.21	SnmpAdminString	read-create	This object specifies the password used to construct a Microsoft CHAP (v2) response on a target PPP connection. This column is valid only if the 'msChapV2Password' bit of the corresponding instance of cdtPppValid is '1'.
BIT cdtPppPapOpts	1.3.6.1.4.1.9.9.784.1.3.1.1.22	Bits	read-create	This object specifies how the system processes the PAP on a target PPP connection: 'refuse' This option specifies that the system should refuse PAP requests from peers of a target PPP connection. 'encrypted' This option specifies that the value specified by the corresponding instance of cdtPppPapSentPassword is already encrypted. This column is valid only if the 'papOpts' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppPapPassword	1.3.6.1.4.1.9.9.784.1.3.1.1.24	SnmpAdminString	read-create	This object specifies the username used to construct a PAP response on a target PPP connection. This column is valid only if the 'papPassword' bit of the corresponding instance of cdtPppValid is '1'.
STR cdtPppPapUsername	1.3.6.1.4.1.9.9.784.1.3.1.1.23	SnmpAdminString	read-create	This object specifies the username sent in a PAP response on a target PPP connection. This column is valid only if the 'papUsername' bit of the corresponding instance of cdtPppValid is '1'.
ADR cdtPppPeerDefIpAddr	1.3.6.1.4.1.9.9.784.1.3.1.1.39	InetAddressIPv4	read-create	This object specifies the IP address the system assigns to the peer of a target PPP connection. This column is valid only if the 'peerDefIpAddr' bit of the corresponding instance of cdtPppValid is '1'.
BIT cdtPppPeerDefIpAddrOpts	1.3.6.1.4.1.9.9.784.1.3.1.1.37	Bits	read-create	This object specifies options that affect how the system assigns an IP address to the peer of a target PPP connection: 'ipAddrForced' This option forces the system to assign the next available IP address in the pool to the peer of a target PPP connection. When disabled, the peer may negotiate a specific IP address or the system can assign the peer its previously assigned IP address. 'matchAaaPools' This option specifies that the names of the IP address pools provided by an external AAA server must appear in the corresponding list of IP address pool specified by the cdtPppPeerIpAddrPoolTable. 'backupPools' This option specifies that the corresponding names of the IP address pools specified by the cditPppPeerIpAddrPoolTable serve as backup pools to those provided by an external AAA server. 'staticPools' This option suppresses an attempt to load pools from an external AAA server when the system encounters a missing pool name. This column is valid only if the 'peerIpAddrOpts' bit of the corresponding instance of cdtPppValid is '1'.
INT cdtPppPeerDefIpAddrSrc	1.3.6.1.4.1.9.9.784.1.3.1.1.38	INTEGER	read-create	This object specifies how the system assigns an IP address to the peer of a target PPP connection: 'static' The system assigns the IP address specified by the corresponding instance of cdtPppPeerDefIpAddr. 'pool' The system allocates the first available IP address from the corresponding list of named pools contained by the cdtPppPeerIpAddrPoolTable. 'dhcp' The system acts as a DHCP proxy-client to obtain an IP address. This column is valid only if the 'peerDefIpAddrSrc' bit of the corresponding instance of cdtPppValid is '1'.
cdtPppPeerIpAddrPoolEntry	1.3.6.1.4.1.9.9.784.1.3.2.1		not-accessible	An entry specifies a named pool in a list of pools associated with a PPP template. A PPP template can only have named pools associated with it if it has a cdtPppPeerIpAddrSrc of 'pool'. Any attempt to create an entry for a PPP template that does not have a cdtPppPeerIpAddrSrc of 'pool' must result in a response having an error-status of 'inconsistentValue'. The system automatically creates a corresponding entry when the system associates a named pool with a PPP template through another management entity (e.g., the system's local console). The system automatically destroys an entry under the following circumstances: 1) The system or EMS/NMS destroys the corresponding row in the cdtTemplateTable. 2) The system or EMS/NMS sets the corresponding instance of cdtPppPeerIpAddrSrc with a value other than 'pool'.
STR cdtPppPeerIpAddrPoolName	1.3.6.1.4.1.9.9.784.1.3.2.1.4	SnmpAdminString	read-create	This object specifies the name of the IP address pool associated with the PPP template.
U32 cdtPppPeerIpAddrPoolPriority	1.3.6.1.4.1.9.9.784.1.3.2.1.1	Unsigned32	not-accessible	This object indicates the relative priority of the named pool in the list corresponding to a PPP template. The system searches pools in the order of priority, where lower values represent higher priority.
ROW cdtPppPeerIpAddrPoolStatus	1.3.6.1.4.1.9.9.784.1.3.2.1.2	RowStatus	read-create	This object specifies the status of the entry. The following columns must be valid before activating a subscriber access profile: - cdtPppPeerIpAddrPoolStorage - cdtPppPeerIpAddrPoolName However, these objects specify a default value. Thus, it is possible to use create-and-go semantics without setting any additional columns. An implementation must not allow the EMS/NMS to create an entry if the corresponding instance of cdtPppPeerIpAddrSrc is not 'pool'. An implementation must allow the EMS/NMS to modify any column when this column is 'active'.
STO cdtPppPeerIpAddrPoolStorage	1.3.6.1.4.1.9.9.784.1.3.2.1.3	StorageType	read-create	This object specifies what happens to the name pool entry upon restart. If the corresponding instance of cdtTemplateSrc is not 'local', then this column must be 'volatile'.
cdtPppPeerIpAddrPoolTable	1.3.6.1.4.1.9.9.784.1.3.2		not-accessible	This table contains a prioritized list of named pools for each PPP template. A list corresponding to a PPP template specifies the pools the system searches in an attempt to assign an IP address to the peer of a target PPP connection. The system searches the pools in the order of their priority. This table has an expansion dependent relationship on the cdtPppTemplateTable, containing zero or more rows for each PPP template.
cdtPppTemplateEntry	1.3.6.1.4.1.9.9.784.1.3.1.1		not-accessible	An entry containing attributes relating to PPP connection configuration. The system automatically creates an entry when the system or the EMS/NMS creates a row in the cdtTemplateTable with a cdtTemplateType of one of the following values: 'derived' 'ppp' Likewise, the system automatically destroys an entry when the system or the EMS/NMS destroys the corresponding row in the cdtTemplateTable.
cdtPppTemplateTable	1.3.6.1.4.1.9.9.784.1.3.1		not-accessible	This table contains attributes relating to PPP connection configuration. This table has a sparse-dependent relationship on the cdtTemplateTable, containing a row for each dynamic template having a cdtTemplateType of one of the following values: 'derived' 'ppp'
U32 cdtPppTimeoutAuthentication	1.3.6.1.4.1.9.9.784.1.3.1.1.11	Unsigned32	read-create	This objects specifies the maximum time the system will wait for a response to an authentication request on a target PPP connection. This column is valid only if the 'timeoutAuthentication' bit of the corresponding instance of cdtPppValid is '1'.
U32 cdtPppTimeoutRetry	1.3.6.1.4.1.9.9.784.1.3.1.1.12	Unsigned32	read-create	This objects specifies the maximum time the system will wait for a response to a PPP control packets on a target PPP connection. This column is valid only if the 'timeoutRetry' bit of the corresponding instance of cdtPppValid is '1'.
BIT cdtPppValid	1.3.6.1.4.1.9.9.784.1.3.1.1.1	Bits	read-create	This object specifies which attributes in the dynamic template have been configured to valid values. Each bit in this bit string corresponds to a column in this table. If the bit is '0', then the value of the corresponding column is not valid. If the bit is '1', then the value of the corresponding column has been configured to a valid value. The following list specifies the mappings between bits and the columns: accounting => cdtPppAccounting authentication => cdtPppAuthentication authenticationMethods => cdtPppAuthenticationMethods authorization => cdtPppAuthorization loopbackIgnore => cdtPppLoopbackIgnore maxBadAuth => cdtPppMaxBadAuth maxConfigure => cdtPppMaxConfigure maxFailure => cdtPppMaxFailure maxTerminate => cdtPppMaxTerminate timeoutAuthentication => cdtPppTimeoutAuthentication timeoutRetry => cdtPppTimeoutRetry chapOpts => cdtPppChapOpts chapHostname => cdtPppChapHostname chapPassword => cdtPppChapPassword msChapV1Opts => cdtPppMsChapV1Opts msChapV1Hostname => cdtPppMsChapV1Hostname msChapV1Password => cdtPppMsChapV1Password msChapV2Opts => cdtPppMsChapV2Opts msChapV2Hostname => cdtPppMsChapV2Hostname msChapV2Password => cdtPppMsChapV2Password papOpts => cdtPppPapOpts papSentUsername => cdtPppPapUsername papSentPassword => cdtPppPapPassword eapOpts => cdtPppEapOpts eapIdentity => cdtPppEapIdentity eapPassword => cdtPppEapPassword ipcpAddrOption => cdtPppIpcpAddrOption ipcpDnsOption => cdtPppIpcpDnsOption ipcpDnsPrimary => cdtPppIpcpDnsPrimary ipcpDnsSecondary => cdtPppIpcpDnsSecondary ipcpWinsOption => cdtPppIpcpWinsOption ipcpWinsPrimary => cdtPppIpcpWinsPrimary ipcpWinsSecondary => cdtPppIpcpWinsSecondary ipcpMaskOption => cdtPppIpcpMaskOption ipcpMask => cdtPppIpcpMask peerDefIpAddrOpts => cdtPppPeerOpts peerDefIpAddrSrc => cdtPppPeerDefIpAddrSrc peerDefIpAddr => cdtPppPeerDefIpAddr
cdtService	1.3.6.1.4.1.9.9.784.1.6
cdtSrvGroup	1.3.6.1.4.1.9.9.784.2.2.6			This group contains objects describing attributes contained by service templates.
T/F cdtSrvMulticast	1.3.6.1.4.1.9.9.784.1.6.1.1.6	TruthValue	read-create	This objects specifies whether the system enables multicast service for subscriber sessions of the target service. This column is valid only if the 'sgSrvMcastRoutingIf' bit of the corresponding instance of cdtSrvValid is '1'.
INT cdtSrvNetworkSrv	1.3.6.1.4.1.9.9.784.1.6.1.1.2	INTEGER	read-create	This object specifies the type of network service provided by the target service: 'other' The implementation of this MIB module does not recognize the configured network service. 'none' The target subscriber service does not provide a network service to subscribers sessions. 'local' The target subscriber service provides local termination for subscriber sessions. 'vpdn' The target subscriber service provides a Virtual Private Dialup Network service for subscriber sessions. This column is valid only if the 'networkSrv' bit of the corresponding instance of cdtSrvValid is '1'.
STR cdtSrvSgSrvGroup	1.3.6.1.4.1.9.9.784.1.6.1.1.4	SnmpAdminString	read-create	This object specifies the name of the service group with which the system associates subscriber sessions. A service group specifies a set of services that may be active simultaneously for a given subscriber session. Typically, a service group contains a primary service and one or more secondary services. This column is valid only if the 'sgSrvGroup' bit of the corresponding instance of cdtSrvValid is '1'.
INT cdtSrvSgSrvType	1.3.6.1.4.1.9.9.784.1.6.1.1.5	INTEGER	read-create	This object specifies whether the target service specifies a network-forwarding policy: 'primary' The target service specifies a network-forwarding policy. Primary services are mutually exclusive; that is, only one primary service can be activated for any given subscriber session. 'secondary' The target service has a dependence on the primary service in the group specified by the corresponding instance of cdtSuBSrvSgSrvGroup. After the system activates the primary service, it activates secondary services. When the system deactivates the primary service, then it deactivates all the secondary services in the service group. This column is valid only if the 'sgSrvType' bit of the corresponding instance of cdtSrvValid is '1'.
cdtSrvTemplateEntry	1.3.6.1.4.1.9.9.784.1.6.1.1		not-accessible	An entry containing attributes relating to a service. The system automatically creates entry when the system or the EMS/NMS creates a row in the cdtTemplateTable with a cdtTemplateType of one of the following values: 'derived' 'service' Likewise, the system automatically destroys an entry when the system or the EMS/NMS destroys the corresponding row in the cdtTemplateTable.
cdtSrvTemplateTable	1.3.6.1.4.1.9.9.784.1.6.1		not-accessible	This table contains attributes relating to a service. This table has a sparse-dependent relationship on the cdtTemplateTable, containing a row for each dynamic template having a cdtTemplateType of one of the following values: 'derived' 'service'
BIT cdtSrvValid	1.3.6.1.4.1.9.9.784.1.6.1.1.1	Bits	read-create	This object specifies which attributes in the dynamic template have been configured to valid values. Each bit in this bit string corresponds to a column in this table. If the bit is '0', then the value of the corresponding column is not valid. If the bit is '1', then the value of the corresponding column has been configured to a valid value. The following list specifies the mappings between bits and the columns: networkSrv => cdtSrvNetworkSrv vpdnGroup => cdtSrvVpdnGroup sgSrvGroup => cdtSrvGroup sgSrvType => cdtSrvSgSrvType multicast => cdtSrvMulticast
STR cdtSrvVpdnGroup	1.3.6.1.4.1.9.9.784.1.6.1.1.3	SnmpAdminString	read-create	This object specifies the name of the VPDN group used to configure the network service. This column is valid only if the 'vpdnGroup' bit of the corresponding instance of cdtSrvValid is '1'.
cdtSubscriberGroup	1.3.6.1.4.1.9.9.784.1.7
cdtTemplateAssociationEntry	1.3.6.1.4.1.9.9.784.1.1.3.1		not-accessible	An entry indicates an association of a dynamic template with a target. The system automatically creates an entry when it associates a dynamic template to a target. The system also creates an entry when it derives the configuration that it applies to a target. The system automatically destroys an entry under the following circumstances: 1) The target indicated by the entry no longer exists. 2) The association between the target and the dynamic template no longer exists.
DYN cdtTemplateAssociationName	1.3.6.1.4.1.9.9.784.1.1.3.1.1	DynamicTemplateName	read-only	This object indicates the name of the template associated with the target.
U32 cdtTemplateAssociationPrecedence	1.3.6.1.4.1.9.9.784.1.1.3.1.2	Unsigned32	read-only	This object indicates the relative precedence of the associated dynamic template. Lower values have higher precedence than higher values.
cdtTemplateAssociationTable	1.3.6.1.4.1.9.9.784.1.1.3		not-accessible	This table contains a list of templates associated with each target. This table has an expansion dependent relationship on the cdtTemplateTargetTable, containing zero or more rows for each target.
cdtTemplateCommonEntry	1.3.6.1.4.1.9.9.784.1.1.5.1		not-accessible	An entry containing attributes relating to any target. The system automatically creates an entry when the system or the EMS/NMS creates a row in the cdtTemplateTable with a cdtTemplateType of on the following values: 'derived' 'ppp' 'ethernet' 'ipSubscriber' 'service' Likewise, the system automatically destroys an entry when the system or the EMS/NMS destroys the corresponding row in the cdtTemplateTable.
cdtTemplateCommonTable	1.3.6.1.4.1.9.9.784.1.1.5		not-accessible	This table contains attributes relating to all dynamic templates. Observe that the type of dynamic templates containing these attributes may change with the addition of new dynamic template types. This table has a sparse-dependent relationship on the cdtTemplateTable, containing a row for each dynamic template having a cdtTemplateType of one of the following values: 'derived' 'ppp' 'ethernet' 'ipSubscriber' 'service'
cdtTemplateEntry	1.3.6.1.4.1.9.9.784.1.1.1.1		not-accessible	An entry describes a dynamic template, which serves as a container for configuration attributes. The configuration attributes contained by a dynamic template depends on its type. The system automatically creates a corresponding entry when a dynamic template has been created through another management entity (e.g., the system's local console). Likewise, the system automatically destroys a corresponding entry when a dynamic template has been destroyed through another management entity. The system automatically creates a corresponding entry when an external policy server pushes a user profile or a service profile to the system. The system automatically creates a corresponding entry when it generates a derived configuration.
DYN cdtTemplateName	1.3.6.1.4.1.9.9.784.1.1.1.1.1	DynamicTemplateName	read-only	This object indicates a string-value that uniquely identifies the dynamic template. If the corresponding instance of cdtTemplateSrc is not 'local', then the system automatically generates the name identifying the dynamic template.
INT cdtTemplateSrc	1.3.6.1.4.1.9.9.784.1.1.1.1.5	INTEGER	read-only	This object specifies the source of the dynamic template: 'other' The implementation of the MIB module does not recognize the source of the dynamic template. 'derived' The system created the set of attributes from one or more dynamic templates. 'local' The dynamic template was locally configured through a management entity, such as the local console or a SNMP entity. 'aaaUserProfile' The dynamic template originated from a user profile pushed from an external policy server. 'aaaServiceProfile' The dynamic template originated from a service profile pushed from an external policy server.
ROW cdtTemplateStatus	1.3.6.1.4.1.9.9.784.1.1.1.1.2	RowStatus	read-create	This object specifies the status of the dynamic template. The following columns must be valid before activating a dynamic template: - cdtTemplateStorage - cdtTemplateType However, these objects specify a default value. Thus, it is possible to use create-and-go semantics without setting any additional columns. An implementation must allow the EMS/NMS to modify any column when this column is 'active', including columns defined in tables that have a one-to-one or sparse dependent relationship on this table.
STO cdtTemplateStorage	1.3.6.1.4.1.9.9.784.1.1.1.1.3	StorageType	read-create	This object specifies what happens to the dynamic template upon restart. If the corresponding instance of cdtTemplateSrc is not 'local', then this column must be 'volatile'.
cdtTemplateTable	1.3.6.1.4.1.9.9.784.1.1.1		not-accessible	This table lists the dynamic templates maintained by the system, including those that have been locally-configured on the system and those pushed to the system by external policy servers.
cdtTemplateTargetEntry	1.3.6.1.4.1.9.9.784.1.1.2.1		not-accessible	An entry describes a target associated with one or more dynamic templates. The system automatically creates an entry when it associates a dynamic template to a target. Likewise, the system automatically destroys an entry when a target no longer has any associated dynamic templates.
DYN cdtTemplateTargetId	1.3.6.1.4.1.9.9.784.1.1.2.1.2	DynamicTemplateTargetId	not-accessible	This object uniquely identifies the target within the scope of its type.
ROW cdtTemplateTargetStatus	1.3.6.1.4.1.9.9.784.1.1.2.1.3	RowStatus	read-create	This object specifies the status of the dynamic template target. The following columns must be valid before activating a subscriber access profile: - cdtTemplateTargetStorage However, these objects specify a default value. Thus, it is possible to use create-and-go semantics without setting any additional columns. An implementation must allow the EMS/NMS to modify any column when this column is 'active', including columns defined in tables that have a one-to-one or sparse dependent relationship on this table.
STO cdtTemplateTargetStorage	1.3.6.1.4.1.9.9.784.1.1.2.1.4	StorageType	read-create	This object specifies what happens to the dynamic template target upon restart.
cdtTemplateTargetTable	1.3.6.1.4.1.9.9.784.1.1.2		not-accessible	This table contains a list of targets associated with one or more dynamic templates.
DYN cdtTemplateTargetType	1.3.6.1.4.1.9.9.784.1.1.2.1.1	DynamicTemplateTargetType	not-accessible	This object indicates the type of target.
DYN cdtTemplateType	1.3.6.1.4.1.9.9.784.1.1.1.1.4	DynamicTemplateType	read-create	This object indicates the types of dynamic template.
U32 cdtTemplateUsageCount	1.3.6.1.4.1.9.9.784.1.1.1.1.6	Unsigned32	read-only	This object specifies the number of targets using a dynamic template
cdtTemplateUsageEntry	1.3.6.1.4.1.9.9.784.1.1.4.1		not-accessible	An entry indicates a target using the dynamic template. The system automatically creates an entry when it associates a dynamic template to a target. The system also creates an entry when it derives the configuration that it applies to a target. The system automatically destroys an entry under the following circumstances: 1) The target indicated by the entry no longer exists. 2) The association between the target and the dynamic template no longer exists.
cdtTemplateUsageTable	1.3.6.1.4.1.9.9.784.1.1.4		not-accessible	This table contains a list of targets using each dynamic template. This table has an expansion dependent relationship on the cdtTemplateTable, containing zero or more rows for each dynamic template.
DYN cdtTemplateUsageTargetId	1.3.6.1.4.1.9.9.784.1.1.4.1.2	DynamicTemplateTargetId	read-only	This object indicates the name of the target using the dynamic template
DYN cdtTemplateUsageTargetType	1.3.6.1.4.1.9.9.784.1.1.4.1.1	DynamicTemplateTargetType	read-only	This object indicates the type of target using the dynamic template.
ciscoDynamicTemplateMIB	1.3.6.1.4.1.9.9.784			This MIB defines objects that describe dynamic templates. A dynamic template is a set of configuration attributes that a system can dynamically apply to a target. The target of a dynamic template is the entity configured by the system using the configuration attributes contained by a template. At the time of this writing, an interface represents the only valid target of a dynamic template. However, the architecture does not prevent other target types, and hence, the MIB definition generalizes the notion of a target to allow for this. Generally, the system does not directly apply the attributes contained by a dynamic template to an associated target. The system might generate a derived configuration from the set of dynamic templates associated with the target. A derived configuration represents the union of the configuration attributes contained by each associated dynamic template. In the case of a conflict (i.e., more than one dynamic template specifies the same configuration attribute), the system accepts the configuration attribute from the dynamic template with the highest precedence.
ciscoDynamicTemplateMIBCompliances	1.3.6.1.4.1.9.9.784.2.1
ciscoDynamicTemplateMIBConform	1.3.6.1.4.1.9.9.784.2
ciscoDynamicTemplateMIBGroups	1.3.6.1.4.1.9.9.784.2.2
ciscoDynamicTemplateMIBNotifs	1.3.6.1.4.1.9.9.784.0
ciscoDynamicTemplateMIBObjects	1.3.6.1.4.1.9.9.784.1
ciscoDynamicTemplateR1Compliance	1.3.6.1.4.1.9.9.784.2.1.1			This compliance statement specifies the minimal requirements an implementation must meet in order to claim full compliance with the definition of the CISCO-DYNAMIC-TEMPLATE-MIB.

RFC description

Dynamic configuration templates for Cisco routers allowing centralized application of interface and VRF parameters.

Start monitoring Cisco IOS/IOS-XE router (Broadband Network Gateway/subscriber edge) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-DYNAMIC-TEMPLATE-MIB

What Is CISCO-DYNAMIC-TEMPLATE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description