| OID symbolic | OID numeric | Type | Access | Description |
|---|
| cerentOpticalMonitorMIB | 1.3.6.1.4.1.3607.1.10.70 | | | This MIB module defines objects to monitor optical
characteristics and set corresponding thresholds, on the
optical interfaces in a network element.
This module is an adaptation of CISCO-OPTICAL-MONITOR-MIB. |
| cerentOpticalMonitorMIBObjects | 1.3.6.1.4.1.3607.2.30 | | | |
| cerentOpticalMonGroup | 1.3.6.1.4.1.3607.2.30.1 | | | |
| cOpticalMonTable | 1.3.6.1.4.1.3607.2.30.1.1 | | not-accessible | This table provides objects to monitor optical
parameters in a network element. It also provides
objects for setting high and low threshold levels, with
configurable severities, on these monitored parameters. |
| cOpticalMonEntry | 1.3.6.1.4.1.3607.2.30.1.1.1 | | not-accessible | An entry in the cOpticalMonTable provides objects to
monitor an optical parameter and set threshold levels
on that parameter, at an optical interface.
Note that the set of monitored optical parameters may vary
based on interface type and direction.
Examples of interfaces that can have an entry in this table
include optical transceivers optical amplifiers,
and optical attenuators. |
| OPT cOpticalMonDirection | 1.3.6.1.4.1.3607.2.30.1.1.1.1 | OpticalIfDirection | not-accessible | This object is an index into the cOpticalMonTable
and indicates the direction monitored for the
optical interface, in this entry. |
| OPT cOpticalMonParameterType | 1.3.6.1.4.1.3607.2.30.1.1.1.2 | OpticalParameterType | not-accessible | This object is an index into the cOpticalMonTable
and specifies the optical parameter that is being monitored,
in this entry. |
| OPT cOpticalParameterValue | 1.3.6.1.4.1.3607.2.30.1.1.1.3 | OpticalParameterValue | read-only | This object gives the value measured for the particular
optical parameter specified by the cOpticalMonParameterType
object. |
| OPT cOpticalParamHighAlarmThresh | 1.3.6.1.4.1.3607.2.30.1.1.1.4 | OpticalParameterValue | read-write | This object is used to set a high alarm threshold on the
optical parameter being monitored.
If the measured value of the parameter,is greater than the
value configured in this object, an alarm will be raised.
When the cOpticalMonParameterType object is set to 'power'
for the receive direction at a transceiver, this object
specifies the receiver saturation level. |
| OPT cOpticalParamHighWarning15MinThresh | 1.3.6.1.4.1.3607.2.30.1.1.1.5 | OpticalParameterValue | read-write | This object is used to set a high warning 15 minute threshold
on the optical parameter being monitored.
If the measured value of the parameter,is greater than the
value configured in this object, an alarm may be raised. |
| OPT cOpticalParamHighWarning1DayThresh | 1.3.6.1.4.1.3607.2.30.1.1.1.6 | OpticalParameterValue | read-write | This object is used to set a high warning 1 day threshold on
the optical parameter being monitored.
If the measured value of the parameter,is greater than the
value configured in this object, an alarm may be raised. |
| OPT cOpticalParamLowAlarmThresh | 1.3.6.1.4.1.3607.2.30.1.1.1.7 | OpticalParameterValue | read-write | This object is used to set a low alarm threshold on the
optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, an alarm will be raised.
When the cOpticalMonParameterType object is set to 'power'
for the receive direction and when the interface supports
alarms based on loss of light, this object specifies the
optical power threshold for declaring loss of light. Also,
when optical amplifiers are present in the network, in the
receive direction, this value may need to be configured,
since the noise floor may be higher than the minimum
sensitivity of the receiver. |
| OPT cOpticalParamLowWarning15MinThresh | 1.3.6.1.4.1.3607.2.30.1.1.1.8 | OpticalParameterValue | read-write | This object is used to set a low warning 15 minute threshold
on the optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, an alarm will be raised. |
| OPT cOpticalParamLowWarning1DayThresh | 1.3.6.1.4.1.3607.2.30.1.1.1.9 | OpticalParameterValue | read-write | This object is used to set a low warning 1 day threshold
on the optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, an alarm will be raised. |
| OPT cOpticalParamLowDegradeThresh | 1.3.6.1.4.1.3607.2.30.1.1.1.10 | OpticalParameterValue | read-write | This object is used to set a low degrade threshold
on the optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, a degrade alarm will be raised. |
| OPT cOpticalParamHighDegradeThresh | 1.3.6.1.4.1.3607.2.30.1.1.1.11 | OpticalParameterValue | read-write | This object is used to set a high degrade threshold
on the optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, a degrade alarm will be raised. |
| cerentOpticalPMGroup | 1.3.6.1.4.1.3607.2.30.2 | | | |
| cOpticalPMCurrentTable | 1.3.6.1.4.1.3607.2.30.2.1 | | not-accessible | This table stores performance monitoring data for the
various optical parameters, collected over the current
interval. |
| cOpticalPMCurrentEntry | 1.3.6.1.4.1.3607.2.30.2.1.1 | | not-accessible | An entry in the cOpticalPMCurrentTable. It contains
performance monitoring data for an optical parameter,
collected over the current interval.
Note that the set of monitored optical parameters may vary
based on interface type and direction.
Examples of interfaces that can have an entry in this table
include optical transceivers, optical amplifiers, and optical
attenuators. |
| OPT cOpticalPMCurrentDirection | 1.3.6.1.4.1.3607.2.30.2.1.1.1 | OpticalIfDirection | not-accessible | This object is an index into the cOpticalPMCurrentTable
and indicates the direction monitored
for the optical interface, in this entry. |
| OPT cOpticalPMCurrentParamType | 1.3.6.1.4.1.3607.2.30.2.1.1.2 | OpticalParameterType | not-accessible | This object is an index into the
cOpticalPMCurrentTable and specifies the optical parameter
that is being monitored, in this entry. |
| CER cOpticalPMCurrentPeriod | 1.3.6.1.4.1.3607.2.30.2.1.1.3 | CerentPeriod | not-accessible | This object is an index into the
cOpticalPMCurrentTable and indicates whether the
optical parameter values given in this entry, are collected
over a period of 15 minutes or 24 hours. |
| OPT cOpticalPMCurrentMaxParam | 1.3.6.1.4.1.3607.2.30.2.1.1.4 | OpticalParameterValue | read-only | This object gives the maximum value measured for the optical
parameter, in the current 15 minute or 24 hour interval. |
| OPT cOpticalPMCurrentMinParam | 1.3.6.1.4.1.3607.2.30.2.1.1.5 | OpticalParameterValue | read-only | This object gives the minimum value measured for the optical
parameter, in the current 15 minute or 24 hour interval. |
| OPT cOpticalPMCurrentMeanParam | 1.3.6.1.4.1.3607.2.30.2.1.1.6 | OpticalParameterValue | read-only | This object gives the average value of the measured optical
parameter, in the current 15 minute or 24 hour interval. |
| cOpticalPMIntervalTable | 1.3.6.1.4.1.3607.2.30.2.2 | | not-accessible | This table stores performance monitoring data for the
various optical parameters, collected over current and
previous intervals.
This table can have entries for up to 96 complete 15 minute
intervals. |
| cOpticalPMIntervalEntry | 1.3.6.1.4.1.3607.2.30.2.2.1 | | not-accessible | An entry in the cOpticalPMIntervalTable. It contains
performance monitoring data for an optical parameter,
collected over current and previous intervals.
Note that the set of monitored optical parameters may vary
based on interface type and direction.
Examples of interfaces that can have an entry in this table
include optical transceivers, optical amplifiers, and optical
attenuators. |
| OPT cOpticalPMIntervalDirection | 1.3.6.1.4.1.3607.2.30.2.2.1.1 | OpticalIfDirection | not-accessible | This object is an index into the cOpticalPMIntervalTable
and indicates the direction monitored
for the optical interface, in this entry. |
| OPT cOpticalPMIntervalParamType | 1.3.6.1.4.1.3607.2.30.2.2.1.2 | OpticalParameterType | not-accessible | This object is an index into the
cOpticalPMIntervalTable and specifies the optical parameter
that is being monitored, in this entry. |
| CER cOpticalPMIntervalPeriod | 1.3.6.1.4.1.3607.2.30.2.2.1.3 | CerentPeriod | not-accessible | This object is an index into the
cOpticalPMIntervalTable and indicates whether the
optical parameter values given in this entry, are collected
over a period of 15 minutes or 24 hours. |
| I32 cOpticalPMIntervalNumber | 1.3.6.1.4.1.3607.2.30.2.2.1.4 | Integer32 | not-accessible | This object is an index into the cOpticalPMIntervalTable.
It is a number between 1 and 96, which identifies the
interval for which the set of optical parameter values is
available. The interval identified by 1 is the most recent
15 minute or 24 hour interval, and the interval
identified by N is the interval immediately preceding the one
identified by N-1. |
| OPT cOpticalPMIntervalMaxParam | 1.3.6.1.4.1.3607.2.30.2.2.1.5 | OpticalParameterValue | read-only | This object gives the maximum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval. |
| OPT cOpticalPMIntervalMinParam | 1.3.6.1.4.1.3607.2.30.2.2.1.6 | OpticalParameterValue | read-only | This object gives the minimum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval. |
| OPT cOpticalPMIntervalMeanParam | 1.3.6.1.4.1.3607.2.30.2.2.1.7 | OpticalParameterValue | read-only | This object gives the average value of the measured optical
parameter, in a particular 15 minute or 24 hour interval. |
| T/F cOpticalPMIntervalValidData | 1.3.6.1.4.1.3607.2.30.2.2.1.8 | TruthValue | read-only | This variable indicates if the data for this
interval is valid. |
| cerentOpticalMonitorMIBConformance | 1.3.6.1.4.1.3607.5.20 | | | |
| cerentOpticalMonitorMIBCompliances | 1.3.6.1.4.1.3607.5.20.1 | | | |
| cerentOpticalMonitorMIBCompliance | 1.3.6.1.4.1.3607.5.20.1.1 | | | The compliance statement for network elements that
monitor optical characteristics and set thresholds on the
optical interfaces in a network element. |
| cerentOpticalMonitorMIBGroups | 1.3.6.1.4.1.3607.5.20.2 | | | |
| cerentOpticalMIBMonGroup | 1.3.6.1.4.1.3607.5.20.2.1 | | | A mandatory object that provides monitoring of optical
characteristics. |
| cerentOpticalMIBThresholdGroup | 1.3.6.1.4.1.3607.5.20.2.2 | | | A collection of objects that support thresholds on optical
parameters and provide status information when the thresholds
are exceeded or cleared. |
| cerentOpticalMIBPMGroup | 1.3.6.1.4.1.3607.5.20.2.3 | | | A collection of objects that provide optical performance
monitoring data for 15 minute and 24 hour intervals. |
| cerentOpticalDwdmNetworkMIBThresholdGroup | 1.3.6.1.4.1.3607.5.20.2.4 | | | A collection of objects that support thresholds on optical
DWDM Network parameters and provide status information when
the thresholds are exceeded or cleared. |
