CISCO-DSL-PROVISION-MIB

All MIBs › CISCO-DSL-PROVISION-MIB

Organization: Cisco Systems, Inc.

Last Updated: 1999-06-18

Category: Cisco Devices, DSL and Broadband

Description: Manages DSL subscriber line provisioning on Cisco platforms, including profile assignment, speed limits, and service activation.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-DSL-PROVISION-MIB?

CISCO-DSL-PROVISION-MIB manages provisioning of Digital Subscriber Line (DSL) subscriber sessions on Cisco broadband aggregation platforms, specifically supporting creation of PPP-over-ATM sessions via Virtual Templates and Network Route Processors (NRPs). It exposes configuration data such as NRP IP address assignments per slot, virtual template numbers and their limits, and the mapping between NRP resources and virtual templates. This is a configuration/provisioning MIB rather than a fault or performance MIB, so its monitoring value lies in verifying that DSL subscriber provisioning resources (NRP slots, virtual templates) are correctly allocated and have not been exhausted, e.g. cdslMaxNrps and cdslMaxVirtualTemplates versus actual usage. It does not show a strong dependency on external standard MIBs beyond general Cisco conventions. It is deployed on Cisco broadband access/aggregation routers terminating large numbers of DSL subscriber PPPoA sessions. Engineers can download the CISCO-DSL-PROVISION-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-DSL-PROVISION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco DSL access/aggregation routers

Monitoring Examples

An administrator would check cdslNrpIpAddressTable/cdslNrpIpAddressEntry keyed by cdslNrpSlotIndex to confirm each NRP slot has a valid cdslNrpIpAddress, and compare cdslVirtualTemplateNumberTable's configured virtual template count against cdslMaxVirtualTemplates to see if the router is approaching its provisioning ceiling. Approaching the cdslMaxNrps limit would signal that new DSL subscriber sessions may soon fail to provision on that chassis.

What Can Be Monitored

NRP IP address assignment per slot
virtual template count vs. maximum
NRP slot allocation
DSL subscriber session provisioning capacity

Imported Objects

From CISCO-SMI

ciscoExperiment

OBJECT-IDENTITY

From IF-MIB

InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
cdslAtmPvc	1.3.6.1.4.1.9.10.30.1.4
U32 cdslAtmPvcAbrIORDF	1.3.6.1.4.1.9.10.30.1.4.2.1.10	Unsigned32	read-only	Abr inverse of rate decrease factor (1/rdf) of this PVC.
U32 cdslAtmPvcAbrIORIF	1.3.6.1.4.1.9.10.30.1.4.2.1.9	Unsigned32	read-only	Abr inverse of rate increase factor (1/rif) of this PVC.
U32 cdslAtmPvcAbrMCR	1.3.6.1.4.1.9.10.30.1.4.2.1.8	Unsigned32	read-only	Abr Minimum Guaranteed Cell Rate(MCR) of this PVC.
U32 cdslAtmPvcAbrPCR	1.3.6.1.4.1.9.10.30.1.4.2.1.7	Unsigned32	read-only	Availabe bit rate (Abr) peak cell rate(PCR) of this PVC.
INT cdslAtmPvcBroadcast	1.3.6.1.4.1.9.10.30.1.4.2.1.11	INTEGER	read-only	This object indicates whether to allow broadcast or not.
STR cdslAtmPvcClass	1.3.6.1.4.1.9.10.30.1.4.2.1.5	DisplayString	read-create	This object indicates the vc-class to inherit when the named vc-class exists. If the object is to set into an empty string, the default value 'default-vc-class' will be used. If the 'default-vc-class' class does exist, it will be created and the encapsulation is set to aal5ciscoppp and the virtual template number is set to the largest virtual template number allowed. If the specified virtual template does not exist, it will be created with no specific configuration. If the specified vc-class does not exist, a new vc-class will be created in the same way as the default-vc-class is. If the specified vc-class exists and its encapsulation is not 'aal5mux' or 'aal5ciscoppp', an error will be returned.
INT cdslAtmPvcEncapsulation	1.3.6.1.4.1.9.10.30.1.4.2.1.12	INTEGER	read-only	This object indicates encapsulation method of this PVC.
cdslAtmPvcEntry	1.3.6.1.4.1.9.10.30.1.4.2.1		not-accessible	The IfIndex by which the table is indexed, is the ATM interface index in which the PVC is created. The only object that is allowed to change the value while the row status is 'active' is cdslAtmPvcClass. Please refer to the description of cdslAtmPvcRowStatus for more information.
INT cdslAtmPvcILMIManage	1.3.6.1.4.1.9.10.30.1.4.2.1.15	INTEGER	read-only	This object indicates whether to ilmi manage or not.
U32 cdslAtmPvcInarp	1.3.6.1.4.1.9.10.30.1.4.2.1.16	Unsigned32	read-only	This object indicates the InARP Frequency in minutes (Only meaningful in aal5snap encapsulation).
INT cdslAtmPvcMuxLinkType	1.3.6.1.4.1.9.10.30.1.4.2.1.13	INTEGER	read-create	This object can be used to This object is used to specify the link type if the encapsulation is aal5mux. 1 -- ip and 2 -- ppp.
STR cdslAtmPvcName	1.3.6.1.4.1.9.10.30.1.4.2.1.3	DisplayString	read-create	This object can be used to identify the PVC. Unique name for each PVC is desired if assigned.
U32 cdslAtmPvcOamPvcLF	1.3.6.1.4.1.9.10.30.1.4.2.1.20	Unsigned32	read-only	This object indicates the OAM loopback frequency(seconds) for this PVC.
INT cdslAtmPvcOamPvcManaged	1.3.6.1.4.1.9.10.30.1.4.2.1.19	INTEGER	read-only	This object indicates whether to enable VC management on OAM in this PVC.
U32 cdslAtmPvcOamRetryDownCount	1.3.6.1.4.1.9.10.30.1.4.2.1.18	Unsigned32	read-only	This object indicates the OAM retry count before declaring a VC is down.
U32 cdslAtmPvcOamRetryUpCount	1.3.6.1.4.1.9.10.30.1.4.2.1.17	Unsigned32	read-only	This object indicates the OAM retry count before declaring a VC is up.
T/F cdslAtmPvcProtocolIpBC	1.3.6.1.4.1.9.10.30.1.4.2.1.21	TruthValue	read-only	Pseudo-broadcast on the protocol IP inarp connections or not (Only meaningful in aal5snap encapsulation).
T/F cdslAtmPvcProtocolIpxBC	1.3.6.1.4.1.9.10.30.1.4.2.1.22	TruthValue	read-only	This object indicates whether to allow Pseudo-broadcast on the protocol IPX inarp connections or not (Only meaningful in aal5snap encapsulation).
INT cdslAtmPvcQosType	1.3.6.1.4.1.9.10.30.1.4.2.1.6	INTEGER	read-only	Quality of Service type of this PVC.
ROW cdslAtmPvcRowStatus	1.3.6.1.4.1.9.10.30.1.4.2.1.28	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table. When the row is created, but the minimun set of parameters is not all set, the status is 'notReady'. There is no PVC corresponding to it. The minimum set of parameters required to activate an entry is cdslAtmPvcSubIfNumber.
I32 cdslAtmPvcSubIfNumber	1.3.6.1.4.1.9.10.30.1.4.2.1.4	Integer32	read-create	This object indicates the ios sub-interface number if this PVC belongs to an atm sub-interface. Once the pvc exists, the value can not be modified. If the PVC is created under the ATM interface level and not a subinterface level, the object shall be zero.
cdslAtmPvcTable	1.3.6.1.4.1.9.10.30.1.4.2		not-accessible	This table includes configuration parameters for ATM PVCs with PPP encapsulation. The vc-mode ATM PVC management approach is used as the PVC creating method, which greatly simplifies configuration by using of vc-class. The PVCs which were created using atm pvc cli commands can only be read or deleted from snmp. In case of reading, only the values of vpi, vci, sub-interface number, encapsulation, virtual template number and row status are meaningful. When trying to set any object of these PVCs, a GEN_ERROR returns except for the row status object. To indicate a PVC is created with old pvc syntax, the value of cdslAtmPvcClass will be set into '!'.
U32 cdslAtmPvcUbrPCR	1.3.6.1.4.1.9.10.30.1.4.2.1.23	Unsigned32	read-only	This object indicates the Ubr Peak Cell Rate.
U32 cdslAtmPvcUbrPlusMCR	1.3.6.1.4.1.9.10.30.1.4.2.1.25	Unsigned32	read-only	This object indicates the Ubr+ Minimum Guaranteed Cell Rate.
U32 cdslAtmPvcUbrPlusPCR	1.3.6.1.4.1.9.10.30.1.4.2.1.24	Unsigned32	read-only	This object indicates the Ubr+ Peak Cell Rate.
U32 cdslAtmPvcVbrNrtPCR	1.3.6.1.4.1.9.10.30.1.4.2.1.26	Unsigned32	read-only	This object indicates the Vbr-Nrt Peak Cell Rate.
U32 cdslAtmPvcVbrNrtSCR	1.3.6.1.4.1.9.10.30.1.4.2.1.27	Unsigned32	read-only	This object indicates the Vbr-Nrt Sustainable Cell Rate.
I32 cdslAtmPvcVci	1.3.6.1.4.1.9.10.30.1.4.2.1.2	Integer32	not-accessible	The virtual channel identifier of the PVC. Please note that it is routing processor's VCI number.
I32 cdslAtmPvcVirtualTemplate	1.3.6.1.4.1.9.10.30.1.4.2.1.14	Integer32	read-create	The virtual template number configured for the PVC.
I32 cdslAtmPvcVpi	1.3.6.1.4.1.9.10.30.1.4.2.1.1	Integer32	not-accessible	The virtual path identifier of the PVC. Please note that it is routing processor's VPI number.
cdslLocalIpAddrPool	1.3.6.1.4.1.9.10.30.1.3
cdslLocalIpAddrPoolEntry	1.3.6.1.4.1.9.10.30.1.3.2.1		not-accessible	This list contains IP pool entry. The entry is read-only. The creation or the deletion of an entry will be a by-product of the entry in the cdslLocalIPAddrRangeTable. When an entry is created and activated in that table, an entry in this table will come into existance if it is not already so. When an entry is deleted in that table, if there is no other entry existing in that table with the same cdslNrpSlotIndex and cdslLocalIpAddrPoolName, the netry in this table with the same indices will diappear from the table.
U32 cdslLocalIpAddrPoolFreeAddresses	1.3.6.1.4.1.9.10.30.1.3.2.1.2	Unsigned32	read-only	The number of IP addresses still available for use in the pool. Please notice that the number is for the whole pool, not for the individual range.
U32 cdslLocalIpAddrPoolInUseAddresses	1.3.6.1.4.1.9.10.30.1.3.2.1.3	Unsigned32	read-only	The number of addresses currently in use in the pool. Please notice that the number is for the whole pool, not for the individual range.
STR cdslLocalIpAddrPoolName	1.3.6.1.4.1.9.10.30.1.3.2.1.1	DisplayString	not-accessible	A unique and non-empty string for the pool. The name can not be modified once created.
cdslLocalIpAddrPoolNumberEntry	1.3.6.1.4.1.9.10.30.1.3.1.1		not-accessible	Entries are read only.
cdslLocalIpAddrPoolNumberTable	1.3.6.1.4.1.9.10.30.1.3.1		not-accessible	This table indicates the number of IP address pools that are presently set up in each NRP.
G32 cdslLocalIpAddrPools	1.3.6.1.4.1.9.10.30.1.3.1.1.2	Gauge32	read-only	The number of local IP address pools presently set up.
cdslLocalIpAddrPoolTable	1.3.6.1.4.1.9.10.30.1.3.2		not-accessible	This table defines the IP local address pool. An IP address pool may have a single entry in the table. The ranges of a pool are represented in the cdslLocalIPAddrRangeTable.
cdslLocalIpAddrRangeEntry	1.3.6.1.4.1.9.10.30.1.3.3.1		not-accessible	This list contains IP pool range entry. User may create a new entry or delete an existing entry. When creating an entry, after its activation, an entry in the cdslLocalIpAddrPoolTable will exist if it is not already so. When destroying an entry, if the range is the only range in the pool, the range entry will be destroyed and the pool entry will disappear from the cdslLocalIpAddrPoolTable.
IP cdslLocalIpAddrRangeHighAddr	1.3.6.1.4.1.9.10.30.1.3.3.1.2	IpAddress	not-accessible	The high range of this IP address pool range. This must be higher than the pool's low range.
IP cdslLocalIpAddrRangeLowAddr	1.3.6.1.4.1.9.10.30.1.3.3.1.1	IpAddress	not-accessible	The low range of this IP address pool range. This must be lower than the pool's high range.
ROW cdslLocalIpAddrRangeRowStatus	1.3.6.1.4.1.9.10.30.1.3.3.1.3	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
cdslLocalIpAddrRangeTable	1.3.6.1.4.1.9.10.30.1.3.3		not-accessible	This table defines the IP local address pool ranges. An IP address pool may have a single entry or multiple entries in the table, since an IP address pool can have multiple dis-continuous ranges. Each range will have a separate entry in the table.
U32 cdslMaxLocalIpAddrPools	1.3.6.1.4.1.9.10.30.1.3.1.1.1	Unsigned32	read-only	Maximum number of local IP address pools allowed in a NRP.
U32 cdslMaxNrps	1.3.6.1.4.1.9.10.30.1.1.1	Unsigned32	read-only	Maximum number of the node routing processors (NRP) allowed in the system.
U32 cdslMaxVcClasses	1.3.6.1.4.1.9.10.30.1.5.1.1.1	Unsigned32	read-only	This object indicates the maximum number of VC classes allowed.
U32 cdslMaxVirtualTemplates	1.3.6.1.4.1.9.10.30.1.2.1.1.1	Unsigned32	read-only	The object specifies the maximum number of virtual templates allowed in one single NRP.
IP cdslNrpIpAddress	1.3.6.1.4.1.9.10.30.1.1.3.1.2	IpAddress	read-only	The object specifies the IP addresses associated with the NRP contained in the slot identified by cdslNrpSlotIndex.
cdslNrpIpAddressEntry	1.3.6.1.4.1.9.10.30.1.1.3.1		not-accessible	These entries are used to store the IP Addresses of NRP cards that are inserted in the indexed slot. The IP addresses are used to access these cards.
cdslNrpIpAddressTable	1.3.6.1.4.1.9.10.30.1.1.3		not-accessible	This table reflects the IP addresses of each NRP in the system.
G32 cdslNrpNumber	1.3.6.1.4.1.9.10.30.1.1.2	Gauge32	read-only	The number of NRPs that are present in this system.
cdslNrpSlot	1.3.6.1.4.1.9.10.30.1.1
I32 cdslNrpSlotIndex	1.3.6.1.4.1.9.10.30.1.1.3.1.1	Integer32	not-accessible	The object specifies the identifier of a slot containing a NRP.
cdslPppOverAtmPvcNumberEntry	1.3.6.1.4.1.9.10.30.1.4.1.1		not-accessible	Each entry represents the responding NRP.
cdslPppOverAtmPvcNumberTable	1.3.6.1.4.1.9.10.30.1.4.1		not-accessible	This table reflects the number of PVCs of PPP encapsulation presently set up in each NRP.
G32 cdslPppOverAtmPvcs	1.3.6.1.4.1.9.10.30.1.4.1.1.1	Gauge32	read-only	The number of atm pvcs that are presently set up with PPP encapsulation. The number of all atm PVCs and the maximum number of PVCs are provided by AToM Mib.
cdslVcClass	1.3.6.1.4.1.9.10.30.1.5
I32 cdslVcClassAbrIORDF	1.3.6.1.4.1.9.10.30.1.5.2.1.7	Integer32	read-create	Abr inverse of rate decrease factor (1/rdf) to the power of two. Note that the actual value is the power of two of this object. For example, value 5 of this object means 2**5 = 32. Range (0..15) to the power of two is the range (1..32768).
I32 cdslVcClassAbrIORIF	1.3.6.1.4.1.9.10.30.1.5.2.1.6	Integer32	read-create	This object specifies Abr inverse of rate increase factor (1/rif) to the power of two. Note that the actual value in the system is the power of two of this object. That is, for example, a value 5 of this object means 2**5 = 32 in the system for AbrIORIF. Range (0..15) to the power of two is the range (1..32768).
I32 cdslVcClassAbrMcr	1.3.6.1.4.1.9.10.30.1.5.2.1.5	Integer32	read-create	This object specifies Minimum Guaranteed Cell Rate. It shall be smaller than cdslVcClassAbrPCR.
I32 cdslVcClassAbrPCR	1.3.6.1.4.1.9.10.30.1.5.2.1.4	Integer32	read-create	This object specifies Abr Peak Cell Rate.
INT cdslVcClassBroadcast	1.3.6.1.4.1.9.10.30.1.5.2.1.8	INTEGER	read-create	This object indicates whether to allow broadcast or not. When set the value, do not use unknown.
INT cdslVcClassEncapsulation	1.3.6.1.4.1.9.10.30.1.5.2.1.9	INTEGER	read-create	This object specifies encapsulation method.
cdslVcClassEntry	1.3.6.1.4.1.9.10.30.1.5.2.1		not-accessible	The VC Class entry is read-create. Each entry represents a VC class.
G32 cdslVcClasses	1.3.6.1.4.1.9.10.30.1.5.1.1.2	Gauge32	read-only	This object indicates the number of VC classes presently set in each NRP identified by cdslNrpSlotIndex.
I32 cdslVcClassIdleMTR	1.3.6.1.4.1.9.10.30.1.5.2.1.13	Integer32	read-create	This object specifies the minimum traffic rate to keep the connection.
I32 cdslVcClassIdleTimeout	1.3.6.1.4.1.9.10.30.1.5.2.1.12	Integer32	read-create	This object specifies idle timeout.
INT cdslVcClassILMIManage	1.3.6.1.4.1.9.10.30.1.5.2.1.14	INTEGER	read-create	This object specifies whether to allow ilmi manage or not. When set the value, do not use unknown.
I32 cdslVcClassInarp	1.3.6.1.4.1.9.10.30.1.5.2.1.15	Integer32	read-create	This object specifies InARP Frequency in minutes.
INT cdslVcClassMuxLinkType	1.3.6.1.4.1.9.10.30.1.5.2.1.10	INTEGER	read-create	This object is used to specify the link type if the encapsulation is aal5mux. 1 for IP and 2 for PPP.
STR cdslVcClassName	1.3.6.1.4.1.9.10.30.1.5.2.1.1	DisplayString	not-accessible	This object is used to identify the vc class.
cdslVcClassNumberEntry	1.3.6.1.4.1.9.10.30.1.5.1.1		not-accessible	Entries are read only.
cdslVcClassNumberTable	1.3.6.1.4.1.9.10.30.1.5.1		not-accessible	This table reflects the number of VC classes that are presently set up in each NRP.
I32 cdslVcClassOamPvcLF	1.3.6.1.4.1.9.10.30.1.5.2.1.19	Integer32	read-create	This object specifies the OAM loopback frequency.
INT cdslVcClassOamPvcManaged	1.3.6.1.4.1.9.10.30.1.5.2.1.18	INTEGER	read-create	This object specifies whether to enable VC management on OAM in a PVC. When set the value, do not use unknown.
I32 cdslVcClassOamRetryDownCount	1.3.6.1.4.1.9.10.30.1.5.2.1.17	Integer32	read-create	OAM retry count before declaring a VC is down
I32 cdslVcClassOamRetryUpCount	1.3.6.1.4.1.9.10.30.1.5.2.1.16	Integer32	read-create	OAM retry count before declaring a VC is up
I32 cdslVcClassOamSvcLF	1.3.6.1.4.1.9.10.30.1.5.2.1.21	Integer32	read-create	This object specifies the OAM loopback frequency for SVC
INT cdslVcClassOamSvcManaged	1.3.6.1.4.1.9.10.30.1.5.2.1.20	INTEGER	read-create	This object specifies whether to enable VC management on OAM on SVC SVC. When set the value, do not use unknown.
T/F cdslVcClassProtocolIpBC	1.3.6.1.4.1.9.10.30.1.5.2.1.22	TruthValue	read-create	This object specifies whether to allow the pseudo-broadcast on the protocol IP inarp connections or not.
T/F cdslVcClassProtocolIpxBC	1.3.6.1.4.1.9.10.30.1.5.2.1.23	TruthValue	read-create	This object specifies whether to allow the pseudo-broadcast on the protocol IPX inarp connections or not.
INT cdslVcClassQosType	1.3.6.1.4.1.9.10.30.1.5.2.1.3	INTEGER	read-create	This object specifies the QOS type of the vc class.
ROW cdslVcClassRowStatus	1.3.6.1.4.1.9.10.30.1.5.2.1.37	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table. The return value of this object is always 'active', if the row exists. To delete the row, set the value to 'destroy'. When creating a new row, 'createAndGo' is the default value and method even if 'createAndWait' is specified. The row and the VC class will be created. When deleting a vc class, if there is still reference to it, it is made invisibile. Otherwise, it is removed physically.
cdslVcClassTable	1.3.6.1.4.1.9.10.30.1.5.2		not-accessible	The entries in this table are vc-classes with at least one parameter configured. In other words, empty classes (with name only) will not be present in this table.
I32 cdslVcClassTransmitPriority	1.3.6.1.4.1.9.10.30.1.5.2.1.24	Integer32	read-create	This object specifies the transmit priority.
INT cdslVcClassType	1.3.6.1.4.1.9.10.30.1.5.2.1.2	INTEGER	read-only	This object indicates the type of the vc class. Atm is for Asynchronous transfer mode and funi for frame user network interface.
I32 cdslVcClassUbrInputPCR	1.3.6.1.4.1.9.10.30.1.5.2.1.26	Integer32	read-create	This object specifies the Ubr Input Peak Cell Rate.
I32 cdslVcClassUbrPCR	1.3.6.1.4.1.9.10.30.1.5.2.1.25	Integer32	read-create	This object specifies the Ubr Peak Cell Rate.
I32 cdslVcClassUbrPlusInputMCR	1.3.6.1.4.1.9.10.30.1.5.2.1.30	Integer32	read-create	This object specifies the Ubr+ Input Minimum Cell Rate. It shall be smaller than cdslVcClassUbrPlusInputPCR.
I32 cdslVcClassUbrPlusInputPCR	1.3.6.1.4.1.9.10.30.1.5.2.1.29	Integer32	read-create	This object specifies the Ubr+ Input Peak Cell Rate.
I32 cdslVcClassUbrPlusMCR	1.3.6.1.4.1.9.10.30.1.5.2.1.28	Integer32	read-create	This object specifies the Ubr+ Minimum Guaranteed Cell Rate. It shall be smaller than cdslVcClassUbrPlusPCR.
I32 cdslVcClassUbrPlusPCR	1.3.6.1.4.1.9.10.30.1.5.2.1.27	Integer32	read-create	This object specifies the Ubr+ Peak Cell Rate.
I32 cdslVcClassVbrNrtInputBP	1.3.6.1.4.1.9.10.30.1.5.2.1.33	Integer32	read-create	This object specifies the Vbr-Nrt Input Burst Parameter: rounded on AIP to the nearest 32, used as is on NPM.
I32 cdslVcClassVbrNrtInputMBS	1.3.6.1.4.1.9.10.30.1.5.2.1.36	Integer32	read-create	This object specifies the Input Maximum Burst Size.
I32 cdslVcClassVbrNrtInputPCR	1.3.6.1.4.1.9.10.30.1.5.2.1.34	Integer32	read-create	This object specifies the Vbr-Nrt Input Peak Cell Rate.
I32 cdslVcClassVbrNrtInputSCR	1.3.6.1.4.1.9.10.30.1.5.2.1.35	Integer32	read-create	This object specifies the Vbr-Nrt Input Sustainable Cell Rate. It shall be smaller than cdslVcClassVbrNrtInputPCR.
I32 cdslVcClassVbrNrtPCR	1.3.6.1.4.1.9.10.30.1.5.2.1.31	Integer32	read-create	This object specifies the Vbr-Nrt Peak Cell Rate.
I32 cdslVcClassVbrNrtSCR	1.3.6.1.4.1.9.10.30.1.5.2.1.32	Integer32	read-create	This object specifies the Vbr-Nrt Sustainable Cell Rate. It shall be smaller than cdslVcClassVbrNrtPCR.
I32 cdslVcClassVirtualTemplate	1.3.6.1.4.1.9.10.30.1.5.2.1.11	Integer32	read-create	The virtual template number. Value zero means not configured.
cdslVirtualTemplate	1.3.6.1.4.1.9.10.30.1.2
cdslVirtualTemplateEntry	1.3.6.1.4.1.9.10.30.1.2.2.1		not-accessible	User may create a new entry or delete an existing entry. Entries may be created without explicitly setting cdslVTRowStatus. While the row status is 'active', objects having read-create access can be changed.
cdslVirtualTemplateNumberEntry	1.3.6.1.4.1.9.10.30.1.2.1.1		not-accessible	Entries are read only.
cdslVirtualTemplateNumberTable	1.3.6.1.4.1.9.10.30.1.2.1		not-accessible	This table reflects the number of virtual template that are presently set up in each NRP. A virtual template interface is a logical entity a configuration for a serial-interface but not tied to a physical interface - thatcan be applied dynamically as needed.
G32 cdslVirtualTemplates	1.3.6.1.4.1.9.10.30.1.2.1.1.2	Gauge32	read-only	This object indicates the number of virtual templates presently set up in each NRP identified by cdslNrpSlotIndex.
cdslVirtualTemplateTable	1.3.6.1.4.1.9.10.30.1.2.2		not-accessible	This table includes the virtual templates in the NRP identified by cNrpSlotIndex. Though a virtual template is often called a virtual template interface, it is not reflected in the ifTable.
I32 cdslVTIndex	1.3.6.1.4.1.9.10.30.1.2.2.1.1	Integer32	not-accessible	This object represents an arbitrary index used to identify the virtual template entry.
IP cdslVTIpAddress	1.3.6.1.4.1.9.10.30.1.2.2.1.3	IpAddress	read-create	This object specifies the IP address associated with this virtual template entry. This object is only valid when cdslVTIpAddressMethod is 'ipAddress'. To set the value correctly, this object shall be set in the same packet as cdslVTIpAddressMethod.
IP cdslVTIpAddressMask	1.3.6.1.4.1.9.10.30.1.2.2.1.4	IpAddress	read-create	This object specifies the IP address mask. This object is only valid when cdslVTIpAddressMethod is 'ipAddress'. To set the value correctly, this object shall be set in the same packet as cdslVTIpAddressMethod.
INT cdslVTIpAddressMethod	1.3.6.1.4.1.9.10.30.1.2.2.1.2	INTEGER	read-create	This object indicates how an IP address is obtained to be associated with this virtual template. The actual parameters of these methods are indicated by the objects defined after. none -- means no IP address associated. ipAddress -- means an explicit IP address and mask. interfaceIp -- uses the IP address of an interface if it has one. negotiate -- obtains IP address from a pre-configured DHCP server. In the set operation, only the parameter corresponding to this object is considered. All other parameters are ignored and forgotten.
NUM cdslVTIpIfIndex	1.3.6.1.4.1.9.10.30.1.2.2.1.5	InterfaceIndexOrZero	read-create	This object specifies the ifIndex of the interface, whose IP address will be used for the virtual template entry. Any interface with an IP address in the routing processor can be selected. This object is only valid when cdslVTIpAddressMethod is 'interfaceIp'. To set the value correctly, this object shall be set in the same packet as cdslVTIpAddressMethod.
INT cdslVTPeerIpAddressMethod	1.3.6.1.4.1.9.10.30.1.2.2.1.6	INTEGER	read-create	This object indicates how an IP address is obtained when a peer requesting one. The actual parameters of these methods are indicated by the objects defined after. none -- means no IP address associated. negotiate -- obtains IP address from a pre-configured DHCP server. ipAddressPool -- obtains IP address from an ip address pool specified by cdslVTPeerIpAddrPool to be defined. In the set operation, only the parameter corresponding to the value of this object is considered. All other parameters are ignored and forgotten.
STR cdslVTPeerIpAddrPool	1.3.6.1.4.1.9.10.30.1.2.2.1.7	DisplayString	read-create	This object is used to specify peer default local IP address pool name. This object is only valid when cdslVTPeerIpAddressMethod is 'ipAddressPool'. To set the value correctly, this object shall be set in the same packet as cdslVTPeerIpAddressMethod. If set this object to a pool name that does not correspond to any entry in the cdslLocalIpAddrPoolTable, then the global IP address mechanism shall be applied. So to use the global IP address mechanism, one should set this object to a non-existent cdslLocalIpAddrPoolName or an empty string.
I32 cdslVTPppAuthChap	1.3.6.1.4.1.9.10.30.1.2.2.1.8	Integer32	read-create	This object is used to specify to use Challenge Handshake Authentication Protocol (CHAP) authentication method and the order it is used. The value zero indicates that CHAP is not used. See the description of object cdslVTPppAuthPap for the meaning of non-zero value.
I32 cdslVTPppAuthMSChap	1.3.6.1.4.1.9.10.30.1.2.2.1.9	Integer32	read-create	This object is used to specify the use of Microsoft's CHAP (MSCHAP) authentication method and the order it is used. The value zero indicates that MSCHAP is not used. See the description of object cdslVTPppAuthPap for the meaning of non-zero value.
I32 cdslVTPppAuthPap	1.3.6.1.4.1.9.10.30.1.2.2.1.10	Integer32	read-create	This object is used to specify whether to use Password Authentication Protocol (PAP) authentication method and the order it is used. This object is one of multiple objects used to specify authentication methods. The other authentication method objects are cdslVTPppAuthChap and cdslVTPppAuthMSChap. A non-zero value for any of these authentication method objects indicates that its associated authentication method is to be employed. The value of these objects indicates the order in which their respective methods should be applied to the process of authenticating users. The lowest non-zero valued authentication method object is used first. If it fails, the second lowest is applied. If all methods fail, the user is rejected. If multiple objects are set to the same value, then the order of the corresponding methods will be adjusted in the order of CHAP, MSCHAP and PAP. Each time one of these auth method value is set, all the auth method object values will be re-assigned to reflect the order change and the values will be in an incremental order started from one. So the return value(s) of a snmpget request for these objects may be different from what they are set. However the order is preserved.
T/F cdslVTPppChapEncrypType	1.3.6.1.4.1.9.10.30.1.2.2.1.13	TruthValue	read-create	This object is used to specify whether to encrypt the PPP CHAP password. Only effective when cdslVTPppChapPassword is non-empty.
STR cdslVTPppChapHost	1.3.6.1.4.1.9.10.30.1.2.2.1.11	DisplayString	read-create	This object is used to specify the PPP CHAP host name.
STR cdslVTPppChapPassword	1.3.6.1.4.1.9.10.30.1.2.2.1.12	DisplayString	read-create	This object is used to specify the PPP CHAP password.
INT cdslVTPppChapRefuse	1.3.6.1.4.1.9.10.30.1.2.2.1.14	INTEGER	read-create	The object is used to refuse CHAP authentication from peers requesting it. To disable this function set the value to no. RefuseCallinOnly indicating the system to refuse to answer CHAP authentication challenges received from the peer, but will still require the peer to answer any CHAP challenges this system sends.
T/F cdslVTPppChapWaitPeer	1.3.6.1.4.1.9.10.30.1.2.2.1.15	TruthValue	read-create	This object is used to specify that the system will not authenticate to a peer requesting CHAP authentication until after the peer has authenticated to this system. To disable this function, set this object to 'false'. That is the system will handle the peer authentication requesting even if a peer has not authenticate itself yet.
T/F cdslVTPppPapEncrypType	1.3.6.1.4.1.9.10.30.1.2.2.1.18	TruthValue	read-create	This object is used to specify whether to encrypt the PAP password. Only effective when cdslVTPppPapPassword is non-empty.
STR cdslVTPppPapPassword	1.3.6.1.4.1.9.10.30.1.2.2.1.17	DisplayString	read-create	This object is used to specify the PPP PAP authentication password. The system only utilizes the user name and password when both cdslVTPppUserName and cdslVTPppPassword are non-empty strings. To enforce this the following mechanism is applied. When both are empty strings, set any single one into non-empty string would automatically set the other into the same string. When set any into empty string, the other object would be set to empty string too automatically.
STR cdslVTPppPapUserName	1.3.6.1.4.1.9.10.30.1.2.2.1.16	DisplayString	read-create	This object is used to specify the PPP PAP user name that will be sent to a peer device. Please refer to the description of cdslVTPppPassword to see the interaction.
INT cdslVTPppUseTacacs	1.3.6.1.4.1.9.10.30.1.2.2.1.19	INTEGER	read-create	This object is used to specify whether to enable TACACS for PPP authentication. SingleLine means yes and plus to accept username and password in the username field that is in single line.
ROW cdslVTRowStatus	1.3.6.1.4.1.9.10.30.1.2.2.1.20	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table.
ciscoDslProvisionMIB	1.3.6.1.4.1.9.10.30			Cisco DSL (Digital Subscriber Line) Provision MIB Module. It is used to create subscriber PPP over ATM sessions and related tasks.
ciscoDslProvMIBBasicCompliance	1.3.6.1.4.1.9.10.30.3.1.1			The compliance statement for entities which implement the Cisco DSL Provision Management MIB.
ciscoDslProvMIBCompliances	1.3.6.1.4.1.9.10.30.3.1
ciscoDslProvMIBConformance	1.3.6.1.4.1.9.10.30.3
ciscoDslProvMIBGroups	1.3.6.1.4.1.9.10.30.3.2
ciscoDslProvMIBNotificationPrefix	1.3.6.1.4.1.9.10.30.2
ciscoDslProvMIBObjects	1.3.6.1.4.1.9.10.30.1
ciscoDslPVCGroup	1.3.6.1.4.1.9.10.30.3.2.4			The DSL Provision PVC Group.
ciscoIpPoolGroup	1.3.6.1.4.1.9.10.30.3.2.3			The DSL Provision IP Pool Group.
ciscoNrpSlotGroup	1.3.6.1.4.1.9.10.30.3.2.1			The DSL Provision NRP Slot Group.
ciscoVcClassGroup	1.3.6.1.4.1.9.10.30.3.2.5			The DSL Provision VC Class Group.
ciscoVirtualTemplateGroup	1.3.6.1.4.1.9.10.30.3.2.2			The DSL Provision Virtual Template Interface Group.

RFC description

Cisco vendor-private MIB for provisioning and managing DSL service parameters and configurations.

Start monitoring Cisco DSL access/aggregation routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-DSL-PROVISION-MIB

What Is CISCO-DSL-PROVISION-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description