CISCO-CLASS-BASED-QOS-MIB

All MIBs › CISCO-CLASS-BASED-QOS-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2009-04-24

Category: Cisco Devices, Network Interfaces, Quality of Service

Description: Provides read access to Quality of Service (QoS) configuration and statistics for Cisco platforms that support the Modular QoS Command-Line Interface (MQC).

IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring CISCO-CLASS-BASED-QOS-MIB with a free 30-day trial of IPNetwork Monitor.

What Is CISCO-CLASS-BASED-QOS-MIB?

CISCO-CLASS-BASED-QOS-MIB is a Cisco IOS/IOS-XE MIB that exposes the configuration and runtime statistics of Modular QoS CLI (MQC) based Quality of Service policies. It covers general categories of data such as class-map and policy-map definitions, queueing and policing configuration, and per-class packet/byte counters and drop statistics. While primarily a performance and configuration MIB rather than a hardware-health MIB, it is heavily used to monitor the operational status of QoS software features on a device, including queue depths, discard counts, and whether a configured service policy is actively attached and functioning as expected. It complements the interface-level data in IF-MIB and is typically deployed alongside it since QoS policies are attached to specific interfaces. Typical deployment is on Cisco routers and switches carrying converged voice, video, and data traffic, where administrators rely on the CISCO-CLASS-BASED-QOS-MIB to verify that traffic-shaping and prioritization policies are behaving correctly under load.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-CLASS-BASED-QOS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco routers
Cisco switches

Monitoring Examples

An administrator would poll cbQosServicePolicyTable to find which policy maps are attached to which interfaces, then walk cbQosQueueingClassCfgTable/cbQosQueueingClassCfgEntry to check cbQosQueueingClassCfgQLimitWeight and cbQosQueueingClassCfgThreshold against actual queue occupancy. A rising drop counter alongside cbQosQlimitWeightValue at its configured limit would reveal that a class-based queue is congested and dropping packets, indicating the need to re-tune bandwidth allocation. cbQosMeasureIPSLACfgTable can also be polled to correlate configured IP SLA measurement groups with observed QoS performance.

What Can Be Monitored

QoS policy-map attachment
class-map queue limits
queue threshold and drop counts
IP SLA measurement group configuration
per-class packet/byte statistics

Imported Objects

From CISCO-FRAME-RELAY-MIB

DlciNumber

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From CISCO-TC

EntPhysicalIndexOrZero
Unsigned64

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From Q-BRIDGE-MIB

VlanIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
cbQosAFPoliceCfgGroup	1.3.6.1.4.1.9.9.166.2.2.26			Optional objects to provide CB QoS objects configuration information.
cbQosAFPoliceStatsGroup	1.3.6.1.4.1.9.9.166.2.2.25			Optional objects to provide CB QoS objects configuration information.
cbQosAFPoliceViolateCfgGroup	1.3.6.1.4.1.9.9.166.2.2.34			Optional objects to provide CB QoS objects configuration information.
U32 cbQosATMPolicyIndex	1.3.6.1.4.1.9.9.166.1.4.1.1.1	Unsigned32	read-only	An arbitrary (system-assigned) index for all Service Policies. This is identical to cbQosPolicyIndex.
cbQosATMPVCPolicy	1.3.6.1.4.1.9.9.166.1.4
cbQosATMPVCPolicyEntry	1.3.6.1.4.1.9.9.166.1.4.1.1		not-accessible	Using ifIndex, VPI, VCI, and Direction, each unique index combination translates to a service policy that is attached to a ATM VC, for particular traffic direction.
cbQosATMPVCPolicyGroup	1.3.6.1.4.1.9.9.166.2.2.4			Required objects to provide CB QoS objects configuration information.
cbQosATMPVCPolicyTable	1.3.6.1.4.1.9.9.166.1.4.1		not-accessible	This table describes the policies that are attached to a ATM PVC.
U32 cbQosAtmVCI	1.3.6.1.4.1.9.9.166.1.1.1.1.7	Unsigned32	read-only	VCI for the ATMVC to which this service is attached. This field only make sense if the service policy is attached to a ATM VC.
U32 cbQosAtmVPI	1.3.6.1.4.1.9.9.166.1.1.1.1.6	Unsigned32	read-only	VPI for the ATMVC to which this service is attached. This field only make sense if the service policy is attached to a ATM VC.
cbQosC3plAccountCfg	1.3.6.1.4.1.9.9.166.1.33
cbQosC3plAccountCfgEntry	1.3.6.1.4.1.9.9.166.1.33.1.1		not-accessible	Each entry in this table describes configuration information about a c3pl account action. The information includes: feature type. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex of each C3pl Account Action.
cbQosC3plAccountCfgGroup	1.3.6.1.4.1.9.9.166.2.2.71			Required objects to provide c3pl account action configuration information (provide drop types) .
cbQosC3plAccountCfgTable	1.3.6.1.4.1.9.9.166.1.33.1		not-accessible	This table specifies C3pl Account Action configuration information
C32 cbQosC3plAccountDropByte	1.3.6.1.4.1.9.9.166.1.34.1.1.5	Counter32	read-only	The lower 32 bits count of bytes dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C64 cbQosC3plAccountDropByte64	1.3.6.1.4.1.9.9.166.1.34.1.1.6	Counter64	read-only	The 64 bits count of bytes dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosC3plAccountDropByteOverflow	1.3.6.1.4.1.9.9.166.1.34.1.1.4	Counter32	read-only	The upper 32 bits count of bytes dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosC3plAccountDropPkt	1.3.6.1.4.1.9.9.166.1.34.1.1.2	Counter32	read-only	The lower 32 bits count of packets dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C64 cbQosC3plAccountDropPkt64	1.3.6.1.4.1.9.9.166.1.34.1.1.3	Counter64	read-only	The 64 bits count of packets dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosC3plAccountDropPktOverflow	1.3.6.1.4.1.9.9.166.1.34.1.1.1	Counter32	read-only	The upper 32 bits count of packets dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
SET cbQosC3plAccountFeatureType	1.3.6.1.4.1.9.9.166.1.33.1.1.1	SetC3plAccountFeatureType	read-only	The feature type is used to indicated different drop statistics.
cbQosC3plAccountStats	1.3.6.1.4.1.9.9.166.1.34
cbQosC3plAccountStatsEntry	1.3.6.1.4.1.9.9.166.1.34.1.1		not-accessible	Each entry in this table describes the statistical information about C3pl Account Action. Account action specific information you can find in this table are : queueing drop pkt/byte counters, wred drop pkt/byte counters, police pkt/byte counters. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, such as cbQosPolicyIndex, cbQosObjectsIndex, and cbQosC3plAccountFeatureType.
cbQosC3plAccountStatsGroup	1.3.6.1.4.1.9.9.166.2.2.72			Optional objects to provide c3pl account action statistics information.
cbQosC3plAccountStatsTable	1.3.6.1.4.1.9.9.166.1.34.1		not-accessible	This table specifies C3pl Account Action related statistics information.
C32 cbQosC3plAccountTailDropByte	1.3.6.1.4.1.9.9.166.1.34.1.1.11	Counter32	read-only	The lower 32 bits count of bytes dropped when the number of packets in the associated queue was greater than the maximum threshold.
C64 cbQosC3plAccountTailDropByte64	1.3.6.1.4.1.9.9.166.1.34.1.1.12	Counter64	read-only	The 64 bits count of bytes dropped when the number of packets in the associated queue was greater than the maximum threshold.
C32 cbQosC3plAccountTailDropByteOverflow	1.3.6.1.4.1.9.9.166.1.34.1.1.10	Counter32	read-only	The upper 32 bits count of bytes dropped when the number of packets in the associated queue was greater than the maximum threshold.
C32 cbQosC3plAccountTailDropPkt	1.3.6.1.4.1.9.9.166.1.34.1.1.8	Counter32	read-only	The lower 32 bits count of packets dropped when the number of packets in the associated queue was greater than the maximum threshold.
C64 cbQosC3plAccountTailDropPkt64	1.3.6.1.4.1.9.9.166.1.34.1.1.9	Counter64	read-only	The 64 bits count of packets dropped when the number of packets in the associated queue was greater than the maximum threshold.
C32 cbQosC3plAccountTailDropPktOverflow	1.3.6.1.4.1.9.9.166.1.34.1.1.7	Counter32	read-only	The upper 32 bits count of packets dropped when the number of packets in the associated queue was greater than the maximum threshold.
cbQosClassMapCfg	1.3.6.1.4.1.9.9.166.1.7
cbQosClassMapCfgGroup	1.3.6.1.4.1.9.9.166.2.2.7			Required objects to provide CB QoS objects configuration information.
cbQosClassMapStats	1.3.6.1.4.1.9.9.166.1.15
cbQosClassMapStatsGroup	1.3.6.1.4.1.9.9.166.2.2.15			Required objects to provide CB QoS objects configuration information.
cbQosCMCfgEntry	1.3.6.1.4.1.9.9.166.1.7.1.1		not-accessible	Each entry in this table describes configuration information about a classmap. The information includes: Name, and it's description and whether it is a Match-All or Match-Any class. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex of each ClassMap.
cbQosCMCfgTable	1.3.6.1.4.1.9.9.166.1.7.1		not-accessible	This table specifies ClassMap configuration information
STR cbQosCMDesc	1.3.6.1.4.1.9.9.166.1.7.1.1.2	DisplayString	read-only	Description of the Classmap.
G32 cbQosCMDropBitRate	1.3.6.1.4.1.9.9.166.1.15.1.1.18	Gauge32	read-only	The bit rate of the drops per class as the result of all features that can produce drops (e.g., police, random detect, etc.).
C32 cbQosCMDropByte	1.3.6.1.4.1.9.9.166.1.15.1.1.16	Counter32	read-only	The lower 32 bits counter of dropped bytes per class as the result of all features that can produce drops (e.g., police, random detect, etc.).
C64 cbQosCMDropByte64	1.3.6.1.4.1.9.9.166.1.15.1.1.17	Counter64	read-only	The 64 bits counter of dropped bytes per class as the result of all features that can produce drops (e.g., police, random detect, etc.).
C32 cbQosCMDropByteOverflow	1.3.6.1.4.1.9.9.166.1.15.1.1.15	Counter32	read-only	The upper 32 bits counter of dropped bytes per class as the result of all features that can produce drops (e.g., police, random detect, etc.).
C32 cbQosCMDropPkt	1.3.6.1.4.1.9.9.166.1.15.1.1.13	Counter32	read-only	The lower 32 bits counter of dropped pkts per class as the result of all features that can produce drops (e.g., police, random detect, etc.).
C64 cbQosCMDropPkt64	1.3.6.1.4.1.9.9.166.1.15.1.1.14	Counter64	read-only	The 64 bits counter of dropped pkts per class as the result of all features that can produce drops (e.g., police, random detect, etc.).
C32 cbQosCMDropPktOverflow	1.3.6.1.4.1.9.9.166.1.15.1.1.12	Counter32	read-only	The upper 32 bits counter of dropped pkts per class as the result of all features that can produce drops (e.g., police, random detect, etc.).
QOS cbQosCMInfo	1.3.6.1.4.1.9.9.166.1.7.1.1.3	QosClassInfo	read-only	Match all vs Match any in a given class.
STR cbQosCMName	1.3.6.1.4.1.9.9.166.1.7.1.1.1	DisplayString	read-only	Name of the Classmap.
C32 cbQosCMNoBufDropPkt	1.3.6.1.4.1.9.9.166.1.15.1.1.20	Counter32	read-only	The lower 32 bits drop packet count which occured due to a lack of SRAM buffers during output processing on an interface.
C64 cbQosCMNoBufDropPkt64	1.3.6.1.4.1.9.9.166.1.15.1.1.21	Counter64	read-only	The 64 bits drop packet count which occured due to a lack of SRAM buffers during output processing on an interface.
C32 cbQosCMNoBufDropPktOverflow	1.3.6.1.4.1.9.9.166.1.15.1.1.19	Counter32	read-only	The upper 32 bits drop packet count which occured due to a lack of SRAM buffers during output processing on an interface.
G32 cbQosCMPostPolicyBitRate	1.3.6.1.4.1.9.9.166.1.15.1.1.11	Gauge32	read-only	The bit rate of the traffic after executing QoS policies.
C32 cbQosCMPostPolicyByte	1.3.6.1.4.1.9.9.166.1.15.1.1.9	Counter32	read-only	The lower 32 bits count of outbound octets after executing QoS policies.
C64 cbQosCMPostPolicyByte64	1.3.6.1.4.1.9.9.166.1.15.1.1.10	Counter64	read-only	The 64 bits count of outbound octets after executing QoS policies.
C32 cbQosCMPostPolicyByteOverflow	1.3.6.1.4.1.9.9.166.1.15.1.1.8	Counter32	read-only	The upper 32 bits count of outbound octets after executing QoS policies.
G32 cbQosCMPrePolicyBitRate	1.3.6.1.4.1.9.9.166.1.15.1.1.7	Gauge32	read-only	The bit rate of the traffic prior to executing any QoS policies.
C32 cbQosCMPrePolicyByte	1.3.6.1.4.1.9.9.166.1.15.1.1.5	Counter32	read-only	The lower 32 bits count of inbound octets prior to executing any QoS policies.
C64 cbQosCMPrePolicyByte64	1.3.6.1.4.1.9.9.166.1.15.1.1.6	Counter64	read-only	The 64 bits count of inbound octets prior to executing any QoS policies.
C32 cbQosCMPrePolicyByteOverflow	1.3.6.1.4.1.9.9.166.1.15.1.1.4	Counter32	read-only	The upper 32 bits count of inbound octets prior to executing any QoS policies.
C32 cbQosCMPrePolicyPkt	1.3.6.1.4.1.9.9.166.1.15.1.1.2	Counter32	read-only	The lower 32 bits count of inbound packets prior to executing any QoS policies.
C64 cbQosCMPrePolicyPkt64	1.3.6.1.4.1.9.9.166.1.15.1.1.3	Counter64	read-only	The 64 bits count of inbound packets prior to executing any QoS policies.
C32 cbQosCMPrePolicyPktOverflow	1.3.6.1.4.1.9.9.166.1.15.1.1.1	Counter32	read-only	The upper 32 bits count of inbound packets prior to executing any QoS policies.
cbQosCMStatsEntry	1.3.6.1.4.1.9.9.166.1.15.1.1		not-accessible	Each entry in this table describes the statistical information about ClassMap. ClassMap specific information you can find in this table are : pre/post policy pkt/byte counts, bit rates, drop pkt/bytes and no buffer drops. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, such as cbQosPolicyIndex and cbQosObjectsIndex.
cbQosCMStatsTable	1.3.6.1.4.1.9.9.166.1.15.1		not-accessible	This table specifies ClassMap related Statistical information.
U32 cbQosConfigIndex	1.3.6.1.4.1.9.9.166.1.5.1.1.2	Unsigned32	read-only	An arbitrary (system-assigned) config (instance independent) index for each Object. Each objects having the same configuration share the same config index.
cbQosEBCfg	1.3.6.1.4.1.9.9.166.1.29
U32 cbQosEBCfgDelayTarget	1.3.6.1.4.1.9.9.166.1.29.1.1.3	Unsigned32	read-only	One-in-Number target indicating that no more than one packet in (this) number will exceed the delay threshold specified by cbQosEBCfgDelayThreshold.
U32 cbQosEBCfgDelayThreshold	1.3.6.1.4.1.9.9.166.1.29.1.1.4	Unsigned32	read-only	The time in milliseconds for the delay threshold.
U32 cbQosEBCfgDropTarget	1.3.6.1.4.1.9.9.166.1.29.1.1.2	Unsigned32	read-only	One-in-Number target indicating that no more than one packet in (this) number will be dropped.
cbQosEBCfgEntry	1.3.6.1.4.1.9.9.166.1.29.1.1		not-accessible	Each entry in this table describes configuration information about Estimate Bandwidth. It includes: drop target, delay target and delay threshold. This table contains configuration information only. It is indexed by the cbQosConfigIndex.
cbQosEBCfgGroup	1.3.6.1.4.1.9.9.166.2.2.61			Optional objects to provide Estimate Bandwidth configuration information.
CBQ cbQosEBCfgMechanism	1.3.6.1.4.1.9.9.166.1.29.1.1.1	CbQosEBType	read-only	Bandwidth estimate algorithm type.
cbQosEBCfgTable	1.3.6.1.4.1.9.9.166.1.29.1		not-accessible	This table specifies Estimate Bandwidth related configuration information.
cbQosEBStats	1.3.6.1.4.1.9.9.166.1.30
CBQ cbQosEBStatsCorvilCTD	1.3.6.1.4.1.9.9.166.1.30.1.1.3	CbQosEBCtd	read-only	The Corvil CTD value defined by CbQosEBCtd.
T/F cbQosEBStatsCorvilEBStatus	1.3.6.1.4.1.9.9.166.1.30.1.1.2	TruthValue	read-only	Boolean to indicate if Corvil EB is ready. true - Bandwidth estimate is available. false - Bandwidth estimate is not available.
G32 cbQosEBStatsCorvilEBValue	1.3.6.1.4.1.9.9.166.1.30.1.1.1	Gauge32	read-only	The current Corvil EB bandwidth value.
cbQosEBStatsEntry	1.3.6.1.4.1.9.9.166.1.30.1.1		not-accessible	Each entry in this table describes Estimate Bandwidth related statistical information.
cbQosEBStatsGroup	1.3.6.1.4.1.9.9.166.2.2.62			Optional objects to provide Estimate Bandwidth status information.
cbQosEBStatsTable	1.3.6.1.4.1.9.9.166.1.30.1		not-accessible	This table specifies Estimate Bandwidth related statistical information.
ENT cbQosEntityIndex	1.3.6.1.4.1.9.9.166.1.1.1.1.8	EntPhysicalIndexOrZero	read-only	In cases where the policy is attached to an entity e.g. control-plane, this object represents the entity physical index of the entity to which the policy has been attached. A value zero may be returned if the policy is not attached to a physical entity or the entPhysicalTable is not supported on the SNMP agent.
cbQosFrameRelayPolicyEntry	1.3.6.1.4.1.9.9.166.1.3.1.1		not-accessible	Using ifIndex, FR DLCI, and Direction, each unique index combination translates to a service policy that is attached to a FR DLCI, for particular traffic direction.
cbQosFrameRelayPolicyTable	1.3.6.1.4.1.9.9.166.1.3.1		not-accessible	This table describes the service polices that are attached to Frame Relay DLCIs.
cbQosFrameRelayVCPolicy	1.3.6.1.4.1.9.9.166.1.3
cbQosFrameRelayVCPolicyGroup	1.3.6.1.4.1.9.9.166.2.2.3			Required objects to provide CB QoS objects configuration information.
DLC cbQosFrDLCI	1.3.6.1.4.1.9.9.166.1.1.1.1.5	DlciNumber	read-only	DLCI for the FRVC to which this service is attached. This field only make sense if the service policy is attached to a Frame Relay DLCI.
U32 cbQosFRPolicyIndex	1.3.6.1.4.1.9.9.166.1.3.1.1.1	Unsigned32	read-only	An arbitrary (system-assigned) index for all Service Policies. This is identical to cbQosPolicyIndex.
NUM cbQosIfIndex	1.3.6.1.4.1.9.9.166.1.1.1.1.4	InterfaceIndex	read-only	ifIndex for the interface to which this service is attached. This field makes sense only if the logical interface has a snmp ifIndex. For e.g. the value of this field is meaningless when the cbQosIfType is controlPlane.
U32 cbQosIFPolicyIndex	1.3.6.1.4.1.9.9.166.1.2.1.1.1	Unsigned32	read-only	An arbitrary (system-assigned) index for all Service Policies. This is identical to cbQosPolicyIndex.
NUM cbQosIfType	1.3.6.1.4.1.9.9.166.1.1.1.1.2	InterfaceType	read-only	This describes the logical interface/media type to which this service policy is attached.
cbQosInterfacePolicy	1.3.6.1.4.1.9.9.166.1.2
cbQosInterfacePolicyEntry	1.3.6.1.4.1.9.9.166.1.2.1.1		not-accessible	Using ifIndex and Direction, each unique index pair translates to a service policy that is attached to a main/sub interface, for particular traffic direction.
cbQosInterfacePolicyGroup	1.3.6.1.4.1.9.9.166.2.2.2			Required objects to provide CB QoS objects configuration information.
cbQosInterfacePolicyTable	1.3.6.1.4.1.9.9.166.1.2.1		not-accessible	This table describes the service polices that are attached to main and sub interfaces.
cbQosIPHCCfg	1.3.6.1.4.1.9.9.166.1.22
cbQosIPHCCfgEntry	1.3.6.1.4.1.9.9.166.1.22.1.1		not-accessible	Each entry in this table describes configuration information about IP Header compression. This includes the compression option of UDP/RTP header, TCP header or both. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by cbQosConfigIndex.
cbQosIPHCCfgGroup	1.3.6.1.4.1.9.9.166.2.2.46			Optional object to provide CB QoS IP header compression configuration information.
IPH cbQosIPHCCfgOption	1.3.6.1.4.1.9.9.166.1.22.1.1.1	IPHCOption	read-only	The configured IP header compression option. The value is defined by IPHCOption.
cbQosIPHCCfgTable	1.3.6.1.4.1.9.9.166.1.22.1		not-accessible	This table specifies IP Header Compression configuration information.
C32 cbQosIPHCRtpCmprsOutPkt	1.3.6.1.4.1.9.9.166.1.23.1.1.5	Counter32	read-only	The lower 32 bits count of outbound compressed UDP/RTP packets.
C64 cbQosIPHCRtpCmprsOutPkt64	1.3.6.1.4.1.9.9.166.1.23.1.1.6	Counter64	read-only	The 64 bits count of outbound compressed UDP/RTP packets.
C32 cbQosIPHCRtpCmprsOutPktOverflow	1.3.6.1.4.1.9.9.166.1.23.1.1.4	Counter32	read-only	The upper 32 bits count of outbound compressed UDP/RTP packets.
C32 cbQosIPHCRtpSavedByte	1.3.6.1.4.1.9.9.166.1.23.1.1.8	Counter32	read-only	The lower 32 bits count of UDP/RTP bytes that saved due to IPHC.
C64 cbQosIPHCRtpSavedByte64	1.3.6.1.4.1.9.9.166.1.23.1.1.9	Counter64	read-only	The 64 bits count of UDP/RTP bytes that saved due to IPHC.
C32 cbQosIPHCRtpSavedByteOverflow	1.3.6.1.4.1.9.9.166.1.23.1.1.7	Counter32	read-only	The upper 32 bits count of UDP/RTP bytes that saved due to IPHC.
C32 cbQosIPHCRtpSentByte	1.3.6.1.4.1.9.9.166.1.23.1.1.11	Counter32	read-only	The lower 32 bits count of outbound UDP/RTP bytes.
C64 cbQosIPHCRtpSentByte64	1.3.6.1.4.1.9.9.166.1.23.1.1.12	Counter64	read-only	The 64 bits count of outbound UDP/RTP bytes.
C32 cbQosIPHCRtpSentByteOverflow	1.3.6.1.4.1.9.9.166.1.23.1.1.10	Counter32	read-only	The upper 32 bits count of outbound UDP/RTP bytes.
G32 cbQosIPHCRtpSentByteRate	1.3.6.1.4.1.9.9.166.1.23.1.1.13	Gauge32	read-only	The 32 bits count of outbound UDP/RTP byte rate.
C32 cbQosIPHCRtpSentPkt	1.3.6.1.4.1.9.9.166.1.23.1.1.2	Counter32	read-only	The lower 32 bits count of outbound UDP/RTP packets.
C64 cbQosIPHCRtpSentPkt64	1.3.6.1.4.1.9.9.166.1.23.1.1.3	Counter64	read-only	The 64 bits count of outbound UDP/RTP packets.
C32 cbQosIPHCRtpSentPktOverflow	1.3.6.1.4.1.9.9.166.1.23.1.1.1	Counter32	read-only	The upper 32 bits count of outbound UDP/RTP packets.
cbQosIPHCStats	1.3.6.1.4.1.9.9.166.1.23
cbQosIPHCStatsEntry	1.3.6.1.4.1.9.9.166.1.23.1.1		not-accessible	Each entry in this table describes statistical information about IP Header compression. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, namely cbQosPolicyIndex and cbQosObjectsIndex.
cbQosIPHCStatsGroup	1.3.6.1.4.1.9.9.166.2.2.47			Optional objects to provide CB QoS IP header compression statistic information.
cbQosIPHCStatsTable	1.3.6.1.4.1.9.9.166.1.23.1		not-accessible	This table specifies IP Header Compression statistical information.
C32 cbQosIPHCTcpCmprsOutPkt	1.3.6.1.4.1.9.9.166.1.23.1.1.18	Counter32	read-only	The lower 32 bits count of outbound compressed TCP packets.
C64 cbQosIPHCTcpCmprsOutPkt64	1.3.6.1.4.1.9.9.166.1.23.1.1.19	Counter64	read-only	The 64 bits count of outbound compressed TCP packets.
C32 cbQosIPHCTcpCmprsOutPktOverflow	1.3.6.1.4.1.9.9.166.1.23.1.1.17	Counter32	read-only	The upper 32 bits count of outbound compressed TCP packets.
C32 cbQosIPHCTcpSavedByte	1.3.6.1.4.1.9.9.166.1.23.1.1.21	Counter32	read-only	The lower 32 bits count of TCP bytes that saved due to IPHC.
C64 cbQosIPHCTcpSavedByte64	1.3.6.1.4.1.9.9.166.1.23.1.1.22	Counter64	read-only	The 64 bits count of TCP bytes that saved due to IPHC.
C32 cbQosIPHCTcpSavedByteOverflow	1.3.6.1.4.1.9.9.166.1.23.1.1.20	Counter32	read-only	The upper 32 bits count of TCP bytes that saved due to IPHC.
C32 cbQosIPHCTcpSentByte	1.3.6.1.4.1.9.9.166.1.23.1.1.24	Counter32	read-only	The lower 32 bits count of outbound TCP bytes.
C64 cbQosIPHCTcpSentByte64	1.3.6.1.4.1.9.9.166.1.23.1.1.25	Counter64	read-only	The 64 bits count of outbound TCP bytes.
C32 cbQosIPHCTcpSentByteOverflow	1.3.6.1.4.1.9.9.166.1.23.1.1.23	Counter32	read-only	The upper 32 bits count of outbound TCP bytes.
G32 cbQosIPHCTcpSentByteRate	1.3.6.1.4.1.9.9.166.1.23.1.1.26	Gauge32	read-only	The 32 bits count of outbound TCP byte rate.
C32 cbQosIPHCTcpSentPkt	1.3.6.1.4.1.9.9.166.1.23.1.1.15	Counter32	read-only	The lower 32 bits count of outbound TCP packets.
C64 cbQosIPHCTcpSentPkt64	1.3.6.1.4.1.9.9.166.1.23.1.1.16	Counter64	read-only	The 64 bits count of outbound TCP packets.
C32 cbQosIPHCTcpSentPktOverflow	1.3.6.1.4.1.9.9.166.1.23.1.1.14	Counter32	read-only	The upper 32 bits count of outbound TCP packets.
G32 cbQosMatchPrePolicyBitRate	1.3.6.1.4.1.9.9.166.1.16.1.1.7	Gauge32	read-only	The bit rate of the traffic prior to executing any QoS policies.
C32 cbQosMatchPrePolicyByte	1.3.6.1.4.1.9.9.166.1.16.1.1.5	Counter32	read-only	The lower 32 bits count of inbound octets prior to executing any QoS policies.
C64 cbQosMatchPrePolicyByte64	1.3.6.1.4.1.9.9.166.1.16.1.1.6	Counter64	read-only	The 64 bits count of inbound octets prior to executing any QoS policies.
C32 cbQosMatchPrePolicyByteOverflow	1.3.6.1.4.1.9.9.166.1.16.1.1.4	Counter32	read-only	The upper 32 bits count of inbound octets prior to executing any QoS policies.
C32 cbQosMatchPrePolicyPkt	1.3.6.1.4.1.9.9.166.1.16.1.1.2	Counter32	read-only	The lower 32 bits count of inbound packets prior to executing any QoS policies.
C64 cbQosMatchPrePolicyPkt64	1.3.6.1.4.1.9.9.166.1.16.1.1.3	Counter64	read-only	The 64 bits count of inbound packets prior to executing any QoS policies.
C32 cbQosMatchPrePolicyPktOverflow	1.3.6.1.4.1.9.9.166.1.16.1.1.1	Counter32	read-only	The upper 32 bits count of inbound packets prior to executing any QoS policies.
cbQosMatchStmtCfg	1.3.6.1.4.1.9.9.166.1.8
cbQosMatchStmtCfgEntry	1.3.6.1.4.1.9.9.166.1.8.1.1		not-accessible	Each entry in this table describes configuration information about a MatchStatement. The information includes: Name, and whether it is a Match or Match-Not statement. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex of each MatchStatement.
cbQosMatchStmtCfgGroup	1.3.6.1.4.1.9.9.166.2.2.8			Required objects to provide CB QoS objects configuration information.
cbQosMatchStmtCfgTable	1.3.6.1.4.1.9.9.166.1.8.1		not-accessible	This table specifies ClassMap configuration information
QOS cbQosMatchStmtInfo	1.3.6.1.4.1.9.9.166.1.8.1.1.2	QosMatchInfo	read-only	Match vs Match Not in a given class.
STR cbQosMatchStmtName	1.3.6.1.4.1.9.9.166.1.8.1.1.1	DisplayString	read-only	Name of the Match Statement.
cbQosMatchStmtStats	1.3.6.1.4.1.9.9.166.1.16
cbQosMatchStmtStatsEntry	1.3.6.1.4.1.9.9.166.1.16.1.1		not-accessible	Each entry in this table describes the statistical information about Match Statement. Match Statement specific information you can find in this table are : Pre policy pkt/byte counters, and bit rates. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, such as cbQosPolicyIndex and cbQosObjectsIndex.
cbQosMatchStmtStatsGroup	1.3.6.1.4.1.9.9.166.2.2.19			Required objects to provide CB QoS objects configuration information.
cbQosMatchStmtStatsTable	1.3.6.1.4.1.9.9.166.1.16.1		not-accessible	This table specifies Match Statement related statistical information.
cbQosMeasureIPSLACfg	1.3.6.1.4.1.9.9.166.1.31
cbQosMeasureIPSLACfgEntry	1.3.6.1.4.1.9.9.166.1.31.1.1		not-accessible	Each entry describes configuration information about one instance of IPSLAs measure action in the policy map. The table is indexed by the cbQosConfigIndex and cbQosMeasureIPSLACfgGroupIndex.
cbQosMeasureIPSLACfgGroup	1.3.6.1.4.1.9.9.166.2.2.64			Optional objects to configure IPSLA measure action.
U32 cbQosMeasureIPSLACfgGroupIndex	1.3.6.1.4.1.9.9.166.1.31.1.1.1	Unsigned32	read-only	An arbitrary (system-assigned) index for each instance of IPSLAs measure action. The index is unique for each instance for a particular class in particular policy-map. For example consider following configuration: policy-map p1 class c1 measure type ip-sla group g1 measure type ip-sla group g2 class c2 measure type ip-sla group g3 In this case the cbQosMeasureIPSLACfgGroupIndex value for first measure action instance under class c1 will be 1, for second instance it will be 1, and so on. The value for the index will start over again from 1 for class c2.
STR cbQosMeasureIPSLACfgGroupName	1.3.6.1.4.1.9.9.166.1.31.1.1.2	DisplayString	read-only	IPSLAs auto group name. Group is an aggregation of operations sharing the same type, for example udp-jitter type, with common characteristics like frequency, interval etc. Groups are formed by policies dictated either by customer, or by service level or any other requirements.
cbQosMeasureIPSLACfgTable	1.3.6.1.4.1.9.9.166.1.31.1		not-accessible	This table specifies configuration information for measure type IPSLA action. The measure action relates the policy class to a specific IPSLAs auto group. Configuration of measure action of type IPSLA results in automatic generation of IPSLAs synthetic test operations when the policy is attached to interface. The operations are created according to the characteristics specified and to the destinations specified in IPSLA auto group. The IPSLAs sythentic test operations measure network statistics such as latency, packet loss and jitter. This table is to be used only for retrieving the measure action configuration information.
cbQosNewSetCfgGroup	1.3.6.1.4.1.9.9.166.2.2.28			Optional objects to provide CB QoS objects configuration information.
cbQosNoBufferDropGroup	1.3.6.1.4.1.9.9.166.2.2.16			Optional objects to provide CB QoS summary statistics.
cbQosObjects	1.3.6.1.4.1.9.9.166.1.5
cbQosObjectsEntry	1.3.6.1.4.1.9.9.166.1.5.1.1		not-accessible	A QoS object entry. Objects covered in this table are PolicyMap, ClassMap, Match Statements, and Actions. Each entry is indexed by system-generated cbQosPolicyIndex, and cbQosObjectsIndex, which represents a runtime instance of a QoS object. In conjunction with the cbQosParentObjectsIndex, a management station can determine the hierarchical relationship of those QoS objects. Given that classmaps and service policies can be nested entites, each entry in this table represents a unique instance of such object. Each runtime object instance has a corresponding config object, which contains the configuration information of such QoS object. The config object is indexed by cbQosConfigIndex.
cbQosObjectsGroup	1.3.6.1.4.1.9.9.166.2.2.5			Required objects to provide CB QoS objects configuration information.
U32 cbQosObjectsIndex	1.3.6.1.4.1.9.9.166.1.5.1.1.1	Unsigned32	not-accessible	An arbitrary (system-assigned) instance specific index for cbQosObjectsEntry.
cbQosObjectsTable	1.3.6.1.4.1.9.9.166.1.5.1		not-accessible	This table specifies QoS objects (classmap, policymap, match statements, and actions) hierarchy. This table also provide relationship between each PolicyIndex/ObjectsIndex pair and the ConfigIndex. ConfigIndex is essential for querying any configuration tables.
QOS cbQosObjectsType	1.3.6.1.4.1.9.9.166.1.5.1.1.3	QosObjectType	read-only	The type of the QoS object.
U32 cbQosParentObjectsIndex	1.3.6.1.4.1.9.9.166.1.5.1.1.4	Unsigned32	read-only	The parent instance index of a QoS object. For a ClassMap, the parent index would be the index of the attached PolicyMap. For a Match Statement, the parent index would be the index of the ClassMap that uses this Match Statement. For an action, the parent index would be the index of the ClassMap that applies such Action. For a non-hierarchical PolicyMap, the parent would be the logical interface to which the policy is attached, thus the parent index would be 0. For a hierarchical PolicyMap, the parent index would be the index of the ClassMap to which the nested policy is attached.
cbQosPoliceActionCfg	1.3.6.1.4.1.9.9.166.1.21
POL cbQosPoliceActionCfgConform	1.3.6.1.4.1.9.9.166.1.21.1.1.2	PoliceAction	read-only	Action to be taken when the traffic exceeds the conform and exceed token buckets.
U32 cbQosPoliceActionCfgConformSetValue	1.3.6.1.4.1.9.9.166.1.21.1.1.3	Unsigned32	read-only	New packet attribute values for each packet set by police action defined in cbQosPoliceActionCfgConform. This object will be set to zero if the corresponding police action does not require a set value, such as no action, drop action or transmit action.
cbQosPoliceActionCfgEntry	1.3.6.1.4.1.9.9.166.1.21.1.1		not-accessible	Each entry in this table describes configuration information about Actions for one Police. The table holds Police action specific configuration parameters. This table is a sub-table for cbQosPoliceCfgTable. There is a 1-to-1 association between one entry here and one entry in cbQosPoliceCfgTable. This table contains configuration information only, no statistics associated with it. This table has two indices. The first is cbQosConfigIndex which is drived directly from cbQosPoliceCfgTable to keep the 1-to-1 mapping nature between two tables. The second is cbQosPoliceActionCfgIndex used to reference the actual actions configured. The maximum number of actions supported is determined by the system, which is 5 currently.
POL cbQosPoliceActionCfgExceed	1.3.6.1.4.1.9.9.166.1.21.1.1.4	PoliceAction	read-only	Action to be taken when the traffic exceeds the conform and exceed token buckets.
U32 cbQosPoliceActionCfgExceedSetValue	1.3.6.1.4.1.9.9.166.1.21.1.1.5	Unsigned32	read-only	New packet attribute values for each packet set by police action defined in cbQosPoliceActionCfgExceed. This object will be set to zero if the corresponding police action does not require a set value, such as no action, drop action or transmit action.
cbQosPoliceActionCfgGroup	1.3.6.1.4.1.9.9.166.2.2.33			Required objects to provide CB QoS objects configuration information.
U32 cbQosPoliceActionCfgIndex	1.3.6.1.4.1.9.9.166.1.21.1.1.1	Unsigned32	not-accessible	An arbitrary (system-assigned) index for police actions that are defined by a police configuration.
cbQosPoliceActionCfgTable	1.3.6.1.4.1.9.9.166.1.21.1		not-accessible	This table specifies Police Action configuration information.
POL cbQosPoliceActionCfgViolate	1.3.6.1.4.1.9.9.166.1.21.1.1.6	PoliceAction	read-only	Action to be taken when the traffic exceeds the conform and exceed token buckets.
U32 cbQosPoliceActionCfgViolateSetValue	1.3.6.1.4.1.9.9.166.1.21.1.1.7	Unsigned32	read-only	New packet attribute values for each packet set by police action defined in cbQosPoliceActionCfgViolate. This object will be set to zero if the corresponding police action does not require a set value, such as no action, drop action or transmit action.
cbQosPoliceCfg	1.3.6.1.4.1.9.9.166.1.12
U32 cbQosPoliceCfgBurstCell	1.3.6.1.4.1.9.9.166.1.12.1.1.17	Unsigned32	read-only	The amount of traffic, in cells, in excess of the committed policing rate that will be permitted by the policing feature.
U32 cbQosPoliceCfgBurstSize	1.3.6.1.4.1.9.9.166.1.12.1.1.2	Unsigned32	read-only	The amount of traffic, in bytes, in excess of the committed policing rate that will be permitted by the policing feature.
U32 cbQosPoliceCfgBurstTime	1.3.6.1.4.1.9.9.166.1.12.1.1.19	Unsigned32	read-only	The amount of traffic time, in ms, in excess of the committed policing rate that will be permitted by the policing feature. The milli-second value is internally converted to bytes by using the bandwidth that is available for the class.
U32 cbQosPoliceCfgCdvt	1.3.6.1.4.1.9.9.166.1.12.1.1.21	Unsigned32	read-only	The ATM Cell Delay Variation Tolerance value.
cbQosPoliceCfgCdvtGroup	1.3.6.1.4.1.9.9.166.2.2.53			Optional objects to provide CB QoS policing ATM CDVT configuration information.
cbQosPoliceCfgCellGroup	1.3.6.1.4.1.9.9.166.2.2.51			Optional objects to provide CB QoS policing cell based rate configuration information.
U32 cbQosPoliceCfgCellPir	1.3.6.1.4.1.9.9.166.1.12.1.1.16	Unsigned32	read-only	The peak policing rate in cells/second. Its value is valid only when cbQosPoliceCfgRateType equals to 3.
U32 cbQosPoliceCfgCellRate	1.3.6.1.4.1.9.9.166.1.12.1.1.15	Unsigned32	read-only	The committed policing rate in cells/second. Its value is valid only when cbQosPoliceCfgRateType equals to 3.
cbQosPoliceCfgColorGroup	1.3.6.1.4.1.9.9.166.2.2.54			Optional objects to provide CB QoS policing color aware configuration information.
T/F cbQosPoliceCfgConditional	1.3.6.1.4.1.9.9.166.1.12.1.1.24	TruthValue	read-only	This object is use to depict weather police is configured as a conditioniler policer or not
POL cbQosPoliceCfgConformAction	1.3.6.1.4.1.9.9.166.1.12.1.1.4	PoliceAction	read-only	Action to be taken when the traffic is within the configured rate, that is, the traffic rate is conforming. This object is deprecated and defined in cbQosPoliceActionCfgTable.
STR cbQosPoliceCfgConformColor	1.3.6.1.4.1.9.9.166.1.12.1.1.22	DisplayString	read-only	The Classmap name used in AF color-aware mode to specify the conform-color for the incoming packets which was marked by the previous node. At least conform-color must be specified. If only conform-color is specified, all other packets are assumed to be marked exceed. See RFC 2697, A Single Rate Three Color Marker. See RFC 2698, A Two Rate Three Color Marker.
U32 cbQosPoliceCfgConformSetValue	1.3.6.1.4.1.9.9.166.1.12.1.1.5	Unsigned32	read-only	New packet attribute values for each packets that conforms to the configured Police rate. This object is deprecated and defined in cbQosPoliceActionCfgTable.
cbQosPoliceCfgEntry	1.3.6.1.4.1.9.9.166.1.12.1.1		not-accessible	Each entry in this table describes configuration information about a Police Action. The table holds Policy configuration parameters, such as rate, burst size, and actions based on traffic rates. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex.
POL cbQosPoliceCfgExceedAction	1.3.6.1.4.1.9.9.166.1.12.1.1.6	PoliceAction	read-only	Action to be taken when the traffic exceeds the configured rate, that is, the traffic is non-conforming. This object is deprecated and defined in cbQosPoliceActionCfgTable.
STR cbQosPoliceCfgExceedColor	1.3.6.1.4.1.9.9.166.1.12.1.1.23	DisplayString	read-only	The Classmap name used in AF color-aware mode to specify the exceed-color for the incoming packets which was marked by the previous node. If both conform-color and exceed-color are specified, all other packets are assumed to be marked violate. Violate-color configuration is not needed.
U32 cbQosPoliceCfgExceedSetValue	1.3.6.1.4.1.9.9.166.1.12.1.1.7	Unsigned32	read-only	New packet attribute values for each packets that conforms to the configured Police rate. This object is deprecated and defined in cbQosPoliceActionCfgTable.
U32 cbQosPoliceCfgExtBurstCell	1.3.6.1.4.1.9.9.166.1.12.1.1.18	Unsigned32	read-only	The amount of traffic, in cells, in excess of the burst limit, which may be conditionally permitted by the policing feature. The probability that the traffic is not permitted increases as the received burst size increases.
U32 cbQosPoliceCfgExtBurstSize	1.3.6.1.4.1.9.9.166.1.12.1.1.3	Unsigned32	read-only	The amount of traffic, in bytes, in excess of the burst limit, which may be conditionally permitted by the policing feature. The probability that the traffic is not permitted increases as the received burst size increases.
U32 cbQosPoliceCfgExtBurstTime	1.3.6.1.4.1.9.9.166.1.12.1.1.20	Unsigned32	read-only	The amount of traffic time, in ms, in excess of the burst limit, which may be conditionally permitted by the policing feature. The probability that the traffic is not permitted increases as the received burst size increases. The milli-second value is internally converted to bytes by using the bandwidth that is available for the class.
cbQosPoliceCfgExtGroup	1.3.6.1.4.1.9.9.166.2.2.37			Optional objects to provide the information of the committed policing rate that is greater than the maximum value reportable by cbQosPoliceCfgRate.
cbQosPoliceCfgGroup	1.3.6.1.4.1.9.9.166.2.2.12			Required objects to provide CB QoS objects configuration information.
cbQosPoliceCfgGroupRev1	1.3.6.1.4.1.9.9.166.2.2.32			Required objects to provide CB QoS objects configuration information.
cbQosPoliceCfgGroupRev2	1.3.6.1.4.1.9.9.166.2.2.42			Required objects to provide CB QoS objects configuration information for POLICE feature.
cbQosPoliceCfgGroupRev3	1.3.6.1.4.1.9.9.166.2.2.70			Required objects to provide CB QoS objects configuration information for POLICE feature
cbQosPoliceCfgPercentGroup	1.3.6.1.4.1.9.9.166.2.2.44			Optional objects to provide CB QoS policing CIR and PIR rates in percentage.
U32 cbQosPoliceCfgPercentPirValue	1.3.6.1.4.1.9.9.166.1.12.1.1.14	Unsigned32	read-only	The peak policing rate in percentage. Its value is valid only when cbQosPoliceCfgRateType equals to 2.
U32 cbQosPoliceCfgPercentRateValue	1.3.6.1.4.1.9.9.166.1.12.1.1.13	Unsigned32	read-only	The committed policing rate in percentage. Its value is valid only when cbQosPoliceCfgRateType equals to 2.
U32 cbQosPoliceCfgPir	1.3.6.1.4.1.9.9.166.1.12.1.1.10	Unsigned32	read-only	The committed policing rate. This is the peak rate permitted by two rate policing.
cbQosPoliceCfgPirGroup	1.3.6.1.4.1.9.9.166.2.2.43			Optional objects to provide CB QoS policing PIR rate.
U32 cbQosPoliceCfgRate	1.3.6.1.4.1.9.9.166.1.12.1.1.1	Unsigned32	read-only	The committed policing rate. This is the sustained rate permitted by policing. If a committed policing rate greater than 2000000000 is configurable on the system, then the configured rate is available in cbQosPoliceCfgRate64.
UNS cbQosPoliceCfgRate64	1.3.6.1.4.1.9.9.166.1.12.1.1.11	Unsigned64	read-only	The committed policing rate. This is the sustained rate permitted by policing.
CBQ cbQosPoliceCfgRateType	1.3.6.1.4.1.9.9.166.1.12.1.1.12	CbQosRateType	read-only	The rate type that configured for CIR & PIR. 1 means rates are configured in bps. 2 means rates are configured in percentage. 3 means rates are configured in cps.
cbQosPoliceCfgTable	1.3.6.1.4.1.9.9.166.1.12.1		not-accessible	This table specifies Police Action configuration information.
cbQosPoliceCfgTimeGroup	1.3.6.1.4.1.9.9.166.2.2.52			Optional objects to provide CB QoS policing time based burst size configuration information.
POL cbQosPoliceCfgViolateAction	1.3.6.1.4.1.9.9.166.1.12.1.1.8	PoliceAction	read-only	Action to be taken when the traffic exceeds the conform and exceed token buckets. This object is deprecated and defined in cbQosPoliceActionCfgTable.
U32 cbQosPoliceCfgViolateSetValue	1.3.6.1.4.1.9.9.166.1.12.1.1.9	Unsigned32	read-only	New packet attribute values for each packets that conforms to the Police violate action. The packet attibute values depend on the action that is taken for the particular packet. For example, if the action was to set the dscp value, this entry describes the value it is set to. This object is deprecated and defined in cbQosPoliceActionCfgTable.
C64 cbQosPoliceCfmColorCfmByte64	1.3.6.1.4.1.9.9.166.1.25.1.1.2	Counter64	read-only	The 64 bits count of bytes which are marked as Conform-Color by previous node and treated as conforming by the policing feature on this node.
C64 cbQosPoliceCfmColorCfmPkt64	1.3.6.1.4.1.9.9.166.1.25.1.1.1	Counter64	read-only	The 64 bits count of packets which are marked as Conform-Color by previous node and treated as conforming by the policing feature on this node.
C64 cbQosPoliceCfmColorExdByte64	1.3.6.1.4.1.9.9.166.1.25.1.1.4	Counter64	read-only	The 64 bits count of bytes which are marked as Conform-Color by previous node and treated as exceeding by the policing feature on this node.
C64 cbQosPoliceCfmColorExdPkt64	1.3.6.1.4.1.9.9.166.1.25.1.1.3	Counter64	read-only	The 64 bits count of packets which are marked as Conform-Color by previous node and treated as exceeding by the policing feature on this node.
C64 cbQosPoliceCfmColorVltByte64	1.3.6.1.4.1.9.9.166.1.25.1.1.6	Counter64	read-only	The 64 bits count of bytes which are marked as Conform-Color by previous node and treated as violating by the policing feature on this node.
C64 cbQosPoliceCfmColorVltPkt64	1.3.6.1.4.1.9.9.166.1.25.1.1.5	Counter64	read-only	The 64 bits count of packets which are marked as Conform-Color by previous node and treated as violating by the policing feature on this node.
cbQosPoliceColorStats	1.3.6.1.4.1.9.9.166.1.25
cbQosPoliceColorStatsEntry	1.3.6.1.4.1.9.9.166.1.25.1.1		not-accessible	Each entry in this table describes the statistical information about Police Action for Two Rate Color Aware Marker. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, such as cbQosPolicyIndex and cbQosObjectsIndex.
cbQosPoliceColorStatsGroup	1.3.6.1.4.1.9.9.166.2.2.59			Optional objects to provide CB QoS Assured Forwarding Policing Color Aware statistical information.
cbQosPoliceColorStatsTable	1.3.6.1.4.1.9.9.166.1.25.1		not-accessible	This table specifies Police Action related Statistical information for two rate color aware marker.
G32 cbQosPoliceConformedBitRate	1.3.6.1.4.1.9.9.166.1.17.1.1.7	Gauge32	read-only	The bit rate of conforming traffic.
C32 cbQosPoliceConformedByte	1.3.6.1.4.1.9.9.166.1.17.1.1.5	Counter32	read-only	The lower 32 bits count of octets treated as conforming by the policing feature.
C64 cbQosPoliceConformedByte64	1.3.6.1.4.1.9.9.166.1.17.1.1.6	Counter64	read-only	The 64 bits count of octets treated as conforming by the policing feature.
C32 cbQosPoliceConformedByteOverflow	1.3.6.1.4.1.9.9.166.1.17.1.1.4	Counter32	read-only	The upper 32 bits count of octets treated as conforming by the policing feature.
C32 cbQosPoliceConformedPkt	1.3.6.1.4.1.9.9.166.1.17.1.1.2	Counter32	read-only	The lower 32 bits count of packets treated as conforming by the policing feature.
C64 cbQosPoliceConformedPkt64	1.3.6.1.4.1.9.9.166.1.17.1.1.3	Counter64	read-only	The 64 bits count of packets treated as conforming by the policing feature.
C32 cbQosPoliceConformedPktOverflow	1.3.6.1.4.1.9.9.166.1.17.1.1.1	Counter32	read-only	The upper 32 bits count of packets treated as conforming by the policing feature.
G32 cbQosPoliceExceededBitRate	1.3.6.1.4.1.9.9.166.1.17.1.1.14	Gauge32	read-only	The bit rate of the non-conforming traffic.
C32 cbQosPoliceExceededByte	1.3.6.1.4.1.9.9.166.1.17.1.1.12	Counter32	read-only	The lower 32 bits count of octets treated as non-conforming by the policing feature.
C64 cbQosPoliceExceededByte64	1.3.6.1.4.1.9.9.166.1.17.1.1.13	Counter64	read-only	The 64 bits count of octets treated as non-conforming by the policing feature.
C32 cbQosPoliceExceededByteOverflow	1.3.6.1.4.1.9.9.166.1.17.1.1.11	Counter32	read-only	The upper 32 bits count of octets treated as non-conforming by the policing feature.
C32 cbQosPoliceExceededPkt	1.3.6.1.4.1.9.9.166.1.17.1.1.9	Counter32	read-only	The 32 bits count of packets treated as non-conforming by the policing feature.
C64 cbQosPoliceExceededPkt64	1.3.6.1.4.1.9.9.166.1.17.1.1.10	Counter64	read-only	The 64 bits count of packets treated as non-conforming by the policing feature.
C32 cbQosPoliceExceededPktOverflow	1.3.6.1.4.1.9.9.166.1.17.1.1.8	Counter32	read-only	The upper 32 bits count of packets treated as non-conforming by the policing feature.
C64 cbQosPoliceExdColorExdByte64	1.3.6.1.4.1.9.9.166.1.25.1.1.8	Counter64	read-only	The 64 bits count of bytes which are marked as Exceed-Color by previous node and treated as exceeding by the policing feature on this node.
C64 cbQosPoliceExdColorExdPkt64	1.3.6.1.4.1.9.9.166.1.25.1.1.7	Counter64	read-only	The 64 bits count of packets which are marked as Exceed-Color by previous node and treated as exceeding by the policing feature on this node.
C64 cbQosPoliceExdColorVltByte64	1.3.6.1.4.1.9.9.166.1.25.1.1.10	Counter64	read-only	The 64 bits count of bytes which are marked as Exceed-Color by previous node and treated as violating by the policing feature on this node.
C64 cbQosPoliceExdColorVltPkt64	1.3.6.1.4.1.9.9.166.1.25.1.1.9	Counter64	read-only	The 64 bits count of packets which are marked as Exceed-Color by previous node and treated as violating by the policing feature on this node.
cbQosPoliceStats	1.3.6.1.4.1.9.9.166.1.17
cbQosPoliceStatsEntry	1.3.6.1.4.1.9.9.166.1.17.1.1		not-accessible	Each entry in this table describes the statistical information about Police Action. Police Action specific information you can find in this table are : Conformed/Exceeded pkt/byte counters, bit rates. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, such as cbQosPolicyIndex and cbQosObjectsIndex.
cbQosPoliceStatsGroup	1.3.6.1.4.1.9.9.166.2.2.20			Required objects to provide CB QoS objects configuration information.
cbQosPoliceStatsTable	1.3.6.1.4.1.9.9.166.1.17.1		not-accessible	This table specifies Police Action related Statistical information.
G32 cbQosPoliceViolatedBitRate	1.3.6.1.4.1.9.9.166.1.17.1.1.21	Gauge32	read-only	The bit rate of the violating traffic.
C32 cbQosPoliceViolatedByte	1.3.6.1.4.1.9.9.166.1.17.1.1.19	Counter32	read-only	The lower 32 bits count of octets treated as violated by the policing feature.
C64 cbQosPoliceViolatedByte64	1.3.6.1.4.1.9.9.166.1.17.1.1.20	Counter64	read-only	The 64 bits count of octets treated as violated by the policing feature.
C32 cbQosPoliceViolatedByteOverflow	1.3.6.1.4.1.9.9.166.1.17.1.1.18	Counter32	read-only	The upper 32 bits count of octets treated as violated by the policing feature.
C32 cbQosPoliceViolatedPkt	1.3.6.1.4.1.9.9.166.1.17.1.1.16	Counter32	read-only	The 32 bits count of packets treated as violated by the policing feature.
C64 cbQosPoliceViolatedPkt64	1.3.6.1.4.1.9.9.166.1.17.1.1.17	Counter64	read-only	The 64 bits count of packets treated as violated by the policing feature.
C32 cbQosPoliceViolatedPktOverflow	1.3.6.1.4.1.9.9.166.1.17.1.1.15	Counter32	read-only	The upper 32 bits count of packets treated as violated by the policing feature.
C64 cbQosPoliceVltColorVltByte64	1.3.6.1.4.1.9.9.166.1.25.1.1.12	Counter64	read-only	The 64 bits count of bytes which are marked as Violate-Color by previous node and treated as violating by the policing feature on this node.
C64 cbQosPoliceVltColorVltPkt64	1.3.6.1.4.1.9.9.166.1.25.1.1.11	Counter64	read-only	The 64 bits count of packets which are marked as Violate-Color by previous node and treated as violating by the policing feature on this node.
TRA cbQosPolicyDirection	1.3.6.1.4.1.9.9.166.1.1.1.1.3	TrafficDirection	read-only	This indicates the direction of traffic for which this service policy is applied.
U32 cbQosPolicyIndex	1.3.6.1.4.1.9.9.166.1.1.1.1.1	Unsigned32	not-accessible	An arbitrary (system-assigned) index for all service policies (PolicyMap that has been attached to a given logical interface).
cbQosPolicyMapCfg	1.3.6.1.4.1.9.9.166.1.6
cbQosPolicyMapCfgEntry	1.3.6.1.4.1.9.9.166.1.6.1.1		not-accessible	Each entry in this table describes configuration information about a policymap. The information includes: Name, and it's description. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex of each PolicyMap.
cbQosPolicyMapCfgGroup	1.3.6.1.4.1.9.9.166.2.2.6			Required objects to provide CB QoS objects configuration information.
cbQosPolicyMapCfgTable	1.3.6.1.4.1.9.9.166.1.6.1		not-accessible	This table specifies Policymap configuration information
STR cbQosPolicyMapDesc	1.3.6.1.4.1.9.9.166.1.6.1.1.2	DisplayString	read-only	Description of the PolicyMap.
STR cbQosPolicyMapName	1.3.6.1.4.1.9.9.166.1.6.1.1.1	DisplayString	read-only	Name of the Policymap.
I32 cbQosQlimitWeightValue	1.3.6.1.4.1.9.9.166.1.32.1.1.2	Integer32	not-accessible	This object depict the weight value configured for weighted Queue-limit. The Weight value is IP precedence or IP DSCP of this entry.
cbQosQueueingCfg	1.3.6.1.4.1.9.9.166.1.9
CBQ cbQosQueueingCfgAggregateQLimit	1.3.6.1.4.1.9.9.166.1.9.1.1.10	CbQosQueueDepth	read-only	Maximum allowed queue size for all the individual queues associated with this class. When the queue size exceed this value, the packets will be dropped.
I32 cbQosQueueingCfgAggregateQSize	1.3.6.1.4.1.9.9.166.1.9.1.1.5	Integer32	read-only	Maximum number of packets that can be held in all the individual queues associated with this class before packets are dropped. This object is deprecated by cbQosQueueingCfgAggregateQLimit.
U32 cbQosQueueingCfgAggrQLimitTime	1.3.6.1.4.1.9.9.166.1.9.1.1.11	Unsigned32	read-only	Maximum allowed queue size in milli-seconds for all individual queues associated with this class. It is internally converted to bytes by using the bandwidth that is available for the class.
I32 cbQosQueueingCfgBandwidth	1.3.6.1.4.1.9.9.166.1.9.1.1.1	Integer32	read-only	The type of bandwidth configuration value represented by this object is indicated by the value of cbQosQueueingCfgBandwidthUnits for this entry. If the cbQosQueueingCfgBandwidthUnits value is 'kbps(1)' or 'percentage(2)', this object represents the configured bandwidth allocated to this traffic class.In the case of a bandwidth policy, this value represents a minimum bandwidth guarantee for the traffic class. In the case of a priority policy, this value represents the maximum rate at which priority service is guaranteed. If the cbQosQueueingCfgBandwidthUnits value is 'percentageRemaining(3)', this object represents the the percentage of the unallocated bandwidth to allocate to this class. If the cbQosQueueingCfgBandwidthUnits value is 'ratioRemaining(4)', this object represents the ratio value, relative to other class' configured ratio values, used to determine the portion of the unallocated bandwidth to apply to this class.
QUE cbQosQueueingCfgBandwidthUnits	1.3.6.1.4.1.9.9.166.1.9.1.1.2	QueueingBandwidthUnits	read-only	Units of the accompanying cbQosQueueingCfgbandwidth parameter
I32 cbQosQueueingCfgDynamicQNumber	1.3.6.1.4.1.9.9.166.1.9.1.1.7	Integer32	read-only	Number of dynamic queues supported when flow-based fair-queue is in use.
cbQosQueueingCfgEntry	1.3.6.1.4.1.9.9.166.1.9.1.1		not-accessible	Each entry in this table describes configuration information about a queueing action. The information includes: Bandwidth, Units, Flow Enabled, Priority Enabled, and Q size. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex of each Queueing Action.
T/F cbQosQueueingCfgFlowEnabled	1.3.6.1.4.1.9.9.166.1.9.1.1.3	TruthValue	read-only	Boolean to indicate if flow-based fair-queue is enabled for this class.
cbQosQueueingCfgGroup	1.3.6.1.4.1.9.9.166.2.2.9			Required objects to provide CB QoS objects configuration information.
cbQosQueueingCfgGroupRev1	1.3.6.1.4.1.9.9.166.2.2.29			Required objects to provide CB QoS objects configuration information.
cbQosQueueingCfgGroupRev2	1.3.6.1.4.1.9.9.166.2.2.66			Required objects to provide CB QoS objects configuration information
I32 cbQosQueueingCfgIndividualQSize	1.3.6.1.4.1.9.9.166.1.9.1.1.6	Integer32	read-only	Maximum number of packets that can be held in an individual Flow-based fair-queue associated with this class before it drops packets (once the AggregateQSize has been reached). This field only makes sense in the context of Flow-based fair-queueing.
U32 cbQosQueueingCfgPrioBurstSize	1.3.6.1.4.1.9.9.166.1.9.1.1.8	Unsigned32	read-only	In the priority queue, this is the number of bytes allowed in a single burst. This parameter only makes sense if Priority is enabled
T/F cbQosQueueingCfgPriorityEnabled	1.3.6.1.4.1.9.9.166.1.9.1.1.4	TruthValue	read-only	Boolean to indicate if low latency queueing (priority) is enabled for this class.
U32 cbQosQueueingCfgPriorityLevel	1.3.6.1.4.1.9.9.166.1.9.1.1.12	Unsigned32	read-only	The priority level of the queue into which packets matching this class are queued into. A larger priority level indicates higher priority.
cbQosQueueingCfgQLimitTimeGroup	1.3.6.1.4.1.9.9.166.2.2.49			Optional object to provide Aggregate Queue time based Limit configuration information.
CBQ cbQosQueueingCfgQLimitUnits	1.3.6.1.4.1.9.9.166.1.9.1.1.9	CbQosQueueUnitType	read-only	Represents the unit type of cbQosQueueingCfgAggregateQLimit object.
cbQosQueueingCfgTable	1.3.6.1.4.1.9.9.166.1.9.1		not-accessible	This table specifies Queueing Action configuration information
cbQosQueueingClassCfg	1.3.6.1.4.1.9.9.166.1.32
cbQosQueueingClassCfgEntry	1.3.6.1.4.1.9.9.166.1.32.1.1		not-accessible	Each entry in this table describes configuration information about a weighted queueing action. The information includes: Threshold value, Units and wieght Type (ip,dscp,mplsExp) This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex(which refers to cbQosConfigIndex of cbQosQueueingCfgEntry) and cbQosQueueingClassConfigIndex cbQosQlimitWeightValue i.e(prec,dscp,discard-class,qos-group,atm-clp, mplsExp) of each Weighted Queueing Action.
cbQosQueueingClassCfgGroup	1.3.6.1.4.1.9.9.166.2.2.69			Required objects to provide CB QoS objects configuration information
QUE cbQosQueueingClassCfgQLimitWeight	1.3.6.1.4.1.9.9.166.1.32.1.1.5	QueueMechanism	read-only	This objects depict the weight value for Weighted Queue limit configured i.e(precedence,dscp,qos-group,atm-clp,discard-class,mplsExp) .
cbQosQueueingClassCfgTable	1.3.6.1.4.1.9.9.166.1.32.1		not-accessible	This table specifies the configuration information for weighted queue limit action per IP precedence basis.
CBQ cbQosQueueingClassCfgThreshold	1.3.6.1.4.1.9.9.166.1.32.1.1.3	CbQosQueueDepth	read-only	This object is used to depict the Threshold value for the Weighted Queue Limit.
CBQ cbQosQueueingClassCfgThresholdUnit	1.3.6.1.4.1.9.9.166.1.32.1.1.4	CbQosQueueUnitType	read-only	This object is used to depict the Threshold Unit for the Weighted Queue Limit
I32 cbQosQueueingClassConfigIndex	1.3.6.1.4.1.9.9.166.1.32.1.1.1	Integer32	not-accessible	This objects depict the config index for Weighted Queue limit configured.
G32 cbQosQueueingCurrentQDepth	1.3.6.1.4.1.9.9.166.1.18.1.1.1	Gauge32	read-only	The current depth of the queue.
C32 cbQosQueueingDiscardByte	1.3.6.1.4.1.9.9.166.1.18.1.1.4	Counter32	read-only	The lower 32 bits count of octets, associated with this class, that were dropped by queueing.
C64 cbQosQueueingDiscardByte64	1.3.6.1.4.1.9.9.166.1.18.1.1.5	Counter64	read-only	The count of octets, associated with this class, that were dropped by queueing.
C32 cbQosQueueingDiscardByteOverflow	1.3.6.1.4.1.9.9.166.1.18.1.1.3	Counter32	read-only	The upper 32 bit count of octets, associated with this class, that were dropped by queueing.
C32 cbQosQueueingDiscardPkt	1.3.6.1.4.1.9.9.166.1.18.1.1.7	Counter32	read-only	The number of packets, associated with this class, that were dropped by queueing.
C64 cbQosQueueingDiscardPkt64	1.3.6.1.4.1.9.9.166.1.18.1.1.8	Counter64	read-only	The number of packets, associated with this class, that were dropped by queueing.
C32 cbQosQueueingDiscardPktOverflow	1.3.6.1.4.1.9.9.166.1.18.1.1.6	Counter32	read-only	The upper 32 bits count of packets, associated with this class, that were dropped by queueing.
cbQosQueueingDynamicQNumberGroup	1.3.6.1.4.1.9.9.166.2.2.17			Optional objects to provide CB QoS Queueing information.
G32 cbQosQueueingMaxQDepth	1.3.6.1.4.1.9.9.166.1.18.1.1.2	Gauge32	read-only	The maximum depth of the queue.
cbQosQueueingStats	1.3.6.1.4.1.9.9.166.1.18
cbQosQueueingStatsEntry	1.3.6.1.4.1.9.9.166.1.18.1.1		not-accessible	Each entry in this table describes the statistical information about queueing action. Queueing action specific information you can find in this table are : various Q depth, and discard pkt/byte counters. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, such as cbQosPolicyIndex and cbQosObjectsIndex.
cbQosQueueingStatsGroup	1.3.6.1.4.1.9.9.166.2.2.21			Required objects to provide CB QoS objects configuration information.
cbQosQueueingStatsTable	1.3.6.1.4.1.9.9.166.1.18.1		not-accessible	This table specifies Queueing Action related Statistical information.
cbQosREDCfg	1.3.6.1.4.1.9.9.166.1.10
RED cbQosREDCfgDscpPrec	1.3.6.1.4.1.9.9.166.1.10.1.1.3	REDMechanism	read-only	The Classification mechanism used by RED
T/F cbQosREDCfgECNEnabled	1.3.6.1.4.1.9.9.166.1.10.1.1.4	TruthValue	read-only	Boolean to indicate if explicit congestion notification enabled for this class.
cbQosREDCfgEntry	1.3.6.1.4.1.9.9.166.1.10.1.1		not-accessible	Each entry in this table describes configuration information about a WRED Action. The table holds global (per traffic class) configuration like: Expon Weight and Mean Q size. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex of each WRED Action.
I32 cbQosREDCfgExponWeight	1.3.6.1.4.1.9.9.166.1.10.1.1.1	Integer32	read-only	The decay factor for the queue average calculation. The decay factor is equal to raising 2 to the power of N, where N could be up to 16. The smaller the number, the faster it decays.
cbQosREDCfgGroup	1.3.6.1.4.1.9.9.166.2.2.10			Required objects to provide CB QoS objects configuration information.
cbQosREDCfgGroupRev1	1.3.6.1.4.1.9.9.166.2.2.30			Required objects to provide CB QoS objects configuration information.
I32 cbQosREDCfgMaxThreshold	1.3.6.1.4.1.9.9.166.1.11.1.1.3	Integer32	read-only	Maximum threshold in number of packets. When the average queue length exceeds this number, WRED drops all packets with the specified IP precedence. This is deprecated by cbQosREDClassCfgMaxThreshold.
I32 cbQosREDCfgMeanQsize	1.3.6.1.4.1.9.9.166.1.10.1.1.2	Integer32	read-only	The average queue size, computed and used by the WRED algorithm. This is deprecated by cbQosREDMeanQsize.
I32 cbQosREDCfgMinThreshold	1.3.6.1.4.1.9.9.166.1.11.1.1.2	Integer32	read-only	Minimum threshold in number of packets. When the average queue length reaches this number, WRED begins to drop packets with the specified IP precedence. This is deprecated by cbQosREDClassCfgMinThreshold.
I32 cbQosREDCfgPktDropProb	1.3.6.1.4.1.9.9.166.1.11.1.1.4	Integer32	read-only	Denominator for the fraction of packets dropped when the average queue depth is MaxDepthThreshold. For example, if the denominator is 10, one out of every 10 packets is dropped when the average queue is at the MaxDepthThreshold.
cbQosREDCfgTable	1.3.6.1.4.1.9.9.166.1.10.1		not-accessible	This table specifies WRED Action configuration information
cbQosREDCfgThresholdTimeGroup	1.3.6.1.4.1.9.9.166.2.2.50			Optional objects to provide WRED time based threshold Limit configuration information.
cbQosREDClassCfg	1.3.6.1.4.1.9.9.166.1.11
cbQosREDClassCfgEntry	1.3.6.1.4.1.9.9.166.1.11.1.1		not-accessible	Each entry in this table describes configuration information about a WRED Action. The table holds the per IP precedence based WRED configuration parameters. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex and cbQosREDValue of each WRED Action.
cbQosREDClassCfgGroup	1.3.6.1.4.1.9.9.166.2.2.11			Required objects to provide CB QoS objects configuration information.
cbQosREDClassCfgGroupRev1	1.3.6.1.4.1.9.9.166.2.2.31			Required objects to provide CB QoS objects configuration information.
cbQosREDClassCfgGroupRev2	1.3.6.1.4.1.9.9.166.2.2.68			Required objects to provide CB QoS objects configuration information.
CBQ cbQosREDClassCfgMaxThreshold	1.3.6.1.4.1.9.9.166.1.11.1.1.7	CbQosQueueDepth	read-only	The maximum WRED threshold value. When the average queue length exceeds this number, WRED drops all packets according to REDMechanism specificed in cbQosREDCfgDscpPrec.
U32 cbQosREDClassCfgMaxThresholdTime	1.3.6.1.4.1.9.9.166.1.11.1.1.9	Unsigned32	read-only	The maximum WRED threshold value specified in milli-seconds. The milli-second value is internally converted to bytes by using the bandwidth that is available for the class.
CBQ cbQosREDClassCfgMaxThresholdUnit	1.3.6.1.4.1.9.9.166.1.11.1.1.10	CbQosQueueUnitType	read-only	Represents the unit type to measure the RED Maximum thresholds. The objects covered is cbQosREDClassCfgMaxThreshold
CBQ cbQosREDClassCfgMinThreshold	1.3.6.1.4.1.9.9.166.1.11.1.1.6	CbQosQueueDepth	read-only	The minimum WRED threshold value. When the average queue length reaches this number, WRED begins to drop packets according to REDMechanism specificed in cbQosREDCfgDscpPrec.
U32 cbQosREDClassCfgMinThresholdTime	1.3.6.1.4.1.9.9.166.1.11.1.1.8	Unsigned32	read-only	The minimum WRED threshold value specified in milli-seconds. The milli-second value is internally converted to bytes by using the bandwidth that is available for the class.
CBQ cbQosREDClassCfgMinThresholdUnit	1.3.6.1.4.1.9.9.166.1.11.1.1.11	CbQosQueueUnitType	read-only	Represents the unit type to measure the RED Minimum thresholds. The objects covered is cbQosREDClassCfgMinThreshold
cbQosREDClassCfgTable	1.3.6.1.4.1.9.9.166.1.11.1		not-accessible	This table specifies WRED Action configuration information on a per IP precedence basis.
CBQ cbQosREDClassCfgThresholdUnit	1.3.6.1.4.1.9.9.166.1.11.1.1.5	CbQosQueueUnitType	read-only	Represents the unit type to measure the RED thresholds. The objects covered are cbQosREDClassCfgMinThreshold and cbQosREDClassCfgMaxThreshold
cbQosREDClassECNMarkCountersGroup	1.3.6.1.4.1.9.9.166.2.2.36			Optional objects to provide CB QoS objects configuration information.
cbQosREDClassStats	1.3.6.1.4.1.9.9.166.1.20
cbQosREDClassStatsEntry	1.3.6.1.4.1.9.9.166.1.20.1.1		not-accessible	Each entry in this table describes the statistical information about per Precedence WRED Action. per Precedence WRED Action specific information you can find in this table are : Random pkt/byte counters, and Tail drop pkt/byte counters. This table contains per Precedence/dscp based statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, and a per Precedence identifier: cbQosPolicyIndex, cbQosObjectsIndex and cbQosREDValue.
cbQosREDClassStatsGroup	1.3.6.1.4.1.9.9.166.2.2.23			Required objects to provide CB QoS objects configuration information.
cbQosREDClassStatsTable	1.3.6.1.4.1.9.9.166.1.20.1		not-accessible	This table specifies per Precedence WRED Action related Statistical information.
cbQosREDClassXmitCountersGroup	1.3.6.1.4.1.9.9.166.2.2.24			Optional objects to provide CB QoS objects configuration information.
cbQosREDDscpCfgGroup	1.3.6.1.4.1.9.9.166.2.2.27			Required objects to provide CB QoS objects configuration information.
cbQosREDECNCfgGroup	1.3.6.1.4.1.9.9.166.2.2.35			Optional objects to provide CB QoS objects configuration information.
C32 cbQosREDECNMarkByte	1.3.6.1.4.1.9.9.166.1.20.1.1.23	Counter32	read-only	The lower 32 bits count of bytes ecn marked when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C64 cbQosREDECNMarkByte64	1.3.6.1.4.1.9.9.166.1.20.1.1.24	Counter64	read-only	The 64 bits count of bytes ecn marked when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosREDECNMarkByteOverflow	1.3.6.1.4.1.9.9.166.1.20.1.1.22	Counter32	read-only	The upper 32 bits count of bytes ecn marked when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosREDECNMarkPkt	1.3.6.1.4.1.9.9.166.1.20.1.1.20	Counter32	read-only	The lower 32 bits count of packets ecn marked when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C64 cbQosREDECNMarkPkt64	1.3.6.1.4.1.9.9.166.1.20.1.1.21	Counter64	read-only	The 64 bits count of packets ecn marked when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosREDECNMarkPktOverflow	1.3.6.1.4.1.9.9.166.1.20.1.1.19	Counter32	read-only	The upper 32 bits count of packets ecn marked when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
CBQ cbQosREDMeanQSize	1.3.6.1.4.1.9.9.166.1.20.1.1.26	CbQosQueueDepth	read-only	The average queue size computed and used by the WRED algorithm.
CBQ cbQosREDMeanQSizeUnits	1.3.6.1.4.1.9.9.166.1.20.1.1.25	CbQosQueueUnitType	read-only	Represents the unit type of cbQosREDMeanQSize object.
C32 cbQosREDRandomDropByte	1.3.6.1.4.1.9.9.166.1.20.1.1.5	Counter32	read-only	The lower 32 bits count of bytes dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C64 cbQosREDRandomDropByte64	1.3.6.1.4.1.9.9.166.1.20.1.1.6	Counter64	read-only	The 64 bits count of bytes dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosREDRandomDropByteOverflow	1.3.6.1.4.1.9.9.166.1.20.1.1.4	Counter32	read-only	The upper 32 bits count of bytes dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosREDRandomDropPkt	1.3.6.1.4.1.9.9.166.1.20.1.1.2	Counter32	read-only	The lower 32 bits count of packets dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C64 cbQosREDRandomDropPkt64	1.3.6.1.4.1.9.9.166.1.20.1.1.3	Counter64	read-only	The 64 bits count of packets dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosREDRandomDropPktOverflow	1.3.6.1.4.1.9.9.166.1.20.1.1.1	Counter32	read-only	The upper 32 bits count of packets dropped when the number of packets in the associated queue was greater than the minimum threshold and less than the maximum threshold.
C32 cbQosREDTailDropByte	1.3.6.1.4.1.9.9.166.1.20.1.1.11	Counter32	read-only	The lower 32 bits count of bytes dropped when the number of packets in the associated queue was greater than the maximum threshold.
C64 cbQosREDTailDropByte64	1.3.6.1.4.1.9.9.166.1.20.1.1.12	Counter64	read-only	The 64 bits count of bytes dropped when the number of packets in the associated queue was greater than the maximum threshold.
C32 cbQosREDTailDropByteOverflow	1.3.6.1.4.1.9.9.166.1.20.1.1.10	Counter32	read-only	The upper 32 bits count of bytes dropped when the number of packets in the associated queue was greater than the maximum threshold.
C32 cbQosREDTailDropPkt	1.3.6.1.4.1.9.9.166.1.20.1.1.8	Counter32	read-only	The lower 32 bits count of packets dropped when the number of packets in the associated queue was greater than the maximum threshold.
C64 cbQosREDTailDropPkt64	1.3.6.1.4.1.9.9.166.1.20.1.1.9	Counter64	read-only	The 64 bits count of packets dropped when the number of packets in the associated queue was greater than the maximum threshold.
C32 cbQosREDTailDropPktOverflow	1.3.6.1.4.1.9.9.166.1.20.1.1.7	Counter32	read-only	The upper 32 bits count of packets dropped when the number of packets in the associated queue was greater than the maximum threshold.
C32 cbQosREDTransmitByte	1.3.6.1.4.1.9.9.166.1.20.1.1.17	Counter32	read-only	The lower 32 bits count of octets trasmitted.
C64 cbQosREDTransmitByte64	1.3.6.1.4.1.9.9.166.1.20.1.1.18	Counter64	read-only	The 64 bits count of octets transmitted.
C32 cbQosREDTransmitByteOverflow	1.3.6.1.4.1.9.9.166.1.20.1.1.16	Counter32	read-only	The upper 32 bits count of octets transmitted.
C32 cbQosREDTransmitPkt	1.3.6.1.4.1.9.9.166.1.20.1.1.14	Counter32	read-only	The lower 32 bits count of bytes trasmitted.
C64 cbQosREDTransmitPkt64	1.3.6.1.4.1.9.9.166.1.20.1.1.15	Counter64	read-only	The 64 bits count of packets transmitted.
C32 cbQosREDTransmitPktOverflow	1.3.6.1.4.1.9.9.166.1.20.1.1.13	Counter32	read-only	The upper 32 bits count of bytes transmitted.
I32 cbQosREDValue	1.3.6.1.4.1.9.9.166.1.11.1.1.1	Integer32	not-accessible	The IP precedence or IP DSCP of this entry.
cbQosServicePolicy	1.3.6.1.4.1.9.9.166.1.1
cbQosServicePolicyEntry	1.3.6.1.4.1.9.9.166.1.1.1.1		not-accessible	Each entry in this table describes to which a logical interface a given policymap is attached. Depending on the logical interface/media type, some fields may have meaningful values, and some may not. Please see each individual descriptions.
cbQosServicePolicyExtGroup	1.3.6.1.4.1.9.9.166.2.2.63			Optional objects to provide more information about a particular service policy instance.
cbQosServicePolicyGroup	1.3.6.1.4.1.9.9.166.2.2.1			Required objects to provide CB QoS objects configuration information.
cbQosServicePolicyGroupRev1	1.3.6.1.4.1.9.9.166.2.2.48			Required objects to provide CB QoS objects configuration information. This group deprecates cbQosServicePolicyGroup.
cbQosServicePolicyTable	1.3.6.1.4.1.9.9.166.1.1.1		not-accessible	This table describes the logical interfaces/media types and the policymap that are attached to it.
C64 cbQosSetAtmClpPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.5	Counter64	read-only	The 64 bits count of packets whose ATM CLP Bit is marked by Set feature.
cbQosSetCfg	1.3.6.1.4.1.9.9.166.1.14
cbQosSetCfgDiscardClassGroup	1.3.6.1.4.1.9.9.166.2.2.40			Optional object to provide CB QoS objects configuration information for SET/Marking feature.
U32 cbQosSetCfgDiscardClassValue	1.3.6.1.4.1.9.9.166.1.14.1.1.7	Unsigned32	read-only	The Discard Class value at which the packet is being set by the packet marking feature.
cbQosSetCfgEntry	1.3.6.1.4.1.9.9.166.1.14.1.1		not-accessible	Each entry in this table describes configuration information about a Packet Marking Action. The table holds Packet Marking configuration parameters, such as type of packet marking and values being set to. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex.
SET cbQosSetCfgFeature	1.3.6.1.4.1.9.9.166.1.14.1.1.1	SetFeatureType	read-only	The bit-wise position of each packet marking feature.
T/F cbQosSetCfgFrDe	1.3.6.1.4.1.9.9.166.1.14.1.1.12	TruthValue	read-only	The Discard Eligibility (DE) bit is used to indicate that a frame has lower importance than other frames. The DE bit is part of the Address field in the Frame Relay frame header. DTE devices can set the value of the DE bit of a frame to 1 to indicate that the frame has lower importance than other frames. When the network becomes congested, DCE devices will discard frames with the DE bit set before discarding those that do not. This reduces the likelihood of critical data being dropped by Frame Relay DCE devices during periods of congestion.
cbQosSetCfgFrDeGroup	1.3.6.1.4.1.9.9.166.2.2.73			Optional object to provide CB QoS objects marking configuration information on frame relay header.
U32 cbQosSetCfgFrFecnBecn	1.3.6.1.4.1.9.9.166.1.14.1.1.10	Unsigned32	read-only	This is a configurable parameter in percentage of the queue size. When the current queue size out of the queue limit is greater than this parameter, both Frame Relay FECN and BECN bits will be set for Frame Relay congestion notification mechanism.
cbQosSetCfgFrFecnBecnGroup	1.3.6.1.4.1.9.9.166.2.2.57			Optional object to provide CB QoS SET Frame Relay FECN BECN configuration information.
cbQosSetCfgGroup	1.3.6.1.4.1.9.9.166.2.2.14			Required objects to provide CB QoS objects configuration information.
cbQosSetCfgGroupRev1	1.3.6.1.4.1.9.9.166.2.2.38			Required objects to provide CB QoS objects configuration information for SET/Marking feature.
I32 cbQosSetCfgIpDSCPValue	1.3.6.1.4.1.9.9.166.1.14.1.1.2	Integer32	read-only	The IP DSCP value at which the packet is being set by the packet marking feature.
I32 cbQosSetCfgIpPrecedenceValue	1.3.6.1.4.1.9.9.166.1.14.1.1.3	Integer32	read-only	The IP precedence value at which the packet is being set by the packet marking feature.
I32 cbQosSetCfgL2CosInnerValue	1.3.6.1.4.1.9.9.166.1.14.1.1.11	Integer32	read-only	The value to be set in the 802.1p priority field in the inner 802.1q VLAN tag (QinQ). This object is applicable when cbQosSetCfgFeature has the 'l2CosInner' bit set.
I32 cbQosSetCfgL2CosValue	1.3.6.1.4.1.9.9.166.1.14.1.1.5	Integer32	read-only	The Layer 2 Cos value at which the packet is being set by the packet marking feature.
cbQosSetCfgL2Group	1.3.6.1.4.1.9.9.166.2.2.67			Optional objects to provide CB QoS objects configuration information
U32 cbQosSetCfgMplsExpTopMostValue	1.3.6.1.4.1.9.9.166.1.14.1.1.8	Unsigned32	read-only	The MPLS experimental value on the topmost label at which the packet is being set by the packet marking feature.
U32 cbQosSetCfgMplsExpValue	1.3.6.1.4.1.9.9.166.1.14.1.1.6	Unsigned32	read-only	The MPLS experimental value at which the packet is being set by the packet marking feature.
cbQosSetCfgMplsImpositionGroup	1.3.6.1.4.1.9.9.166.2.2.39			Optional object to provide CB QoS objects configuration information for SET/Marking feature.
cbQosSetCfgMPLSTopMostGroup	1.3.6.1.4.1.9.9.166.2.2.41			Optional object to provide CB QoS objects configuration information for SET/Marking feature.
I32 cbQosSetCfgQosGroupValue	1.3.6.1.4.1.9.9.166.1.14.1.1.4	Integer32	read-only	The QoS Group number at which the packet is being set by the packet marking feature.
U32 cbQosSetCfgSrpPriority	1.3.6.1.4.1.9.9.166.1.14.1.1.9	Unsigned32	read-only	The SRP Priority value at which the packet is being set by the packet marking feature. The higher the value the higher the priority. SRP is a Cisco developed protocol. RFC 2892: The Cisco SRP MAC Layer Protocol.
cbQosSetCfgSrpPriorityGroup	1.3.6.1.4.1.9.9.166.2.2.56			Optional object to provide CB QoS SET SRP Priority configuration information.
cbQosSetCfgTable	1.3.6.1.4.1.9.9.166.1.14.1		not-accessible	This table specifies Packet Marking Action configuration information.
C64 cbQosSetDiscardClassPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.8	Counter64	read-only	The 64 bits count of packets whose Discard Class field is marked by Set feature.
C64 cbQosSetDscpPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.1	Counter64	read-only	The 64 bits count of packets whose DSCP field is marked by Set feature.
C64 cbQosSetDscpTunnelPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.12	Counter64	read-only	The 64 bits count of packets whose DSCP Tunnel field is marked by Set feature.
C64 cbQosSetFrDePkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.4	Counter64	read-only	The 64 bits count of packets whose Frame Relay DE Bit is marked by Set feature.
C64 cbQosSetFrFecnBecnPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.11	Counter64	read-only	The 64 bits count of packets whose Frame Relay FECN BECN field is marked by Set feature.
C64 cbQosSetL2CosPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.6	Counter64	read-only	The 64 bits count of packets whose Layer 2 Cos field is marked by Set feature.
C64 cbQosSetMplsExpImpositionPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.7	Counter64	read-only	The 64 bits count of packets whose MPLS Experimental Imposition field is marked by Set feature.
C64 cbQosSetMplsExpTopMostPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.9	Counter64	read-only	The 64 bits count of packets whose MPLS Experimental TopMost field is marked by Set feature.
C64 cbQosSetPrecedencePkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.2	Counter64	read-only	The 64 bits count of packets whose Precedence field is marked by Set feature.
C64 cbQosSetPrecedenceTunnelPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.13	Counter64	read-only	The 64 bits count of packets whose Precedence Tunnel field is marked by Set feature.
C64 cbQosSetQosGroupPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.3	Counter64	read-only	The 64 bits count of packets whose Qos Group field is marked by Set feature.
C64 cbQosSetSrpPriorityPkt64	1.3.6.1.4.1.9.9.166.1.24.1.1.10	Counter64	read-only	The 64 bits count of packets whose SRP Priority field is marked by Set feature.
cbQosSetStats	1.3.6.1.4.1.9.9.166.1.24
cbQosSetStatsEntry	1.3.6.1.4.1.9.9.166.1.24.1.1		not-accessible	Each entry in this table describes the packets that marked by each marking type. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, namely cbQosPolicyIndex and cbQosObjectsIndex.
cbQosSetStatsGroup	1.3.6.1.4.1.9.9.166.2.2.58			Optional objects to provide CB QoS SET statistical information.
cbQosSetStatsTable	1.3.6.1.4.1.9.9.166.1.24.1		not-accessible	This table specifies packet marking statistical information.
cbQosTableMapCfg	1.3.6.1.4.1.9.9.166.1.26
INT cbQosTableMapCfgBehavior	1.3.6.1.4.1.9.9.166.1.26.1.1.3	INTEGER	read-only	The behavior of a tablemap. value(1) Always set to-value to be a configurable default value which is defined in cbQosTableMapCfgDftValue. copy(2) Always copy from-value to to-value in case the from-value is not found in the tablemap. This is the default behavior for a tablemap. ignore(3) Ignore to set to-value when from-value is not found in the tablemap.
U32 cbQosTableMapCfgDftValue	1.3.6.1.4.1.9.9.166.1.26.1.1.4	Unsigned32	read-only	The configurable default value used when cbQosTableMapCfgBehavior is value(1).
cbQosTableMapCfgEntry	1.3.6.1.4.1.9.9.166.1.26.1.1		not-accessible	Each entry in this table describes configuration information about a tablemap name, behavior and default value. Each cbQosTableMapCfgName is a unique character string in QOS. This table contains configuration information only, no statistics associated with it.
cbQosTableMapCfgGroup	1.3.6.1.4.1.9.9.166.2.2.60			Optional objects to provide CB QoS Enhanced Packet Marking configuration information.
U32 cbQosTableMapCfgIndex	1.3.6.1.4.1.9.9.166.1.26.1.1.1	Unsigned32	not-accessible	An arbitrary (system-assigned) index for tablemap.
STR cbQosTableMapCfgName	1.3.6.1.4.1.9.9.166.1.26.1.1.2	DisplayString	read-only	Name of the tablemap.
cbQosTableMapCfgTable	1.3.6.1.4.1.9.9.166.1.26.1		not-accessible	This table specifies Table Map basic configuration information.
cbQosTableMapSetCfg	1.3.6.1.4.1.9.9.166.1.28
cbQosTableMapSetCfgEntry	1.3.6.1.4.1.9.9.166.1.28.1.1		not-accessible	Each entry in this table describes configuration information for an Enhanced Packet Marking Action. The enhanced packet marking action uses a pre-configured table-map to do the from-value to to-value conversion. The packet marking to-type and from-type relationship can be established by using the table-map. Following is an example: cbQosTMSetIpDscpFromType == qosGroup(3) cbQosTMSetIpDscpMapName == 'MyTableMap', it means that table-map 'MyTableMap' will be used to convert the QosGroup value and the converted value will be used to set IpDSCP. cbQosConfigIndex is drived directly from cbQosSetCfgTable to keep the 1-to-1 mapping between two tables. This table contains configuration information only, no statistics associated with it.
cbQosTableMapSetCfgTable	1.3.6.1.4.1.9.9.166.1.28.1		not-accessible	This table specifies enhanced packet marking configuration using a pre-defined tablemap.
cbQosTableMapValueCfg	1.3.6.1.4.1.9.9.166.1.27
cbQosTableMapValueCfgEntry	1.3.6.1.4.1.9.9.166.1.27.1.1		not-accessible	Each entry in this table specifies a from-value to to-value conversion pair for a given tablemap. This table contains configuration information only, no statistics associated with it.
U32 cbQosTableMapValueCfgFrom	1.3.6.1.4.1.9.9.166.1.27.1.1.1	Unsigned32	not-accessible	This is the from-value in the tablemap. If cbQosTableMapCfgBehavior equals to either copy(2) or ignore(3), when the content in the from-type(e.g., cbQosTMSetIpDscpFromType) equals to this value, the value in the to-type(e.g., IpDscp) will be set to cbQosTableMapValueCfgTo. Each tablemap can configure multiple from-value/to-value pairs.
cbQosTableMapValueCfgTable	1.3.6.1.4.1.9.9.166.1.27.1		not-accessible	This table specifies the from-value to to-value conversion pairs for a tablemap.
U32 cbQosTableMapValueCfgTo	1.3.6.1.4.1.9.9.166.1.27.1.1.2	Unsigned32	read-only	This is the to-value in the tablemap. Its usage is described in cbQosTableMapValueCfgFrom.
CBQ cbQosTMSetIpDscpFromType	1.3.6.1.4.1.9.9.166.1.28.1.1.1	CbQosTMSetType	read-only	The packet marking type whose value will be converted to a to-value based on a pre-configured table-map. The to-value will then be used to set IpDSCP.
STR cbQosTMSetIpDscpMapName	1.3.6.1.4.1.9.9.166.1.28.1.1.2	DisplayString	read-only	The name of a pre-configured table-map used to convert and set IpDSCP value.
CBQ cbQosTMSetIpPrecedenceFromType	1.3.6.1.4.1.9.9.166.1.28.1.1.3	CbQosTMSetType	read-only	The packet marking type whose value will be converted to a to-value based on a pre-configured table-map. The to-value will then be used to set IpPrecedence.
STR cbQosTMSetIpPrecedenceMapName	1.3.6.1.4.1.9.9.166.1.28.1.1.4	DisplayString	read-only	The name of a pre-configured table-map used to convert and set IpPrecedence value.
CBQ cbQosTMSetL2CosFromType	1.3.6.1.4.1.9.9.166.1.28.1.1.7	CbQosTMSetType	read-only	The packet marking type whose value will be converted to a to-value based on a pre-configured table-map. The to-value will then be used to set L2Cos.
STR cbQosTMSetL2CosMapName	1.3.6.1.4.1.9.9.166.1.28.1.1.8	DisplayString	read-only	The name of a pre-configured table-map used to convert and set L2Cos value.
CBQ cbQosTMSetMplsExpImpFromType	1.3.6.1.4.1.9.9.166.1.28.1.1.9	CbQosTMSetType	read-only	The packet marking type whose value will be converted to a to-value based on a pre-configured table-map. The to-value will then be used to set MplsExpImposition.
STR cbQosTMSetMplsExpImpMapName	1.3.6.1.4.1.9.9.166.1.28.1.1.10	DisplayString	read-only	The name of a pre-configured table-map used to convert and set MplsExpImposition value.
CBQ cbQosTMSetMplsExpTopFromType	1.3.6.1.4.1.9.9.166.1.28.1.1.11	CbQosTMSetType	read-only	The packet marking type whose value will be converted to a to-value based on a pre-configured table-map. The to-value will then be used to set MplsExpTopMost.
STR cbQosTMSetMplsExpTopMapName	1.3.6.1.4.1.9.9.166.1.28.1.1.12	DisplayString	read-only	The name of a pre-configured table-map used to convert and set MplsExpTopMost value.
CBQ cbQosTMSetQosGroupFromType	1.3.6.1.4.1.9.9.166.1.28.1.1.5	CbQosTMSetType	read-only	The packet marking type whose value will be converted to a to-value based on a pre-configured table-map. The to-value will then be used to set QosGroup.
STR cbQosTMSetQosGroupMapName	1.3.6.1.4.1.9.9.166.1.28.1.1.6	DisplayString	read-only	The name of a pre-configured table-map used to convert and set QosGroup value.
cbQosTrafficShapingDelayCountersGroup	1.3.6.1.4.1.9.9.166.2.2.18			Optional objects to provide CB QoS traffic-shaping information.
cbQosTSCfg	1.3.6.1.4.1.9.9.166.1.13
T/F cbQosTSCfgAdaptiveEnabled	1.3.6.1.4.1.9.9.166.1.13.1.1.4	TruthValue	read-only	This object indicates is adaptive traffic-shaping has been enabled.
I32 cbQosTSCfgAdaptiveRate	1.3.6.1.4.1.9.9.166.1.13.1.1.5	Integer32	read-only	This object represents the current adaptive traffic shaping rate.
I32 cbQosTSCfgBurstSize	1.3.6.1.4.1.9.9.166.1.13.1.1.2	Integer32	read-only	The amount of traffic, in bits, in excess of the committed traffic-shaping rate that will be instantaneously permitted by this feature.
U32 cbQosTSCfgBurstTime	1.3.6.1.4.1.9.9.166.1.13.1.1.9	Unsigned32	read-only	The amount of traffic, in ms, in excess of the committed traffic-shaping rate that will be instantaneously permitted by this feature. The milli-second value is internally converted to bits by using the bandwidth that is available for the class.
cbQosTSCfgEntry	1.3.6.1.4.1.9.9.166.1.13.1.1		not-accessible	Each entry in this table describes configuration information about a traffic-shaping Action. The table holds Traffic Shaping configuration parameters, such as rate, burst size, and Shaping types. This table contains configuration information only, no statistics associated with it. Therefore, it is indexed by the cbQosConfigIndex.
I32 cbQosTSCfgExtBurstSize	1.3.6.1.4.1.9.9.166.1.13.1.1.3	Integer32	read-only	The amount of traffic, in bits, in excess of the burst limit, which may be conditionally permitted by traffic-shaping feature.
U32 cbQosTSCfgExtBurstTime	1.3.6.1.4.1.9.9.166.1.13.1.1.10	Unsigned32	read-only	The amount of traffic, in ms, in excess of the burst limit, which may be conditionnally permitted by traffic-shaping feature. The milli-second value is internally converted to bits by using the bandwidth that is available for the class.
cbQosTSCfgExtGroup	1.3.6.1.4.1.9.9.166.2.2.65			Objects to provide the information of the committed shaping rate that is greater than the maximum value reportable by cbQosTSCfgRate.
cbQosTSCfgGroup	1.3.6.1.4.1.9.9.166.2.2.13			Required objects to provide CB QoS objects configuration information.
TRA cbQosTSCfgLimitType	1.3.6.1.4.1.9.9.166.1.13.1.1.6	TrafficShapingLimit	read-only	This object indicates if traffic-shaping is limiting traffic based on the peak rate or the average rate.
cbQosTSCfgPercentGroup	1.3.6.1.4.1.9.9.166.2.2.45			Optional objects to provide CB QoS committed traffic-shaping rate in percentage.
U32 cbQosTSCfgPercentRateValue	1.3.6.1.4.1.9.9.166.1.13.1.1.8	Unsigned32	read-only	The committed traffic-shaping rate in percentage. Its value is valid only when cbQosTSCfgRateType equals to 2.
I32 cbQosTSCfgRate	1.3.6.1.4.1.9.9.166.1.13.1.1.1	Integer32	read-only	The committed traffic-shaping rate. This is the sustained rate permitted by the traffic-shaping.
UNS cbQosTSCfgRate64	1.3.6.1.4.1.9.9.166.1.13.1.1.11	Unsigned64	read-only	The committed shape rate. This is the sustained rate permitted by shaping. This object represents the 64 bit value of object cbQosTSCfgRate
CBQ cbQosTSCfgRateType	1.3.6.1.4.1.9.9.166.1.13.1.1.7	CbQosRateType	read-only	The rate type that configured for traffic-shaping. 1 means rate is configured in bps. 2 means rate is configured in percentage.
cbQosTSCfgTable	1.3.6.1.4.1.9.9.166.1.13.1		not-accessible	This table specifies traffic-shaping Action configuration information.
cbQosTSCfgTimeGroup	1.3.6.1.4.1.9.9.166.2.2.55			Optional objects to provide CB QoS traffic-shaping time based burst size configuration information.
cbQosTSStats	1.3.6.1.4.1.9.9.166.1.19
T/F cbQosTSStatsActive	1.3.6.1.4.1.9.9.166.1.19.1.1.13	TruthValue	read-only	This object indicates the current traffic-shaping state. When traffic-shaping is enabled and the traffic rate exceeds the shape rate, traffic-shaping is considered to be active. Otherwise, it is considered inactive.
G32 cbQosTSStatsCurrentQSize	1.3.6.1.4.1.9.9.166.1.19.1.1.14	Gauge32	read-only	This object indicates the current traffic-shaping queue depth in packets.
C32 cbQosTSStatsDelayedByte	1.3.6.1.4.1.9.9.166.1.19.1.1.2	Counter32	read-only	This object represents the lower 32 bits counter of octets that have been delayed.
C64 cbQosTSStatsDelayedByte64	1.3.6.1.4.1.9.9.166.1.19.1.1.3	Counter64	read-only	This object represents the 64 bits counter of octets that have been delayed.
C32 cbQosTSStatsDelayedByteOverflow	1.3.6.1.4.1.9.9.166.1.19.1.1.1	Counter32	read-only	This object represents the upper 32 bits counter of octets that have been delayed.
C32 cbQosTSStatsDelayedPkt	1.3.6.1.4.1.9.9.166.1.19.1.1.5	Counter32	read-only	This object represents the lower 32 bits counter of packets that have been delayed.
C64 cbQosTSStatsDelayedPkt64	1.3.6.1.4.1.9.9.166.1.19.1.1.6	Counter64	read-only	This object represents the 64 bits counter of packets that have been delayed.
C32 cbQosTSStatsDelayedPktOverflow	1.3.6.1.4.1.9.9.166.1.19.1.1.4	Counter32	read-only	This object represents the upper 32 bits counter of packets that have been delayed.
C32 cbQosTSStatsDropByte	1.3.6.1.4.1.9.9.166.1.19.1.1.8	Counter32	read-only	This object represents the lower 32 bits counter of octets that have been dropped during shaping.
C64 cbQosTSStatsDropByte64	1.3.6.1.4.1.9.9.166.1.19.1.1.9	Counter64	read-only	This object represents the 64 bits counter of octets that have been dropped during shaping.
C32 cbQosTSStatsDropByteOverflow	1.3.6.1.4.1.9.9.166.1.19.1.1.7	Counter32	read-only	This object represents the upper 32 bits counter of octets that have been dropped during shaping.
C32 cbQosTSStatsDropPkt	1.3.6.1.4.1.9.9.166.1.19.1.1.11	Counter32	read-only	This object represents the lower 32 bits counter of packets that have been dropped during shaping.
C64 cbQosTSStatsDropPkt64	1.3.6.1.4.1.9.9.166.1.19.1.1.12	Counter64	read-only	This object represents the 64 bits counter of packets that have been dropped during shaping.
C32 cbQosTSStatsDropPktOverflow	1.3.6.1.4.1.9.9.166.1.19.1.1.10	Counter32	read-only	This object represents the upper 32 bits counter of packets that have been dropped during shaping.
cbQosTSStatsEntry	1.3.6.1.4.1.9.9.166.1.19.1.1		not-accessible	Each entry in this table describes the statistical information about traffic-shaping Action. Traffic-shaping Action specific information you can find in this table are : various delay/drop pkt/byte counters, state of feature, and Q size. This table contains statistical information only, no configuration information associated with it. Therefore, it is indexed by the instance specific IDs, such as cbQosPolicyIndex and cbQosObjectsIndex.
cbQosTSStatsGroup	1.3.6.1.4.1.9.9.166.2.2.22			Required objects to provide CB QoS objects configuration information.
cbQosTSStatsTable	1.3.6.1.4.1.9.9.166.1.19.1		not-accessible	This table specifies traffic-shaping Action related Statistical information.
VLA cbQosVlanIndex	1.3.6.1.4.1.9.9.166.1.1.1.1.9	VlanIndex	read-only	If the service policy is attached to a particular vlan on a trunk or multi-vlan access port, then this object specifies the corresponding VLAN. In all other cases the value of this object is '0'.
ciscoCBQosMIB	1.3.6.1.4.1.9.9.166			Cisco Class-Based QoS MIB ******************************** Overview ****************************** This MIB provides read access to Quality of Service (QoS) configuration and statistics information for Cisco platforms that support the Modular Quality of Service Command-line Interface (Modular QoS CLI). We recommend users of this MIB to review the user documentation of MQC based QoS features. Configuration information available through this MIB includes all ClassMap, PolicyMap, Match Statements, and Feature Actions configuration parameters. The definitions of each objects mentioned above are explained in the QoS objects section. Statistics available through this MIB include summary counts/rates by traffic class before and after any configured QoS policies are enforced. In addition, detailed feature-specific statistics are available for select PolicyMap features. Contact your Cisco representative to determine on which platforms the MIB is currently supported. ****************************** QoS Acronyms ****************************** BECN: Frame Relay Backward Explicit Congestion Notification CIR : Committed Information Rate DSCP: Differentiated Service Code Point EB : Estimate Bandwidth ECN : Explicite Congestion Notification FECN: Frame Relay Forward Explicit Congestion Notification IPHC: Internet Protocol Header Compression IPSLAs: IP Service Level Agreement Technologies PIR : Peak Information Rate PREC: Precedence QoS : Quality Of Services RED : Random Early Detect SRP : Spatial Reuse Protocol WRED: Weighted Random Early Detect C3PL: Cisco Common Classification Programming Language ****************************** MIB Objects ****************************** This MIB consists of the following object groups: 1 : cbQosServicePolicy 2 : cbQosInterfacePolicy 3 : cbQosFrameRelayVCPolicy 4 : cbQosATMPVCPolicy 5 : cbQosObjects 6 : cbQosPolicyMapCfg 7 : cbQosClassMapCfg 8 : cbQosMatchStmtCfg 9 : cbQosQueueingCfg 10: cbQosREDCfg 11: cbQosREDClassCfg 12: cbQosPoliceCfg 13: cbQosTSCfg 14: cbQosSetCfg 15: cbQosClassMapStats 16: cbQosMatchStmtStats 17: cbQosPoliceStats 18: cbQosQueueingStats 19: cbQosTSStats 20: cbQosREDClassStats 21: cbQosPoliceActionCfg 22: cbQosIPHCCfg 23: cbQosIPHCStats 24: cbQosSetStats 25: cbQosPoliceColorStats 26: cbQosTableMapCfg 27: cbQosTableMapValueCfg 28: cbQosTableMapSetCfg 29: cbQosEBCfg 30: cbQosEBStats 31: cbQosMeasureIPSLACfg 32: cbQosC3plAccountCfg 33: cbQosC3plAccountStats ****************************** Definitions ****************************** A logical interface in the context of this MIB is either a main-interface, a sub-interface, a Frame Relay DLCI, an ATM virtual circuit or the control-plane on the router. The (aggregate) control-plane on the router is defined as a collection of processes running at process level on the platform (route) processor. This includes the functions related to networking control capabilities such as routing, signaling, provisioning, as well as resource and service discovery. Also includes process switched traffic on the device. The term distributed control plane, in the context of this mib, represents the control-plane functionality at the level of individual linecards. This is only applicable for the case of distributed platforms. ****************************** QoS Objects ****************************** To understand Class-Based QoS features and how to navigate the MIB tables above, the key element is to comprehend the relationships among the different QoS objects. QoS objects consist of ClassMaps, Match Statements and PolicyMaps, and each Feature Actions. Match Statement - The specific match criteria to identify packets for classification purposes. ClassMap - A user-defined traffic class that contains one or many match statements used to classify packets into different categories. Feature Action - An action is a QoS feature. Features include police, traffic-shaping, queueing, random detect and packet marking(set). After the traffic is being classified, based on the traffic classification, we can apply these action to each traffic class. PolicyMap - A user-defined policy that associates each QoS action to the user-defined traffic class (ClassMap). Service Policy - Service policy is a policymap that is being attached to a logical interface. Because a policymap can also be a part of the hierarchical structure (inside a classmap), only a policymap that is directly attached to a logical interface is considered a service policy. Each service policy is uniquely identified by an index called cbQosPolicyIndex. This number is usually identical to its cbQosObjectsIndex as a policymap. ************************************* Runtime Instance vs Configuration objects ************************************* Each QoS objects have 2 sets of behaviours : 1: A configuration instance - Each QoS objects has it's configuration portion of information attached to it. This information does not change whether this object is attached on multiple logical interfaces and used multiple times. We uniquely identify each QoS object with identical configuration with the same index - cbQosConfigIndex. This index is used in all configuration related tables. 2: A runtime instance - Each QoS objects has it's statistical portion of information attached to it. This information changes when this object is attached on multiple logical interfaces and used in various different places. We uniquely identify each QoS runtime object instance with an index that is unique across multiple instances of the identical object - cbQosObjectsIndex. This index is used in all statistical related tables. In summary, a QoS object has 2 indexes associated with it: cbQosConfigIndex is used to identify it's configuration, which does not change regardless of number of times and where it is being used; and cbQosObjectsIndex is used to identify it's runtime statistics, depending on which logical interface and where in a given PolicyMap hierarchy this object is used, it may have multiple unique identifiers to distinguish each unique usage (instance) of the same object. ****************************** Navigation ****************************** The recommended method of navigating through all of the MIB tables is to start by learning the cbQosServicePolicyTable and cbQosObjectsTable MIB tables. In particular, Cisco Systems recommends understanding the cbQosObjectsIndex and cbQosParentObjectsIndex of each QoS feature. The cbQosPolicyIndex and cbQosObjectsIndex are system-assigned numbers that identify each unique instance of a QoS feature. These indexes are never reused between router reboots, even when changes are made to the QoS configuration. The cbQosPolicyIndex is designed to identify the service policies attached to logical interfaces, while the cbQosObjectsIndex is designed to identify each QoS feature on a specified device. The cbQosParentObjectsIndex is designed to show the hierarchical relationship of each QoS feature. ****************************** cbQosServicePolicyTable ****************************** Accessing cbQosServicePolicyTable requires cbQosPolicyIndex. This index is a system-assigned number to uniquely identify each service policy hanging off of each logical interface. Given cbQosPolicyIndex the tables provide the type of logical interface/media type on which this policy is applied, the direction in which this policy is enforced, and the SNMP interface index and/or the entity index of the underlying interface/entity. In the case of a policy being applied on a Frame Relay DLCI, the cbQosFrDLCI gives you the Frame Relay DLCI number to which this policy is attached. In the case of policy being attached to an ATM VC, cbQosAtmVPI and cbQosAtmVCI display the VPI and VCI of the ATM interface respectively. ****************************** cbQosObjectsTable ****************************** Accessing cbQosObjectsTable requires two indexes, cbQosPolicyIndex and cbQosObjectsIndex. Given a particular service policy on a given logical interface, there could be PolicyMaps, ClassMaps, Match Statements and Feature Actions being used. Each instance of these objects is uniquely identified by cbQosObjectsIndex. Users need to decide which QoS object is interesting and use the cbQosPolicyIndex and cbQosObjectsIndex to locate the right element of interest. This tables provides cbQosObjectsType, cbQosConfigIndex, and cbQosParentObjectsIndex. To understand the relationship of cbQosObjectsIndex, cbQosParentObjectsIndex and the hierarchical relationship of the QoS objects, consider the following QoS configuration example: Interface ethernet 0/1 Input Service Policy cntlWebTraffic ClassMap http match ip http set ip precedence 5 Output Service Policy cntlSNMP_Telnet ClassMap snmp match ip snmp shape average 8000 32 32 ClassMap Telnet match ip telnet shape average 10000 32 32 Interface ethernet 0/2 Input Service Policy cntlWebTraffic ClassMap http match ip http set ip precedence 5 Output Service Policy cntlSNMP_Telnet ClassMap snmp match ip snmp shape average 8000 32 32 ClassMap Telnet match ip telnet shape average 10000 32 32 * In Ethernet 0/1 * Assume the router assigned a cbQosConfigIndex=1024 and cbQosObjectsIndex=1084 to Policy cntlWebTraffic. Because it is attached to an interface, it has no parent QoS object, and thus cbQosParentObjectsIndex=0. In addition, because cntlWebTraffic is also the service policy of the interface, it has a unique cbQosPolicyIndex assigned to it. In most cases, it would be the same as the cbQosObjectsIndex, which is 1084 in this case. Therefore, the indexes are: cbQosPolicyIndex = 1084 cbQosObjectsIndex = 1084 cbQosConfigIndex = 1024 Assuming the router assigned a cbQosObjectsIndex=1085 and cbQosConfigIndex=1025 to ClassMap http, it is directly being used by Policy cntlWebTraffic, and therefore the cbQosParentObjectsIndex of ClassMap http will be 1084. Assuming the router assigned a cbQosConfigIndex=1026 and cbQosObjectsIndex=1086 to match ip http, it is directly used by ClassMap http, therefore the cbQosParentObjectsIndex of match ip http will be 1085. Assuming the router assigned a cbQosConfigIndex=1027 and cbQosObjectsIndex=1087 to set ip precedence 5, it is directly used by ClassMap http, therefore the cbQosParentObjectsIndex of match ip http will be 1085. Assuming the router assigned a cbQosConfigIndex=1028 and cbQosObjectsIndex=1088 to Policy cntlSNMP_Telnet. Because it is attached to an interface, it has no parent QoS object, and thus cbQosParentObjectsIndex=0. In addition, because cntlSNMP_Telnet is also the service policy of the interface, it has a unique cbQosPolicyIndex assigned to it. In most cases, it would be the same as the cbQosObjectsIndex, which is 1088 in this case. Assuming the router assigned a cbQosConfigIndex=1029 and cbQosObjectsIndex=1089 to ClassMap snmp, it is directly being used by Policy cntlSNMP_Telnet, and therefore the cbQosParentObjectsIndex of ClassMap snmp will be 1088. Assuming the router assigned a cbQosConfigIndex=1030 and cbQosObjectsIndex=1090 to match ip snmp, it is directly used by ClassMap snmp, and therefore the cbQosParentObjectsIndex of match ip snmp will be 1089. Assuming the router assigned a cbQosConfigIndex=1031 and cbQosObjectsIndex=1091 to shape average 8000 32 32, it is directly used by ClassMap snmp, therefore the cbQosParentObjectsIndex of match ip snmp will be 1089. Assuming the router assigned a cbQosConfigIndex=1032 and cbQosObjectsIndex=1092 to ClassMap Telnet, it is directly being used by Policy cntlSNMP_Telnet, and therefore the cbQosParentObjectsIndex of ClassMap Telnet will be 1088. Assuming the router assigned a cbQosConfigIndex=1033 and cbQosObjectsIndex=1093 to match ip telnet, it is directly used by ClassMap Telnet, and therefore the cbQosParentObjectsIndex of match ip telnet will be 1092. Assuming the router assigned a cbQosConfigIndex=1034 and cbQosObjectsIndex=1094 to shape 10000 32 32, it is directly used by ClassMap telnet, therefore the cbQosParentObjectsIndex of match ip telnet will be 1092. * In Ethernet 0/2 * Every objects will have a new and unique cbQosPolicyIndex and cbQosObjectsIndex, but cbQosConfigIndex will be shared across the same objects that are applied in different places. ****************************** All Config Tables ****************************** Accessing config related tables requires the same index - cbQosConfigIndex. (Per precedence based tables requires a second index, which is IP precedence value) Users should have already gone through the cbQosObjectsTable at this point and understood each cbQosConfigIndex and the corresponding QoS objects. Users can uniquely identify each QoS object defined on the router and query the entries in each stats table on a per QoS object basis. ****************************** All Stats Tables ******************************** Accessing all stats related tables requires the same 2 indexes. They are cbQosPolicyIndex and cbQosObjectsIndex. (Per precedence based tables requires a third index, which is IP precedence value) Users should have already gone through the cbQosObjectsTable at this point and understood the relationship of each cbQosPolicyIndex and cbQosObjectsIndex pair and the corresponding QoS objects. Users can uniquely identify each QoS object defined on the router and query the entries in each stats table on a per QoS object basis.
ciscocbQosMIBCompliance	1.3.6.1.4.1.9.9.166.2.1.1			The compliance statement for entities that implement class-based QoS on a Cisco router.
ciscocbQosMIBComplianceRev1	1.3.6.1.4.1.9.9.166.2.1.2			The compliance statement for entities that implement class-based QoS on a Cisco router. This compliance module deprecates ciscocbQosMIBCompliance.
ciscocbQosMIBComplianceRev2	1.3.6.1.4.1.9.9.166.2.1.3			The compliance statement for entities that implement class-based QoS on a Cisco router. This compliance module deprecates ciscocbQosMIBComplianceRev1.
ciscocbQosMIBComplianceRev3	1.3.6.1.4.1.9.9.166.2.1.4			The compliance statement for entities that implement class-based QoS on a Cisco router. This compliance module deprecates ciscocbQosMIBComplianceRev2.
ciscocbQosMIBComplianceRev4	1.3.6.1.4.1.9.9.166.2.1.5			The compliance statement for entities that implement class-based QoS on a Cisco router. This compliance module deprecates ciscocbQosMIBComplianceRev2.
ciscocbQosMIBComplianceRev5	1.3.6.1.4.1.9.9.166.2.1.6			The compliance statement for entities that implement class-based QoS on a Cisco router. This compliance module deprecates ciscocbQosMIBComplianceRev4.
ciscocbQosMIBComplianceRev6	1.3.6.1.4.1.9.9.166.2.1.7			The compliance statement for entities that implement class-based QoS on a Cisco router. This compliance module deprecates ciscocbQosMIBComplianceRev5.
ciscocbQosMIBComplianceRev7	1.3.6.1.4.1.9.9.166.2.1.8			The compliance statement for entities that implement class-based QoS on a Cisco router. This compliance module deprecates ciscocbQosMIBComplianceRev5.
ciscocbQosMIBComplianceRev8	1.3.6.1.4.1.9.9.166.2.1.9			The compliance statement for entities that implement class-based QoS on a Cisco router. This compliance module deprecates ciscocbQosMIBComplianceRev7.
ciscocbQosMIBCompliances	1.3.6.1.4.1.9.9.166.2.1
ciscocbQosMIBConformance	1.3.6.1.4.1.9.9.166.2
ciscocbQosMIBGroups	1.3.6.1.4.1.9.9.166.2.2
ciscoCBQosMIBObjects	1.3.6.1.4.1.9.9.166.1

RFC description

Cisco Quality of Service configuration and statistics using Modular QoS CLI, including class maps and policy enforcement.

Start monitoring Cisco routers and switches (class-based QoS) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-CLASS-BASED-QOS-MIB

What Is CISCO-CLASS-BASED-QOS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description