ACP-MIB

All MIBs › ACP-MIB

Organization: Motorola

Last Updated: 2003-06-10

Category: Optical and WDM

Description: Manages Appian Communications optical networking equipment, providing configuration and performance monitoring for WDM transport systems.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ACP-MIB?

ACP-MIB is a vendor-specific MIB for the Access Control Processor (referred to as TSODA/MC1) within Appian Communications' optical WDM transport equipment, managing per-service encryption/scrambling and access authorization on optical channels. It exposes a status table (acpStatusTable) covering per-unit and per-service parameters such as encryption type (acpEncryptType), scrambling mode (acpScramblingMode), unit address, and mapped input/output interfaces, plus service authorization objects (acpServAuthorization, acpServAuthReaCode). This MIB is centered on service-level configuration and authorization status monitoring rather than classic hardware sensors, an operator uses it to confirm whether individual optical services are authorized and correctly secured (encrypted/scrambled) end-to-end, and to trace which physical input/output interface each service maps to. It is part of Appian's optical transport MIB suite and would typically be used alongside other optical-performance MIBs covering the underlying WDM transport layer. Typical deployment is on Appian Communications WDM optical transport network elements used by carriers for metro/regional optical networking. Engineers can download the ACP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ACP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Motorola TSODA/MC1 Access Control Processor equipment (legacy telecom access system)

Monitoring Examples

An operator would poll acpStatusTable / acpStatusEntry indexed by acpUnitIndex and acpServiceIndex to check acpEncryptType and acpScramblingMode for a given service, confirming that a service expected to be encrypted actually shows the correct encryption type rather than none. Checking acpServAuthorization together with acpServAuthReaCode for a service would reveal whether that service is authorized, and if not, the reason code for denial. Cross-referencing acpInputInterface and acpOutputInterface would confirm the service is mapped through the correct optical ports.

What Can Be Monitored

per-service encryption type
scrambling mode
service authorization status
authorization reason code
input/output interface mapping

Imported Objects

From BCS-IDENT-MIB

giproducts

OBJECT-IDENTITY

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
acpStatus	1.3.6.1.4.1.1166.1.11			The MIB module for the Access Control Processor (TSODA, MC1). Revision Number 1.40
INT acpNumberofEncryptTypes	1.3.6.1.4.1.1166.1.11.1	INTEGER	read-only	The total number of encrypt type ACPs in the system.
INT acpNumberofDecryptTypes	1.3.6.1.4.1.1166.1.11.2	INTEGER	read-only	The total number of decrypt type ACPs in the system.
acpStatusTable	1.3.6.1.4.1.1166.1.11.3		not-accessible	A table of ACP entries giving health, status and mode
acpStatusEntry	1.3.6.1.4.1.1166.1.11.3.1		not-accessible	A row in the ACP Entry Table
INT acpEncryptType	1.3.6.1.4.1.1166.1.11.3.1.1	INTEGER	not-accessible	The type of ACP in the system. It is either an encryptAcp or decryptAcp device.
INT acpUnitIndex	1.3.6.1.4.1.1166.1.11.3.1.2	INTEGER	not-accessible	The ACP unit index for this encrypt/decrypt type. For each type of ACP, encryptAcp or decryptAcp, the physical unit number of the ACP in the containing product, starting at 1.
INT acpServiceIndex	1.3.6.1.4.1.1166.1.11.3.1.3	INTEGER	not-accessible	For a specified ACP, identified by the both acpEncryptType and acpUnitIndex, this index specifies the sequential service capabilities of this ACP, found in the following objects: acpServNumber acpServAuthorization acpServAuthReaCode acpServEncryption The maximum limit on the value of this index is determined by the Max number of services supported by this ACP (for a TSODA, it is 2). For all other objects in the acpStatusTable, this index is not used. (it must be valid, but will not be used to access the object uniquely specified by acpEncryptType and acpUnitIndex) REFERENCE
INT acpScramblingMode	1.3.6.1.4.1.1166.1.11.3.1.4	INTEGER	read-only	The Scrambling Mode of the ACP 1 - North American DES 2 - DVB Common Scrambling Algorithm
OCT acpUnitAddress	1.3.6.1.4.1.1166.1.11.3.1.5	OCTET STRING	read-only	The 40 bit ACP address in Human-readable format 3-5-5-3
INT acpInputInterface	1.3.6.1.4.1.1166.1.11.3.1.6	INTEGER	read-only	The interface for MPEG input to this ACP.
INT acpOutputInterface	1.3.6.1.4.1.1166.1.11.3.1.7	INTEGER	read-only	The interface for MPEG output from this ACP.
INT acpServNumber	1.3.6.1.4.1.1166.1.11.3.1.8	INTEGER	read-only	MPEG service number (0=unknown) for encrypted service N, where N is specified by acpServiceIndex.
INT acpServAuthorization	1.3.6.1.4.1.1166.1.11.3.1.9	INTEGER	read-only	ACP authorization status for service specified by acpServiceIndex
INT acpServAuthReaCode	1.3.6.1.4.1.1166.1.11.3.1.10	INTEGER	read-only	ACP authorization reason code for service specified By acpServiceIndex.
INT acpServEncryption	1.3.6.1.4.1.1166.1.11.3.1.11	INTEGER	read-only	ACP encryption status for service specified by The index acpServiceIndex.
INT acpCatSeqNums	1.3.6.1.4.1.1166.1.11.3.1.12	INTEGER	read-only	The current and next Category Sequence Numbers
INT acpEmmCount	1.3.6.1.4.1.1166.1.11.3.1.13	INTEGER	read-only	The number of Category Rekey messages sent to this ACP.
INT acpProgramEpochNumber	1.3.6.1.4.1.1166.1.11.3.1.14	INTEGER	read-only	The current program epoch number for the service on this side of the ACP.
INT acpNextProgramEpochNumber	1.3.6.1.4.1.1166.1.11.3.1.15	INTEGER	read-only	The next program epoch number for the service on this side of the ACP.
INT acpNextServAuthorization	1.3.6.1.4.1.1166.1.11.3.1.16	INTEGER	read-only	ACP authorization status for the next Program Epoch for the service specified by acpServiceIndex
INT acpNextServAuthReasonCode	1.3.6.1.4.1.1166.1.11.3.1.17	INTEGER	read-only	ACP authorization reason code for the next Program Epoch for the service specified By acpServiceIndex.
INT acpInputSourceIdA	1.3.6.1.4.1.1166.1.11.3.1.18	INTEGER	read-only	The Input Source Id is used to identify the input source for this ACP in different products. One or both parts of the Id may be used in identifying where the input for the ACP comes from. When the Input Source Id A is set to 255 then the Id is invalid. If Id A is invalid the Id B is assumed invalid also. For example, the MPS uses the input source id to designate the location of the physical connector that is mapped to the ACP. In the case of the decrypt ACPs, InputSourceIdA is used to indicate the slot, and InputSourceIdB is used to indicate the port. Only decrypt ACPs have their source identified in this way. Encrypt ACPs do not have an identified source and their IdA is always set to Invalid (255).
INT acpInputSourceIdB	1.3.6.1.4.1.1166.1.11.3.1.19	INTEGER	read-only	The Input Source Id is used to identify the input source for this ACP in different products. One or both parts of the Id may be used in identifying where the input for the ACP comes from. For example, the MPS uses the input source id to designate the location of the physical connector that is mapped to the ACP. In the case of the decrypt ACPs, InputSourceIdA is used to indicate the slot, and InputSourceIdB is used to indicate the port. Only decrypt ACPs have their source identified in this way. Encrypt ACPs do not have an identified source.
acpPidTable	1.3.6.1.4.1.1166.1.11.4		not-accessible	A table of ACP entries giving assigned pid values
acpPidEntry	1.3.6.1.4.1.1166.1.11.4.1		not-accessible	A row in the ACP Pid Table
INT acpPidTblEncryptType	1.3.6.1.4.1.1166.1.11.4.1.1	INTEGER	not-accessible	The type of ACP in the system. It is either an encryptAcp or decryptAcp device.
INT acpPidTblUnitIndex	1.3.6.1.4.1.1166.1.11.4.1.2	INTEGER	not-accessible	The ACP unit index for this encrypt/decrypt type. For each type of ACP, encryptAcp or decryptAcp, the physical unit number of the ACP in the containing product, starting at 1.
INT acpPidTblServiceIndex	1.3.6.1.4.1.1166.1.11.4.1.3	INTEGER	not-accessible	For a specified ACP, identified by the both acpEncryptType and acpUnitIndex. The maximum limit on the value of this index is determined by the Max number of services supported by this ACP (for a TSODA, it is 2). For all other objects in the acpStatusTable, this index is not used. (it must be valid, but will not be used to access the object uniquely specified by acpEncryptType and acpUnitIndex)
INT acpPidTblPidIndex	1.3.6.1.4.1.1166.1.11.4.1.4	INTEGER	not-accessible	The PID index of the requested assigned PID value. multiple PIDs can be assigned per service
INT acpPidTblAssignedPid	1.3.6.1.4.1.1166.1.11.4.1.5	INTEGER	read-only	The PID assigned. If 0x1fff is returned then no PID is assigned.
INT acpPidTblEcmPid	1.3.6.1.4.1.1166.1.11.4.1.6	INTEGER	read-only	The ECM PID cooresponding to the assigned PID. Value set to 0x1fff when no ECM PID is programmed.
INT acpPidTblPidMask	1.3.6.1.4.1.1166.1.11.4.1.7	INTEGER	read-only	The PID mask used in conjunction with the assigned PID. Bits that are set in the PID Mask field of the ACP are 'dont cares' when comparing the PID of a received packet to the PID value configured in the ACP. For example, if the PID 0x0040 is configured in the ACP and the PID Mask is set to 0x000F, then any received packet with a PID from 0x0040 to 0x004F inclusive will be processed by the ACP.
INT acpMibRevision	1.3.6.1.4.1.1166.1.11.99	INTEGER	read-only	The current revision number of acp.mib multiplied by 100. To extract the major revision number divide by 100. The remainder is the minor revision number. The major rev number should be bumped whenever structural changes occur that require coresponding manager changes. Small changes like editing a description should bump the minor rev. The mib revision is matches the one found at the top of acp.mib

RFC description

Monitors Access Control Processor (ACP) encryption/decryption units and their operational status.

Start monitoring Motorola legacy access/telecom equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ACP-MIB

What Is ACP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description