All MIBs › CISCO-IDSL-LINE-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2000-01-20
Category: Cisco Devices, DSL and Broadband
Description: Provides management objects for monitoring and configuring IDSL (ISDN-based DSL) line parameters and performance on Cisco DSL equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-IDSL-LINE-MIB?
This is a Cisco enterprise MIB for managing IDSL (ISDN Digital Subscriber Line) interfaces, modeled on the structure of the IETF ADSL-LINE-MIB (RFC 2662) but for Cisco's IDSL line cards. It exposes per-line configuration and alarm profiles (cIdslLineConfProfile, cIdslLineAlarmConfProfile), ITU-C physical inventory data such as serial number, vendor ID, and firmware version (cIdslItucInvSerialNumber, cIdslItucInvVendorId, cIdslItucInvVersionNumber), and line status and performance counters. It is used heavily for monitoring hardware and firmware status of IDSL line units—line status (cIdslItucStatus), performance data over time (cIdslItucPerfDataTable), and inventory/version information—plus it generates SNMP notifications (ciscoIdslLineMIBNotifications) for line alarm conditions. It explicitly parallels and can be used alongside the standard ADSL-LINE-MIB, sharing profile-table conventions, though its tables don't necessarily extend ADSL-LINE-MIB tables directly. It is deployed on Cisco access routers and DSL aggregation equipment providing ISDN-based DSL service to subscribers. Network engineers evaluating or troubleshooting this functionality can download the CISCO-IDSL-LINE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-IDSL-LINE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco IDSL line cards / DSL access equipment
Monitoring Examples
An admin would poll cIdslLineTable/cIdslLineEntry for each line's cIdslLineSpecific and profile assignment, then check cIdslItucStatus and cIdslItucPerfDataTable for error seconds or line-quality degradation. A cIdslItucInvVersionNumber mismatch across line cards could indicate outdated firmware, while a status change combined with a notification from ciscoIdslLineMIBNotifications would flag a line going into alarm.
What Can Be Monitored
- IDSL line status
- line performance/error counters
- line configuration and alarm profiles
- line unit vendor/serial/firmware version
This MIB depends on
Related MIBs
Imported Objects
From ADSL-LINE-MIB
| AdslLineProfileName | |
| adslLineConfProfileName | OBJECT-TYPE |
From CISCO-SMI
| ciscoMgmt | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex | |
| ifIndex | OBJECT-TYPE |
From PerfHist-TC-MIB
| PerfCurrentCount | |
| PerfIntervalCount |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| TEXTUAL-CONVENTION | |
| TruthValue | |
| VariablePointer |
How to Use in IPNetwork Monitor
Example using cIdslItucPerfCVs OID:
Select a Cisco IDSL line cards / DSL access equipment as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cIdslItucPerfCVs into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object specifies the number of coding violations experienced by the ITU-C since agent reset. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| cIdslBasicGroup | 1.3.6.1.4.1.9.9.154.3.2.1 | A collection of managed objects defining the basic operation of an IDSL line. | ||
| NUM cIdslItucIntervalCVs | 1.3.6.1.4.1.9.9.154.1.8.1.3 | PerfIntervalCount | read-only | This object specifies the number of coding violations experienced by the ITU-C in the interval. |
| cIdslItucIntervalEntry | 1.3.6.1.4.1.9.9.154.1.8.1 | not-accessible | A 15-miute interval of physical-layer statistics for a ITU-C class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of idsl(154). | |
| NUM cIdslItucIntervalESs | 1.3.6.1.4.1.9.9.154.1.8.1.4 | PerfIntervalCount | read-only | This object specifies the number of errored seconds experienced by the ITU-C in the interval. |
| NUM cIdslItucIntervalHdlcAborts | 1.3.6.1.4.1.9.9.154.1.8.1.7 | PerfIntervalCount | read-only | This object specifies the number of HDLC aborts experienced by the ITU-C in the interval. |
| NUM cIdslItucIntervalHdlcAligns | 1.3.6.1.4.1.9.9.154.1.8.1.8 | PerfIntervalCount | read-only | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the interval. |
| NUM cIdslItucIntervalHdlcCVs | 1.3.6.1.4.1.9.9.154.1.8.1.6 | PerfIntervalCount | read-only | This object specifies the number of HDLC coding violations experienced by the ITU-C in the interval. |
| NUM cIdslItucIntervalHdlcLongs | 1.3.6.1.4.1.9.9.154.1.8.1.10 | PerfIntervalCount | read-only | This object specifies the number of long HDLC frames received by the ITU-C since agent in the interval. A long HDLC frame contains more than 1500 octets. |
| NUM cIdslItucIntervalHdlcShorts | 1.3.6.1.4.1.9.9.154.1.8.1.9 | PerfIntervalCount | read-only | This object specifies the number of short HDLC frames received by the ITU-C since agent in the interval. A short HDLC frame contains less than 5 octets. |
| INT cIdslItucIntervalNumber | 1.3.6.1.4.1.9.9.154.1.8.1.1 | INTEGER | read-only | The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional. |
| NUM cIdslItucIntervalSESs | 1.3.6.1.4.1.9.9.154.1.8.1.5 | PerfIntervalCount | read-only | This object specifies the number of severely errored seconds experienced by the ITU-C in the interval. |
| cIdslItucIntervalTable | 1.3.6.1.4.1.9.9.154.1.8 | not-accessible | This table contains physical-layer statistics intervals for ITU-C class devices supported by the system. | |
| T/F cIdslItucIntervalValidData | 1.3.6.1.4.1.9.9.154.1.8.1.2 | TruthValue | read-only | This object specifies whether the data for this interval is valid. |
| STR cIdslItucInvSerialNumber | 1.3.6.1.4.1.9.9.154.1.2.1.1 | SnmpAdminString | read-only | This object specifies the vendor specific string that identifies the vendor ITU-C. |
| STR cIdslItucInvVendorId | 1.3.6.1.4.1.9.9.154.1.2.1.2 | SnmpAdminString | read-only | This object specifies the vendor identifier assigned according to ANSI T1.220. |
| STR cIdslItucInvVersionNumber | 1.3.6.1.4.1.9.9.154.1.2.1.3 | SnmpAdminString | read-only | This object specifies the vendor specific version number of the ITU-C. |
| PER cIdslItucPerfCurr15MinCVs | 1.3.6.1.4.1.9.9.154.1.6.1.12 | PerfCurrentCount | read-only | This object specifies the number of coding violations experienced by the ITU-C in the current 15-minute interval. |
| IDS cIdslItucPerfCurr15MinElapsed | 1.3.6.1.4.1.9.9.154.1.6.1.11 | IdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| PER cIdslItucPerfCurr15MinESs | 1.3.6.1.4.1.9.9.154.1.6.1.13 | PerfCurrentCount | read-only | This object specifies the number of errored seconds experienced by the ITU-C in the current 15-minute interval. |
| PER cIdslItucPerfCurr15MinHdlcAborts | 1.3.6.1.4.1.9.9.154.1.6.1.16 | PerfCurrentCount | read-only | This object specifies the number of HDLC aborts experienced by the ITU-C in the current 15-minute interval. |
| PER cIdslItucPerfCurr15MinHdlcAligns | 1.3.6.1.4.1.9.9.154.1.6.1.17 | PerfCurrentCount | read-only | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the current 15-minute interval. |
| PER cIdslItucPerfCurr15MinHdlcCVs | 1.3.6.1.4.1.9.9.154.1.6.1.15 | PerfCurrentCount | read-only | This object specifies the number of HDLC coding violations experienced by the ITU-C in the current 15-minute interval. |
| PER cIdslItucPerfCurr15MinHdlcLongs | 1.3.6.1.4.1.9.9.154.1.6.1.19 | PerfCurrentCount | read-only | This object specifies the number of long HDLC frames received by the ITU-C since agent in the current 15-minute interval. A long HDLC frame contains more than 1500 octets. |
| PER cIdslItucPerfCurr15MinHdlcShorts | 1.3.6.1.4.1.9.9.154.1.6.1.18 | PerfCurrentCount | read-only | This object specifies the number of short HDLC frames received by the ITU-C since agent in the current 15-minute interval. A short HDLC frame contains less than 5 octets. |
| PER cIdslItucPerfCurr15MinSESs | 1.3.6.1.4.1.9.9.154.1.6.1.14 | PerfCurrentCount | read-only | This object specifies the number of severely errored seconds experienced by the ITU-C in the current 15-minute interval. |
| IDS cIdslItucPerfCurr1DayCVs | 1.3.6.1.4.1.9.9.154.1.6.1.21 | IdslPerfCurrDayCount | read-only | This object specifies the number of coding violations experienced by the ITU-C in the current 1-day interval. |
| IDS cIdslItucPerfCurr1DayElapsed | 1.3.6.1.4.1.9.9.154.1.6.1.20 | IdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| IDS cIdslItucPerfCurr1DayESs | 1.3.6.1.4.1.9.9.154.1.6.1.22 | IdslPerfCurrDayCount | read-only | This object specifies the number of errored seconds experienced by the ITU-C in the current 1-day interval. |
| IDS cIdslItucPerfCurr1DayHdlcAborts | 1.3.6.1.4.1.9.9.154.1.6.1.25 | IdslPerfCurrDayCount | read-only | This object specifies the number of HDLC aborts experienced by the ITU-C in the current 1-day interval. |
| IDS cIdslItucPerfCurr1DayHdlcAligns | 1.3.6.1.4.1.9.9.154.1.6.1.26 | IdslPerfCurrDayCount | read-only | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the current 1-day interval. |
| IDS cIdslItucPerfCurr1DayHdlcCVs | 1.3.6.1.4.1.9.9.154.1.6.1.24 | IdslPerfCurrDayCount | read-only | This object specifies the number of HDLC coding violations experienced by the ITU-C in the current 1-day interval. |
| IDS cIdslItucPerfCurr1DayHdlcLongs | 1.3.6.1.4.1.9.9.154.1.6.1.28 | IdslPerfCurrDayCount | read-only | This object specifies the number of long HDLC frames received by the ITU-C since agent in the current 1-day interval. A long HDLC frame contains more than 1500 octets. |
| IDS cIdslItucPerfCurr1DayHdlcShorts | 1.3.6.1.4.1.9.9.154.1.6.1.27 | IdslPerfCurrDayCount | read-only | This object specifies the number of short HDLC frames received by the ITU-C since agent in the current 1-day interval. A short HDLC frame contains less than 5 octets. |
| IDS cIdslItucPerfCurr1DaySESs | 1.3.6.1.4.1.9.9.154.1.6.1.23 | IdslPerfCurrDayCount | read-only | This object specifies the number of severely errored seconds experienced by the ITU-C in the current 1-day interval. |
| C32 cIdslItucPerfCVsEx | 1.3.6.1.4.1.9.9.154.1.6.1.1 | Counter32 | read-only | This object specifies the number of coding violations experienced by the ITU-C since agent reset. |
| cIdslItucPerfDataEntry | 1.3.6.1.4.1.9.9.154.1.6.1 | not-accessible | A set of physical-layer statistics for an ITU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154). | |
| cIdslItucPerfDataTable | 1.3.6.1.4.1.9.9.154.1.6 | not-accessible | This table contains physical-layer statistics for ITU-C class devices supported by the system. | |
| C32 cIdslItucPerfESs | 1.3.6.1.4.1.9.9.154.1.6.1.2 | Counter32 | read-only | This object specifies the number of errored seconds experienced by the ITU-C since agent reset. |
| C32 cIdslItucPerfHdlcAborts | 1.3.6.1.4.1.9.9.154.1.6.1.5 | Counter32 | read-only | This object specifies the number of HDLC aborts experienced by the ITU-C since agent reset. |
| C32 cIdslItucPerfHdlcAligns | 1.3.6.1.4.1.9.9.154.1.6.1.6 | Counter32 | read-only | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets since agent reset. |
| C32 cIdslItucPerfHdlcCVs | 1.3.6.1.4.1.9.9.154.1.6.1.4 | Counter32 | read-only | This object specifies the number of HDLC coding violations experienced by the ITU-C since agent reset. |
| C32 cIdslItucPerfHdlcLongs | 1.3.6.1.4.1.9.9.154.1.6.1.8 | Counter32 | read-only | This object specifies the number of long HDLC frames received by the ITU-C since agent reset. A long HDLC frame contains more than 1500 octets. |
| C32 cIdslItucPerfHdlcShorts | 1.3.6.1.4.1.9.9.154.1.6.1.7 | Counter32 | read-only | This object specifies the number of short HDLC frames received by the ITU-C since agent reset. A short HDLC frame contains less than 5 octets. |
| INT cIdslItucPerfInvalidIntervals | 1.3.6.1.4.1.9.9.154.1.6.1.10 | INTEGER | read-only | The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations). |
| IDS cIdslItucPerfPrev1DayCVs | 1.3.6.1.4.1.9.9.154.1.6.1.30 | IdslPerfPrevDayCount | read-only | This object specifies the number of coding violations experienced by the ITU-C in the previous 1-day interval. |
| IDS cIdslItucPerfPrev1DayESs | 1.3.6.1.4.1.9.9.154.1.6.1.31 | IdslPerfPrevDayCount | read-only | This object specifies the number of errored seconds experienced by the ITU-C in the previous 1-day interval. |
| IDS cIdslItucPerfPrev1DayHdlcAborts | 1.3.6.1.4.1.9.9.154.1.6.1.34 | IdslPerfPrevDayCount | read-only | This object specifies the number of HDLC aborts experienced by the ITU-C in the previous 1-day interval. |
| IDS cIdslItucPerfPrev1DayHdlcAligns | 1.3.6.1.4.1.9.9.154.1.6.1.35 | IdslPerfPrevDayCount | read-only | This object specifies the number of HDLC frames received by the ITU-C with a non-integral number of octets in the previous 1-day interval. |
| IDS cIdslItucPerfPrev1DayHdlcCVs | 1.3.6.1.4.1.9.9.154.1.6.1.33 | IdslPerfPrevDayCount | read-only | This object specifies the number of HDLC coding violations experienced by the ITU-C in the previous 1-day interval. |
| IDS cIdslItucPerfPrev1DayHdlcLongs | 1.3.6.1.4.1.9.9.154.1.6.1.37 | IdslPerfPrevDayCount | read-only | This object specifies the number of long HDLC frames received by the ITU-C since agent in the previous 1-day interval. A long HDLC frame contains more than 1500 octets. |
| IDS cIdslItucPerfPrev1DayHdlcShorts | 1.3.6.1.4.1.9.9.154.1.6.1.36 | IdslPerfPrevDayCount | read-only | This object specifies the number of long HDLC frames received by the ITU-C since agent in the previous 1-day interval. A long HDLC frame contains more than 1500 octets. |
| INT cIdslItucPerfPrev1DayMoniSecs | 1.3.6.1.4.1.9.9.154.1.6.1.29 | INTEGER | read-only | The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason. |
| IDS cIdslItucPerfPrev1DaySESs | 1.3.6.1.4.1.9.9.154.1.6.1.32 | IdslPerfPrevDayCount | read-only | This object specifies the number of severely errored seconds experienced by the ITU-C in the previous 1-day interval. |
| C32 cIdslItucPerfSESs | 1.3.6.1.4.1.9.9.154.1.6.1.3 | Counter32 | read-only | This object specifies the number of severely errored seconds experienced by the ITU-C since agent reset. |
| INT cIdslItucPerfValidIntervals | 1.3.6.1.4.1.9.9.154.1.6.1.9 | INTEGER | read-only | The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available. |
| cIdslItucPhysEntry | 1.3.6.1.4.1.9.9.154.1.2.1 | not-accessible | A set of physical-layer parameters for an ITU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154). | |
| cIdslItucPhysTable | 1.3.6.1.4.1.9.9.154.1.2 | not-accessible | This table contains physical-layer parameters for ITU-C class devices supported by the system. | |
| INT cIdslItucStatus | 1.3.6.1.4.1.9.9.154.1.2.1.4 | INTEGER | read-only | This object specifies the state of the ITU-C transceiver: - loopDown The IDSL link is down, as a result of a near-end has detected a LOS, a LOF, has not exchanged an ACT bit with the downstream BRITE/NT1, or similar fault/condition. - dslSync The IDSL link has achieved physical layer activation with the first downstream entity (iether a BRITE or the NT1). - loopUp The IDSL link has exchanged the ACT bit with the NT1, but LMI signalling is not yet active. This is the normal operating state for PPP operation. - loopUpLmiActive The IDSL link has exchnaged the ACT bit with the NT1 and the LMI signalling is active. This is the normal operating state for frame relay operation. |
| NUM cIdslIturIntervalCVs | 1.3.6.1.4.1.9.9.154.1.9.1.3 | PerfIntervalCount | read-only | This object specifies the number of coding violations experienced by the ITU-R in the interval. |
| cIdslIturIntervalEntry | 1.3.6.1.4.1.9.9.154.1.9.1 | not-accessible | A 15-miute interval of physical-layer statistics for a ITU-R class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of idsl(154). | |
| NUM cIdslIturIntervalESs | 1.3.6.1.4.1.9.9.154.1.9.1.4 | PerfIntervalCount | read-only | This object specifies the number of errored seconds experienced by the ITU-R in the interval. |
| INT cIdslIturIntervalNumber | 1.3.6.1.4.1.9.9.154.1.9.1.1 | INTEGER | read-only | The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional. |
| NUM cIdslIturIntervalSESs | 1.3.6.1.4.1.9.9.154.1.9.1.5 | PerfIntervalCount | read-only | This object specifies the number of severely errored seconds experienced by the ITU-R in the interval. |
| cIdslIturIntervalTable | 1.3.6.1.4.1.9.9.154.1.9 | not-accessible | This table contains physical-layer statistics intervals for ITU-R class devices supported by the system. | |
| T/F cIdslIturIntervalValidData | 1.3.6.1.4.1.9.9.154.1.9.1.2 | TruthValue | read-only | This object specifies whether the data for this interval is valid. |
| PER cIdslIturPerfCurr15MinCVs | 1.3.6.1.4.1.9.9.154.1.7.1.7 | PerfCurrentCount | read-only | This object specifies the number of coding violations experienced by the ITU-R in the current 15-minute interval. |
| IDS cIdslIturPerfCurr15MinElapsed | 1.3.6.1.4.1.9.9.154.1.7.1.6 | IdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| PER cIdslIturPerfCurr15MinESs | 1.3.6.1.4.1.9.9.154.1.7.1.8 | PerfCurrentCount | read-only | This object specifies the number of errored seconds experienced by the ITU-R in the current 15-minute interval. |
| PER cIdslIturPerfCurr15MinSESs | 1.3.6.1.4.1.9.9.154.1.7.1.9 | PerfCurrentCount | read-only | This object specifies the number of severely errored seconds experienced by the ITU-R in the current 15-minute interval. |
| IDS cIdslIturPerfCurr1DayCVs | 1.3.6.1.4.1.9.9.154.1.7.1.11 | IdslPerfCurrDayCount | read-only | This object specifies the number of coding violations experienced by the ITU-R in the current 1-day interval. |
| IDS cIdslIturPerfCurr1DayElapsed | 1.3.6.1.4.1.9.9.154.1.7.1.10 | IdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| IDS cIdslIturPerfCurr1DayESs | 1.3.6.1.4.1.9.9.154.1.7.1.12 | IdslPerfCurrDayCount | read-only | This object specifies the number of errored seconds experienced by the ITU-R in the current 1-day interval. |
| IDS cIdslIturPerfCurr1DaySESs | 1.3.6.1.4.1.9.9.154.1.7.1.13 | IdslPerfCurrDayCount | read-only | This object specifies the number of severely errored seconds experienced by the ITU-R in the current 1-day interval. |
| C32 cIdslIturPerfCVs | 1.3.6.1.4.1.9.9.154.1.7.1.1 | Counter32 | read-only | This object specifies the number of coding violations experienced by the ITU-R since agent reset. |
| cIdslIturPerfDataEntry | 1.3.6.1.4.1.9.9.154.1.7.1 | not-accessible | A set of physical-layer statistics for an ITU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154). | |
| cIdslIturPerfDataTable | 1.3.6.1.4.1.9.9.154.1.7 | not-accessible | This table contains physical-layer statistics for ITU-R class devices supported by the system. | |
| C32 cIdslIturPerfESs | 1.3.6.1.4.1.9.9.154.1.7.1.2 | Counter32 | read-only | This object specifies the number of errored seconds experienced by the ITU-R since agent reset. |
| INT cIdslIturPerfInvalidIntervals | 1.3.6.1.4.1.9.9.154.1.7.1.5 | INTEGER | read-only | The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations). |
| IDS cIdslIturPerfPrev1DayCVs | 1.3.6.1.4.1.9.9.154.1.7.1.15 | IdslPerfPrevDayCount | read-only | This object specifies the number of coding violations experienced by the ITU-R in the previous 1-day interval. |
| IDS cIdslIturPerfPrev1DayESs | 1.3.6.1.4.1.9.9.154.1.7.1.16 | IdslPerfPrevDayCount | read-only | This object specifies the number of errored seconds experienced by the ITU-R in the previous 1-day interval. |
| INT cIdslIturPerfPrev1DayMoniSecs | 1.3.6.1.4.1.9.9.154.1.7.1.14 | INTEGER | read-only | The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason. |
| IDS cIdslIturPerfPrev1DaySESs | 1.3.6.1.4.1.9.9.154.1.7.1.17 | IdslPerfPrevDayCount | read-only | This object specifies the number of severely errored seconds experienced by the ITU-R in the previous 1-day interval. |
| C32 cIdslIturPerfSESs | 1.3.6.1.4.1.9.9.154.1.7.1.3 | Counter32 | read-only | This object specifies the number of severely errored seconds experienced by the ITU-R since agent reset. |
| INT cIdslIturPerfValidIntervals | 1.3.6.1.4.1.9.9.154.1.7.1.4 | INTEGER | read-only | The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available. |
| ADS cIdslLineAlarmConfProfile | 1.3.6.1.4.1.9.9.154.1.1.1.3 | AdslLineProfileName | read-write | This object specifies the row in the adslLineAlarmConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this IDSL line interface. In the case the implementation utilizes 'dynamic mode' (see the ADSL-LINE-MIB for further details), then the value of this object defaults to the name of an alarm configuration profile designated by the implementation as the default alarm configuration profile. In the case the implementation utilizes 'static mode', then the the value of this object is read-only. |
| I32 cIdslLineConfBcDefault | 1.3.6.1.4.1.9.9.154.1.14.1.8 | Integer32 | read-create | This object specifies the default BC (Committed Burst Size) for connections that do not explicitly specify a BC. |
| INT cIdslLineConfLmiNetN392 | 1.3.6.1.4.1.9.9.154.1.14.1.4 | INTEGER | read-create | This object specifies the interval between successive status enquiry messages. |
| INT cIdslLineConfLmiNetN393 | 1.3.6.1.4.1.9.9.154.1.14.1.5 | INTEGER | read-create | This object specifies the value of the network-side error threshold. |
| INT cIdslLineConfLmiNetT392 | 1.3.6.1.4.1.9.9.154.1.14.1.6 | INTEGER | read-create | This object specifies the value of the network-side polling verification timer. |
| INT cIdslLineConfLmiProtocol | 1.3.6.1.4.1.9.9.154.1.14.1.3 | INTEGER | read-create | This object identifies the local inband signaling protocol. |
| ADS cIdslLineConfProfile | 1.3.6.1.4.1.9.9.154.1.1.1.2 | AdslLineProfileName | read-write | This object specifies the row in the adslLineConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this IDSL line interface. In the case the implementation utilizes 'dynamic mode' (see the ADSL-LINE-MIB for further details), then the value of this object defaults to the name of a configuration profile designated by the implementation as the default configuration profile. In the case the implementation utilizes 'static mode', then the the value of this object is read-only. |
| cIdslLineConfProfileEntry | 1.3.6.1.4.1.9.9.154.1.14.1 | not-accessible | A configuration profile containing enterprise-specific IDSL line configuration information. | |
| cIdslLineConfProfileTable | 1.3.6.1.4.1.9.9.154.1.14 | not-accessible | This table extends the adslLineConfProfileTable and contains IDSL line configuration information. | |
| INT cIdslLineConfProtocol | 1.3.6.1.4.1.9.9.154.1.14.1.2 | INTEGER | read-create | This object specifies the layer 2 protocol to be employed by the line, and more specifically the encapsulation type: - frf Specifies the frame relay layer 2 protocol defined by FRF.8. Observe that the encapsulation can be selected per virtual circuit. - pppMuxCisco Specifies the PPP using Cisco proprietary virtual circuit multiplexed encapsulation. - pppMuxIetf Specifies the PPP using virtual circuit multiplexed encapsulation defined by RFC-2364. - pppLlcIetf Specifies the PPP using the LLC (Link Layer Control) encapsulation defined by RFC-2364. |
| INT cIdslLineConfRate | 1.3.6.1.4.1.9.9.154.1.14.1.1 | INTEGER | read-create | This object specifies the desired line rate. |
| INT cIdslLineConfUpcIntent | 1.3.6.1.4.1.9.9.154.1.14.1.7 | INTEGER | read-create | This object specifies the default UPC (Usage Parameter Control) action for connections that do not explicitly specify a UPC action. |
| cIdslLineEntry | 1.3.6.1.4.1.9.9.154.1.1.1 | not-accessible | A set of common attributes describing both ends of an IDSL line supported by the system. There exists an entry for each ifEntry with an ifType of idsl(154). | |
| NUM cIdslLineSpecific | 1.3.6.1.4.1.9.9.154.1.1.1.1 | VariablePointer | read-only | This object specifies an object identifier of an instance of an object in the MIB. The implementation determines the application of this object. For example, an implementation may use this object to provide a reference to the port-class physical entity (see the ENTITY-MIB for further details) corresponding to the IDSL line. |
| cIdslLineTable | 1.3.6.1.4.1.9.9.154.1.1 | not-accessible | This table contains the common attributes describing both ends of IDSL lines supported by the system. | |
| cIdslPM15MinIntervalGroup | 1.3.6.1.4.1.9.9.154.3.2.2 | A collection of managed objects defining performance data collection capability using 15-minute intervals. | ||
| NUM cIdslPppoaIntervalCVs | 1.3.6.1.4.1.9.9.154.1.17.1.4 | PerfIntervalCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the interval. |
| NUM cIdslPppoaIntervalDiscards | 1.3.6.1.4.1.9.9.154.1.17.1.7 | PerfIntervalCount | read-only | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the interval. |
| cIdslPppoaIntervalEntry | 1.3.6.1.4.1.9.9.154.1.17.1 | not-accessible | A 15-minute interval of PPPoA statistics intervals for a ITU-C class device configured for PPP operation. There exists up to 96 entries for each ifEntry that meets the following criteria: 1) The ifEntry has an ifType of idsl(154); 2) The profile associated with the ITU-C class device specifies a value of 'ppp' for the cIdslLineProtocol object. | |
| NUM cIdslPppoaIntervalLongs | 1.3.6.1.4.1.9.9.154.1.17.1.6 | PerfIntervalCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the interval. |
| INT cIdslPppoaIntervalNumber | 1.3.6.1.4.1.9.9.154.1.17.1.1 | INTEGER | read-only | The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional. |
| NUM cIdslPppoaIntervalRTOs | 1.3.6.1.4.1.9.9.154.1.17.1.3 | PerfIntervalCount | read-only | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session in the interval. |
| NUM cIdslPppoaIntervalShorts | 1.3.6.1.4.1.9.9.154.1.17.1.5 | PerfIntervalCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the interval. |
| cIdslPppoaIntervalTable | 1.3.6.1.4.1.9.9.154.1.17 | not-accessible | This table contains PPPoA statistics intervals for those ITU-C class devices configured for PPP operation. | |
| T/F cIdslPppoaIntervalValidData | 1.3.6.1.4.1.9.9.154.1.17.1.2 | TruthValue | read-only | This object specifies whether the data for this interval is valid. |
| cIdslPppoaMapEntry | 1.3.6.1.4.1.9.9.154.1.18.1 | not-accessible | A mapping between a PPP session and an ATM VC. There exists an entry for each ifEntry that meet the following criteria: 1) The ifEntry has an ifType of idsl(154); 2) The profile associated with the ITU-C class device specifies a value of 'ppp' for the cIdslLineProtocol object. | |
| NUM cIdslPppoaMapIfIndex | 1.3.6.1.4.1.9.9.154.1.18.1.1 | InterfaceIndex | read-only | The ifIndex associated with the pseudo-ATM interface onto which the IDSL interface is being mapped. |
| cIdslPppoaMapTable | 1.3.6.1.4.1.9.9.154.1.18 | not-accessible | This table defines the mapping between PPP sessions and ATM VC. | |
| INT cIdslPppoaMapVci | 1.3.6.1.4.1.9.9.154.1.18.1.3 | INTEGER | read-write | The VCI (Virtual Circuit Identifier) associated with the ATM VCL onto which the PPP session is being mapped. |
| INT cIdslPppoaMapVpi | 1.3.6.1.4.1.9.9.154.1.18.1.2 | INTEGER | read-write | The VPI (Virtual Path Identifier) associated with the ATM VCL onto which the PPP session is being mapped. |
| PER cIdslPppoaPerfCurr15MinCVs | 1.3.6.1.4.1.9.9.154.1.16.1.10 | PerfCurrentCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the current 15-minute interval. |
| PER cIdslPppoaPerfCurr15MinDiscards | 1.3.6.1.4.1.9.9.154.1.16.1.13 | PerfCurrentCount | read-only | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the current 15-minute interval. |
| IDS cIdslPppoaPerfCurr15MinElapsed | 1.3.6.1.4.1.9.9.154.1.16.1.8 | IdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| PER cIdslPppoaPerfCurr15MinLongs | 1.3.6.1.4.1.9.9.154.1.16.1.12 | PerfCurrentCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the current 15-minute interval. |
| PER cIdslPppoaPerfCurr15MinRTOs | 1.3.6.1.4.1.9.9.154.1.16.1.9 | PerfCurrentCount | read-only | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session in the current 15-minute interval. |
| PER cIdslPppoaPerfCurr15MinShorts | 1.3.6.1.4.1.9.9.154.1.16.1.11 | PerfCurrentCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the current 15-minute interval. |
| IDS cIdslPppoaPerfCurr1DayCVs | 1.3.6.1.4.1.9.9.154.1.16.1.16 | IdslPerfCurrDayCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the current 1-day interval. |
| IDS cIdslPppoaPerfCurr1DayDiscards | 1.3.6.1.4.1.9.9.154.1.16.1.19 | IdslPerfCurrDayCount | read-only | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the current 1-day interval. |
| IDS cIdslPppoaPerfCurr1DayElapsed | 1.3.6.1.4.1.9.9.154.1.16.1.14 | IdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| IDS cIdslPppoaPerfCurr1DayLongs | 1.3.6.1.4.1.9.9.154.1.16.1.18 | IdslPerfCurrDayCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the current 1-day interval. |
| IDS cIdslPppoaPerfCurr1DayRTOs | 1.3.6.1.4.1.9.9.154.1.16.1.15 | IdslPerfCurrDayCount | read-only | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session in the current 1-day interval. |
| IDS cIdslPppoaPerfCurr1DayShorts | 1.3.6.1.4.1.9.9.154.1.16.1.17 | IdslPerfCurrDayCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the current 1-day interval. |
| C32 cIdslPppoaPerfCVs | 1.3.6.1.4.1.9.9.154.1.16.1.2 | Counter32 | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation since agent reset. |
| cIdslPppoaPerfDataEntry | 1.3.6.1.4.1.9.9.154.1.16.1 | not-accessible | A set of PPPoA statistics for an ITU-C class device configured for PPP operation. There exists an entry for each ifEntry that meet the following criteria: 1) The ifEntry has an ifType of idsl(154); 2) The profile associated with the ITU-C class device specifies a value of 'ppp' for the cIdslLineProtocol object. | |
| cIdslPppoaPerfDataTable | 1.3.6.1.4.1.9.9.154.1.16 | not-accessible | This table contains PPPoA statistics for those ITU-C class devices configured for PPP operation. | |
| C32 cIdslPppoaPerfDiscards | 1.3.6.1.4.1.9.9.154.1.16.1.5 | Counter32 | read-only | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason since agent reset. |
| INT cIdslPppoaPerfInvalidIntervals | 1.3.6.1.4.1.9.9.154.1.16.1.7 | INTEGER | read-only | The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations). |
| C32 cIdslPppoaPerfLongs | 1.3.6.1.4.1.9.9.154.1.16.1.4 | Counter32 | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets since agent reset. |
| IDS cIdslPppoaPerfPrev1DayCVs | 1.3.6.1.4.1.9.9.154.1.16.1.22 | IdslPerfPrevDayCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session exhibiting a coding violation in the previous 1-day interval. |
| IDS cIdslPppoaPerfPrev1DayDiscards | 1.3.6.1.4.1.9.9.154.1.16.1.25 | IdslPerfPrevDayCount | read-only | This object specifies the total number of frames intended for transmission over this PPP session that were discarded for any reason in the previous 1-day interval. |
| IDS cIdslPppoaPerfPrev1DayLongs | 1.3.6.1.4.1.9.9.154.1.16.1.24 | IdslPerfPrevDayCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing more than 1500 octets in the previous 1-day interval. |
| INT cIdslPppoaPerfPrev1DayMoniSecs | 1.3.6.1.4.1.9.9.154.1.16.1.20 | INTEGER | read-only | The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason. |
| IDS cIdslPppoaPerfPrev1DayRTOs | 1.3.6.1.4.1.9.9.154.1.16.1.21 | IdslPerfPrevDayCount | read-only | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session in the previous 1-day interval. |
| IDS cIdslPppoaPerfPrev1DayShorts | 1.3.6.1.4.1.9.9.154.1.16.1.23 | IdslPerfPrevDayCount | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets in the previous 1-day interval. |
| C32 cIdslPppoaPerfRTOs | 1.3.6.1.4.1.9.9.154.1.16.1.1 | Counter32 | read-only | This object specifies the number of frames that could not be completely reassembled due to a reassembly timeout before being transmitted over this PPP session since agent reset. |
| C32 cIdslPppoaPerfShorts | 1.3.6.1.4.1.9.9.154.1.16.1.3 | Counter32 | read-only | This object specifies the number of reassembled frames intended for transmission over this PPP session containing less than 5 octets since agent reset. |
| INT cIdslPppoaPerfValidIntervals | 1.3.6.1.4.1.9.9.154.1.16.1.6 | INTEGER | read-only | The number of previous near-end performance data 15-minute intervals for which data was collected. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available. |
| ciscoIdslLineMIB | 1.3.6.1.4.1.9.9.154 | This MIB module describes IDSL (ISDN Digital Line Subscriber) line interfaces. The structure of this module resembles that of the ADSL-LINE-MIB (RFC-2662). Observe that the tables in this module do not necessarily extend the tables defined by the ADSL-LINE-MIB. Currently, only those tables that contain configuration information extend the profile tables defined by the ADSL-LINE-MIB. This allows the management client to define xDSL configuration profiles that apply across all xDSL modems, independent of the technology being utilized by the modem. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** ADSL - Asymmetric Digital Subscriber Line. ATM - Asynchronous Transfer Mode. BRITE - Basic Rate Interface Terminal Extender. CV - Coding Violation. DLC - Data Link Connection. DSL - Digital Subscriber Line. ES - Error Second. IDSL - IDSN Digital Subscriber Loop. ITU-C - IDSL Transceiver Unit, Central Office end. ITU-R - IDSL Transceiver Unit, Remote terminal end. LMI - Link Management Interface. LOF - Loss Of Frame. LOS - Loss Of Signal. NT - Network Terminator. PPP - Point-to-Point Protocol. PPPoA - PPP over ATM. SES - Severely Errored Second. *** DEFINITIONS *** CODING VIOLATION A coding violation occurs when the incoming signal exhibits a CRC anomaly. DOWNSTREAM The flow of data in the direction from the ITU-C to ITU-R. ERRORED SECOND A second with one or more coding violations. LINE RATE The total data rate supported by a line. Observe that the payload rate is equal the line rate for the earliest implementations of IDSL. However, the payload rate maybe less than the line rate for future implementations. SEVERELY ERRORED SECOND A second with 3 or more coding violations. UPSTREAM The flow of data in the direction from the ATU-R to ATU-C. | ||
| ciscoIdslLineMIBCompliance | 1.3.6.1.4.1.9.9.154.3.1.1 | The compliance statement for entities that implement the CISCO-IDSL-LINE-MIB. Implementation of this MIB is mandatory for any platform that supports one or more IDSL line interfaces. | ||
| ciscoIdslLineMIBCompliances | 1.3.6.1.4.1.9.9.154.3.1 | |||
| ciscoIdslLineMIBConformance | 1.3.6.1.4.1.9.9.154.3 | |||
| ciscoIdslLineMIBGroups | 1.3.6.1.4.1.9.9.154.3.2 | |||
| ciscoIdslLineMIBNotifications | 1.3.6.1.4.1.9.9.154.2.0 | |||
| ciscoIdslLineMIBNotificationsPrefix | 1.3.6.1.4.1.9.9.154.2 | |||
| ciscoIdslLineMIBObjects | 1.3.6.1.4.1.9.9.154.1 |
RFC description
Monitors IDSL (ISDN Digital Subscriber Line) interface performance metrics and line profile configuration.
Start monitoring Cisco IDSL line cards / DSL access equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.