CISCO-DMN-DSG-DR-MIB

All MIBs › CISCO-DMN-DSG-DR-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2014-08-30

Category: Cisco Devices, Satellite

Description: Manages device redundancy configuration and failover for the Cisco DMN D9800 digital satellite gateway platform.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-DMN-DSG-DR-MIB?

CISCO-DMN-DSG-DR-MIB is a Cisco Digital Media Network (DMN) MIB for the D9800 series digital satellite gateway, covering the device redundancy (DR) subsystem used to protect broadcast delivery against equipment failure. It exposes configuration and status data for redundancy behavior, including lock/loss signal timers, verification timers, redundancy profiles, and a table of backup transport paths with their forward-error-correction and enable/wait-flag settings. In monitoring terms it is squarely a fault/redundancy-health MIB: it lets an operator confirm whether backup transport streams are correctly configured and armed to take over, and whether signal-lock/signal-loss timers are tuned appropriately to avoid false failovers or missed outages. It depends on the broader CISCO-DMN-DSG family of MIBs (transport, MoIP, etc.) since the backup paths it configures reference those same signal delivery mechanisms. It is deployed in cable/satellite headend and digital broadcast gateway environments where continuous video/data delivery uptime is critical, making CISCO-DMN-DSG-DR-MIB SNMP monitoring essential for confirming redundancy paths stay armed and ready.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-DMN-DSG-DR-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco DMN D9800 digital satellite gateway

Monitoring Examples

An operator would poll drGlobalCfg alongside sigLockTime and sigLossTime to verify that failover thresholds match the expected signal stability of the primary feed, and walk backupTransportTable/backupTransportEntry (indexed by backupTransportIndex) to confirm each backupTransportSetIdx has a valid backupTransportDvbsFec setting and its backupTransportEwFlag correctly reflects standby readiness. An unexpected change in backupTransportEwFlag without a corresponding signal-loss event would flag a misconfigured or flapping redundancy path. This is used to catch silent failover-readiness problems before an actual outage occurs.

What Can Be Monitored

signal lock timer
signal loss timer
redundancy verify timer
backup transport table entries
backup transport FEC setting
backup transport enable/wait flag

Imported Objects

From CISCO-DMN-DSG-ROOT-MIB

ciscoDSGUtilities

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
ciscoDSGDR	1.3.6.1.4.1.1429.2.2.5.43			Cisco generic DR MIB.
drGlobalCfg	1.3.6.1.4.1.1429.2.2.5.43.1
INT enable	1.3.6.1.4.1.1429.2.2.5.43.1.1	INTEGER	read-write	Disable/Enable Disaster Recovery Feature
INT sigLockTime	1.3.6.1.4.1.1429.2.2.5.43.1.2	INTEGER	read-write	Signal Lock timer (In Seconds)
INT sigLossTime	1.3.6.1.4.1.1429.2.2.5.43.1.3	INTEGER	read-write	Signal Loss timer (In Seconds)
INT verifyTimer	1.3.6.1.4.1.1429.2.2.5.43.1.4	INTEGER	read-write	Verify timer (In Seconds)
INT profile	1.3.6.1.4.1.1429.2.2.5.43.1.5	INTEGER	read-write	Local/Uplink Disaster Recovery Profile
backupTransportTable	1.3.6.1.4.1.1429.2.2.5.43.2		not-accessible	DR BackupTransport Configuration Table.
backupTransportEntry	1.3.6.1.4.1.1429.2.2.5.43.2.1		not-accessible	Entry for Disaster Recovery BackupTransport Configuration.
I32 backupTransportIndex	1.3.6.1.4.1.1429.2.2.5.43.2.1.1	Integer32	read-only	DR CSI record index
I32 backupTransportSetIdx	1.3.6.1.4.1.1429.2.2.5.43.2.1.2	Integer32	read-write	DR CSI Idx.
INT backupTransportDvbsFec	1.3.6.1.4.1.1429.2.2.5.43.2.1.3	INTEGER	read-write	DR DVBS Forward Error Correction: Forward Error Correction Rate. For DVB-S2 modulation only auto is applicable. For DVB-S modulation all options are applicable.
INT backupTransportEwFlag	1.3.6.1.4.1.1429.2.2.5.43.2.1.4	INTEGER	read-write	DR E/W Flag
I32 backupTransportFrequency	1.3.6.1.4.1.1429.2.2.5.43.2.1.5	Integer32	read-write	DR Frequency: The Satellite Downlink frequency in the range of 0 to 15000000 KHz in steps of 1 KHz..
INT backupTransportRFInput	1.3.6.1.4.1.1429.2.2.5.43.2.1.6	INTEGER	read-write	DR Input: Select Input for tuning
INT backupTransportModSys	1.3.6.1.4.1.1429.2.2.5.43.2.1.7	INTEGER	read-write	DR Modulation System.
I32 backupTransportNetId	1.3.6.1.4.1.1429.2.2.5.43.2.1.8	Integer32	read-write	Network Id.
I32 backupTransportOrbitalPos	1.3.6.1.4.1.1429.2.2.5.43.2.1.9	Integer32	read-write	DR Orbital Position
I32 backupTransportOrbpolarization	1.3.6.1.4.1.1429.2.2.5.43.2.1.10	Integer32	read-write	Orbital location Azimuth.The range is from 0 to 3600 in steps of 1. The scaling factor is 1 10th of a degree
I32 backupTransportSymbRate	1.3.6.1.4.1.1429.2.2.5.43.2.1.11	Integer32	read-write	Data rate on the transport stream in millions of symbols per second. Range is from 10000 to 450000 hectoSym/second in steps of 1 hectoSym/second. ( 1 hecto = 10^2 ).
INT backupTransportRollOffFactor	1.3.6.1.4.1.1429.2.2.5.43.2.1.12	INTEGER	read-write	DR Rollof Factor:Alpha filtering - for DVB-S: 0.20/0.35, for DVB-S2: 0.20/0.25/0.35. Roll off with scaling factor of 1/100.
INT backupTransportRowstatus	1.3.6.1.4.1.1429.2.2.5.43.2.1.13	INTEGER	read-write	RowStatus.
backupSetTable	1.3.6.1.4.1.1429.2.2.5.43.3		not-accessible	DR BackupSet Configuration Table.
backupSetEntry	1.3.6.1.4.1.1429.2.2.5.43.3.1		not-accessible	Entry for Disaster Recovery BackupSet Configuration.
I32 backupSetPeid	1.3.6.1.4.1.1429.2.2.5.43.3.1.1	Integer32	read-only	BackupSet PEId
I32 backupSetRecid	1.3.6.1.4.1.1429.2.2.5.43.3.1.2	Integer32	read-only	Backup Set Record Index
I32 backupSetCsiidx	1.3.6.1.4.1.1429.2.2.5.43.3.1.3	Integer32	read-only	CSI Index.
I32 backupSetBkpch	1.3.6.1.4.1.1429.2.2.5.43.3.1.4	Integer32	read-write	Backup Channel.
STR backupSetBkpchDispText	1.3.6.1.4.1.1429.2.2.5.43.3.1.5	DisplayString	read-only	Backup Channel Display Text
INT backupSetRowStatus	1.3.6.1.4.1.1429.2.2.5.43.3.1.6	INTEGER	read-write	Backup Row Status.

RFC description

Implements disaster recovery functionality for Cisco Digital Service Gateway with signal loss detection and failover control.

Start monitoring Cisco DMN D9800 digital satellite gateway with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-DMN-DSG-DR-MIB

What Is CISCO-DMN-DSG-DR-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description